Change return code handling of the stsi() function:
In case function code 0 was specified the return value is the
current configuration level (already shifted). That way all
the code that actually copied the stsi_0() function can go
away.
Otherwise the return value is 0 (success) or negative to
indicate an error (currently only -EOPNOTSUPP).
Also stsi() is no longer an inline function. The function is
not performance critical, but every caller would generate an
exception table entry for this function.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
s390/exceptions: switch to relative exception table entries
This is the s390 port of 70627654 "x86, extable: Switch to relative
exception table entries".
Reduces the size of our exception tables by 50% on 64 bit builds.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
s390/sysinfo,topology: fix cpu topology maximum nesting detection
The maximum nesting of the cpu topology is evaluated when /proc/sysinfo
is the first time read. This happens without a lock and a concurrent
reader on a different cpu can see and use an invalid intermediate value.
Besides the fact that this race is quite unlikely the worst thing that
could happen is that /proc/sysinfo would contain bogus information about
the machine's cpu topology.
Nevertheless this should be fixed. So move the detection code to the
early machine detection code and since now the value is early available
use it in the topology code as well.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The current proc implementation of the /proc/sysinfo file writes all
informations contained in all system information blocks to a single
page.
This is done by calling sprintf all the time in the expectation that
everything will fit into a single page. This however is not necessarily
true if the configuration of a machine is very large.
So convert /proc/sysinfo to avoid writing into random memory regions.
For readability reasons a couple of lines are longer than 80 characters.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Any change to sysinfo.h causes a whole kernel recompile since sysinfo.h is
included by topology.h, which again is used nearly everywhere.
So remove that include and add a forward declaration instead.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Renaming the globally visible variable "user_mode" to "addressing_mode" in
order to fix a name clash was not a good idea. (Commit 37fe1d73 "s390/mm:
rename user_mode variable to addressing_mode")
Looking at the code after a couple of weeks one thinks: addressing mode of
what?
So rename the variable again. This time to s390_user_mode. Which hopefully
makes more sense.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Stefan Weinhuber [Fri, 31 Aug 2012 08:52:13 +0000 (10:52 +0200)]
s390/partitions: make partition detection independent from DASD ioctls
In some usage scenarios it is desireable to work with disk images or
virtualized DASD devices. One problem that prevents such applications
is the partition detection in ibm.c. Currently it works only for
devices that support the BIODASDINFO2 ioctl, in other words, it only
works for devices that belong to the DASD device driver.
The information gained from the BIODASDINFO2 ioctl is only for a small
set of legacy cases abolutely necessary. All current VOL1, LNX1 and
CMS1 type of disk labels can be interpreted correctly without this
information, as long as the generic HDIO_GETGEO ioctl works and
provides a correct disk geometry.
This patch makes the ibm.c partition detection as independent as
possible from the BIODASDINFO2 ioctl. Only the following two cases are
still restricted to real DASDs:
- An FBA DASD, or LDL formatted ECKD DASD without any disk label.
- An old style LNX1 label (without large volume support) on a disk
with inconsistent device geometry.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Heiko Carstens [Fri, 31 Aug 2012 11:35:25 +0000 (13:35 +0200)]
s390/mm: change default addressing mode
Change the default addressing mode so that user space runs in primary space
and the kernel runs in home space.
In addition remove the "switch_amode" kernel parameter so all users who
already specified they want the new default behaviour will stay in the
"switched" mode instead of in the opposite they intended.
If there is a need to switch addressing modes, this can be done with the
"user_mode" kernel parameter: user_mode=home
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Heiko Carstens [Thu, 30 Aug 2012 12:24:42 +0000 (14:24 +0200)]
s390/smp: avoid concurrent write to sigp status field
When a sigp instruction is issued it may store a status. This status is
currently stored in a per cpu field of the target cpu.
If multiple cpus issue a sigp instruction with the same target cpu
and a status is stored the result is not necessarily as expected.
Currently this is not an issue:
- on cpu hotplug no sigps, except "restart" and "sense" are sent to the
target cpu.
- on external call we don't look at the status if it is stored
- on sense running the condition code "status stored" is sufficient to
tell if a cpu is running or not
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Heiko Carstens [Wed, 29 Aug 2012 12:12:20 +0000 (14:12 +0200)]
s390/cache: add cpu cache information to /proc/cpuinfo
Add a line for each cpu cache to /proc/cpuinfo.
Since we only have information of private cpu caches in sysfs we
add a line for each cpu cache in /proc/cpuinfo which will also
contain information about shared caches.
Allow user-space processes to use transactional execution (TX).
If the TX facility is available user space programs can use
transactions for fine-grained serialization based on the data
objects that are referenced during a transaction. This is
useful for lockless data structures and speculative compiler
optimizations.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Jan Glauber [Tue, 31 Jul 2012 08:52:05 +0000 (10:52 +0200)]
s390: add support for runtime instrumentation
Allow user-space threads to use runtime instrumentation (RI). To enable RI
for a thread there is a new s390 specific system call, sys_s390_runtime_instr,
that takes as parameter a realtime signal number. If the RI facility is
available the system call sets up a control block for the calling thread with
the appropriate permissions for the thread to modify the control block.
The user-space thread can then use the store and modify RI instructions to
alter the control block and start/stop the instrumentation via RION/RIOFF.
If the user specified program buffer runs full RI triggers an external
interrupt. The external interrupt is translated to a real-time signal that
is delivered to the thread that enabled RI on that CPU. The number of
the real-time signal is the number specified in the RI system call. So,
user-space can select any available real-time signal number in case the
application itself uses real-time signals for other purposes.
The kernel saves the RI control blocks on task switch only if the running
thread was enabled for RI. Therefore, the performance impact on task switch
should be negligible if RI is not used.
RI is only enabled for user-space mode and is disabled for the supervisor
state.
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Holger Dengler [Tue, 28 Aug 2012 14:45:36 +0000 (16:45 +0200)]
s390/zcrypt: Separate msgtype implementation from card modules.
Msgtype implementations are now separated from card specific modules
and can be dynamically registered. Existing msgtype implementations
are restructured in modules.
Signed-off-by: Holger Dengler <hd@linux.vnet.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Holger Dengler [Tue, 28 Aug 2012 14:43:48 +0000 (16:43 +0200)]
s390/ap: Add functiton facility information as AP device attribute.
Add the function facility information as new ap_device and sysfs
attribute. Also make the number of requests in device
queue and in device driver queue accessible in sysfs.
Jan Glauber [Mon, 27 Aug 2012 08:55:18 +0000 (10:55 +0200)]
s390/kconfig: split the s390 base menu
Split the base menu into more descriptive categories like processor,
memory, etc. and move virtualization related entries to the
Virtualization menu.
Also select KEXEC unconditionally.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Heiko Carstens [Thu, 23 Aug 2012 14:31:13 +0000 (16:31 +0200)]
s390/cache: expose cpu cache topology via sysfs
Expose cpu cache topology via sysfs.
The created sysfs directory structure is compatible to what x86, ia64
and powerpc have.
On s390 we expose only information about cpu caches which are private
to a cpu via sysfs . Caches which are shared between cpus do not have
a sysfs representation.
The reason for that is that the file "shared_cpu_map" is mandatory
and only if running under LPAR it is possible to tell which cpus
share which cache. Second level hypervisors however do not and cannot
expose that information to guests.
In order to have a consistent view we made the choice to always only
expose information about private cpu caches via sysfs.
Example for a z196 cpu (cpu1 in /sys/devices/cpu):
Gerald Schaefer [Tue, 21 Aug 2012 10:36:34 +0000 (12:36 +0200)]
s390: enable large page support with CONFIG_DEBUG_PAGEALLOC
So far, large page support was completely disabled with
CONFIG_DEBUG_PAGEALLOC, although it would be sufficient if only the
large page kernel mapping was disabled. This patch enables large page
support with CONFIG_DEBUG_PAGEALLOC, while it prevents the large kernel
mapping in that case.
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Heiko Carstens [Tue, 14 Aug 2012 11:20:20 +0000 (13:20 +0200)]
s390/string: provide asm lib functions for memcpy and memcmp
Our memcpy and memcmp variants were implemented by calling the corresponding
gcc builtin variants.
However gcc is free to replace a call to __builtin_memcmp with a call to memcmp
which, when called, will result in an endless recursion within memcmp.
So let's provide asm variants and also fix the variants that are used for
uncompressing the kernel image.
In addition remove all other occurences of builtin function calls.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
1) Eric Dumazet discovered and fixed what turned out to be a family of
bugs. These functions were using pskb_may_pull() which might need
to reallocate the linear SKB data buffer, but the callers were not
expecting this possibility. The callers have cached pointers to the
packet header areas, and would need to reload them if we were to
continue using pskb_may_pull().
So they could end up reading garbage.
It's easier to just change these RAW4/RAW6/MIP6 routines to use
skb_header_pointer() instead of pskb_may_pull(), which won't modify
the linear SKB data area.
2) Dave Jone's syscall spammer caught a case where a non-TCP socket can
call down into the TCP keepalive code. The case basically involves
creating a raw socket with sk_protocol == IPPROTO_TCP, then calling
setsockopt(sock_fd, SO_KEEPALIVE, ...)
Fixed by Eric Dumazet.
3) Bluetooth devices do not get configured properly while being powered
on, resulting in always using legacy pairing instead of SSP. Fix
from Andrzej Kaczmarek.
4) Bluetooth cancels delayed work erroneously, put stricter checks in
place. From Andrei Emeltchenko.
5) Fix deadlock between cfg80211_mutex and reg_regdb_search_mutex in
cfg80211, from Luis R. Rodriguez.
6) Fix interrupt double release in iwlwifi, from Emmanuel Grumbach.
7) Missing module license in bcm87xx driver, from Peter Huewe.
8) Team driver can lose port changed events when adding devices to a
team, fix from Jiri Pirko.
9) Fix endless loop when trying ot unregister PPPOE device in zombie
state, from Xiaodong Xu.
10) batman-adv layer needs to set MAC address of software device
earlier, otherwise we call tt_local_add with it uninitialized.
11) Fix handling of KSZ8021 PHYs, it's matched currently by KS8051 but
that doesn't program the device properly. From Marek Vasut.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
ipv6: mip6: fix mip6_mh_filter()
ipv6: raw: fix icmpv6_filter()
net: guard tcp_set_keepalive() to tcp sockets
phy/micrel: Add missing header to micrel_phy.h
phy/micrel: Rename KS80xx to KSZ80xx
phy/micrel: Implement support for KSZ8021
batman-adv: Fix symmetry check / route flapping in multi interface setups
batman-adv: Fix change mac address of soft iface.
pppoe: drop PPPOX_ZOMBIEs in pppoe_release
team: send port changed when added
ipv4: raw: fix icmp_filter()
net/phy/bcm87xx: Add MODULE_LICENSE("GPL") to GPL driver
iwlwifi: don't double free the interrupt in failure path
cfg80211: fix possible circular lock on reg_regdb_search()
Bluetooth: Fix not removing power_off delayed work
Bluetooth: Fix freeing uninitialized delayed works
Bluetooth: mgmt: Fix enabling LE while powered off
Bluetooth: mgmt: Fix enabling SSP while powered off
Merge misc fixes from Andrew Morton:
"One maintainer change and three bugfixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (4 commits)
c/r: prctl: fix build error for no-MMU case
lib/flex_proportions.c: fix corruption of denominator in flexible proportions
checksyscalls: fix "here document" handling
pwm-backlight: take over maintenance
Mark Salter [Tue, 25 Sep 2012 00:17:38 +0000 (17:17 -0700)]
c/r: prctl: fix build error for no-MMU case
Commit 1ad75b9e1628 ("c/r: prctl: add minimal address test to
PR_SET_MM") added some address checking to prctl_set_mm() used by
checkpoint-restore. This causes a build error for no-MMU systems:
kernel/sys.c: In function 'prctl_set_mm':
kernel/sys.c:1868:34: error: 'mmap_min_addr' undeclared (first use in this function)
The test for mmap_min_addr doesn't make a lot of sense for no-MMU code
as noted in commit 6e1415467614 ("NOMMU: Optimise away the
{dac_,}mmap_min_addr tests").
This patch defines mmap_min_addr as 0UL in the no-MMU case so that the
compiler will optimize away tests for "addr < mmap_min_addr".
Signed-off-by: Mark Salter <msalter@redhat.com> Reviewed-by: Cyrill Gorcunov <gorcunov@openvz.org> Cc: <stable@vger.kernel.org> [3.6.x] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jan Kara [Tue, 25 Sep 2012 00:17:35 +0000 (17:17 -0700)]
lib/flex_proportions.c: fix corruption of denominator in flexible proportions
When racing with CPU hotplug, percpu_counter_sum() can return negative
values for the number of observed events.
This confuses fprop_new_period(), which uses unsigned type and as a
result number of events is set to big *positive* number. From that
moment on, things go pear shaped and can result e.g. in division by
zero as denominator is later truncated to 32-bits.
This bug causes a divide-by-zero oops in bdi_dirty_limit() in Borislav's
3.6.0-rc6 based kernel.
Fix the issue by using a signed type in fprop_new_period(). That makes
us bail out from the function without doing anything (mistakenly)
thinking there are no events to age. That makes aging somewhat
inaccurate but getting accurate data would be rather hard.
Signed-off-by: Jan Kara <jack@suse.cz> Reported-by: Borislav Petkov <bp@amd64.org> Reported-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com> Cc: Wu Fengguang <fengguang.wu@intel.com> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
"echo" doesn't read from stdin, therefore the checksyscalls script didn't
warn about not implemented system calls anymore since 29dc54c6
("checksyscalls: Use arch/x86/syscalls/syscall_32.tbl as source").
Use "cat" instead of "echo" which handles this correctly.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Michal Marek <mmarek@suse.cz> Cc: H. Peter Anvin <hpa@linux.intel.com> Cc: Cyrill Gorcunov <gorcunov@openvz.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Paul Mundt [Tue, 25 Sep 2012 02:51:05 +0000 (11:51 +0900)]
sh: pfc: Fix up GPIO mux type reconfig case.
Some drivers need to switch pin states between GPIO and pin function at
runtime, which was inadvertently broken in the pinctrl driver for GPIOs
being bound to a specific direction.
This fixes up the request path to ensure that previously configured GPIOs
don't cause us to inadvertently error out with an unsupported mux on
reconfig, which in practice is primarily aimed at trapping pull-up/down
users that have yet to be implemented under the new API.
Fixes up regressions in the TPU PWM driver, amongst others.
David S. Miller [Tue, 25 Sep 2012 02:00:00 +0000 (22:00 -0400)]
Merge branch 'for-davem' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless
John W. Linville says:
====================
Please pull this last(?) batch of fixes intended for 3.6...
For the Bluetooth bits, Gustavo says this:
"Here goes probably my last update to 3.6. It includes the two patches
you were ok last week(from Andrzej Kaczmarek), those are critical
ones, and two other fixes one for a system crash and the other for
a missing lockdep annotation."
The referenced fixes from Andrzej prevent attempts to configure devices
that are powered-off.
Along with the Bluetooth fixes, there are a couple of 802.11 fixes.
Emmanuel Grumbach gives us an iwlwifi fix to prevent releasing an
interrupt twice. Luis R. Rodriguez provides a fix for a possible
circular lock dependency in the cfg80211 regulatory enforcement code.
All of these have been in linux-next for a few days. I hope they are
not too late to make the 3.6 release!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull tile gxio ABI fix from Chris Metcalf:
"This fixes a last-minute change in the Tilera hypervisor ABI for TRIO
(PCI root complex) support. We've locked in this ABI going forward
and will make sure no further ABI changes like this occur."
* git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
tile: gxio iorpc numbering change for TRIO interface
Merge tag 'stable/for-linus-3.6-rc7-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull a Xen fix from Konrad Rzeszutek Wilk:
"It is a bug-fix when we run the initial PV guest on a AMD K8 machine
and have CONFIG_AMD_NUMA enabled and detect the NUMA topology from the
Northbridge.
We end up in the situation where the initial domain gets too much
information and gets confused and crashes - the fix is to restrict the
domain to get the information - and we do it by just disabling NUMA on
the PV guest (the hypervisor is still able to do its proper NUMA
allocations of guests).
It is OK to disable the PV guest from accessing NUMA data as right now
we do not inject any NUMA node information to the PV guests. When we
do get to that point, then this patch will have to be reverted."
* Disable PV NUMA support as we do not do anything with it (yet) and it
can cause bootup crashes on certain AMD machines.
* tag 'stable/for-linus-3.6-rc7-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/boot: Disable NUMA for PV guests.
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client
Pull two ceph fixes from Sage Weil:
"The first fixes a leak in the rbd setup error path, and the second
fixes a more serious problem with mismatched kmap/kunmap that surfaced
after the recent refactoring work."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
libceph: only kunmap kmapped pages
rbd: drop dev reference on error in rbd_open()
Marek Vasut [Sun, 23 Sep 2012 16:58:51 +0000 (16:58 +0000)]
phy/micrel: Add missing header to micrel_phy.h
The license header was missing in micrel_phy.h . This patch adds
one.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: David J. Choi <david.choi@micrel.com> Cc: David S. Miller <davem@davemloft.net> Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Marek Vasut [Sun, 23 Sep 2012 16:58:50 +0000 (16:58 +0000)]
phy/micrel: Rename KS80xx to KSZ80xx
There is no such part as KS8001, KS8041 or KS8051. There are only
KSZ8001, KSZ8041 and KSZ8051. Rename these parts as such to match
the Micrel naming.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: David J. Choi <david.choi@micrel.com> Cc: David S. Miller <davem@davemloft.net> Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Cc: Linux ARM kernel <linux-arm-kernel@lists.infradead.org> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Shawn Guo <shawn.guo@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Marek Vasut [Sun, 23 Sep 2012 16:58:49 +0000 (16:58 +0000)]
phy/micrel: Implement support for KSZ8021
The KSZ8021 PHY was previously caught by KS8051, which is not correct.
This PHY needs additional setup if it is strapped for address 0. In such
case an reserved bit must be written in the 0x16, "Operation Mode Strap
Override" register. According to the KS8051 datasheet, that bit means
"PHY Address 0 in non-broadcast" and it indeed behaves as such on KSZ8021.
The issue where the ethernet controller (Freescale FEC) did not communicate
with network is fixed by writing this bit as 1.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: David J. Choi <david.choi@micrel.com> Cc: David S. Miller <davem@davemloft.net> Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Chris Metcalf [Mon, 24 Sep 2012 18:57:58 +0000 (14:57 -0400)]
tile: gxio iorpc numbering change for TRIO interface
An ABI numbering change was made in the hypervisor for Tilera's 4.1
MDE release (just shipped). It's incompatible with the previous 4.0
release ABI numbering, so we track the new numbering going forward.
We plan to avoid modifying ABI numbering for these interfaces again.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
The hypervisor is in charge of allocating the proper "NUMA" memory
and dealing with the CPU scheduler to keep them bound to the proper
NUMA node. The PV guests (and PVHVM) have no inkling of where they
run and do not need to know that right now. In the future we will
need to inject NUMA configuration data (if a guest spans two or more
NUMA nodes) so that the kernel can make the right choices. But those
patches are not yet present.
In the meantime, disable the NUMA capability in the PV guest, which
also fixes a bootup issue. Andre says:
"we see Dom0 crashes due to the kernel detecting the NUMA topology not
by ACPI, but directly from the northbridge (CONFIG_AMD_NUMA).
This will detect the actual NUMA config of the physical machine, but
will crash about the mismatch with Dom0's virtual memory. Variation of
the theme: Dom0 sees what it's not supposed to see.
This happens with the said config option enabled and on a machine where
this scanning is still enabled (K8 and Fam10h, not Bulldozer class)
so we just disable NUMA scanning by setting numa_off=1.
CC: stable@vger.kernel.org Reported-and-Tested-by: Andre Przywara <andre.przywara@amd.com> Acked-by: Andre Przywara <andre.przywara@amd.com> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Merge branch 'rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild
Pull kbuild fixes from Michal Marek:
"There are two more kbuild fixes for 3.6.
One fixes a race between x86's archscripts target and the rule
(re)building scripts/basic/fixdep. The second is a fix for the
previous attempt at fixing make firmware_install with make 3.82.
This new solution should work with any version of GNU make"
* 'rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
x86/kbuild: archscripts depends on scripts_basic
firmware: fix directory creation rule matching with make 3.80
Merge branch 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging
Pull hwmon subsystem fixes from Jean Delvare.
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
hwmon: (fam15h_power) Tweak runavg_range on resume
hwmon: (coretemp) Use get_online_cpus to avoid races involving CPU hotplug
hwmon: (via-cputemp) Use get_online_cpus to avoid races involving CPU hotplug
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a set of four essential fixes: two oops related (bnx2i,
virtio-scsi), one data corruption related (hpsa) and one failure to
boot due to interrupt routing issues (mpt2ss).
Signed-off-by: James Bottomley <JBottomley@Parallels.com>"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
[SCSI] hpsa: fix handling of protocol error
[SCSI] mpt2sas: Fix for issue - Unable to boot from the drive connected to HBA
[SCSI] bnx2i: Fixed NULL ptr deference for 1G bnx2 Linux iSCSI offload
[SCSI] scsi: virtio-scsi: Fix address translation failure of HighMem pages used by sg list
edac_mc: edac_mc_free() cannot assume mem_ctl_info is registered in sysfs.
Fix potential NULL pointer dereference in edac_unregister_sysfs() on
system boot introduced in 3.6-rc1.
Since commit 7a623c039 ("edac: rewrite the sysfs code to use struct
device") edac_mc_alloc() no longer initializes embedded kobjects in
struct mem_ctl_info. Therefore edac_mc_free() can no longer simply
decrement a kobject reference count to free the allocated memory unless
the memory controller driver module had also called edac_mc_add_mc().
Now edac_mc_free() will check if the newly embedded struct device has
been registered with sysfs before using either the standard device
release functions or freeing the data structures itself with logic
pulled out of the error path of edac_mc_alloc().
The BUG this patch resolves for me:
BUG: unable to handle kernel NULL pointer dereference at (null)
EIP is at __wake_up_common+0x1a/0x6a
Process modprobe (pid: 933, ti=f3dc6000 task=f3db9520 task.ti=f3dc6000)
Call Trace:
complete_all+0x3f/0x50
device_pm_remove+0x23/0xa2
device_del+0x34/0x142
edac_unregister_sysfs+0x3b/0x5c [edac_core]
edac_mc_free+0x29/0x2f [edac_core]
e7xxx_probe1+0x268/0x311 [e7xxx_edac]
e7xxx_init_one+0x56/0x61 [e7xxx_edac]
local_pci_probe+0x13/0x15
...
and that code block seem to mess things up in several ways (double free, memory
leak, out-of-bound reads etc.):
L422: The iterator "chn" and bound "tot_channels" are totally wrong. Should be
"row" and "tot_csrows" respectively. Which means either memory leak, or
out-of-bound reads (which if does not trigger an immediate page fault
error, will further lead to kfree() on random addresses).
L425: The inner loop is reusing the same iterator "chn" as the outer loop,
which could lead to premature end of the outer loop, and hence memory leak.
L429: The array index 'i' in mci->csrows[i] is a temporary value used in
previous loops, and won't change at all in the current loop. Which
means either out-of-bound read and possibly kfree(random number), or the
same mci->csrows[i] get freed once and again, and possibly double free
for the kfree(csr) in L427.
L426/L427: a kfree(csr->channels) is needed in between to avoid leaking the memory.
The buggy code was introduced by commit de3910eb ("edac: change the mem
allocation scheme to make Documentation/kobject.txt happy") in the 3.6-rc1
merge window. Fix it by freeing up resources in this order:
batman-adv: Fix symmetry check / route flapping in multi interface setups
If receiving an OGM from a neighbor other than the currently selected
and if it has the same TQ then we are supposed to switch if this
neighbor provides a more symmetric link than the currently selected one.
However this symmetry check currently is broken if the interface of the
neighbor we received the OGM from and the one of the currently selected
neighbor differ: We are currently trying to determine the symmetry of the
link towards the selected router via the link we received the OGM from
instead of just checking via the link towards the currently selected
router.
This leads to way more route switches than necessary and can lead to
permanent route flapping in many common multi interface setups.
This patch fixes this issue by using the right interface for this
symmetry check.
Into function interface_set_mac_addr, the function tt_local_add was
invoked before updating dev->dev_addr. The new MAC address was not
tagged as NoPurge.
Andreas Herrmann [Sun, 23 Sep 2012 18:27:32 +0000 (20:27 +0200)]
hwmon: (fam15h_power) Tweak runavg_range on resume
The quirk introduced with commit 00250ec90963b7ef6678438888f3244985ecde14 (hwmon: fam15h_power: fix
bogus values with current BIOSes) is not only required during driver
load but also when system resumes from suspend. The BIOS might set the
previously recommended (but unsuitable) initilization value for the
running average range register during resume.
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com> Tested-by: Andreas Hartmann <andihartmann@01019freenet.de> Signed-off-by: Jean Delvare <khali@linux-fr.org> Cc: stable@vger.kernel.org # 3.0+
hwmon: (coretemp) Use get_online_cpus to avoid races involving CPU hotplug
coretemp_init loops with for_each_online_cpu, adding platform_devices
and sysfs interfaces, then calls register_hotcpu_notifier. There is a
race if a CPU is offlined or onlined after the loop, but before
register_hotcpu_notifier. The race might result in the absence of a
platform_device+sysfs interface for an online CPU, or the presence of
a platform_device+sysfs interface for an offline CPU. A similar race
occurs during coretemp_exit, after the module calls
unregister_hotcpu_notifier, but before it unregisters all devices, a
CPU might offline and a device for an offline CPU will exist for a
short while.
This fix surrounds for_each_online_cpu and register_hotcpu_notifier
with get_online_cpus+put_online_cpus; and surrounds
unregister_hotcpu_notifier and device unregistering with
get_online_cpus+put_online_cpus.
Build tested.
Signed-off-by: Silas Boyd-Wickizer <sbw@mit.edu> Signed-off-by: Jean Delvare <khali@linux-fr.org>
hwmon: (via-cputemp) Use get_online_cpus to avoid races involving CPU hotplug
via_cputemp_init loops with for_each_online_cpu, adding
platform_devices, then calls register_hotcpu_notifier. If a CPU is
offlined between the loop and register_hotcpu_notifier, then later
onlined, via_cputemp_device_add will attempt to add platform devices
with the same ID. A similar race occurs during via_cputemp_exit,
after the module calls unregister_hotcpu_notifier, a CPU might offline
and a device will exist for a CPU that is offline.
This fix surrounds for_each_online_cpu and register_hotcpu_notifier
with get_online_cpus+put_online_cpus; and surrounds
unregister_hotcpu_notifier and device unregistering with
get_online_cpus+put_online_cpus.
Build tested.
Signed-off-by: Silas Boyd-Wickizer <sbw@mit.edu> Acked-by: Harald Welte <laforge@gnumonks.org> Signed-off-by: Jean Delvare <khali@linux-fr.org>
When PPPOE is running over a virtual ethernet interface (e.g., a
bonding interface) and the user tries to delete the interface in case
the PPPOE state is ZOMBIE, the kernel will loop forever while
unregistering net_device for the reference count is not decreased to
zero which should have been done with dev_put().
Signed-off-by: Xiaodong Xu <stid.smth@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Pull MIPS fixes from Ralf Baechle:
"Random fixes across arch/mips, essentially.
One fix for an issue in get_user_pages_fast() which previously was
discovered on x86, a miscalculation in the support for the MIPS MT
hardware multithreading support, the RTC support for the Malta and a
fix for a spurious interrupt issue that seems to bite only very
special Malta configurations."
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: Malta: Don't crash on spurious interrupt.
MIPS: Malta: Remove RTC Data Mode bootstrap breakage
MIPS: mm: Add compound tail page _mapcount when mapped
MIPS: CMP/SMTC: Fix tc_id calculation
On some hw, link is not up during adding iface to team. That causes event
not being sent to userspace and that may cause confusion.
Fix this bug by sending port changed event once it's added to team.
Signed-off-by: Jiri Pirko <jiri@resnulli.us> Signed-off-by: David S. Miller <davem@davemloft.net>
Merge branch 'fixes' of git://git.linaro.org/people/rmk/linux-arm
Pull ARM and clkdev fixes from Russell King:
"Two patches for clkdev which resolve the long standing issue that the
devm_* versions were dependent on clkdev, which they shouldn't have
been. Instead, they're dependent on HAVE_CLK instead, which implies
that you're providing clk_get() and clk_put().
A small fix to the ARM decompressor to ensure that the page tables are
properly interpreted by the CPU, and reserve syscall 378 for kcmp (the
checksyscalls.sh script is unfortunately currently broken so arch
maintainers aren't getting notified of new syscalls...)
Lastly, a larger fix for an issue between the common clk subsystem and
smp_twd which causes warnings to be spat out."
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: reserve syscall 378 for kcmp
ARM: 7535/1: Reprogram smp_twd based on new common clk framework notifiers
ARM: 7537/1: clk: Fix release in devm_clk_put()
ARM: 7532/1: decompressor: reset SCTLR.TRE for VMSA ARMv7 cores
ARM: 7534/1: clk: Make the managed clk functions generically available
Merge branch 'upstream-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
Pull HID fixes from Jiri Kosina:
"The most important fix is Logitech Unifying receiver regression in
device enumeration fix from Nestor Lopez Casado. In addition to that,
there is a small memory leak fix for Thinkpad keyboard driver from
Axel Lin."
* 'upstream-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: Fix logitech-dj: missing Unifying device issue
HID: lenovo-tpkbd: Fix memory leak in tpkbd_remove_tp()
Since the first lines of the source code clearly state:
* This file is subject to the terms and conditions of the GNU General
* Public License. See the file "COPYING" in the main directory of this
* archive for more details.
I think it's safe to add the MODULE_LICENSE("GPL") macro and thus remove
the kernel taint.
Cc: stable@vger.kernel.org Signed-off-by: Peter Huewe <peterhuewe@gmx.de> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes an issue introduced after commit 4ea5454203d991ec
("HID: Fix race condition between driver core and ll-driver").
After that commit, hid-core discards any incoming packet that arrives while
hid driver's probe function is being executed.
This broke the enumeration process of hid-logitech-dj, that must receive
control packets in-band with the mouse and keyboard packets. Discarding mouse
or keyboard data at the very begining is usually fine, but it is not the case
for control packets.
This patch forces a re-enumeration of the paired devices when a packet arrives
that comes from an unknown device.
Based on a patch originally written by Benjamin Tissoires.
Alex Elder [Fri, 21 Sep 2012 22:59:58 +0000 (17:59 -0500)]
libceph: only kunmap kmapped pages
In write_partial_msg_pages(), pages need to be kmapped in order to
perform a CRC-32c calculation on them. As an artifact of the way
this code used to be structured, the kunmap() call was separated
from the kmap() call and both were done conditionally. But the
conditions under which the kmap() and kunmap() calls were made
differed, so there was a chance a kunmap() call would be done on a
page that had not been mapped.
The symptom of this was tripping a BUG() in kunmap_high() when
pkmap_count[nr] became 0.
Reported-by: Bryan K. Wright <bryan@virginia.edu> Signed-off-by: Alex Elder <elder@inktank.com> Reviewed-by: Sage Weil <sage@inktank.com>
Pull networking updates from David Miller:
"More bug fixes, nothing gets past these guys"
1) More kernel info leaks found by Mathias Krause, this time in the
IPSEC configuration layers.
2) When IPSEC policies change, we do not properly make sure that cached
routes (which could now be stale) throughout the system will be
revalidated. Fix this by generalizing the generation count
invalidation scheme used by ipv4. From Nicolas Dichtel.
3) When repairing TCP sockets, we need to allow to restore not just the
send window scale, but the receive one too. Extend the existing
interface to achieve this in a backwards compatible way. From
Andrey Vagin.
4) A fix for FCOE scatter gather feature validation erroneously caused
scatter gather to be disabled for things like AOE too. From Ed L
Cashin.
5) Several cases of mishandling of error pointers, from Mathias Krause,
Wei Yongjun, and Devendra Naga.
6) Fix gianfar build, from Richard Cochran.
7) CAP_NET_* failures should return -EPERM not -EACCES, from Zhao
Hongjiang.
8) Hardware reset fix in janz-ican3 CAN driver, from Ira W Snyder.
9) Fix oops during rmmod in ti_hecc CAN driver, from Marc Kleine-Budde.
10) The removal of the conditional compilation of the clk support code
in the stmmac driver broke things. This is because the interfaces
used are the ones that don't also perform the enable/disable of the
clk. Fix from Stefan Roese.
11) The QFQ packet scheduler can record out of range virtual start
times, resulting later in misbehavior and even crashes. Fix from
Paolo Valente.
12) If MSG_WAITALL is used with IOAT DMA under TCP, we can wedge the
receiver when the advertised receive window goes to zero. Detect
this case and force the processing of the IOAT DMA queue when it
happens to avoid getting stuck. Fix from Michal Kubecek.
13) batman-adv assumes that test_bit() returns only 0 or 1, but this is
not true for x86 (which returns -1 or 0, via the 'sbb' instruction).
Fix from Linus Lussing.
14) Fix small packet corruption in e1000, from Tushar Dave.
15) make_blackhole() in the IPSEC policy code can do one read unlock too
many, fix from Li RongQing.
16) The new tcp_try_coalesce() code introduced a bug in TCP URG
handling, fix from Eric Dumazet.
17) Fix memory leak in __netif_receive_skb() when doing zerocopy and
when hit an OOM condition. From Michael S Tsirkin.
18) netxen blindly deferences pdev->bus->self, which is not guarenteed
to be non-NULL. Fix from Nikolay Aleksandrov.
19) Fix a performance regression caused by mistakes in ipv6 checksum
validation in the bnx2x driver, fix from Michal Schmidt.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (45 commits)
net/stmmac: Use clk_prepare_enable and clk_disable_unprepare
net: change return values from -EACCES to -EPERM
net/irda: sh_sir: fix return value check in sh_sir_set_baudrate()
stmmac: fix return value check in stmmac_open_ext_timer()
gianfar: fix phc index build failure
ipv6: fix return value check in fib6_add()
bnx2x: remove false warning regarding interrupt number
can: ti_hecc: fix oops during rmmod
can: janz-ican3: fix support for older hardware revisions
net: do not disable sg for packets requiring no checksum
aoe: assert AoE packets marked as requiring no checksum
at91ether: return PTR_ERR if call to clk_get fails
xfrm_user: don't copy esn replay window twice for new states
xfrm_user: ensure user supplied esn replay window is valid
xfrm_user: fix info leak in copy_to_user_tmpl()
xfrm_user: fix info leak in copy_to_user_policy()
xfrm_user: fix info leak in copy_to_user_state()
xfrm_user: fix info leak in copy_to_user_auth()
net: qmi_wwan: adding Huawei E367, ZTE MF683 and Pantech P4200
tcp: restore rcv_wscale in a repair mode (v2)
...
1) Debugging builds on 32-bit sparc need to handle the R_SPARC_DISP32
relocation, not just 64-bit sparc. From Andreas Larsson.
2) Wei Yongjun noticed that module_alloc() on sparc can return an
error pointer, but that's not allowed. module_alloc() should
return only a valid pointer, or NULL.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc: fix the return value of module_alloc()
sparc32: Enable the relocation target R_SPARC_DISP32 for sparc32
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"Small fixlets"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mm/init.c: Fix devmem_is_allowed() off by one
x86/kconfig: Remove outdated reference to Intel CPUs in CONFIG_SWIOTLB
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Fixes for big 3 drivers:
nouveau: revert earlier MBP fix, put a dmi based MBP fix in its place
(fixes a regression we found on some Dell eDP panels doing some
internal testing)
radeon: revert pll fixes, real fix is too invasive, fix scratch leak
intel: 3 minor fixes, one for HDMI audio."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/nouveau: add dmi quirk for gpio reset
drm/radeon: Prevent leak of scratch register on resume from suspend
Revert "drm/nv50-/gpio: initialise to vbios defaults during init"
Revert "drm/radeon: rework pll selection (v3)"
drm/i915: HDMI - Clear Audio Enable bit for Hot Plug
drm/i915: Reduce a pin-leak BUG into a WARN
drm/i915: enable lvds pin pairs before dpll on gen2
projects / linux-beck.git / log