Ariel Elior [Sun, 6 May 2012 07:05:57 +0000 (07:05 +0000)]
bnx2x: bug fix when loading after SAN boot
This is a bug fix for an "interface fails to load" issue.
The issue occurs when bnx2x driver loads after UNDI driver was previously
loaded over the chip. In such a scenario the UNDI driver is loaded and operates
in the pre-boot kernel, within its own specific host memory address range.
When the pre-boot stage is complete, the real kernel is loaded, in a new and
distinct host memory address range. The transition from pre-boot stage to boot
is asynchronous from UNDI point of view.
A race condition occurs when UNDI driver triggers a DMAE transaction to valid
host addresses in the pre-boot stage, when control is diverted to the real
kernel. This results in access to illegal addresses by our HW as the addresses
which were valid in the preboot stage are no longer considered valid.
Specifically, the 'was_error' bit in the pci glue of our device is set. This
causes all following pci transactions from chip to host to timeout (in
accordance to the pci spec).
Signed-off-by: Ariel Elior <ariele@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Silence sparse warnings shown below:
...
drivers/net/ethernet/intel/e1000/e1000_main.c:3435:17: warning:
cast to restricted __le64
drivers/net/ethernet/intel/e1000/e1000_main.c:3435:17: warning:
cast to restricted __le64
...
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
John Fastabend [Mon, 23 Apr 2012 12:22:39 +0000 (12:22 +0000)]
igb, ixgbe: netdev_tx_reset_queue incorrectly called from tx init path
igb and ixgbe incorrectly call netdev_tx_reset_queue() from
i{gb|xgbe}_clean_tx_ring() this sort of works in most cases except
when the number of real tx queues changes. When the number of real
tx queues changes netdev_tx_reset_queue() only gets called on the
new number of queues so when we reduce the number of queues we risk
triggering the watchdog timer and repeated device resets.
So this is not only a cosmetic issue but causes real bugs. For
example enabling/disabling DCB or FCoE in ixgbe will trigger this.
CC: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Tested-by: John Bishop <johnx.bishop@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Matthew Garrett [Thu, 3 May 2012 20:50:46 +0000 (16:50 -0400)]
efivars: Improve variable validation
Ben Hutchings pointed out that the validation in efivars was inadequate -
most obviously, an entry with size 0 would server as a DoS against the
kernel. Improve this based on his suggestions.
Signed-off-by: Matthew Garrett <mjg@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 4 May 2012 00:16:52 +0000 (17:16 -0700)]
Merge tag 'tag/upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
Pull libata fixes from Jeff Garzik:
1) Fix regression that could cause a misdiagnosis, which in turn could
lead to an erroneous 3.0 Gbps -> 1.5 downshift, particularly when hotplug
and suspend/resume is involved.
2) Fix a regression that led to ata%d controller ids being numbered one
larger than in <= 3.4-rc3 (oh, the horror!). Controller ids should now be
as expected.
3) add some DT, PCI id's
4) ata/pata_arasan_cf: minor cpp fixing/cleaning
* tag 'tag/upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
ata: ahci_platform: Add synopsys ahci controller in DT's compatible list
ata/pata_arasan_cf: Move arasan_cf_pm_ops out of #ifdef, #endif macros
libata: init ata_print_id to 0
ahci: Detect Marvell 88SE9172 SATA controller
libata: skip old error history when counting probe trials
Linus Torvalds [Fri, 4 May 2012 00:15:47 +0000 (17:15 -0700)]
Merge branch 'i2c-embedded/for-current' of git://git.pengutronix.de/git/wsa/linux
Pull i2c embedded fixes from Wolfram Sang:
"Here are some typical i2c driver bugfixes for 3.4. Missed clock
handling, improper timeout fixes, hardware wrokarounds... All
patches have been in linux-next for a few days, too."
* 'i2c-embedded/for-current' of git://git.pengutronix.de/git/wsa/linux:
i2c: mxs: disable QUEUE when sending is done
i2c: mxs: handle spurious interrupt
i2c-eg20t: Modify MODULE_AUTHOR's email address
i2c-eg20t: change timeout value 50msec to 1000msec
i2c: tegra: Add delay before resetting the controller after NACK
i2c: pnx: Disable clk in suspend
Linus Torvalds [Fri, 4 May 2012 00:14:55 +0000 (17:14 -0700)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Just some regression fixes from Ben along with a variable that gcc
failed to spot is uninitialised."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
nouveau: initialise has_optimus variable.
drm/nv10/gpio: fix thinko in mask for gpio lines 2-9
nvc0/fb: shut up PMFB interrupt after the first occurrence
drm/nouveau/hdmi: use correct hdmi regs for nvaa/nvac
drm/nouveau/bios: fix regression on some nv4x board
1) Transfer padding was wrong for full-speed USB in ASIX driver, fix
from Ingo van Lil.
2) Propagate the negative packet offset fix into the PowerPC BPF JIT.
From Jan Seiffert.
3) dl2k driver's private ioctls were letting unprivileged tasks make
MII writes and other ugly bits like that. Fix from Jeff Mahoney.
4) Fix TX VLAN and RX packet drops in ucc_geth, from Joakim Tjernlund.
5) OOPS and network namespace fixes in IPVS from Hans Schillstrom and
Julian Anastasov.
6) Fix races and sleeping in locked context bugs in drop_monitor, from
Neil Horman.
7) Fix link status indication in smsc95xx driver, from Paolo Pisati.
8) Fix bridge netfilter OOPS, from Peter Huang.
9) L2TP sendmsg can return on error conditions with the socket lock
held, oops. Fix from Sasha Levin.
10) udp_diag should return meaningful values for socket memory usage,
from Shan Wei.
11) Eric Dumazet is so awesome he gets his own section:
Socket memory cgroup code (I never should have applied those
patches, grumble...) made erroneous changes to
sk_sockets_allocated_read_positive(). It was changed to
use percpu_counter_sum_positive (which requires BH disabling)
instead of percpu_counter_read_positive (which does not).
Revert back to avoid crashes and lockdep warnings.
Adjust the default tcp_adv_win_scale and tcp_rmem[2] values
to fix throughput regressions. This is necessary as a result
of our more precise skb->truesize tracking.
Fix SKB leak in netem packet scheduler.
12) New device IDs for various bluetooth devices, from Manoj Iyer,
AceLan Kao, and Steven Harms.
13) Fix command completion race in ipw2200, from Stanislav Yakovlev.
14) Fix rtlwifi oops on unload, from Larry Finger.
15) Fix hard_mtu when adjusting hard_header_len in smsc95xx driver.
From Stephane Fillod.
16) ehea driver registers it's IRQ before all the necessary state is
setup, resulting in crashes. Fix from Thadeu Lima de Souza
Cascardo.
17) Fix PHY connection failures in davinci_emac driver, from Anatolij
Gustschin.
18) Missing break; in switch statement in bluetooth's
hci_cmd_complete_evt(). Fix from Szymon Janc.
19) Fix queue programming in iwlwifi, from Johannes Berg.
20) Interrupt throttling defaults not being actually programmed into the
hardware, fix from Jeff Kirsher and Ying Cai.
21) TLAN driver SKB encoding in descriptor busted on 64-bit, fix from
Benjamin Poirier.
22) Fix blind status block RX producer pointer deref in TG3 driver, from
Matt Carlson.
23) Promisc and multicast are busted on ehea, fixes from Thadeu Lima de
Souza Cascardo.
24) Fix crashes in 6lowpan, from Alexander Smirnov.
25) tcp_complete_cwr() needs to be careful to not rewind the CWND to
ssthresh if ssthresh has the "infinite" value. Fix from Yuchung
Cheng.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (81 commits)
sungem: Fix WakeOnLan
tcp: change tcp_adv_win_scale and tcp_rmem[2]
net: l2tp: unlock socket lock before returning from l2tp_ip_sendmsg
drop_monitor: prevent init path from scheduling on the wrong cpu
usbnet: fix failure handling in usbnet_probe
usbnet: fix leak of transfer buffer of dev->interrupt
ucc_geth: Add 16 bytes to max TX frame for VLANs
net: ucc_geth, increase no. of HW RX descriptors
netem: fix possible skb leak
sky2: fix receive length error in mixed non-VLAN/VLAN traffic
sky2: propogate rx hash when packet is copied
net: fix two typos in skbuff.h
cxgb3: Don't call cxgb_vlan_mode until q locks are initialized
ixgbe: fix calling skb_put on nonlinear skb assertion bug
ixgbe: Fix a memory leak in IEEE DCB
igbvf: fix the bug when initializing the igbvf
smsc75xx: enable mac to detect speed/duplex from phy
smsc75xx: declare smsc75xx's MII as GMII capable
smsc75xx: fix phy interrupt acknowledge
smsc75xx: fix phy init reset loop
...
Linus Torvalds [Fri, 4 May 2012 00:08:58 +0000 (17:08 -0700)]
Merge tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
"Fix OOPS seen in coretemp driver if the CPU core ID is too large"
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (coretemp) Increase CPU core limit
hwmon: (coretemp) fix oops on cpu unplug
When comparing the dmesg between 3.4-rc3 and 3.4-rc4 I found the
following differences:
-ata1: SATA max UDMA/133 abar m2048@0xf9fff000 port 0xf9fff100 irq 47
-ata2: SATA max UDMA/133 abar m2048@0xf9fff000 port 0xf9fff180 irq 47
-ata3: DUMMY
+ata2: SATA max UDMA/133 abar m2048@0xf9fff000 port 0xf9fff100 irq 47
+ata3: SATA max UDMA/133 abar m2048@0xf9fff000 port 0xf9fff180 irq 47
ata4: DUMMY
ata5: DUMMY
-ata6: SATA max UDMA/133 abar m2048@0xf9fff000 port 0xf9fff380 irq 47
+ata6: DUMMY
+ata7: SATA max UDMA/133 abar m2048@0xf9fff000 port 0xf9fff380 irq 47
The change of numbering comes from commit 85d6725b7c0d7e3f ("libata:
make ata_print_id atomic") that changed lines like
ap->print_id = ata_print_id++;
to
ap->print_id = atomic_inc_return(&ata_print_id);
As the latter behaves like ++ata_print_id, we must initialize
it to zero to start the numbering from one.
Signed-off-by: Tero Roponen <tero.roponen@gmail.com> Acked-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Lin Ming [Thu, 3 May 2012 14:15:07 +0000 (22:15 +0800)]
libata: skip old error history when counting probe trials
Commit d902747("[libata] Add ATA transport class") introduced
ATA_EFLAG_OLD_ER to mark entries in the error ring as cleared.
But ata_count_probe_trials_cb() didn't check this flag and it still
counts the old error history. So wrong probe trials count is returned
and it causes problem, for example, SATA link speed is slowed down from
3.0Gbps to 1.5Gbps.
Fix it by checking ATA_EFLAG_OLD_ER in ata_count_probe_trials_cb().
Cc: stable <stable@vger.kernel.org> # 2.6.37+ Signed-off-by: Lin Ming <ming.m.lin@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Eric Dumazet [Sat, 24 Mar 2012 04:29:46 +0000 (00:29 -0400)]
iwlwifi: fix skb truesize underestimation
By default, iwlwifi uses order-1 pages (8 KB) to store incoming frames,
but doesnt say so in skb->truesize.
This makes very possible to exhaust kernel memory since these skb evade
normal socket memory accounting.
As struct ieee80211_hdr is going to be pulled before calling IP stack,
there is no need to use dev_alloc_skb() to reserve NET_SKB_PAD bytes.
alloc_skb() is ok in this driver, allowing more tailroom.
Pull beginning of frame in skb header, in the hope we can reuse order-1
pages in the driver immediately for small frames and reduce their
truesize to the minimum (linear skbs)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Cc: Wey-Yi Guy <wey-yi.w.guy@intel.com> Cc: "John W. Linville" <linville@tuxdriver.com> Cc: Neal Cardwell <ncardwell@google.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
The BIT_APP_UPCHG bit is no longer set when ixgbe_dcbnl_set_all() is
called. This results in the FCoE app user priority never getting set
and the driver will not configure the tx_rings correctly for FCoE
packets which use the SAN MTU and FCoE offloads.
We resolve this regression by fixing ixgbe_copy_dcb_cfg() to also
check for FCoE application changes. Additionally, we can drop the
IEEE variants of get_dcb_app() because this path is never called
with the IEEE mode enabled.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Tested-by: Ross Brattain <ross.b.brattain@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Don Skidmore [Sat, 17 Mar 2012 05:51:52 +0000 (05:51 +0000)]
ixgbe: fix race condition with shutdown
It was possible for shutdown to pull the rug out from other driver entry
points. Now we just grab the rtnl lock before taking everything apart.
Thanks to Hariharan for noticing this tight race condition.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com> Cc: Hariharan Nagarajan <hanagara@cisco.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
WakeOnLan was broken in this driver because gp->asleep_wol is a 1-bit
bitfield and it was being assigned WAKE_MAGIC, which is (1 << 5).
gp->asleep_wol remains 0 and the machine never wakes up. Fixed by casting
gp->wake_on_lan to bool. Tested on an iBook G4.
Signed-off-by: Gerard Lledo <gerard.lledo@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 2 May 2012 02:28:41 +0000 (02:28 +0000)]
tcp: change tcp_adv_win_scale and tcp_rmem[2]
tcp_adv_win_scale default value is 2, meaning we expect a good citizen
skb to have skb->len / skb->truesize ratio of 75% (3/4)
In 2.6 kernels we (mis)accounted for typical MSS=1460 frame :
1536 + 64 + 256 = 1856 'estimated truesize', and 1856 * 3/4 = 1392.
So these skbs were considered as not bloated.
With recent truesize fixes, a typical MSS=1460 frame truesize is now the
more precise :
2048 + 256 = 2304. But 2304 * 3/4 = 1728.
So these skb are not good citizen anymore, because 1460 < 1728
(GRO can escape this problem because it build skbs with a too low
truesize.)
This also means tcp advertises a too optimistic window for a given
allocated rcvspace : When receiving frames, sk_rmem_alloc can hit
sk_rcvbuf limit and we call tcp_prune_queue()/tcp_collapse() too often,
especially when application is slow to drain its receive queue or in
case of losses (netperf is fast, scp is slow). This is a major latency
source.
We should adjust the len/truesize ratio to 50% instead of 75%
This patch :
1) changes tcp_adv_win_scale default to 1 instead of 2
2) increase tcp_rmem[2] limit from 4MB to 6MB to take into account
better truesize tracking and to allow autotuning tcp receive window to
reach same value than before. Note that same amount of kernel memory is
consumed compared to 2.6 kernels.
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Neal Cardwell <ncardwell@google.com> Cc: Tom Herbert <therbert@google.com> Cc: Yuchung Cheng <ycheng@google.com> Acked-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sasha Levin [Wed, 2 May 2012 03:58:43 +0000 (03:58 +0000)]
net: l2tp: unlock socket lock before returning from l2tp_ip_sendmsg
l2tp_ip_sendmsg could return without releasing socket lock, making it all the
way to userspace, and generating the following warning:
[ 130.891594] ================================================
[ 130.894569] [ BUG: lock held when returning to user space! ]
[ 130.897257] 3.4.0-rc5-next-20120501-sasha #104 Tainted: G W
[ 130.900336] ------------------------------------------------
[ 130.902996] trinity/8384 is leaving the kernel with locks still held!
[ 130.906106] 1 lock held by trinity/8384:
[ 130.907924] #0: (sk_lock-AF_INET){+.+.+.}, at: [<ffffffff82b9503f>] l2tp_ip_sendmsg+0x2f/0x550
Introduced by commit 2f16270 ("l2tp: Fix locking in l2tp_ip.c").
Signed-off-by: Sasha Levin <levinsasha928@gmail.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Neil Horman [Tue, 1 May 2012 08:18:02 +0000 (08:18 +0000)]
drop_monitor: prevent init path from scheduling on the wrong cpu
I just noticed after some recent updates, that the init path for the drop
monitor protocol has a minor error. drop monitor maintains a per cpu structure,
that gets initalized from a single cpu. Normally this is fine, as the protocol
isn't in use yet, but I recently made a change that causes a failed skb
allocation to reschedule itself . Given the current code, the implication is
that this workqueue reschedule will take place on the wrong cpu. If drop
monitor is used early during the boot process, its possible that two cpus will
access a single per-cpu structure in parallel, possibly leading to data
corruption.
This patch fixes the situation, by storing the cpu number that a given instance
of this per-cpu data should be accessed from. In the case of a need for a
reschedule, the cpu stored in the struct is assigned the rescheule, rather than
the currently executing cpu
Tested successfully by myself.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com> CC: David Miller <davem@davemloft.net> Signed-off-by: David S. Miller <davem@davemloft.net>
usbnet: fix leak of transfer buffer of dev->interrupt
The transfer buffer of dev->interrupt is allocated in .probe path,
but not freed in .disconnet path, so mark the interrupt URB as
URB_FREE_BUFFER to free the buffer when the URB is destroyed.
Signed-off-by: Ming Lei <tom.leiming@gmail.com> Acked-by: Oliver Neukum <oneukum@suse.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Creating a VLAN interface on top of ucc_geth adds 4 bytes
to the frame and the HW controller is not prepared to
TX a frame bigger than 1518 bytes which is 4 bytes too
small for a full VLAN frame. Add 16 bytes which will handle
the a simple VLAN and leaves 12 bytes for future expansion.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Wed, 2 May 2012 20:48:33 +0000 (13:48 -0700)]
Merge tag 'usb-3.4-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB patches from Greg Kroah-Hartman:
"Here are two EHCI Tegra driver patches for your tree.
The first is a bit big, but the majority is just moving code around.
It is needed due to the other EHCI core changes that went in way back
in 3.4-rc1, so this driver will now properly handle suspend/resume, as
it was broken. The other one is a minor bugfix that resolves an
warning that people have been seeing."
* tag 'usb-3.4-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: ehci-tegra: remove redundant gpio_set_value
EHCI: update PM methods in ehci-tegra.c
Linus Torvalds [Wed, 2 May 2012 20:47:49 +0000 (13:47 -0700)]
Merge tag 'tty-3.4-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull a TTY fix from Greg Kroah-Hartman:
"This is a deadlock bugfix that was easy to hit, and that the vt layer
lock rework got wrong, so it reverts the logic back to the way it was
in 3.3 and earlier kernels to prevent problems."
* tag 'tty-3.4-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
vt: Fix deadlock on scroll-lock
Revert "ath9k_hw: Fix incorrect spur_freq_sd for AR9003"
This reverts commit a844adfd7bee4edc66d337de6c33b348e83552a8.
The commit a844adfd is degrading rx sensitivity of lower rate in
HT40 mode and it is confirmed that reverting the change is
improving rx sensitivity.
spur_freq_sd (for self-corr in AGC) is defined with respect to the
center of each 20MHz channel while spur_phase_delta (for self-corr
in Rx and spur data filter) is defined with respect to the center
of current RF channel.
So in short, we need to subtract spur_freq_sd (for self-corr in AGC)
by the offset between the center of primary20 and the center of RF
channel in SW. This offset could be +/10 MHz for dynamic 40.
Cc: Madhan Jaganathan <madhanj@qca.qualcomm.com> Signed-off-by: Kai Shi <kaishi@qca.qualcomm.com> Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Franky Lin [Mon, 30 Apr 2012 18:43:07 +0000 (11:43 -0700)]
brcmfmac: fix a double spin_unlock_irqrestore issue in dpc
dpc_tl_lock is not acquired in the error handle code for bus down.
But it's unlocked using spin_unlock_irqrestore after finishing task
list walk down. Grab the lock before breaking the loop to avoid a
double unlock.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Franky Lin <frankyl@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Linus Torvalds [Wed, 2 May 2012 15:17:57 +0000 (08:17 -0700)]
Merge tag 'nfs-for-3.4-4' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client bugfixes from Trond Myklebust:
- Fixes for the NFSv4 security negotiation
- Use the correct hostname when mounting from a private namespace
- NFS net namespace bugfixes for the pipefs filesystem
- NFSv4 GETACL bugfixes
- IPv6 bugfix for NFSv4 referrals
* tag 'nfs-for-3.4-4' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
NFSv4.1: Use the correct hostname in the client identifier string
SUNRPC: RPC client must use the current utsname hostname string
NFS: get module in idmap PipeFS notifier callback
NFS: Remove unused function nfs_lookup_with_sec()
NFS: Honor the authflavor set in the clone mount data
NFS: Fix following referral mount points with different security
NFS: Do secinfo as part of lookup
NFS: Handle exceptions coming out of nfs4_proc_fs_locations()
NFS: Fix SECINFO_NO_NAME
SUNRPC: traverse clients tree on PipeFS event
SUNRPC: set per-net PipeFS superblock before notification
SUNRPC: skip clients with program without PipeFS entries
SUNRPC: skip dead but not buried clients on PipeFS events
Avoid beyond bounds copy while caching ACL
Avoid reading past buffer when calling GETACL
fix page number calculation bug for block layout decode buffer
NFSv4.1 fix page number calculation bug for filelayout decode buffers
pnfs-obj: Remove unused variable from objlayout_get_deviceinfo()
nfs4: fix referrals on mounts that use IPv6 addrs
Linus Torvalds [Wed, 2 May 2012 02:43:34 +0000 (19:43 -0700)]
Merge tag 'ktest-for-v3.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-ktest
Pull two bug fixes in ktest from Steven Rostedt.
* tag 'ktest-for-v3.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-ktest:
ktest: Fix reboot on success stopping all reboots
ktest.pl: Fix combined usage of BISECT_REVERSE and BISECT_SKIP
Linus Torvalds [Wed, 2 May 2012 00:24:05 +0000 (17:24 -0700)]
Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Pull MIPS fixes from Ralf Baechle:
"misc fixes some of which are also applicable to 3.3 and removal of an
unused function. This has been sitting in -next for ages with no
complaints. Also there are no known regressions due to these patches"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: Remove get_current_pgd().
MIPS: ath79: fix AR933X WMAC reset code
MIPS: JZ4740: Fix the JZ4740_IRQ_DMA macro
MIPS: Use set_current_blocked() and block_sigmask()
Stephen Warren [Mon, 30 Apr 2012 23:24:10 +0000 (17:24 -0600)]
USB: ehci-tegra: remove redundant gpio_set_value
The immediately preceding gpio_direction_output() already set the value,
so there's no need to repeat it. This also prevents gpio_set_value() from
WARNing when the GPIO is sleepable (e.g. is on an I2C expander); the set
direction API is always sleepable, but plain set_value isn't.
Alan Stern [Tue, 1 May 2012 15:28:49 +0000 (11:28 -0400)]
EHCI: update PM methods in ehci-tegra.c
This patch (as1547) rearranges the Power Management parts of the
ehci-tegra driver to match the conventions used in other EHCI platform
drivers. In particular, the controller should not be powered down by
the root hub's suspend routine; the controller's power level should be
managed by the controller's own PM methods.
The end result of the patch is that the standard ehci_bus_suspend()
and ehci_bus_resume() methods can be used instead of special-purpose
routines. The driver now uses the standard dev_pm_ops methods instead
of legacy power management. Since there is no supported wakeup
mechanism for the controller, runtime suspend is forbidden by default
(this can be overridden via sysfs, if desired).
These adjustments are needed in order to make ehci-tegra compatible
with recent changes to the USB core. The core now checks the root
hub's status following bus suspend; if the controller is automatically
powered down during bus suspend then the check will fail and the root
hub will be resumed immediately. Doing the controller power-down in a
separate method avoids this problem.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Acked-by: Stephen Warren <swarren@wwwdotorg.org> Tested-by: Stephen Warren <swarren@wwwdotorg.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alan Cox [Tue, 1 May 2012 15:12:19 +0000 (16:12 +0100)]
vt: Fix deadlock on scroll-lock
Fixing the locking accidentally replaced a race in the scroll
lock handling with a deadlock. Turn it back into a race for
now.
The basic problem is that there are two paths into the tty
stop/start helpers. One via the tty layer ^S/^Q handling
where we need to take the kbd_event_lock and one via the
special keyboard handler for fn_hold where we already hold
it. Probably we need to split out into a separate LED lock
but for now just go back to the race as it's a bit close
to release.
Reported-by: Clemens Ladisch <clemens@ladisch.de> Cc: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eric Dumazet [Sun, 29 Apr 2012 09:08:22 +0000 (09:08 +0000)]
netem: fix possible skb leak
skb_checksum_help(skb) can return an error, we must free skb in this
case. qdisc_drop(skb, sch) can also be feeded with a NULL skb (if
skb_unshare() failed), so lets use this generic helper.
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Stephen Hemminger <shemminger@osdl.org> Signed-off-by: David S. Miller <davem@davemloft.net>
sky2: fix receive length error in mixed non-VLAN/VLAN traffic
Bug: The VLAN bit of the MAC RX Status Word is unreliable in several older
supported chips. Sometimes the VLAN bit is not set for valid VLAN packets
and also sometimes the VLAN bit is set for non-VLAN packets that came after
a VLAN packet. This results in a receive length error when VLAN hardware
tagging is enabled.
Fix: Variation on original fix proposed by Mirko.
The VLAN information is decoded in the status loop, and can be
applied to the received SKB there. This eliminates the need for the
separate tag field in the interface data structure. The tag has to
be copied and cleared if packet is copied. This version checked out
with vlan and normal traffic.
Note: vlan_tx_tag_present should be renamed vlan_tag_present, but that
is outside scope of this.
Reported-by: Mirko Lindner <mlindner@marvell.com> Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
When a small packet is received, the driver copies it to a new skb to allow
reusing the full size Rx buffer. The copy was propogating the checksum offload
but not the receive hash information. The bug is impact was mostly harmless
and therefore not observed until reviewing this area of code.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Guenter Roeck [Tue, 1 May 2012 15:15:42 +0000 (08:15 -0700)]
hwmon: (coretemp) Increase CPU core limit
CPU core ID is used to index the core_data[] array. The core ID is, however, not
sequential; 10-core CPUS can have a core ID as high as 25. Increase the limit to
32 to be able to deal with current CPUs.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com> Cc: stable@vger.kernel.org # 3.0+ Acked-by: Jean Delvare <khali@linux-fr.org> Acked-by: Durgadoss R <durgadoss.r@intel.com>
Steven Rostedt [Tue, 1 May 2012 12:20:12 +0000 (08:20 -0400)]
ktest: Fix reboot on success stopping all reboots
The change to let individual tests decide to reboot the machine on
success of the entire test also prevented errors from rebooting
when an error was detected.
The "no_reboot" variable was only cleared if the test had
reboot_on_success set. But the no_reboot variable also prevents the test
rebooting when an error was detected even when REBOOT_ON_ERROR was set.
Add a new "reboot_success" variable that is used to determine if the
test should reboot on success and not touch the no_reboot variable.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
ktest.pl: Fix combined usage of BISECT_REVERSE and BISECT_SKIP
When BISECT_REVERSE and BISECT_SKIP are used together with boot or test
testing, build failures are treated as boot or test failures and
'git bisect bad' is executed instead of 'git bisect skip'. This is because
the $ret value of -1 is treated as a build failure, but the $reverse_bisect
logic does not properly handle this.
Dave Airlie [Tue, 1 May 2012 11:25:06 +0000 (12:25 +0100)]
Merge branch 'drm-nouveau-fixes' of git://git.freedesktop.org/git/nouveau/linux-2.6 into drm-fixes
* 'drm-nouveau-fixes' of git://git.freedesktop.org/git/nouveau/linux-2.6:
drm/nv10/gpio: fix thinko in mask for gpio lines 2-9
nvc0/fb: shut up PMFB interrupt after the first occurrence
drm/nouveau/hdmi: use correct hdmi regs for nvaa/nvac
drm/nouveau/bios: fix regression on some nv4x board
'ARM: OMAP3: USB: Fix the EHCI ULPI PHY reset issue' removes the include for
linux/gpio.h from omap-usb-host.c. This include indirectly includes plat/cpu.h
which is required by omap-usb-host.c. Fix the build breakage by including
it directly.
Acked-by: Keshava Munegowda <keshava_mgowda@ti.com> Acked-by: Kevin Hilman <khilman@ti.com> Tested-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Russ Dill <Russ.Dill@ti.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Roland Dreier [Mon, 30 Apr 2012 07:15:47 +0000 (07:15 +0000)]
cxgb3: Don't call cxgb_vlan_mode until q locks are initialized
The driver calls cxgb_vlan_mode() from init_one(). This calls into
synchronize_rx(), which locks all the q locks, but the q locks are not
initialized until cxgb_up() -> setup_sge_qsets(). So move the call to
cxgb_vlan_mode() into cxgb_up(), after the call to setup_sge_qsets().
We also move the body of these functions up higher to avoid having to
a forward declaration.
This was found because of the lockdep warning:
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
Pid: 323, comm: work_for_cpu Not tainted 3.4.0-rc5 #28
Call Trace:
[<ffffffff8106e767>] register_lock_class+0x108/0x2d0
[<ffffffff8106ff42>] __lock_acquire+0xd3/0xd06
[<ffffffff81070fd0>] lock_acquire+0xbf/0xfe
[<ffffffff813862a6>] _raw_spin_lock_irq+0x36/0x45
[<ffffffffa01e71aa>] cxgb_vlan_mode+0x96/0xcb [cxgb3]
[<ffffffffa01f90eb>] init_one+0x8c4/0x980 [cxgb3]
[<ffffffff811fcbf0>] local_pci_probe+0x3f/0x70
[<ffffffff81042206>] do_work_for_cpu+0x10/0x22
[<ffffffff810482de>] kthread+0xa1/0xa9
[<ffffffff8138e234>] kernel_thread_helper+0x4/0x10
Contrary to what lockdep says, the code is not fine: we are locking an
uninitialized spinlock.
Signed-off-by: Roland Dreier <roland@purestorage.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yi Zou [Fri, 20 Apr 2012 05:48:08 +0000 (05:48 +0000)]
ixgbe: fix calling skb_put on nonlinear skb assertion bug
With the support to bounce buffer added, the skb is coming as nonlinear in the
case of non-DDPed data frames for FCoE, which is mostly ok as the FCoE stack
would take care of that. However, for target mode, we have to set the FC CRC
and FC EOF field to allow the protocol stack to not drop the frame for the last
data frame of that sequence. So fix this by linearizing the skb first before
doing skb_put().
Signed-off-by: Yi Zou <yi.zou@intel.com> Tested-by: Marcus Dennis <marcusx.e.dennis@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Sat, 17 Mar 2012 02:39:16 +0000 (02:39 +0000)]
ixgbe: Fix a memory leak in IEEE DCB
The driver was freeing memory in shutdown instead of remove. As a result
we were leaking memory if IEEE DCB was enabled and we loaded/unloaded the
driver. This change moves the freeing of the memory into the remove
routine where it belongs.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Acked-by: John Fastabend <john.r.fastabend@intel.com> Tested-by: Ross Brattain <ross.b.brattain@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Samuel Liao [Fri, 27 Apr 2012 17:09:27 +0000 (17:09 +0000)]
igbvf: fix the bug when initializing the igbvf
Maybe it's a typo, but it cause that igbvf can't be initialized successfully.
Set perm_addr value using valid dev_addr, although which is equal to hw.mac.addr.
Signed-off-by: Samuel Liao <samuelliao@tencent.com> Signed-off-by: Shan Wei <davidshan@tencent.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
smsc75xx: enable mac to detect speed/duplex from phy
This patch sets the automatic speed and duplex detection bits
in MAC_CR to enable the mac to determine its speed automatically
from the phy.
Note this must be done BEFORE the receiver or transmitter is
enabled.
Signed-off-by: Stephane Fillod <fillods@users.sf.net> Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net> Signed-off-by: David S. Miller <davem@davemloft.net>
also explicitly set the phy to advertise 1000 speeds
Signed-off-by: Stephane Fillod <fillods@users.sf.net> Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net> Signed-off-by: David S. Miller <davem@davemloft.net>
smsc75xx phy interrupt acknowledge needs an mdio_write to clear
PHY_INT_SRC instead of just a read like in smsc95xx.
Signed-off-by: Stephane Fillod <fillods@users.sf.net> Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Stephane Fillod <fillods@users.sf.net> Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net> Signed-off-by: David S. Miller <davem@davemloft.net>
smsc75xx: add more information to register io failure warnings
Signed-off-by: Stephane Fillod <fillods@users.sf.net> Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net> Signed-off-by: David S. Miller <davem@davemloft.net>
smsc75xx needs MII_ACCESS_BUSY to be set to correctly trigger mdio I/O. Note smsc75xx is different from smsc95xx in this regard.
Signed-off-by: Stephane Fillod <fillods@users.sf.net> Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Merge branch 'fixes' of git://git.linaro.org/people/rmk/linux-arm
Pull ARM fixes from Russell King.
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7406/1: hotplug: copy the affinity mask when forcefully migrating IRQs
ARM: 7405/1: kexec: call platform_cpu_kill on the killer rather than the victim
ARM: 7403/1: tls: remove covert channel via TPIDRURW
ARM: 7401/1: mm: Fix section mismatches
ARM: OMAP: fix DMA vs memory ordering
ARM: 7390/1: dts: versatile-pb/ab fix MMC IRQs
ARM: 7400/1: vfp: clear fpscr length and stride bits on entry to sig handler
ARM: 7399/1: vfp: move user vfp state save/restore code out of signal.c
ARM: 7398/1: l2x0: only write to debug registers on PL310
ARM: 7397/1: l2x0: only apply workaround for erratum #753970 on PL310
ARM: 7396/1: errata: only handle ARM erratum #326103 on affected cores
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a set of SAS and SATA fixes; there are one or two longstanding
bug fixes, but most of this is regression fixes."
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
[SCSI] libfc: update mfs boundry checking
[SCSI] Revert "[SCSI] libsas: fix sas port naming"
[SCSI] libsas: fix false positive 'device attached' conditions
[SCSI] libsas, libata: fix start of life for a sas ata_port
[SCSI] libsas: fix ata_eh clobbering ex_phys via smp_ata_check_ready
[SCSI] libsas: unify domain_device sas_rphy lifetimes
[SCSI] libsas: fix sas_get_port_device regression
[SCSI] libsas: fix sas_find_bcast_phy() in the presence of 'vacant' phys
[SCSI] libsas: introduce sas_work to fix sas_drain_work vs sas_queue_work
[SCSI] libata: Pass correct DMA device to scsi host
[SCSI] scsi_lib: use correct DMA device in __scsi_alloc_queue
Matthew Garrett [Mon, 30 Apr 2012 20:11:30 +0000 (16:11 -0400)]
efi: Validate UEFI boot variables
A common flaw in UEFI systems is a refusal to POST triggered by a malformed
boot variable. Once in this state, machines may only be restored by
reflashing their firmware with an external hardware device. While this is
obviously a firmware bug, the serious nature of the outcome suggests that
operating systems should filter their variable writes in order to prevent
a malicious user from rendering the machine unusable.
Signed-off-by: Matthew Garrett <mjg@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Randy Dunlap [Mon, 30 Apr 2012 19:25:31 +0000 (12:25 -0700)]
nfsd: fix nfs4recover.c printk format warning
Fix printk format warnings -- both items are size_t,
so use %zu to print them.
fs/nfsd/nfs4recover.c:580:3: warning: format '%lu' expects type 'long unsigned int', but argument 3 has type 'size_t'
fs/nfsd/nfs4recover.c:580:3: warning: format '%lu' expects type 'long unsigned int', but argument 4 has type 'unsigned int'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net> Cc: "J. Bruce Fields" <bfields@fieldses.org> Cc: linux-nfs@vger.kernel.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Felix Fietkau [Sun, 29 Apr 2012 13:44:16 +0000 (15:44 +0200)]
mac80211: fix AP mode EAP tx for VLAN stations
EAP frames for stations in an AP VLAN are sent on the main AP interface
to avoid race conditions wrt. moving stations.
For that to work properly, sta_info_get_bss must be used instead of
sta_info_get when sending EAP packets.
Previously this was only done for cooked monitor injected packets, so
this patch adds a check for tx->skb->protocol to the same place.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Cc: stable@vger.kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
Merge branch 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
Pull powerpc fixes from Benjamin Herrenschmidt:
"Here are a handful more fixes for powerpc. The irq stuff are all
regression fixes, and Gavin's patch is a simple compile fix."
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
tty/serial/pmac_zilog: Fix "nobody cared" IRQ message
powerpc/pseries: Rivet CONFIG_EEH for pSeries platform
powerpc/irqdomain: Fix broken NR_IRQ references
powerpc/8xx: Fix NR_IRQ bugs and refactor 8xx interrupt controller
When the cwnd reduction is done, ssthresh may be infinite
if TCP enters CWR via ECN or F-RTO. If cwnd is not undone, i.e.,
undo_marker is set, tcp_complete_cwr() falsely set cwnd to the
infinite ssthresh value. The correct operation is to keep cwnd
intact because it has been updated in ECN or F-RTO.
Signed-off-by: Yuchung Cheng <ycheng@google.com> Acked-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jan Seiffert [Sun, 29 Apr 2012 19:02:19 +0000 (19:02 +0000)]
bpf jit: Let the powerpc jit handle negative offsets
Now the helper function from filter.c for negative offsets is exported,
it can be used it in the jit to handle negative offsets.
First modify the asm load helper functions to handle:
- know positive offsets
- know negative offsets
- any offset
then the compiler can be modified to explicitly use these helper
when appropriate.
This fixes the case of a negative X register and allows to lift
the restriction that bpf programs with negative offsets can't
be jited.
Tested-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Jan Seiffert <kaffeemonster@googlemail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bug is that sk_sockets_allocated_read_positive() calls
percpu_counter_sum_positive() without BH being disabled.
This bug was added in commit 180d8cd942ce33
(foundations of per-cgroup memory pressure controlling.), since previous
code was using percpu_counter_read_positive() which is IRQ safe.
In __sk_mem_schedule() we dont need the precise count of allocated
sockets and can revert to previous behavior.
Reported-by: Denys Fedoryshchenko <denys@visp.net.lb> Sined-off-by: Eric Dumazet <edumazet@google.com> Cc: Glauber Costa <glommer@parallels.com> Acked-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
SUNRPC: RPC client must use the current utsname hostname string
Now that the rpc client is namespace aware, it needs to use the
utsname of the process that created it instead of using the
init_utsname. Both rpc_new_client and rpc_clone_client need to
be fixed.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com> Cc: Stanislav Kinsbursky <skinsbursky@parallels.com>
Ben Skeggs [Fri, 13 Apr 2012 09:22:30 +0000 (19:22 +1000)]
drm/nouveau/bios: fix regression on some nv4x board
We started using the connector table on nv4x a while back, and this VBIOS
has bad connector indices which causes the wrong encoders to get paired
with connectors.
powerpc/pseries: Rivet CONFIG_EEH for pSeries platform
Recently, Ryan Wang tried to compile PPC pSeries platform without
CONFIG_EEH and eventually run into errors. Nishanth Aravamudan
helped to narrow down the root cause. Actually, the pSeries platform
depends on CONFIG_EEH heavily and that won't work properly without
EEH support.
According to Ben's suggestion, the patch make CONFIG_EEH invisible
and keep it as always selected on pSeries platform.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Grant Likely [Mon, 23 Apr 2012 12:30:02 +0000 (12:30 +0000)]
powerpc/irqdomain: Fix broken NR_IRQ references
The switch from using irq_map to irq_alloc_desc*() for managing irq
number allocations introduced new bugs in some of the powerpc
interrupt code. Several functions rely on the value of NR_IRQS to
determine the maximum irq number that could get allocated. However,
with sparse_irq and using irq_alloc_desc*() the maximum possible irq
number is now specified with 'nr_irqs' which may be a number larger
than NR_IRQS. This has caused breakage on powermac when
CONFIG_NR_IRQS is set to 32.
This patch removes most of the direct references to NR_IRQS in the
powerpc code and replaces them with either a nr_irqs reference or by
using the common for_each_irq_desc() macro. The powerpc-specific
for_each_irq() macro is removed at the same time.
Also, the Cell axon_msi driver is refactored to remove the global
build assumption on the size of NR_IRQS and instead add a limit to the
maximum irq number when calling irq_domain_add_nomap().
Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Grant Likely [Mon, 23 Apr 2012 12:30:01 +0000 (12:30 +0000)]
powerpc/8xx: Fix NR_IRQ bugs and refactor 8xx interrupt controller
The mpc8xx driver uses a reference to NR_IRQS that is buggy. It uses
NR_IRQs for the array size of the ppc_cached_irq_mask bitmap, but
NR_IRQs could be smaller than the number of hardware irqs that
ppc_cached_irq_mask tracks.
Also, while fixing that problem, it became apparent that the interrupt
controller only supports 32 interrupt numbers, but it is written as if
it supports multiple register banks which is more complicated.
This patch pulls out the buggy reference to NR_IRQs and fixes the size
of the ppc_cached_irq_mask to match the number of HW irqs. It also
drops the now-unnecessary code since ppc_cached_irq_mask is no longer
an array.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Merge tag 'pm-for-3.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael J. Wysocki:
"Fix for an issue causing hibernation to hang on systems with highmem
(that practically means i386) due to broken memory management (bug
introduced in 3.2, so -stable material) and PM documentation update
making the freezer documentation follow the code again after some
recent updates."
* tag 'pm-for-3.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM / Freezer / Docs: Update documentation about freezing of tasks
PM / Hibernate: fix the number of pages used for hibernate/thaw buffering
autofs: make the autofsv5 packet file descriptor use a packetized pipe
The autofs packet size has had a very unfortunate size problem on x86:
because the alignment of 'u64' differs in 32-bit and 64-bit modes, and
because the packet data was not 8-byte aligned, the size of the autofsv5
packet structure differed between 32-bit and 64-bit modes despite
looking otherwise identical (300 vs 304 bytes respectively).
We first fixed that up by making the 64-bit compat mode know about this
problem in commit a32744d4abae ("autofs: work around unhappy compat
problem on x86-64"), and that made a 32-bit 'systemd' work happily on a
64-bit kernel because everything then worked the same way as on a 32-bit
kernel.
But it turned out that 'automount' had actually known and worked around
this problem in user space, so fixing the kernel to do the proper 32-bit
compatibility handling actually *broke* 32-bit automount on a 64-bit
kernel, because it knew that the packet sizes were wrong and expected
those incorrect sizes.
As a result, we ended up reverting that compatibility mode fix, and
thus breaking systemd again, in commit fcbf94b9dedd.
With both automount and systemd doing a single read() system call, and
verifying that they get *exactly* the size they expect but using
different sizes, it seemed that fixing one of them inevitably seemed to
break the other. At one point, a patch I seriously considered applying
from Michael Tokarev did a "strcmp()" to see if it was automount that
was doing the operation. Ugly, ugly.
However, a prettier solution exists now thanks to the packetized pipe
mode. By marking the communication pipe as being packetized (by simply
setting the O_DIRECT flag), we can always just write the bigger packet
size, and if user-space does a smaller read, it will just get that
partial end result and the extra alignment padding will simply be thrown
away.
This makes both automount and systemd happy, since they now get the size
they asked for, and the kernel side of autofs simply no longer needs to
care - it could pad out the packet arbitrarily.
Of course, if there is some *other* user of autofs (please, please,
please tell me it ain't so - and we haven't heard of any) that tries to
read the packets with multiple writes, that other user will now be
broken - the whole point of the packetized mode is that one system call
gets exactly one packet, and you cannot read a packet in pieces.
Tested-by: Michael Tokarev <mjt@tls.msk.ru> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Cc: David Miller <davem@davemloft.net> Cc: Ian Kent <raven@themaw.net> Cc: Thomas Meyer <thomas@m3y3r.de> Cc: stable@kernel.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
PM / Freezer / Docs: Update documentation about freezing of tasks
The file Documentation/power/freezing-of-tasks.txt was still referencing
the TIF_FREEZE flag, that was removed by the commit d88e4cb67197d007fb778d62fe17360e970d5bfa(freezer: remove now unused
TIF_FREEZE).
This patch removes all the references of TIF_FREEZE that were left
behind.
Signed-off-by: Marcos Paulo de Souza <marcos.souza.org@gmail.com> Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The actual internal pipe implementation is already really about
individual packets (called "pipe buffers"), and this simply exposes that
as a special packetized mode.
When we are in the packetized mode (marked by O_DIRECT as suggested by
Alan Cox), a write() on a pipe will not merge the new data with previous
writes, so each write will get a pipe buffer of its own. The pipe
buffer is then marked with the PIPE_BUF_FLAG_PACKET flag, which in turn
will tell the reader side to break the read at that boundary (and throw
away any partial packet contents that do not fit in the read buffer).
End result: as long as you do writes less than PIPE_BUF in size (so that
the pipe doesn't have to split them up), you can now treat the pipe as a
packet interface, where each read() system call will read one packet at
a time. You can just use a sufficiently big read buffer (PIPE_BUF is
sufficient, since bigger than that doesn't guarantee atomicity anyway),
and the return value of the read() will naturally give you the size of
the packet.
NOTE! We do not support zero-sized packets, and zero-sized reads and
writes to a pipe continue to be no-ops. Also note that big packets will
currently be split at write time, but that the size at which that
happens is not really specified (except that it's bigger than PIPE_BUF).
Currently that limit is the system page size, but we might want to
explicitly support bigger packets some day.
The main user for this is going to be the autofs packet interface,
allowing us to stop having to care so deeply about exact packet sizes
(which have had bugs with 32/64-bit compatibility modes). But user
space can create packetized pipes with "pipe2(fd, O_DIRECT)", which will
fail with an EINVAL on kernels that do not support this interface.
Tested-by: Michael Tokarev <mjt@tls.msk.ru> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Cc: David Miller <davem@davemloft.net> Cc: Ian Kent <raven@themaw.net> Cc: Thomas Meyer <thomas@m3y3r.de> Cc: stable@kernel.org # needed for systemd/autofs interaction fix Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge tag 'staging-3.4-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging tree fixes from Greg Kroah-Hartman:
"Here are some tiny drivers/staging/ bugfixes. Some build fixes that
were recently reported, as well as one kfree bug that is hitting a
number of users."
* tag 'staging-3.4-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: ozwpan: Fix bug where kfree is called twice.
staging: octeon-ethernet: fix build errors by including interrupt.h
staging: zcache: fix Kconfig crypto dependency
staging: tidspbridge: remove usage of OMAP2_L4_IO_ADDRESS
Merge tag 'usb-3.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg Kroah-Hartman:
"Here are a number of small USB fixes for 3.4-rc5.
Nothing major, as before, some USB gadget fixes. There's a crash fix
for a number of ASUS laptops on resume that had been reported by a
number of different people. We think the fix might also pertain to
other machines, as this was a BIOS bug, and they seem to travel to
different models and manufacturers quite easily. Other than that,
some other reported problems fixed as well."
* tag 'usb-3.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: gadget: udc-core: fix incompatibility with dummy-hcd
usb: gadget: udc-core: fix wrong call order
USB: cdc-wdm: fix race leading leading to memory corruption
USB: EHCI: fix crash during suspend on ASUS computers
usb gadget: uvc: uvc_request_data::length field must be signed
usb: gadget: dummy: do not call pullup() on udc_stop()
usb: musb: davinci.c: add missing unregister
usb: musb: drop __deprecated flag
USB: gadget: storage gadgets send wrong error code for unknown commands
usb: otg: gpio_vbus: Add otg transceiver events and notifiers
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"This has our collection of bug fixes. I missed the last rc because I
thought our patches were making NFS crash during my xfs test runs.
Turns out it was an NFS client bug fixed by someone else while I tried
to bisect it.
All of these fixes are small, but some are fairly high impact. The
biggest are fixes for our mount -o remount handling, a deadlock due to
GFP_KERNEL allocations in readdir, and a RAID10 error handling bug.
This was tested against both 3.3 and Linus' master as of this morning."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs: (26 commits)
Btrfs: reduce lock contention during extent insertion
Btrfs: avoid deadlocks from GFP_KERNEL allocations during btrfs_real_readdir
Btrfs: Fix space checking during fs resize
Btrfs: fix block_rsv and space_info lock ordering
Btrfs: Prevent root_list corruption
Btrfs: fix repair code for RAID10
Btrfs: do not start delalloc inodes during sync
Btrfs: fix that check_int_data mount option was ignored
Btrfs: don't count CRC or header errors twice while scrubbing
Btrfs: fix btrfs_ioctl_dev_info() crash on missing device
btrfs: don't return EINTR
Btrfs: double unlock bug in error handling
Btrfs: always store the mirror we read the eb from
fs/btrfs/volumes.c: add missing free_fs_devices
btrfs: fix early abort in 'remount'
Btrfs: fix max chunk size check in chunk allocator
Btrfs: add missing read locks in backref.c
Btrfs: don't call free_extent_buffer twice in iterate_irefs
Btrfs: Make free_ipath() deal gracefully with NULL pointers
Btrfs: avoid possible use-after-free in clear_extent_bit()
...
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Nothing controversial, just another batch of fixes:
- Samsung/exynos fixes for more merge window fallout: build errors
and warnings mostly, but also some clock/device setup issues on
exynos4/5
- PXA bug and warning fixes related to gpio and pinmux
- IRQ domain conversion bugfixes for U300 and MSM
- A regulator setup fix for U300"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: PXA2xx: MFP: fix potential direction bug
ARM: PXA2xx: MFP: fix bug with MFP_LPM_KEEP_OUTPUT
arm/sa1100: fix sa1100-rtc memory resource
ARM: pxa: fix gpio wakeup setting
ARM: SAMSUNG: add missing MMC_CAP2_BROKEN_VOLTAGE capability
ARM: EXYNOS: Fix compilation error when CONFIG_OF is not defined
ARM: EXYNOS: Fix resource on dev-dwmci.c
ARM: S3C24XX: Fix build warning for S3C2410_PM
ARM: mini2440_defconfig: Fix build error
ARM: msm: Fix gic irqdomain support
ARM: EXYNOS: Fix incorrect initialization of GIC
ARM: EXYNOS: use 'exynos4-sdhci' as device name for sdhci controllers
ARM: u300: bump all IRQ numbers by one
ARM: ux300: Fix unimplementable regulation constraints
projects / linux-beck.git / log