Merge tag 'dwc3-for-v3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
usb: dwc3: patches for v3.5 merge window
This pull request contains one workaround for a Silicon
Issue found on all RTL releases prior to 2.20a, which
would cause a metastability state on Run/Stop bit.
We also have some patches implementing a few extra Standard
requests introduced by USB3 spec (Set SEL and Set Isoch Delay),
as well as one patch, which has been pending for a long time,
implementing LPM support.
Last, but not least, we are splitting the host address space
out of the dwc3 core driver otherwise xHCI won't be able to
request_mem_region() its own address space. This patch is
only needed because we are (as we should) re-using the xHCI
driver, which is a completely separate module.
Together with these three big changes, come a few extra preparatory
patches which most move code around, define macros and so on, as
well as a fix for Isochronous transfers which hasn't been triggered
before.
[ resolved conflicts and build error in drivers/usb/dwc3/gadget.c - gregkh]
Merge tag 'gadget-for-v3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
usb: gadget: patches for v3.5
This pull request is quite big, but mainly because there's a
giant rework of the s3c_hsotg.c driver to make it friendlier
for other users. Samsung Exynos platforms use the DesignWare
Core USB2 IP from Synopsys so it's a bit unfair to have the
driver work for Samsung platforms only. In short, the big
rework is in preparation to make the driver more reusable.
Another big rework in this pull request came from Ido, where
he's removing the redundant pointer for the endpoint descriptor
from the controller driver's own endpoint representation. The
same pointer is available through the generic struct usb_ep
structure.
Also on this pull request is the conversion of a few extra
controller drivers to the new style registration, which allows
multiple controllers to be available on the same platform and
helps remove global pointers from those drivers.
Together with those big changes, there's the usual fixes and cleanups
to gadget drivers. Nothing major.
Linus Torvalds [Sun, 6 May 2012 19:19:38 +0000 (12:19 -0700)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes form Peter Anvin
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
intel_mid_powerbtn: mark irq as IRQF_NO_SUSPEND
arch/x86/platform/geode/net5501.c: change active_low to 0 for LED driver
x86, relocs: Remove an unused variable
asm-generic: Use __BITS_PER_LONG in statfs.h
x86/amd: Re-enable CPU topology extensions in case BIOS has disabled it
Linus Torvalds [Sun, 6 May 2012 17:20:07 +0000 (10:20 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"The big ones here are a memory leak we introduced in rc1, and a
scheduling while atomic if the transid on disk doesn't match the
transid we expected. This happens for corrupt blocks, or out of date
disks.
It also fixes up the ioctl definition for our ioctl to resolve logical
inode numbers. The __u32 was a merging error and doesn't match what
we ship in the progs."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: avoid sleeping in verify_parent_transid while atomic
Btrfs: fix crash in scrub repair code when device is missing
btrfs: Fix mismatching struct members in ioctl.h
Btrfs: fix page leak when allocing extent buffers
Btrfs: Add properly locking around add_root_to_dirty_list
Al Viro [Sun, 6 May 2012 16:20:00 +0000 (17:20 +0100)]
x86: fix broken TASK_SIZE for ia32_aout
Setting TIF_IA32 in load_aout_binary() used to be enough; these days
TASK_SIZE is controlled by TIF_ADDR32 and that one doesn't get set
there. Switch to use of set_personality_ia32()...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Chris Mason [Sun, 6 May 2012 11:23:47 +0000 (07:23 -0400)]
Btrfs: avoid sleeping in verify_parent_transid while atomic
verify_parent_transid needs to lock the extent range to make
sure no IO is underway, and so it can safely clear the
uptodate bits if our checks fail.
But, a few callers are using it with spinlocks held. Most
of the time, the generation numbers are going to match, and
we don't want to switch to a blocking lock just for the error
case. This adds an atomic flag to verify_parent_transid,
and changes it to return EAGAIN if it needs to block to
properly verifiy things.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Linus Torvalds [Sat, 5 May 2012 23:34:38 +0000 (16:34 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mattst88/alpha
Pull alpha fixes from Matt Turner:
"My alpha tree is back up (after taking quite some time to get my GPG
key signed). It contains just some simple fixes."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mattst88/alpha:
alpha: silence 'const' warning in sys_marvel.c
alpha: include module.h to fix modpost on Tsunami
alpha: properly define get/set_rtc_time on Marvel/SMP
alpha: VGA_HOSE depends on VGA_CONSOLE
Jiri Slaby [Sat, 5 May 2012 20:49:10 +0000 (22:49 +0200)]
TTY: pdc_cons, fix regression in close
The test in pdc_console_tty_close '!tty->count' was always wrong
because tty->count is decremented after tty->ops->close is called and
thus can never be zero. Hence the 'then' branch was never executed and
the timer never deleted.
This did not matter until commit 5dd5bc40f3b6 ("TTY: pdc_cons, use
tty_port"). There we needed to set TTY in tty_port to NULL, but this
never happened due to the bug above.
So change the test to really trigger at the last close by changing the
condition to 'tty->count == 1'.
Well, the driver should not touch tty->count at all. It should use
tty_port->count and count open count there itself.
Linus Torvalds [Sat, 5 May 2012 17:07:06 +0000 (10:07 -0700)]
Merge tag 'sound-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound sound fixes from Takashi Iwai:
"As good as nothing exciting here; just a few trivial fixes for various
ASoC stuff."
* tag 'sound-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ASoC: omap-pcm: Free dma buffers in case of error.
ASoC: s3c2412-i2s: Fix dai registration
ASoC: wm8350: Don't use locally allocated codec struct
ASoC: tlv312aic23: unbreak resume
ASoC: bf5xx-ssm2602: Set DAI format
ASoC: core: check of_property_count_strings failure
ASoC: dt: sgtl5000.txt: Add description for 'reg' field
ASoC: wm_hubs: Make sure we don't disable differential line outputs
Sasha Levin [Sat, 5 May 2012 15:06:35 +0000 (17:06 +0200)]
init: don't try mounting device as nfs root unless type fully matches
Currently, we'll try mounting any device who's major device number is
UNNAMED_MAJOR as NFS root. This would happen for non-NFS devices as
well (such as 9p devices) but it wouldn't cause any issues since
mounting the device as NFS would fail quickly and the code proceeded to
doing the proper mount:
[ 101.522716] VFS: Unable to mount root fs via NFS, trying floppy.
[ 101.534499] VFS: Mounted root (9p filesystem) on device 0:18.
Commit 6829a048102a ("NFS: Retry mounting NFSROOT") introduced retries
when mounting NFS root, which means that now we don't immediately fail
and instead it takes an additional 90+ seconds until we stop retrying,
which has revealed the issue this patch fixes.
This meant that it would take an additional 90 seconds to boot when
we're not using a device type which gets detected in order before NFS.
This patch modifies the NFS type check to require device type to be
'Root_NFS' instead of requiring the device to have an UNNAMED_MAJOR
major. This makes boot process cleaner since we now won't go through
the NFS mounting code at all when the device isn't an NFS root
("/dev/nfs").
Lin Ming [Mon, 23 Apr 2012 01:03:49 +0000 (09:03 +0800)]
ACPI: Fix D3hot v D3cold confusion
Before this patch, ACPI_STATE_D3 incorrectly referenced D3hot
in some places, but D3cold in other places.
After this patch, ACPI_STATE_D3 always means ACPI_STATE_D3_COLD;
and all references to D3hot use ACPI_STATE_D3_HOT.
ACPI's _PR3 method is used to enter both D3hot and D3cold states.
What distinguishes D3hot from D3cold is the presence _PR3
(Power Resources for D3hot) If these resources are all ON,
then the state is D3hot. If _PR3 is not present,
or all _PR0 resources for the devices are OFF,
then the state is D3cold.
This patch applies after Linux-3.4-rc1.
A future syntax cleanup may remove ACPI_STATE_D3
to emphasize that it always means ACPI_STATE_D3_COLD.
Signed-off-by: Lin Ming <ming.m.lin@intel.com> Acked-by: Rafael J. Wysocki <rjw@sisk.pl> Reviewed-by: Aaron Lu <aaron.lu@amd.com> Signed-off-by: Len Brown <len.brown@intel.com>
Commit ec81aecb2966 ("hfs: fix a potential buffer overflow") fixed a few
potential buffer overflows in the hfs filesystem. But as Timo Warns
pointed out, these changes also need to be made on the hfsplus
filesystem as well.
Reported-by: Timo Warns <warns@pre-sense.de> Acked-by: WANG Cong <amwang@redhat.com> Cc: Alexey Khoroshilov <khoroshilov@ispras.ru> Cc: Miklos Szeredi <mszeredi@suse.cz> Cc: Sage Weil <sage@newdream.net> Cc: Eugene Teo <eteo@redhat.com> Cc: Roman Zippel <zippel@linux-m68k.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Christoph Hellwig <hch@lst.de> Cc: Alexey Dobriyan <adobriyan@gmail.com> Cc: Dave Anderson <anderson@redhat.com> Cc: stable <stable@vger.kernel.org> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
'ARM: OMAP3: USB: Fix the EHCI ULPI PHY reset issue' (1fcb57d0f) created a regression
with Beagleboard xM if booting the kernel after running 'usb start' under u-boot.
Finishing the reset before calling 'usb_add_hcd' fixes the regression. This is most likely due to
usb_add_hcd calling the driver's reset and init functions which expect the hardware to be
up and running.
I previously cleaned up the err() call usage in this driver, but it
really was calling this macro instead. To remove future confusion, just
delete this unused macro now.
Ideally, the warn() and info() macros should also be removed, and the
"real" dev_warn() and dev_info() calls should be used instead.
Reported-by: Paul Gortmaker <paul.gortmaker@windriver.com> Cc: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus Torvalds [Fri, 4 May 2012 22:34:21 +0000 (15:34 -0700)]
Merge git://git.samba.org/sfrench/cifs-2.6
Pull CIFS fixes from Steve French.
* git://git.samba.org/sfrench/cifs-2.6:
fs/cifs: fix parsing of dfs referrals
cifs: make sure we ignore the credentials= and cred= options
[CIFS] Update cifs version to 1.78
cifs - check S_AUTOMOUNT in revalidate
cifs: add missing initialization of server->req_lock
cifs: don't cap ra_pages at the same level as default_backing_dev_info
CIFS: Fix indentation in cifs_show_options
Dave Jones [Fri, 4 May 2012 16:04:17 +0000 (12:04 -0400)]
CPU frequency drivers MAINTAINERS update
Remove myself as cpufreq maintainer.
x86 driver changes can go through the regular x86/ACPI trees.
ARM driver changes through the ARM trees.
cpufreq core changes are rare these days, and can just go to lkml/direct.
Signed-off-by: Dave Jones <davej@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
USB: input: usbtouchscreen.c: fix up dev_* messages
Previously I had made the struct device point to the input device, but
after talking with Dmitry, he said that the USB device would make more
sense for this driver to point to. So converted it to use that instead.
Previously I had made the struct device point to the input device, but
after talking with Dmitry, he said that the USB device would make more
sense for this driver to point to. So converted it to use that instead.
CC: Dmitry Torokhov <dmitry.torokhov@gmail.com> CC: Ping Cheng <pingc@wacom.com> CC: Chris Bagwell <chris@cnpbagwell.com> CC: Eduard Hasenleithner <eduard@hasenleithner.at> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Previously I had made the struct device point to the input device, but
after talking with Dmitry, he said that the USB device would make more
sense for this driver to point to. So converted it to use that instead.
Previously I had made the struct device point to the input device, but
after talking with Dmitry, he said that the USB device would make more
sense for this driver to point to. So converted it to use that instead.
Previously I had made the struct device point to the input device, but
after talking with Dmitry, he said that the USB device would make more
sense for this driver to point to. So converted it to use that instead.
Previously I had made the struct device point to the input device, but
after talking with Dmitry, he said that the USB device would make more
sense for this driver to point to. So converted it to use that instead.
Previously I had made the struct device point to the input device, but
after talking with Dmitry, he said that the USB device would make more
sense for this driver to point to. So converted it to use that instead.
Previously I had made the struct device point to the input device, but
after talking with Dmitry, he said that the USB device would make more
sense for this driver to point to. So converted it to use that instead.
Previously I had made the struct device point to the input device, but
after talking with Dmitry, he said that the USB device would make more
sense for this driver to point to. So converted it to use that instead.
Previously I had made the struct device point to the input device, but
after talking with Dmitry, he said that the USB device would make more
sense for this driver to point to. So converted it to use that instead.
USB: input: keyspan_remote.c: fix up dev_* messages
Previously I had made the struct device point to the input device, but
after talking with Dmitry, he said that the USB device would make more
sense for this driver to point to. So converted it to use that instead.
Previously I had made the struct device point to the input device, but
after talking with Dmitry, he said that the USB device would make more
sense for this driver to point to. So converted it to use that instead.
CC: Dmitry Torokhov <dmitry.torokhov@gmail.com> CC: Axel Lin <axel.lin@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Previously I had made the struct device point to the input device, but
after talking with Dmitry, he said that the USB device would make more
sense for this driver to point to. So converted it to use that instead.
Previously I had made the struct device point to the input device, but
after talking with Dmitry, he said that the USB device would make more
sense for this driver to point to. So converted it to use that instead.
Linus Torvalds [Fri, 4 May 2012 22:13:54 +0000 (15:13 -0700)]
seqlock: add 'raw_seqcount_begin()' function
The normal read_seqcount_begin() function will wait for any current
writers to exit their critical region by looping until the sequence
count is even.
That "wait for sequence count to stabilize" is the right thing to do if
the read-locker will just retry the whole operation on contention: no
point in doing a potentially expensive reader sequence if we know at the
beginning that we'll just end up re-doing it all.
HOWEVER. Some users don't actually retry the operation, but instead
will abort and do the operation with proper locking. So the sequence
count case may be the optimistic quick case, but in the presense of
writers you may want to do full locking in order to guarantee forward
progress. The prime example of this would be the RCU name lookup.
And in that case, you may well be better off without the "retry early",
and are in a rush to instead get to the failure handling. Thus this
"raw" interface that just returns the sequence number without testing it
- it just forces the low bit to zero so that read_seqcount_retry() will
always fail such a "active concurrent writer" scenario.
Linus Torvalds [Fri, 4 May 2012 21:46:02 +0000 (14:46 -0700)]
Fix __read_seqcount_begin() to use ACCESS_ONCE for sequence value read
We really need to use a ACCESS_ONCE() on the sequence value read in
__read_seqcount_begin(), because otherwise the compiler might end up
reloading the value in between the test and the return of it. As a
result, it might end up returning an odd value (which means that a write
is in progress).
If the reader is then fast enough that that odd value is still the
current one when the read_seqcount_retry() is done, we might end up with
a "successful" read sequence, even despite the concurrent write being
active.
In practice this probably never really happens - there just isn't
anything else going on around the read of the sequence count, and the
common case is that we end up having a read barrier immediately
afterwards.
So the code sequence in which gcc might decide to reaload from memory is
small, and there's no reason to believe it would ever actually do the
reload. But if the compiler ever were to decide to do so, it would be
incredibly annoying to debug. Let's just make sure.
Yong Wang [Fri, 4 May 2012 21:02:44 +0000 (14:02 -0700)]
intel_mid_powerbtn: mark irq as IRQF_NO_SUSPEND
So that the power button still wakes up the platform.
Signed-off-by: Pierre Tardy <pierre.tardy@intel.com> Link: http://lkml.kernel.org/r/20120504210244.F2EA5A018B@akpm.mtv.corp.google.com Tested-by: Kangkai Yin <kangkai.yin@intel.com> Tested-by: Yong Wang <yong.y.wang@intel.com> Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Signed-off-by: Alan Cox <alan@linux.intel.com> Cc: Matthew Garrett <mjg@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: H. Peter Anvin <hpa@zytor.com>
arch/x86/platform/geode/net5501.c: change active_low to 0 for LED driver
It seems that there was an error with the active_low = 1 for the
LED, since it should be set to 0 (meaning that active is high,
since 0 is false, hence the confusion.
The wiki article about it confuses it, since it contradicts itself,
regarding what turns on the LED.
I have tested 3.4-rc2 on my net5501 with this patch, and it makes the LED
behave correctly, where "none" turns it off, and "default-on" turns it on,
when echoed onto the trigger "file" in /sys/class/leds.
Signed-off-by: Bjarke Istrup Pedersen <gurligebis@gentoo.org> Link: http://lkml.kernel.org/r/20120504210146.62186A018B@akpm.mtv.corp.google.com Cc: Philip Prindeville <philipp@redfish-solutions.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Stefan Behrens [Fri, 4 May 2012 19:16:07 +0000 (15:16 -0400)]
Btrfs: fix crash in scrub repair code when device is missing
Fix that when scrub tries to repair an I/O or checksum error and one of
the devices containing the mirror is missing, it crashes in bio_add_page
because the bdev is a NULL pointer for missing devices.
Reported-by: Marco L. Crociani <marco.crociani@gmail.com> Signed-off-by: Stefan Behrens <sbehrens@giantdisaster.de> Signed-off-by: Chris Mason <chris.mason@oracle.com>
Alexander Block [Fri, 4 May 2012 19:16:06 +0000 (15:16 -0400)]
btrfs: Fix mismatching struct members in ioctl.h
Fix the size members of btrfs_ioctl_ino_path_args and
btrfs_ioctl_logical_ino_args. The user space btrfs-progs utilities used
__u64 and the kernel headers used __u32 before.
Signed-off-by: Alexander Block <ablock84@googlemail.com> Signed-off-by: Chris Mason <chris.mason@oracle.com>
Josef Bacik [Fri, 4 May 2012 19:16:06 +0000 (15:16 -0400)]
Btrfs: fix page leak when allocing extent buffers
If we happen to alloc a extent buffer and then alloc a page and notice that
page is already attached to an extent buffer, we will only unlock it and
free our existing eb. Any pages currently attached to that eb will be
properly freed, but we don't do the page_cache_release() on the page where
we noticed the other extent buffer which can cause us to leak pages and I
hope cause the weird issues we've been seeing in this area. Thanks,
Signed-off-by: Josef Bacik <josef@redhat.com> Signed-off-by: Chris Mason <chris.mason@oracle.com>
Linus Torvalds [Fri, 4 May 2012 14:57:13 +0000 (07:57 -0700)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Some minor fixes from Intel and a radeon fix.
I have the nouveau fix for the i2c regression queued for next week,
its mostly a revert and seems to work on the system it was originally
introduced for thanks to some i2c core changes."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon: clarify and extend wb setup on APUs and NI+ asics
drm/i915: enable dip before writing data on gen4
fixing dmi match for hp t5745 and hp st5747 thin client
drm/i915: Only enable IPS polling for gen5
drm/i915: Do not read non-existent DPLL registers on PCH hardware
Linus Torvalds [Fri, 4 May 2012 14:50:50 +0000 (07:50 -0700)]
Merge branch 'fix-unmapped-word-at-a-time'
Jana Saout confirmed that this fixes the page faults he saw.
His problem was triggered by ocfs2 and autofs symlink lookups, where the
symlink allocation was at the end of a page. But the deeper reason
seems to be the use of Xen-PV, which is what then causes him to have all
these unmapped pages, which is what then makes it a problem when the
unaligned word-at-a-time code fetches data past the end of a page.
* fix-unmapped-word-at-a-time:
vfs: make word-at-a-time accesses handle a non-existing page
Lukasz Majewski [Fri, 4 May 2012 12:17:10 +0000 (14:17 +0200)]
usb:hsotg:samsung: Use new udc_start and udc_stop callbacks
Replace of deprecated start and stop callbacks with a udc_start and
udc_stop ones.
Now the bind from composite driver is NOT called explicitly, so more
work needs to be done at s3c_udc_probe. Especially enabling SoC clocks
and power for runtime determination of EP number.
After probing, those sources are disabled and enabled again at udc_start
and pullup afterwards.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Sangwook Lee <sangwook.lee@linaro.org> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
This code allows Samsung SoC's to recover its state when
device is disconnected and connected during transfer.
It is necessary, in such a scenario, to reinitialize the USB core
to assure correct initial state of the driver.
This operation is needed since the disconnect interrupt is only
available at HOST mode, which is not supported by this driver.
A simple mechanism with jiffies has been used to perform core reset
only once.
Tested with:
- DFU gadget (various size of the sent data - also packet = MPS)
- Ethernet gadget (CDC and RNDIS)
- Multi Function Gadget (g_multi)
HW:
- Samsung's C210 Universal rev.0
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
Lukasz Majewski [Fri, 4 May 2012 12:17:04 +0000 (14:17 +0200)]
usb:hsotg:samsung: Sending ZLP packet for IN EP0 transfers
This commit targets following scenarios for IN requests:
1. HOST requests e.g. 256B (which is a multiple of MPS = 64B).
Then NO ZLP shall be sent, since host expects exact number of bytes.
2. HOST requested 4096B, but our data for sending is 256B. In this
situation ZLP shall be send to tell HOST that no more data is available
and it shall not wait for more data. This prevents HOST from hanging.
Tested with:
- DFU gadget (various size of the sent data - also packet = MPS)
- Ethernet gadget (CDC and RNDIS)
- Multi Function Gadget (g_multi)
Lukasz Majewski [Fri, 4 May 2012 12:17:02 +0000 (14:17 +0200)]
usb:hsotg:samsung: Use of regulator_bulk_* functions for USB regulators
This commit adds support for supply voltage management for s3c-hsotg IP
block. For that purpose a convenient regulator_bulk_* functions have been
used.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Cc: Mark Brown <broonie@opensource.wolfsonmicro.com> Cc: Liam Girdwood <lrg@ti.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
Paul Zimmerman [Mon, 16 Apr 2012 21:19:06 +0000 (14:19 -0700)]
usb: gadget: add isochronous support to gadget zero
Add two isochronous endpoints to the gadget zero source/sink
function. They are enabled by selecting alternate interface 1, so
by default they are not enabled. Module parameters for setting all
the isoc endpoint characteristics are also provided.
Signed-off-by: Pratyush Anand <pratyush.anand@st.com> Signed-off-by: Paul Zimmerman <paulz@synopsys.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
Dan Carpenter [Tue, 17 Apr 2012 06:30:22 +0000 (09:30 +0300)]
usb: gadget: add a sparse endian notation
The original code works fine, but Sparse complains because it isn't
annotated properly.
drivers/usb/gadget/composite.c:793:26: warning: incorrect type in assignment (different base types)
drivers/usb/gadget/composite.c:793:26: expected unsigned short [unsigned] [usertype] language
devel/drivers/usb/gadget/composite.c:793:26: got restricted __le16 [usertype] <noident>
devel/drivers/usb/gadget/composite.c:795:29: warning: restricted __le16 degrades to integer
drivers/usb/gadget/composite.c:798:24: warning: incorrect type in assignment (different base types)
drivers/usb/gadget/composite.c:798:24: expected restricted __le16 [usertype] <noident>
devel/drivers/usb/gadget/composite.c:798:24: got unsigned short [unsigned] [usertype] language
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
Peter Chen [Sun, 1 Apr 2012 07:17:16 +0000 (15:17 +0800)]
usb: gadget: fsl_udc_core: dTD's next dtd pointer need to be updated once written
dTD's next dtd pointer need to be updated once CPU writes it, or this
request may not be handled by controller, then host will get NAK from
device forever.
This problem occurs when there is a request is handling, we need to add
a new request to dTD list, if this new request is added before the current
one is finished, the new request is intended to added as next dtd pointer
at current dTD, but without wmb(), the dTD's next dtd pointer may not be
updated when the controller reads it. In that case, the controller will
still get Terminate Bit is 1 at dTD's next dtd pointer, that means there is
no next request, then this new request is missed by controller.
CC: <stable@vger.kernel.org> Signed-off-by: Peter Chen <peter.chen@freescale.com> Acked-by: Li Yang <leoli@freescale.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
Yongsul Oh [Tue, 20 Mar 2012 01:38:38 +0000 (10:38 +0900)]
usb: gadget: composite: prevent a memory leak when configuration bind fails
In some USB composite gadget drivers, the configuration's bind function called
by the usb_add_config() calls multiple bind config functions. (for example cdc2
configuration bind function in the cdc_do_config() of the cdc2.c has two
functionality bind config functions.
- the ecm_bind_config() & the acm_bind_config())
In each functionality bind config function, new instance is allocated and
finally added by the usb_add_function().
So if an error occurred during the second functionality bind config (for
example an error occurred at the acm_bind_config() after succeeding of the
ecm_bind_function()), the instance created by the acm_bind_config() cannot be
freed creating a memory leak.
This patch fixes this issue.
Signed-off-by: Yongsul Oh <yongsul96.oh@samsung.com> Acked-by: Michal Nazarewicz <mina86@mina86.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
There are no in-tree fsg_add() users and it has been deprecated
since 2.6.35 [1dc90985d1: fsg_add() renamed to fsg_bind_config()] so
out-of-tree users had more then enough time to convert. Removing.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
usb: gadget: dummy_hcd: allow to free requests on disabled endpoints
ep->desc is set to NULL on endpoint disable. That means once an endpoint
is disabled it is not possible to free requests. In my target gadget I
first disable endpoints to make sure I have no requests on the fly and
then free frequests. On dummy I am leaking memory here.
Since I can't imagine a reason why it should be a bad thing, lets allow
to free requests on disabled endpoints. On removal of composite the ep0
request is removed so lets allow that here as well.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch converts the g_printer to make use of the compoiste framework
for descriptor parsing instead of its own implementation of it.
This gadget contains now one function which is the printer gadget.
Compile tested only.
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc> Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch removes the DUALSPEED macro and makes the HS (and FS) case
the default. This is one little step before composite can be used for
descriptor management.
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc> Signed-off-by: Felipe Balbi <balbi@ti.com>
usb: gadget: imx_udc: convert to new style start/stop
This patches converts the driver into the new style start/stop interface.
As a result the driver no longer uses the static global controller
variable in start/stop code. I kept the gloval controller variable because
it keeps init simple.
Compile tested only.
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc> Signed-off-by: Felipe Balbi <balbi@ti.com>
usb: gadget: fsl_qe_udc: remove not implemented callbacks
All of this callbacks which I remove here are not implemented and return
an error code. The gadget code returns an error code if a callback is
missing so there is no need to implement this twice.
Cc: Li Yang <leoli@freescale.com> Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc> Signed-off-by: Felipe Balbi <balbi@ti.com>
usb: gadget: fsl_qe_udc: convert to new style start/stop
This patches converts the driver into the new style start/stop interface.
As a result the driver no longer uses the static global udc_conroller variable.
Compile tested only.
Cc: Li Yang <leoli@freescale.com> Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc> Signed-off-by: Felipe Balbi <balbi@ti.com>
usb: gadget: atmel_usba_udc: convert to newstyle start/stop interface
This patches converts the driver into the new style start/stop interface.
As a result the driver no longer uses the static global the_udc
variable in start/stop functions. I kept the the_udc variable since it
makes the init code a little simpler.
Someone with hardware might want to look if it possible to move the vbus
irq/toggle_bias code into ->pullup().
Compile tested only.
Cc: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc> Signed-off-by: Felipe Balbi <balbi@ti.com>
usb: gadget: at91_udc: convert to new style start/stop interface
This patches converts the driver into the new style start/stop interface.
As a result the driver no longer uses the static global controller
variable in start/stop functions. I kept the controller variable since it
makes the init code a little simpler.
Compile tested only.
Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc> Signed-off-by: Felipe Balbi <balbi@ti.com>
projects / linux-beck.git / log