Paul Mundt [Tue, 15 May 2007 08:41:02 +0000 (01:41 -0700)]
nommu: add ioremap_page_range()
lib/ioremap.c is presently only built in if CONFIG_MMU is set. While this
is reasonable, platforms that support both CONFIG_MMU=y or n need to be
able to call in to this regardless.
As none of the current nommu platforms do anything special with ioremap(),
we assume that it's always successful.
This fixes the SH-4 build with CONFIG_MMU=n.
Signed-off-by: Paul Mundt <lethal@linux-sh.org> Cc: David Howells <dhowells@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Davide Libenzi [Tue, 15 May 2007 08:40:47 +0000 (01:40 -0700)]
epoll locks changes and cleanups
Changes the rwlock to a spinlock, and drops the use-count variable.
Operations are always bound by the mutex now, so the use-count is no more
needed. For the same reason, the rwlock can become a simple spinlock.
Davide Libenzi [Tue, 15 May 2007 08:40:41 +0000 (01:40 -0700)]
fix epoll single pass code and add wait-exclusive flag
Fixes the epoll single pass code. During the unlocked event delivery (to
userspace) code, the poll callback can re-issue new events, and we must
receive them correctly. Since we loop in a lockless fashion, we want to be
O(nready), and we don't want to flash on/off the spinlock for every event, we
have the poll callback to use a secondary list to queue events while we're
inside the event delivery loop. The rw_semaphore has been turned into a
mutex. This patch also adds the wait-exclusive flag, as suggested by Davi
Arnaut.
Andi Kleen is unhappy with the changes, and they really do not seem
worth it. IPMI could use DIE_NMI_IPI instead of the new callback, even
though that ends up having its own set of problems too, mainly because
the IPMI code cannot really know the NMI was from IPMI or not.
Manually fix up conflicts in arch/x86_64/kernel/traps.c and
drivers/char/ipmi/ipmi_watchdog.c.
Linus Torvalds [Mon, 14 May 2007 19:29:14 +0000 (12:29 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc:
pxamci: fix PXA27x MMC workaround for bad CRC with 136 bit response
mmc: use assigned major for block device
sdhci: handle dma boundary interrupts
mmc: au1xmmc command types check from data flags
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[IPV4] SNMP: Display new statistics at /proc/net/netstat
[IPV6]: Reverse sense of promisc tests in ip6_mc_input
[NET_SCHED]: prio qdisc boundary condition
[IPSEC]: Don't warn if high-order hash resize fails
[IPSEC]: Check validity of direction in xfrm_policy_byid
* master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SPARC64]: Update defconfig.
[VIDEO]: XVR-500 and XVR-2500 need FB=y.
[SPARC32]: asm/system.h needs asm/smp.h
[SPARC32]: Update defconfig.
[SPARC32]: Fix sparc32 kdebug changes.
[SPARC64]: Accept ebus_bus_type for generic DMA ops.
[SPARC64]: Add missing cpus_empty() check in hypervisor xcall handling.
[SCSI]: Add help text for SCSI_ESP_CORE.
[SPARC] SBUS: display7seg.c needs asm/io.h
[SPARC] SBUS: bbc_i2c.c needs asm/io.h
[SPARC64]: Be more resiliant with PCI I/O space regs.
[SERIAL] SUNHV: Add an ID string.
Dave Jones [Sun, 13 May 2007 23:07:46 +0000 (19:07 -0400)]
MAINTAINERS update.
I've not really 'maintained' this code for years, and others
are doing a much more thorough job these days.
Removing myself might stem some of the crazier emails I get.
Signed-off-by: Dave Jones <davej@redhat.com> Acked-by: H. Peter Anvin <hpa@zytor.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Thomas Gleixner [Mon, 14 May 2007 09:10:02 +0000 (11:10 +0200)]
timekeeping fix patch got mis-applied
The time keeping code move to kernel/time/timekeeping.c broke the
clocksource resume logic patch, which got applied to the old file by a
fuzzy application. Fix it up and move the clocksource_resume() call to
the appropriate place.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
[ tssk, tssk, everybody should use --fuzz=0 ] Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pierre Ossman [Sun, 13 May 2007 20:39:23 +0000 (22:39 +0200)]
sdhci: handle dma boundary interrupts
When the device hits certain memory boundaries, it signals an
interrupt and expects to be serviced. We don't need the feature
but we need to make sure the device doesn't stall.
Mitsuru Chinen [Mon, 14 May 2007 10:07:30 +0000 (03:07 -0700)]
[IPV4] SNMP: Display new statistics at /proc/net/netstat
This displays the statistics specified in the updated IP-MIB RFC
(RFC4293) in /proc/net/netstat. The reason why these are not displayed
in /proc/net/snmp is that some existing utilities are developed under
the assumption which ipstat items in /proc/net/snmp is unchanged.
Signed-off-by: Mitsuru Chinen <mitch@linux.vnet.ibm.com> Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Corey Mutter [Mon, 14 May 2007 10:00:27 +0000 (03:00 -0700)]
[IPV6]: Reverse sense of promisc tests in ip6_mc_input
Reverse the sense of the promiscuous-mode tests in ip6_mc_input().
Signed-off-by: Corey Mutter <crm-netdev@mutternet.com> Signed-off-by: David L Stevens <dlstevens@us.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Mon, 14 May 2007 09:15:47 +0000 (02:15 -0700)]
[IPSEC]: Check validity of direction in xfrm_policy_byid
The function xfrm_policy_byid takes a dir argument but finds the policy
using the index instead. We only use the dir argument to update the
policy count for that direction. Since the user can supply any value
for dir, this can corrupt our policy count.
I know this is the problem because a few days ago I was deleting
policies by hand using indicies and accidentally typed in the wrong
direction. It still deleted the policy and at the time I thought
that was cool. In retrospect it isn't such a good idea :)
I decided against letting it delete the policy anyway just in case
we ever remove the connection between indicies and direction.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Al Viro [Sun, 13 May 2007 09:52:32 +0000 (05:52 -0400)]
fix deadlock in loop.c
... doh
Jeremy Fitzhardinge noted that the recent loop.c cleanups worked, but
cause lockdep to complain.
Ouch. OK, the deadlock is real and yes, I'm an idiot. Speaking of which,
we probably want to s/lock/pin/ in drivers/base/map.c to avoid such
brainos again. And yes, this stuff needs clear documentation. Will try
to put one together once I get some sleep...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
SLUB cannot run on i386 at this point because i386 uses the page->private and
page->index field of slab pages for the pgd cache.
Make SLUB run on i386 by replacing the pgd slab cache with a quicklist.
Limit the changes as much as possible. Leave the improvised linked list in place
etc etc. This has been working here for a couple of weeks now.
Acked-by: William Lee Irwin III <wli@holomorphy.com> Signed-off-by: Christoph Lameter <clameter@sgi.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Christian Krafft [Sat, 12 May 2007 17:37:01 +0000 (10:37 -0700)]
IPMI: Add PPC openfirmware unregister
When trying to load the ipmi_si module on a powerpc with no BMC (baseboard
management controller) the driver failes to load correctly, but doesn't
unregister itself from of_platform. So, on a second modprobe the kernel
crashes. This patch adds the missing unregister call.
Signed-off-by: Christian Krafft <krafft@de.ibm.com> Signed-off-by: Corey Minyard <minyard@acm.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Paul Fulghum [Sat, 12 May 2007 17:36:55 +0000 (10:36 -0700)]
tty: flush flip buffer on ldisc input queue flush
Flush the tty flip buffer when the line discipline input queue is flushed,
including the user call tcflush(TCIFLUSH/TCIOFLUSH). This prevents
unexpected stale data after a user application calls tcflush().
Signed-off-by: Alan Cox <alan@redhat.com> Cc: Antonino Ingargiola <tritemio@gmail.com> Signed-off-by: Paul Fulghum <paulkf@microgate.com> Cc: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andi Kleen [Sat, 12 May 2007 15:27:40 +0000 (17:27 +0200)]
x86_64: Add asm/mtrr.h include for some builds
The earlier change to call the bp mtrr init from bugs.c broke
on some configurations due to missing includes. Noticed
by "Avuton Olrich" <avuton@gmail.com>
Dale Farnsworth [Sat, 12 May 2007 00:58:43 +0000 (10:58 +1000)]
[POWERPC] Add arch/powerpc support for the Motorola PrPMC2800
This finally adds the PPC_PRPMC2800 Kconfig option, the board setup
code (the setup and reset functions) and the defconfig, to support the
Motorola PrPMC2800 platform.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Mark A. Greer [Sat, 12 May 2007 00:58:18 +0000 (10:58 +1000)]
[POWERPC] Add bootwrapper support for Motorola PrPMC2800 platform
The Motorola PrPMC280 and PrPMC2800 processor modules sit on an F101 or
PrPMC2800 baseboard, respectively. There are several variants of each
type of processor module which can have different amounts of memory,
amounts of FLASH, cpu frequencies, and an mv64360 or an mv64362.
The bootwrapper code for that platform reads VPD from an I2C EEPROM
to determine the processor module variant. From the variant, the
amount of memory, etc. is determined and the device tree is updated
accordingly. If the variant cannot be determined (e.g., corrupted
VPD or a previously unknown variant), the property values already
in the device tree are used.
Also, the firmware for those platforms does not completely configure
the mv64x60 host bridge so that configuration is done here.
Signed-off-by: Mark A. Greer <mgreer@mvista.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
Mark A. Greer [Sat, 12 May 2007 00:57:58 +0000 (10:57 +1000)]
[POWERPC] Add DTS file for the Motorola PrPMC2800 platform
Add the device tree source file for the prpmc2800 line of processor PMCs.
Several of the property values are updated by the bootwrapper but sane
defaults have been chosen in case the bootwrapper can't determine the
exact processor board variant. The defaults should allow the kernel
to boot despite having non-optimal device tree property values.
Signed-off-by: Mark A. Greer <mgreer@mvista.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
Dale Farnsworth [Sat, 12 May 2007 00:57:35 +0000 (10:57 +1000)]
[POWERPC] Check cache coherency of kernel vs firmware
check_cache_coherency() verifies that the cache coherency setting of
the kernel (CONFIG_NOT_COHERENT_CACHE) matches that left by the firmware,
as indicated by coherency-off device tree property.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Dale Farnsworth [Sat, 12 May 2007 00:57:12 +0000 (10:57 +1000)]
[POWERPC] Add Marvell mv64x60 PCI bridge support
This patch adds PCI bridge support for the Marvell mv64x60 chip.
We also provide the ability to read/write the mv64x60 hotswap
register via sysfs if the hs_reg_valid property is set in the
device tree.
This patch creates platform_device entries for the Marvell mv64x60
I2C ports, based on information contained in device tree.
This driver (like the other mv64x60 drivers) are unusual in that it
works on both the MIPS and PowerPC architectures. Because of that,
the drivers do not support the normal PowerPC of_platform_bus_type.
They support platform_bus_type instead.
This patch creates platform_device entries for the Marvell mv64x60
ethernet controller ports, based on information contained in the
device tree.
This driver (like the other mv64x60 drivers) are unusual in that it
works on both the MIPS and PowerPC architectures. Because of that,
the drivers do not support the normal PowerPC of_platform_bus_type.
They support platform_bus_type instead.
This patch creates platform_device entries for the Marvell mv64x60
MPSC (multi-protocol serial controller) ports, based on information
contained in the device tree.
This driver (like the other mv64x60 drivers) are unusual in that it
works on both the MIPS and PowerPC architectures. Because of that,
the drivers do not support the normal PowerPC of_platform_bus_type.
They support platform_bus_type instead.
Dale Farnsworth [Sat, 12 May 2007 00:55:24 +0000 (10:55 +1000)]
[POWERPC] Add interrupt support for Marvell mv64x60 chips
There are 3 interrupt groups each with its own status/mask registers.
We use a separate struct irq_chip for each interrupt group and handle
interrupts in two stages or levels: level 1 selects the appropriate
struct irq_chip, and level 2 selects individual interrupts within
that irq_chip.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Mark A. Greer [Sat, 12 May 2007 00:54:53 +0000 (10:54 +1000)]
[POWERPC] Add bootwrapper support for Marvell/mv64x60 I2C
Some platforms support a variety processor modules with no method of
determining which exact processor module is being used except by
examining Vital Product Data (VPD). The modules may have different
amounts of memory, clock frequencies, etc. so reading the VPD becomes
necessary to correctly set properties in the device tree before its
passed to the kernel.
Often the VPD is stored in I2C EEPROMs so an I2C driver becomes necessary.
This I2C driver is for the I2C controller that's embedded on the Marvel
mv64x60 line of host bridges.
Signed-off-by: Mark A. Greer <mgreer@mvista.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
Mark A. Greer [Sat, 12 May 2007 00:54:31 +0000 (10:54 +1000)]
[POWERPC] Add bootwrapper support for Marvell MPSC
The bootwrapper requires a serial driver to allow cmdline editing
and information reporting on the console. This driver is required
by platforms that boot a zImage and use the MPSC for the console.
Signed-off-by: Mark A. Greer <mgreer@mvista.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
Mark A. Greer [Sat, 12 May 2007 00:54:05 +0000 (10:54 +1000)]
[POWERPC] Add bootwrapper support for Marvell/mv64x60 hostbridge
The mv64x60 host bridge has many windows between its various components
(cpu, system memory, ethernet ctlr, MPSC, DMA ctlr, PCI MEM, PCI I/O).
Unfortunately, the firmware on some of mv64x60-based platforms do not
properly or completely configure those windows (e.g., MPSC->system memory
windows not configured or CPU->PCI MEM space not configured).
So, the missing configuration needs to be done in either the bootwrapper
or in the kernel. To keep the kernel as clean as possible, it is done
in the bootwrapper. Note that I/O controller configuration is NOT being
done, its only the windows to allow the I/O controllers and other components
to access memory, etc. that is being done--drivers assume that their
controllers can already access system memory).
Table of routines and the windows they configure:
mv64x60_config_ctlr_windows() ENET->System Memory
MPSC->System Memory
IDMA->System Memory
Mark A. Greer [Sat, 12 May 2007 00:53:36 +0000 (10:53 +1000)]
[POWERPC] Add Makefile rules to wrap dts file in zImage
Add 'zImage.dts' and 'zImage.dts_initrd' build rules that automatically
compile and wrap a dts file from arch/powerpc/boot/dts into the zImage file.
The resulting zImage will be arch/powerpc/boot/zImage.dts.<platform> and
arch/powerpc/boot/zImage.dts_initrd.<platform>, respectively.
Having separate rules allows the user to choose whether to include a device
tree--and which device tree--at build time. This is useful when one Makefile
target builds a zImage that runs on several platforms except for differing
device trees. By just setting CONFIG_DEVICE_TREE and running "make zImage.dts"
the exact zImage you want is built without Makefile bloat or manually running
the wrapper script.
The dts file is expected to be arch/powerpc/boot/dts/$(CONFIG_DEVICE_TREE)
Signed-off-by: Mark A. Greer <mgreer@mvista.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
Scott Wood [Fri, 11 May 2007 17:52:03 +0000 (03:52 +1000)]
[POWERPC] U-boot passes the initrd as start/end, not start/size.
The boot wrapper platform init code on 83xx and 85xx using the cuboot
platform type was incorrectly assuming that u-boot supplied the size
of the initrd, whereas it actually supplies the end address. This
fixes it.
Signed-off-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
will schmidt [Fri, 11 May 2007 13:34:16 +0000 (23:34 +1000)]
[POWERPC] Simplify smp_space_timers
Greatly simplify the function smp_space_timers.
The stolen time calculation (per comment within the code) doesn't need the
half-jiffy stagger any more. There isn't an issue with bouncing off global
locks, so we really shouldn't need any sort of staggering at all.
However, the last_jiffy value still needs to be set. This removes the
extra stagger logic, and just sets the values.
This change should benefit applications that rely on barrier
synchronization, and will help cut down OS jitter.
Boot tested across the board (G5,power3,power4,power5,970mp blade).
Signed-off-by: Will Schmidt <will_schmidt@vnet.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
Stephen Rothwell [Fri, 11 May 2007 05:42:44 +0000 (15:42 +1000)]
[POWERPC] Trivial ps3 warning fixes
Fixes warnings:
arch/powerpc/platforms/ps3/system-bus.c: In function 'ps3_map_sg':
arch/powerpc/platforms/ps3/system-bus.c:278: warning: unused variable 'i'
arch/powerpc/platforms/ps3/system-bus.c:277: warning: unused variable 'dev'
arch/powerpc/platforms/ps3/setup.c:103: warning: 'prealloc' defined but not used
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Acked-by: Geoff Levand <geoffrey.levand@am.sony.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
Stephen Rothwell [Fri, 11 May 2007 05:40:36 +0000 (15:40 +1000)]
[POWERPC] Add missed include
fixes:
arch/powerpc/platforms/pasemi/idle.c: In function 'pasemi_system_reset_exception':
arch/powerpc/platforms/pasemi/idle.c:55: warning: implicit declaration of function 'do_IRQ'
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
Linus Torvalds [Fri, 11 May 2007 23:03:03 +0000 (16:03 -0700)]
Merge branch 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
pata_platform: don't use generic ata_port_start
Use menuconfig objects: libata
add the ATI SB700 SATA controller device id to AHCI pci table
Add the combined mode for ATI SB700
pata_pcmcia: recognize 2GB CompactFlash from Transcend
git-libata-all: sata_via build fix
libata-acpi: clean up parameters and misc stuff
libata-acpi: s/CONFIG_SATA_ACPI/CONFIG_ATA_ACPI/
libata: give devices one last chance even if recovery failed with -EINVAL
libata: fallback to the other IDENTIFY on device error, take#2
libata: ignore EH scheduling during initialization
libata: clean up SFF init mess
libata: implement libata.spindown_compat
libata: reimplement suspend/resume support using sdev->manage_start_stop
Linus Torvalds [Fri, 11 May 2007 23:02:05 +0000 (16:02 -0700)]
Merge branch 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6: (35 commits)
Add support for the Davicom DM9161A PHY
sky2: only disable 88e8056 on some boards
sky2: 88e8071 support not ready
skge: crash on shutdown/suspend
sky2: fix oops on shutdown
mlx4: don't use deprecated IRQ flags
netxen_nic_main don't use deprecated irq flags
Use menuconfig objects II - netdev/wan
Use menuconfig objects II - netdev/pcmcia
Use menuconfig objects II - netdev/atm
Use menuconfig objects: netdev
Use menuconfig objects: PHY
spidernet: remove unnecessary accesses to phy
S2IO: Statistics for link up/down and memory allocated/freed
S2IO: statistics for memory allocation failuers
S2IO: getringparam ethtool option
[PATCH] libertas: 64-bit cleanups
[PATCH] libertas: sparse fixes
[PATCH] libertas: fix missing unlock in TX error path
[PATCH] libertas: make debugfs.c sparse-clean
...
David Miller [Fri, 11 May 2007 20:26:44 +0000 (13:26 -0700)]
Fix assertion failure with MSI on sparc64
Today's find is a triggered assertion in msi_free_irqs() when the system
doesn't support MSI, in which case arch_setup_msi_irqs() always returns
an error.
The problem is that when this happens we branch into msi_free_irqs(), to
which you added the following assertion loop:
Well, if arch_setup_msi_irqs() fails, entry->irq will be zero and
although that's never assigned to any normal devices we use that IRQ
number for the timer interrupt on sparc64 so this assertion triggers.
Better to test for zero before doing the irq_has_action() assertion
thing.
Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Olof Johansson [Thu, 10 May 2007 04:00:20 +0000 (23:00 -0500)]
pata_platform: don't use generic ata_port_start
I have a system where I have a simple IDE controller that sits on a
local bus without bus master dma capability, and thus no dma_mapping
ops defined for the device/bus.
pata_platform works great for me, with the exception of using the generic
ata_port_start which tries to do a dmam_alloc_coherent.
Looks like it doesn't need to allocate a prd table at all, so replace it
with a dummy function instead.
Signed-off-by: Olof Johansson <olof@lixom.net> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Jan Engelhardt [Fri, 11 May 2007 05:48:54 +0000 (22:48 -0700)]
Use menuconfig objects: libata
Use menuconfigs instead of menus, so the whole menu can be disabled at once
instead of going through all options.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de> Cc: Jeff Garzik <jeff@garzik.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Henry Su [Fri, 11 May 2007 05:48:51 +0000 (22:48 -0700)]
add the ATI SB700 SATA controller device id to AHCI pci table
Add the device ID to AHCI pci table for ATI SB700 SATA controller, the
subsequent chipset of SB600.
Signed-off-by: henry su<henry.su@amd.com> Cc: Jeff Garzik <jeff@garzik.org> Cc: Tejun Heo <htejun@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Henry Su [Fri, 11 May 2007 05:48:50 +0000 (22:48 -0700)]
Add the combined mode for ATI SB700
Besides those modes in ATI SB600 SATA controller, ATI SB700 supports one
more mode:the combined mode.
The combined mode is a Legacy IDE mode used for compatibility with some old
OS without AHCI driver, but now it is not necessary for Linux since the
kernel has supported AHCI.
Signed-off-by: Luugi Marsan <luugi.marsan@amd.com> Cc: Jeff Garzik <jeff@garzik.org> Cc: Tejun Heo <htejun@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
projects / mv-sheeva.git / log