Simon Horman [Fri, 13 Nov 2015 02:23:51 +0000 (11:23 +0900)]
ARM: shmobile: r8a7794: Use SoC specific binding for rcar-dmac nodes
Use the new SoC specific binding for rcar-dmac and the generic
binding as a fall-back in the r8a7794 device tree.
In general Renesas hardware is not documented to the extent where the
relationship between IP blocks on different SoCs can be assumed although
they may appear to operate the same way. Furthermore the documentation
typically does not specify a version for individual IP blocks. For these
reasons a convention of using the SoC name in place of a version and
providing SoC-specific compat strings has been adopted.
Although not universally liked this convention is used in the bindings for
most drivers for Renesas hardware. The purpose of this patch is to
update the Renesas R-Car DMA Controller nodes to follow this convention.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Simon Horman [Fri, 13 Nov 2015 02:23:50 +0000 (11:23 +0900)]
ARM: shmobile: r8a7793: Use SoC specific binding for rcar-dmac nodes
Use the new SoC specific binding for rcar-dmac and the generic
binding as a fall-back in the r8a7793 device tree.
In general Renesas hardware is not documented to the extent where the
relationship between IP blocks on different SoCs can be assumed although
they may appear to operate the same way. Furthermore the documentation
typically does not specify a version for individual IP blocks. For these
reasons a convention of using the SoC name in place of a version and
providing SoC-specific compat strings has been adopted.
Although not universally liked this convention is used in the bindings for
most drivers for Renesas hardware. The purpose of this patch is to
update the Renesas R-Car DMA Controller nodes to follow this convention.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Simon Horman [Fri, 13 Nov 2015 02:23:49 +0000 (11:23 +0900)]
ARM: shmobile: r8a7791: Use SoC specific binding for rcar-dmac nodes
Use the new SoC specific binding for rcar-dmac and the generic
binding as a fall-back in the r8a7791 device tree.
In general Renesas hardware is not documented to the extent where the
relationship between IP blocks on different SoCs can be assumed although
they may appear to operate the same way. Furthermore the documentation
typically does not specify a version for individual IP blocks. For these
reasons a convention of using the SoC name in place of a version and
providing SoC-specific compat strings has been adopted.
Although not universally liked this convention is used in the bindings for
most drivers for Renesas hardware. The purpose of this patch is to
update the Renesas R-Car DMA Controller nodes to follow this convention.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Simon Horman [Fri, 13 Nov 2015 02:23:48 +0000 (11:23 +0900)]
ARM: shmobile: r8a7790: Use SoC specific binding for rcar-dmac nodes
Use the new SoC specific binding for rcar-dmac and the generic
binding as a fall-back in the r8a7790 device tree.
In general Renesas hardware is not documented to the extent where the
relationship between IP blocks on different SoCs can be assumed although
they may appear to operate the same way. Furthermore the documentation
typically does not specify a version for individual IP blocks. For these
reasons a convention of using the SoC name in place of a version and
providing SoC-specific compat strings has been adopted.
Although not universally liked this convention is used in the bindings for
most drivers for Renesas hardware. The purpose of this patch is to
update the Renesas R-Car DMA Controller nodes to follow this convention.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Magnus Damm [Mon, 16 Nov 2015 08:57:29 +0000 (17:57 +0900)]
ARM: shmobile: r8a7794: alt: Enable VGA port
Enable the DU device and the VGA port available on the r8a7794
ALT board. The VGA portion of the ALT board is somewhat similar
to the Lager board but in case of ALT the DU1 pins are used
and the X2 clock has a reduced frequency.
This patch does not include any pinctrl (PFC) settings due to lack
of PFC DT integration on r8a7794. At this point the default state
of the boot loader is enough to keep the VGA port working without
changing any pinctrl settings.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
ARM: shmobile: koelsch: Move SPI FLASH partitions to subnode
As of commits 5cfdedb7b9a0fe38 ("mtd: ofpart: move ofpart partitions to a
dedicated dt node") and fe2585e9c29a650a ("doc: dt: mtd: support
partitions in a special 'partitions' subnode"), having partitions as
direct subnodes of an mtd device is discouraged:
spi0.0: 'partitions' subnode not found on /spi@e6b10000/flash@0. Trying to parse direct subnodes as partitions.
Hence move the SPI FLASH partitions to a "partitions" subnode.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Sergei Shtylyov [Wed, 28 Oct 2015 21:34:29 +0000 (00:34 +0300)]
ARM: shmobile: henninger: remove board DT
The Henninger low cost board was never sold and so had no users outside
Renesas (and Cogent Embedded). Instead Renesas has made the Porter board
which has mostly similar hardware. Now that the Porter board support is on
par with Henninger, we can remove the Henninger's device tree file.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Sergei Shtylyov [Tue, 27 Oct 2015 21:03:22 +0000 (00:03 +0300)]
ARM: shmobile: porter: add CAN0 DT support
Define the Porter board dependent part of the CAN0 device node.
This patch is analogous to the commit 457acc4a6ce8 ("ARM: shmobile:
henninger: add CAN0 DT support") as there are no differences between the
boards in this respect.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Magnus Damm [Sun, 18 Oct 2015 05:26:56 +0000 (14:26 +0900)]
ARM: shmobile: r8a7794: Disable all IPMMU nodes by default
The r8a7794 IPMMU nodes for MX and DS are currently lacking
a line containing 'status = "disabled"', fix this by
making sure they are disabled like all other IPMMU nodes.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Sudeep Holla [Wed, 21 Oct 2015 10:10:11 +0000 (11:10 +0100)]
ARM: dts: shmobile/r8a7xxx: replace gpio-key, wakeup with wakeup-source property
Though the keyboard driver for GPIO buttons(gpio-keys) will continue to
check for/support the legacy "gpio-key,wakeup" boolean property to
enable gpio buttons as wakeup source, "wakeup-source" is the new
standard binding.
This patch replaces the legacy "gpio-key,wakeup" with the unified
"wakeup-source" property in order to avoid any futher copy-paste
duplication.
Sergei Shtylyov [Wed, 14 Oct 2015 19:35:46 +0000 (22:35 +0300)]
ARM: shmobile: porter: add HS-USB DT support
Enable HS-USB device for the Porter board, defining the GPIO that the
driver should check when probing (which is the ID output from MAX3355
OTG chip).
Note that there will be pinctrl-related error messages if both internal
PCI and HS-USB drivers are enabled but they should be just ignored.
This patch is analogous to the commit 6f4f7156e0e6 ("ARM: shmobile:
henninger: enable HS-USB") as there are no differences between the
boards in this respect.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Sergei Shtylyov [Mon, 12 Oct 2015 22:12:18 +0000 (01:12 +0300)]
ARM: shmobile: porter: enable internal PCI and USB PHY
Enable internal AHB-PCI bridges for the USB EHCI/OHCI controllers attached
to them and also enable USB PHY device for the Porter board. We have to
enable everything in one patch since EHCI/OHCI devices are already linked
to the USB PHY device.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Sergei Shtylyov [Fri, 9 Oct 2015 21:41:26 +0000 (00:41 +0300)]
ARM: shmobile: porter: enable PCIe
Enable the PCIe controller and clock for the Porter board.
This patch is analogous to the commit 485f3ce67c11 ("ARM: shmobile:
henninger: Enable PCIe Controller & PCIe bus clock") as there are no
differences between the boards in this respect.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Sergei Shtylyov [Fri, 9 Oct 2015 21:40:31 +0000 (00:40 +0300)]
ARM: shmobile: porter: add QSPI DT support
Define the Porter board dependent part of the QSPI device node.
Add device nodes for Spansion S25FL512S SPI flash and the MTD partitions
on it.
This patch is mostly analogous to the commit f59838d44835 ("ARM:
shmobile: henninger: add QSPI DT support") as there are no differences
between the boards in this respect.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Sergei Shtylyov [Thu, 8 Oct 2015 21:45:49 +0000 (00:45 +0300)]
ARM: shmobile: porter: add VIN0/ADV7180 DT support
Define the Porter board dependent part of the VIN0 device node.
Add the device node for Analog Devices ADV7180 video decoder to I2C2 bus.
Add the necessary subnodes to interconnect VIN0 and ADV7180 devices.
This patch is analogous to the commit 8d62f4f75320 ("ARM: shmobile:
henninger: add VIN0/ADV7180 DT support") as there are no differences
between the boards in this respect.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Sergei Shtylyov [Thu, 8 Oct 2015 21:44:18 +0000 (00:44 +0300)]
ARM: shmobile: porter: add I2C2 DT support
Define the Porter board dependent part of the I2C2 device node.
This patch is analogous to the commit 29a647c396a0 ("ARM: shmobile:
henninger: add I2C2 DT support") as there are no differences between
the boards in this respect.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Sergei Shtylyov [Wed, 7 Oct 2015 22:00:06 +0000 (01:00 +0300)]
ARM: shmobile: porter: enable SATA0
Enable SATA0 device for the Porter board.
This patch is analogous to the commit 5a62ec57004f ("ARM: shmobile:
henninger: enable SATA0") as there are no differences between the boards
in this respect.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Sergei Shtylyov [Tue, 6 Oct 2015 23:05:41 +0000 (02:05 +0300)]
ARM: shmobile: porter: add SDHI0/2 DT support
Define the Porter board dependent part of the SDHI0/2 device nodes along
with the necessary voltage regulators (note that the Vcc regulators are
dummy -- they are required but don't actually exist on the board). Also,
GPIOs have to be used for the CD and WP signals due to the SDHI driver
constraints...
This patch is analogous to the commit 1299df03d719 ("ARM: shmobile:
henninger: add SDHI0/2 DT support") as there are no differences between
those boards in this respect.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Sergei Shtylyov [Mon, 5 Oct 2015 22:51:01 +0000 (01:51 +0300)]
ARM: shmobile: porter: add Ether DT support
Define the Porter board dependent part of the Ether device node.
Enable DHCP and NFS root for the kernel booting.
This patch is analogous to the commit 26b0d2cf73cb ("ARM: shmobile:
henninger: add Ether DT support") as there are no differences between
those boards in this respect.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Sergei Shtylyov [Fri, 2 Oct 2015 21:53:38 +0000 (00:53 +0300)]
ARM: shmobile: fix SILK board name
Unfortunately, the SILK board bindings were not quite correct, as the board
name should be all caps. Fix that, adding the board model # in parens and
removing stray semicolon.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
ARM: shmobile: dts: Add common file for AA121TD01 panel
The Mitsubishi AA121TD01 panel is commonly used with the Marzen, Lager
and Koelsch boards. Create a .dtsi file that describe the panel and its
connection to the board.
Wolfram Sang [Wed, 9 Sep 2015 17:48:19 +0000 (19:48 +0200)]
ARM: shmobile: r8a7790: lager: add pinmux for iic0
It seems we used to rely on the default pinmux setting of this HW, but
currently we need to explicitly set the pinmux to access this bus. It is
better style, too.
Signed-off-by: Wolfram Sang <wsa@sang-engineering.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Sergei Shtylyov [Wed, 19 Aug 2015 22:24:47 +0000 (01:24 +0300)]
ARM: shmobile: silk: add VIN0/ADV7180 DT support
Define the SILK board dependent part of the VIN0 device node.
Add the device node for Analog Devices ADV7180 video decoder to I2C1 bus.
Add the necessary subnodes to interconnect VIN0 and ADV7180 devices.
Based on the Henninger VIN0/ADV8170 device tree patch by myself.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Simon Horman [Thu, 20 Aug 2015 23:27:44 +0000 (16:27 -0700)]
ARM: shmobile: remove Makefile.boot
Now that the only multiplatform boot is supported for all
shmobile platforms Makefile.boot may be removed.
This seems correct to me given:
* Setting MACHINE to no value in arch/arm/Makefile
if CONFIG_ARCH_MULTIPLATFORM is set
* Not including Makefile.boot in arch/arm/boot/Makefile
if MACHINE has no value
Signed-off-by: Simon Horman <horms+renesas@verge.net.au> Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Merge tag 'cris-for-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/jesper/cris
Pull CRIS updates from Jesper Nilsson:
"Mostly removal of old cruft of which we can use a generic version, or
fixes for code not commonly run in the cris port, but also additions
to enable some good debug"
* tag 'cris-for-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/jesper/cris: (25 commits)
CRISv10: delete unused lib/dmacopy.c
CRISv10: delete unused lib/old_checksum.c
CRIS: fix switch_mm() lockdep splat
CRISv32: enable LOCKDEP_SUPPORT
CRIS: add STACKTRACE_SUPPORT
CRISv32: annotate irq enable in idle loop
CRISv32: add support for irqflags tracing
CRIS: UAPI: use generic types.h
CRIS: UAPI: use generic shmbuf.h
CRIS: UAPI: use generic msgbuf.h
CRIS: UAPI: use generic socket.h
CRIS: UAPI: use generic sembuf.h
CRIS: UAPI: use generic sockios.h
CRIS: UAPI: use generic auxvec.h
CRIS: UAPI: use generic headers via Kbuild
CRIS: UAPI: fix elf.h export
CRIS: don't make asm/elf.h depend on asm/user.h
CRIS: UAPI: fix ptrace.h
CRISv32: Squash compile warnings for axisflashmap
CRISv32: Add GPIO driver to the default configs
...
Linus Torvalds [Wed, 27 May 2015 22:32:15 +0000 (15:32 -0700)]
blk: rq_data_dir() should not return a boolean
rq_data_dir() returns either READ or WRITE (0 == READ, 1 == WRITE), not
a boolean value.
Now, admittedly the "!= 0" doesn't really change the value (0 stays as
zero, 1 stays as one), but it's not only redundant, it confuses gcc, and
causes gcc to warn about the construct
switch (rq_data_dir(req)) {
case READ:
...
case WRITE:
...
that we have in a few drivers.
Now, the gcc warning is silly and stupid (it seems to warn not about the
switch value having a different type from the case statements, but about
_any_ boolean switch value), but in this case the code itself is silly
and stupid too, so let's just change it, and get rid of warnings like
this:
drivers/block/hd.c: In function ‘hd_request’:
drivers/block/hd.c:630:11: warning: switch condition has boolean value [-Wswitch-bool]
switch (rq_data_dir(req)) {
The odd '!= 0' came in when "cmd_flags" got turned into a "u64" in
commit 5953316dbf90 ("block: make rq->cmd_flags be 64-bit") and is
presumably because the old code (that just did a logical 'and' with 1)
would then end up making the type of rq_data_dir() be u64 too.
But if we want to retain the old regular integer type, let's just cast
the result to 'int' rather than use that rather odd '!= 0'.
Fix up the writeback plugging introduced in commit d353d7587d02
("writeback: plug writeback at a high level") that then caused problems
due to the unplug happening with a spinlock held.
* writeback-plugging:
writeback: plug writeback in wb_writeback() and writeback_inodes_wb()
Revert "writeback: plug writeback at a high level"
writeback: plug writeback in wb_writeback() and writeback_inodes_wb()
We had to revert the pluggin in writeback_sb_inodes() because the
wb->list_lock is held, but we could easily plug at a higher level before
taking that lock, and unplug after releasing it. This does that.
Chris will run performance numbers, just to verify that this approach is
comparable to the alternative (we could just drop and re-take the lock
around the blk_finish_plug() rather than these two commits.
I'd have preferred waiting for actual performance numbers before picking
one approach over the other, but I don't want to release rc1 with the
known "sleeping function called from invalid context" issue, so I'll
pick this cleanup version for now. But if the numbers show that we
really want to plug just at the writeback_sb_inodes() level, and we
should just play ugly games with the spinlock, we'll switch to that.
Cc: Chris Mason <clm@fb.com> Cc: Josef Bacik <jbacik@fb.com> Cc: Dave Chinner <david@fromorbit.com> Cc: Neil Brown <neilb@suse.de> Cc: Jan Kara <jack@suse.cz> Cc: Christoph Hellwig <hch@lst.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I didn't notice this when merging the thermal code from Zhang, but his
merge (commit 5a924a07f882: "Merge branches 'thermal-core' and
'thermal-intel' of .git into next") of the thermal-core and
thermal-intel branches was wrong.
In thermal-core, commit 17e8351a7739 ("thermal: consistently use int for
temperatures") converted the thermal layer to use "int" for
temperatures.
But in parallel, in the thermal-intel branch commit d0a12625d2ff
("thermal: Add Intel PCH thermal driver") added support for the intel
PCH thermal sensor using the old interfaces that used "unsigned long"
pointers.
This resulted in warnings like this:
drivers/thermal/intel_pch_thermal.c:184:14: warning: initialization from incompatible pointer type [-Wincompatible-pointer-types]
.get_temp = pch_thermal_get_temp,
^
drivers/thermal/intel_pch_thermal.c:184:14: note: (near initialization for ‘tzd_ops.get_temp’)
drivers/thermal/intel_pch_thermal.c:186:19: warning: initialization from incompatible pointer type [-Wincompatible-pointer-types]
.get_trip_temp = pch_get_trip_temp,
^
drivers/thermal/intel_pch_thermal.c:186:19: note: (near initialization for ‘tzd_ops.get_trip_temp’)
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
revert "ocfs2/dlm: use list_for_each_entry instead of list_for_each"
mm/early_ioremap: add explicit #include of asm/early_ioremap.h
fs/seq_file: convert int seq_vprint/seq_printf/etc... returns to void
selftests: enhance membarrier syscall test
selftests: add membarrier syscall test
sys_membarrier(): system-wide memory barrier (generic, x86)
MODSIGN: fix a compilation warning in extract-cert
Merge tag 'ntb-4.3' of git://github.com/jonmason/ntb
Pull NTB fixes from Jon Mason:
"NTB bug and documentation fixes, new device IDs, performance
improvements, and adding a mailing list to MAINTAINERS for NTB"
* tag 'ntb-4.3' of git://github.com/jonmason/ntb:
NTB: Fix range check on memory window index
NTB: Improve index handling in B2B MW workaround
NTB: Fix documentation for ntb_peer_db_clear.
NTB: Fix documentation for ntb_link_is_up
NTB: Use unique DMA channels for TX and RX
NTB: Remove dma_sync_wait from ntb_async_rx
NTB: Clean up QP stats info
NTB: Make the transport list in order of discovery
NTB: Add PCI Device IDs for Broadwell Xeon
NTB: Add flow control to the ntb_netdev
NTB: Add list to MAINTAINERS
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull more input updates from Dmitry Torokhov:
"Second round of updates for the input subsystem.
This introduces two brand new touchscreen drivers (Colibri and
imx6ul_tsc), some small driver fixes, and we are no longer report
errors from evdev_flush() as users do not really have a way of
handling errors, error codes that we were returning were not on the
list of errors supposed to be returned by close(), and errors were
causing issues with one of older versions of systemd"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: imx_keypad - remove obsolete comment
Input: touchscreen - add imx6ul_tsc driver support
Input: Add touchscreen support for Colibri VF50
Input: i8042 - lower log level for "no controller" message
Input: evdev - do not report errors form flush()
Input: elants_i2c - extend the calibration timeout to 12 seconds
Input: sparcspkr - fix module autoload for OF platform drivers
Input: regulator-haptic - fix module autoload for OF platform driver
Input: pwm-beeper - fix module autoload for OF platform driver
Input: ab8500-ponkey - Fix module autoload for OF platform driver
Input: cyttsp - remove unnecessary MODULE_ALIAS()
Input: elan_i2c - add ACPI ID "ELAN1000"
Merge tag 'pm+acpi-4.3-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more power management and ACPI updates from Rafael Wysocki:
"These are mostly fixes and cleanups on top of the previous PM+ACPI
pull request (cpufreq core and drivers, cpuidle, generic power domains
framework). Some of them didn't make to that pull request and some
fix issues introduced by it.
The only really new thing is the support for suspend frequency in the
cpufreq-dt driver, but it is needed to fix an issue with Exynos
platforms.
Specifics:
- build fix for the new Mediatek MT8173 cpufreq driver (Guenter
Roeck).
- generic power domains framework fixes (power on error code path,
subdomain removal) and cleanup of a deprecated API user (Geert
Uytterhoeven, Jon Hunter, Ulf Hansson).
- cpufreq-dt driver fixes including two fixes for bugs related to the
new Operating Performance Points Device Tree bindings introduced
recently (Viresh Kumar).
- suspend frequency support for the cpufreq-dt driver (Bartlomiej
Zolnierkiewicz, Viresh Kumar).
- cpufreq core cleanups (Viresh Kumar).
- intel_pstate driver fixes (Chen Yu, Kristen Carlson Accardi).
- additional sanity check in the cpuidle core (Xunlei Pang).
- fix for a comment related to CPU power management (Lina Iyer)"
* tag 'pm+acpi-4.3-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
intel_pstate: fix PCT_TO_HWP macro
intel_pstate: Fix user input of min/max to legal policy region
PM / OPP: Return suspend_opp only if it is enabled
cpufreq-dt: add suspend frequency support
cpufreq: allow cpufreq_generic_suspend() to work without suspend frequency
PM / OPP: add dev_pm_opp_get_suspend_opp() helper
staging: board: Migrate away from __pm_genpd_name_add_device()
cpufreq: Use __func__ to print function's name
cpufreq: staticize cpufreq_cpu_get_raw()
PM / Domains: Ensure subdomain is not in use before removing
cpufreq: Add ARM_MT8173_CPUFREQ dependency on THERMAL
cpuidle/coupled: Add sanity check for safe_state_index
PM / Domains: Try power off masters in error path of __pm_genpd_poweron()
cpufreq: dt: Tolerance applies on both sides of target voltage
cpufreq: dt: Print error on failing to mark OPPs as shared
cpufreq: dt: Check OPP count before marking them shared
kernel/cpu_pm: fix cpu_cluster_pm_exit comment
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull second round of SCSI updates from James Bottomley:
"There's one late arriving patch here (added today), fixing a build
issue which the scsi_dh patch set in here uncovered. Other than that,
everything has been incubated in -next and the checkers for a week.
The major pieces of this patch are a set patches facilitating better
integration between scsi and scsi_dh (the device handling layer used
by multi-path; all the dm parts are acked by Mike Snitzer).
This also includes driver updates for mp3sas, scsi_debug and an
assortment of bug fixes"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (50 commits)
scsi_dh: fix randconfig build error
scsi: fix scsi_error_handler vs. scsi_host_dev_release race
fcoe: Convert use of __constant_htons to htons
mpt2sas: setpci reset kernel oops fix
pm80xx: Don't override ts->stat on IO_OPEN_CNX_ERROR_HW_RESOURCE_BUSY
lpfc: Fix possible use-after-free and double free in lpfc_mbx_cmpl_rdp_page_a2()
bfa: Fix incorrect de-reference of pointer
bfa: Fix indentation
scsi_transport_sas: Remove check for SAS expander when querying bay/enclosure IDs.
scsi_debug: resp_request: remove unused variable
scsi_debug: fix REPORT LUNS Well Known LU
scsi_debug: schedule_resp fix input variable check
scsi_debug: make dump_sector static
scsi_debug: vfree is null safe so drop the check
scsi_debug: use SCSI_W_LUN_REPORT_LUNS instead of SAM2_WLUN_REPORT_LUNS;
scsi_debug: define pr_fmt() for consistent logging
mpt2sas: Refcount fw_events and fix unsafe list usage
mpt2sas: Refcount sas_device objects and fix unsafe list usage
scsi_dh: return SCSI_DH_NOTCONN in scsi_dh_activate()
scsi_dh: don't allow to detach device handlers at runtime
...
Merge tag 'media/v4.3-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
"A series of patches that move part of the code used to allocate memory
from the media subsystem to the mm subsystem"
[ The mm parts have been acked by VM people, and the series was
apparently in -mm for a while - Linus ]
* tag 'media/v4.3-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] drm/exynos: Convert g2d_userptr_get_dma_addr() to use get_vaddr_frames()
[media] media: vb2: Remove unused functions
[media] media: vb2: Convert vb2_dc_get_userptr() to use frame vector
[media] media: vb2: Convert vb2_vmalloc_get_userptr() to use frame vector
[media] media: vb2: Convert vb2_dma_sg_get_userptr() to use frame vector
[media] vb2: Provide helpers for mapping virtual addresses
[media] media: omap_vout: Convert omap_vout_uservirt_to_phys() to use get_vaddr_pfns()
[media] mm: Provide new get_vaddr_frames() helper
[media] vb2: Push mmap_sem down to memops
Merge tag 'edac/v4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-edac
Pull edac updates from Mauro Carvalho Chehab:
"Two EDAC fixes for Intel systems (Haswell and Ivy Bridge)"
* tag 'edac/v4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-edac:
sb_edac: correctly fetch DIMM width on Ivy Bridge and Haswell
sb_edac: look harder for DDRIO on Haswell systems
Merge branch 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux
Pull thermal updates from Zhang Rui:
- use int instead of unsigned long to represent temperature to avoid
bogus overheat detection when negative temperature reported. From
Sascha Hauer.
- export available thermal governors information to user space via
sysfs. From Wei Ni.
- introduce new thermal driver for Wildcat Point platform controller
hub, which uses PCH thermal sensor and associated critical and hot
trip points. From Tushar Dave.
- add suuport for Intel Skylake and Denlow platforms in powerclamp
driver.
- some small cleanups in thermal core.
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
thermal: Add Intel PCH thermal driver
thermal: Add comment explaining test for critical temperature
thermal: Use IS_ENABLED instead of #ifdef
thermal: remove unnecessary call to thermal_zone_device_set_polling
thermal: trivial: fix typo in comment
thermal: consistently use int for temperatures
thermal: add available policies sysfs attribute
thermal/powerclamp: add cpu id for denlow platform
thermal/powerclamp: add cpu id for Skylake u/y
thermal/powerclamp: add cpu id for skylake h/s
projects / linux-beck.git / log