Gerald Britton [Sat, 19 May 2007 17:18:22 +0000 (10:18 -0700)]
[PATCH] cciss: fix pci_driver.shutdown while device is still active
Fix an Oops in the cciss driver caused by system shutdown while a
filesystem on a cciss device is still active. The cciss_remove_one
function only properly removes the device if the device has been cleanly
released by its users, which is not the case when the pci_driver.shutdown
method is called.
This patch adds a new cciss_shutdown function to better match the pattern
used by various SCSI drivers: deactivate device interrupts and flush
caches. It also alters the cciss_remove_one function to match and readds
the __devexit annotation that was removed when cciss_remove_one was serving
as the pci_driver.shutdown method.
Signed-off-by: Gerald Britton <gbritton@alum.mit.edu> Acked-by: Mike Miller <mike.miller@hp.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Salyzyn, Mark [Tue, 15 May 2007 13:14:21 +0000 (09:14 -0400)]
[PATCH] SCSI: aacraid: Correct sa platform support. (Was: [Bug 8469] Bad EIP value on pentium3 SMP kernel-2.6.21.1)
http://bugzilla.kernel.org/show_bug.cgi?id=8469
As discussed in the bugzilla outlined below, we have an sa based
(Mustang) RAID adapter on the system, a Dell PERC2/QC. Affected
controllers are HP NetRAID, Adaptec AAC-364, Dell PERC2/QC or Adaptec
5400S. This problem coincides with the introduction of the adapter_comm
and adapter_deliver platform functions (Message [PATCH 1/4] aacraid:
rework communication support code, January 23 2007, which initially
migrated to 2.6.21)
The panic occurs with an uninitialized adapter_deliver platform function
pointer. The enclosed patch, unmodified as tested by Rainer, solves the
problem.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
[chrisw: backport to 2.6.21.4] Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Aaron Durbin [Thu, 17 May 2007 05:11:06 +0000 (22:11 -0700)]
[PATCH] acpi: fix potential call to a freed memory section.
Strip __cpuinit[data] from Node <-> PXM routines and supporting data
structures. Also make pxm_to_node_map and node_to_pxm_map local to the
numa acpi module.
This fixes a bug triggered by the following conditions:
- boot on a machine with a SLIT table defined
- kernel is configured w/ CONFIG_HOTPLUG_CPU=n
- cat /sys/devices/system/node/node*/distance
This will cause an oops by calling into a freed memory section.
In particular, on x86_64, __node_distance calls node_to_pxm().
Signed-off-by: Aaron Durbin <adurbin@google.com> Cc: Len Brown <lenb@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Alan Stern [Fri, 27 Apr 2007 18:32:47 +0000 (14:32 -0400)]
[PATCH] USB: set the correct Interrupt interval in usb_bulk_msg
This patch (as902) fixes a mistake I introduced into usb_bulk_msg().
usb_fill_int_urb() already does the bit-shifting calculation for
high-speed Interrupt intervals; it shouldn't be done twice.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Chris Wright [Fri, 1 Jun 2007 07:46:39 +0000 (00:46 -0700)]
[PATCH] x86: fix oprofile double free
Chuck reports that the recent fix from Andi to oprofile 6c977aad03a18019015035958c65b6729cd0574c introduces a double free. Each
cpu's cpu_msrs is setup to point to cpu 0's, which causes free_msrs to free
cpu 0's pointers for_each_possible_cpu. Rather than copy the pointers, do
a deep copy instead.
[acme@redhat.com: allocate_msrs() was using for_each_online_cpu()] Signed-off-by: Chris Wright <chrisw@sous-sol.org> Cc: Andi Kleen <ak@suse.de> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Cc: Dave Jones <davej@redhat.com> Cc: Chuck Ebbert <cebbert@redhat.com> Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jeff Dike [Tue, 5 Jun 2007 20:57:50 +0000 (16:57 -0400)]
[PATCH] UML - Improve host PTRACE_SYSEMU check
Make the PTRACE_SYSEMU checking more robust. It will make sure that
system call numbers are reported correctly. If there is a problem, it
will disable PTRACE_SYSEMU use and use PTRACE_SYSCALL instead.
This fixes a hang on boot on FC6 hosts with a broken PTRACE_SYSEMU.
Signed-off-by: Jeff Dike <jdike@linux.intel.com> Signed-off-by: Chris Wright <chrisw@sous-sol.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
--
arch/um/os-Linux/start_up.c | 24 ++++++++++++++++--------
1 file changed, 16 insertions(+), 8 deletions(-)
Michael Chan [Tue, 5 Jun 2007 18:34:20 +0000 (11:34 -0700)]
[PATCH] TG3: Fix link problem on Dell's onboard 5906.
The bug is caused by code that always set
(TG3_FLAG_USE_MI_INTERRUPT | TG3_FLAG_USE_LINKCHG_REG) on all Dell's
onboard devices. With these 2 flags set, the link status is polled
by tg3_timer() and will only work when the PHY is set up to interrupt
the MAC on link changes. This breaks 5906 because the 5906 PHY does
not support TG3_FLAG_USE_MI_INTERRUPT the same as other PHYs.
For correctness, only 5701 on Dell systems needs these 2 flags to be
set. This change will fix the 5906 problem and will change other
Dell devices except 5700 and 5701 to use the more efficient
interrupt-driven link changes.
Update version to 3.75.2.
Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Chris Wright <chrisw@sous-sol.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Ingo Molnar [Fri, 1 Jun 2007 07:47:16 +0000 (00:47 -0700)]
[PATCH] timer stats: speedups
Make timer-stats have almost zero overhead when enabled in the config but
not used. (this way distros can enable it more easily)
Also update the documentation about overhead of timer_stats - it was
written for the first version which had a global lock and a linear list
walk based lookup ;-)
Andrew says:
And this. Not a bugfix, but trivial and obvious and apparently some
distros don't want to enable timer_stats because of the performance
issue, but powertop uses timer_stats.
Ingo replies:
seconded. I have tested this with and without CONFIG_TIMER_STATS, with
and without timer_stats collection activated.
Signed-off-by: Ingo Molnar <mingo@elte.hu> Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Chris Wright <chrisw@sous-sol.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix two races in the timer stats lookup code. One by ensuring that the
initialization of a new entry is finished upon insertion of that entry.
The other by cleaning up the hash table when the entries array is cleared,
so that we don't have any "pre-inserted" entries.
Thanks to Eric Dumazet for reminding me of the memory barriers.
Signed-off-by: Bjorn Steinbrink <B.Steinbrink@gmx.de> Signed-off-by: Ian Kumlien <pomac@vapor.com> Acked-by: Ingo Molnar <mingo@elte.hu> Cc: Eric Dumazet <dada1@cosmosbay.com> Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Chris Wright <chrisw@sous-sol.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Oleg Nesterov [Fri, 1 Jun 2007 07:46:53 +0000 (00:46 -0700)]
[PATCH] tty: fix leakage of -ERESTARTSYS to userland
Spotted by Satoru Takeuchi.
kill_pgrp(task_pgrp(current)) sends the signal to the current's thread
group, but can choose any sub-thread as a target for signal_wake_up().
This means that job_control() and tty_check_change() may return
-ERESTARTSYS without signal_pending().
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru> Cc: Satoru Takeuchi <takeuchi_satoru@jp.fujitsu.com> Cc: Roland McGrath <roland@redhat.com> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Chris Wright <chrisw@sous-sol.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On systems with huge amount of physical memory, VFS cache and memory memmap
may eat all available system memory under 4G, then the system may fail to
allocate swiotlb bounce buffer.
There was a fix for this issue in arch/x86_64/mm/numa.c, but that fix dose
not cover sparsemem model.
This patch add fix to sparsemem model by first try to allocate memmap above
4G.
Signed-off-by: Zou Nan hai <nanhai.zou@intel.com> Acked-by: Suresh Siddha <suresh.b.siddha@intel.com> Cc: Andi Kleen <ak@suse.de> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[chrisw: trivial backport] Signed-off-by: Chris Wright <chrisw@sous-sol.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jay Cliburn [Sat, 26 May 2007 22:01:04 +0000 (17:01 -0500)]
[PATCH] PCI: quirk disable MSI on via vt3351
The Via VT3351 APIC does not play well with MSI and unleashes a flood
of APIC errors when MSI is used to deliver interrupts. The problem
was recently exposed when the atl1 network device driver, which enables
MSI by default, stimulated APIC errors on an Asus M2V mainboard, which
employs the Via VT3351.
See http://bugzilla.kernel.org/show_bug.cgi?id=8472 for additional
details on this bug.
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Hugh Dickins [Fri, 25 May 2007 23:39:17 +0000 (00:39 +0100)]
[PATCH] fix compat console unimap regression
Why is it that since the 2f1a2ccb9c0de632ab07193becf5f7121794f6ae console
UTF-8 fixes went into 2.6.22-rc1, the PowerMac G5 shows only inverse video
question marks for the text on tty2-6? whereas tty1 is fine, and so is x86.
No fault of that patch: by removing the old fallback behaviour, it reveals
that 32-bit setfont running on 64-bit kernels has only really worked on
the current console, the rest getting faked by that inadequate fallback.
Bring the compat do_unimap_ioctl into line with the main one: PIO_UNIMAP
and GIO_UNIMAP apply to the specified tty, not redirected to fg_console.
Use the same checks, and most particularly, remember to check access_ok:
con_set_unimap and con_get_unimap are using __get_user and __put_user.
And the compat vt_check should ask for the same capability as the main
one, CAP_SYS_TTY_CONFIG rather than CAP_SYS_ADMIN. Added in vt_ioctl's
vc_cons_allocated check for safety, though failure may well be impossible.
Daniel Drake [Thu, 24 May 2007 13:35:03 +0000 (09:35 -0400)]
[PATCH] zd1211rw: Add AL2230S RF support
ZD1211 appears to be back in production: a number of new devices have
been appearing! Some of them are using new radios.
This patch adds support for the next generation AL2230 RF chip which has
been spotted in a few new devices.
[As this patch was too late for 2.6.21, the kernel was modified to reject
AL2230S devices because for me and others, the devices silently failed (and
this looked like a driver bug). After doing so, a few people reported that
AL2230S devices were working correctly for them even before AL2230S support was
present. I'd like to propose that we fix both situations by backporting
the AL2230S support into 2.6.21-stable]
Signed-off-by: Daniel Drake <dsd@gentoo.org> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Chris Wright <chrisw@sous-sol.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Petri Helin found that this changeset broke tuning:
'Well, after going through the changes that might have had effect on
tuning, I found out the one which had caused this problem. I do not know
the actual reason behind the change, but the changelog says that it
was meant to "Fix TD1316 tuner for DVBC". But at least in my case it
seams to have broken the tuner instead.'
Signed-off-by: Oliver Endriss <o.endriss@gmx.de> Thanks-to: Petri Helin <phelin@googlemail.com> Acked-by: e9hack <e9hack@googlemail.com> Acked-by: Thomas Kaiser <linux-dvb@kaiser-linux.li> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org> Acked-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Chris Wright <chrisw@sous-sol.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Stefan Richter [Wed, 30 May 2007 05:33:47 +0000 (07:33 +0200)]
[PATCH] ieee1394: eth1394: bring back a parent device
This adds a real parent device to eth1394's ethX device like in Linux
2.6.20 and older. However, due to unfinished conversion of the ieee1394
away from class_device, we now refer to the FireWire controller's PCI
device as the parent, not to the ieee1394 driver's fw-host device.
Having a real parent device instead of a virtual one allows udev scripts
to distinguish eth1394 interfaces from networking bridges, bondings and
the likes.
Fixes a regression since 2.6.21:
https://bugs.gentoo.org/show_bug.cgi?id=177199
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Chris Wright <chrisw@sous-sol.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
[PATCH] Input: i8042 - fix AUX port detection with some chips
The i8042 driver fails detection of the AUX port with some chips,
because they apparently do not change the I8042_CTR_AUXDIS bit
immediately. This is known to affect at least HP500/HP510 notebooks,
consequently the built-in touchpad will not work. The patch will simply
reread the value until it gets the expected value or a retry limit is
hit, without touching other workaround code in the same area.
Signed-off-by: Roland Scheidegger <sroland@tungstengraphics.com> Signed-off-by: Dmitry Torokhov <dtor@mail.ru> Signed-off-by: Chris Wright <chrisw@sous-sol.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Daniel Drake [Thu, 24 May 2007 13:35:38 +0000 (09:35 -0400)]
[PATCH] ALSA: usb-audio: explicitly match Logitech QuickCam
Commit 93c8bf45e083b89dffe3a708363c15c1b220c723 modified the USB device
matching behaviour to ignore interface class matches if the device class
is vendor-specific.
This patch adds explicit ID matches for Logitech QuickCam devices, which
have a vendor specific device class (but standards-compliant audio
interfaces).
This fixes a 2.6.20 regression where the audio component of these
devices was no longer usable.
http://bugs.gentoo.org/show_bug.cgi?id=175715
https://bugs.launchpad.net/ubuntu/+source/linux-source-2.6.20/+bug/93822
https://bugtrack.alsa-project.org/alsa-bug/view.php?id=3040
Based on a patch from sergiom
Signed-off-by: Daniel Drake <dsd@gentoo.org> Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Jaroslav Kysela <perex@suse.cz> Signed-off-by: Chris Wright <chrisw@sous-sol.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Auke Kok [Fri, 1 Jun 2007 17:22:39 +0000 (10:22 -0700)]
[PATCH] e1000: disable polling before registering netdevice
To assure the symmetry of poll enable/disable in up/down, we should
initialize the netdevice to be poll_disabled at load time. Doing
this after register_netdevice leaves us open to another race, so
lets move all the netif_* calls above register_netdevice so the
stack starts out how we expect it to be.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com> Cc: Herbert Xu <herbert@gondor.apana.org.au> Cc: Doug Chapman <doug.chapman@hp.com> Signed-off-by: Jeff Garzik <jeff@garzik.org> Signed-off-by: Chris Wright <chrisw@sous-sol.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Takashi Iwai [Wed, 23 May 2007 20:44:36 +0000 (16:44 -0400)]
[PATCH] ALSA: hda-intel - Fix detection of audio codec on Toshiba A100
Some boards have the audio codec on slot #3 while the modem codec
on slot #0. The driver should continue to probe the slots when
no audio codec is found.
This fixes the problem of no device on Toshiba A100 (and some other
ATI SB450 devices).
Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jaroslav Kysela <perex@suse.cz> Signed-off-by: Chris Wright <chrisw@sous-sol.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Takashi Iwai [Wed, 23 May 2007 20:43:17 +0000 (16:43 -0400)]
[PATCH] ALSA: hda-intel - Probe additional slots only if necessary
Probing the codec slots on ATI controller causes problems on some
devices like Acer laptops. On these devices, reading from codec
slot 3 results in the communication failure with the codec chip.
Meanwhile, some laptops (e.g. Gateway) have the codec connection
only on slot 3, and probing this slot is mandatory for them.
The patch improves the probing robustness. The additional slots
are now checked only when no codecs are found in the primary three
slots.
Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jaroslav Kysela <perex@suse.cz> Signed-off-by: Chris Wright <chrisw@sous-sol.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Thomas Gleixner [Tue, 22 May 2007 06:38:50 +0000 (08:38 +0200)]
[PATCH] Prevent going idle with softirq pending
The NOHZ patch contains a check for softirqs pending when a CPU goes
idle. The BUG is unrelated to NOHZ, it just was made visible by the NOHZ
patch. The BUG showed up mainly on P4 / hyperthreading enabled machines
which lead the investigations into the wrong direction in the first
place. The real cause is in cond_resched_softirq():
cond_resched_softirq() is enabling softirqs without invoking the softirq
daemon when softirqs are pending. This leads to the warning message in
the NOHZ idle code:
t1 runs softirq disabled code on CPU#0
interrupt happens, softirq is raised, but deferred (softirqs disabled)
t1 calls cond_resched_softirq()
enables softirqs via _local_bh_enable()
calls schedule()
t2 runs
t1 is migrated to CPU#1
t2 is done and invokes idle()
NOHZ detects the pending softirq
Fix: change _local_bh_enable() to local_bh_enable() so the softirq
daemon is invoked.
Thanks to Anant Nitya for debugging this with great patience !
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Cc: Anant Nitya <kernel@prachanda.info> Signed-off-by: Chris Wright <chrisw@sous-sol.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
NeilBrown [Mon, 21 May 2007 01:33:10 +0000 (11:33 +1000)]
[PATCH] md: Don't write more than is required of the last page of a bitmap
It is possible that real data or metadata follows the bitmap
without full page alignment.
So limit the last write to be only the required number of bytes,
rounded up to the hard sector size of the device.
Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Chris Wright <chrisw@sous-sol.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
NeilBrown [Mon, 21 May 2007 01:33:03 +0000 (11:33 +1000)]
[PATCH] md: Avoid overflow in raid0 calculation with large components.
If a raid0 has a component device larger than 4TB, and is accessed on
a 32bit machines, then as 'chunk' is unsigned lock,
chunk << chunksize_bits
can overflow (this can be as high as the size of the device in KB).
chunk itself will not overflow (without triggering a BUG).
So change 'chunk' to be 'sector_t, and get rid of the 'BUG' as it becomes
impossible to hit.
Cc: "Jeff Zheng" <Jeff.Zheng@endace.com> Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Chris Wright <chrisw@sous-sol.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Andi Kleen [Mon, 21 May 2007 12:31:45 +0000 (14:31 +0200)]
[PATCH] i386: Fix K8/core2 oprofile on multiple CPUs
Only try to allocate MSRs once instead of for every CPU.
This assumes the MSRs are the same on all CPUs which is currently
true. P4-HT is a special case for different SMT threads, but the code
always saves/restores all MSRs so it works identical.
Thomas Gleixner [Wed, 23 May 2007 20:57:37 +0000 (13:57 -0700)]
[PATCH] NOHZ: Rate limit the local softirq pending warning output
The warning in the NOHZ code, which triggers when a CPU goes idle with
softirqs pending can fill up the logs quite quickly. Rate limit the output
until we found the root cause of that problem.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Chris Wright <chrisw@sous-sol.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Thomas Gleixner [Sat, 19 May 2007 14:22:50 +0000 (16:22 +0200)]
[PATCH] Ignore bogus ACPI info for offline CPUs
Booting a SMP kernel with maxcpus=1 on a SMP system leads to a hard
hang, because ACPI ignores the maxcpus setting and sends timer broadcast
info for the offline CPUs. This results in a stuck for ever call to
smp_call_function_single() on an offline CPU.
Ignore the bogus information and print a kernel error to remind ACPI
folks to fix it.
Affects 2.6.21 / 2.6.22-rc
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Chris Wright <chrisw@sous-sol.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When creating a new connection by sending an unknown chunk type, we
don't transition to a valid state, causing a NULL pointer dereference in
sctp_packet when accessing sctp_timeouts[SCTP_CONNTRACK_NONE].
Fix by don't creating new conntrack entry if initial state is invalid.
Noticed by Vilmos Nebehaj <vilmos.nebehaj@ramsys.hu>
CC: Kiran Kumar Immidi <immidi_kiran@yahoo.com> Cc: David Miller <davem@davemloft.net> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Allow in-place crypto operations. Also remove the coherent user flag
(we use it automagically now), and by default use the user written
key rather then the HW hidden key - this makes crypto just work without
any special considerations, and thats OK, since its our only usage
model.
Signed-off-by: Jordan Crouse <jordan.crouse@amd.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Herbert Xu [Sat, 19 May 2007 04:57:38 +0000 (14:57 +1000)]
[PATCH] CRYPTO: api: Read module pointer before freeing algorithm
The function crypto_mod_put first frees the algorithm and then drops
the reference to its module. Unfortunately we read the module pointer
which after freeing the algorithm and that pointer sits inside the
object that we just freed.
So this patch reads the module pointer out before we free the object.
Thanks to Luca Tettamanti for reporting this.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Daniel Drake [Tue, 15 May 2007 19:59:03 +0000 (19:59 +0000)]
[PATCH] CPUFREQ: powernow-k7: fix MHz rounding issue with perflib
When the PST tables are broken, powernow-k7 uses ACPI's processor_perflib to
deduce the available frequency multipliers from the _PSS tables.
Upon frequency change, processor_perflib performs some verification on the
frequency (checks that it's within allowable bounds).
powernow-k7 deals with absolute frequencies in KHz, whereas perflib only
deals with MHz values. When performing the above verification, perflib
multiplies the MHz values by 1000 to obtain the KHz value.
We then end up with situations like the following:
- powernow-k7 multiplies the multiplier by the FSB, and obtains a value
such as 1266768 KHz
- perflib belives the same state has frequency of 1266 MHz
- acpi_processor_ppc_notifier calls cpufreq_verify_within_limits to verify
that 1266768 is in the allowable range of 0 to 1266000 (i.e. 1266 * 1000)
- it's not, so that frequency is rejected
- the maximum CPU frequency is not reachable
This patch solves the problem by rounding up the MHz values stored in perflib's
tables. Additionally it corrects a broken URL.
It also fixes http://bugzilla.kernel.org/show_bug.cgi?id=8255 although this
case is a bit different: the frequencies in the _PSS tables are wildly wrong,
but we get better results if we force ACPI to respect the fsb * multiplier
calculations (even though it seems that the multiplier values aren't entirely
correct either).
Signed-off-by: Daniel Drake <dsd@gentoo.org> Signed-off-by: Dave Jones <davej@redhat.com> Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Dave Jones [Mon, 14 May 2007 22:27:29 +0000 (18:27 -0400)]
[PATCH] CPUFREQ: Correct revision mask for powernow-k8
Mark Langsdorf points out that the correct define for this
revision bump is 0x80000. Also to save us having to keep
renaming the #define, give it a more meaningful name.
Signed-off-by: Dave Jones <davej@redhat.com> Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Patrick McHardy [Wed, 16 May 2007 16:56:11 +0000 (18:56 +0200)]
[PATCH] NETFILTER: {ip,nf}_conntrack: fix use-after-free in helper destroy callback invocation
When the helper module is removed for a master connection that has a
fulfilled expectation, but has already timed out and got removed from
the hash tables, nf_conntrack_helper_unregister can't find the master
connection to unset the helper, causing a use-after-free when the
expected connection is destroyed and releases the last reference to
the master.
The helper destroy callback was introduced for the PPtP helper to clean
up expectations and expected connections when the master connection
times out, but doing this from destroy_conntrack only works for
unfulfilled expectations since expected connections hold a reference
to the master, preventing its destruction. Move the destroy callback to
the timeout function, which fixes both problems.
Reported/tested by Gabor Burjan <buga@buvoshetes.hu>.
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Dave Kleikamp [Wed, 16 May 2007 03:53:36 +0000 (22:53 -0500)]
[PATCH] JFS: Fix race waking up jfsIO kernel thread
It's possible for a journal I/O request to be added to the log_redrive
queue and the jfsIO thread to be awakened after the thread releases
log_redrive_lock but before it sets its state to TASK_INTERRUPTIBLE.
The jfsIO thread should set the state before giving up the spinlock, so
the waking thread will really wake it.
Signed-off-by: Dave Kleikamp <shaggy@linux.vnet.ibm.com> Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Jiri Kosina [Tue, 15 May 2007 22:44:59 +0000 (00:44 +0200)]
[PATCH] USB HID: hiddev - fix race between hiddev_send_event() and hiddev_release()
USB HID: hiddev - fix race between hiddev_send_event() and hiddev_release()
There is a small race window in which hiddev_release() could corrupt the
list that is being processed for new event in hiddev_send_event().
Synchronize the operations over this list.
Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Chris Wright <chrisw@sous-sol.org>
If the device fails during module startup for some reason like unsupported chip
version then the driver would crash dereferencing a null pointer, on shutdown
or suspend/resume.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: Chris Wright <chrisw@sous-sol.org>
If device fails during module startup for some reason (like unsupported chip
version) then driver would crash dereferencing a null pointer, on shutdown
or suspend/resume.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Herbert Xu [Tue, 15 May 2007 08:36:48 +0000 (01:36 -0700)]
[PATCH] IPSEC: Check validity of direction in xfrm_policy_byid
The function xfrm_policy_byid takes a dir argument but finds the policy
using the index instead. We only use the dir argument to update the
policy count for that direction. Since the user can supply any value
for dir, this can corrupt our policy count.
I know this is the problem because a few days ago I was deleting
policies by hand using indicies and accidentally typed in the wrong
direction. It still deleted the policy and at the time I thought
that was cool. In retrospect it isn't such a good idea :)
I decided against letting it delete the policy anyway just in case
we ever remove the connection between indicies and direction.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Vlad Yasevich [Tue, 15 May 2007 08:32:35 +0000 (01:32 -0700)]
[PATCH] SCTP: Prevent OOPS if hmac modules didn't load
SCTP was checking for NULL when trying to detect hmac
allocation failure where it should have been using IS_ERR.
Also, print a rate limited warning to the log telling the
user what happend.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Jamal Hadi Salim [Tue, 15 May 2007 08:23:46 +0000 (01:23 -0700)]
[PATCH] NET_SCHED: prio qdisc boundary condition
This fixes an out-of-boundary condition when the classified
band equals q->bands. Caught by Alexey
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Corey Mutter [Tue, 15 May 2007 08:22:59 +0000 (01:22 -0700)]
[PATCH] IPV6: Reverse sense of promisc tests in ip6_mc_input
Reverse the sense of the promiscuous-mode tests in ip6_mc_input().
Signed-off-by: Corey Mutter <crm-netdev@mutternet.com> Signed-off-by: David L Stevens <dlstevens@us.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Chris Wright <chrisw@sous-sol.org>
[PATCH] IPV6 ROUTE: Assign rt6i_idev for ip6_{prohibit,blk_hole}_entry.
I think this is less critical, but is also suitable for -stable
release.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Chris Wright <chrisw@sous-sol.org>
[PATCH] IPV6: Do no rely on skb->dst before it is assigned.
Because skb->dst is assigned in ip6_route_input(), it is really
bad to use it in hop-by-hop option handler(s).
Closes: Bug #8450 (Eric Sesterhenn <snakebyte@gmx.de>) Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Chris Wright <chrisw@sous-sol.org>
David L Stevens [Tue, 15 May 2007 07:02:07 +0000 (00:02 -0700)]
[PATCH] IPV6: Send ICMPv6 error on scope violations.
When an IPv6 router is forwarding a packet with a link-local scope source
address off-link, RFC 4007 requires it to send an ICMPv6 destination
unreachable with code 2 ("not neighbor"), but Linux doesn't. Fix below.
Signed-off-by: David L Stevens <dlstevens@us.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Chris Wright <chrisw@sous-sol.org>
A recent code cleanup that moved code from mptscsih to mptspi inadvertently
change the order some code was called. This caused a massive slowdown (of
150x to 300x) on the CD/DVD drive on the high-end HP Integrity servers.
Signed-off-by: Doug Chapman <doug.chapman@hp.com> Cc: <Eric.Moore@lsil.com> Cc: James Bottomley <James.Bottomley@steeleye.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Tejun Heo [Fri, 11 May 2007 05:58:51 +0000 (22:58 -0700)]
[PATCH] pci-quirks: disable MSI on RS400-200 and RS480
MSI doesn't work on RS400-200 and RS480 requiring pci=nomsi kernel boot
parameter for ahci to work. This patch renames quirk_svw_msi() to
quirk_disable_all_msi() and use it to disable MSI on those chips.
Tejun Heo [Thu, 10 May 2007 14:45:17 +0000 (16:45 +0200)]
[PATCH] driver-core: don't free devt_attr till the device is released
Currently, devt_attr for the "dev" file is freed immediately on device
removal, but if the "dev" sysfs file is open when a device is removed,
sysfs will access its attribute structure for further access including
close resulting in jumping to garbled address. Fix it by postponing
freeing devt_attr to device release time.
Note that devt_attr for class_device is already freed on release.
This bug is reported by Chris Rankin as bugzilla bug#8198.
Signed-off-by: Tejun Heo <htejun@gmail.com> Cc: Chris Rankin <rankincj@yahoo.com> Signed-off-by: Chris Wright <chrisw@sous-sol.org>
NeilBrown [Thu, 10 May 2007 06:22:25 +0000 (16:22 +1000)]
[PATCH] md: Avoid a possibility that a read error can wrongly propagate through md/raid1 to a filesystem.
When a raid1 has only one working drive, we want read error to
propagate up to the filesystem as there is no point failing the last
drive in an array.
Currently the code perform this check is racy. If a write and a read
a both submitted to a device on a 2-drive raid1, and the write fails
followed by the read failing, the read will see that there is only one
working drive and will pass the failure up, even though the one
working drive is actually the *other* one.
So, tighten up the locking.
Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Thomas Gleixner [Wed, 9 May 2007 09:35:15 +0000 (02:35 -0700)]
[PATCH] clocksource: fix resume logic
We need to make sure that the clocksources are resumed, when timekeeping is
resumed. The current resume logic does not guarantee this.
Add a resume function pointer to the clocksource struct, so clocksource
drivers which need to reinitialize the clocksource can provide a resume
function.
Add a resume function, which calls the maybe available clocksource resume
functions and resets the watchdog function, so a stable TSC can be used
accross suspend/resume.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: john stultz <johnstul@us.ibm.com> Cc: Andi Kleen <ak@suse.de> Cc: Ingo Molnar <mingo@elte.hu> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Ken Chen [Wed, 9 May 2007 09:33:09 +0000 (02:33 -0700)]
[PATCH] fix leaky resv_huge_pages when cpuset is in use
The internal hugetlb resv_huge_pages variable can permanently leak nonzero
value in the error path of hugetlb page fault handler when hugetlb page is
used in combination of cpuset. The leaked count can permanently trap N
number of hugetlb pages in unusable "reserved" state.
Steps to reproduce the bug:
(1) create two cpuset, user1 and user2
(2) reserve 50 htlb pages in cpuset user1
(3) attempt to shmget/shmat 50 htlb page inside cpuset user2
(4) kernel oom the user process in step 3
(5) ipcrm the shm segment
At this point resv_huge_pages will have a count of 49, even though
there are no active hugetlbfs file nor hugetlb shared memory segment
in the system. The leak is permanent and there is no recovery method
other than system reboot. The leaked count will hold up all future use
of that many htlb pages in all cpusets.
The culprit is that the error path of alloc_huge_page() did not
properly undo the change it made to resv_huge_page, causing
inconsistent state.
Signed-off-by: Ken Chen <kenchen@google.com> Cc: David Gibson <david@gibson.dropbear.id.au> Cc: Adam Litke <agl@us.ibm.com> Cc: Martin Bligh <mbligh@google.com> Acked-by: David Gibson <dwg@au1.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Srinivas Aji [Wed, 9 May 2007 08:33:58 +0000 (01:33 -0700)]
[PATCH] TCP: zero out rx_opt in tcp_disconnect()
When the server drops its connection, NFS client reconnects using the
same socket after disconnecting. If the new connection's SYN,ACK
doesn't contain the TCP timestamp option and the old connection's did,
tp->tcp_header_len is recomputed assuming no timestamp header but
tp->rx_opt.tstamp_ok remains set. Then tcp_build_and_update_options()
adds in a timestamp option past the end of the allocated TCP header,
overwriting TCP data, or when the data is in skb_shinfo(skb)->frags[],
overwriting skb_shinfo(skb) causing a crash soon after. (The issue was
debugged from such a crash.)
Similarly, wscale_ok and sack_ok also get set based on the SYN,ACK
packet but not reset on disconnect, since they are zeroed out at
initialization. The patch zeroes out the entire tp->rx_opt struct in
tcp_disconnect() to avoid this sort of problem.
Signed-off-by: Srinivas Aji <Aji_Srinivas@emc.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Vlad Yasevich [Wed, 9 May 2007 20:51:31 +0000 (13:51 -0700)]
[PATCH] SCTP: Correctly copy addresses in sctp_copy_laddrs
I broke the non-wildcard case recently. This is to fixes it.
Now, explictitly bound addresses can ge retrieved using the API.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Vlad Yasevich [Wed, 9 May 2007 08:31:28 +0000 (01:31 -0700)]
[PATCH] SCTP: Fix sctp_getsockopt_local_addrs_old() to use local storage.
sctp_getsockopt_local_addrs_old() in net/sctp/socket.c calls
copy_to_user() while the spinlock addr_lock is held. this should not
be done as copy_to_user() might sleep. the call to
sctp_copy_laddrs_to_user() while holding the lock is also problematic
as it calls copy_to_user()
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Sergei Shtylyov [Wed, 9 May 2007 08:29:18 +0000 (01:29 -0700)]
[PATCH] NETPOLL: Remove CONFIG_NETPOLL_RX
Get rid of the CONFIG_NETPOLL_RX option completely since all the
dependencies have been removed long ago...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Acked-by: Jeff Garzik <jgarzik@pobox.com> Acked-by: Matt Mackall <mpm@selenic.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Sergei Shtylyov [Wed, 9 May 2007 08:27:55 +0000 (01:27 -0700)]
[PATCH] NETPOLL: Fix TX queue overflow in trapped mode.
CONFIG_NETPOLL_TRAP causes the TX queue controls to be completely bypassed in
the netpoll's "trapped" mode which easily causes overflows in the drivers with
short TX queues (most notably, in 8139too with its 4-deep queue). So, make
this option more sensible by making it only bypass the TX softirq wakeup.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Acked-by: Jeff Garzik <jgarzik@pobox.com> Acked-by: Tom Rini <trini@kernel.crashing.org> Acked-by: Matt Mackall <mpm@selenic.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Eric Sesterhenn [Wed, 9 May 2007 08:20:59 +0000 (01:20 -0700)]
[PATCH] IPV6: Fix slab corruption running ip6sic
Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Stephen Mollett [Tue, 8 May 2007 07:31:31 +0000 (00:31 -0700)]
[PATCH] udf: decrement correct link count in udf_rmdir
It appears that a minor thinko occurred in udf_rmdir and the
(already-cleared) link count on the directory that is being removed was
being decremented instead of the link count on its parent directory. This
gives rise to lots of kernel messages similar to:
when removing directory trees. No other ill effects have been observed but
I guess it could theoretically result in the link count overflowing on a
very long-lived, much modified directory.
Signed-off-by: Stephen Mollett <molletts@yahoo.com> Cc: Dave Hansen <haveblue@us.ibm.com> Cc: Jan Kara <jack@ucw.cz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Chris Wright <chrisw@sous-sol.org>
OGAWA Hirofumi [Tue, 8 May 2007 07:31:28 +0000 (00:31 -0700)]
[PATCH] fat: fix VFAT compat ioctls on 64-bit systems
If you compile and run the below test case in an msdos or vfat directory on
an x86-64 system with -m32 you'll get garbage in the kernel_dirent struct
followed by a SIGSEGV.
The patch fixes this.
Reported and initial fix by Bart Oldeman
#include <sys/types.h>
#include <sys/ioctl.h>
#include <dirent.h>
#include <stdio.h>
#include <unistd.h>
#include <fcntl.h>
struct kernel_dirent {
long d_ino;
long d_off;
unsigned short d_reclen;
char d_name[256]; /* We must not include limits.h! */
};
#define VFAT_IOCTL_READDIR_BOTH _IOR('r', 1, struct kernel_dirent [2])
#define VFAT_IOCTL_READDIR_SHORT _IOR('r', 2, struct kernel_dirent [2])
int main(void)
{
int fd = open(".", O_RDONLY);
struct kernel_dirent de[2];
while (1) {
int i = ioctl(fd, VFAT_IOCTL_READDIR_BOTH, (long)de);
if (i == -1) break;
if (de[0].d_reclen == 0) break;
printf("SFN: reclen=%2d off=%d ino=%d, %-12s",
de[0].d_reclen, de[0].d_off, de[0].d_ino, de[0].d_name);
if (de[1].d_reclen)
printf("\tLFN: reclen=%2d off=%d ino=%d, %s",
de[1].d_reclen, de[1].d_off, de[1].d_ino, de[1].d_name);
printf("\n");
}
return 0;
}
Signed-off-by: Bart Oldeman <bartoldeman@users.sourceforge.net> Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Chris Wright <chrisw@sous-sol.org>
While the !highres/!dyntick code assigns the duty of the do_timer() call to
one specific CPU, this was dropped in the highres/dyntick part during
development.
Steven Rostedt discovered the xtime lock contention on highres/dyntick due
to several CPUs trying to update jiffies.
Add the single CPU assignement back. In the dyntick case this needs to be
handled carefully, as the CPU which has the do_timer() duty must drop the
assignement and let it be grabbed by another CPU, which is active.
Otherwise the do_timer() calls would not happen during the long sleep.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Ingo Molnar <mingo@elte.hu> Cc: Steven Rostedt <rostedt@goodmis.org> Acked-by: Mark Lord <mlord@pobox.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Michael Chan [Tue, 8 May 2007 02:04:43 +0000 (19:04 -0700)]
[PATCH] BNX2: Update version and reldate.
Update version to 1.5.8.1.
Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Michael Chan [Tue, 8 May 2007 02:04:35 +0000 (19:04 -0700)]
[PATCH] BNX2: Save PCI state during suspend.
This is needed to save the MSI state which will be lost during
suspend.
Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Michael Chan [Tue, 8 May 2007 02:04:28 +0000 (19:04 -0700)]
[PATCH] BNX2: Block MII access when ifdown.
The device may be in D3hot state and should not allow MII register
access.
Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Michael Chan [Tue, 8 May 2007 02:04:17 +0000 (19:04 -0700)]
[PATCH] BNX2: Fix TSO problem with small MSS.
Remove the check for skb->len greater than MTU when doing TSO. When
the destination has a smaller MSS than the source, a TSO packet may
be smaller than the MTU at the source and we still need to process it
as a TSO packet.
Thanks to Brian Ristuccia <bristuccia@starentnetworks.com> for
reporting the problem.
Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Michael Chan [Tue, 8 May 2007 02:03:53 +0000 (19:03 -0700)]
[PATCH] TG3: Remove reset during MAC address changes.
The reset was added a while back so that ASF could re-init whatever
MAC address it wanted to use after the MAC address was changed.
Instead of resetting, we can just keep MAC address 1 unchanged during
MAC address changes if MAC address 1 is different from MAC address 0.
This fixes 2 problems:
1. Bonding calls set_mac_address in contexts that cannot sleep.
It no longer sleeps with the chip reset removed.
2. When ASF shares the same MAC address as the NIC, it needs to
always do that even when the MAC address is changed.
Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Michael Chan [Tue, 8 May 2007 02:03:37 +0000 (19:03 -0700)]
[PATCH] TG3: Fix TSO bugs.
1. Remove the check for skb->len greater than MTU when doing TSO.
When the destination has a smaller MSS than the source, a TSO packet
may be smaller than the MTU and we still need to process it as a TSO
packet.
2. On 5705A3 devices with TSO enabled, the DMA engine can hang due to a
hardware bug. This patch avoids the hanging condition by reducing the
DMA burst size.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Chris Wright <chrisw@sous-sol.org>
[PATCH] skge: default WOL should be magic only (rev2)
By default, the skge driver now enables wake on magic and wake on PHY.
This is a bad default (bug), wake on PHY means machine will never shutdown
if connected to a switch.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Richard Purdie [Sun, 6 May 2007 21:51:56 +0000 (14:51 -0700)]
[PATCH] ppp: Fix ppp_deflate issues with recent zlib_inflate changes
The last zlib_inflate update broke certain corner cases for ppp_deflate
decompression handling. This patch fixes some logic to make things work
properly again. Users other than ppp_deflate (the only Z_PACKET_FLUSH
user) should be unaffected.
Fixes bug 8405 (confirmed by Stefan)
Signed-off-by: Richard Purdie <rpurdie@rpsys.net> Cc: Stefan Wenk <stefan.wenk@gmx.at> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Akinobu Mita [Sun, 6 May 2007 21:50:19 +0000 (14:50 -0700)]
[PATCH] slob: fix page order calculation on not 4KB page
SLOB doesn't calculate correct page order when page size is not 4KB. This
patch fixes it with using get_order() instead of find_order() which is SLOB
version of get_order().
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Acked-by: Matt Mackall <mpm@selenic.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Chris Wright <chrisw@sous-sol.org>
projects / karo-tx-linux.git / log