Rafa³ Bilski [Mon, 1 Jan 2007 22:49:34 +0000 (23:49 +0100)]
[CPUFREQ] Longhaul - Always guess FSB
This is patch that solves Ebox mini PC issue and make
FSB code more specification compilant. At start guess_fsb
function is guessing 200MHz FSB too. It is better to
make it in this way because, thanks to this function, driver
will fail for bogus FSB values caused by bogus multiplier
value. For PowerSaver processors we can't depend on Max /
MinMHzFSB because these values are only used for
PowerSaver 2.0 and 3.0. Most processors on which Longhaul
is used are PowerSaver 1.0 only. I'm changing code for older
CPU's too, but not so much as previously, and this code was
already used for Ezra. Using MinMHzBR for Ezra-T is outside
spec. It is for voltage scaling purpose and don't have to
be equal to minmult (but it is). Same for Nehemiah (it
isn't for sure). Added mult - current multiplier value.
Signed-off-by: Rafa³ Bilski <rafalbilski@interia.pl> Signed-off-by: Dave Jones <davej@redhat.com>
Rafa³ Bilski [Sun, 24 Dec 2006 13:04:23 +0000 (14:04 +0100)]
[CPUFREQ] Longhaul - Fix up powersaver assumptions.
ACPI PM2 register was fallback for "Longhaul ver. 1" CPU's.
My assumption that this register isn't present at
"PowerSaver" motherboards is so far true, but current code
will not work correctly in other case. There are three possible
supports: ACPI C3, PM2 and northbridge. That was my assumption
that ACPI C3 and northbridge is for PS and northbridge and PM2
is for V1. In current code we can only check if it is ACPI
support or not by port22_en. So remove port22_en and add
longhaul_flags. If USE_ACPI_C3 and USE_NORTHBRIDGE are both
clear then it means ACPI PM2 support. Also change order of
support probe from ACPI C3, PM2, northbridge to ACPI C3,
northbridge, ACPI PM2. Paranoid protection against port 0x22
cast as ACPI PM2 register. Bit 1 clear in such case - lockup
on AGP DMA. And obvious (now) fixup for do_powersaver. Use
cx->address only for ACPI C3 ("PowerSaver" processor using
PM2 support).
Signed-off-by: Rafa¿ Bilski <rafalbilski@interia.pl> Signed-off-by: Dave Jones <davej@redhat.com>
[CPUFREQ] Bug fix for acpi-cpufreq and cpufreq_stats oops on frequency change notification
Fixes the oops in cpufreq_stats with acpi_cpufreq driver. The issue was
that the frequency was reported as 0 in acpi-cpufreq.c. The bug is due to
different indicies for freq_table and ACPI perf table.
Also adds a check in cpufreq_stats to check for error return from
freq_table_get_index() and avoid using the error return value.
Patch fixes the issue reported at
http://www.ussg.iu.edu/hypermail/linux/kernel/0611.2/0629.html
and also other similar issue here
http://bugme.osdl.org/show_bug.cgi?id=7383 comment 53
Signed-off-by: Dhaval Giani <dhaval.giani@gmail.com> Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Dave Jones <davej@redhat.com>
Linus Torvalds [Wed, 13 Dec 2006 02:53:48 +0000 (18:53 -0800)]
Merge branch 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] kprobe clears qp bits for special instructions
[IA64] enable trap code on slot 1
[IA64] Take defensive stance on ia64_pal_get_brand_info()
[IA64] fix possible XPC deadlock when disconnecting
[IA64] - Reduce overhead of FP exception logging messages
[IA64] fix arch/ia64/mm/contig.c:235: warning: unused variable `nid'
[IA64] s/termios/ktermios/ in simserial.c
[IA64] kexec/kdump: tidy up declaration of relocate_new_kernel_t
[IA64] Kexec/Kdump: honour non-zero crashkernel offset.
[IA64] CONFIG_KEXEC/CONFIG_CRASH_DUMP permutations
[IA64] Do not call SN_SAL_SET_CPU_NUMBER twice on cpu 0
* master.kernel.org:/pub/scm/linux/kernel/git/davej/agpgart:
[AGPGART] VIA and SiS AGP chipsets are x86-only
[AGPGART] agp-amd64: section mismatches with HOTPLUG=n
[AGPGART] Fix up misprogrammed bridges with incorrect AGPv2 rates.
Linus Torvalds [Wed, 13 Dec 2006 02:52:31 +0000 (18:52 -0800)]
Merge branch 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband:
IPoIB: Make sure struct ipoib_neigh.queue is always initialized
IB/iser: Use the new verbs DMA mapping functions
IB/srp: Use new verbs IB DMA mapping functions
IPoIB: Use the new verbs DMA mapping functions
IB/core: Use the new verbs DMA mapping functions
IB/ipath: Implement new verbs DMA mapping functions
IB: Add DMA mapping functions to allow device drivers to interpose
RDMA/cma: Export rdma cm interface to userspace
RDMA/cma: Add support for RDMA_PS_UDP
RDMA/cma: Allow early transition to RTS to handle lost CM messages
RDMA/cma: Report connect info with connect events
RDMA/cma: Remove unneeded qp_type parameter from rdma_cm
IB/ipath: Fix IRQ for PCI Express HCAs
RDMA/amso1100: Fix memory leak in c2_qp_modify()
IB/iser: Remove unused "write-only" variables
IB/ipath: Remove unused "write-only" variables
IB/fmr: ib_flush_fmr_pool() may wait too long
* git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivial:
Fix inotify maintainers entry
Fix typo in new debug options.
Jon needs a new shift key.
fs: Convert kmalloc() + memset() to kzalloc() in fs/.
configfs.h: Remove dead macro definitions.
kconfig: Standardize "depends" -> "depends on" in Kconfig files
e100: replace kmalloc with kcalloc
um: replace kmalloc+memset with kzalloc
fix typo in net/ipv4/ip_fragment.c
include/linux/compiler.h: reject gcc 3 < gcc 3.2
Kconfig: fix spelling error in config KALLSYMS help text
Remove duplicate "have to" in comment
Fix small typo in drivers/serial/icom.c
Use consistent casing in help message
EXT{2,3,4}_FS: remove outdated part of the help text
Matthew Wilcox [Mon, 4 Dec 2006 10:43:14 +0000 (03:43 -0700)]
[AGPGART] VIA and SiS AGP chipsets are x86-only
There's no point in troubling the Alpha, IA-64, PowerPC and PARISC
people with SiS and VIA options. Andrew thinks it helps find bugs,
but there's no evidence of that.
Signed-off-by: Matthew Wilcox <matthew@wil.cx> Signed-off-by: Dave Jones <davej@redhat.com>
Randy Dunlap [Mon, 20 Nov 2006 02:52:28 +0000 (18:52 -0800)]
[AGPGART] agp-amd64: section mismatches with HOTPLUG=n
When CONFIG_HOTPLUG=n, agp_amd64_resume() calls nforce3_agp_init(),
which is __devinit == __init, so has been discarded and is not
usable for resume.
WARNING: drivers/char/agp/amd64-agp.o - Section mismatch: reference to .init.text: from .text between 'agp_amd64_resume' (at offset 0x249) and 'amd64_tlbflush'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Dave Jones <davej@redhat.com>
Roland Dreier [Tue, 12 Dec 2006 22:48:18 +0000 (14:48 -0800)]
IPoIB: Make sure struct ipoib_neigh.queue is always initialized
Move the initialization of ipoib_neigh's skb_queue into
ipoib_neigh_alloc(), since commit 2745b5b7 ("IPoIB: Fix skb leak when
freeing neighbour") will make iterate over the skb_queue to free any
packets left over when freeing the ipoib_neigh structure.
This fixes a crash when freeing ipoib_neigh structures allocated in
ipoib_mcast_send(), which otherwise don't have their skb_queue
initialized.
Wim Van Sebroeck [Tue, 12 Dec 2006 22:46:47 +0000 (23:46 +0100)]
[WATCHDOG] pcwd_usb.c generic HID include file
Now that the generic HID layer created include/linux/hid.h
we can use the HID_REQ_SET_REPORT and HID_DT_REPORT defines
directly from that include file.
Support for Core CPUs was broken in two ways in speedstep-lib: for x86_64,
we missed a MSR definition; for both x86_64 and i386, the FSB calculation
was wrong by four (it's a quad-pumped bus). Also increase the accuracy
of the calculation.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net> Signed-off-by: Dave Jones <davej@redhat.com>
Ralph Campbell [Tue, 12 Dec 2006 22:27:41 +0000 (14:27 -0800)]
IB: Add DMA mapping functions to allow device drivers to interpose
The QLogic InfiniPath HCAs use programmed I/O instead of HW DMA.
This patch allows a verbs device driver to interpose on DMA mapping
function calls in order to avoid relying on bus_to_virt() and
phys_to_virt() to undo the mappings created by dma_map_single(),
dma_map_sg(), etc.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
[CPUFREQ] Fix the bug in duplicate freq elimination code in acpi-cpufreq
Fix the bug in duplicate states elimination in acpi-cpufreq.
Bug: Due to duplicate state elimiation in the loop earlier, the number
of valid_states can be less than perf->state_count, in which case
freq_table was ending up with some garbage/uninitialized entries
in the table.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
From: Alexey Starikovskiy <alexey.y.starikovskiy@intel.com> Signed-off-by: Dave Jones <davej@redhat.com>
Gary Hade [Fri, 10 Nov 2006 19:20:47 +0000 (11:20 -0800)]
[CPUFREQ] speedstep-centrino should ignore upper performance control bits
On some systems there could be bits set in the upper half of
the control value provided by the _PSS object. These bits are
only relevant for cpufreq drivers that use IO ports which are not
currently supported by the speedstep-centrino driver. The current
MSR oriented code assumes that upper bits are not set and thus
fails to work correctly when they are. e.g. the control and status
value equality check failed on the IBM x3650 even though the ACPI
spec allows inequality.
Signed-off-by: Gary Hade <garyhade@us.ibm.com> Signed-off-by: Dave Jones <davej@redhat.com>
bibo,mao [Tue, 12 Dec 2006 20:04:42 +0000 (12:04 -0800)]
[IA64] kprobe clears qp bits for special instructions
On IA64 there exists some special instructions which
always need to be executed regradless of qp bits, such
as com.crel.unc, tbit.trel.unc etc.
This patch clears qp bits when inserting kprobe trap code
and disables probepoint on slot 1 for these special
instructions.
Signed-off-by: bibo,mao <bibo.mao@intel.com> Signed-off-by: Tony Luck <tony.luck@intel.com>
Tony Luck [Tue, 14 Nov 2006 17:33:38 +0000 (09:33 -0800)]
[IA64] enable trap code on slot 1
Because slot 1 of one instr bundle crosses border of two consecutive
8-bytes, kprobe on slot 1 is disabled. This patch enables kprobe on
slot1, it only replaces higher 8-bytes of the instruction bundle and
changes the exception code to ignore the low 12 bits of the break
number (which is across the border in the lower 8-bytes of the bundle).
For those instructions which must execute regardless qp bits,
kprobe on slot 1 is still disabled.
Signed-off-by: bibo,mao <bibo.mao@intel.com> Signed-off-by: Tony Luck <tony.luck@intel.com>
Tony Luck [Tue, 12 Dec 2006 19:56:36 +0000 (11:56 -0800)]
[IA64] Take defensive stance on ia64_pal_get_brand_info()
Stephane thought he saw a problem here (but was just confused
by the return value from ia64_pal_get_brand_info()). But we
should be more defensive here in case an prototype PAL for
a future processor doesn't implement this PAL call.
Sean Hefty [Fri, 1 Dec 2006 00:44:16 +0000 (16:44 -0800)]
RDMA/cma: Add support for RDMA_PS_UDP
Allow the use of UD QPs through the rdma_cm, in order to provide
address translation services for resolving IB addresses for datagram
messages using SIDR.
Signed-off-by: Sean Hefty <sean.hefty@intel.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
Sean Hefty [Fri, 1 Dec 2006 00:37:15 +0000 (16:37 -0800)]
RDMA/cma: Allow early transition to RTS to handle lost CM messages
During connection establishment, the passive side of a connection can
receive messages from the active side before the connection event has
been delivered to the user. Allow the passive side to send messages
in response to received data before the event is delivered. To handle
the case where the connection messages are lost, a new rdma_notify()
function is added that users may invoke to force a connection into the
established state.
Signed-off-by: Sean Hefty <sean.hefty@intel.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
Sean Hefty [Fri, 1 Dec 2006 00:33:14 +0000 (16:33 -0800)]
RDMA/cma: Report connect info with connect events
Connection information was never given to the recipient of a
connection request or reply message. Only the event was delivered.
Report the connection data with the event to allows user to
reject the connection based on the requested parameters, or adjust
their resources to match the request.
Signed-off-by: Sean Hefty <sean.hefty@intel.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
Roland Dreier [Tue, 12 Dec 2006 19:50:20 +0000 (11:50 -0800)]
IB/ipath: Fix IRQ for PCI Express HCAs
Commit 51f65ebc ("IB/ipath - program intconfig register using new HT
irq hook"), which fixed interrupts for HyperTransport HCAs, broke PCI
Express HCAs, because for those HCAs, the driver uses the value of
pdev->irq before pci_enable_msi() and ends up getting a totally bogus
IRQ number. Fix this by using the value of pdev->irq after
pci_enable_msi().
Roland Dreier [Tue, 12 Dec 2006 19:50:20 +0000 (11:50 -0800)]
IB/iser: Remove unused "write-only" variables
Remove variables that are set but then never looked at in the iSER
initiator. These cleanups came from David Binderman's list of "set
but never used" warnings from icc.
Roland Dreier [Tue, 12 Dec 2006 19:50:20 +0000 (11:50 -0800)]
IB/ipath: Remove unused "write-only" variables
Remove variables that are set but then never looked at in the ipath
driver. These cleanups came from David Binderman's list of "set but
never used" warnings from icc.
Roland Dreier [Tue, 12 Dec 2006 19:50:19 +0000 (11:50 -0800)]
IB/fmr: ib_flush_fmr_pool() may wait too long
ib_flush_fmr_pool() stashes away the request generation number
properly, but then goes ahead and rereads it every time it tests
whether the flush generation number has caught up. This means that
there is a theoretical possibility of livelock, if the request
generation number keeps getting bumped and the flush generation number
never catches up. The fix is simple: use the request generation
number read at the beginning of the function.
Also, atomic_inc() followed by atomic_read() can be replaced with
atomic_int_return(). There's no real requirement for atomicity here
but we might as well shrink the code.
This bug was discovered using David Binderman's list of "set but never
used" warnings from icc.
Dean Nelson [Wed, 22 Nov 2006 14:25:00 +0000 (08:25 -0600)]
[IA64] fix possible XPC deadlock when disconnecting
This patch eliminates a potential deadlock that is possible when XPC
disconnects a channel to a partition that has gone down. This deadlock will
occur if at least one of the kthreads created by XPC for the purpose of making
callouts to the channel's registerer is detained in the registerer and will
not be returning back to XPC until some registerer request occurs on the now
downed partition. The potential for a deadlock is removed by ensuring that
there always is a kthread available to make the channel disconnecting callout
to the registerer.
Signed-off-by: Dean Nelson <dcn@sgi.com> Signed-off-by: Tony Luck <tony.luck@intel.com>
Jack Steiner [Wed, 22 Nov 2006 15:55:08 +0000 (09:55 -0600)]
[IA64] - Reduce overhead of FP exception logging messages
Improve the scalability of the fpswa code that rate-limits
logging of messages.
There are 2 distinctly different problems in this code.
1) If prctl is used to disable logging, last_time is never
updated. The result is that fpu_swa_count is zeroed out on
EVERY fp fault. This causes a very very hot cache line.
The fix reduces the wallclock time of a 1024p FP exception test
from 28734 sec to 19 sec!!!
2) On VERY large systems, excessive messages are logged because
multiple cpus can each reset or increment fpu_swa_count at
about the same time. The result is that hundreds of messages
are logged each second. The fixes reduces the logging rate
to ~1 per second.
Signed-off-by: Jack Steiner <steiner@sgi.com> Signed-off-by: Tony Luck <tony.luck@intel.com>
This warning only shows up with CONFIG_VIRTUAL_MEM_MAP=y and
CONFIG_FLATMEM=y.
There is only one caller left for register_active_ranges() from the
contig.c code ... so it doesn't need to pick up the node number, the
node number is always zero.
Nicolas Pitre [Tue, 12 Dec 2006 18:32:29 +0000 (13:32 -0500)]
[PATCH] remove config ordering/dependency between ucb1400-ts and sound subsystem
Commit 2d4ba4a3b9aef95d328d74a17ae84f8d658059e2 introduced a dependency
that was never meant to exist when the ac97_bus.c module was created.
Move ac97_bus.c up the directory hierarchy to make sure it is built when
selected even if sound is configured out so things work as originally
intended.
Signed-off-by: Nicolas Pitre <nico@cam.org> Acked-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There seems to be a value in both allowing the kernel to determine
the base offset of the crashkernel automatically and allowing
users's to sepcify it.
The old behaviour on ia64, which is still the current behaviour on
most architectures is for the user to always specify the address.
Recently ia64 was changed so that it is always automatically determined.
With this patch the kernel automatically determines the offset if
the supplied value is 0, otherwise it uses the value provided.
This should probably be backed by a documentation change.
Signed-Off-By: Simon Horman <horms@verge.net.au> Signed-off-by: Tony Luck <tony.luck@intel.com>
Actually, on reflection I think that there is a good case for
keeping the options separate. I am thinking particularly of people
who want a very small crashdump kernel and thus don't want to compile
in kexec.
The patch below should fix things up so that all valid combinations of
KEXEC, CRASH_DUMP and VMCORE compile cleanly - VMCORE depends on
CRASH_DUMP which is why I said valid combinations. In a nutshell
it just untangles unrelated code and switches around a few defines.
Please note that it creats a new file, arch/ia64/kernel/crash_dump.c
This is in keeping with the i386 implementation.
Signed-off-by: Simon Horman <horms@verge.net.au> Signed-off-by: Tony Luck <tony.luck@intel.com>
Linus Torvalds [Tue, 12 Dec 2006 17:57:55 +0000 (09:57 -0800)]
Merge branch 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6
* 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
i2c: Fix OMAP clock prescaler to match the comment
i2c: Refactor a kfree in i2c-dev
i2c: Fix return value check in i2c-dev
i2c: Enable PEC on more i2c-i801 devices
i2c: Discard the i2c algo del_bus wrappers
i2c: New ARM Versatile/Realview bus driver
i2c: fix broken ds1337 initialization
i2c: i2c-i801 documentation update
i2c: Use the __ATTR macro where possible
i2c: Whitespace cleanups
i2c: Use put_user instead of copy_to_user where possible
i2c: New Atmel AT91 bus driver
i2c: Add support for nested i2c bus locking
i2c: Cleanups to the i2c-nforce2 bus driver
i2c: Add request/release_mem_region to i2c-ibm_iic bus driver
i2c: New Philips PNX bus driver
i2c: Delete the broken i2c-ite bus driver
i2c: Update the list of driver IDs
i2c: Fix documentation typos
Ingo Molnar [Tue, 12 Dec 2006 12:49:35 +0000 (13:49 +0100)]
[PATCH] net, 8139too.c: fix netpoll deadlock
fix deadlock in the 8139too driver: poll handlers should never forcibly
enable local interrupts, because they might be used by netpoll/printk
from IRQ context.
=================================
[ INFO: inconsistent lock state ]
2.6.19 #11
---------------------------------
inconsistent {softirq-on-W} -> {in-softirq-W} usage.
swapper/1 [HC0[0]:SC1[1]:HE1:SE0] takes:
(&npinfo->poll_lock){-+..}, at: [<c0350a41>] net_rx_action+0x64/0x1de
{softirq-on-W} state was registered at:
[<c0134c86>] mark_lock+0x5b/0x39c
[<c0135012>] mark_held_locks+0x4b/0x68
[<c01351e9>] trace_hardirqs_on+0x115/0x139
[<c02879e6>] rtl8139_poll+0x3d7/0x3f4
[<c035c85d>] netpoll_poll+0x82/0x32f
[<c035c775>] netpoll_send_skb+0xc9/0x12f
[<c035cdcc>] netpoll_send_udp+0x253/0x25b
[<c0288463>] write_msg+0x40/0x65
[<c011cead>] __call_console_drivers+0x45/0x51
[<c011cf16>] _call_console_drivers+0x5d/0x61
[<c011d4fb>] release_console_sem+0x11f/0x1d8
[<c011d7d7>] register_console+0x1ac/0x1b3
[<c02883f8>] init_netconsole+0x55/0x67
[<c010040c>] init+0x9a/0x24e
[<c01049cf>] kernel_thread_helper+0x7/0x10
[<ffffffff>] 0xffffffff
irq event stamp: 819992
hardirqs last enabled at (819992): [<c0350a16>] net_rx_action+0x39/0x1de
hardirqs last disabled at (819991): [<c0350b1e>] net_rx_action+0x141/0x1de
softirqs last enabled at (817552): [<c01214e4>] __do_softirq+0xa3/0xa8
softirqs last disabled at (819987): [<c0106051>] do_softirq+0x5b/0xc9
other info that might help us debug this:
no locks held by swapper/1.
Ingo Molnar [Tue, 12 Dec 2006 11:10:28 +0000 (12:10 +0100)]
[PATCH] lockdep: fix seqlock_init()
seqlock_init() needs to use spin_lock_init() for dynamic locks, so that
lockdep is notified about the presence of a new lock.
(this is a fallout of the recent networking merge, which started using
the so-far unused seqlock_init() API.)
This fix solves the following lockdep-internal warning on current -git:
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
__lock_acquire+0x10c/0x9f9
lock_acquire+0x56/0x72
_spin_lock+0x35/0x42
neigh_destroy+0x9d/0x12e
neigh_periodic_timer+0x10a/0x15c
run_timer_softirq+0x126/0x18e
__do_softirq+0x6b/0xe6
do_softirq+0x64/0xd2
ksoftirqd+0x82/0x138
Linus Torvalds [Tue, 12 Dec 2006 16:01:50 +0000 (08:01 -0800)]
Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/mchehab/v4l-dvb
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/mchehab/v4l-dvb:
V4L/DVB (4954): Fix: On ia64, i2c adap->inb/adap->outb are wrongly evaluated
V4L/DVB (4954): Fix: On ia64, i2c adap->inb/adap->outb are wrongly evaluated
i2c defines two callbacks (inb/outb). On ia64, since it defines also two macros
with those names, it causes the following errors:
drivers/media/video/usbvision/usbvision-i2c.c:64:39: macro "outb" passed 4 arguments, but takes just 2
drivers/media/video/usbvision/usbvision-i2c.c: In function `try_write_address':
drivers/media/video/usbvision/usbvision-i2c.c:64: warning: assignment makes integer from pointer without a cast
drivers/media/video/usbvision/usbvision-i2c.c:89:38: macro "inb" passed 4 arguments, but takes just 1
drivers/media/video/usbvision/usbvision-i2c.c: In function `try_read_address':
drivers/media/video/usbvision/usbvision-i2c.c:89: warning: assignment makes integer from pointer without a cast
drivers/media/video/usbvision/usbvision-i2c.c:85: warning: unused variable `buf'
drivers/media/video/usbvision/usbvision-i2c.c:173:53: macro "inb" passed 4 arguments, but takes just 1
drivers/media/video/usbvision/usbvision-i2c.c: In function `usb_xfer':
drivers/media/video/usbvision/usbvision-i2c.c:173: warning: assignment makes integer from pointer without a cast
drivers/media/video/usbvision/usbvision-i2c.c:179:54: macro "outb" passed 4 arguments, but takes just 2
drivers/media/video/usbvision/usbvision-i2c.c:179: warning: assignment makes integer from pointer without a cast
thanks to Andrew Morton for pointing this.
Boaz Harrosh [Tue, 5 Dec 2006 09:19:14 +0000 (10:19 +0100)]
[PATCH] remove blk_queue_activity_fn
While working on bidi support at struct request level
I have found that blk_queue_activity_fn is actually never used.
The only user is in ide-probe.c with this code:
/* enable led activity for disk drives only */
if (drive->media == ide_disk && hwif->led_act)
blk_queue_activity_fn(q, hwif->led_act, drive);
And led_act is never initialized anywhere.
(Looking back at older kernels it was used in the PPC arch, but was removed around 2.6.18)
Unless it is all for future use off course.
(this patch is against linux-2.6-block.git as off 2006/12/4)
Linus Torvalds [Tue, 12 Dec 2006 02:28:59 +0000 (18:28 -0800)]
Merge branch 'for-linus' of git://www.atmel.no/~hskinnemoen/linux/kernel/avr32
* 'for-linus' of git://www.atmel.no/~hskinnemoen/linux/kernel/avr32:
[AVR32] Add missing #include <linux/param.h> to delay.c
[AVR32] Pass dev parameter to dma_cache_sync()
[AVR32] Implement intc_get_pending()
[AVR32] Don't include <asm/delay.h>
[AVR32] Put the chip in "stop" mode when halting the system
[AVR32] Set flow handler for external interrupts
[AVR32] Remove unused file
[AVR32] Remove mii_phy_addr and eth_addr from eth_platform_data
[AVR32] Move ethernet tag parsing to board-specific code
[AVR32] Add macb1 platform_device
[AVR32] Portmux API update
* git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (36 commits)
[POWERPC] Generic BUG for powerpc
[PPC] Fix compile failure do to introduction of PHY_POLL
[POWERPC] Only export __mtdcr/__mfdcr if CONFIG_PPC_DCR is set
[POWERPC] Remove old dcr.S
[POWERPC] Fix SPU coredump code for max_fdset removal
[POWERPC] Fix irq routing on some 32-bit PowerMacs
[POWERPC] ps3: Add vuart support
[POWERPC] Support ibm,dynamic-reconfiguration-memory nodes
[POWERPC] dont allow pSeries_probe to succeed without initialising MMU
[POWERPC] micro optimise pSeries_probe
[POWERPC] Add SPURR SPR to sysfs
[POWERPC] Add DSCR SPR to sysfs
[POWERPC] Fix 440SPe CPU table entry
[POWERPC] Add support for FP emulation for the e300c2 core
[POWERPC] of_device_register: propagate device_create_file return code
[POWERPC] Fix mmap of PCI resource with hack for X
[POWERPC] iSeries: head_64.o needs to depend on lparmap.s
[POWERPC] cbe_thermal: Fix initialization of sysfs attribute_group
[POWERPC] Remove QE header files from lite5200.c
[POWERPC] of_platform_make_bus_id(): make `magic' int
...
Ralf Baechle [Mon, 11 Dec 2006 11:54:52 +0000 (11:54 +0000)]
[MIPS] Discard .exit.text and .exit.data at runtime.
While the recent cset 86384d544157db23879064cde36061cdcafc6794 did improve
things it didn't resolve all the problems. So bite the bullet and discard
.exit.text and .exit.data at runtime. Which of course sucks because it
bloats binaries with code that will never ever be used but it's the only
thing that will work reliable as demonstrated by the function sd_major() in
drivers/scsi/sd.c.
Gcc may compile sd_major() using a jump table which it will put into
.rodata. If it also inlines sd_major's function body into exit_sd() which
gcc > 3.4.x does. If CONFIG_BLK_DEV_SD has been set to y we would like ld
to discard exit_sd's code at link time. However sd_major happens to
contain a switch statement which gcc will compile using a jump table in
.rodata on the architectures I checked. So, when ld later discards
.exit.text only the jump table in .rodata with its stale references to
the discard .exit.text will be left which any no antique ld will honor
with a link error.
Andrew Morton [Tue, 12 Dec 2006 01:24:46 +0000 (17:24 -0800)]
[NETPOLL]: Fix local_bh_enable() warning.
During boot we get:
netconsole: device eth0 not up yet, forcing it
e1000: eth0: e1000_watchdog: NIC Link is Up 100 Mbps Full Duplex
WARNING (!__warned) at kernel/softirq.c:137 local_bh_enable()
Normally networking isn't invoked with interrupts turned off, but I
suppose we don't have a choice here. This is unique being a place where you
can get called with BH on, off, or IRQs off.
Given that this is only used for printk, the easiest solution is probably
just to disable local IRQs instead of BH.
Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / linux-beck.git / log