This breaks the stack end corruption detection facility.
What that facility does it write a magic value to "end_of_stack()"
and checking to see if it gets overwritten.
"end_of_stack()" is "task_thread_info(p) + 1", which for sparc64 is
the beginning of the FPU register save area.
So once the user uses the FPU, the magic value is overwritten and the
debug checks trigger.
Fix this by making the size explicit.
Due to the size we use for the fpsaved[], gsr[], and xfsr[] arrays we
are limited to 7 levels of FPU state saves. So each FPU register set
is 256 bytes, allocate 256 * 7 for the fpregs area.
Reported-by: Meelis Roos <mroos@linux.ee> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The AES loops in arch/sparc/crypto/aes_glue.c use a scheme where the
key material is preloaded into the FPU registers, and then we loop
over and over doing the crypt operation, reusing those pre-cooked key
registers.
There are intervening blkcipher*() calls between the crypt operation
calls. And those might perform memcpy() and thus also try to use the
FPU.
The sparc64 kernel FPU usage mechanism is designed to allow such
recursive uses, but with a catch.
There has to be a trap between the two FPU using threads of control.
The mechanism works by, when the FPU is already in use by the kernel,
allocating a slot for FPU saving at trap time. Then if, within the
trap handler, we try to use the FPU registers, the pre-trap FPU
register state is saved into the slot. Then at trap return time we
notice this and restore the pre-trap FPU state.
Over the long term there are various more involved ways we can make
this work, but for a quick fix let's take advantage of the fact that
the situation where this happens is very limited.
All sparc64 chips that support the crypto instructiosn also are using
the Niagara4 memcpy routine, and that routine only uses the FPU for
large copies where we can't get the source aligned properly to a
multiple of 8 bytes.
We look to see if the FPU is already in use in this context, and if so
we use the non-large copy path which only uses integer registers.
Furthermore, we also limit this special logic to when we are doing
kernel copy, rather than a user copy.
Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Inconsistently, the raw_* IRQ routines do not interact with and update
the irqflags tracing and lockdep state, whereas the raw_* spinlock
interfaces do.
This causes problems in p1275_cmd_direct() because we disable hardirqs
by hand using raw_local_irq_restore() and then do a raw_spin_lock()
which triggers a lockdep trace because the CPU's hw IRQ state doesn't
match IRQ tracing's internal software copy of that state.
The CPU's irqs are disabled, yet current->hardirqs_enabled is true.
====================
reboot: Restarting system
------------[ cut here ]------------
WARNING: CPU: 0 PID: 1 at kernel/locking/lockdep.c:3536 check_flags+0x7c/0x240()
DEBUG_LOCKS_WARN_ON(current->hardirqs_enabled)
Modules linked in: openpromfs
CPU: 0 PID: 1 Comm: systemd-shutdow Tainted: G W 3.17.0-dirty #145
Call Trace:
[000000000045919c] warn_slowpath_common+0x5c/0xa0
[0000000000459210] warn_slowpath_fmt+0x30/0x40
[000000000048f41c] check_flags+0x7c/0x240
[0000000000493280] lock_acquire+0x20/0x1c0
[0000000000832b70] _raw_spin_lock+0x30/0x60
[000000000068f2fc] p1275_cmd_direct+0x1c/0x60
[000000000068ed28] prom_reboot+0x28/0x40
[000000000043610c] machine_restart+0x4c/0x80
[000000000047d2d4] kernel_restart+0x54/0x80
[000000000047d618] SyS_reboot+0x138/0x200
[00000000004060b4] linux_sparc_syscall32+0x34/0x60
---[ end trace 5c439fe81c05a100 ]---
possible reason: unannotated irqs-off.
irq event stamp: 2010267
hardirqs last enabled at (2010267): [<000000000049a358>] vprintk_emit+0x4b8/0x580
hardirqs last disabled at (2010266): [<0000000000499f08>] vprintk_emit+0x68/0x580
softirqs last enabled at (2010046): [<000000000045d278>] __do_softirq+0x378/0x4a0
softirqs last disabled at (2010039): [<000000000042bf08>] do_softirq_own_stack+0x28/0x40
Resetting ...
====================
Use local_* variables of the hw IRQ interfaces so that IRQ tracing sees
all of our changes.
Reported-by: Meelis Roos <mroos@linux.ee> Tested-by: Meelis Roos <mroos@linux.ee> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we have to split up a flush request into multiple pieces
(in order to avoid the firmware range) we don't specify the
arguments in the right order for the second piece.
Fix the order, or else we get hangs as the code tries to
flush "a lot" of entries and we get lockups like this:
Fixes: 4ca9a23765da ("sparc64: Guard against flushing openfirmware mappings.") Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This makes memset follow the standard (instead of returning 0 on success). This
is needed when certain versions of gcc optimizes around memset calls and assume
that the address argument is preserved in %o0.
Signed-off-by: Andreas Larsson <andreas@gaisler.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have seen an issue with guest boot into LDOM that causes early boot failures
because of no matching rules for node identitity of the memory. I analyzed this
on my T4 and concluded there might not be a solution. I saw the issue in
mainline too when booting into the control/primary domain - with guests
configured. Note, this could be a firmware bug on some older machines.
I'll provide a full explanation of the issues below. Should we not find a
matching BEST latency group for a real address (RA) then we will assume node 0.
On the T4-2 here with the information provided I can't see an alternative.
Technically the LDOM shown below should match the MBLOCK to the
favorable latency group. However other factors must be considered too. Were
the memory controllers configured "fine" grained interleave or "coarse"
grain interleaved - T4. Also should a "group" MD node be considered a NUMA
node?
There has to be at least one Machine Description (MD) "group" and hence one
NUMA node. The group can have one or more latency groups (lg) - more than one
memory controller. The current code chooses the smallest latency as the most
favorable per group. The latency and lg information is in MLGROUP below.
MBLOCK is the base and size of the RAs for the machine as fetched from OBP
/memory "available" property. My machine has one MBLOCK but more would be
possible - with holes?
For a T4-2 the following information has been gathered:
with LDOM guest
MEMBLOCK configuration:
memory size = 0x27f870000
memory.cnt = 0x3
memory[0x0] [0x00000020400000-0x0000029fc67fff], 0x27f868000 bytes
memory[0x1] [0x0000029fd8a000-0x0000029fd8bfff], 0x2000 bytes
memory[0x2] [0x0000029fd92000-0x0000029fd97fff], 0x6000 bytes
reserved.cnt = 0x2
reserved[0x0] [0x00000020800000-0x000000216c15c0], 0xec15c1 bytes
reserved[0x1] [0x00000024800000-0x0000002c180c1e], 0x7980c1f bytes
MBLOCK[0]: base[20000000] size[280000000] offset[0]
(note: "base" and "size" reported in "MBLOCK" encompass the "memory[X]" values)
(note: (RA + offset) & mask = val is the formula to detect a match for the
memory controller. should there be no match for find_node node, a return
value of -1 resulted for the node - BAD)
There is one group. It has these forward links
MLGROUP[1]: node[545] latency[1f7e8] match[200000000] mask[200000000]
MLGROUP[2]: node[54d] latency[2de60] match[0] mask[200000000]
NUMA NODE[0]: node[545] mask[200000000] val[200000000] (latency[1f7e8])
(note: "val" is the best lg's (smallest latency) "match")
there are two groups
group node[16d5]
MLGROUP[0]: node[1765] latency[1f7e8] match[0] mask[200000000]
MLGROUP[3]: node[177d] latency[2de60] match[200000000] mask[200000000]
NUMA NODE[0]: node[1765] mask[200000000] val[0] (latency[1f7e8])
group node[171d]
MLGROUP[2]: node[1775] latency[2de60] match[0] mask[200000000]
MLGROUP[1]: node[176d] latency[1f7e8] match[200000000] mask[200000000]
NUMA NODE[1]: node[176d] mask[200000000] val[200000000] (latency[1f7e8])
(note: for this two "group" bare metal machine, 1/2 memory is in group one's
lg and 1/2 memory is in group two's lg).
Cc: sparclinux@vger.kernel.org Signed-off-by: Bob Picco <bob.picco@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Every path that ends up at do_sparc64_fault() must install a valid
FAULT_CODE_* bitmask in the per-thread fault code byte.
Two paths leading to the label winfix_trampoline (which expects the
FAULT_CODE_* mask in register %g4) were not doing so:
1) For pre-hypervisor TLB protection violation traps, if we took
the 'winfix_trampoline' path we wouldn't have %g4 initialized
with the FAULT_CODE_* value yet. Resulting in using the
TLB_TAG_ACCESS register address value instead.
2) In the TSB miss path, when we notice that we are going to use a
hugepage mapping, but we haven't allocated the hugepage TSB yet, we
still have to take the window fixup case into consideration and
in that particular path we leave %g4 not setup properly.
Errors on this sort were largely invisible previously, but after
commit 4ccb9272892c33ef1c19a783cfa87103b30c2784 ("sparc64: sun4v TLB
error power off events") we now have a fault_code mask bit
(FAULT_CODE_BAD_RA) that triggers due to this bug.
FAULT_CODE_BAD_RA triggers because this bit is set in TLB_TAG_ACCESS
(see #1 above) and thus we get seemingly random bus errors triggered
for user processes.
Fixes: 4ccb9272892c ("sparc64: sun4v TLB error power off events") Reported-by: Meelis Roos <mroos@linux.ee> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We've witnessed a few TLB events causing the machine to power off because
of prom_halt. In one case it was some nfs related area during rmmod. Another
was an mmapper of /dev/mem. A more recent one is an ITLB issue with
a bad pagesize which could be a hardware bug. Bugs happen but we should
attempt to not power off the machine and/or hang it when possible.
This is a DTLB error from an mmapper of /dev/mem:
[root@sparcie ~]# SUN4V-DTLB: Error at TPC[fffff80100903e6c], tl 1
SUN4V-DTLB: TPC<0xfffff80100903e6c>
SUN4V-DTLB: O7[fffff801081979d0]
SUN4V-DTLB: O7<0xfffff801081979d0>
SUN4V-DTLB: vaddr[fffff80100000000] ctx[1250] pte[98000000000f0610] error[2]
.
This is recent mainline for ITLB:
[ 3708.179864] SUN4V-ITLB: TPC<0xfffffc010071cefc>
[ 3708.188866] SUN4V-ITLB: O7[fffffc010071cee8]
[ 3708.197377] SUN4V-ITLB: O7<0xfffffc010071cee8>
[ 3708.206539] SUN4V-ITLB: vaddr[e0003] ctx[1a3c] pte[2900000dcc800eeb] error[4]
.
Normally sun4v_itlb_error_report() and sun4v_dtlb_error_report() would call
prom_halt() and drop us to OF command prompt "ok". This isn't the case for
LDOMs and the machine powers off.
For the HV reported error of HV_ENORADDR for HV HV_MMU_MAP_ADDR_TRAP we cause
a SIGBUS error by qualifying it within do_sparc64_fault() for fault code mask
of FAULT_CODE_BAD_RA. This is done when trap level (%tl) is less or equal
one("1"). Otherwise, for %tl > 1, we proceed eventually to die_if_kernel().
The logic of this patch was partially inspired by David Miller's feedback.
Power off of large sparc64 machines is painful. Plus die_if_kernel provides
more context. A reset sequence isn't a brief period on large sparc64 but
better than power-off/power-on sequence.
Cc: sparclinux@vger.kernel.org Signed-off-by: Bob Picco <bob.picco@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dma_zalloc_coherent() calls dma_alloc_coherent(__GFP_ZERO)
but the sparc32 implementations sbus_alloc_coherent() and
pci32_alloc_coherent() doesn't take the gfp flags into
account.
Tested on the SPARC32/LEON GRETH Ethernet driver which fails
due to dma_alloc_coherent(__GFP_ZERO) returns non zeroed
pages.
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Christopher reports that perf_event_print_debug() can crash in uniprocessor
builds. The crash is due to pcr_ops being NULL.
This happens because pcr_arch_init() is only invoked by smp_cpus_done() which
only executes in SMP builds.
init_hw_perf_events() is closely intertwined with pcr_ops being setup properly,
therefore:
1) Call pcr_arch_init() early on from init_hw_perf_events(), instead of
from smp_cpus_done().
2) Do not hook up a PMU type if pcr_ops is NULL after pcr_arch_init().
3) Move init_hw_perf_events to a later initcall so that it we will be
sure to invoke pcr_arch_init() after all cpus are brought up.
Finally, guard the one naked sequence of pcr_ops dereferences in
__global_pmu_self() with an appropriate NULL check.
Reported-by: Christopher Alexander Tobias Schulze <cat.schulze@alice-dsl.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
XFS has been having trouble with stray delayed allocation extents
beyond EOF for a long time. Recent changes to the collapse range
code has triggered erroneous EBUSY errors on page invalidtion for
block size smaller than page size filesystems. These
have been caused by dirty buffers beyond EOF on a partial page which
do not get written to disk during a sync.
The issue is that write-ahead in xfs_cluster_write() finds such a
partial page and handles it by leaving the page dirty but pushing it
into a writeback state. This used to work just fine, as the
write_cache_pages() code would then find the dirty partial page in
the next mapping tree lookup as the dirty tag is still set.
Unfortunately, when we moved to a mark and sweep approach to
writeback to fix other writeback sync issues, we broken this. THe
act of marking the page as under writeback now clears the TOWRITE
tag in the radix tree, even though the page is still dirty. This
causes the TOWRITE tag to be cleared, and hence the next lookup on
the mapping tree does not find the dirty partial page and so doesn't
try to write it again.
This same writeback bug was found recently in ext4 and fixed in
commit 1c8349a ("ext4: fix data integrity sync in ordered mode")
without communication to the wider filesystem community. We can use
exactly the same fix here so the TOWRITE flag is not cleared on
partial page writes.
cc: stable@vger.kernel.org # dependent on 1c8349a17137b93f0a83f276c764a6df1b9a116e Root-cause-found-by: Brian Foster <bfoster@redhat.com> Signed-off-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: Brian Foster <bfoster@redhat.com> Signed-off-by: Dave Chinner <david@fromorbit.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Christopher Head 2014-06-28 05:26:20 UTC described:
"I tried to reproduce this on 3.12.21. Instead, when I do "echo hello > foo"
in an ecryptfs mount with ecryptfs_xattr specified, I get a kernel crash:
If we create a file when we mount with ecryptfs_xattr_metadata option, we will
encounter a crash in this path:
->ecryptfs_create
->ecryptfs_initialize_file
->ecryptfs_write_metadata
->ecryptfs_write_metadata_to_xattr
->ecryptfs_setxattr
->fsstack_copy_attr_all
It's because our dentry->d_inode used in fsstack_copy_attr_all is NULL, and it
will be initialized when ecryptfs_initialize_file finish.
So we should skip copying attr from lower inode when the value of ->d_inode is
invalid.
The bootloader on the Netgear ReadyNAS RN102 uses Hardware BCH ECC
(strength = 4), while the pxa3xx NAND driver by default uses
Hamming ECC (strength = 1).
This patch changes the ECC mode on these machines to match that
of the bootloader and of the stock firmware. That way, it is
now possible to update the kernel from userland (e.g. using
standard tools from mtd-utils package); u-boot will happily
load and boot it.
Fixes: 92beaccd8b49 ("ARM: mvebu: Enable NAND controller in ReadyNAS 102 .dts file") Signed-off-by: Ben Peddell <klightspeed@killerwolves.net> Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com> Tested-by: Arnaud Ebalard <arno@natisbad.org> Link: https://lkml.kernel.org/r/1410339341-3372-1-git-send-email-klightspeed@killerwolves.net Signed-off-by: Jason Cooper <jason@lakedaemon.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The bootloader on the Netgear ReadyNAS RN2120 uses Hardware BCH
ECC (strength = 4), while the pxa3xx NAND driver by default uses
Hamming ECC (strength = 1).
This patch changes the ECC mode on these machines to match that
of the bootloader and of the stock firmware. That way, it is
now possible to update the kernel from userland (e.g. using
standard tools from mtd-utils package); u-boot will happily
load and boot it.
The issue was initially reported and fixed by Ben Pedell for
RN102. The RN2120 shares the same Hynix H27U1G8F2BTR NAND
flash and setup. This patch is based on Ben's fix for RN102.
The bootloader on the Netgear ReadyNAS RN104 uses Hardware BCH
ECC (strength = 4), while the pxa3xx NAND driver by default uses
Hamming ECC (strength = 1).
This patch changes the ECC mode on these machines to match that
of the bootloader and of the stock firmware. That way, it is
now possible to update the kernel from userland (e.g. using
standard tools from mtd-utils package); u-boot will happily
load and boot it.
The issue was initially reported and fixed by Ben Pedell for
RN102. The RN104 shares the same Hynix H27U1G8F2BTR NAND
flash and setup. This patch is based on Ben's fix for RN102.
As discovered on a custom board similar to at91sam9263ek and basing
its devicetree on that one apparently the pin muxing doesn't get
set up properly. This was discovered since the custom boards u-boot
does funky stuff with the pin muxing and leaved it set to SPI
which made the MMC driver not work under Linux.
The fix is simply to define the given configuration as the default.
This probably worked by pure luck before, but it's better to
make the muxing explicitly set.
Signed-off-by: Andreas Henriksson <andreas.henriksson@endian.se> Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Otherwise the clock for can0 will never get enabled.
Signed-off-by: David Dueck <davidcdueck@googlemail.com> Signed-off-by: Anthony Harivel <anthony.harivel@emtrion.de> Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ELD ALSA control change event is sent by hdmi_present_sense() when
eld_changed is true.
Currently, it is only true when the ELD buffer contents have been
modified. However, the user-visible ELD controls also change to a
zero-length value and back when eld_valid is unset/set, and no event is
currently sent in such cases (such as when unplugging or replugging a
sink).
Fix the code to always set eld_changed if eld_valid value is changed,
and therefore to always send the change event when the user-visible
value changes.
Adding support for Steinberg UR22 USB interface via quirks table patch
See Ubuntu bug report:
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1317244
Also see threads:
http://linux-audio.4202.n7.nabble.com/Support-for-Steinberg-UR22-Yamaha-USB-chipset-0499-1509-tc82888.html#a82917
http://www.steinberg.net/forums/viewtopic.php?t=62290
Tested by at least 4 people judging by the threads.
Did not test MIDI interface, but audio output and capture both are
functional. Built 3.17 kernel with this driver on Ubuntu 14.04 & tested with mpg123
Patch applied to 3.13 Ubuntu kernel works well enough for daily use.
The emu10k1 voice allocator takes voice_lock spinlock. When there is
no empty stream available, it tries to release a voice used by synth,
and calls get_synth_voice. The callback function,
snd_emu10k1_synth_get_voice(), however, also takes the voice_lock,
thus it deadlocks.
The fix is simply removing the voice_lock holds in
snd_emu10k1_synth_get_voice(), as this is always called in the
spinlock context.
The compat_elf_prpsinfo structure does not match the arch/arm struct
elf_pspsinfo definition. As result NT_PRPSINFO note in core file
created by arm64 kernel for aarch32 (compat) process has wrong size.
So gdb cannot display command that caused process crash.
Fix is to change size of __compat_uid_t, __compat_gid_t so it would
match size of similar fields in arch/arm case.
Do full clean up at exit, means terminate all ongoing DMA transfers.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On ima_file_free(), newly created empty files are not labeled with
an initial security.ima value, because the iversion did not change.
Commit dff6efc "fs: fix iversion handling" introduced a change in
iversion behavior. To verify this change use the shell command:
This patch defines the IMA_NEW_FILE flag. The flag is initially
set, when IMA detects that a new file is created, and subsequently
checked on the ima_file_free() hook to set the initial security.ima
value.
rtas_call() accepts and returns values in CPU endianness.
The ddw_query_response and ddw_create_response structs members are
defined and treated as BE but as they are passed to rtas_call() as
(u32 *) and they get byteswapped automatically, the data is CPU-endian.
This fixes ddw_query_response and ddw_create_response definitions and use.
of_read_number() is designed to work with device tree cells - it assumes
the input is big-endian and returns data in CPU-endian. However due
to the ddw_create_response struct fix, create.addr_hi/lo are already
CPU-endian so do not byteswap them.
ddw_avail is a pointer to the "ibm,ddw-applicable" property which contains
3 cells which are big-endian as it is a device tree. rtas_call() accepts
a RTAS token in CPU-endian. This makes use of of_property_read_u32_array
to byte swap and avoid the need for a number of be32_to_cpu calls.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[aik: folded Anton's patch with of_property_read_u32_array] Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru> Acked-by: Anton Blanchard <anton@samba.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit b0c29f79ecea (futexes: Avoid taking the hb->lock if there's
nothing to wake up) changes the futex code to avoid taking a lock when
there are no waiters. This code has been subsequently fixed in commit 11d4616bd07f (futex: revert back to the explicit waiter counting code).
Both the original commit and the fix-up rely on get_futex_key_refs() to
always imply a barrier.
However, for private futexes, none of the cases in the switch statement
of get_futex_key_refs() would be hit and the function completes without
a memory barrier as required before checking the "waiters" in
futex_wake() -> hb_waiters_pending(). The consequence is a race with a
thread waiting on a futex on another CPU, allowing the waker thread to
read "waiters == 0" while the waiter thread to have read "futex_val ==
locked" (in kernel).
Without this fix, the problem (user space deadlocks) can be seen with
Android bionic's mutex implementation on an arm64 multi-cluster system.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Reported-by: Matteo Franchin <Matteo.Franchin@arm.com> Fixes: b0c29f79ecea (futexes: Avoid taking the hb->lock if there's nothing to wake up) Acked-by: Davidlohr Bueso <dave@stgolabs.net> Tested-by: Mike Galbraith <umgwanakikbuti@gmail.com> Cc: Darren Hart <dvhart@linux.intel.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Ingo Molnar <mingo@kernel.org> Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to commit 80af258867648 ("fanotify: groups can specify their
f_flags for new fd"), file descriptors created as part of file access
notification events inherit flags from the event_f_flags argument passed
to syscall fanotify_init(2)[1].
Unfortunately O_CLOEXEC is currently silently ignored.
Indeed, event_f_flags are only given to dentry_open(), which only seems to
care about O_ACCMODE and O_PATH in do_dentry_open(), O_DIRECT in
open_check_o_direct() and O_LARGEFILE in generic_file_open().
It's a pity, since, according to some lookup on various search engines and
http://codesearch.debian.net/, there's already some userspace code which
use O_CLOEXEC:
Additionally, since commit 48149e9d3a7e ("fanotify: check file flags
passed in fanotify_init"). having O_CLOEXEC as part of fanotify_init()
second argument is expressly allowed.
So it seems expected to set close-on-exec flag on the file descriptors if
userspace is allowed to request it with O_CLOEXEC.
But Andrew Morton raised[6] the concern that enabling now close-on-exec
might break existing applications which ask for O_CLOEXEC but expect the
file descriptor to be inherited across exec().
In the other hand, as reported by Mihai Dontu[7] close-on-exec on the file
descriptor returned as part of file access notify can break applications
due to deadlock. So close-on-exec is needed for most applications.
More, applications asking for close-on-exec are likely expecting it to be
enabled, relying on O_CLOEXEC being effective. If not, it might weaken
their security, as noted by Jan Kara[8].
So this patch replaces call to macro get_unused_fd() by a call to function
get_unused_fd_flags() with event_f_flags value as argument. This way
O_CLOEXEC flag in the second argument of fanotify_init(2) syscall is
interpreted and close-on-exec get enabled when requested.
Link: http://lkml.kernel.org/r/cover.1411562410.git.ydroneaud@opteya.com Signed-off-by: Yann Droneaud <ydroneaud@opteya.com> Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed by: Heinrich Schuchardt <xypron.glpk@gmx.de> Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Cc: Mihai Don\u021bu <mihai.dontu@gmail.com> Cc: Pádraig Brady <P@draigBrady.com> Cc: Heinrich Schuchardt <xypron.glpk@gmx.de> Cc: Jan Kara <jack@suse.cz> Cc: Valdis Kletnieks <Valdis.Kletnieks@vt.edu> Cc: Michael Kerrisk-manpages <mtk.manpages@gmail.com> Cc: Lino Sanfilippo <LinoSanfilippo@gmx.de> Cc: Richard Guy Briggs <rgb@redhat.com> Cc: Eric Paris <eparis@redhat.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Michael Kerrisk <mtk.manpages@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 21caf2fc1931 ("mm: teach mm by current context info to not do I/O
during memory allocation") introduces PF_MEMALLOC_NOIO flag to avoid doing
I/O inside memory allocation, __GFP_IO is cleared when this flag is set,
but __GFP_FS implies __GFP_IO, it should also be cleared. Or it may still
run into I/O, like in superblock shrinker. And this will make the kernel
run into the deadlock case described in that commit.
See Dave Chinner's comment about io in superblock shrinker:
Filesystem shrinkers do indeed perform IO from the superblock shrinker and
have for years. Even clean inodes can require IO before they can be freed
- e.g. on an orphan list, need truncation of post-eof blocks, need to
wait for ordered operations to complete before it can be freed, etc.
IOWs, Ext4, btrfs and XFS all can issue and/or block on arbitrary amounts
of IO in the superblock shrinker context. XFS, in particular, has been
doing transactions and IO from the VFS inode cache shrinker since it was
first introduced....
Fix this by clearing __GFP_FS in memalloc_noio_flags(), this function has
masked all the gfp_mask that will be passed into fs for the processes
setting PF_MEMALLOC_NOIO in the direct reclaim path.
v1 thread at: https://lkml.org/lkml/2014/9/3/32
Signed-off-by: Junxiao Bi <junxiao.bi@oracle.com> Cc: Dave Chinner <david@fromorbit.com> Cc: joyce.xue <xuejiufei@huawei.com> Cc: Ming Lei <ming.lei@canonical.com> Cc: Trond Myklebust <trond.myklebust@primarydata.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The l2cap_create_le_flowctl_pdu() function that l2cap_segment_le_sdu()
calls is perfectly capable of doing packet fragmentation if given bigger
PDUs than the HCI buffers allow. Forcing the PDU length based on the HCI
MTU (conn->mtu) would therefore needlessly strict operation on hardware
with limited LE buffers (e.g. both Intel and Broadcom seem to have this
set to just 27 bytes).
This patch removes the restriction and makes it possible to send PDUs of
the full length that the remote MPS value allows.
In this expression: seq = (seq - 1) % 8
seq (u8) is implicitly converted to an int in the arithmetic operation.
So if seq value is 0, operation is ((0 - 1) % 8) => (-1 % 8) => -1.
The new seq value is 0xff which is an invalid ACK value, we expect 0x07.
It leads to frequent dropped ACK and retransmission.
Fix this by using '&' binary operator instead of '%'.
Two bits control TX power on BBP_R1 register. Correct the mask,
otherwise we clear additional bit on BBP_R1 register, what can have
unknown, possible negative effect.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some implementations of modprobe fail to load the driver for a PCI device
automatically because the "interface" part of the modalias from the kernel
is lowercase, and the modalias from file2alias is uppercase.
The "interface" is the low-order byte of the Class Code, defined in PCI
r3.0, Appendix D. Most interface types defined in the spec do not use
alpha characters, so they won't be affected. For example, 00h, 01h, 10h,
20h, etc. are unaffected.
Print the "interface" byte of the Class Code in uppercase hex, as we
already do for the Vendor ID, Device ID, Class, etc.
The Crocodile chip occasionally comes up with 4k and 8k BAR sizes. Due to
an erratum, setting the SR-IOV page size causes the physical function BARs
to expand to the system page size. Since ppc64 uses 64k pages, when Linux
tries to assign the smaller resource sizes to the now 64k BARs the address
will be truncated and the BARs will overlap.
Force Linux to allocate the resource as a full page, which avoids the
overlap.
[bhelgaas: print expanded resource, too] Signed-off-by: Douglas Lehr <dllehr@us.ibm.com> Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Milton Miller <miltonm@us.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Geert Uytterhoeven reported a warning when building pci-mvebu:
drivers/pci/host/pci-mvebu.c: In function 'mvebu_get_tgt_attr':
drivers/pci/host/pci-mvebu.c:887:39: warning: 'rtype' may be used uninitialized in this function [-Wmaybe-uninitialized]
if (slot == PCI_SLOT(devfn) && type == rtype) {
^
And indeed, the code of mvebu_get_tgt_attr() may lead to the usage of rtype
when being uninitialized, even though it would only happen if we had
entries other than I/O space and 32 bits memory space.
This commit fixes that by simply skipping the current DT range being
considered, if it doesn't match the resource type we're looking for.
Commit 2f60ea6b8ced ("NFSv4: The NFSv4.0 client must send RENEW calls if it holds a delegation") set the NFS4_RENEW_TIMEOUT flag in nfs4_renew_state, and does
not put an nfs41_proc_async_sequence call, the NFSv4.1 lease renewal heartbeat
call, on the wire to renew the NFSv4.1 state if the flag was not set.
The NFS4_RENEW_TIMEOUT flag is set when "now" is after the last renewal
(cl_last_renewal) plus the lease time divided by 3. This is arbitrary and
sometimes does the following:
In normal operation, the only way a future state renewal call is put on the
wire is via a call to nfs4_schedule_state_renewal, which schedules a
nfs4_renew_state workqueue task. nfs4_renew_state determines if the
NFS4_RENEW_TIMEOUT should be set, and the calls nfs41_proc_async_sequence,
which only gets sent if the NFS4_RENEW_TIMEOUT flag is set.
Then the nfs41_proc_async_sequence rpc_release function schedules
another state remewal via nfs4_schedule_state_renewal.
Without this change we can get into a state where an application stops
accessing the NFSv4.1 share, state renewal calls stop due to the
NFS4_RENEW_TIMEOUT flag _not_ being set. The only way to recover
from this situation is with a clientid re-establishment, once the application
resumes and the server has timed out the lease and so returns
NFS4ERR_BAD_SESSION on the subsequent SEQUENCE operation.
An example application:
open, lock, write a file.
sleep for 6 * lease (could be less)
ulock, close.
In the above example with NFSv4.1 delegations enabled, without this change,
there are no OP_SEQUENCE state renewal calls during the sleep, and the
clientid is recovered due to lease expiration on the close.
This issue does not occur with NFSv4.1 delegations disabled, nor with
NFSv4.0, with or without delegations enabled.
Signed-off-by: Andy Adamson <andros@netapp.com> Link: http://lkml.kernel.org/r/1411486536-23401-1-git-send-email-andros@netapp.com Fixes: 2f60ea6b8ced (NFSv4: The NFSv4.0 client must send RENEW calls...) Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current open/lock state recovery unfortunately does not handle errors
such as NFS4ERR_CONN_NOT_BOUND_TO_SESSION correctly. Instead of looping,
just proceeds as if the state manager is finished recovering.
This patch ensures that we loop back, handle higher priority errors
and complete the open/lock state recovery.
If a NFSv4.x server returns NFS4ERR_STALE_CLIENTID in response to a
CREATE_SESSION or SETCLIENTID_CONFIRM in order to tell us that it rebooted
a second time, then the client will currently take this to mean that it must
declare all locks to be stale, and hence ineligible for reboot recovery.
RFC3530 and RFC5661 both suggest that the client should instead rely on the
server to respond to inelegible open share, lock and delegation reclaim
requests with NFS4ERR_NO_GRACE in this situation.
If the chosen baud rate is large enough (e.g. 3.5 megabaud), the
calculated n values in serial_omap_is_baud_mode16() may become 0. This
causes a division by zero when calculating the difference between
calculated and desired baud rates. To prevent this, cap the n13 and n16
values on 1.
Division by zero in kernel.
[<c00132e0>] (unwind_backtrace) from [<c00112ec>] (show_stack+0x10/0x14)
[<c00112ec>] (show_stack) from [<c01ed7bc>] (Ldiv0+0x8/0x10)
[<c01ed7bc>] (Ldiv0) from [<c023805c>] (serial_omap_baud_is_mode16+0x4c/0x68)
[<c023805c>] (serial_omap_baud_is_mode16) from [<c02396b4>] (serial_omap_set_termios+0x90/0x8d8)
[<c02396b4>] (serial_omap_set_termios) from [<c0230a0c>] (uart_change_speed+0xa4/0xa8)
[<c0230a0c>] (uart_change_speed) from [<c0231798>] (uart_set_termios+0xa0/0x1fc)
[<c0231798>] (uart_set_termios) from [<c022bb44>] (tty_set_termios+0x248/0x2c0)
[<c022bb44>] (tty_set_termios) from [<c022c17c>] (set_termios+0x248/0x29c)
[<c022c17c>] (set_termios) from [<c022c3e4>] (tty_mode_ioctl+0x1c8/0x4e8)
[<c022c3e4>] (tty_mode_ioctl) from [<c0227e70>] (tty_ioctl+0xa94/0xb18)
[<c0227e70>] (tty_ioctl) from [<c00cf45c>] (do_vfs_ioctl+0x4a0/0x560)
[<c00cf45c>] (do_vfs_ioctl) from [<c00cf568>] (SyS_ioctl+0x4c/0x74)
[<c00cf568>] (SyS_ioctl) from [<c000e480>] (ret_fast_syscall+0x0/0x30)
Signed-off-by: Frans Klaver <frans.klaver@xsens.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fix ensures that we never meet an integer overflow while adding
255 while parsing a variable length encoding. It works differently from
commit 206a81c ("lzo: properly check for overruns") because instead of
ensuring that we don't overrun the input, which is tricky to guarantee
due to many assumptions in the code, it simply checks that the cumulated
number of 255 read cannot overflow by bounding this number.
The MAX_255_COUNT is the maximum number of times we can add 255 to a base
count without overflowing an integer. The multiply will overflow when
multiplying 255 by more than MAXINT/255. The sum will overflow earlier
depending on the base count. Since the base count is taken from a u8
and a few bits, it is safe to assume that it will always be lower than
or equal to 2*255, thus we can always prevent any overflow by accepting
two less 255 steps.
This patch also reduces the CPU overhead and actually increases performance
by 1.1% compared to the initial code, while the previous fix costs 3.1%
(measured on x86_64).
The fix needs to be backported to all currently supported stable kernels.
Reported-by: Willem Pinckaers <willem@lekkertech.net> Cc: "Don A. Bailey" <donb@securitymouse.com> Signed-off-by: Willy Tarreau <w@1wt.eu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a complete description of the LZO format as processed by the
decompressor. I have not found a public specification of this format
hence this analysis, which will be used to better understand the code.
Cc: Willem Pinckaers <willem@lekkertech.net> Cc: "Don A. Bailey" <donb@securitymouse.com> Signed-off-by: Willy Tarreau <w@1wt.eu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit c9fdeb28 removed a 'continue' after checking if the lease needs
to be renewed. However, if client hasn't moved, the code falls down to
starting reboot recovery erroneously (ie., sends open reclaim and gets
back stale_clientid error) before recovering from getting stale_clientid
on the renew operation.
Signed-off-by: Olga Kornievskaia <kolga@netapp.com> Fixes: c9fdeb280b8c (NFS: Add basic migration support to state manager thread) Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
hwreg_present() and hwreg_write() temporarily change the VBR register to
another vector table. This table contains a valid bus error handler
only, all other entries point to arbitrary addresses.
If an interrupt comes in while the temporary table is active, the
processor will start executing at such an arbitrary address, and the
kernel will crash.
While most callers run early, before interrupts are enabled, or
explicitly disable interrupts, Finn Thain pointed out that macsonic has
one callsite that doesn't, causing intermittent boot crashes.
There's another unsafe callsite in hilkbd.
Fix this for good by disabling and restoring interrupts inside
hwreg_present() and hwreg_write().
Explicitly disabling interrupts can be removed from the callsites later.
function 'strncpy' will fill whole buffer 'id.name' of fixed size (32)
with string value and will not leave place for NULL-terminator.
Possible buffer boundaries violation in following string operations.
Replace strncpy with strlcpy.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eliminate the call to BUG_ON() by waiting for the host to respond. We are
trying to reclaim the ownership of memory that was given to the host and so
we will have to wait until the host responds.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Tested-by: Sitsofe Wheeler <sitsofe@yahoo.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eliminate calls to BUG_ON() by properly handling errors. In cases where
rollback is possible, we will return the appropriate error to have the
calling code decide how to rollback state. In the case where we are
transferring ownership of the guest physical pages to the host,
we will wait for the host to respond.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Tested-by: Sitsofe Wheeler <sitsofe@yahoo.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Posting messages to the host can fail because of transient resource
related failures. Correctly deal with these failures and increase the
number of attempts to post the message before giving up.
In this version of the patch, I have normalized the error code to
Linux error code.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Tested-by: Sitsofe Wheeler <sitsofe@yahoo.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
the partial xor result must be kept until the next
tx is generated.
Signed-off-by: Xuelin Shi <xuelin.shi@freescale.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Once calling scsi_host_put, be careful to not access qla_hw_data through
the Scsi_Host private data (ie, scsi_qla_host base_vha).
Fixes: fe1b806f4f71 ("qla2xxx: Refactor shutdown code so some functionality can be reused") Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com> Acked-by: Chad Dupuis <chad.dupuis@qlogic.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using a virtual SCSI disk in a VMWare VM if blkdev_issue_zeroout is used
data can be improperly zeroed out using the mptfusion driver. This patch
disables write_same for this driver and the vmware subsystem_vendor which
ensures that manual zeroing out is used instead.
BugLink: http://bugs.launchpad.net/bugs/1371591 Reported-by: Bruce Lucas <bruce.lucas@mongodb.com> Tested-by: Chris J Arges <chris.j.arges@canonical.com> Signed-off-by: Chris J Arges <chris.j.arges@canonical.com> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dan Carpenter found a issue where be2iscsi would copy the ip
from userspace to the driver buffer before checking the len
of the data being copied:
http://marc.info/?l=linux-scsi&m=140982651504251&w=2
This patch just has us only copy what we the driver buffer
can support.
Tested-by: John Soni Jose <sony.john-n@emulex.com> Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since we cannot make sure the 'val_count' will always be none zero
here, and then if it equals to zero, the kmemdup() will return
ZERO_SIZE_PTR, which equals to ((void *)16).
So this patch fix this with just doing the zero check before calling
kmemdup().
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If LOG_DEVICE is defined and map->dev is NULL it will lead to NULL
pointer dereference. This patch fixes this issue by adding check for
dev->NULL in all such places in regmap.c
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If 'map->dev' is NULL and there will lead dev_name() to be NULL pointer
dereference. So before dev_name(), we need to have check of the map->dev
pionter.
We also should make sure that the 'name' pointer shouldn't be NULL for
debugfs_create_dir(). So here using one default "dummy" debugfs name when
the 'name' pointer and 'map->dev' are both NULL.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case of 8 bit mode and DMA usage we end up with every second byte written as
0. We have to respect bits_per_word settings what this patch actually does.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Quark x1000 advertises PGE via the standard CPUID method
PGE bits exist in Quark X1000's PTEs. In order to flush
an individual PTE it is necessary to reload CR3 irrespective
of the PTE.PGE bit.
See Quark Core_DevMan_001.pdf section 6.4.11
This bug was fixed in Galileo kernels, unfixed vanilla kernels are expected to
crash and burn on this platform.
vcpu ioctls can hang the calling thread if issued while a vcpu is running.
However, invalid ioctls can happen when userspace tries to probe the kind
of file descriptors (e.g. isatty() calls ioctl(TCGETS)); in that case,
we know the ioctl is going to be rejected as invalid anyway and we can
fail before trying to take the vcpu mutex.
This patch does not change functionality, it just makes invalid ioctls
fail faster.
Signed-off-by: David Matlack <dmatlack@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
vcpu exits and memslot mutations can run concurrently as long as the
vcpu does not aquire the slots mutex. Thus it is theoretically possible
for memslots to change underneath a vcpu that is handling an exit.
If we increment the memslot generation number again after
synchronize_srcu_expedited(), vcpus can safely cache memslot generation
without maintaining a single rcu_dereference through an entire vm exit.
And much of the x86/kvm code does not maintain a single rcu_dereference
of the current memslots during each exit.
We can prevent the following case:
vcpu (CPU 0) | thread (CPU 1)
--------------------------------------------+--------------------------
1 vm exit |
2 srcu_read_unlock(&kvm->srcu) |
3 decide to cache something based on |
old memslots |
4 | change memslots
| (increments generation)
5 | synchronize_srcu(&kvm->srcu);
6 retrieve generation # from new memslots |
7 tag cache with new memslot generation |
8 srcu_read_unlock(&kvm->srcu) |
... |
<action based on cache occurs even |
though the caching decision was based |
on the old memslots> |
... |
<action *continues* to occur until next |
memslot generation change, which may |
be never> |
|
By incrementing the generation after synchronizing with kvm->srcu readers,
we ensure that the generation retrieved in (6) will become invalid soon
after (8).
Keeping the existing increment is not strictly necessary, but we
do keep it and just move it for consistency from update_memslots to
install_new_memslots. It invalidates old cached MMIOs immediately,
instead of having to wait for the end of synchronize_srcu_expedited,
which makes the code more clearly correct in case CPU 1 is preempted
right after synchronize_srcu() returns.
To avoid halving the generation space in SPTEs, always presume that the
low bit of the generation is zero when reconstructing a generation number
out of an SPTE. This effectively disables MMIO caching in SPTEs during
the call to synchronize_srcu_expedited. Using the low bit this way is
somewhat like a seqcount---where the protected thing is a cache, and
instead of retrying we can simply punt if we observe the low bit to be 1.
Signed-off-by: David Matlack <dmatlack@google.com> Reviewed-by: Xiao Guangrong <xiaoguangrong@linux.vnet.ibm.com> Reviewed-by: David Matlack <dmatlack@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The following events can lead to an incorrect KVM_EXIT_MMIO bubbling
up to userspace:
(1) Guest accesses gpa X without a memory slot. The gfn is cached in
struct kvm_vcpu_arch (mmio_gfn). On Intel EPT-enabled hosts, KVM sets
the SPTE write-execute-noread so that future accesses cause
EPT_MISCONFIGs.
(2) Host userspace creates a memory slot via KVM_SET_USER_MEMORY_REGION
covering the page just accessed.
(3) Guest attempts to read or write to gpa X again. On Intel, this
generates an EPT_MISCONFIG. The memory slot generation number that
was incremented in (2) would normally take care of this but we fast
path mmio faults through quickly_check_mmio_pf(), which only checks
the per-vcpu mmio cache. Since we hit the cache, KVM passes a
KVM_EXIT_MMIO up to userspace.
This patch fixes the issue by using the memslot generation number
to validate the mmio cache.
Signed-off-by: David Matlack <dmatlack@google.com>
[xiaoguangrong: adjust the code to make it simpler for stable-tree fix.] Signed-off-by: Xiao Guangrong <xiaoguangrong@linux.vnet.ibm.com> Reviewed-by: David Matlack <dmatlack@google.com> Reviewed-by: Xiao Guangrong <xiaoguangrong@linux.vnet.ibm.com> Tested-by: David Matlack <dmatlack@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During an incremental send, when we finish processing an inode (corresponding to
a regular file) we would assume the gap between the end of the last processed file
extent and the file's size corresponded to a file hole, and therefore incorrectly
send a bunch of zero bytes to overwrite that region in the file.
Signed-off-by: Filipe David Borba Manana <fdmanana@gmail.com> Signed-off-by: Chris Mason <clm@fb.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds the PCI id for Intel Quark ILB.
It will be used for GPIO and Multifunction device driver.
Signed-off-by: Josef Ahmad <josef.ahmad@intel.com> Acked-by: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Chang Rebecca Swee Fun <rebecca.swee.fun.chang@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We check whether transid is already committed via last_trans_committed and
then search through trans_list for pending transactions. If
last_trans_committed is updated by btrfs_commit_transaction after we check
it (there is no locking), we will fail to find the committed transaction
and return EINVAL to the caller. This has been observed occasionally by
ceph-osd (which uses this ioctl heavily).
Fix by rechecking whether the provided transid <= last_trans_committed
after the search fails, and if so return 0.
Signed-off-by: Sage Weil <sage@redhat.com> Signed-off-by: Chris Mason <clm@fb.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Marc Merlin sent me a broken fs image months ago where it would blow up in the
upper->checked BUG_ON() in build_backref_tree. This is because we had a
scenario like this
block a -- level 4 (not shared)
|
block b -- level 3 (reloc block, shared)
|
block c -- level 2 (not shared)
|
block d -- level 1 (shared)
|
block e -- level 0 (shared)
We go to build a backref tree for block e, we notice block d is shared and add
it to the list of blocks to lookup it's backrefs for. Now when we loop around
we will check edges for the block, so we will see we looked up block c last
time. So we lookup block d and then see that the block that points to it is
block c and we can just skip that edge since we've already been up this path.
The problem is because we clear need_check when we see block d (as it is shared)
we never add block b as needing to be checked. And because block c is in our
path already we bail out before we walk up to block b and add it to the backref
check list.
To fix this we need to reset need_check if we trip over a block that doesn't
need to be checked. This will make sure that any subsequent blocks in the path
as we're walking up afterwards are added to the list to be processed. With this
patch I can now mount Marc's fs image and it'll complete the balance without
panicing. Thanks,
Reported-by: Marc MERLIN <marc@merlins.org> Signed-off-by: Josef Bacik <jbacik@fb.com> Signed-off-by: Chris Mason <clm@fb.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
test, because it means it couldn't build the backref tree properly. This is
annoying to users and frankly a recoverable error, nothing in this function is
actually fatal since it is just an in-memory building of the backrefs for a
given bytenr. So go through and change all the BUG_ON()'s to ASSERT()'s, and
fix the BUG_ON(!upper->checked) thing to just return an error.
This patch also fixes the error handling so it tears down the work we've done
properly. This code was horribly broken since we always just panic'ed instead
of actually erroring out, so it needed to be completely re-worked. With this
patch my broken image no longer panics when I mount it. Thanks,
Signed-off-by: Josef Bacik <jbacik@fb.com> Signed-off-by: Chris Mason <clm@fb.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When doing log replay we may have to update inodes, which traditionally goes
through our delayed inode stuff. This will try to move space over from the
trans handle, but we don't reserve space in our trans handle on replay since we
don't know how much we will need, so instead we try to flush. But because we
have a trans handle open we won't flush anything, so if we are out of reserve
space we will simply return ENOSPC. Since we know that if an operation made it
into the log then we definitely had space before the box bought the farm then we
don't need to worry about doing this space reservation. Use the
fs_info->log_root_recovering flag to skip the delayed inode stuff and update the
item directly. Thanks,
Signed-off-by: Josef Bacik <jbacik@fb.com> Signed-off-by: Chris Mason <clm@fb.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
An user reported this, it is because that lseek's SEEK_SET/SEEK_CUR/SEEK_END
allow a negative value for @offset, but btrfs's SEEK_DATA/SEEK_HOLE don't
prepare for that and convert the negative @offset into unsigned type,
so we get (end < start) warning.
The behaviour of a 'chattr -c' consists of getting the current flags,
clearing the FS_COMPR_FL bit and then sending the result to the set
flags ioctl - this means the bit FS_NOCOMP_FL isn't set in the flags
passed to the ioctl. This results in the compression property not being
cleared from the inode - it was cleared only if the bit FS_NOCOMP_FL
was set in the received flags.
Reproducer:
$ mkfs.btrfs -f /dev/sdd
$ mount /dev/sdd /mnt && cd /mnt
$ mkdir a
$ chattr +c a
$ touch a/file
$ lsattr a/file
--------c------- a/file
$ chattr -c a
$ touch a/file2
$ lsattr a/file2
--------c------- a/file2
$ lsattr -d a
---------------- a
Reported-by: Andreas Schneider <asn@cryptomilk.org> Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: Chris Mason <clm@fb.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The transaction thread may want to do more work, namely it pokes the
cleaner ktread that will start processing uncleaned subvols.
This can be triggered by user via the 'btrfs fi sync' command, otherwise
there was a delay up to 30 seconds before the cleaner started to clean
old snapshots.
Signed-off-by: David Sterba <dsterba@suse.cz> Signed-off-by: Chris Mason <clm@fb.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Quark X1000 contains two designware derived 8250 serial ports.
Each port has a unique PCI configuration space consisting of
BAR0:UART BAR1:DMA respectively.
Unlike the standard 8250 the register width is 32 bits for RHR,IER etc
The Quark UART has a fundamental clock @ 44.2368 MHz allowing for a
bitrate of up to about 2.76 megabits per second.
buf_0 and buf_1 in caam_hash_state are not next to each other.
Accessing buf_1 is incorrect from &buf_0 with an offset of only
size_of(buf_0). The same issue is also with buflen_0 and buflen_1
if we don't make sure to kill the timer, it could
expire after we have already gated our clocks.
That will trigger a Data Abort exception because
we would try to access register while clock is gated.
Fix that bug.
Fixes 869c597 (usb: musb: dsps: add support for suspend and resume) Tested-by: Dave Gerlach <d-gerlach@ti.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Added support for Ketra N1 wireless interface, which uses the
Silicon Labs' CP2104 USB to UART bridge with customized PID 8946.
Signed-off-by: Joe Savage <joe.savage@goketra.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This full-speed USB device generates spurious remote wakeup event
as soon as USB_DEVICE_REMOTE_WAKEUP feature is set. As the result,
Linux can't enter system suspend and S0ix power saving modes once
this keyboard is used.
This patch tries to introduce USB_QUIRK_IGNORE_REMOTE_WAKEUP quirk.
With this quirk set, wakeup capability will be ignored during
device configure.
This patch could be back-ported to kernels as old as 2.6.39.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix to a problem observed when losing a FIN segment that does not
contain data. In such situations, TLP is unable to recover from
*any* tail loss and instead adds at least PTO ms to the
retransmission process, i.e., RTO = RTO + PTO.
Signed-off-by: Per Hurtig <per.hurtig@kau.se> Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Nandita Dukkipati <nanditad@google.com> Acked-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently association restarts do not take into consideration the
state of the socket. When a restart happens, the current assocation
simply transitions into established state. This creates a condition
where a remote system, through a the restart procedure, may create a
local association that is no way reachable by user. The conditions
to trigger this are as follows:
1) Remote does not acknoledge some data causing data to remain
outstanding.
2) Local application calls close() on the socket. Since data
is still outstanding, the association is placed in SHUTDOWN_PENDING
state. However, the socket is closed.
3) The remote tries to create a new association, triggering a restart
on the local system. The association moves from SHUTDOWN_PENDING
to ESTABLISHED. At this point, it is no longer reachable by
any socket on the local system.
This patch addresses the above situation by moving the newly ESTABLISHED
association into SHUTDOWN-SENT state and bundling a SHUTDOWN after
the COOKIE-ACK chunk. This way, the restarted associate immidiately
enters the shutdown procedure and forces the termination of the
unreachable association.
Reported-by: David Laight <David.Laight@aculab.com> Signed-off-by: Vlad Yasevich <vyasevich@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When team_notify_peers and team_mcast_rejoin are called, they both reset
their respective .count_pending atomic variable. Then when the actual
worker function is executed, the variable is atomically decremented.
This pattern introduces a potential race condition where the
.count_pending rolls over and the worker function keeps rescheduling
until .count_pending decrements to zero again:
Instead of assigning a new value to .count_pending, use atomic_add to
tack-on the additional desired worker function invocations.
Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com> Acked-by: Jiri Pirko <jiri@resnulli.us> Fixes: fc423ff00df3a19554414ee ("team: add peer notification") Fixes: 492b200efdd20b8fcfdac87 ("team: add support for sending multicast rejoins") Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In xmit path, we build a flowi6 which will be used for the output route lookup.
We are sending a GRE packet, neither IPv4 nor IPv6 encapsulated packet, thus the
protocol should be IPPROTO_GRE.
Fixes: c12b395a4664 ("gre: Support GRE over IPv6") Reported-by: Matthieu Ternisien d'Ouville <matthieu.tdo@6wind.com> Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After the packet is successfully sent, we should not touch the skb
as it may have been freed. This patch is based on the work done by
Long Li <longli@microsoft.com>.
In this version of the patch I have fixed issues pointed out by David.
David, please queue this up for stable.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Tested-by: Long Li <longli@microsoft.com> Tested-by: Sitsofe Wheeler <sitsofe@yahoo.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit 8a29111c7ca6 ("net: gro: allow to build full sized skb")
I added a regression for linear skb that traditionally force GRO
to use the frag_list fallback.
Erez Shitrit found that at most two segments were aggregated and
the "if (skb_gro_len(p) != pinfo->gso_size)" test was failing.
This is because pinfo at this spot still points to the last skb in the
chain, instead of the first one, where we find the correct gso_size
information.
Signed-off-by: Eric Dumazet <edumazet@google.com> Fixes: 8a29111c7ca6 ("net: gro: allow to build full sized skb") Reported-by: Erez Shitrit <erezsh@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 8ef29f8aae524bd51298fb10ac6a5ce6c4c5a3d8.
The driver core already calls pinctrl_get() and claims the default
state. There is no need to replicate this in the driver. Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In macvtap device delete and open calls can race and
this causes a list curruption of the vlan queue_list.
The race intself is triggered by the idr accessors
that located the vlan device. The device is stored
into and removed from the idr under both an rtnl and
a mutex. However, when attempting to locate the device
in idr, only a mutex is taken. As a result, once cpu
perfoming a delete may take an rtnl and wait for the mutex,
while another cput doing an open() will take the idr
mutex first to fetch the device pointer and later take
an rtnl to add a queue for the device which may have
just gotten deleted.
With this patch, we now hold the rtnl for the duration
of the macvtap_open() call thus making sure that
open will not race with delete.
CC: Michael S. Tsirkin <mst@redhat.com> CC: Jason Wang <jasowang@redhat.com> Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com> Acked-by: Jason Wang <jasowang@redhat.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently we genarate a queueing route if we have matching policies
but can not resolve the states and the sysctl xfrm_larval_drop is
disabled. Here we assume that dst_output() is called to kill the
queued packets. Unfortunately this assumption is not true in all
cases, so it is possible that these packets leave the system unwanted.
We fix this by generating queueing routes only from the
route lookup functions, here we can guarantee a call to
dst_output() afterwards.
Currently we genarate a blackhole route route whenever we have
matching policies but can not resolve the states. Here we assume
that dst_output() is called to kill the balckholed packets.
Unfortunately this assumption is not true in all cases, so
it is possible that these packets leave the system unwanted.
We fix this by generating blackhole routes only from the
route lookup functions, here we can guarantee a call to
dst_output() afterwards.