Introduce a helper function to enable/disable a timer.
The disable of timers 0 and 1 in apci3120_interrupt() is probably not needed.
For now use the helper function to make sure the devpriv->ctrl bits are cleared
correctly to disable the timers.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com> Reviewed-by: Ian Abbott <abbotti@mev.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
staging: comedi: addi_apci_3120: tidy up devpriv->ctrl use
The apci3120_setup_chan_list() function sets devpriv->ctrl to the scan length
(PR) and scan start (PA) values and writes the value to the register. There is
no need to mask the value first.
The apci3120_ai_insn_read() function calles apci3120_setup_chan_list(). There
is no need to clear devpriv->ctrl first or clear any additional bits and write
the register again. This also fixes an incorrect use of APCI3120_DISABLE_TIMER0
to disable the timer.
apci3120_cyclic_ai() also calls apci3120_setup_chan_list() so it does not need
to clear devpriv->ctrl or clear any addidional bits and write the register.
Update the comments in apci3120_reset() and apci3120_cancel().
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com> Reviewed-by: Ian Abbott <abbotti@mev.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
staging: comedi: addi_apci_3120: fix counter and external interrupt disable
The APCI3120_DISABLE_ALL_TIMER define define is not needed, and it's used
incorrectly in apci3120_cancel(). The define is a mask of the bits needed
to disable the counters. Writing the value directly sets unintended bits.
Prior to writing the value, the 'devpriv->us_OutputRegister' is set to 0
and written to the register. This disables all the timers and the external
trigger.
Remove the unnecessary apci3120_exttrig_disable() call as well as the write
of APCI3120_DISABLE_ALL_TIMER.
In apci3120_interrupt(), remove the unnecessary mask and write to disable
all the timers. The COMEDI_CB_EOA event will cause the core to call the
(*cancel) operation which will disable the timers.
Remove the unused define.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com> Reviewed-by: Ian Abbott <abbotti@mev.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
staging: comedi: addi_apci_3120: tidy up CTR0 register defines
Define the CTR0 register in the main driver source file and remove all
the old defines in hwrdv_apci3120.c.
For aesthetics, save the raw digital output state (devpriv->do_bits) in
the digital output (*insn_bits) function and use a macro to set them when
reading/writing a timer.
Use the CTR0 register define in the digital output (*insn_bits) function
and remove the current register define.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com> Reviewed-by: Ian Abbott <abbotti@mev.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The timer divisor calculations in this driver are over complicated.
There are three timers on the board. They all use the same base clock
with a fixed prescaler for each timer. The base clock used depends on
the board version and type:
APCI-3120 Rev A boards OSC = 14.29MHz base clock (~70ns)
APCI-3120 Rev B boards OSC = 20MHz base clock (50ns)
APCI-3001 boards OSC = 20MHz base clock (50ns)
Daeseok Youn [Thu, 6 Nov 2014 10:27:59 +0000 (19:27 +0900)]
staging: dgap: introducing find_board_by_major()
use find_board_by_major function instead of getting a brd from static
arrary. Becasue tty's major number doesn't start zero and we can
find a brd from dgap_board[].
Daeseok Youn [Thu, 6 Nov 2014 10:27:33 +0000 (19:27 +0900)]
staging: dgap: remove useless variables for saving tty's major
The board_t has a tty_struct(serial_driver and print_driver)
that has a major number. When major number is compared in
dgap_tty_open(), just use brd->serial_driver{print_driver}->major.
Daeseok Youn [Thu, 6 Nov 2014 10:27:11 +0000 (19:27 +0900)]
staging: dgap: fix memory leak caused by double allocation of tty_structs
The tty_struct of serial_driver and print_driver were getting
allocated twice. One is allocated in tty_alloc_driver(), the other
is in dgap_tty_register(). So remove these in dgap_tty_register().
staging: comedi: amplc_pci230: use comedi_async 'scans_done' to detect AI EOA
Remove the private data member 'ai_scan_count' and use the comedi_async 'scans_done'
member to detect the analog input end-of-acquisition.
Use the comedi_nsamples_left() helper to work out the number of 'wake' samples in
pci230_ai_update_fifo_trigger_level() and the number of 'todo' samples actually
added to the async buffer in pci230_handle_ai().
Remove the unnecessary COMEDI_CB_OVERFLOW event for the hardware FIFO overflow
error. The COMEDI_CB_ERROR event will terminate the command.
comedi_buf_write_samples() can fail if the async buffer does not have room for
the sample. The it will set the COMEDI_CB_OVERFLOW event and return 0. Detect
this and quit trying to read and add more samples. The event will terminate the
command.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com> Reviewed-by: Ian Abbott <abbotti@mev.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ian Abbott [Fri, 31 Oct 2014 17:47:39 +0000 (17:47 +0000)]
staging: comedi: split out PCI support into new module
Setting the `CONFIG_COMEDI_PCI_DRIVERS` kernel configuration option
makes the main "comedi" module depend on the PCI support in the kernel.
That's not that big a deal since PCI support in the kernel is either
built into the kernel or is absent, and is not in a separate module.
Still, not all low-level Comedi drivers need PCI support, so we could
save a bit of space by not including it. The Comedi PCI support
functions are all in "comedi_pci.c". Turn it into a separate module so
the support code doesn't have to be loaded unnecessarily.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk> Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ian Abbott [Fri, 31 Oct 2014 17:47:38 +0000 (17:47 +0000)]
staging: comedi: split out USB support into new module
Setting the `CONFIG_COMEDI_USB_DRIVERS` kernel configuration option
makes the main "comedi" module depend on the "usbcore" module. But
perhaps the machine has no USB controllers (or they have been disabled),
in which case the "usbcore" module may have been pulled in
unnecessarily. Only a few low-level Comedi drivers require USB support.
The Comedi USB support functions are all in "comedi_usb.c". Turn it
into a separate module so we don't have to pull in the "usbcore" and
"usb_common" modules unnecessarily.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk> Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ian Abbott [Fri, 31 Oct 2014 17:47:37 +0000 (17:47 +0000)]
staging: comedi: split out PCMCIA support into new module
Setting the `CONFIG_COMEDI_PCMCIA_DRIVERS` kernel configuration option
makes the main "comedi" module depend on the "pcmcia" module, but many
machines don't have PCMCIA slots and only a few low-level Comedi drivers
need PCMCIA support. The Comedi PCMCIA support functions are all in
"comedi_pcmcia.c". Turn it into a separate module so we don't have to
pull in the other PCMCIA support modules unnecessarily.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk> Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ian Abbott [Fri, 31 Oct 2014 17:47:36 +0000 (17:47 +0000)]
staging: comedi: comedidev.h: remove some #ifdefs
Some declarations and macro definitions in "comedidev.h" are protected
by various `#ifdef`s for kernel configuration options, but the header
file compiles fine without the `#ifdef`s regardless of whether those
config option macros are defined or not. Remove the `#ifdef`s and
compile the affected code unconditionally.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk> Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ian Abbott [Fri, 31 Oct 2014 17:47:35 +0000 (17:47 +0000)]
staging: comedi: comedidev.h: remove dummy PCI support functions
Some low-level Comedi driver modules used to handle PCI devices and ISA
devices in the same module with some conditional compilation. To reduce
the amount of conditional compilation, some dummy inline versions of
`comedi_to_pci_dev()`, `comedi_pci_enable()`, `comedi_pci_disable()`,
and `comedi_pci_detach()` are defined in "comedidev.h" if
`CONFIG_COMEDI_PCI_DRIVERS` is undefined. Since those Comedi low-level
driver modules have since had PCI support split out into separate
modules, there is no need to keep the dummy inline functions around any
more, so remove them.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk> Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sudip Mukherjee [Fri, 7 Nov 2014 12:18:34 +0000 (17:48 +0530)]
staging: unisys: unneeded NULL check
the NULL check for memregion is not required as it has already been
checked for NULL after kzalloc. so we can reach this part of the code
only if memregion is not NULL.
staging: comedi: usbduxsigma: use comedi_async 'scans_done' to detect AI EOA
Remove the private data member 'ai_sample_count' and use the comedi_async
'scans_done' member to detect the analog input end-of-acquisition.
Move the EOA check so it happens after adding the samples from the current
urb to the async buffer. This prevents the unnecessary resubmit of the urb
when the EOA occurs.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com> Reviewed-by: Ian Abbott <abbotti@mev.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
staging: comedi: usbdux: use comedi_async 'scans_done' to detect AI EOA
Remove the private data member 'ai_sample_count' and use the comedi_async
'scans_done' member to detect the analog input end-of-acquisition.
Move the EOA check so it happens after adding the samples from the current
urb to the async buffer. This prevents the unnecessary resubmit of the urb
when the EOA occurs.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com> Reviewed-by: Ian Abbott <abbotti@mev.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
staging: comedi: comedidev.h: add 'scans_done' member to comedi_async
Introduce a new member to comedi_async to count the number of scans completed.
This member is cleared by comedi_buf_reset() along with the other comedi_async
members. It is incremented in comedi_inc_scan_progress() when the end of scan
is detected.
This member will be used to clean up the scan counting in the comedi drivers.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com> Reviewed-by: Ian Abbott <abbotti@mev.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ian Abbott [Tue, 4 Nov 2014 18:09:01 +0000 (18:09 +0000)]
staging: comedi: add ioctls to set per-file read and write subdevice
Now that Comedi has the structures in place to support setting the
current "read" and/or "write" subdevice on a per-file object basis, add
new ioctls to set them. The newly chosen "read" ("write") subdevice
needs to support "read" ("write") commands, and the file cannot be busy
handling a "read" ("write") command on the previous subdevice (if any).
Signed-off-by: Ian Abbott <abbotti@mev.co.uk> Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ian Abbott [Tue, 4 Nov 2014 18:09:00 +0000 (18:09 +0000)]
staging: comedi: prepare support for per-file read and write subdevices
Comedi devices may have several subdevices that support "read" and/or
"write" asynchronous commands that use the "read" or "write" file
operations for data transfer. The low-level Comedi drivers may nominate
a default "read" subdevice and/or a default "write" subdevice, but it
may have other subdevices that support asynchronous commands.
The Comedi core provides a somewhat clunky mechanism to provide access
to the asynchronous command support of the non-default subdevices. When
a low-level device is "attached" to a core Comedi device, it dynamically
allocates a minor device number for each of the subdevices that support
asynchrounous commands and associates them with files created in SysFS
named "comediX_subdY", where "X" is the minor device number of the main
comedi device, and "Y" is the subdevice number. An application can open
these subdevice-specific files and they behave like the regular
"comediX" files except that the "read" and/or "write" subdevice may be
different to the default chosen by the low-level driver.
This patch adds a layer of indirection between the file object and the
comedi device object to allow the current "read" and/or "write"
subdevice to be altered after opening the Comedi device, on a per-file
object basis. The advantage is that an application only needs to open
the main Comedi device file and can then choose which subdevice it wants
to "read" or "write". The main Comedi device file can be opened more
than once, and each file object can choose the "read" and "write"
subdevices independently.
The new `struct comedi_file` is created on "open" and freed on
"release". It includes pointers to the main Comedi device structure,
and to the current "read" and "write" subdevice structures (which may be
NULL). It also has information to keep track of when a low-level device
has been attached or detached since the previous time the file object
was used. In that case, the current "read" and "write" subdevices in
the `struct comedi_file` will be changed to the new defaults (or set to
NULL). (The change to new defaults is done by `comedi_file_reset()`.
The checking for attach/detach is done by `comedi_file_check()` which
will call `comedi_file_reset()` if there have been any attach/detach
operations since the previous call.)
A subsequent patch will add the ioctls to change the current "read" and
"write" subdevices.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk> Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Daeseok Youn [Wed, 5 Nov 2014 08:58:11 +0000 (17:58 +0900)]
staging: dgap: remove unnecessary function
The dgap_init_global() initialize the dgap_board
that is a global variable as static and dgap_poll_timer.
But init_timer() is called twice in dgap_start() and dgap_board
doesn't need to be initialized to NULL.
Ken Depro [Wed, 5 Nov 2014 15:57:57 +0000 (10:57 -0500)]
staging: unisys: Remove extra blank lines from virthba files
This patch removes extra blank lines from the virthba header and source
files. This is the first of a set of patches that will clean up the
virthba source file. The only checkpatch issue in the header file was
the blank line warnings.
Signed-off-by: Ken Depro <kenneth.depro@unisys.com> Signed-off-by: Ben Romer <benjamin.romer@unisys.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / karo-tx-linux.git / log