Felix Fietkau [Mon, 29 Aug 2011 16:57:54 +0000 (18:57 +0200)]
ath9k: fix checks for first subframe delimiter padding
The commit "ath9k_hw: Fix exceed transmission burst-time of 5GHz" added
a padding of 60 delimiters on the first subframe to work around an issue
on AR9380, but it lacked the checks to prevent it from being applied to
pre-AR9380, enterprise AR9380 or AR9580+
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
This will avoid mac80211 to trigger PS mode for connected station
based on the PM bit of incoming frames. AP firmware is capable of
handling such frames and buffering TX frames destined to the
stations that are in PS mode.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Vivek Natarajan [Mon, 29 Aug 2011 08:53:03 +0000 (14:23 +0530)]
cfg80211/nl80211: Indicate roaming feature capability to userspace.
When the rssi of the current AP drops, both wpa_supplicant and the
firmware may do a background scan to find a better AP and try to
associate. Since firmware based roaming is faster, inform
wpa_supplicant to avoid roaming and let the firmware decide to
roam if necessary.
For fullmac drivers like ath6kl, it is just enough to provide the
ESSID and the firmware will decide on the BSSID. Since it is not
possible to do pre-auth during roaming for fullmac drivers, the
wpa_supplicant needs to completely disconnect with the old AP and
reconnect with the new AP. This consumes lot of time and it is
better to leave the roaming decision to the firmware.
Signed-off-by: Vivek Natarajan <nataraja@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Sun, 28 Aug 2011 19:11:01 +0000 (21:11 +0200)]
mac80211: retry sending failed BAR frames later instead of tearing down aggr
Unfortunately failed BAR tx attempts happen more frequently than I
expected, and the resulting aggregation teardowns cause performance
issues, as the aggregation session does not always get re-established
properly.
Instead of tearing down the entire aggr session, we can simply store the
SSN of the last failed BAR tx attempt, wait for the first successful
tx status event, and then send another BAR with the same SSN.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Cc: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rafał Miłecki [Sun, 28 Aug 2011 16:47:22 +0000 (18:47 +0200)]
ssb: use u16 for storing board rev
Specs say about size 2 (u16) and my 14e4:4727 has board rev 0x1211.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Sat, 27 Aug 2011 23:52:10 +0000 (01:52 +0200)]
ath9k_hw: do not apply the 2.4 ghz ack timeout workaround to cts
It is only used to workaround interoperability issues related to longer
delays in receiving the block ack, so it is not necessary to apply it
to the CTS exchange.
Should improve throughput slightly, especially when there are lots
of retransmissions.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Javier Cardona [Tue, 6 Sep 2011 19:10:43 +0000 (12:10 -0700)]
mac80211: Defer tranmission of mesh path errors
Under failure conditions, the mesh stack sends PERR messages to the
previous sender of the failed frame. This happens in the tx feedback
path, in which the transmission queue lock may be taken. Avoid a
deadlock by sending the path error via the pending queue.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Greg Dietsche [Sun, 28 Aug 2011 13:22:38 +0000 (08:22 -0500)]
iwlwifi: iwl-agn-rs.c: remove old comment
this comment refers to some code that was removed.
Signed-off-by: Greg Dietsche <Gregory.Dietsche@cuw.edu> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Sat, 27 Aug 2011 22:32:25 +0000 (00:32 +0200)]
ath9k: defer ath_tx_setup_buffer setup to the first tx attempt during aggr
With sequence number and buffer allocation deferred to when they're needed
for the first time, it becomes much easier to start dropping packets from
the tid queue if necessary, e.g. when latency suddenly increases. This can
lead to some future improvements in buffer management for better latency.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Sat, 27 Aug 2011 22:32:23 +0000 (00:32 +0200)]
ath9k: move the sequence number from ath_frame_info to ath_buf
It is only necessary for BAW tracking and moving it to the ath_buf
makes it easier to add further improvements, such as deferring
seqno allocation in the aggregation path.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Sat, 27 Aug 2011 22:32:22 +0000 (00:32 +0200)]
ath9k: clean up the aggregation tid queue
Use a sk_buff_head instead containing skbs instead of a list_head
containing ath_bufs. This makes it easier to decouple the aggregation
code from the ath_buf struct
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville [Mon, 29 Aug 2011 19:47:58 +0000 (15:47 -0400)]
wl12xx/sdio_test.c: fix build breakage from WL127X_FW_NAME change
Commit c302b2c959164622558474871ae942da0e484a38 ("wl12xx: Use a single
fw for both STA and AP roles") changed the name of the firmware name
definition, breaking the build of wl12xx/sdio_test.c.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After analysis, this is not a bug, but a false warning. Nonetheless,
a cleanup is in order to prevent some future janitor proposing
the wrong fix, as I did in my original patch.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k: Add debugfs support for mac/baseband samples
This patch keep track of number of samples that includes
DMA debugs registers, PCU observe, CR, channel noise,
cycle conters, noisefloor history buffer and last N number
of tx and rx descriptor status. These samples are grouped
in table manner which dumping in debgufs.
Felix Fietkau [Sat, 27 Aug 2011 08:25:27 +0000 (10:25 +0200)]
ath9k: fix regression in sending aggregated packets
The recent commit "ath9k: Send legacy rated frames as unaggregated"
introduced a check to ensure that packets with non-MCS rates set in
the rate series will not be aggregated. However, it failed to check
if the rate series is valid before testing the flags, thus breaking
aggregation for normal MCS-only packets if the last series is unset.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
For AR9287 v1.3+ chips, MAC runs at 117MHz. But the initvals
IFS parameters are loaded based on 44/88MHz clockrate. So
eifs/usec from ini should not be used for AR9287 v1.3+.
The mentioned values are tested on 2 chain HT40 mode.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Larry Finger [Fri, 26 Aug 2011 18:41:38 +0000 (20:41 +0200)]
b43: Relax requirement for descriptors to be in the DMA zone
When 64-bit DMA was first used, there were problems with the
BCM4311 (14e4:4311). The problem was "fixed" by using the GFP_DMA
flag in the allocation of coherent ring descriptor memory.
The original problem is now believed to have been due to bugs in
the 64-bit DMA implementation in the rest of the kernel, and that
those bugs have been fixed. Accordingly, the requirement for the
descriptors to be in the DMA zone is relaxed.
Bounce buffers are left in the DMA zone.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Michael Buesch <m@bues.ch> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Axel Lin [Fri, 26 Aug 2011 06:34:59 +0000 (14:34 +0800)]
p54spi: add "spi:" prefix for stlc45xx modalias
Since commit e0626e38 (spi: prefix modalias with "spi:"),
the spi modalias is prefixed with "spi:".
This patch adds "spi:" prefix for modalias of stlc45xx.
Also move it to be group with other modalias.
Signed-off-by: Axel Lin <axel.lin@gmail.com> Acked-By: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Fri, 26 Aug 2011 06:13:56 +0000 (23:13 -0700)]
iwlagn: handle GO powersave
In order to implement support for GO powersave on
the P2P client side, the ucode needs to know what
GO we're trying to authenticate/associate with,
it needs to have a station entry and the BSSID in
the RXON set.
Implement the new mac80211 callbacks to give this
data to the device.
Since this is also useful for the device when a
normal connection is established, also program it
with the information in that case.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
This finalizes the move of the data path to the transport layer.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwlagn: move the stop / wake queue logic to transport layer
priv->mac80211_registered and priv->hw needed to move to shared.
stop_queue API was added in order to allow the upper layer to stop
the SW queues for regulatory purposes.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwlagn: move wait_for_tx_queue_empty to transport layer
This one is really transport related.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove a few dereferences of priv from the transport layer while
at it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwlagn: move the disable agg logic to transport layer
Since all the check_empty logic is now in the transport layer,
the upper layer doesn't need to know anything about tx queues.
The disable aggregation flow was the last to know what a tx queue
is, so move it too.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwlagn: move the check_empty logic to the transport layer
This logic is responsible to tell mac80211 when the HW queues are
empty and the BA session can be started / torn down.
Fix a bug on the way:
When the the Tx BA session is stopped and the HW queues aren't empty,
we stop the SW queue to drain the HW queue and then switch to the
legacy HW queue. This is the IWL_EMPTYING_HW_QUEUE_DELBA state.
While in this state, we never wake the SW queue, even when the HW
queue is almost empty, since we need to drain it completely. Look
at iwl_trans_pcie_reclaim regarding this.
Once the HW queue is really empty, we must wake the SW queue in order
to get traffic to the legacy queue.
This step was missing leading to an odd situation were the traffic
would just stall after we tore down a Tx BA session while the HW
queue was not empty.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwlagn: allocate resources for TX BA session in transport
The queues and all the related logic suits to the transport layer.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwlagn: move the mapping ac to queue / fifo to transport
This mapping is transport related.
This allows us to remove the notion of tx queue from the tx path in
the upper layer.
iwl_wake_any_queue moved to transport layer since it needs to access
these mappings.
The TX API is nicer now:
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwlagn: upper layer uses slabs to allocate tx cmds
In a near future, the upper layer won't be aware of the tx queues.
This allows to remove one place where the upper layer needed to
provide the tx queue index to the transport layer.
This also saves around 1.5MB.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
the mapping tx_queue -> fifo is really transport related. The upper
layer should be involved in such things.
Note that upon agg_disable, the queue is always mapped to fifo 0, but
this doesn't matter since when the queue will be setup again for a
new BA session, it will be configured to the good fifo anyway.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwlagn: upper layer stores iwl_rxon_context in skb's CB
This removes the need for iwl_tx_info.
Each tx queue holds an array of skbs, the transport layer doesn't
need to know anything about the context in which a specific skb is
sent.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we remove the module, we free all the tx and rx resources.
Before doing that, we'd better stop the tx / rx activity. Calling
iwl_trans_stop_device in iwl_remove helps also to remove a few API
functions:
* rx_free: happens in iwl_trans_free
* tx_free: happens in iwl_trans_free
* disable_sync_irq: happens in iwl_trans_stop_device
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwlagn: remove dereferences of priv from transport
There are still quite a few, but much less.
A few fields have been moved /copied to hw_params which sits in the
shared area:
* priv->cfg->base_params->num_of_ampdu_queues
* priv->cfg->base_params->shadow_reg_enable
* priv->cfg->sku
* priv->ucode_owner
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
The rate scaling and the transport need to access the data in
iwl_tid_data, hence the move.
Note that the only component in the upper layer that needs this data
is the rate scaling. Refactoring the rate scaling may help to move
iwl_tid_data from the shared area to the transport area.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move all the iwlXXX_abgn_cfg forward declaration to a separate file
so that iwl-pci.c doesn't need to include iwl-agn.h that includes
all iwl-dev.h
This allows to provide real encapsulation. Dereferencing iwl_priv
in the bus layer will now lead to a compilation error.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Daniel Halperin [Fri, 26 Aug 2011 06:11:15 +0000 (23:11 -0700)]
iwlagn: fix compile warnings when CONFIG_PM_SLEEP is not set
CC [M] drivers/net/wireless/iwlwifi/iwl-pci.o
drivers/net/wireless/iwlwifi/iwl-pci.c:506: warning: \91iwl_pci_suspend\92 defined but not used
drivers/net/wireless/iwlwifi/iwl-pci.c:519: warning: \91iwl_pci_resume\92 defined but not used
These are only used if CONFIG_PM_SLEEP is enabled. CONFIG_PM depends
(CONFIG_PM_SLEEP || CONFIG_PM_RUNTIME), so it can be set without
CONFIG_PM_SLEEP selected.
Signed-off-by: Daniel Halperin <dhalperi@cs.washington.edu> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Which means that iwl-io.c doesn't need to include iwl-dev.h any more.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
a few h files weren't self contained. Fix that.
Move iwl_dma_ptr to transport layer since it is not used by the upper layer
any more.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwlagn: iwl-dev.h doesn't include iwl-fh.h any more
Since iwl-fh.h contains transport related data, it shouldn't be included by the
upper layer.
Only the transport layer and iwl-agn-ucode.c includes it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some of them weren't used at all, the others always had the same value since
the driver split.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwlagn: remove references to priv from the transport layer
Continue to the clean up of the priv dereferencing from the transport layer.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwlagn: move dump_csr and dump_fh to transport layer
These are transport layer related. Move also the corresponding debugfs handlers.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since it is needed for host commands only, it is needed in transport layer only
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Change a lot of functions to have them receive iwl_trans and not iwl_priv.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
This helper is used by the transport and the upper layer.
Kill __iwl_free_pages which was used in the transport only.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwlagn: move all iwl_is_XXX helpers to iwl-shared.h
Logic move after all priv->status moved to struct iwl_shared
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
This check can be buggy. IWLAGN_FIRST_AMPDU_QUEUE has to be greater than the
ARRAY_SIZE of iwlagn_ipan_queue_to_tx_fifo.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwlagn: move scd_bc_tbls and scd_base_addr to iwl_trans_pcie
Needed for PCIe only
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now that the reclaim flow has been moved to the transport layer, a lot of
functions can be made static or don't need to be exported outside the transport
layer.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
The reclaim flow is really transport related. Define a simple API to allow the
upper layer to request from the transport layer to reclaim packets until an
index written in the Tx response / BA notification.
The transport layer prepares a list of the packets that are being freed and
passes this list to the upper layer.
Between the two layers, the CB of the skb is used to pass a pointer to the
context (BSS / PAN) in which the skb was sent.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is accessed by the transport layer only, hence the move.
The debugfs handlers that accessed it moved to the transport layer too.
The rx_handlers part of it stayed in the upper layer and a special debugfs
has been added for it
Also add missing includes to iwl-commands.h.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwlagn: move the NIC error flow to the transport layer
It is transport dependent, move to the PCIe transport layer.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the ISR is entirely in the transport layer, its data should be in the pcie
specific region.
Change sync_irq to first disable and then synchronize the IRQ.
iwl_isr and iwl_isr_ict now receive iwl_trans.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwlagn: move iwl_suspend / iwl_resume to the transport layer
These flows needs to access the APM and a few other registers that can differ
between different transports.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since this struct is specific to pcie transport, move it the the pcie
specific transport layer.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwlagn: transport handler can register debugfs entries
Add a handler in iwl_trans_ops to allow it to add entries under debugfs dir
given by the upper level.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rename the recursive inclusion protection in iwl-bus.h while we are at it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove iwl_transport_register which was a W/A. The bus layer knows what
transport to use. So now, the bus layer gives the upper layer a pointer to the
iwl_trans_ops struct that it wants to use. The upper layer then, allocates the
desired transport layer using iwl_trans_ops->alloc function.
As a result of this, priv->trans, no longer exists, priv holds a pointer to
iwl_shared, which holds a pointer to iwl_trans. This required to change all the
calls to the transport layer from upper layer. While we were at it, trans_X
inlines have been renamed to iwl_trans_X to avoid confusions, which of course
required to rename the functions inside the transport layer because of
conflicts in names. So the static API functions inside the transport layer
implementation have been renamed to iwl_trans_pcie_X.
Until now, the IRQ / Tasklet were initialized in iwl_transport_layer. This is
confusing since the registration doesn't mean to request IRQ, so I added a
handler for that.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since it is used by all the layers, it needs to move to iwl_shared.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwlagn: modify the debug macro to be usable by all the layers
Since all the layers need to print debug message, the debug macro cannot suppose
that they will be given iwl_priv as a parameter and then dereference it.
Use iwl_shared instead.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since it is used by all the layers, it needs to move to iwl_shared.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since it is used by all the layers, it needs to move to iwl_shared.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since it is used by all the layers, it needs to move to iwl_shared.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since it is used by all the layers, it needs to move to iwl_shared.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since it is used by all the layers, it needs to move to iwl_shared.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since it is used by all the layers, it needs to move to iwl_shared.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwlagn: introduce struct iwl-shared - known by all layers
This struct will hold pointers to all the layers, so that every layer will find
the pointers it needs when calling another layer.
Note that the drv_data set to struct device is now a pointer to
struct iwl_shared.
This solves of bug that I introduced in
iwlagn: simplify the bus architecture
Bug description:
sysfs gets the the driver data from struct device. Till the aforementioned
patch, dev_get_drvdata would return iwl_priv. After the patch, dev_get_drvdata
return iwl_bus which is buggy since the sysfs handlers rely on this value, and
sysfs handlers need iwl_priv.
Now, dev_get_drvdata return iwl-shared. Since we have pointers to all the
layers in iwl_shared, every layer will be able to get the pointer it needs:
bus layer will gets iwl_bus from the PCI suspend callbacks, and the sysfs
handlers will get the iwl_priv they need.
In order to keep good encapsulation, we need to avoid to dereference iwl_priv
from a different layer. This is why instead of including iwl-dev.h from
iwl-shared.h, I added a forward declaration to iwl_priv. Moreover we keep type
safety while providing encapsulation.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
projects / karo-tx-linux.git / log