Merge tag 'usb-for-v4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v4.8 merge window
Here's the big pull request for Peripheral stack and
all related drivers.
This time around with 109 non-merge commits mostly
concentrated on drivers/usb/gadget/udc (41.5%) and
drivers/usb/dwc3 (28.1%).
There's a big rework on dwc3's transfer handling
which gave us almost 3x faster USB3 speeds with Mass
Storage on a particular test scenario I measured. We
are also removing platform_data from dwc3 after
converting all users to built-in properties instead.
For the Gadget API, we're just adding tracepoints to
aid debugging activities.
Other than these, there's the usual set of spelling
fixes, minor bug fixes and sparse warnings cleanups.
usb: renesas_usbhs: protect the CFIFOSEL setting in usbhsg_ep_enable()
This patch fixes an issue that the CFIFOSEL register value is possible
to be changed by usbhsg_ep_enable() wrongly. And then, a data transfer
using CFIFO may not work correctly.
For example:
# modprobe g_multi file=usb-storage.bin
# ifconfig usb0 192.168.1.1 up
(During the USB host is sending file to the mass storage)
# ifconfig usb0 down
In this case, since the u_ether.c may call usb_ep_enable() in
eth_stop(), if the renesas_usbhs driver is also using CFIFO for
mass storage, the mass storage may not work correctly.
So, this patch adds usbhs_lock() and usbhs_unlock() calling in
usbhsg_ep_enable() to protect CFIFOSEL register. This is because:
- CFIFOSEL.CURPIPE = 0 is also needed for the pipe configuration
- The CFIFOSEL (fifo->sel) is already protected by usbhs_lock()
usb: renesas_usbhs: fix NULL pointer dereference in xfer_work()
This patch fixes an issue that the xfer_work() is possible to cause
NULL pointer dereference if the usb cable is disconnected while data
transfer is running.
In such case, a gadget driver may call usb_ep_disable()) before
xfer_work() is actually called. In this case, the usbhs_pkt_pop()
will call usbhsf_fifo_unselect(), and then usbhs_pipe_to_fifo()
in xfer_work() will return NULL.
Dan Carpenter [Fri, 24 Jun 2016 12:23:16 +0000 (15:23 +0300)]
usb: gadget: f_fs: check for allocation failure
Return -ENOMEM if kmalloc() fails.
Fixes: 9353afbbfa7b ('usb: gadget: f_fs: buffer data from ‘oversized’ OUT requests') Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Michal Nazarewicz <mina86@mina86.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Arnd Bergmann [Fri, 24 Jun 2016 07:30:26 +0000 (09:30 +0200)]
USB: dwc2-usb: add USB_GADGET dependency
The driver selects NOP_USB_XCEIV, which can only be built-in if
USB_GADGET is either disabled or also built-in, so with USB_DWC2_PCI=y
and USB_GADGET=m, NOP_USB_XCEIV is also built-in and we get this link
error:
drivers/usb/built-in.o: In function `nop_set_peripheral':
(text+0x1927c): undefined reference to `usb_gadget_vbus_connect'
drivers/usb/built-in.o: In function `nop_gpio_vbus_thread':
(text+0x197a0): undefined reference to `usb_gadget_vbus_connect'
(text+0x19830): undefined reference to `usb_gadget_vbus_disconnect'
This adds the same dependency for the dwc2 driver to avoid that
broken configuration.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Nicolas Iooss [Sun, 26 Jun 2016 08:12:38 +0000 (10:12 +0200)]
usb: dwc2: add printf attribute to cat_printf()
As cat_printf() uses printf format strings in its parameters, adding
__printf attribute allows the compiler to detect at compile-time some
errors related to format strings (with -Wformat warning flag).
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org> Acked-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Heikki Krogerus [Tue, 21 Jun 2016 07:58:08 +0000 (10:58 +0300)]
xhci: plat: adapt to unified device property interface
Requesting the only property that the driver needs using the
unified device property interface so it will be available
for all types of platforms, not just the ones using DT.
Mathias Nyman [Tue, 21 Jun 2016 07:58:05 +0000 (10:58 +0300)]
xhci: rework inc_deq() and fix off by one error.
inc_deq() is called both for rings with link trbs and the event ring
without link trbs.
The last_trb() check in inc_deq() has a off by one error, going beyond
allocated array when checking if trb == [TRBS_PER_SEGMENT], and the whole
inc_deq() depend on this.
Rewrite the inc_deq() funciton, remove the faulty last_trb() helper, add
new last_trb_on_seg() and last_trb_on_ring() helpers
Mathias Nyman [Tue, 21 Jun 2016 07:58:04 +0000 (10:58 +0300)]
xhci: use and add separate function for checking for link trbs
Add a new is_link_trb() function that only checks for link trbs.
We want to split generic last_trb() function which is used for both
event rings without link trbs, and endpoint and command rings with links.
This will allow us to easier check for link trbs added mid segments.
Mathias Nyman [Tue, 21 Jun 2016 07:58:02 +0000 (10:58 +0300)]
xhci: TD-fragment, align the unsplittable case with a bounce buffer
If the last trb before a link is not packet size aligned, and is not
splittable then use a bounce buffer for that chunk of max packet size
unalignable data.
Allocate a max packet size bounce buffer for every segment of a bulk
endpoint ring at the same time as allocating the ring.
If we need to align the data before the link trb in that segment then
copy the data to the segment bounce buffer, dma map it, and enqueue it.
Once the td finishes, or is cancelled, unmap it.
For in transfers we need to first map the bounce buffer, then queue it,
after it finishes, copy the bounce buffer to the original sg list, and
finally unmap it
Mathias Nyman [Tue, 21 Jun 2016 07:58:01 +0000 (10:58 +0300)]
xhci: align the last trb before link if it is easily splittable.
TD fragments section 4.11.7.1 in xhci specs have additional requirements
on how trbs in TDs must be organized.
TD fragments shall not span transfer ring segments and TD fragments must
be packet aligned. Normally we don't care about TD fragments, on TD is one
big fragment, but if a TD spans ring segments it will be treated as two
fragments, and we need to comply with the alignment requirements.
For us this means that the payload data must be packet aligned in the
last trb before a link trb.
In most mass storage bulk tranfers we are lucky as the block size aligns
nicely with packet size, and there are no issues.
However, usb network adapters using scatterlists can hit this alignment
issue, and usbtest in kernel triggers this in minutes.
This patch is a partial solution, it solves the easy case when the last
trb before the link trb contains a packet boundary.
If that is the case then just split the trb at the boundary.
If not, then just print a debug message and continue as we have always
done, hoping for the best
Mathias Nyman [Tue, 21 Jun 2016 07:58:00 +0000 (10:58 +0300)]
xhci: don't rely on precalculated value of needed trbs in the enqueue loop
Queue trbs until all payload data in the urb is tranferred.
The actual number of trbs might need to change from the pre-calculated
number when the packet alignment restrictions for td fragments in
xhci 4.11.7.1 are taken into account.
Long term plan is to get rid of calculating the needed trbs in advance
all together. It's an unnecessary extra walk through the scatterlist.
This change also allows some bulk queue function simplifications
Mathias Nyman [Tue, 21 Jun 2016 07:57:59 +0000 (10:57 +0300)]
xhci: use boolean to indicate last trb in td remainder calculation
We only need to know if we are queuing the last trb for a TD when
calculating the td remainder field.
The total number of trbs left is not used.
We won't be able to trust the pre-calculated number of trbs used if we
need to align trb data by splitting or merging trbs in order to satisfy
comply with data alignment requirements in xhci specs section 4.11.7.1.
Mathias Nyman [Tue, 21 Jun 2016 07:57:58 +0000 (10:57 +0300)]
xhci: properly prepare zero packet TD after normal bulk TD.
If a zero-length packet is needed after a bulk transfer, then an
additional zero length TD was prepared before enqueueing the bulk transfer
This set up the zero packet TD structure with incorrect td->start_seg
and td->first_trb pointers.
Prepare the zero packet TD after the data bulk TD is enqueued instead.
It sets these pointers correctly.
This change also simplifies unnecessary complexity related to keeping
track of the last trb when enqueuing trbs.
Mathias Nyman [Tue, 21 Jun 2016 07:57:57 +0000 (10:57 +0300)]
xhci: rename ep_ring variable in queue_bulk_tx(), no functional change
Tiny change, a bit more readable.
The real reason for this change is that the coming td fragment work
had several over 80 lines character lines split just because of a few
extra characters in variable names.
Iago Abal [Tue, 21 Jun 2016 10:01:11 +0000 (12:01 +0200)]
usb: gadget: pch_udc: reorder spin_[un]lock to avoid deadlock
The above commit reordered spin_lock/unlock and now `&dev->lock' is acquired
(rather than released) before calling `dev->driver->disconnect',
`dev->driver->setup', `dev->driver->suspend', `usb_gadget_giveback_request', and
`usb_gadget_udc_reset'.
But this *may* not be the right way to fix the problem pointed by d3cb25a12138.
Note that the other usb/gadget/udc drivers do release the lock before calling
these functions. There are also inconsistencies within pch_udc.c, where
`dev->driver->disconnect' is called while holding `&dev->lock' in lines 613 and
1184, but not in line 2739.
Finally, commit d3cb25a12138 may have introduced several potential deadlocks.
For instance, EBA (https://github.com/models-team/eba) reports:
Double lock in drivers/usb/gadget/udc/pch_udc.c
first at 2791: spin_lock(& dev->lock); [pch_udc_isr]
second at 2694: spin_lock(& dev->lock); [pch_udc_svc_cfg_interrupt]
after calling from 2793: pch_udc_dev_isr(dev, dev_intr);
after calling from 2724: pch_udc_svc_cfg_interrupt(dev);
Similarly, other potential deadlocks are 2791 -> 2793 -> 2721 -> 2657; and
2791 -> 2793 -> 2711 -> 2573 -> 1499 -> 1480.
Fixes: d3cb25a12138 ("usb: gadget: udc: fix spin_lock in pch_udc") Signed-off-by: Iago Abal <mail@iagoabal.eu> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Baolin Wang [Mon, 16 May 2016 08:43:53 +0000 (16:43 +0800)]
dwc3: gadget: Implement the suspend entry event handler
It had changed to be suspend event for BIT6 in DEVT register from
version 2.30a and above. Thus this patch introduces one suspend
event handler to handle the suspend event.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Arnd Bergmann [Wed, 18 May 2016 21:24:06 +0000 (23:24 +0200)]
usb: phy: move msm_hsusb.h into driver
As a preparation for another cleanup, this moves the header file
for the phy-msm-usb driver into the driver itself. No other file
includes it any more, and we don't really want it in the global
namespace anyway.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
usb: gadget: f_fs: buffer data from ‘oversized’ OUT requests
f_fs rounds up read(2) requests to a multiple of a max packet size
which means that host may provide more data than user has space for.
So far, the excess data has been silently ignored.
This introduces a buffer for a tail of such requests so that they are
returned on next read instead of being ignored.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
usb: gadget: f_fs: printk error when excess data is dropped on read
Add a pr_err when host sent more data then the size of the buffer user
space gave us. This may happen on UDCs which require OUT requests to
be aligned to max packet size. The patch includes a description of the
situation.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
drivers/usb/gadget/udc/mv_u3d_core.c: In function ‘mv_u3d_process_ep_req’:
drivers/usb/gadget/udc/mv_u3d_core.c:124:6: warning: variable ‘trb_complete’ set but not used [-Wunused-but-set-variable]
int trb_complete, actual, remaining_length = 0;
^
drivers/usb/gadget/udc/mv_u3d_core.c:123:28: warning: variable ‘curr_ep_context’ set but not used [-Wunused-but-set-variable]
struct mv_u3d_ep_context *curr_ep_context;
^
drivers/usb/gadget/udc/mv_u3d_core.c:122:13: warning: variable ‘cur_deq_lo’ set but not used [-Wunused-but-set-variable]
dma_addr_t cur_deq_lo;
^
drivers/usb/gadget/udc/mv_u3d_core.c: In function ‘mv_u3d_ep_enable’:
drivers/usb/gadget/udc/mv_u3d_core.c:530:28: warning: variable ‘ep_context’ set but not used [-Wunused-but-set-variable]
struct mv_u3d_ep_context *ep_context;
^
drivers/usb/gadget/udc/mv_u3d_core.c: In function ‘mv_u3d_ep_disable’:
drivers/usb/gadget/udc/mv_u3d_core.c:636:28: warning: variable ‘ep_context’ set but not used [-Wunused-but-set-variable]
struct mv_u3d_ep_context *ep_context;
^
In doing so, it removes calls to ioread32 function which does I/O with
the device, but I hope the reads don’t have any side effects that are
needed.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
drivers/usb/gadget/udc/r8a66597-udc.c: In function ‘r8a66597_irq’:
drivers/usb/gadget/udc/r8a66597-udc.c:1468:15: warning: variable ‘nrdyenb’ set but not used [-Wunused-but-set-variable]
u16 brdyenb, nrdyenb, bempenb;
^
drivers/usb/gadget/udc/r8a66597-udc.c:1467:15: warning: variable ‘nrdysts’ set but not used [-Wunused-but-set-variable]
u16 brdysts, nrdysts, bempsts;
^
In doing so, it removes calls to r8a66597_read function which does I/O
with the device, but I hope the reads don’t have any side effects that
are needed.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
drivers/usb/gadget/udc/m66592-udc.c: In function ‘m66592_irq’:
drivers/usb/gadget/udc/m66592-udc.c:1203:15: warning: variable ‘nrdyenb’ set but not used [-Wunused-but-set-variable]
u16 brdyenb, nrdyenb, bempenb;
^
drivers/usb/gadget/udc/m66592-udc.c:1202:15: warning: variable ‘nrdysts’ set but not used [-Wunused-but-set-variable]
u16 brdysts, nrdysts, bempsts;
^
In doing so, it removes calls to m66592_read function which does I/O
with the device, but I hope the reads don’t have any side effects that
are needed.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Maintain backward compatibility for a single named
interrupt ("dwc3_usb3") for all interrupts as well as
unnamed interrupt at index 0 for all interrupts.
As platform_get_irq() variants are used, tackle
the -EPROBE_DEFER case as well.
Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Hans de Goede [Fri, 10 Jun 2016 09:46:25 +0000 (11:46 +0200)]
USB: Fix of_usb_get_dr_mode_by_phy with a shared phy block
Some SoCs have a single phy-hw-block with multiple phys, this is
modelled by a single phy dts node, so we end up with multiple
controller nodes with a phys property pointing to the phy-node
of the otg-phy.
Only one of these controllers typically is an otg controller, yet we
were checking the first controller who uses a phy from the block and
then end up looking for a dr_mode property in e.g. the ehci controller.
This commit fixes this by adding an arg0 parameter to
of_usb_get_dr_mode_by_phy and make of_usb_get_dr_mode_by_phy
check that this matches the phandle args[0] value when looking for
the otg controller.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Done fixes and tested hsotg gadget's BDMA mode. Tested Control,
Bulk, Isoc, Inter transfers. Added code for isoc transfers,
removed unusable code, done minor fixes. Affected functions
and IRQ handlers:
- dwc2_hsotg_start_req(),
- dwc2_hsotg_ep_enable(),
- dwc2_hsotg_ep_queue(),
- dwc2_hsotg_handle_outdone(),
- GINTSTS_GOUTNAKEFF handler,
Removed 'has_correct_parity' flag from 'dwc2_hsotg_ep' struct.
Before this patch series, to set the data pid the DWC2 gadget
driver was toggling the even/odd until it match, then were
leaving it set. But now I have added mechanism to set pid and
excluded all code where this flag was set.
Tested-by: John Keeping <john@metanate.com> Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com> Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
usb: dwc2: gadget: Add EP disabled interrupt handler
Reimplemented EP disabled interrupt handler and moved to
corresponding function.
This interrupt indicates that the endpoint has been disabled per
the application's request.
For IN endpoints flushes txfifo, in case of BULK clears DCTL_CGNPINNAK,
in case of ISOC completes current request.
For ISOC-OUT endpoints completes expired requests. If there is
remaining request starts it. This is the part of ISOC-OUT transfer
drop flow. When ISOC-OUT transfer expired we must disable ep to drop
ongoing transfer.
Tested-by: John Keeping <john@metanate.com> Reviewed-by: Vahram Aharonyan <vahrama@synopsys.com> Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com> Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
usb: dwc2: gadget: Add Incomplete ISO IN/OUT Interrupt handlers
Incomplete ISO IN interrupt indicates one of the following conditions
occurred while transmitting an ISOC transaction.
- Corrupted IN Token for ISOC EP.
- Packet not complete in FIFO.
Incomplete ISO OUT indicates that there is at least one isochronous OUT
endpoint on which the transfer is not completed in the current
microframe.
The following actions will be taken:
In case of EP-IN
- Determine the EP
- Disable EP directly from this handler; when "Endpoint Disabled"
interrupt is received flush FIFO
In case of EP-OUT
- Determine the EP
- If target frame elapsed set DCTL_SGOUTNAK, unmask GOUTNAKEFF and
proceed as described in section 7.5.1 of DWC-HSOTG Programming Guide
Also added dwc2_gadget_target_frame_elapsed() helper function which
will be used in Incomplete ISO IN/OUT Interrupt handlers.
Tested-by: John Keeping <john@metanate.com> Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com> Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
usb: dwc2: gadget: Add OUTTKNEPDIS and NAKINTRPT handlers
NAKINTRPT interrupt is starting point for isoc-in transfer,
synchronization done with first in token received from host,
core asserts this interrupt when responds with 0 length data
to in token, received from host.
The first IN token is asynchronous for device - device does not
know when first one token will arrive from host. On first token
arrival HW generates 2 interrupts: 'in token received while FIFO
empty' and 'NAK'. NAK interrupt for ISOC in means that token has
arrived and ZLP was sent in response to that as there was no data
in FIFO. SW is basing on this interrupt to obtain frame in which
token has come and then based on the interval calculates next
frame for transfer.
OUTTKNEPDIS interrupt is starting point for isoc-out transfer,
synchronization done with first out token received from host
while corresponding ep is disabled.
For OUTs the reason is same - device does not know initial frame
in which out token will come. For this HW generates OUTTKNEPDIS
- out token is received while EP is disabled. Upon getting this
interrupt SW starts calculation for next transfer frame.
Tested-by: John Keeping <john@metanate.com> Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com> Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Increases and checks targeted frame number of current ep
if overrun happened, sets flag and masks with DSTS_SOFFN_LIMIT
Added following fields to struct dwc2_hsotg_ep
-target_frame: Targeted frame num to setup next ISOC transfer
-frame_overrun: Indicates SOF number overrun in DSTS
Tested-by: John Keeping <john@metanate.com> Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com> Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
usb: dwc2: gadget: Fix transfer stop programming for out endpoint
According DWC-OTG databook, "GOUTNakEff" is read only and can be
cleared only by "DCTL.CGOUTNak", but here we do not need to clear
it because DWC-OTG programming guide says that before disabling
any OUT endpoint, the application must enable Global OUT NAK mode,
so if this mode is enabled we can continue without this step.
Tested-by: John Keeping <john@metanate.com> Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com> Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Arnd Bergmann [Thu, 16 Jun 2016 11:38:25 +0000 (13:38 +0200)]
usb: pxa27x_udc: remove unused function argument
We get a warning for this when building with W=1 because the
argument gets assigned to something else but never read:
drivers/usb/gadget/udc/pxa27x_udc.c: In function 'stop_activity':
drivers/usb/gadget/udc/pxa27x_udc.c:1828:74: error: parameter 'driver' set but not used [-Werror=unused-but-set-parameter]
This remove the argument entirely.
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Baolin Wang [Mon, 20 Jun 2016 08:19:48 +0000 (16:19 +0800)]
usb: dwc3: gadget: Add the suspend state checking when stopping gadget
It will be crash to stop gadget when the dwc3 device had been into suspend
state, thus we need to check if the dwc3 device had been into suspend state
when UDC try to stop gadget.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Felipe Balbi [Tue, 21 Jun 2016 07:32:02 +0000 (10:32 +0300)]
usb: dwc3: gadget: issue ENDTRANSFER conditional on resource_index
Because of recent changes to transfer handling on
DWC3, we will not get XferComplete unless we
completely fill up our TRB ring. This means that we
might get a Reset or Disconnect without getting a
XferComplete first.
In order to correctly release our allocated Transfer
Resource, we must issue ENDTRANSFER command whenever
dep->resource_index is valid.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
it's clear now that when is_on=true, we must loop
until DWC3_DSTS_DEVCTRLHLT clears; while when
is_on=false we must loop until DWC3_DSTS_DEVCTRLHLT
gets set.
Instead of adding actual if() statements, we can
rely on XOR operation to evaluate to true only when
the above conditions apply. Then, we can move the
break condition back to the while() statement
together with our timeout check and the resulting
code is very compact and simpler to read.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Felipe Balbi [Thu, 9 Jun 2016 13:24:08 +0000 (16:24 +0300)]
usb: dwc3: gadget: remove udelay() from run_stop()
testing shows that udelay() is unnecessary as
controller reaches Halted state almost
instantenously as can be seen by our timeout
variable never actually decrementing.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Felipe Balbi [Tue, 7 Jun 2016 09:49:52 +0000 (12:49 +0300)]
usb: dwc3: pci: add dr-mode for Intel dwc3
It's know that Intel's SoCs' dwc3 integration is
peripheral-only since Intel implements its own
portmux for role-swapping. In order to prevent dwc3
from ever registering and XHCI platform_device,
let's just set dr-mode to peripheral-only on Intel
SoCs.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Felipe Balbi [Tue, 31 May 2016 10:39:21 +0000 (13:39 +0300)]
usb: gadget: add tracepoints to the gadget API
This new set of tracepoints will help all gadget
drivers and UDC drivers when problem appears. Note
that, in order to be able to add tracepoints to
udc-core.c we had to rename that to core.c and
statically link it with trace.c to form
udc-core.o. This is to make sure that module name
stays the same.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Felipe Balbi [Tue, 31 May 2016 10:07:47 +0000 (13:07 +0300)]
usb: gadget: move gadget API functions to udc-core
instead of defining all functions as static inlines,
let's move them to udc-core and export them with
EXPORT_SYMBOL_GPL, that way we can make sure that
only GPL drivers will use them.
As a side effect, it'll be nicer to add tracepoints
to the gadget API.
While at that, also fix Kconfig dependencies to
avoid randconfig build failures.
Acked-By: Sebastian Reichel <sre@kernel.org> Acked-by: Peter Chen <peter.chen@nxp.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Felipe Balbi [Mon, 30 May 2016 10:41:22 +0000 (13:41 +0300)]
usb: dwc3: gadget: start Bulk endpoints more frequently
Now we can try to issue Update Transfer every time
gadget driver queues a new request. This will make
sure we keep controller's queue busy for as long as
possible.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Felipe Balbi [Mon, 30 May 2016 10:38:32 +0000 (13:38 +0300)]
usb: dwc3: gadget: use allocated/queued reqs for LST bit
Let's only set LST bit when we run out of space in
our TRB ring. For all other cases, we keep LST bit
unset which will prevent constant allocation and
deallocation of endpoint transfer resources.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Heikki Krogerus [Fri, 22 Apr 2016 08:17:40 +0000 (11:17 +0300)]
usb: dwc3: remove handling of platform data
No more users for it.
Tested-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Heikki Krogerus [Fri, 22 Apr 2016 08:17:39 +0000 (11:17 +0300)]
usb: dwc3: pci: use build-in properties instead of platform data
This should allow the core driver to drop handling of
platform data and expect the platform specific details to
always come from properties.
Tested-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Cc: Huang Rui <ray.huang@amd.com> CC: John Youn <John.Youn@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
"Because PIPE powerpresent has a different meaning in host and in device mode,
and because of the redundancy with the UTMI signals, the controller ORes
together the appropriate PIPE and UTMI inputs to create its internal
VBUS status. For that reason, it is recommended to leave field
USBOTGSS_UTMI_OTG_STATUS[9] POWERPRESENT at its default value (=0), and only to
fill in the USB2 VBUS status fields in the same register."
Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
William Wu [Fri, 13 May 2016 10:13:46 +0000 (18:13 +0800)]
usb: dwc3: add DWC3_GUCTL1 reg for debug
GUCTL1 reg has some useful functions which can be
written by user. For rockchip platform, we set
GUCTL1.DEV_FORCE_20_CLK_FOR_30_CLK (bit26, applicable
for the core is programmed to operate in 2.0 device
only) to 1 in bootrom, and after start the kernel,
we want to check whether this bit can be reset to
default 0 after the core reset. Dump GUCTL1 reg from
debugfs is more convenient for us.
Signed-off-by: William Wu <william.wu@rock-chips.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
John Youn [Mon, 23 May 2016 18:32:45 +0000 (11:32 -0700)]
usb: dwc3: gadget: Fix truncated cast issue
From sparse:
warning: cast truncates bits from constant value (100 becomes 0)
The DWC3_TRB_NUM constant is too big for u8. Do the calculation a
slightly different way that should still be optimized out for the case
where DWC3_TRB_NUM == 256.
Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
John Youn [Fri, 20 May 2016 00:26:17 +0000 (17:26 -0700)]
usb: dwc3: gadget: Handle TRB index 0 when full or empty
If the trb->enqueue == trb->dequeue, then it could be full or empty.
This could also happen at TRB index 0, so modify the check to handle
that condition. At index 0, the previous TRB is the one just before the
link TRB.
Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
John Youn [Fri, 20 May 2016 00:26:05 +0000 (17:26 -0700)]
usb: dwc3: gadget: Simplify skipping of link TRBs
Make the skipping of the link TRBS built-in to the increment operation.
This simplifies the code wherever we increment the trb index and ensures
that we never end up pointing to a link trb.
Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
projects / linux-beck.git / log