Ivo van Doorn [Sun, 28 Oct 2007 13:39:52 +0000 (14:39 +0100)]
rt2x00: Block adhoc & master mode
rt2x00 is broken when it comes down to adhoc and master mode.
The main problem is the beaconing, which is completely failing.
Untill a solution has been found, both beacon requiring modes
must be disabled to prevent numerous bug reports.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Holger Schurig [Tue, 9 Oct 2007 08:41:57 +0000 (10:41 +0200)]
libertas: fixes for slow hardware
Fixes for slow hardware.
Signed-off-by: Vitaly V. Bursov <vitalyvb@ukr.net> Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
The Intel device supported by the hermes driver core is the IPW2011. The
"Intel PRO/Wireless" wording suggests the later Centrino devices and may
be confusing to some users.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Various symptoms depending on the .config options:
- the card stops working after some (short) time
- the card does not work at all
- the card disappears (nothing in lspci/dmesg)
A real power-off is needed to recover the card.
Signed-off-by: Mark Lord <mlord@pobox.com> Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Francois Romieu [Tue, 6 Nov 2007 21:56:10 +0000 (22:56 +0100)]
r8169: do not enable the TBI for the 8168 and the 81x0
The 8168c and the 8100e choke on it. I have not seen an indication
nor received a report that the TBI is being actively used on the
remaining 8168b and 8110. Let's disable it for now until someone
complains.
eric miao [Tue, 30 Oct 2007 01:48:41 +0000 (09:48 +0800)]
add support for smc91x ethernet interface on zylonite
This patch adds LAN91C111 ethernet interface support for zylonite
(a.k.a Marvell's PXA3xx Development Platform) with smc91x driver.
It would be better if a patch would support zylonite along with all
other PXA boards with a single binary of smc91x driver, but it looks
quite difficult for the moment, so ugly #ifdef is still used here.
Signed-off-by: Aleksey Makarov <amakarov@ru.mvista.com> Acked-by: eric miao <eric.miao@marvell.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
The PCI AER support may not work for a couple of reasons.
It may not be configured into the kernel or there may be a BIOS
bug that prevents MMCONFIG from working. If MMCONFIG doesn't work
then the PCI registers that control AER will not be accessible via
pci_read_config functions; luckly there is another window to access
PCI space in the device, so use that.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
The D-Link PCI-X board (and maybe others) can lie about status
ring entries. It seems it will update the register for last status
index before completing the DMA for the ring entry. To avoid reading
stale data, zap the old entry and check.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
David Miller [Wed, 7 Nov 2007 05:13:56 +0000 (21:13 -0800)]
[FUTEX] Fix address computation in compat code.
compat_exit_robust_list() computes a pointer to the
futex entry in userspace as follows:
(void __user *)entry + futex_offset
'entry' is a 'struct robust_list __user *', and
'futex_offset' is a 'compat_long_t' (typically a 's32').
Things explode if the 32-bit sign bit is set in futex_offset.
Type promotion sign extends futex_offset to a 64-bit value before
adding it to 'entry'.
This triggered a problem on sparc64 running 32-bit applications which
would lock up a cpu looping forever in the fault handling for the
userspace load in handle_futex_death().
Compat userspace runs with address masking (wherein the cpu zeros out
the top 32-bits of every effective address given to a memory operation
instruction) so the sparc64 fault handler accounts for this by
zero'ing out the top 32-bits of the fault address too.
Since the kernel properly uses the compat_uptr interfaces, kernel side
accesses to compat userspace work too since they will only use
addresses with the top 32-bit clear.
Because of this compat futex layer bug we get into the following loop
when executing the get_user() load near the top of handle_futex_death():
1) load from address '0xfffffffff7f16bd8', FAULT
2) fault handler clears upper 32-bits, processes fault
for address '0xf7f16bd8' which succeeds
3) goto #1
I want to thank Bernd Zeimetz, Josip Rodin, and Fabio Massimo Di Nitto
for their tireless efforts helping me track down this bug.
Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 9 Nov 2007 23:28:11 +0000 (15:28 -0800)]
Merge branch 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] IOSAPIC bogus error cleanup
[IA64] Update printing of feature set bits
[IA64] Fix IOSAPIC delivery mode setting
[IA64] XPC heartbeat timer function must run on CPU 0
[IA64] Clean up /proc/interrupts output
[IA64] Disable/re-enable CPE interrupts on Altix
[IA64] Clean-up McKinley Errata message
[IA64] Add gate.lds to list of files ignored by Git
[IA64] Fix section mismatch in contig.c version of per_cpu_init()
[IA64] Wrong args to memset in efi_gettimeofday()
[IA64] Remove duplicate includes from ia32priv.h
[IA64] fix number of bytes zeroed by sys_fw_init() in arch/ia64/hp/sim/boot/fw-emu.c
[IA64] Fix perfmon sysctl directory modes
* master.kernel.org:/pub/scm/linux/kernel/git/lethal/sh-2.6: (26 commits)
sh: remove dead config symbols from SH code
sh: Kill off broken snapgear ds1302 code.
sh: Add a dummy vga.h.
rtc: rtc-sh: Zero out tm value for invalid rtc states.
rtc: sh-rtc: Handle rtc_device_register() failure properly.
sh: Fix heartbeart on Solution Engine series
sh: Remove SCI_NPORTS from sh-sci.h
sh: Fix up PAGE_KERNEL_PCC() for nommu.
sh: hs7751rvoip: Kill off dead IPR IRQ mappings.
sh: hs7751rvoip: irq.c needs linux/interrupt.h.
sh: Kill off __{copy,clear}_user_page().
sh: Optimized copy_{to,from}_user_page() for SH-4.
sh: Wire up clear_user_highpage().
sh: Kill off the remaining ST40 cruft.
superhyway: Handle device_register() retval properly.
sh: kgdb sysrq depends on magic sysrq.
sh: Add -Werror for clean directories.
sh: Fix up kgdb build with modular sh-sci.
sh: Export __{s,u}divsi3_i4i on all CPUs.
sh: Fix up kgdb-on-NMI branch target.
...
Linus Torvalds [Fri, 9 Nov 2007 23:16:52 +0000 (15:16 -0800)]
Merge branch 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (37 commits)
[POWERPC] EEH: Make sure warning message is printed
[POWERPC] Make altivec code in swsusp_32.S depend on CONFIG_ALTIVEC
[POWERPC] windfarm: Fix windfarm thread freezer interaction
[POWERPC] Fix si_addr value on low level hash failures
[POWERPC] Refresh ppc64_defconfig and enable pasemi-related options
[POWERPC] pasemi: Update defconfig
[POWERPC] iSeries: Fix ref counting in vio setup
[POWERPC] ] Fix memset size error
[POWERPC] Fix link errors for allyesconfig
[POWERPC] iSeries_init_IRQ non-PCI tidy
[POWERPC] Change fallocate to match unistd.h on powerpc
[POWERPC] EEH: Avoid crash on null device
[POWERPC] EEH: Drivers that need reset trump others
[POWERPC] EEH: Clean up comments
[POWERPC] Fix off-by-one error in setting decrementer on Book E/4xx (v2)
[POWERPC] Fix switch_slb handling of 1T ESID values
[POWERPC] Fix build failure when CONFIG_VIRT_CPU_ACCOUNTING is not defined
[POWERPC] Include udbg.h when using udbg_printf
[POWERPC] Fix cache line vs. block size confusion
[POWERPC] Fix sysctl table check failure on PowerMac
...
Alan Cox [Wed, 7 Nov 2007 16:53:00 +0000 (16:53 +0000)]
frv: Remove bogus NO_IRQ = -1 define
The old NO_IRQ define some platforms had was long ago declared obsolete
and wrong. FRV should therefore not be re-introducing this, especially as
IRQs are usually unsigned in the kernel. The "no IRQ" case is defined to be
zero and Linus made this rather clear at the time.
arch/frv shows no dependancy on this but it might show up driver fixes
needing doing I guess
Signed-off-by: Alan Cox <alan@redhat.com> Acked-by: David Howells <dhowells@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 9 Nov 2007 23:08:37 +0000 (15:08 -0800)]
Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SPARC64]: Use "is_power_of_2" macro for simplicity.
[SPARC]: Remove duplicate includes.
Linus Torvalds [Fri, 9 Nov 2007 23:02:43 +0000 (15:02 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/selinux-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/selinux-2.6:
SELinux: add more validity checks on policy load
SELinux: fix bug in new ebitmap code.
SELinux: suppress a warning for 64k pages.
Peter Zijlstra [Fri, 9 Nov 2007 21:39:39 +0000 (22:39 +0100)]
sched: avoid large irq-latencies in smp-balancing
SMP balancing is done with IRQs disabled and can iterate the full rq.
When rqs are large this can cause large irq-latencies. Limit the nr of
iterations on each run.
This fixes a scheduling latency regression reported by the -rt folks.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Acked-by: Steven Rostedt <rostedt@goodmis.org> Tested-by: Gregory Haskins <ghaskins@novell.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
sched: fix copy_namespace() <-> sched_fork() dependency in do_fork
Sukadev Bhattiprolu reported a kernel crash with control groups.
There are couple of problems discovered by Suka's test:
- The test requires the cgroup filesystem to be mounted with
atleast the cpu and ns options (i.e both namespace and cpu
controllers are active in the same hierarchy).
# mkdir /dev/cpuctl
# mount -t cgroup -ocpu,ns none cpuctl
(or simply)
# mount -t cgroup none cpuctl -> Will activate all controllers
in same hierarchy.
- The test invokes clone() with CLONE_NEWNS set. This causes a a new child
to be created, also a new group (do_fork->copy_namespaces->ns_cgroup_clone->
cgroup_clone) and the child is attached to the new group (cgroup_clone->
attach_task->sched_move_task). At this point in time, the child's scheduler
related fields are uninitialized (including its on_rq field, which it has
inherited from parent). As a result sched_move_task thinks its on
runqueue, when it isn't.
As a solution to this problem, I moved sched_fork() call, which
initializes scheduler related fields on a new task, before
copy_namespaces(). I am not sure though whether moving up will
cause other side-effects. Do you see any issue?
- The second problem exposed by this test is that task_new_fair()
assumes that parent and child will be part of the same group (which
needn't be as this test shows). As a result, cfs_rq->curr can be NULL
for the child.
The solution is to test for curr pointer being NULL in
task_new_fair().
With the patch below, I could run ns_exec() fine w/o a crash.
Ingo Molnar [Fri, 9 Nov 2007 21:39:39 +0000 (22:39 +0100)]
sched: turn off PREEMPT_RESTRICT
PREEMPT_RESTRICT was a method aimed at reducing the amount of wakeup
related preemption. It has a disadvantage though, it can prevent
legitimate wakeups if a task is 'unlucky' to be hit too early by a tick
that clears peer_preempt.
Now that the wakeup preemption has been cleaned up we dont seem to have
excessive preemptions anymore, so this feature can be turned off. (and
removed in the next patch)
Ingo Molnar [Fri, 9 Nov 2007 21:39:38 +0000 (22:39 +0100)]
KVM: fix !SMP build error
fix a !SMP build error:
drivers/kvm/kvm_main.c: In function 'kvm_flush_remote_tlbs':
drivers/kvm/kvm_main.c:220: error: implicit declaration of function 'smp_call_function_mask'
(and also avoid unused function warning related to up_smp_call_function()
not making use of the 'func' parameter.)
Ingo Molnar [Fri, 9 Nov 2007 21:39:38 +0000 (22:39 +0100)]
sched: reintroduce SMP tunings again
Yanmin Zhang reported an aim7 regression and bisected it down to:
| commit 38ad464d410dadceda1563f36bdb0be7fe4c8938
| Author: Ingo Molnar <mingo@elte.hu>
| Date: Mon Oct 15 17:00:02 2007 +0200
|
| sched: uniform tunings
|
| use the same defaults on both UP and SMP.
fix this by reintroducing similar SMP tunings again. This resolves
the regression.
(also update the comments to match the ilog2(nr_cpus) tuning effect)
Paul Mackerras [Fri, 9 Nov 2007 21:39:38 +0000 (22:39 +0100)]
sched: restore deterministic CPU accounting on powerpc
Since powerpc started using CONFIG_GENERIC_CLOCKEVENTS, the
deterministic CPU accounting (CONFIG_VIRT_CPU_ACCOUNTING) has been
broken on powerpc, because we end up counting user time twice: once in
timer_interrupt() and once in update_process_times().
This fixes the problem by pulling the code in update_process_times
that updates utime and stime into a separate function called
account_process_tick. If CONFIG_VIRT_CPU_ACCOUNTING is not defined,
there is a version of account_process_tick in kernel/timer.c that
simply accounts a whole tick to either utime or stime as before. If
CONFIG_VIRT_CPU_ACCOUNTING is defined, then arch code gets to
implement account_process_tick.
This also lets us simplify the s390 code a bit; it means that the s390
timer interrupt can now call update_process_times even when
CONFIG_VIRT_CPU_ACCOUNTING is turned on, and can just implement a
suitable account_process_tick().
account_process_tick() now takes the task_struct * as an argument.
Tested both with and without CONFIG_VIRT_CPU_ACCOUNTING.
Signed-off-by: Paul Mackerras <paulus@samba.org> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Balbir Singh [Fri, 9 Nov 2007 21:39:37 +0000 (22:39 +0100)]
sched: fix delay accounting regression
Fix the delay accounting regression introduced by commit 75d4ef16a6aa84f708188bada182315f80aab6fa. rq no longer has sched_info
data associated with it. task_struct sched_info structure is used by delay
accounting to provide back statistics to user space.
also remove direct use of sched_clock() (which is not a valid thing to
do anymore) and use rq->clock instead.
Peter Zijlstra [Fri, 9 Nov 2007 21:39:37 +0000 (22:39 +0100)]
sched: reintroduce the sched_min_granularity tunable
we lost the sched_min_granularity tunable to a clever optimization
that uses the sched_latency/min_granularity ratio - but the ratio
is quite unintuitive to users and can also crash the kernel if the
ratio is set to 0. So reintroduce the min_granularity tunable,
while keeping the ratio maintained internally.
no functionality changed.
[ mingo@elte.hu: some fixlets. ]
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Russ Anderson [Tue, 16 Oct 2007 22:02:38 +0000 (17:02 -0500)]
[IA64] Update printing of feature set bits
Newer Itanium versions have added additional processor feature set
bits. This patch prints all the implemented feature set bits. Some
bit descriptions have not been made public. For those bits, a generic
"Feature set X bit Y" message is printed. Bits that are not implemented
will no longer be printed.
Signed-off-by: Russ Anderson <rja@sgi.com> Signed-off-by: Tony Luck <tony.luck@intel.com>
Kenji Kaneshige [Wed, 7 Nov 2007 06:38:30 +0000 (15:38 +0900)]
[IA64] Fix IOSAPIC delivery mode setting
Fix the problem that redirect hit bit in I/O SAPIC RTE is set even
when it must be disabled (e.g. nointroute boot option is set, CPU
hotplug is enabled or percpu vector is enabled).
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com> Signed-off-by: Tony Luck <tony.luck@intel.com>
Dean Nelson [Wed, 7 Nov 2007 13:53:06 +0000 (07:53 -0600)]
[IA64] XPC heartbeat timer function must run on CPU 0
Currently, XPC's heartbeat timer function runs on whatever CPU modprobe/insmod
ran on when XPC was started. To avoid the heartbeat from being delayed for
long periods the timer function must run on CPU 0.
N.B. Altix doesn't currently allow cpu0 to be taken offline, so this is
safe for now. This code must be revised when offline of cpu0 is enabled.
Signed-off-by: Dean Nelson <dcn@sgi.com> Signed-off-by: Tony Luck <tony.luck@intel.com>
Jens Axboe [Fri, 9 Nov 2007 11:52:45 +0000 (12:52 +0100)]
block: fix requeue handling in blk_queue_invalidate_tags()
Credit goes to juergen.kadidlo@exasol.com for diagnosing this issue
and supplying the initial patch.
blk_queue_invalidate_tags() must use the proper requeueing paths instead
of open coding the re-add of the request, otherwise we bug out in rq
accounting. Just switch to using blk_requeue_request(), that takes care
of end-tag handling as well and also adds the blktrace REQUEUE notify
event that is also appropriate here.
Russell King [Thu, 8 Nov 2007 23:35:46 +0000 (23:35 +0000)]
[ARM] pxa: fix one-shot timer mode
One-shot timer mode on PXA has various bugs which prevent kernels
build with NO_HZ enabled booting. They end up spinning on a
permanently asserted timer interrupt because we don't properly
clear it down - clearing the OIER bit does not stop the pending
interrupt status. Fix this in the set_mode handler as well.
Moreover, the code which sets the next expiry point may race with
the hardware, and we might not set the match register sufficiently
in the future. If we encounter that situation, return -ETIME so
the generic time code retries.
Acked-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Nicolas Pitre <nico@cam.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Jan Rinze [Thu, 8 Nov 2007 20:51:05 +0000 (21:51 +0100)]
[ARM] 4645/1: Cyberpro: Trivial fix to restore 16bpp mode.
Cyberpro: when user requests 16bpp, use it and not 24bpp.
There was a missing break causing requests for 16bpp mode
to end up in 24bpp mode.
Signed-off-by: Jan Rinze Peterzon <janrinze@home.nl> Acked-by: Ralph Siemsen <ralphs@netwinder.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Benny Halevy [Thu, 8 Nov 2007 13:34:09 +0000 (21:34 +0800)]
[LIB] crc32c: Keep intermediate crc state in cpu order
crypto/crc32.c:chksum_final() is computing the digest as
*(__le32 *)out = ~cpu_to_le32(mctx->crc);
so the low-level crc32c_le routines should just keep
the crc in cpu order, otherwise it is getting swabbed
one too many times on big-endian machines.
Signed-off-by: Benny Halevy <bhalevy@fs1.bhalevy.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Kevin Hilman [Thu, 8 Nov 2007 00:48:16 +0000 (01:48 +0100)]
[ARM] 4644/2: fix flush_kern_tlb_range() in module space
For kernel addresses between TASK_SIZE and PAGE_OFFSET,
flush_tlb_kern_range() does not work as would be expected.
The TLB invalidate works with a matching ASID, or on entries marked as
global. The set_pte_at() macro marks addresses >= PAGE_OFFSET as
global, but not addresses from TASK_SIZE to PAGE_OFFSET, which are
also kernel addresses.
The result is that the entries in this range are not actually
invalidated by flush_tlb_kern_range().
This patch instead marks addresses >= TASK_SIZE as global.
Signed-off-by: Satoru Fujii <s-fujii@ct.jp.nec.com> Signed-off-by: Kevin Hilman <khilman@mvista.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tejun Heo [Thu, 8 Nov 2007 07:00:24 +0000 (08:00 +0100)]
pktcdvd: fix BUG caused by sysfs module reference semantics change
pkt_setup_dev() expects module reference to be held on invocation.
This used to be true for sysfs callbacks but not anymore. Test and
grab module reference around pkt_setup_dev() in
class_pktcdvd_store_add().
Johannes Berg [Wed, 7 Nov 2007 12:59:44 +0000 (23:59 +1100)]
[POWERPC] Make altivec code in swsusp_32.S depend on CONFIG_ALTIVEC
This makes the altivec code in swsusp_32.S depend on CONFIG_ALTIVEC to
avoid build failures for systems that don't have altivec. I'm not sure
whether the code will actually work for other systems, but it was merged
for just ppc32 rather than powermac a very long time ago.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Paul Mackerras <paulus@samba.org>
When I fixed the windfarm freezer interaction first in commit 1ed2ddf380e19dafeec2150ca709ef7f4a67cd21, an earlier patch than the one
I came up with after comments was committed. This has come back to haunt
us now because commit d5d8c5976d6adeddb8208c240460411e2198b393 changed
the freezer to no long send signals. Fix it by removing the windfarm
thread's signal logic and restoring the original try_to_freeze().
We could simply revert 1ed2ddf380e19dafeec2150ca709ef7f4a67cd21 now
but I feel that the assertion that no signal is delivered to the
windfarm thread needs not be there.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Acked-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Paul Mackerras <paulus@samba.org>
[POWERPC] Fix si_addr value on low level hash failures
If the low level MMU hash table insertion returns an error (which
can happen in some rare circumstances when the hypervisor refuses
the insertion of a PTE, typically if you try to access junk via
/dev/mem), the generated signal had an incorrect si_addr value due
to a bug in the assembly, which was loading it as a 32 bits quantity
instead of a 64 bits quantity.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Li Zefan [Mon, 5 Nov 2007 02:21:56 +0000 (13:21 +1100)]
[POWERPC] ] Fix memset size error
The size passing to memset is wrong.
Signed-off-by Li Zefan <lizf@cn.fujitsu.com> Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
An allyesconfig build creates a .text section that is so big that the
.text.init.refok and .fixup sections are too far away for the relocations
to be fixed up correctly. This patch fixes that by linking all the
relevent text sections for each file together.
Suggested by Paul Mackerras.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
Paul Mackerras [Wed, 31 Oct 2007 11:25:35 +0000 (22:25 +1100)]
[POWERPC] Fix off-by-one error in setting decrementer on Book E/4xx (v2)
The decrementer in Book E and 4xx processors interrupts on the
transition from 1 to 0, rather than on the 0 to -1 transition as on
64-bit server and 32-bit "classic" (6xx/7xx/7xxx) processors. At the
moment we subtract 1 from the count of how many decrementer ticks are
required before the next interrupt before putting it into the
decrementer, which is correct for server/classic processors, but could
possibly cause the interrupt to happen too early on Book E and 4xx if
the timebase/decrementer frequency is low.
This fixes the problem by making set_dec subtract 1 from the count for
server and classic processors, instead of having the callers subtract
1. Since set_dec already had a bunch of ifdefs to handle different
processor types, there is no net increase in ugliness. :)
Note that calling set_dec(0) may not generate an interrupt on some
processors. To make sure that decrementer_set_next_event always calls
set_dec with an interval of at least 1 tick, we set min_delta_ns of
the decrementer_clockevent to correspond to 2 ticks (2 rather than 1
to compensate for truncations in the conversions between ticks and
ns).
This also removes a redundant call to set the decrementer to
0x7fffffff - it was already set to that earlier in timer_interrupt.
will schmidt [Tue, 30 Oct 2007 18:59:33 +0000 (05:59 +1100)]
[POWERPC] Fix switch_slb handling of 1T ESID values
Now that we have 1TB segment size support, we need to be using the
GET_ESID_1T macro when comparing ESID values for pc, stack, and
unmapped_base within switch_slb(). A new helper function called
esids_match() contains the logic for deciding when to call GET_ESID
and GET_ESID_1T.
This fixes a duplicate-slb-entry inspired machine-check exception I
was seeing when trying to run java on a power6 partition.
Tested on power6 and power5.
Signed-off-by: Will Schmidt <will_schmidt@vnet.ibm.com> Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Tony Breeds [Tue, 30 Oct 2007 03:55:04 +0000 (14:55 +1100)]
[POWERPC] Fix build failure when CONFIG_VIRT_CPU_ACCOUNTING is not defined
Without this patch I get the following build failure
CC arch/powerpc/platforms/celleb/setup.o
arch/powerpc/platforms/celleb/setup.c:151: error: 'generic_calibrate_decr' undeclared here (not in a function)
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com> Acked-by: Arnd Bergmann <arnd.bergmann@de.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
will schmidt [Mon, 29 Oct 2007 19:24:19 +0000 (06:24 +1100)]
[POWERPC] Include udbg.h when using udbg_printf
This fixes the error
error: implicit declaration of function "udbg_printf"
We have a few spots where we reference udbg_printf() without #including
udbg.h. These are within #ifdef DEBUG blocks, so unnoticed until we do
a #define DEBUG or #define DEBUG_LOW nearby.
Signed-off-by: Will Schmidt <will_schmidt@vnet.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
We had an historical confusion in the kernel between cache line
and cache block size. The former is an implementation detail of
the L1 cache which can be useful for performance optimisations,
the later is the actual size on which the cache control
instructions operate, which can be different.
For some reason, we had a weird hack reading the right property
on powermac and the wrong one on any other 64 bits (32 bits is
unaffected as it only uses the cputable for cache block size
infos at this stage).
This fixes the booting-without-of.txt documentation to mention
the right properties, and fixes the 64 bits initialization code
to look for the block size first, with a fallback to the line
size if the property is missing.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Olof Johansson [Sat, 27 Oct 2007 17:28:51 +0000 (04:28 +1100)]
[POWERPC] Fix CONFIG_SMP=n build break
Fix two build errors on powerpc allyesconfig + CONFIG_SMP=n:
arch/powerpc/platforms/built-in.o: In function `cpu_affinity_set':
arch/powerpc/platforms/cell/spu_priv1_mmio.c:78: undefined reference to `.iic_get_target_id'
arch/powerpc/platforms/built-in.o: In function `iic_init_IRQ':
arch/powerpc/platforms/cell/interrupt.c:397: undefined reference to `.iic_setup_cpu'
Signed-off-by: Olof Johansson <olof@lixom.net> Acked-by: Arnd Bergmann <arnd.bergmann@de.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
Scott Wood [Wed, 24 Oct 2007 16:56:28 +0000 (02:56 +1000)]
[POWERPC] bootwrapper: Revert ps3 binary flag usage, and remove .bin suffix
The ps3 target produces two images, and the binary one is not the
"primary" image that corresponds to the -o flag; thus, it no longer
uses the generic binary flag.
On platforms which do use the binary flag, it no longer produces a
.bin suffix, so that the output file matches what was passed to the -o flag.
This should fix the zImage ln problems for the ps3 target.
Signed-off-by: Scott Wood <scottwood@freescale.com> Acked-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
Dale Farnsworth [Tue, 23 Oct 2007 19:20:32 +0000 (05:20 +1000)]
[POWERPC] Fix mv643xx_pci sysfs .read and .write functions
Commit 91a69029 introduced an additional parameter to the .read and .write
methods for sysfs binary attributes. Two mv64x60_pci functions
were missed in that patch, resulting in these errors:
/cache/git/linux-2.6/arch/powerpc/sysdev/mv64x60_pci.c:77: warning: initialization from incompatible pointer type
/cache/git/linux-2.6/arch/powerpc/sysdev/mv64x60_pci.c:78: warning: initialization from incompatible pointer type
Add the missing "struct bin_attribute *" parameter.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Michael Ellerman [Tue, 23 Oct 2007 04:23:44 +0000 (14:23 +1000)]
[POWERPC] Read back MSI message in rtas_setup_msi_irqs() so restore works
There are plans afoot to use pci_restore_msi_state() to restore MSI
state after a device reset. In order for this to work for the RTAS MSI
backend, we need to read back the MSI message from config space after
it has been setup by firmware.
This should be sufficient for restoring the MSI state after a device
reset, however we will need to revisit this for suspend to disk if that
is ever implemented on pseries.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Acked-by: Linas Vepstas <linas@austin.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
Olof Johansson [Sat, 20 Oct 2007 03:39:26 +0000 (13:39 +1000)]
[POWERPC] Fix build break in arch/ppc/syslib/m8260_setup.c
Fix build break and warnings in current mainline git:
arch/ppc/syslib/m8260_setup.c: In function 'm8260_setup_arch':
arch/ppc/syslib/m8260_setup.c:63: error: implicit declaration of function 'identify_ppc_sys_by_name_and_id'
arch/ppc/syslib/m8260_setup.c:64: warning: passing argument 1 of 'in_be32' makes pointer from integer without a cast
arch/ppc/syslib/m8260_setup.c: In function 'm8260_show_cpuinfo':
arch/ppc/syslib/m8260_setup.c:158: warning: format '%08x' expects type 'unsigned int', but argument 5 has type 'long unsigned int'
arch/ppc/syslib/m8260_setup.c:158: warning: format '%d' expects type 'int', but argument 6 has type 'long unsigned int'
arch/ppc/syslib/m8260_setup.c:158: warning: format '%u' expects type 'unsigned int', but argument 7 has type 'long unsigned int'
arch/ppc/syslib/m8260_setup.c:158: warning: format '%u' expects type 'unsigned int', but argument 8 has type 'long unsigned int'
arch/ppc/syslib/m8260_setup.c:158: warning: format '%u' expects type 'unsigned int', but argument 9 has type 'long unsigned int'
make[1]: *** [arch/ppc/syslib/m8260_setup.o] Error 1
make[1]: *** Waiting for unfinished jobs....
Signed-off-by: Olof Johansson <olof@lixom.net> Signed-off-by: Paul Mackerras <paulus@samba.org>
Paul Mundt [Thu, 8 Nov 2007 02:24:33 +0000 (11:24 +0900)]
sh: Kill off broken snapgear ds1302 code.
This will force the snapgear boards to use the on-chip SH RTC instead,
until the rtc-ds1302 driver is merged. The current code is broken
and hasn't built in some time, so just kill it off and get the board
working again.
Stephen Smalley [Wed, 7 Nov 2007 15:08:00 +0000 (10:08 -0500)]
SELinux: add more validity checks on policy load
Add more validity checks at policy load time to reject malformed
policies and prevent subsequent out-of-range indexing when in permissive
mode. Resolves the NULL pointer dereference reported in
https://bugzilla.redhat.com/show_bug.cgi?id=357541.
Signed-off-by: Stephen Smalley <sds@tycho.nsa.gov> Signed-off-by: James Morris <jmorris@namei.org>
Jens Axboe [Wed, 7 Nov 2007 12:54:07 +0000 (13:54 +0100)]
ioprio: allow sys_ioprio_set() value of 0 to reset ioprio setting
Normally io priorities follow the CPU nice, unless a specific scheduling
class has been set. Once that is set, there's no way to reset the
behaviour to 'none' so that it follows CPU nice again.
Currently passing in 0 as the ioprio class/value will return -1/EINVAL,
change that to allow resetting of a set scheduling class.
Oleg Nesterov [Wed, 7 Nov 2007 12:51:35 +0000 (13:51 +0100)]
cfq_idle_class_timer: add paranoid checks for jiffies overflow
In theory, if the queue was idle long enough, cfq_idle_class_timer may have
a false (and very long) timeout because jiffies can wrap into the past wrt
->last_end_request.
Patrick McHardy [Wed, 7 Nov 2007 10:42:09 +0000 (02:42 -0800)]
[NETLINK]: Fix unicast timeouts
Commit ed6dcf4a in the history.git tree broke netlink_unicast timeouts
by moving the schedule_timeout() call to a new function that doesn't
propagate the remaining timeout back to the caller. This means on each
retry we start with the full timeout again.
ipc/mqueue.c seems to actually want to wait indefinitely so this
behaviour is retained.
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / linux-beck.git / log