Clemens Ladisch [Mon, 25 Feb 2008 09:59:52 +0000 (10:59 +0100)]
[ALSA] mpu401: reduce tx loop timeout
Reduce the number of times to check for a non-empty Tx FIFO from 100 to
2 because there is no MPU-401 implementation that needs more than one or
two reads to determine the actual FIFO status.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Remy Bruno [Fri, 22 Feb 2008 16:57:02 +0000 (17:57 +0100)]
[ALSA] hdsp - RME 9632 fix at 192kHz
The bits indicating SPDIF frequency in the status register are not the same for
the 9632 than for the other cards, because it also supports 192kHz. A specific
bitmask has thus been added (used in hdsp_spdif_sample_rate()).
The 9632 does not seem to report external sample rates greater than 96kHz. In
this case, the best seems to report spdif rate when autosync reference is
spdif. This also required to move function hdsp_spdif_sample_rate().
Signed-off-by: Remy Bruno <remy.bruno@trinnov.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Vladimir Barinov [Mon, 18 Feb 2008 10:40:22 +0000 (11:40 +0100)]
[ALSA] Davinci ASoC support
Add ASoC support for the TI Davinci SoC and the Davicni-EVM reference board.
It includes:
- ASoC Davinci DMA driver
- ASoC Davinci I2S (Davinci McBSP module based) driver
- ASoC Davinci-EVM reference board
Signed-off-by: Vladimir Barinov <vbarinov@ru.mvista.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Takashi Iwai [Wed, 13 Feb 2008 16:19:35 +0000 (17:19 +0100)]
[ALSA] hda-codec - Fix breakage of resume in auto-config of realtek codecs
The last patch for fixing the auto-config pin setting breaks the resume
due to a wrong use of snd_hda_codec_amp_stereo(). The code in the init
hook shouldn't touch the amp cache.
Added a new mixer switch to enable/disable the sharing of the default
PCM stream with analog and SPDIF outputs. When "IEC958 Default PCM"
switch is on, the PCM stream is routed both to analog and SPDIF outputs.
This is the behavior in the earlier version.
Turning this switch off has a merit for some codecs, though. Some codec
chips don't support 24bit formats for SPDIF but only for analog outputs.
In this case, you can use 24bit format by disabling this switch.
Takashi Iwai [Tue, 12 Feb 2008 17:32:23 +0000 (18:32 +0100)]
[ALSA] hda-codec - Fix auto-configuration of Realtek codecs
This patch fixes some bugs in the auto-configurator of Realtek codecs:
- add missing pin set-up for speaker pins
- fix the speaker auto-mute function not to conflict with the existing
"Speaker" mixer switch
Takashi Iwai [Tue, 12 Feb 2008 17:30:12 +0000 (18:30 +0100)]
[ALSA] hda-codec - More fix-up for auto-configuration
In some cases, the BIOS sets up only the HP pins with different assoc
and sequence numbers, e.g. on FSC Esprimo with ALC262.
This patch adds a fix-up for such a case. When multiple HPs are defined
and no line-outs is found, the configurator tries to re-assign some pins
from HP list to line-out, judging from the sequence number.
Alan Horstmann [Wed, 6 Feb 2008 13:43:54 +0000 (14:43 +0100)]
[ALSA] ice1712 - Fix hoontech MIDI input
Fixes the problems with Midi In on Hoontech/STA dsp24 cards, for example with
DSP2000 box, without restricting the box configurations available. Also adds
mpu_401 name strings.
Signed-off-by: Alan Horstmann <gineera@aspect135.co.uk> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Takashi Iwai [Wed, 6 Feb 2008 13:03:20 +0000 (14:03 +0100)]
[ALSA] hda-intel - Fix PCM device number assignment
In the current scheme, PCM device numbers are assigned incrementally
in the order of codecs. This causes problems when the codec number
is irregular, e.g. codec #0 for HDMI and codec #1 for analog. Then
the HDMI becomes the first PCM, which is picked up as the default
output device. Unfortuantely this doesn't work well with normal
setups.
This patch introduced the fixed device numbers for the PCM types,
namely, analog, SPDIF, HDMI and modem. The PCM devices are assigned
according to the corresponding PCM type. After this patch, HDMI will
be always assigned to PCM #3, SPDIF to PCM #1, and the first analog
to PCM #0, etc.
Takashi Iwai [Mon, 4 Feb 2008 11:31:13 +0000 (12:31 +0100)]
[ALSA] hda-codec - Allow multiple SPDIF devices
The current code doesn't allow multiple SPDIF devices, and causes
errors when multiple SPDIF devices are found (e.g. SPDIF out and HDMI).
This patch allows multiple SPDIF devices by incrementing the index
automatically.
Currently you will see an empty "SoC Audio support for SuperH" menu
when building for other archs (example pxa).
This patch adds "depends on SUPERH" to remove that empty menu.
Mike Montour [Fri, 1 Feb 2008 12:12:12 +0000 (13:12 +0100)]
[ALSA] soc - Mono voice playback volume for WM8753
Voice playback volume is in register bits 0:2, not 4:6.
From: Mike Montour <mail@mmontour.net> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Cc: Werner Almesberger <werner@openmoko.org> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
[patch 7/7] vfs: mountinfo: show dominating group id
[patch 6/7] vfs: mountinfo: add /proc/<pid>/mountinfo
[patch 5/7] vfs: mountinfo: allow using process root
[patch 4/7] vfs: mountinfo: add mount peer group ID
[patch 3/7] vfs: mountinfo: add mount ID
[patch 2/7] vfs: mountinfo: add seq_file_root()
[patch 1/7] vfs: mountinfo: add dentry_path()
[PATCH] remove unused label in xattr.c (noise from ro-bind)
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
iwlwifi: Fix built-in compilation of iwlcore
net: Unexport move_addr_to_{kernel,user}
rt2x00: Select LEDS_CLASS.
iwlwifi: Select LEDS_CLASS.
leds: Do not guard NEW_LEDS with HAS_IOMEM
[IPSEC]: Fix catch-22 with algorithm IDs above 31
time: Export set_normalized_timespec.
tcp: Make use of before macro in tcp_input.c
hamradio: Remove unneeded and deprecated cli()/sti() calls in dmascc.c
[NETNS]: Remove empty ->init callback.
[DCCP]: Convert do_gettimeofday() to getnstimeofday().
[NETNS]: Don't initialize err variable twice.
[NETNS]: The ip6_fib_timer can work with garbage on net namespace stop.
[IPV4]: Convert do_gettimeofday() to getnstimeofday().
[IPV4]: Make icmp_sk_init() static.
[IPV6]: Make struct ip6_prohibit_entry_template static.
tcp: Trivial fix to correct function name in a comment in net/ipv4/tcp.c
[NET]: Expose netdevice dev_id through sysfs
skbuff: fix missing kernel-doc notation
[ROSE]: Fix soft lockup wrt. rose_node_list_lock
Len Brown [Wed, 23 Apr 2008 04:09:13 +0000 (00:09 -0400)]
pnpacpi: fix potential corruption on "pnpacpi: exceeded the max number of IRQ resources 2"
PNP_MAX_IRQ is 2
If a device invokes pnpacpi_parse_allocated_irqresource() 0, 1, or 2 times, we are happy.
The 3rd time, we will fail and print "pnpacpi: exceeded the max number of IRQ resources: 2"
The 4th and subsequent calls (if this ever happened) would silently scribble on
irq_resource[2], which doesn't actualy exist.
Found-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[mszeredi@suse.cz] rewrite and split big patch into managable chunks
/proc/mounts in its current form lacks important information:
- propagation state
- root of mount for bind mounts
- the st_dev value used within the filesystem
- identifier for each mount and it's parent
It also suffers from the following problems:
- not easily extendable
- ambiguity of mountpoints within a chrooted environment
- doesn't distinguish between filesystem dependent and independent options
- doesn't distinguish between per mount and per super block options
This patch introduces /proc/<pid>/mountinfo which attempts to address
all these deficiencies.
Code shared between /proc/<pid>/mounts and /proc/<pid>/mountinfo is
extracted into separate functions.
Thanks to Al Viro for the help in getting the design right.
Signed-off-by: Ram Pai <linuxram@us.ibm.com> Signed-off-by: Miklos Szeredi <mszeredi@suse.cz> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Miklos Szeredi [Thu, 27 Mar 2008 12:06:24 +0000 (13:06 +0100)]
[patch 5/7] vfs: mountinfo: allow using process root
Allow /proc/<pid>/mountinfo to use the root of <pid> to calculate
mountpoints.
- move definition of 'struct proc_mounts' to <linux/mnt_namespace.h>
- add the process's namespace and root to this structure
- pass a pointer to 'struct proc_mounts' into seq_operations
In addition the following cleanups are made:
- use a common open function for /proc/<pid>/{mounts,mountstat}
- surround namespace.c part of these proc files with #ifdef CONFIG_PROC_FS
- make the seq_operations structures const
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Miklos Szeredi [Thu, 27 Mar 2008 12:06:23 +0000 (13:06 +0100)]
[patch 4/7] vfs: mountinfo: add mount peer group ID
Add a unique ID to each peer group using the IDR infrastructure. The
identifiers are reused after the peer group dissolves.
The IDR structures are protected by holding namepspace_sem for write
while allocating or deallocating IDs.
IDs are allocated when a previously unshared vfsmount becomes the
first member of a peer group. When a new member is added to an
existing group, the ID is copied from one of the old members.
IDs are freed when the last member of a peer group is unshared.
Setting the MNT_SHARED flag on members of a subtree is done as a
separate step, after all the IDs have been allocated. This way an
allocation failure can be cleaned up easilty, without affecting the
propagation state.
Based on design sketch by Al Viro.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Miklos Szeredi [Thu, 27 Mar 2008 12:06:21 +0000 (13:06 +0100)]
[patch 2/7] vfs: mountinfo: add seq_file_root()
Add a new function:
seq_file_root()
This is similar to seq_path(), but calculates the path relative to the
given root, instead of current->fs->root. If the path was unreachable
from root, then modify the root parameter to reflect this.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Ram Pai [Thu, 27 Mar 2008 12:06:20 +0000 (13:06 +0100)]
[patch 1/7] vfs: mountinfo: add dentry_path()
[mszeredi@suse.cz] split big patch into managable chunks
Add the following functions:
dentry_path()
seq_dentry()
These are similar to d_path() and seq_path(). But instead of
calculating the path within a mount namespace, they calculate the path
from the root of the filesystem to a given dentry, ignoring mounts
completely.
Signed-off-by: Ram Pai <linuxram@us.ibm.com> Signed-off-by: Miklos Szeredi <mszeredi@suse.cz> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
[PATCH] get rid of __exit_files(), __exit_fs() and __put_fs_struct()
[PATCH] proc_readfd_common() race fix
[PATCH] double-free of inode on alloc_file() failure exit in create_write_pipe()
[PATCH] teach seq_file to discard entries
[PATCH] umount_tree() will unhash everything itself
[PATCH] get rid of more nameidata passing in namespace.c
[PATCH] switch a bunch of LSM hooks from nameidata to path
[PATCH] lock exclusively in collect_mounts() and drop_collected_mounts()
[PATCH] move a bunch of declarations to fs/internal.h
Commit 884525655d07fdee9245716b998ecdc45cdd8007 ("PCI: clean up resource
alignment management") didn't set the alignment information for the
cardbus window resources, causing their subsequent allocations to fail
miserably with a message like
yenta_cardbus 0000:15:00.0: device not available because of BAR 7 [100:1ff] collisions
yenta_cardbus: probe of 0000:15:00.0 failed with error -16
or similar.
This fixes it and clarifies the code a bit too (we used to have to use
the insane PCI bridge alignment logic that put the alignment in the
"start" field, this makes it use the slightly easier-to-understand
size-based alignment, and allows us to set the resource start to zero
until it gets allocated).
Reported-and-tested-by: Jeff Chua <jeff.chua.linux@gmail.com> Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru> Cc: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Al Viro [Tue, 22 Apr 2008 09:35:42 +0000 (05:35 -0400)]
[PATCH] get rid of __exit_files(), __exit_fs() and __put_fs_struct()
The only reason to have separated __...() for those was to keep them inlined
for local users in exit.c. Since Alexey removed the inline on those, there's
no reason whatsoever to keep them around; just collapse with normal variants.
Merge branch 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] run drivers/misc/sgi-xp through scripts/checkpatch.pl
[IA64] run rest drivers/misc/sgi-xp through scripts/Lindent
[IA64] run some drivers/misc/sgi-xp through scripts/Lindent
[IA64] move XP and XPC to drivers/misc/sgi-xp
[IA64] minor irq handler cleanups
[IA64] simplify notify hooks in mca.c
[IA64] do notify DIE_MCA_MONARCH_PROCESS for each monarchs
[IA64] disable interrupts on exit of ia64_trace_syscall
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/selinux-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/selinux-2.6:
SELinux fixups needed for preemptable RCU from -rt
SELinux: no BUG_ON(!ss_initialized) in selinux_clone_mnt_opts
Dean Nelson [Tue, 22 Apr 2008 19:50:17 +0000 (14:50 -0500)]
[IA64] run drivers/misc/sgi-xp through scripts/checkpatch.pl
Addressed issues raised by scripts/checkpatch.pl. Removed unnecessary curly
braces. Eliminated uses of volatiles and use of kernel_thread() and daemonize().
Signed-off-by: Dean Nelson <dcn@sgi.com> Signed-off-by: Tony Luck <tony.luck@intel.com>
Merge branch 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6
* 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
i2c: Fix platform driver hotplug/coldplug
i2c: New driver for the SuperH Mobile I2C bus controller
i2c/scx200_acb: Don't use 0 as NULL pointer
i2c-bfin-twi: Fix mismatch in add timer and delete timer
i2c-bfin-twi: Just let i2c-bfin-twi driver depends on BLACKFIN
i2c-bfin-twi: Use simpler comment headers and strip out information that is maintained in the scm's log
i2c-bfin-twi: Cleanup driver descriptions, versions and some module useful information
i2c-bfin-twi: Add missing pin mux operation
i2c-bfin-twi: Add platform_resource interface to support multi-port TWI controllers
i2c-bfin-twi: Add repeat start feature to avoid break of a bundle of i2c master xfer operation
i2c: Remove trailing whitespaces in busses/Kconfig
i2c: Replace remaining __FUNCTION__ occurrences
i2c: Renesas SH7760 I2C master driver
i2c-dev: Split i2cdev_ioctl
i2c-ibm_iic: Support building as an of_platform driver
i2c-ibm_iic: Change the log levels
i2c: Add platform driver on top of the new pca-algorithm
i2c-algo-pca: Extend for future drivers
i2c-algo-pca: Remove trailing whitespaces and unnecessary UTF
i2c: Remove the algorithm drivers from the config menu
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/teigland/dlm
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/teigland/dlm:
dlm: linux/{dlm,dlm_device}.h: cleanup for userspace
dlm: common max length definitions
dlm: move plock code from gfs2
dlm: recover nodes that are removed and re-added
dlm: save master info after failed no-queue request
dlm: make dlm_print_rsb() static
dlm: match signedness between dlm_config_info and cluster_set
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: Suppress hidinput for Samsung IR control
HID: remove 60x GTCO devices from blacklist
HID: export headers properly
HID: WiseGroup 866 Dual Joypad needs output reports quirk
HID: ThrustMaster FF driver is no longer experimental
HID: Logitech diNovo Mini pad support
HID: fix race between open() and disconnect() in usbhid
HID: make hid_input_field and usbhid_modify_dquirk static
HID: pass numbered reports properly to hidraw
HID: fix misplaced rdesc quirk
HID: force feedback driver for Logitech Rumblepad 2
HID: move wait from hid to usbhid
HID: make function from dbg_hid
HID: fix sparse warnings
HID: only dump report traffic with debug level 2
HID: patch to add NOGET for DMI/Acomdata
HID: Sunplus Wireless Desktop needs report descriptor fixup
HID: quirk for MS Wireless Desktop Receiver (model 1028)
HID: fixup fullspeed interval on highspeed Afatech DVB-T IR kbd
HID: fix build failure in hiddev_ioctl with gcc 3.2
Merge branch 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-udf-2.6
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-udf-2.6: (41 commits)
udf: use crc_itu_t from lib instead of udf_crc
udf: Fix compilation warnings when UDF debug is on
udf: Fix bug in VAT mapping code
udf: Add read-only support for 2.50 UDF media
udf: Fix handling of multisession media
udf: Mount filesystem read-only if it has pseudooverwrite partition
udf: Handle VAT packed inside inode properly
udf: Allow loading of VAT inode
udf: Fix detection of VAT version
udf: Silence warning about accesses beyond end of device
udf: Improve anchor block detection
udf: Cleanup anchor block detection.
udf: Move processing of virtual partitions
udf: Move filling of partition descriptor info into a separate function
udf: Improve error recovery on mount
udf: Cleanup volume descriptor sequence processing
udf: fix anchor point detection
udf: Remove declarations of arrays of size UDF_NAME_LEN (256 bytes)
udf: Remove checking of existence of filename in udf_add_entry()
udf: Mark udf_process_sequence() as noinline
...
Petr Tesarik [Tue, 22 Apr 2008 03:36:52 +0000 (05:36 +0200)]
fix brd allocation flags
While looking at the implementation of the Ram backed block device
driver, I stumbled across a write-only local variable, which makes
little sense, so I assume it should actually work like this:
Signed-off-by: Petr Tesarik <ptesarik@suse.cz> Signed-off-by: Nick Piggin <npiggin@suse.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Kay Sievers [Tue, 22 Apr 2008 20:16:49 +0000 (22:16 +0200)]
i2c: Fix platform driver hotplug/coldplug
Since 43cc71eed1250755986da4c0f9898f9a635cb3bf, the platform
modalias is prefixed with "platform:". Add MODULE_ALIAS() to the
hotpluggable I2C platform drivers, to allow module auto loading.
[ db: add some more drivers ]
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Jean Delvare <khali@linux-fr.org>
projects / mv-sheeva.git / log