The 'allclean' flag is used to cache the fact that there is nothing to
do, so we can avoid waking up and scanning the bitmap regularly.
The two sorts of pages that might need the attention of the bitmap
daemon are BITMAP_PAGE_PENDING and BITMAP_PAGE_NEEDWRITE pages.
So make sure allclean reflects exactly when there are none of those.
So:
set it before scanning all pages with either bit set.
clear it whenever these bits are set
clear it when we desire not to clear one of these bits.
don't clear it any other time.
The flag 'BITMAP_PAGE_CLEAN' has a confusing name as it doesn't mean
that the page is clean, but rather that there are counters in the page
which allow bits in the bitmap to be cleared - i.e. maybe cleaning can
happen.
So change it to BITMAP_PAGE_PENDING and fix some irregularities:
- Don't set it in bitmap_init_from_disk as bitmap_set_memory_bits
sets it when needed
- in bitmap_daemon_work, if we find a counter that is '1', but
need_sync is set, then set BITMAP_PAGE_PENDING again (it was
recently cleared) to ensure we don't forget about this bit.
md: Avoid waking up a thread after it has been freed.
Two related problems:
1/ some error paths call "md_unregister_thread(mddev->thread)"
without subsequently clearing ->thread. A subsequent call
to mddev_unlock will try to wake the thread, and crash.
2/ Most calls to md_wakeup_thread are protected against the thread
disappeared either by:
- holding the ->mutex
- having an active request, so something else must be keeping
the array active.
However mddev_unlock calls md_wakeup_thread after dropping the
mutex and without any certainty of an active request, so the
->thread could theoretically disappear.
So we need a spinlock to provide some protections.
So change md_unregister_thread to take a pointer to the thread
pointer, and ensure that it always does the required locking, and
clears the pointer properly.
md: Fix handling for devices from 2TB to 4TB in 0.90 metadata.
0.90 metadata uses an unsigned 32bit number to count the number of
kilobytes used from each device.
This should allow up to 4TB per device.
However we multiply this by 2 (to get sectors) before casting to a
larger type, so sizes above 2TB get truncated.
Also we allow rdev->sectors to be larger than 4TB, so it is possible
for the array to be resized larger than the metadata can handle.
So make sure rdev->sectors never exceeds 4TB when 0.90 metadata is in
used.
Also the sanity check at the end of super_90_load should include level
1 as it used ->size too. (RAID0 and Linear don't use ->size at all).
A write can complete at two different places:
1/ when the last member-device write completes, through
raid10_end_write_request
2/ in make_request() when we remove the initial bias from ->remaining.
These two should do exactly the same thing and the comment says they
do, but they don't.
So factor the correct code out into a function and call it in both
places. This makes the code much more similar to RAID1.
The difference is only significant if there is an error, and they
usually take a while, so it is unlikely that there will be an error
already when make_request is completing, so this is unlikely to cause
real problems.
Avoid dereferencing a 'request_queue' after last close.
On the last close of an 'md' device which as been stopped, the device
is destroyed and in particular the request_queue is freed. The free
is done in a separate thread so it might happen a short time later.
__blkdev_put calls bdev_inode_switch_bdi *after* ->release has been
called.
Since commit f758eeabeb96f878c860e8f110f94ec8820822a9
bdev_inode_switch_bdi will dereference the 'old' bdi, which lives
inside a request_queue, to get a spin lock. This causes the last
close on an md device to sometime take a spin_lock which lives in
freed memory - which results in an oops.
So move the called to bdev_inode_switch_bdi before the call to
->release.
NeilBrown [Wed, 31 Aug 2011 02:49:14 +0000 (12:49 +1000)]
md/raid5: fix a hang on device failure.
Waiting for a 'blocked' rdev to become unblocked in the raid5d thread
cannot work with internal metadata as it is the raid5d thread which
will clear the blocked flag.
This wasn't a problem in 3.0 and earlier as we only set the blocked
flag when external metadata was used then.
However we now set it always, so we need to be more careful.
NeilBrown [Tue, 30 Aug 2011 06:20:17 +0000 (16:20 +1000)]
md: fix clearing of 'blocked' flag in the presence of bad blocks.
When the 'blocked' flag on a device is cleared while there are
unacknowledged bad blocks we must fail the device. This is needed for
backwards compatability of the interface.
The code currently uses the wrong test for "unacknowledged bad blocks
exist". Change it to the right test.
NeilBrown [Thu, 25 Aug 2011 04:43:53 +0000 (14:43 +1000)]
md/linear: avoid corrupting structure while waiting for rcu_free to complete.
I don't know what I was thinking putting 'rcu' after a dynamically
sized array! The array could still be in use when we call rcu_free()
(That is the point) so we mustn't corrupt it.
Namhyung Kim [Thu, 25 Aug 2011 04:43:34 +0000 (14:43 +1000)]
md: use REQ_NOIDLE flag in md_super_write()
Queue idling is used for the anticipation of immediate
sequencial I/O's but md_super_write() is a kind of one-
shot operation, coupled with md_super_wait(), so the
idling in this case will be just a waste of time.
Specifying REQ_NOIDLE prevents it. Instead of adding
the flag to submit_bio() directly, use pre-defined
macro WRITE_FLUSH_FUA.
Signed-off-by: Namhyung Kim <namhyung@gmail.com> Signed-off-by: NeilBrown <neilb@suse.de>
Linus Torvalds [Wed, 24 Aug 2011 01:09:08 +0000 (18:09 -0700)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86-32, vdso: On system call restart after SYSENTER, use int $0x80
x86, UV: Remove UV delay in starting slave cpus
x86, olpc: Wait for last byte of EC command to be accepted
H. Peter Anvin [Mon, 22 Aug 2011 20:27:06 +0000 (13:27 -0700)]
x86-32, vdso: On system call restart after SYSENTER, use int $0x80
When we enter a 32-bit system call via SYSENTER or SYSCALL, we shuffle
the arguments to match the int $0x80 calling convention. This was
probably a design mistake, but it's what it is now. This causes
errors if the system call as to be restarted.
For SYSENTER, we have to invoke the instruction from the vdso as the
return address is hardcoded. Accordingly, we can simply replace the
jump in the vdso with an int $0x80 instruction and use the slower
entry point for a post-restart.
Linus Torvalds [Tue, 23 Aug 2011 18:41:44 +0000 (11:41 -0700)]
Merge branch 'for-linus' of git://oss.sgi.com/xfs/xfs
* 'for-linus' of git://oss.sgi.com/xfs/xfs:
xfs: fix tracing builds inside the source tree
xfs: remove subdirectories
xfs: don't expect xfs headers to be in subdirectories
Linus Torvalds [Tue, 23 Aug 2011 17:46:21 +0000 (10:46 -0700)]
Merge branch 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon: Extended DDC Probing for Toshiba L300D Radeon Mobility X1100 HDMI-A Connector
drm/ttm: ensure ttm for new node is bound before calling move_notify()
drm/ttm: unbind ttm before destroying node in accel move cleanup
drm/ttm: fix ttm_bo_add_ttm(user) failure path
drm/radeon: Make vramlimit parameter actually work.
drm/radeon: Explicitly print GTT/VRAM offsets on test failure.
drm/radeon: Take IH ring into account for test size calculation.
drm/radeon/alpha: Add Alpha support to Radeon DRM code
It turns out that this breaks several drivers, one example being OMAP
boards which use the on-board OMAP UARTs and the omap-serial driver that
will not boot to userspace after the commit.
Paul Walmsley reports that enabling CONFIG_DEBUG_SHIRQ reveals 'IRQ
handler type mismatch' errors:
IRQ handler type mismatch for IRQ 74
current handler: serial idle
...
and the reason is that setting IRQF_ONESHOT will now result in those
interrupt handlers having different IRQF flags, and thus being
unsharable. So the commit log in the reverted commit:
"Since it is required for those users and
there is no difference for others it makes sense to add this flag
unconditionally."
is simply not true: there may not be any difference from a "actions at
irq time", but there is a *big* difference wrt this flag testing irq
management (see __setup_irq() in kernel/irq/manage.c).
One solution may be to stop verifying IRQF_ONESHOT in __setup_irq(), but
right now the safe course of action is to revert the change. Let's
revisit this in a later merge window.
Reported-by: Paul Walmsley <paul@pwsan.com> Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Requested-by: Alan Cox <alan@lxorguk.ukuu.org.uk> Acked-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Toshiba Satellite L300D with ATI Mobility Radeon X1100 sends data
to i2c bus for a HDMI connector that is not implemented/existent
on the notebook's board.
Fix by applying extented DDC probing for this connector.
Requires [PATCH] drm/radeon: Extended DDC Probing for Connectors
with Improperly Wired DDC Lines
Tested for kernel 2.6.38 on Toshiba Satellite L300D notebook
BugLink: http://bugs.launchpad.net/bugs/826677 Signed-off-by: Thomas Reim <reimth@gmail.com> Acked-by: Chris Routh <routhy@gmail.com> Cc: <stable@kernel.org> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Ben Skeggs [Mon, 22 Aug 2011 03:15:05 +0000 (03:15 +0000)]
drm/ttm: ensure ttm for new node is bound before calling move_notify()
This was true for new TTM_PL_SYSTEM and new TTM_PL_TT cases, but wasn't
the case on TTM_PL_SYSTEM<->TTM_PL_TT moves, which causes trouble on some
paths as nouveau's move_notify() hook requires that the dma addresses be
valid at this point.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Ben Skeggs [Mon, 22 Aug 2011 03:15:04 +0000 (03:15 +0000)]
drm/ttm: unbind ttm before destroying node in accel move cleanup
Nouveau makes the assumption that if a TTM is bound there will be a mm_node
around for it and the backwards ordering here resulted in a use-after-free
on some eviction paths.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Marcin Slusarz [Mon, 22 Aug 2011 21:17:57 +0000 (21:17 +0000)]
drm/ttm: fix ttm_bo_add_ttm(user) failure path
ttm_tt_destroy kfrees passed object, so we need to nullify
a reference to it.
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com> Cc: stable@kernel.org Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
The code really requires the current source directory to be in the
header search path. We already do this if building with an object
tree separate from the source, but it needs to be added manually
if building inside the source. The cflags addition for it accidentally
got removed when collapsing the xfs directory structure.
Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Dave Chinner <david@fromorbit.com> Signed-off-by: Alex Elder <aelder@sgi.com>
Linus Torvalds [Mon, 22 Aug 2011 18:25:44 +0000 (11:25 -0700)]
Merge branch 'stable/bug.fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
* 'stable/bug.fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/tracing: Fix tracing config option properly
xen: Do not enable PV IPIs when vector callback not present
xen/x86: replace order-based range checking of M2P table by linear one
xen: xen-selfballoon.c needs more header files
This change replaced the SMP operations with event based handlers without
taking into account that this only works when the hypervisor supports
callback vectors. This causes unexplainable hangs early on boot for
HVM guests with more than one CPU.
BugLink: http://bugs.launchpad.net/bugs/791850 CC: stable@kernel.org Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com> Tested-and-Reported-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Michel Dänzer [Fri, 19 Aug 2011 15:24:18 +0000 (15:24 +0000)]
drm/radeon: Make vramlimit parameter actually work.
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Michel Dänzer [Fri, 19 Aug 2011 15:24:17 +0000 (15:24 +0000)]
drm/radeon: Explicitly print GTT/VRAM offsets on test failure.
Otherwise these would need to be painstakingly calculated looking at the source
code.
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Michel Dänzer [Fri, 19 Aug 2011 15:24:16 +0000 (15:24 +0000)]
drm/radeon: Take IH ring into account for test size calculation.
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com> Reviewed-by: Alex Deucher <alexdeucher@gmail.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Jay Estabrook [Wed, 6 Jul 2011 23:57:13 +0000 (23:57 +0000)]
drm/radeon/alpha: Add Alpha support to Radeon DRM code
Alpha needs to have available the system bus address for the Radeon's
local memory, so that it can be used in ttm_bo_vm_fault(), when building
the PTEs for accessing that VRAM. So, we make bus.addr hold the ioremap()
return, and then we can modify bus.base appropriately for use during page
fault processing.
Signed-off-by: Jay Estabrook <jay.estabrook@gmail.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Josef Bacik [Sat, 20 Aug 2011 12:29:51 +0000 (08:29 -0400)]
Btrfs: fix 64 bit divide problem
This fixes a regression introduced by commit cdcb725c05fe ("Btrfs: check
if there is enough space for balancing smarter"). We can't do 64-bit
divides on 32-bit architectures.
In cases where we need to divide/multiply by 2 we should just left/right
shift respectively, and in cases where theres N number of devices use
do_div. Also make the counters u64 to match up with rw_devices.
Thanks,
Linus Torvalds [Sun, 21 Aug 2011 13:59:41 +0000 (06:59 -0700)]
Merge branch 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: flush any pending end_io requests before DIO reads w/dioread_nolock
ext4: fix nomblk_io_submit option so it correctly converts uninit blocks
ext4: Resolve the hang of direct i/o read in handling EXT4_IO_END_UNWRITTEN.
ext4: call ext4_ioend_wait and ext4_flush_completed_IO in ext4_evict_inode
ext4: Fix ext4_should_writeback_data() for no-journal mode
Linus Torvalds [Sun, 21 Aug 2011 13:59:02 +0000 (06:59 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: sound/aoa/fabrics/layout.c: remove unneeded kfree
ALSA: hda - Fix error check from snd_hda_get_conn_index() in patch_cirrus.c
ALSA: hda - Don't spew too many ELD errors
ALSA: usb-audio - Fix missing mixer dB information
ALSA: hda - Add "PCM" volume to vmaster slave list
ALSA: hda - Fix duplicated capture-volume creation for ALC268 models
ALSA: ac97: Add HP Compaq dc5100 SFF(PT003AW) to Headphone Jack Sense whitelist
ALSA: snd_usb_caiaq: track submitted output urbs
Randy Dunlap [Sat, 20 Aug 2011 18:49:43 +0000 (11:49 -0700)]
pci: fix new kernel-doc warning in pci.c
Fix new kernel-doc warning in pci.c:
Warning(drivers/pci/pci.c:3259): No description found for parameter 'mps'
Warning(drivers/pci/pci.c:3259): Excess function parameter 'rq' description in 'pcie_set_mps'
(
if (...) { ... when != kfree(x)
when != x = E3
when != E3 = x
* return ...;
}
... when != x = E2
when != I(...,x,...) S
if (...) { ... when != x = E4
kfree(x); ... return ...; }
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Takashi Iwai [Sat, 20 Aug 2011 07:14:45 +0000 (09:14 +0200)]
ALSA: hda - Don't spew too many ELD errors
Currently HD-audio driver shows the all error ELD byte as an error
in the kernel message. This is annoying when the video driver doesn't
set the correct ELD from the beginning. e.g. radeon sends a zero-byte
data, but we still check ELD with the fixed 128 byte as a workaround
for some broken devices, it spews 128-times errors.
For avoiding this, the driver aborts reading when the first byte is
invalid. In such a case, the whole data is certainly invalid.
Linus Torvalds [Sat, 20 Aug 2011 06:07:08 +0000 (23:07 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/drm-intel
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/drm-intel:
drm/i915: set GFX_MODE to pre-Ivybridge default value even on Ivybridge
Jiaying Zhang [Fri, 19 Aug 2011 23:13:32 +0000 (19:13 -0400)]
ext4: flush any pending end_io requests before DIO reads w/dioread_nolock
There is a race between ext4 buffer write and direct_IO read with
dioread_nolock mount option enabled. The problem is that we clear
PageWriteback flag during end_io time but will do
uninitialized-to-initialized extent conversion later with dioread_nolock.
If an O_direct read request comes in during this period, ext4 will return
zero instead of the recently written data.
This patch checks whether there are any pending uninitialized-to-initialized
extent conversion requests before doing O_direct read to close the race.
Note that this is just a bandaid fix. The fundamental issue is that we
clear PageWriteback flag before we really complete an IO, which is
problem-prone. To fix the fundamental issue, we may need to implement an
extent tree cache that we can use to look up pending to-be-converted extents.
Jesse Barnes [Fri, 12 Aug 2011 22:28:32 +0000 (15:28 -0700)]
drm/i915: set GFX_MODE to pre-Ivybridge default value even on Ivybridge
Prior to Ivybridge, the GFX_MODE would default to 0x800, meaning that
MI_FLUSH would flush the TLBs in addition to the rest of the caches
indicated in the MI_FLUSH command. However starting with Ivybridge, the
register defaults to 0x2800 out of reset, meaning that to invalidate the
TLB we need to use PIPE_CONTROL. Since we're not doing that yet, go
back to the old default so things work.
v2: don't forget to actually *clear* the new bit
Reviewed-by: Eric Anholt <eric@anholt.net> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Tested-by: Kenneth Graunke <kenneth@whitecape.org> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Linus Torvalds [Fri, 19 Aug 2011 17:47:07 +0000 (10:47 -0700)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-block
* 'for-linus' of git://git.kernel.dk/linux-block: (23 commits)
Revert "cfq: Remove special treatment for metadata rqs."
block: fix flush machinery for stacking drivers with differring flush flags
block: improve rq_affinity placement
blktrace: add FLUSH/FUA support
Move some REQ flags to the common bio/request area
allow blk_flush_policy to return REQ_FSEQ_DATA independent of *FLUSH
xen/blkback: Make description more obvious.
cfq-iosched: Add documentation about idling
block: Make rq_affinity = 1 work as expected
block: swim3: fix unterminated of_device_id table
block/genhd.c: remove useless cast in diskstats_show()
drivers/cdrom/cdrom.c: relax check on dvd manufacturer value
drivers/block/drbd/drbd_nl.c: use bitmap_parse instead of __bitmap_parse
bsg-lib: add module.h include
cfq-iosched: Reduce linked group count upon group destruction
blk-throttle: correctly determine sync bio
loop: fix deadlock when sysfs and LOOP_CLR_FD race against each other
loop: add BLK_DEV_LOOP_MIN_COUNT=%i to allow distros 0 pre-allocated loop devices
loop: add management interface for on-demand device allocation
loop: replace linked list of allocated devices with an idr index
...
Linus Torvalds [Fri, 19 Aug 2011 17:02:37 +0000 (10:02 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI: OF: Don't crash when bridge parent is NULL.
PCI: export pcie_bus_configure_settings symbol
PCI: code and comments cleanup
PCI: make cardbus-bridge resources optional
PCI: make SRIOV resources optional
PCI : ability to relocate assigned pci-resources
PCI: honor child buses add_size in hot plug configuration
PCI: Set PCI-E Max Payload Size on fabric
s3c-adc-battery: Fix compilation error due to missing header (module.h)
Add linux/module.h to fix this compilation error:
drivers/power/s3c_adc_battery.c:435:15: error: expected declaration specifiers or ‘...’ before string constant
drivers/power/s3c_adc_battery.c:435:1: warning: data definition has no type or storage class
drivers/power/s3c_adc_battery.c:435:1: warning: type defaults to ‘int’ in declaration of ‘MODULE_AUTHOR’
drivers/power/s3c_adc_battery.c:435:15: warning: function declaration isn’t a prototype
drivers/power/s3c_adc_battery.c:436:20: error: expected declaration specifiers or ‘...’ before string constant
drivers/power/s3c_adc_battery.c:436:1: warning: data definition has no type or storage class
drivers/power/s3c_adc_battery.c:436:1: warning: type defaults to ‘int’ in declaration of ‘MODULE_DESCRIPTION’
drivers/power/s3c_adc_battery.c:436:20: warning: function declaration isn’t a prototype
drivers/power/s3c_adc_battery.c:437:16: error: expected declaration specifiers or ‘...’ before string constant
drivers/power/s3c_adc_battery.c:437:1: warning: data definition has no type or storage class
drivers/power/s3c_adc_battery.c:437:1: warning: type defaults to ‘int’ in declaration of ‘MODULE_LICENSE’
drivers/power/s3c_adc_battery.c:437:16: warning: function declaration isn’t a prototype
make[2]: *** [drivers/power/s3c_adc_battery.o] Error 1
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com> Signed-off-by: Ian Lartey <ian@opensource.wolfsonmicro.com> Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Jens Axboe [Fri, 19 Aug 2011 06:34:48 +0000 (08:34 +0200)]
Revert "cfq: Remove special treatment for metadata rqs."
We have a kernel build regression since 3.1-rc1, which is about 10%
regression. The kernel source is in an ext3 filesystem.
Alex Shi bisect it to commit:
commit a07405b7802691d29ab3b23bdc76ee6d006aad0b
Author: Justin TerAvest <teravest@google.com>
Date: Sun Jul 10 22:09:19 2011 +0200
cfq: Remove special treatment for metadata rqs.
Apparently this is caused by lack metadata preemption, where ext3/ext4
do use READ_META. I didn't see a way to fix the issue, so suggest
reverting the patch.
Takashi Iwai [Fri, 19 Aug 2011 05:55:10 +0000 (07:55 +0200)]
ALSA: usb-audio - Fix missing mixer dB information
The recent fix for testing dB range at the mixer creation time seems
to cause regressions in some devices. In such devices, reading the dB
info at probing time gives an error, thus both dBmin and dBmax are still
zero, and TLV flag isn't set although the later read of dB info succeeds.
This patch adds a workaround for such a case by assuming that the later
read will succeed. In future, a similar test should be performed in a
case where a wrong dB range is seen even in the later read.
Linus Torvalds [Fri, 19 Aug 2011 05:47:13 +0000 (22:47 -0700)]
Merge branch 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
* 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
NFSv4.1: Return NFS4ERR_BADSESSION to callbacks during session resets
NFSv4.1: Fix the callback 'highest_used_slotid' behaviour
pnfs-obj: Fix the comp_index != 0 case
pnfs-obj: Bug when we are running out of bio
nfs: add missing prefetch.h include
Ian Campbell [Wed, 17 Aug 2011 22:14:57 +0000 (22:14 +0000)]
sparc: fix array bounds error setting up PCIC NMI trap
CC arch/sparc/kernel/pcic.o
arch/sparc/kernel/pcic.c: In function 'pcic_probe':
arch/sparc/kernel/pcic.c:359:33: error: array subscript is above array bounds [-Werror=array-bounds]
arch/sparc/kernel/pcic.c:359:8: error: array subscript is above array bounds [-Werror=array-bounds]
arch/sparc/kernel/pcic.c:360:33: error: array subscript is above array bounds [-Werror=array-bounds]
arch/sparc/kernel/pcic.c:360:8: error: array subscript is above array bounds [-Werror=array-bounds]
arch/sparc/kernel/pcic.c:361:33: error: array subscript is above array bounds [-Werror=array-bounds]
arch/sparc/kernel/pcic.c:361:8: error: array subscript is above array bounds [-Werror=array-bounds]
cc1: all warnings being treated as errors
I'm not particularly familiar with sparc but t_nmi (defined in head_32.S via
the TRAP_ENTRY macro) and pcic_nmi_trap_patch (defined in entry.S) both appear
to be 4 instructions long and I presume from the usage that instructions are
int sized.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: sparclinux@vger.kernel.org Reviewed-by: Sam Ravnborg <sam@ravnborg.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Julia Lawall [Mon, 8 Aug 2011 11:17:57 +0000 (13:17 +0200)]
drivers/ata/sata_dwc_460ex.c: add missing kfree
Currently, error handling code in this function calls the function
sata_dwc_port_stop, but this function has essentially no effect if hsdevp
has not been stored in ap, which is the case throughout this function. The
only effect is to print a debugging message including ap->print_id.
The code is rewritten to not call sata_dwc_port_stop, but instead to jump
to a local label that prints the original error message and the print_id
information. In the case where hsdevp has been already allocated (but not
yet stored in ap), this value is freed as well.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
x = \(kmalloc\|kzalloc\|kcalloc\)(...);
...
if (x == NULL) S
<... when != x
when != if (...) { <+...kfree(x)...+> }
when any
when != true x == NULL
x->fl
...>
(
if (x == NULL) S1
|
if (...) { ... when != x
when forall
(
return \(0\|<+...x...+>\|ptr\);
|
* return ...;
)
}
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk> Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Add basic support for pata on iMX. It has been tested only on imx51.
SDMA support will probably be added later so this version supports only
PIO.
v2:
- enable only when needed IORDY
- use dev_get_drvdata
v3:
- add missing clk_put() calls
- use platform_get_irq()
- fix resume code to avoid disabling IORDY on resume
v4:
- Remove EXPERIMENTAL and switch to depends on ARCH_MXC
- Use devm_kzalloc()
- make clock a must-have
- Use only 1 ioremap
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Tejun Heo [Thu, 4 Aug 2011 09:15:07 +0000 (11:15 +0200)]
pata_via: disable ATAPI DMA on AVERATEC 3200
On AVERATEC 3200, pata_via causes memory corruption with ATAPI DMA,
which often leads to random kernel oops. The cause of the problem is
not well understood yet and only small subset of machines using the
controller seem affected. Blacklist ATAPI DMA on the machine.
Signed-off-by: Tejun Heo <tj@kernel.org>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=11426 Reported-and-tested-by: Jim Bray <jimsantelmo@gmail.com> Cc: Alan Cox <alan@linux.intel.com> Cc: stable@kernel.org Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Jeff Garzik [Fri, 19 Aug 2011 03:52:36 +0000 (23:52 -0400)]
[libata] sata_sil: fix used-uninit warning
Init 'serror' to silence the following warning:
drivers/ata/sata_sil.c: In function ‘sil_interrupt’:
drivers/ata/sata_sil.c:453:14: warning: ‘serror’ may be used uninitialized in
this function [-Wuninitialized]
This is not a 'can never happen' but is nonetheless extremely unlikely.
The easiest and cleanest warning fix is simply to init the var,
rather than worry about marking the var uninit-ok.
Linus Torvalds [Thu, 18 Aug 2011 21:20:00 +0000 (14:20 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable:
Btrfs: set i_size properly when fallocating and we already
btrfs: unlock on error in btrfs_file_llseek()
btrfs: btrfs_permission's RO check shouldn't apply to device nodes
Btrfs: truncate pages from clone ioctl target range
Btrfs: fix uninitialized sync_pending
Btrfs: fix wrong free space information
btrfs: memory leak in btrfs_add_inode_defrag()
Btrfs: use plain page_address() in header fields setget functions
Btrfs: forced readonly when btrfs_drop_snapshot() fails
Btrfs: check if there is enough space for balancing smarter
Btrfs: fix a bug of balance on full multi-disk partitions
Btrfs: fix an oops of log replay
Btrfs: detect wether a device supports discard
Btrfs: force unplugs when switching from high to regular priority bios
* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
update cifs version to 1.75
[CIFS] possible memory corruption on mount
cifs: demote cERROR in build_path_from_dentry to cFYI
Steve French [Thu, 18 Aug 2011 04:41:55 +0000 (04:41 +0000)]
[CIFS] possible memory corruption on mount
CIFS cleanup_volume_info_contents() looks like having a memory
corruption problem.
When UNCip is set to "&vol->UNC[2]" in cifs_parse_mount_options(), it
should not be kfree()-ed in cleanup_volume_info_contents().
Signed-off-by: J.R. Okajima <hooanon05@yahoo.co.jp> Reviewed-by: Jeff Layton <jlayton@redhat.com> CC: Stable <stable@kernel.org> Signed-off-by: Steve French <sfrench@us.ibm.com>
Josef Bacik [Thu, 18 Aug 2011 14:36:39 +0000 (10:36 -0400)]
Btrfs: set i_size properly when fallocating and we already
xfstests exposed a problem with preallocate when it fallocates a range that
already has an extent. We don't set the new i_size properly because we see that
we already have an extent. This isn't right and we should update i_size if the
space already exists. With this patch we now pass xfstests 075. Thanks,
Signed-off-by: Josef Bacik <josef@redhat.com> Signed-off-by: Chris Mason <chris.mason@oracle.com>
Jeff Mahoney [Mon, 15 Aug 2011 17:27:21 +0000 (17:27 +0000)]
btrfs: btrfs_permission's RO check shouldn't apply to device nodes
This patch tightens the read-only access checks in btrfs_permission to
match the constraints in inode_permission. Currently, even though the
device node itself will be unmodified, read-write access to device nodes
is denied to when the device node resides on a read-only subvolume or a
is a file that has been marked read-only by the btrfs conversion utility.
With this patch applied, the check only affects regular files,
directories, and symlinks. It also restructures the code a bit so that
we don't duplicate the MAY_WRITE check for both tests.
Signed-off-by: Jeff Mahoney <jeffm@suse.com> Signed-off-by: Chris Mason <chris.mason@oracle.com>
Josh Boyer [Thu, 18 Aug 2011 11:37:21 +0000 (07:37 -0400)]
perf tools: Fix build against newer glibc
Upstream glibc commit 295e904 added a definition for __attribute_const__
to cdefs.h. This causes the following error when building perf:
util/include/linux/compiler.h:8:0: error: "__attribute_const__"
redefined [-Werror] /usr/include/sys/cdefs.h:226:0: note: this is the
location of the previous definition
Wrap __attribute_const__ in #ifndef as we do for __always_inline.
There was a problem with the parse_events() code not printing the
correct event name when an event was unknown and starting with an 'r'.
The source of the problem was the way raw notation was parsed.
Without the patch:
$ perf stat -e retired_foo
invalid event modifier: 'tired_foo'
With the patch:
$ perf stat -e retired_foo
invalid or unsupported event: 'retired_foo'
This also covers the case where the name of the event was not printed at
all when perf was linked with libpfm4.
Cc: Ingo Molnar <mingo@elte.hu> Cc: Peter Zijlstra <peterz@infradead.org> Link: http://lkml.kernel.org/r/20110723021043.GA20178@quad Signed-off-by: Stephane Eranian <eranian@google.com> Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
perf evlist: Fix missing event name init for default event
When no event is given to perf record, perf top, a default event is
initialized (cycles). However, perf_evlist__add_default() was not
setting the symbolic name for the event. Perf top worked simply because
it was reconstructing the name from the event code. But it should not
have to do this. This patch initializes the evsel->name field properly.
This second version improves the code flow on the non error path.
Cc: Ingo Molnar <mingo@elte.hu> Cc: Peter Zijlstra <peterz@infradead.org> Link: http://lkml.kernel.org/r/20110607161936.GA8163@quad Signed-off-by: Stephane Eranian <eranian@google.com>
[committer note: Use perf_evsel__delete() instead of plain free()] Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Linus Torvalds [Wed, 17 Aug 2011 17:31:39 +0000 (10:31 -0700)]
Merge branch 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf probe: Filter out redundant inline-instances
perf probe: Search concrete out-of-line instances
perf probe: Avoid searching variables in intermediate scopes
perf probe: Fix to search local variables in appropriate scope
perf probe: Warn when more than one line are given
perf probe: Fix to walk all inline instances
perf probe: Fix to search nested inlined functions in CU
perf probe: Fix line walker to check CU correctly
perf probe: Fix a memory leak for scopes array
perf: fix temporary file ownership check
perf report: Use properly build_id kernel binaries
perf top browser: Remove spurious helpline update
Linus Torvalds [Wed, 17 Aug 2011 17:28:33 +0000 (10:28 -0700)]
Merge branch 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
rtc: Limit RTC PIE frequency
rtc: Fix hrtimer deadlock
rtc: Handle errors correctly in rtc_irq_set_state()
Fixup trivial conflicts in drivers/rtc/interface.c due to slightly
trivially versions of the same patch coming in two different ways.
Linus Torvalds [Wed, 17 Aug 2011 17:23:50 +0000 (10:23 -0700)]
Merge branch 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
irq: Track the owner of irq descriptor
irq: Always set IRQF_ONESHOT if no primary handler is specified
genirq: Fix wrong bit operation
Or Gerlitz [Mon, 1 Aug 2011 21:14:09 +0000 (21:14 +0000)]
IB/iser: Support iSCSI PDU padding
RFC3270 mandates that iSCSI PDUs are padded to the closest integer
number of four byte words. Fix the iser code to support that on both
the TX/RX flows.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.co.il> Signed-off-by: Roland Dreier <roland@purestorage.com>
The code that prepares the SG associated with SCSI command for FMR was
buggy for systems with DMA addresses that don't fit in unsigned long,
e.g under the 32-bit based XenServer dom0 sizeof(dma_addr_t) is 8.
Fix that by casting to unsigned long long a masking constant used by
the code. This resolves a crash in iser_sg_to_page_vec on this system.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.co.il> Signed-off-by: Roland Dreier <roland@purestorage.com>
whereas a direct check requires just a compare, like in
cmp ebx, [machine_to_phys_nr]
jae ...
), but also slightly dangerous in the 32-on-64 case - the element
address calculation can wrap if the next power of two boundary is
sufficiently far away from the actual upper limit of the table, and
hence can result in user space addresses being accessed (with it being
unknown what may actually be mapped there).
Additionally, the elimination of the mistaken use of fls() here (should
have been __fls()) fixes a latent issue on x86-64 that would trigger
if the code was run on a system with memory extending beyond the 44-bit
boundary.
CC: stable@kernel.org Signed-off-by: Jan Beulich <jbeulich@novell.com>
[v1: Based on Jeremy's feedback] Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Namjae Jeon [Wed, 17 Aug 2011 10:10:09 +0000 (19:10 +0900)]
fat: fat16 support maximum 4GB file/vol size as WinXP or 7.
FAT16 support maximum 4GB vol/file size with 64KB cluster size.
Win NT/XP/7 increased the maximum cluster size to 64KB, and file/vol
size increased 4GB also. Although increasing, the file size of linux
FAT is still limited at 2GB.
I found that it is limited by sb->maxbytes(0x7fffffff) when partition
is formatted by FAT16. sb->s_maxbytes in fill_super should be set to
0xffffffff like fat32.
Mihai Moldovan [Wed, 17 Aug 2011 10:10:08 +0000 (19:10 +0900)]
fat: fix utf8 iocharset warning message
The fat_msg function already formats the given message and appends
a newline to it - we don't need to do this in the passed message
string as well, or will end up with a blank line printed in the
kernel log ring buffer.
Also change the loglevel from error to warning.
Signed-off-by: Mihai Moldovan <ionic@ionic.de> Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Sage Weil [Wed, 10 Aug 2011 18:04:04 +0000 (18:04 +0000)]
Btrfs: truncate pages from clone ioctl target range
We need to truncate page cache pages for the clone ioctl target range or
else we'll confuse ourselves to no end. If the old data was cached, we
used to still see it (until remount). If the page was partially updated
we used to get a mix of old and new data.
Signed-off-by: Sage Weil <sage@newdream.net> Signed-off-by: Chris Mason <chris.mason@oracle.com>
Miao Xie [Fri, 5 Aug 2011 09:32:35 +0000 (09:32 +0000)]
Btrfs: fix wrong free space information
Btrfs subtracted the size of the allocated space twice when it allocated
the space from the bitmap in the cluster, it broke the free space information
and led to oops finally.
And this patch also fixes the bug that ctl->free_space was subtracted
without lock.
Reported-by: Liu Bo <liubo2009@cn.fujitsu.com> Signed-off-by: Miao Xie <miaox@cn.fujitsu.com> Signed-off-by: Chris Mason <chris.mason@oracle.com>
projects / linux-beck.git / log