usb: gadget: f_uvc: Store EP0 control request state during setup stage
To handle class requests received on ep0, the driver needs to access the
length and direction of the request after the setup stage. It currently
stores them in a v4l2 event during the setup stage, and then copies them
from the event structure to the driver internal state structure when the
event is dequeued.
This two-steps approach isn't necessary. Simplify the driver by storing
the needed information in the driver internal state structure directly
during the setup stage.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Acked-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
Daniel Mack [Wed, 3 Sep 2014 15:21:24 +0000 (17:21 +0200)]
usb: musb: cppi41: tweak hrtimer values
Intensive tests with USB audio devices connected to a musb host port
have shown reproducible pops and clicks in both the playback and the
capture stream.
These are related to how the early_tx hrtimer is set up, and it turns
out they can be fixed by reducing the timer's slack value from 40 to
25 us. Also, when the callback is ran without taking action, it should
be rescheduled 20 us later instead of 50 us.
Reported-and-tested-by: Sven Neumann <neumann@teufel.de> Signed-off-by: Daniel Mack <daniel@zonque.org> Signed-off-by: Felipe Balbi <balbi@ti.com>
Peter Griffin [Fri, 5 Sep 2014 15:36:32 +0000 (16:36 +0100)]
MAINTAINERS: Add dwc3-st.c file to ARCH/STI architecture
This patch adds the new dwc3-st.c glue driver found on
STMicroelectronics stih407 consumer electronics SoC's into the STI
arch section of the maintainers file.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org> Acked-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch documents the device tree documentation required for
the ST usb3 controller glue layer found in STiH407 devices.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: Peter Griffin <peter.griffin@linaro.org> Acked-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Felipe Balbi <balbi@ti.com>
Peter Griffin [Fri, 5 Sep 2014 15:36:30 +0000 (16:36 +0100)]
usb: dwc3: add ST dwc3 glue layer to manage dwc3 HC
This patch adds the ST glue logic to manage the DWC3 HC
on STiH407 SoC family. It manages the powerdown signal,
and configures the internal glue logic and syscfg registers.
[ balbi@ti.com : actually switch over to of_platform_depopulate() ]
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: Peter Griffin <peter.griffin@linaro.org> Acked-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Felipe Balbi <balbi@ti.com>
Felipe Balbi [Wed, 30 Apr 2014 22:45:10 +0000 (17:45 -0500)]
usb: dwc3: add tracepoints to aid debugging
When we're debugging hard-to-reproduce and time-sensitive
use cases, printk() poses too much overhead. That's when
the kernel's tracing infrastructure comes into play.
This patch implements a few initial tracepoints for the
dwc3 driver. More traces can be added as necessary in order
to ease the task of debugging dwc3.
Reviewed-by: Paul Zimmerman <paulz@synopsys.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
The UAC2 function driver currently responds to all packets at all times
with wMaxPacketSize packets. That results in way too fast audio
playback as the function driver (which is in fact supposed to define
the audio stream pace) delivers as fast as it can.
Fix this by sizing each packet correctly with the following steps:
a) Set the packet's size by dividing the nominal data rate by the
playback endpoint's interval.
b) If there is a residual value from the calculation in a), add
it to a accumulator to keep track of it across packets.
c) If the accumulator has gathered at least the number of bytes
that are needed for one sample frame, increase the packet size.
This way, the packet size calculation will get rid of any kind of
imprecision that would otherwise occur with a simple division over
time.
Some of the variables that are needed while processing each packet
are pre-computed for performance reasons.
Signed-off-by: Daniel Mack <zonque@gmail.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
Daniel Mack [Wed, 27 Aug 2014 17:09:06 +0000 (19:09 +0200)]
usb: gadget: f_uac2: handle partial dma area wrap
With packet sizes other than 512, payloads in the packets may wrap
around the ALSA dma buffer partially, which leads to memory corruption
and audible clicks and pops in the audio stream at the moment, because
there is no boundary check before the memcpy().
In preparation to an implementation for smaller and dynamically sized
packets, we have to address such cases, and copy the payload in two
steps conditionally.
The 'src' and 'dst' approach doesn't work here anymore, as different
behavior is necessary in playback and capture cases. Thus, this patch
open-codes the routine now.
Signed-off-by: Daniel Mack <zonque@gmail.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
Daniel Mack [Wed, 27 Aug 2014 17:09:04 +0000 (19:09 +0200)]
usb: gadget: f_uac2: add short-hand for 'dev'
In afunc_bind() and afunc_set_alt(), &uac2->pdev.dev are used multiple
times. Adding a short-hand for them makes lines shorter so we can
remove some line wraps.
No functional change.
Signed-off-by: Daniel Mack <zonque@gmail.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
Daniel Mack [Wed, 27 Aug 2014 17:09:03 +0000 (19:09 +0200)]
usb: gadget: f_uac2: restructure some code in afunc_set_alt()
Restructure some code to make it easier to read.
While at it, return -ENOMEM instead of -EINVAL if
usb_ep_alloc_request() fails, and omit the logging in such cases
(the mm core will complain loud enough).
Signed-off-by: Daniel Mack <zonque@gmail.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
Flatten the start_transfer function by reversing the if condition and
returning early out of the function if everything went fine. It makes
the function look less complicated, at least to me, and easier to
understand.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
tools: ffs-test: add compatibility code for old kernels
If ffs-test is used with a kernel prior to 3.14, which do not
support the new descriptors format, it will fail when trying to
write the descriptors. Add a function that converts the new
descriptors to the legacy ones and use it to retry writing the
descriptors using the legacy format.
Also add “-l” flag to ffs-test which will cause the tool to
never try the new format and instead immediatelly try the
legacy one. This should be useful to test whether parsing
of the old format still works on given 3.14+ kernel.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
Since commit [ac8dde11: “Add flags to descriptors block”] functionfs
supports a new, more powerful and extensible, descriptor format.
Since ffs-test is probably the first thing users of the functionfs
interface see when they start writing functionfs user space daemons,
convert it to use the new format thus promoting it.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
Li Jun [Thu, 28 Aug 2014 13:44:11 +0000 (21:44 +0800)]
usb: gadget: composite: dequeue cdev->req before free its buffer
commit f226708(usb: gadget: composite: dequeue cdev->req before free it in
composite_dev_cleanup) fixed a bug: free the usb request(i.e. cdev->req) but
does not dequeue it beforehand. This fix is not proper enough because it
dequeues the request after free its data buffer, considering the hardware can
access the buffer's memory anytime before the request's complettion rountine
runs, and usb_ep_dequeue always call the complettion rountine before it returns,
so the best way is to dequeue the request before free its buffer.
Suggested-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Li Jun <b47624@freescale.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
usb: gadget: USB_RENESAS_USBHS_UDC should depend on HAS_DMA
If NO_DMA=y:
drivers/built-in.o: In function `usbhsg_dma_map_ctrl':
mod_gadget.c:(.text+0x53b226): undefined reference to `usb_gadget_map_request'
mod_gadget.c:(.text+0x53b242): undefined reference to `usb_gadget_unmap_request'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Felipe Balbi <balbi@ti.com>
drivers/usb/phy/phy-samsung-usb[2,3] drivers got replaced by
drivers/phy/phy-samsung-usb[2,3] ones and the old common Samsung
USB PHY code is no longer used.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Acked-by: Kyungmin Park <kyungmin.park@samsung.com> Reviewed-by: Vivek Gautam <gautam.vivek@samsung.com> Reviewed-by: Jingoo Han <jg1.han@samsung.com> Acked-by: Kishon Vijay Abraham I <kishon@ti.com> Cc: Kamil Debski <k.debski@samsung.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
Amit Virdi [Fri, 22 Aug 2014 09:06:37 +0000 (14:36 +0530)]
usbtest: Add interrupt EP testcases
Two simple test cases for interrupt endpoints are added to the usbtest.c file.
These are simple non-queued interrupt IN and interrupt OUT transfers. Currently,
only gadget zero is capable of executing the interrupt EP test cases. However,
extending the same to other gadgets is extremely simple and can be done
on-demand.
The two new tests added are
- Test 25: To verify Interrupt OUT transfer
- Test 26: To verify Interrupt IN transfer
Since the default value of wMaxPacketSize is set as 1024, so interrupt
IN transfers must be specified with the size parameter = multiple of
1024. Otherwise the default value (512) in the usbtest application fails
the transfer. See [RUN 4] for sample logs
The application logs (usbtest) and corresponding kernel logs are as
following:
[Run 1]
./testusb -a -c 10 -s 2048 -t 26 -v 511
usbtest 7-1:3.0: TEST 26: read 2048 bytes 10 times
[Run 2]
./testusb -a -c 10 -s 1024 -t 25 -v 511
usbtest 7-1:3.0: TEST 25: write 1024 bytes 10 times
[Run 3]
./testusb -a -c 10 -s 1098 -t 25 -v 511
usbtest 7-1:3.0: TEST 25: write 1098 bytes 10 times
[Run 4 - Failure case scenario]
./testusb -a -t 26
unknown speed /dev/bus/usb/007/004 0
/dev/bus/usb/007/004 test 26 --> 75 (Value too large for defined data type)
usbtest 7-1:3.0: TEST 26: read 512 bytes 1000 times
usb 7-1: test26 failed, iterations left 999, status -75 (not 0)
Signed-off-by: Amit Virdi <amit.virdi@st.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
Amit Virdi [Fri, 22 Aug 2014 09:06:36 +0000 (14:36 +0530)]
usb: gadget: zero: Add support for interrupt EP
Interrupt endpoints behave quite similar to the bulk endpoints with the
difference that the endpoints expect data sending/reception request at
particular intervals till the whole data has not been transmitted.
The interrupt EP support is added to gadget zero. A new alternate setting (=2)
has been added. It has 2 interrupt endpoints. The default parameters are set as:
bInterval: 1 ms for FS and 8 uFrames (implying 1 ms) for HS/SS
wMaxPacketSize: 64 bytes for FS and 1024 bytes for HS/SS
However, the same can be overridden through the module parameter interface.
The code is tested for HS and SS on a platform having DWC3 controller.
Signed-off-by: Amit Virdi <amit.virdi@st.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
Richard Leitner [Thu, 21 Aug 2014 06:57:28 +0000 (08:57 +0200)]
usb: gadget: serial: remove PREFIX macro
Remove the ttyGS PREFIX macro from u_serial.c and replace all occurences with
the hardcoded ttyGS string.
This macro was mostly used in a few debug/warning messages and a lot of
hardcoded ttyGS existed beneath. It may have been used for renaming the
tty, but if done so most debug messages would have ignored this.
Due to the fact the usage of this PREFIX in all debug calls would have
resulted in a hard to read/grep code it is removed completely.
Signed-off-by: Richard Leitner <richard.leitner@skidata.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
usb: phy: msm: Make phy_reset clk and reset line optional.
This patch makes the phy reset clk and reset line optional as this clk
is not available on boards like IFC6410 with APQ8064.
phy-reset clk is only used as argument to the mach level callbacks, so
this patch adds condition before clk_get calls so that the driver
wouldn't fail on SOCs which do not have this support.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Signed-off-by: Felipe Balbi <balbi@ti.com>
Paul Zimmerman [Thu, 21 Aug 2014 20:28:20 +0000 (20:28 +0000)]
usb: gadget: document a usb_ep_dequeue() requirement
Document the requirement that the request be dequeued and its
completion routine called before usb_ep_dequeue() returns. Also
fix some capitalization issues in the existing text.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Felipe Balbi <balbi@ti.com>
If uvc->control_buf is successfuly allocated but uvc->control_req
is not, uvc->control_buf is not freed in the error recovery path.
With this patch applied uvc->control_buf is freed unconditionally;
if it happens to be NULL kfree on it is safe anyway.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com> Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
Philipp Zabel [Thu, 21 Aug 2014 14:54:44 +0000 (16:54 +0200)]
usb: gadget: uvc: Add support for DMABUF importing
Activate the videobuf2 DMABUF support. As vb2-vmalloc supports the
importer role only, exporting buffers isn't supported yet. When the
exporter role will be implemented in vb2-vmalloc the UVC gadget driver
will automatically gain support for it.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
usb: gadget: uvc: Change KERN_INFO to KERN_DEBUG on request shutdown
The disconnect of the USB Device is a common pattern for
an UVC Camera. In many cases this will give us an meaningless
information for all buffers that couldn't be enqueued.
That patch changes this to KERN_DEBUG.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de> Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
Add support for using f_uac1 function as a component of a gadget
composed with configfs.
Tested-by: Sebastian Reimers <sebastian.reimers@googlemail.com> Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
usb: gadget: f_uac1: use defined constants as defaults
When configfs support is added the values in question will have to be
used in two different places. Substitute them with defined constants
to avoid duplicating magic numbers.
Tested-by: Sebastian Reimers <sebastian.reimers@googlemail.com> Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
Tested-by: Sebastian Reimers <sebastian.reimers@googlemail.com> Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
There are no users of the old interface left, so it can be removed.
Tested-by: Sebastian Reimers <sebastian.reimers@googlemail.com> Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
usb: gadget: audio: convert to new interface of f_uac1
Use the new interface so that the old one can be removed.
Tested-by: Sebastian Reimers <sebastian.reimers@googlemail.com> Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
usb: gadget: f_uac1: convert to new function interface with backward compatibility
Converting uac1 to the new function interface requires converting
the USB uac1's function code and its users.
This patch converts the f_uac1.c to the new function interface.
The file is now compiled into a separate usb_f_uac1.ko module.
The old function interface is provided by means of a preprocessor
conditional directives. After all users are converted, the old interface
can be removed.
Tested-by: Sebastian Reimers <sebastian.reimers@googlemail.com> Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
usb: gadget: f_uac1: prepare for separate compilation
Integrating configfs requires converting f_uac1 to new function interface,
which in turn requires converting it to the new function interface,
which involves separate compilation of f_uac1.c into usb_f_uac1.ko.
u_uac1.c contains some module parameters. After this patch is applied
they are still a part of the resulting g_audio.ko, but can be guarded
with a compatiblity flag which will be removed when no users of the old
function interface of f_uac1 are left.
Tested-by: Sebastian Reimers <sebastian.reimers@googlemail.com> Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
Tested-by: Sebastian Reimers <sebastian.reimers@googlemail.com> Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
Add support for using f_uac2 function as a component of a gadget
composed with configfs.
Tested-by: Sebastian Reimers <sebastian.reimers@googlemail.com> Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
usb: gadget: f_uac2: use defined constants as defaults
When configfs is integrated the same values will have to be used
as defaults. Use symbolic names in order not to duplicate magic numbers.
Tested-by: Sebastian Reimers <sebastian.reimers@googlemail.com> Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
Tested-by: Sebastian Reimers <sebastian.reimers@googlemail.com> Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
There are no users of the old interface left, so it can be removed.
Tested-by: Sebastian Reimers <sebastian.reimers@googlemail.com> Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
usb: gadget: audio: convert to new interface of f_uac2
Use the new interface so that the old one can be removed.
Tested-by: Sebastian Reimers <sebastian.reimers@googlemail.com> Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
usb: gadget: f_uac2: convert to new function interface with backward compatibility
Converting uac2 to the new function interface requires converting
the USB uac2's function code and its users.
This patch converts the f_uac2.c to the new function interface.
The file is now compiled into a separate usb_f_uac2.ko module.
The old function interface is provided by means of a preprocessor
conditional directives. After all users are converted, the old interface
can be removed.
Tested-by: Sebastian Reimers <sebastian.reimers@googlemail.com> Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
usb: gadget: audio: Use container_of to free audio_dev
Eliminate static struct *agdev_g from f_uac2.c.
It is used for freeing its memory, but the same address can be found
by calling container_of in afunc_unbind(). This implies eliminating
uac2_unbind_config(). The audio_config_driver in audio.c does not have
its unbind method any more. It has been used only when uac2 is used,
so uac2 itself can handle unbinding in afunc_unbind().
Tested-by: Sebastian Reimers <sebastian.reimers@googlemail.com> Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
Jingoo Han [Mon, 4 Aug 2014 01:44:31 +0000 (10:44 +0900)]
usb: phy: samsung: Remove unnecessary lines of register bit definitions
Remove unnecessary lines of register bit definitions in order
to enhance the readability. In this case, there are lines
per register offset definitions. There is no functional change.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
Linus Torvalds [Sat, 16 Aug 2014 15:32:27 +0000 (09:32 -0600)]
Merge branch 'for_linus' of git://cavan.codon.org.uk/platform-drivers-x86
Pull x86 platform driver updates from Matthew Garrett:
"A moderate number of changes, but nothing awfully significant.
A lot of const cleanups, some reworking and additions to the rfkill
quirks in the asus driver, a new driver for generating falling laptop
events on Toshibas and some misc fixes.
Maybe vendors have stopped inventing things"
* 'for_linus' of git://cavan.codon.org.uk/platform-drivers-x86: (41 commits)
platform/x86: Enable build support for toshiba_haps
Documentation: Add file about toshiba_haps module
platform/x86: Toshiba HDD Active Protection Sensor
asus-nb-wmi: Add wapf4 quirk for the U32U
alienware-wmi: make hdmi_mux enabled on case-by-case basis
ideapad-laptop: Constify DMI table and other r/o variables
asus-nb-wmi.c: Rename x401u quirk to wapf4
compal-laptop: correct invalid hwmon name
toshiba_acpi: Add Qosmio X75-A to the alt keymap dmi list
toshiba_acpi: Add extra check to backlight code
Fix log message about future removal of interface
ideapad-laptop: Disable touchpad interface on Yoga models
asus-nb-wmi: Add wapf4 quirk for the X550CC
intel_ips: Make ips_mcp_limits variables static
thinkpad_acpi: Mark volume_alsa_control_{vol,mute} as __initdata
fujitsu-laptop: Mark fujitsu_dmi_table[] DMI table as __initconst
hp-wmi: Add missing __init annotations to initialization code
hp_accel: Constify ACPI and DMI tables
fujitsu-tablet: Mark DMI callbacks as __init code
dell-laptop: Mark dell_quirks[] DMI table as __initconst
...
Linus Torvalds [Sat, 16 Aug 2014 15:25:34 +0000 (09:25 -0600)]
Merge branch 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux
Pull idle update from Len Brown:
"Two Intel-platform-specific updates to intel_idle, and a cosmetic
tweak to the turbostat utility"
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
tools/power turbostat: tweak whitespace in output format
intel_idle: Broadwell support
intel_idle: Disable Baytrail Core and Module C6 auto-demotion
Linus Torvalds [Sat, 16 Aug 2014 15:24:41 +0000 (09:24 -0600)]
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull module fix from Rusty Russell:
"Nasty potential bug if someone uses a known module param with an
invalid value (we don't fail unknown module params any more, just
warn)"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
module: Clean up ro/nx after early module load failures
Linus Torvalds [Sat, 16 Aug 2014 15:06:55 +0000 (09:06 -0600)]
Merge branch 'for-linus2' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs updates from Chris Mason:
"These are all fixes I'd like to get out to a broader audience.
The biggest of the bunch is Mark's quota fix, which is also in the
SUSE kernel, and makes our subvolume quotas dramatically more
accurate.
I've been running xfstests with these against your current git
overnight, but I'm queueing up longer tests as well"
* 'for-linus2' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
btrfs: disable strict file flushes for renames and truncates
Btrfs: fix csum tree corruption, duplicate and outdated checksums
Btrfs: Fix memory corruption by ulist_add_merge() on 32bit arch
Btrfs: fix compressed write corruption on enospc
btrfs: correctly handle return from ulist_add
btrfs: qgroup: account shared subtrees during snapshot delete
Btrfs: read lock extent buffer while walking backrefs
Btrfs: __btrfs_mod_ref should always use no_quota
btrfs: adjust statfs calculations according to raid profiles
Linus Torvalds [Sat, 16 Aug 2014 14:58:47 +0000 (08:58 -0600)]
Merge tag 'locks-v3.17-2' of git://git.samba.org/jlayton/linux
Pull file locking bugfixes from Jeff Layton:
"Most of these patches are to fix a long-standing regression that crept
in when the BKL was removed from the file-locking code. The code was
converted to use a conventional spinlock, but some fl_release_private
ops can block and you can end up sleeping inside the lock.
There's also a patch to make /proc/locks show delegations as 'DELEG'"
* tag 'locks-v3.17-2' of git://git.samba.org/jlayton/linux:
locks: update Locking documentation to clarify fl_release_private behavior
locks: move locks_free_lock calls in do_fcntl_add_lease outside spinlock
locks: defer freeing locks in locks_delete_lock until after i_lock has been dropped
locks: don't reuse file_lock in __posix_lock_file
locks: don't call locks_release_private from locks_copy_lock
locks: show delegations as "DELEG" in /proc/locks
Linus Torvalds [Sat, 16 Aug 2014 14:56:27 +0000 (08:56 -0600)]
Merge git://git.kvack.org/~bcrl/aio-next
Pull aio updates from Ben LaHaise.
* git://git.kvack.org/~bcrl/aio-next:
aio: use iovec array rather than the single one
aio: fix some comments
aio: use the macro rather than the inline magic number
aio: remove the needless registration of ring file's private_data
aio: remove no longer needed preempt_disable()
aio: kill the misleading rcu read locks in ioctx_add_table() and kill_ioctx()
aio: change exit_aio() to load mm->ioctx_table once and avoid rcu_read_lock()
Azael Avalos [Thu, 14 Aug 2014 15:55:38 +0000 (09:55 -0600)]
platform/x86: Toshiba HDD Active Protection Sensor
This driver adds support for the built-in accelereometer found
on recent Toshiba laptops with HID TOS620A.
This driver receives ACPI notify events 0x80 when the sensor
detects a sudden move or a harsh vibration, as well as an
ACPI notify event 0x81 whenever the movement or vibration has
been stabilized.
Also provides sysfs entries to get/set the desired protection
level and reseting the HDD protection interface.
Signed-off-by: Azael Avalos <coproscefalo@gmail.com> Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
ideapad-laptop: Constify DMI table and other r/o variables
Constify the rfkill_blacklist[] DMI table, the ideapad_rfk_data[] table
and the ideapad_attribute_group attribute group. There's no need to have
them writeable during runtime.
Signed-off-by: Mathias Krause <minipli@googlemail.com> Cc: Ike Panhc <ike.pan@canonical.com> Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
Hans de Goede [Mon, 14 Jul 2014 07:14:34 +0000 (09:14 +0200)]
asus-nb-wmi.c: Rename x401u quirk to wapf4
The actual x401u does not use the so named x401u quirk but the x55u quirk.
All that the x401u quirk does it setting wapf to 4, so rename it to wapf4 to
stop the confusion.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
Roald Frederickx [Wed, 13 Aug 2014 20:40:14 +0000 (13:40 -0700)]
compal-laptop: correct invalid hwmon name
Change the name of the hwmon interface from "compal-laptop" to "compal".
A dash is an invalid character for a hwmon name and caused the call to
hwmon_device_register_with_groups() to fail.
Signed-off-by: Roald Frederickx <roald.frederickx@gmail.com> Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
Azael Avalos [Mon, 4 Aug 2014 15:21:01 +0000 (09:21 -0600)]
toshiba_acpi: Add extra check to backlight code
Some Toshiba models (most notably Qosmios) come with an
incomplete backlight method where the AML code doesn't
check for write or read commands and always returns
HCI_SUCCESS and the actual brightness (and in some
cases the max brightness), thus allowing the backlight
interface to be registered without write support.
This patch changes the set_lcd_brightness function,
checking the returned values for values greater than
zero to avoid registering a broken backlight interface.
Signed-off-by: Azael Avalos <coproscefalo@gmail.com> Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
thinkpad_acpi: Mark volume_alsa_control_{vol,mute} as __initdata
Mark volume_alsa_control_vol and volume_alsa_control_mute as __initdata,
as snd_ctl_new1() will copy the relevant parts, so there is no need to
keep the master copies around after initialization.
Signed-off-by: Mathias Krause <minipli@googlemail.com> Cc: Henrique de Moraes Holschuh <ibm-acpi@hmh.eng.br> Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
fujitsu-laptop: Mark fujitsu_dmi_table[] DMI table as __initconst
The DMI table is only ever used during initialization. Mark it as
__initconst so its memory can be released afterwards -- roughly 1.5 kB.
In turn, the callback functions can be marked with __init, too.
Signed-off-by: Mathias Krause <minipli@googlemail.com> Cc: Jonathan Woithe <jwoithe@just42.net> Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
dell-laptop: Mark dell_quirks[] DMI table as __initconst
The dell_quirks[] DMI table is only ever used during initialization.
Mark it as __initconst so its memory can be released afterwards --
roughly 5.7 kB. In turn, the callback function can be marked with
__init, too.
Also the touchpad_led_init() function can be marked __init as it's only
referenced from dell_init() -- an __init function.
Signed-off-by: Mathias Krause <minipli@googlemail.com> Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
Quite a lot of code and data of acer-wmi.c is only ever used during
initialization. Mark those accordingly -- and constify, where
appropriate -- so the memory can be released afterwards.
All in all those changes move ~10 kB of code and data to the .init
sections, marking them for release after initialization has finished.
The DMI table is only ever used during initialization. Mark it as
__initconst so its memory can be released appropriately. In turn, the
callback function can be marked with __init, too.
Signed-off-by: Mathias Krause <minipli@googlemail.com> Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
acer-wmi: Hide acer_{suspend,resume} for !CONFIG_PM_SLEEP
Encapsulate acer_suspend() and acer_resume with #ifdef CONFIG_PM_SLEEP
to get rid of the following warnings:
../acer-wmi.c:2046:12: warning: ‘acer_suspend’ defined but not used [-Wunused-function]
../acer-wmi.c:2068:12: warning: ‘acer_resume’ defined but not used [-Wunused-function]
This patch removes the null test on block. block is initialized at the
beginning of the function to &wblock->gblock. Since wblock is
dereferenced prior to the null test, wblock must be a valid pointer,
and &wblock->gblock cannot be null.
The following Coccinelle script is used for detecting the change:
AceLan Kao [Wed, 9 Jul 2014 08:18:19 +0000 (16:18 +0800)]
asus-nb-wmi: Add ASUSTeK COMPUTER INC. X200CA
BIOS won't light on the wifi-led after S3, so asus-wmi driver needs to
control the wifi and wifi-led status.
But, it'll lead to bt status error if asus-wmi driver controls bt as well.
So, for X200CA, asus-wmi driver controls wifi status only and have to set
wapf to 1.
Signed-off-by: AceLan Kao <acelan.kao@canonical.com> Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
Hans de Goede [Tue, 8 Jul 2014 08:47:22 +0000 (10:47 +0200)]
asus-wmi: backlight_init: Stop treating -ENODEV as if its not an error
When bl_power support got added to asus-wmi, the error handling for it was
written to ignore -ENODEV, to avoid not registering a backlight interface for
models which have no bl_power control, but do have brightness control.
At the same time the error handling for brightness_max was modified to do the
same, this is wrong, when there is no brightness_max asus-wmi should not
register a backlight interface.
Note the caller of asus_wmi_backlight_init already special cases -ENODEV,
and will not cause the wmi driver regristration to fail because of a
-ENODEV return from asus_wmi_backlight_init.
Hans de Goede [Tue, 8 Jul 2014 08:47:21 +0000 (10:47 +0200)]
asus-wmi: Disable acpi-video backlight on desktop machines
Some Asus motherboards for desktop PC-s export an acpi-video interface
advertising backlight support. Test the dmi chassis-type and tell acpi-video
to not register a backlight interface on desktops.
projects / linux-beck.git / log