Marcin Wojtas [Mon, 30 Nov 2015 12:27:44 +0000 (13:27 +0100)]
net: mvneta: fix error path for building skb
In the actual RX processing, there is same error path for both descriptor
ring refilling and building skb fails. This is not correct, because after
successful refill, the ring is already updated with newly allocated
buffer. Then, in case of build_skb() fail, hitherto code left the original
buffer unmapped.
This patch fixes above situation by swapping error check of skb build with
DMA-unmap of original buffer.
Signed-off-by: Marcin Wojtas <mw@semihalf.com> Acked-by: Simon Guinot <simon.guinot@sequanux.org> Cc: <stable@vger.kernel.org> # v4.2+
Fixes a84e32894191 ("net: mvneta: fix refilling for Rx DMA buffers") Signed-off-by: David S. Miller <davem@davemloft.net>
Marcin Wojtas [Mon, 30 Nov 2015 12:27:43 +0000 (13:27 +0100)]
net: mvneta: fix bit assignment for RX packet irq enable
A value originally defined in the driver was inappropriate. Even though
the ingress was somehow working, writing MVNETA_RXQ_INTR_ENABLE_ALL_MASK
to MVNETA_INTR_ENABLE didn't make any effect, because the bits [31:16]
are reserved and read-only.
This commit updates MVNETA_RXQ_INTR_ENABLE_ALL_MASK to be compliant with
the controller's documentation.
Signed-off-by: Marcin Wojtas <mw@semihalf.com> Fixes: c5aff18204da ("net: mvneta: driver for Marvell Armada 370/XP network
unit") Signed-off-by: David S. Miller <davem@davemloft.net>
Marcin Wojtas [Mon, 30 Nov 2015 12:27:42 +0000 (13:27 +0100)]
net: mvneta: fix bit assignment in MVNETA_RXQ_CONFIG_REG
MVNETA_RXQ_HW_BUF_ALLOC bit which controls enabling hardware buffer
allocation was mistakenly set as BIT(1). This commit fixes the assignment.
Signed-off-by: Marcin Wojtas <mw@semihalf.com> Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Fixes: c5aff18204da ("net: mvneta: driver for Marvell Armada 370/XP network
unit") Signed-off-by: David S. Miller <davem@davemloft.net>
Marcin Wojtas [Mon, 30 Nov 2015 12:27:41 +0000 (13:27 +0100)]
net: mvneta: add configuration for MBUS windows access protection
This commit adds missing configuration of MBUS windows access protection
in mvneta_conf_mbus_windows function - a dedicated variable for that
purpose remained there unused since v3.8 initial mvneta support. Because
of that the register contents were inherited from the bootloader.
Signed-off-by: Marcin Wojtas <mw@semihalf.com> Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Fixes: c5aff18204da ("net: mvneta: driver for Marvell Armada 370/XP network
unit") Signed-off-by: David S. Miller <davem@davemloft.net>
This patch series contains fixes for various issues observed
with BGX and NIC drivers.
Changes from v1:
- Fixed comment syle in the first patch of the series
- Removed 'Increase transmit queue length' patch from the series,
will recheck if it's a driver or system issue and resubmit.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Sunil Goutham [Wed, 2 Dec 2015 10:06:17 +0000 (15:36 +0530)]
net: thunderx: Enable BGX LMAC's RX/TX only after VF is up
Enable or disable BGX LMAC's RX/TX based on corresponding VF's
status. If otherwise, when multiple LMAC's physical link is up
then packets from all LMAC's whose corresponding VF is not yet
initialized will get forwarded to VF0. This is due to VNIC's default
configuration where CPI, RSSI e.t.c point to VF0/QSET0/RQ0.
This patch will prevent multiple copies of packets on VF0.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sunil Goutham [Wed, 2 Dec 2015 10:06:16 +0000 (15:36 +0530)]
net: thunderx: Switchon carrier only upon interface link up
Call netif_carrier_on() only if interface's link is up. Switching this on
upon IFF_UP by default, is causing issues with ethernet channel bonding
in LACP mode. Initial NETDEV_CHANGE notification was being skipped.
Also fixed some issues with link/speed/duplex reporting via ethtool.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: thunderx: Wait for delayed work to finish before destroying it
While VNIC or BGX driver teardown, wait for already scheduled delayed work to
finish before destroying it.
Signed-off-by: Thanneeru Srinivasulu <tsrinivasulu@caviumnetworks.com> Signed-off-by: Sunil Goutham <sgoutham@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: thunderx: Force to load octeon-mdio before bgx driver.
Signed-off-by: Thanneeru Srinivasulu <tsrinivasulu@caviumnetworks.com> Signed-off-by: Sunil Goutham <sgoutham@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Mon, 30 Nov 2015 11:31:43 +0000 (12:31 +0100)]
openvswitch: properly refcount vport-vxlan module
After 614732eaa12d, no refcount is maintained for the vport-vxlan module.
This allows the userspace to remove such module while vport-vxlan
devices still exist, which leads to later oops.
v1 -> v2:
- move vport 'owner' initialization in ovs_vport_ops_register()
and make such function a macro
Fixes: 614732eaa12d ("openvswitch: Use regular VXLAN net_device device") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Mon, 30 Nov 2015 12:02:56 +0000 (13:02 +0100)]
bpf, array: fix heap out-of-bounds access when updating elements
During own review but also reported by Dmitry's syzkaller [1] it has been
noticed that we trigger a heap out-of-bounds access on eBPF array maps
when updating elements. This happens with each map whose map->value_size
(specified during map creation time) is not multiple of 8 bytes.
In array_map_alloc(), elem_size is round_up(attr->value_size, 8) and
used to align array map slots for faster access. However, in function
array_map_update_elem(), we update the element as ...
... where we access 'value' out-of-bounds, since it was allocated from
map_update_elem() from syscall side as kmalloc(map->value_size, GFP_USER)
and later on copied through copy_from_user(value, uvalue, map->value_size).
Thus, up to 7 bytes, we can access out-of-bounds.
Same could happen from within an eBPF program, where in worst case we
access beyond an eBPF program's designated stack.
Since 1be7f75d1668 ("bpf: enable non-root eBPF programs") didn't hit an
official release yet, it only affects priviledged users.
In case of array_map_lookup_elem(), the verifier prevents eBPF programs
from accessing beyond map->value_size through check_map_access(). Also
from syscall side map_lookup_elem() only copies map->value_size back to
user, so nothing could leak.
[1] http://github.com/google/syzkaller
Fixes: 28fbcfa08d8e ("bpf: add array type of eBPF maps") Reported-by: Dmitry Vyukov <dvyukov@google.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 30 Nov 2015 04:03:11 +0000 (20:03 -0800)]
net: fix sock_wake_async() rcu protection
Dmitry provided a syzkaller (http://github.com/google/syzkaller)
triggering a fault in sock_wake_async() when async IO is requested.
Said program stressed af_unix sockets, but the issue is generic
and should be addressed in core networking stack.
The problem is that by the time sock_wake_async() is called,
we should not access the @flags field of 'struct socket',
as the inode containing this socket might be freed without
further notice, and without RCU grace period.
We already maintain an RCU protected structure, "struct socket_wq"
so moving SOCKWQ_ASYNC_NOSPACE & SOCKWQ_ASYNC_WAITDATA into it
is the safe route.
It also reduces number of cache lines needing dirtying, so might
provide a performance improvement anyway.
In followup patches, we might move remaining flags (SOCK_NOSPACE,
SOCK_PASSCRED, SOCK_PASSSEC) to save 8 bytes and let 'struct socket'
being mostly read and let it being shared between cpus.
Reported-by: Dmitry Vyukov <dvyukov@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 30 Nov 2015 04:03:10 +0000 (20:03 -0800)]
net: rename SOCK_ASYNC_NOSPACE and SOCK_ASYNC_WAITDATA
This patch is a cleanup to make following patch easier to
review.
Goal is to move SOCK_ASYNC_NOSPACE and SOCK_ASYNC_WAITDATA
from (struct socket)->flags to a (struct socket_wq)->flags
to benefit from RCU protection in sock_wake_async()
To ease backports, we rename both constants.
Two new helpers, sk_set_bit(int nr, struct sock *sk)
and sk_clear_bit(int net, struct sock *sk) are added so that
following patch can change their implementation.
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
vmxnet3_drv does not check dma_addr with dma_mapping_error()
after mapping dma memory. The patch adds the checks and
tries to handle failures.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru> Acked-by: Shrikrishna Khare <skhare@vmware.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Peter Hurley [Fri, 27 Nov 2015 19:18:39 +0000 (14:18 -0500)]
wan/x25: Fix use-after-free in x25_asy_open_tty()
The N_X25 line discipline may access the previous line discipline's closed
and already-freed private data on open [1].
The tty->disc_data field _never_ refers to valid data on entry to the
line discipline's open() method. Rather, the ldisc is expected to
initialize that field for its own use for the lifetime of the instance
(ie. from open() to close() only).
Reported-and-tested-by: Sasha Levin <sasha.levin@oracle.com> Cc: <stable@vger.kernel.org> Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: David S. Miller <davem@davemloft.net>
In IPv6, we cannot inherit the dst of the original dst. ndisc packets
are IPv6 packets and may take another route than the original packet.
This patch breaks the following scenario: a packet comes from eth0 and
is forwarded through vxlan1. The encapsulated packet triggers an NS
which cannot be sent because of the wrong route.
CC: Jiri Benc <jbenc@redhat.com> CC: Thomas Graf <tgraf@suug.ch> Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net>
His program is specifically attempting a Cross SYN TCP exchange,
that we support (for the pleasure of hackers ?), but it looks we
lack proper tcp->copied_seq initialization.
Thanks again Dmitry for your report and testings.
Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Dmitry Vyukov <dvyukov@google.com> Tested-by: Dmitry Vyukov <dvyukov@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Mark Brown [Thu, 26 Nov 2015 11:59:46 +0000 (11:59 +0000)]
net: fsl: Fix error checking for platform_get_irq()
The gianfar driver has recently been enabled on arm64 but fails to build
since it check the return value of platform_get_irq() against NO_IRQ. Fix
this by instead checking for a negative error code.
Even on ARM where this code was previously being built this check was
incorrect since platform_get_irq() returns a negative error code which
may not be exactly the (unsigned int)(-1) that NO_IRQ is defined to be.
Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Mark Brown [Thu, 26 Nov 2015 11:59:45 +0000 (11:59 +0000)]
net: fsl: Don't use NO_IRQ to check return value of irq_of_parse_and_map()
This driver can be built on arm64 but relies on NO_IRQ to check the return
value of irq_of_parse_and_map() which fails to build on arm64 because the
architecture does not provide a NO_IRQ. Fix this to correctly check the
return value of irq_of_parse_and_map().
Even on ARM systems where the driver was previously used the check was
broken since on ARM NO_IRQ is -1 but irq_of_parse_and_map() returns 0 on
error.
Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
sendpage did not care about credentials at all. This could lead to
situations in which because of fd passing between processes we could
append data to skbs with different scm data. It is illegal to splice those
skbs together. Instead we have to allocate a new skb and if requested
fill out the scm details.
Fixes: 869e7c62486ec ("net: af_unix: implement stream sendpage support") Reported-by: Al Viro <viro@zeniv.linux.org.uk> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Eric Dumazet <edumazet@google.com> Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 30 Nov 2015 19:52:52 +0000 (14:52 -0500)]
Merge branch 'stmmac-fixes'
Giuseppe Cavallaro says:
====================
Spare stmmac fixes
These are some fixes for the stmmac d.d. tested on STi platforms.
They are for some part of the PM, STi glue and rx path when test
Jumbo.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The receive skb buffers can be preallocated when the link is opened
according to mtu size.
While testing on a network environment with not standard MTU (e.g. 3000),
a panic occurred if an incoming packet had a length greater than rx skb
buffer size. This is because the HW is programmed to copy, from the DMA,
an Jumbo frame and the Sw must check if the allocated buffer is enough to
store the frame.
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com> Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
When stmmac_mdio_reset, was called from stmmac_resume, it was not
resetting the PHY due to which MAC was not getting reset properly and
hence ethernet interface not was resumed properly.
The issue was currently only reproducible on stih301-b2204.
Signed-off-by: Pankaj Dev <pankaj.dev@st.com> Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
In case of the st,tx-retime-src is missing from device-tree
(it's an optional field) the driver will invoke the strcasecmp to check
which clock has been selected and this is a bug; the else condition
is needed.
In the dwmac_setup, the "rs" variable, passed to the strcasecmp, was not
initialized and the compiler, depending on the options adopted, could
take it in some different part of the stack generating the hang in such
configuration.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to fix the csr clock in case of 300MHz is provided.
Reported-by: Kent Borg <Kent.Borg@csr.com> Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
When resume the HW is re-configured but some settings can be lost.
For example, the MAC Address_X High/Low Registers used for VLAN tagging..
So, while resuming, the set_filter callback needs to be invoked to
re-program perfect and hash-table registers.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 25 Nov 2015 17:02:10 +0000 (09:02 -0800)]
drivers: net: xgene: fix possible use after free
Once TX has been enabled on a NIC, it is illegal to access skb,
as this skb might have been freed by another cpu, from TX completion
handler.
Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Mark Rutland <mark.rutland@arm.com> Tested-by: Mark Rutland <mark.rutland@arm.com> Cc: Iyappan Subramanian <isubramanian@apm.com> Acked-by: Iyappan Subramanian <isubramanian@apm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
packet: Allow packets with only a header (but no payload)
Commit 9c7077622dd91 ("packet: make packet_snd fail on len smaller
than l2 header") added validation for the packet size in packet_snd.
This change enforces that every packet needs a header (with at least
hard_header_len bytes) plus a payload with at least one byte. Before
this change the payload was optional.
This fixes PPPoE connections which do not have a "Service" or
"Host-Uniq" configured (which is violating the spec, but is still
widely used in real-world setups). Those are currently failing with the
following message: "pppd: packet size is too short (24 <= 24)"
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Tue, 24 Nov 2015 20:28:15 +0000 (21:28 +0100)]
bpf: fix clearing on persistent program array maps
Currently, when having map file descriptors pointing to program arrays,
there's still the issue that we unconditionally flush program array
contents via bpf_fd_array_map_clear() in bpf_map_release(). This happens
when such a file descriptor is released and is independent of the map's
refcount.
Having this flush independent of the refcount is for a reason: there
can be arbitrary complex dependency chains among tail calls, also circular
ones (direct or indirect, nesting limit determined during runtime), and
we need to make sure that the map drops all references to eBPF programs
it holds, so that the map's refcount can eventually drop to zero and
initiate its freeing. Btw, a walk of the whole dependency graph would
not be possible for various reasons, one being complexity and another
one inconsistency, i.e. new programs can be added to parts of the graph
at any time, so there's no guaranteed consistent state for the time of
such a walk.
Now, the program array pinning itself works, but the issue is that each
derived file descriptor on close would nevertheless call unconditionally
into bpf_fd_array_map_clear(). Instead, keep track of users and postpone
this flush until the last reference to a user is dropped. As this only
concerns a subset of references (f.e. a prog array could hold a program
that itself has reference on the prog array holding it, etc), we need to
track them separately.
Short analysis on the refcounting: on map creation time usercnt will be
one, so there's no change in behaviour for bpf_map_release(), if unpinned.
If we already fail in map_create(), we are immediately freed, and no
file descriptor has been made public yet. In bpf_obj_pin_user(), we need
to probe for a possible map in bpf_fd_probe_obj() already with a usercnt
reference, so before we drop the reference on the fd with fdput().
Therefore, if actual pinning fails, we need to drop that reference again
in bpf_any_put(), otherwise we keep holding it. When last reference
drops on the inode, the bpf_any_put() in bpf_evict_inode() will take
care of dropping the usercnt again. In the bpf_obj_get_user() case, the
bpf_any_get() will grab a reference on the usercnt, still at a time when
we have the reference on the path. Should we later on fail to grab a new
file descriptor, bpf_any_put() will drop it, otherwise we hold it until
bpf_map_release() time.
Joint work with Alexei.
Fixes: b2197755b263 ("bpf: add support for persistent maps/progs") Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Christoph Biedl [Wed, 25 Nov 2015 06:47:40 +0000 (07:47 +0100)]
isdn: Partially revert debug format string usage clean up
Commit 35a4a57 ("isdn: clean up debug format string usage") introduced
a safeguard to avoid accidential format string interpolation of data
when calling debugl1 or HiSax_putstatus. This did however not take into
account VHiSax_putstatus (called by HiSax_putstatus) does *not* call
vsprintf if the head parameter is NULL - the format string is treated
as plain text then instead. As a result, the string "%s" is processed
literally, and the actual information is lost. This affects the isdnlog
userspace program which stopped logging information since that commit.
So revert the HiSax_putstatus invocations to the previous state.
Fixes: 35a4a5733b0a ("isdn: clean up debug format string usage") Cc: Kees Cook <keescook@chromium.org> Cc: Karsten Keil <isdn@linux-pingi.de> Signed-off-by: Christoph Biedl <linux-kernel.bfrz@manchmal.in-ulm.de> Signed-off-by: David S. Miller <davem@davemloft.net>
RDS: fix race condition when sending a message on unbound socket
Sasha's found a NULL pointer dereference in the RDS connection code when
sending a message to an apparently unbound socket. The problem is caused
by the code checking if the socket is bound in rds_sendmsg(), which checks
the rs_bound_addr field without taking a lock on the socket. This opens a
race where rs_bound_addr is temporarily set but where the transport is not
in rds_bind(), leading to a NULL pointer dereference when trying to
dereference 'trans' in __rds_conn_create().
Vegard wrote a reproducer for this issue, so kindly ask him to share if
you're interested.
I cannot reproduce the NULL pointer dereference using Vegard's reproducer
with this patch, whereas I could without.
Complete earlier incomplete fix to CVE-2015-6937:
74e98eb08588 ("RDS: verify the underlying transport exists before creating a connection")
Cc: David S. Miller <davem@davemloft.net> Cc: stable@vger.kernel.org Reviewed-by: Vegard Nossum <vegard.nossum@oracle.com> Reviewed-by: Sasha Levin <sasha.levin@oracle.com> Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by: Quentin Casasnovas <quentin.casasnovas@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Aaron Conole [Tue, 24 Nov 2015 18:51:53 +0000 (13:51 -0500)]
net: openvswitch: Remove invalid comment
During pre-upstream development, the openvswitch datapath used a custom
hashtable to store vports that could fail on delete due to lack of
memory. However, prior to upstream submission, this code was reworked to
use an hlist based hastable with flexible-array based buckets. As such
the failure condition was eliminated from the vport_del path, rendering
this comment invalid.
Signed-off-by: Aaron Conole <aconole@bytheb.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Since (at least) commit b17a7c179dd3 ("[NET]: Do sysfs registration as
part of register_netdevice."), netdev_run_todo() deals only with
unregistration, so we don't need to do the rtnl_unlock/lock cycle to
finish registration when failing pimreg or dvmrp device creation. In
fact that opens a race condition where someone can delete the device
while rtnl is unlocked because it's fully registered. The problem gets
worse when netlink support is introduced as there are more points of entry
that can cause it and it also makes reusing that code correctly impossible.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Reviewed-by: Cong Wang <cwang@twopensource.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Howells [Tue, 24 Nov 2015 14:41:59 +0000 (14:41 +0000)]
rxrpc: Correctly handle ack at end of client call transmit phase
Normally, the transmit phase of a client call is implicitly ack'd by the
reception of the first data packet of the response being received.
However, if a security negotiation happens, the transmit phase, if it is
entirely contained in a single packet, may get an ack packet in response
and then may get aborted due to security negotiation failure.
Because the client has shifted state to RXRPC_CALL_CLIENT_AWAIT_REPLY due
to having transmitted all the data, the code that handles processing of the
received ack packet doesn't note the hard ack the data packet.
The following abort packet in the case of security negotiation failure then
incurs an assertion failure when it tries to drain the Tx queue because the
hard ack state is out of sync (hard ack means the packets have been
processed and can be discarded by the sender; a soft ack means that the
packets are received but could still be discarded and rerequested by the
receiver).
To fix this, we should record the hard ack we received for the ack packet.
The assertion failure looks like:
RxRPC: Assertion failed
1 <= 0 is false
0x1 <= 0x0 is false
------------[ cut here ]------------
kernel BUG at ../net/rxrpc/ar-ack.c:431!
...
RIP: 0010:[<ffffffffa006857b>] [<ffffffffa006857b>] rxrpc_rotate_tx_window+0xbc/0x131 [af_rxrpc]
...
Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Kubeček [Tue, 24 Nov 2015 14:07:11 +0000 (15:07 +0100)]
ipv6: distinguish frag queues by device for multicast and link-local packets
If a fragmented multicast packet is received on an ethernet device which
has an active macvlan on top of it, each fragment is duplicated and
received both on the underlying device and the macvlan. If some
fragments for macvlan are processed before the whole packet for the
underlying device is reassembled, the "overlapping fragments" test in
ip6_frag_queue() discards the whole fragment queue.
To resolve this, add device ifindex to the search key and require it to
match reassembling multicast packets and packets to link-local
addresses.
Note: similar patch has been already submitted by Yoshifuji Hideaki in
http://patchwork.ozlabs.org/patch/220979/
but got lost and forgotten for some reason.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz> Signed-off-by: David S. Miller <davem@davemloft.net>
Bjørn Mork [Mon, 23 Nov 2015 13:32:10 +0000 (14:32 +0100)]
net: cdc_ncm: fix NULL pointer deref in cdc_ncm_bind_common
Commit 77b0a099674a ("cdc-ncm: use common parser") added a dangerous
new trust in the CDC functional descriptors presented by the device,
unconditionally assuming that any device handled by the driver has
a CDC Union descriptor.
This descriptor is required by the NCM and MBIM specs, but crashing
on non-compliant devices is still unacceptable. Not only will that
allow malicious devices to crash the kernel, but in this case it is
also well known that there are non-compliant real devices on the
market - as shown by the comment accompanying the IAD workaround
in the same function.
The Sierra Wireless EM7305 is an example of such device, having
a CDC header and a CDC MBIM descriptor but no CDC Union:
The conversion to a common parser also left the local cdc_union
variable untouched. This caused the IAD workaround code to be applied
to all devices with an IAD descriptor, which was never intended. Finish
the conversion by testing for hdr.usb_cdc_union_desc instead.
Cc: Oliver Neukum <oneukum@suse.com> Fixes: 77b0a099674a ("cdc-ncm: use common parser") Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 24 Nov 2015 19:21:45 +0000 (14:21 -0500)]
Merge tag 'linux-can-fixes-for-4.4-20151123' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2015-11-23
this is a pull request of three patches for the upcoming v4.4 release.
The first patch is by Mirza Krak, it fixes a problem with the sja1000 driver
after resuming from suspend to disk, by clearing all outstanding interrupts.
Oliver Hartkopp contributes two patches targeting almost all driver, they fix
the assignment of the error location in CAN error messages.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When expanding buffer headroom over udp tunnel with pskb_expand_head(),
it's unfortunate that we don't check its return value. As a result, if
the function returns an error code due to the lack of memory, it may
cause unpredictable consequence as we unconditionally consider that
it's always successful.
Fixes: e53567948f82 ("tipc: conditionally expand buffer headroom over udp tunnel") Reported-by: <scan-admin@coverity.com> Cc: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ying Xue [Sun, 22 Nov 2015 07:46:05 +0000 (15:46 +0800)]
tipc: avoid packets leaking on socket receive queue
Even if we drain receive queue thoroughly in tipc_release() after tipc
socket is removed from rhashtable, it is possible that some packets
are in flight because some CPU runs receiver and did rhashtable lookup
before we removed socket. They will achieve receive queue, but nobody
delete them at all. To avoid this leak, we register a private socket
destructor to purge receive queue, meaning releasing packets pending
on receive queue will be delayed until the last reference of tipc
socket will be released.
Signed-off-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Aaro Koskinen [Sat, 21 Nov 2015 23:08:54 +0000 (01:08 +0200)]
broadcom: fix PHY_ID_BCM5481 entry in the id table
Commit fcb26ec5b18d ("broadcom: move all PHY_ID's to header")
updated broadcom_tbl to use PHY_IDs, but incorrectly replaced 0x0143bca0
with PHY_ID_BCM5482 (making a duplicate entry, and completely omitting
the original). Fix that.
Fixes: fcb26ec5b18d ("broadcom: move all PHY_ID's to header") Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi> Signed-off-by: David S. Miller <davem@davemloft.net>
vrf: fix double free and memory corruption on register_netdevice failure
When vrf's ->newlink is called, if register_netdevice() fails then it
does free_netdev(), but that's also done by rtnl_newlink() so a second
free happens and memory gets corrupted, to reproduce execute the
following line a couple of times (1 - 5 usually is enough):
$ for i in `seq 1 5`; do ip link add vrf: type vrf table 1; done;
This works because we fail in register_netdevice() because of the wrong
name "vrf:".
Fixes: 193125dbd8eb ("net: Introduce VRF device driver") Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Acked-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Rainer Weikusat [Fri, 20 Nov 2015 22:07:23 +0000 (22:07 +0000)]
unix: avoid use-after-free in ep_remove_wait_queue
Rainer Weikusat <rweikusat@mobileactivedefense.com> writes:
An AF_UNIX datagram socket being the client in an n:1 association with
some server socket is only allowed to send messages to the server if the
receive queue of this socket contains at most sk_max_ack_backlog
datagrams. This implies that prospective writers might be forced to go
to sleep despite none of the message presently enqueued on the server
receive queue were sent by them. In order to ensure that these will be
woken up once space becomes again available, the present unix_dgram_poll
routine does a second sock_poll_wait call with the peer_wait wait queue
of the server socket as queue argument (unix_dgram_recvmsg does a wake
up on this queue after a datagram was received). This is inherently
problematic because the server socket is only guaranteed to remain alive
for as long as the client still holds a reference to it. In case the
connection is dissolved via connect or by the dead peer detection logic
in unix_dgram_sendmsg, the server socket may be freed despite "the
polling mechanism" (in particular, epoll) still has a pointer to the
corresponding peer_wait queue. There's no way to forcibly deregister a
wait queue with epoll.
Based on an idea by Jason Baron, the patch below changes the code such
that a wait_queue_t belonging to the client socket is enqueued on the
peer_wait queue of the server whenever the peer receive queue full
condition is detected by either a sendmsg or a poll. A wake up on the
peer queue is then relayed to the ordinary wait queue of the client
socket via wake function. The connection to the peer wait queue is again
dissolved if either a wake up is about to be relayed or the client
socket reconnects or a dead peer is detected or the client socket is
itself closed. This enables removing the second sock_poll_wait from
unix_dgram_poll, thus avoiding the use-after-free, while still ensuring
that no blocked writer sleeps forever.
Signed-off-by: Rainer Weikusat <rweikusat@mobileactivedefense.com> Fixes: ec0d215f9420 ("af_unix: fix 'poll for write'/connected DGRAM sockets") Reviewed-by: Jason Baron <jbaron@akamai.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Nina Schiff [Fri, 20 Nov 2015 20:31:39 +0000 (12:31 -0800)]
cgroups: Allow dynamically changing net_classid
The classid of a process is changed either when a process is moved to
or from a cgroup or when the net_cls.classid file is updated.
Previously net_cls only supported propogating these changes to the
cgroup's related sockets when a process was added or removed from the
cgroup. This means it was neccessary to remove and re-add all processes
to a cgroup in order to update its classid. This change introduces
support for doing this dynamically - i.e. when the value is changed in
the net_cls_classid file, this will also trigger an update to the
classid associated with all sockets controlled by the cgroup.
This mimics the behaviour of other cgroup subsystems.
net_prio circumvents this issue by storing an index into a table with
each socket (and so any updates to the table, don't require updating
the value associated with the socket). net_cls, however, passes the
socket the classid directly, and so this additional step is needed.
Signed-off-by: Nina Schiff <ninasc@fb.com> Acked-by: Tejun Heo <tj@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Shaohui Xie [Fri, 20 Nov 2015 03:54:08 +0000 (11:54 +0800)]
net: fsl: expands dependencies of NET_VENDOR_FREESCALE
Freescale hosts some ARMv8 based SoCs, and a generic convention
ARCH_LAYERSCAPE is used to cover such SoCs. Adding ARCH_LAYERSCAPE
to dependencies of NET_VENDOR_FREESCALE to support networking on those
SoCs.
The ARCH_LAYERSCAPE is introduced by:
commit: 53a5fde05 arm64: Use generic Layerscape SoC family naming
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Oliver Hartkopp [Sat, 21 Nov 2015 17:41:21 +0000 (18:41 +0100)]
can: remove obsolete assignment for CAN protocol error type
The assignment 'cf->data[2] |= CAN_ERR_PROT_UNSPEC' used at CAN error message
creation time is obsolete as CAN_ERR_PROT_UNSPEC is zero and cf->data[2] is
initialized with zero in alloc_can_err_skb() anyway.
So we could either assign 'cf->data[2] = CAN_ERR_PROT_UNSPEC' correctly or we
can remove the obsolete OR operation entirely.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Oliver Hartkopp [Sat, 21 Nov 2015 17:41:20 +0000 (18:41 +0100)]
can: fix assignment of error location in CAN error messages
As Dan Carpenter reported in http://marc.info/?l=linux-can&m=144793696016187
the assignment of the error location in CAN error messages had some bit wise
overlaps. Indeed the value to be assigned in data[3] is no bitfield but defines
a single value which points to a location inside the CAN frame on the wire.
This patch fixes the assignments for the error locations in error messages.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Mirza Krak [Tue, 10 Nov 2015 13:59:34 +0000 (14:59 +0100)]
can: sja1000: clear interrupts on start
According to SJA1000 data sheet error-warning (EI) interrupt is not
cleared by setting the controller in to reset-mode.
Then if we have the following case:
- system is suspended (echo mem > /sys/power/state) and SJA1000 is left
in operating state
- A bus error condition occurs which activates EI interrupt, system is
still suspended which means EI interrupt will be not be handled nor
cleared.
If the above two events occur, on resume there is no way to return the
SJA1000 to operating state, except to cycle power to it.
By simply reading the IR register on start we will clear any previous
conditions that could be present.
Signed-off-by: Mirza Krak <mirza.krak@hostmobility.com> Reported-by: Christian Magnusson <Christian.Magnusson@semcon.com> Cc: linux-stable <stable@vger.kernel.org> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
net: ip6mr: fix static mfc/dev leaks on table destruction
Similar to ipv4, when destroying an mrt table the static mfc entries and
the static devices are kept, which leads to devices that can never be
destroyed (because of refcnt taken) and leaked memory. Make sure that
everything is cleaned up on netns destruction.
Fixes: 8229efdaef1e ("netns: ip6mr: enable namespace support in ipv6 multicast forwarding code") CC: Benjamin Thery <benjamin.thery@bull.net> Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Reviewed-by: Cong Wang <cwang@twopensource.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: ipmr: fix static mfc/dev leaks on table destruction
When destroying an mrt table the static mfc entries and the static
devices are kept, which leads to devices that can never be destroyed
(because of refcnt taken) and leaked memory, for example:
unreferenced object 0xffff880034c144c0 (size 192):
comm "mfc-broken", pid 4777, jiffies 4320349055 (age 46001.964s)
hex dump (first 32 bytes):
98 53 f0 34 00 88 ff ff 98 53 f0 34 00 88 ff ff .S.4.....S.4....
ef 0a 0a 14 01 02 03 04 00 00 00 00 01 00 00 00 ................
backtrace:
[<ffffffff815c1b9e>] kmemleak_alloc+0x4e/0xb0
[<ffffffff811ea6e0>] kmem_cache_alloc+0x190/0x300
[<ffffffff815931cb>] ip_mroute_setsockopt+0x5cb/0x910
[<ffffffff8153d575>] do_ip_setsockopt.isra.11+0x105/0xff0
[<ffffffff8153e490>] ip_setsockopt+0x30/0xa0
[<ffffffff81564e13>] raw_setsockopt+0x33/0x90
[<ffffffff814d1e14>] sock_common_setsockopt+0x14/0x20
[<ffffffff814d0b51>] SyS_setsockopt+0x71/0xc0
[<ffffffff815cdbf6>] entry_SYSCALL_64_fastpath+0x16/0x7a
[<ffffffffffffffff>] 0xffffffffffffffff
Make sure that everything is cleaned on netns destruction.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Reviewed-by: Cong Wang <cwang@twopensource.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Further investigation showed that this can happen when an *odd* number of
fds are being passed over AF_UNIX sockets.
In these cases CMSG_LEN(i * sizeof(int)) and CMSG_SPACE(i * sizeof(int)),
where i is the number of successfully passed fds, differ by 4 bytes due
to the extra CMSG_ALIGN() padding in CMSG_SPACE() to an 8 byte boundary
on 64 bit. The padding is used to align subsequent cmsg headers in the
control buffer.
When the control buffer passed in from the receiver side *lacks* these 4
bytes (e.g. due to buggy/wrong API usage), then msg->msg_controllen will
overflow in scm_detach_fds():
int cmlen = CMSG_LEN(i * sizeof(int)); <--- cmlen w/o tail-padding
err = put_user(SOL_SOCKET, &cm->cmsg_level);
if (!err)
err = put_user(SCM_RIGHTS, &cm->cmsg_type);
if (!err)
err = put_user(cmlen, &cm->cmsg_len);
if (!err) {
cmlen = CMSG_SPACE(i * sizeof(int)); <--- cmlen w/ 4 byte extra tail-padding
msg->msg_control += cmlen;
msg->msg_controllen -= cmlen; <--- iff no tail-padding space here ...
} ... wrap-around
F.e. it will wrap to a length of 18446744073709551612 bytes in case the
receiver passed in msg->msg_controllen of 20 bytes, and the sender
properly transferred 1 fd to the receiver, so that its CMSG_LEN results
in 20 bytes and CMSG_SPACE in 24 bytes.
In case of MSG_CMSG_COMPAT (scm_detach_fds_compat()), I haven't seen an
issue in my tests as alignment seems always on 4 byte boundary. Same
should be in case of native 32 bit, where we end up with 4 byte boundaries
as well.
In practice, passing msg->msg_controllen of 20 to recvmsg() while receiving
a single fd would mean that on successful return, msg->msg_controllen is
being set by the kernel to 24 bytes instead, thus more than the input
buffer advertised. It could f.e. become an issue if such application later
on zeroes or copies the control buffer based on the returned msg->msg_controllen
elsewhere.
Maximum number of fds we can send is a hard upper limit SCM_MAX_FD (253).
Going over the code, it seems like msg->msg_controllen is not being read
after scm_detach_fds() in scm_recv() anymore by the kernel, good!
Relevant recvmsg() handler are unix_dgram_recvmsg() (unix_seqpacket_recvmsg())
and unix_stream_recvmsg(). Both return back to their recvmsg() caller,
and ___sys_recvmsg() places the updated length, that is, new msg_control -
old msg_control pointer into msg->msg_controllen (hence the 24 bytes seen
in the example).
Long time ago, Wei Yongjun fixed something related in commit 1ac70e7ad24a
("[NET]: Fix function put_cmsg() which may cause usr application memory
overflow").
RFC3542, section 20.2. says:
The fields shown as "XX" are possible padding, between the cmsghdr
structure and the data, and between the data and the next cmsghdr
structure, if required by the implementation. While sending an
application may or may not include padding at the end of last
ancillary data in msg_controllen and implementations must accept both
as valid. On receiving a portable application must provide space for
padding at the end of the last ancillary data as implementations may
copy out the padding at the end of the control message buffer and
include it in the received msg_controllen. When recvmsg() is called
if msg_controllen is too small for all the ancillary data items
including any trailing padding after the last item an implementation
may set MSG_CTRUNC.
Since we didn't place MSG_CTRUNC for already quite a long time, just do
the same as in 1ac70e7ad24a to avoid an overflow.
Btw, even man-page author got this wrong :/ See db939c9b26e9 ("cmsg.3: Fix
error in SCM_RIGHTS code sample"). Some people must have copied this (?),
thus it got triggered in the wild (reported several times during boot by
David and HacKurx).
No Fixes tag this time as pre 2002 (that is, pre history tree).
Reported-by: David Sterba <dave@jikos.cz> Reported-by: HacKurx <hackurx@gmail.com> Cc: PaX Team <pageexec@freemail.hu> Cc: Emese Revfy <re.emese@gmail.com> Cc: Brad Spengler <spender@grsecurity.net> Cc: Wei Yongjun <yongjun_wei@trendmicro.com.cn> Cc: Eric Dumazet <edumazet@google.com> Reviewed-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Jon Paul Maloy [Thu, 19 Nov 2015 19:12:50 +0000 (14:12 -0500)]
tipc: correct settings of broadcast link state
Since commit 5266698661401afc5e ("tipc: let broadcast packet
reception use new link receive function") the broadcast send
link state was meant to always be set to LINK_ESTABLISHED, since
we don't need this link to follow the regular link FSM rules. It
was also the intention that this state anyway shouldn't impact
the run-time working state of the link, since the latter in
reality is controlled by the number of registered peers.
We have now discovered that this assumption is not quite correct.
If the broadcast link is reset because of too many retransmissions,
its state will inadvertently go to LINK_RESETTING, and never go
back to LINK_ESTABLISHED, because the LINK_FAILURE event was not
anticipated. This will work well once, but if it happens a second
time, the reset on a link in LINK_RESETTING has has no effect, and
neither the broadcast link nor the unicast links will go down as
they should.
Furthermore, it is confusing that the management tool shows that
this link is in UP state when that obviously isn't the case.
We now ensure that this state strictly follows the true working
state of the link. The state is set to LINK_ESTABLISHED when
the number of peers is non-zero, and to LINK_RESET otherwise.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Måns Rullgård [Thu, 19 Nov 2015 13:02:59 +0000 (13:02 +0000)]
net: ethernet: add driver for Aurora VLSI NB8800 Ethernet controller
This adds a driver for the Aurora VLSI NB8800 Ethernet controller.
It is an almost complete rewrite of a driver originally found in
a Sigma Designs 2.6.22 tree.
Signed-off-by: Mans Rullgard <mans@mansr.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This is the last remaining warning for arm64, and I'd like to get rid of
it. We don't really know the cache line size, architecturally it would
be at least 16 bytes, but all implementations I found have 64 or 128
bytes. Configuring tulip for 32-byte lines as we do on ARM32 seems to
be the safe but slow default, and nobody who cares about performance these
days would use a tulip chip anyway, so we can just use that.
To save the next person the job of trying to find out what this is for
and picking a default for their architecture just to kill off the warning,
I'm now removing the preprocessor #warning and turning it into a pr_warn
or dev_warn that prints the equivalent information when the driver gets
loaded.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Grant Grundler <grundler@parisc-linux.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz [Thu, 19 Nov 2015 09:56:51 +0000 (11:56 +0200)]
bnx2x: Fix vxlan removal
Commmit ac7eccd4d48fc "bnx2x: track vxlan port count" contains a bug -
Instead of achieving the required goal, vxlan configuration would not
be removed since we're decrementing the port instead of the counter.
CC: Jiri Benc <jbenc@redhat.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 19 Nov 2015 05:03:33 +0000 (21:03 -0800)]
tcp: fix potential huge kmalloc() calls in TCP_REPAIR
tcp_send_rcvq() is used for re-injecting data into tcp receive queue.
Problems :
- No check against size is performed, allowed user to fool kernel in
attempting very large memory allocations, eventually triggering
OOM when memory is fragmented.
- In case of fault during the copy we do not return correct errno.
Lets use alloc_skb_with_frags() to cook optimal skbs.
Fixes: 292e8d8c8538 ("tcp: Move rcvq sending to tcp_input.c") Fixes: c0e88ff0f256 ("tcp: Repair socket queues") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Pavel Emelyanov <xemul@parallels.com> Acked-by: Pavel Emelyanov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yuchung Cheng [Thu, 19 Nov 2015 02:17:31 +0000 (18:17 -0800)]
tcp: fix Fast Open snmp over-counting bug
Fix incrementing TCPFastOpenActiveFailed snmp stats multiple times
when the handshake experiences multiple SYN timeouts.
Signed-off-by: Yuchung Cheng <ycheng@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yuchung Cheng [Thu, 19 Nov 2015 02:17:30 +0000 (18:17 -0800)]
tcp: disable Fast Open on timeouts after handshake
Some middle-boxes black-hole the data after the Fast Open handshake
(https://www.ietf.org/proceedings/94/slides/slides-94-tcpm-13.pdf).
The exact reason is unknown. The work-around is to disable Fast Open
temporarily after multiple recurring timeouts with few or no data
delivered in the established state.
Signed-off-by: Yuchung Cheng <ycheng@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Christoph Paasch <cpaasch@apple.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Lindgren [Thu, 19 Nov 2015 01:27:25 +0000 (17:27 -0800)]
net: cpsw: Fix ethernet regression for dm814x
Commit b6745f6e4e63 ("drivers: net: cpsw: davinci_emac: move reading mac
id to common file") started using of_machine_is_compatible for detecting
type but missed at dm8148 causing Ethernet to stop working.
Let's fix the issue by adding handling for dm814x.
Cc: Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Acked-by: Mugunthnan V N <mugunthanvnm@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 18 Nov 2015 20:40:13 +0000 (12:40 -0800)]
tcp: md5: fix lockdep annotation
When a passive TCP is created, we eventually call tcp_md5_do_add()
with sk pointing to the child. It is not owner by the user yet (we
will add this socket into listener accept queue a bit later anyway)
But we do own the spinlock, so amend the lockdep annotation to avoid
following splat :
Fixes: a8afca0329988 ("tcp: md5: protects md5sig_info with RCU") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bjørn Mork [Wed, 18 Nov 2015 20:13:07 +0000 (21:13 +0100)]
net: qmi_wwan: add XS Stick W100-2 from 4G Systems
Thomas reports
"
4gsystems sells two total different LTE-surfsticks under the same name.
..
The newer version of XS Stick W100 is from "omega"
..
Under windows the driver switches to the same ID, and uses MI03\6 for
network and MI01\6 for modem.
..
echo "1c9e 9b01" > /sys/bus/usb/drivers/qmi_wwan/new_id
echo "1c9e 9b01" > /sys/bus/usb-serial/drivers/option1/new_id
Sergei Shtylyov [Wed, 18 Nov 2015 22:39:51 +0000 (01:39 +0300)]
ravb: fix WARNING in __free_irq()
When the R8A7795 support was added to the driver, little attention was paid
to the ravb_open() error path: free_irq() for the EMAC interrupt was called
uncoditionally, unlike request_irq(), and in a wrong order as well...
As a result, on the R-Car gen2 SoCs I started getting the following in case
of a device opening error:
Fix up the free_irq() call order and add a new label on the error path.
Fixes: 22d4df8ff3a3 ("ravb: Add support for r8a7795 SoC") Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Acked-by: Simon Horman <horms+renesas@verge.net.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Aya Mahfouz [Wed, 18 Nov 2015 06:36:44 +0000 (08:36 +0200)]
net: dns_resolver: convert time_t to time64_t
Changes the definition of the pointer _expiry from time_t to
time64_t. This is to handle the Y2038 problem where time_t
will overflow in the year 2038. The change is safe because
the kernel subsystems that call dns_query pass NULL.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Aya Mahfouz <mahfouz.saif.elyazal@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Wed, 18 Nov 2015 15:40:19 +0000 (16:40 +0100)]
net/ip6_tunnel: fix dst leak
the commit cdf3464e6c6b ("ipv6: Fix dst_entry refcnt bugs in ip6_tunnel")
introduced percpu storage for ip6_tunnel dst cache, but while clearing
such cache it used raw_cpu_ptr to walk the per cpu entries, so cached
dst on non current cpu are not actually reset.
This patch replaces raw_cpu_ptr with per_cpu_ptr, properly cleaning
such storage.
Fixes: cdf3464e6c6b ("ipv6: Fix dst_entry refcnt bugs in ip6_tunnel") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Acked-by: Martin KaFai Lau <kafai@fb.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Pope [Wed, 18 Nov 2015 01:21:07 +0000 (18:21 -0700)]
ethernet/atheros/alx: add Killer E2400 device ID
This patch adds the PCI device ID (0xe0a1) and alx_pci_tbl entry for the
Killer E2400 Ethernet controller, modeled after the Killer E2200
controller support (0xe091) already present in the alx driver.
This patch was originally authored by Ben Pope, but it got held up by
issues in the commit message, so I'm resubmitting it on his behalf.
I've extensively used a kernel with this patch on a System76 serw9
laptop and am quite confident it works well (at least on the hardware I
have available for testing).
Note that as a favor to System76, Ubuntu has been carrying this as a
sauce patch in their 4.2 based Wily kernel, which presumably has given
it real-world testing on other E2400 equipped hardware (I don't know of
any Ubuntu kernel bugs filed about it):
Signed-off-by: Jason Gerard DeRose <jason@system76.com> Signed-off-by: Ben Pope <benpope81@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Wed, 18 Nov 2015 16:59:29 +0000 (08:59 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Martin Schwidefsky:
"Assorted bug fixes, the mlock2 system call gets added, and one
improvement. The boot from dasd devices is now possible from a wider
range of devices"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390: remove SALIPL loader
s390: wire up mlock2 system call
s390: remove g5 elf platform support
s390: avoid cache aliasing under z/VM and KVM
s390/sclp: _sclp_wait_int(): retain full PSW mask
s390/zcrypt: Fix initialisation when zcrypt is built-in
s390/zcrypt: Fix kernel crash on systems without AP bus support
s390: add support for ipl devices in subchannel sets > 0
s390/ipl: fix out of bounds access in scpdata_write
s390/pci_dma: improve debugging of errors during dma map
s390/pci_dma: handle dma table failures
s390/pci_dma: unify label of invalid translation table entries
s390/syscalls: remove system call number calculation
s390/cio: simplify css_generate_pgid
s390/diag: add a s390 prefix to the diagnose trace point
s390/head: fix error message on unsupported hardware
Linus Torvalds [Wed, 18 Nov 2015 16:43:29 +0000 (08:43 -0800)]
Merge tag 'hwmon-for-linus-v4.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
"Fix build issues in scpi and ina2xx drivers, update scpi driver to
support recent firmware, and fix an uninitialized variable warning in
applesmc driver"
1) Fix list tests in netfilter ingress support, from Florian Westphal.
2) Fix reversal of input and output interfaces in ingress hook
invocation, from Pablo Neira Ayuso.
3) We have a use after free in r8169, caught by Dave Jones, fixed by
Francois Romieu.
4) Splice use-after-free fix in AF_UNIX frmo Hannes Frederic Sowa.
5) Three ipv6 route handling bug fixes from Martin KaFai Lau:
a) Don't create clone routes not managed by the fib6 tree
b) Don't forget to check expiration of DST_NOCACHE routes.
c) Handle rt->dst.from == NULL properly.
6) Several AF_PACKET fixes wrt transport header setting and SKB
protocol setting, from Daniel Borkmann.
7) Fix thunder driver crash on shutdown, from Pavel Fedin.
8) Several Mellanox driver fixes (max MTU calculations, use of correct
DMA unmap in TX path, etc.) from Saeed Mahameed, Tariq Toukan, Doron
Tsur, Achiad Shochat, Eran Ben Elisha, and Noa Osherovich.
9) Several mv88e6060 DSA driver fixes (wrong bit definitions for
certain registers, etc.) from Neil Armstrong.
10) Make sure to disable preemption while updating per-cpu stats of ip
tunnels, from Jason A. Donenfeld.
11) Various ARM64 bpf JIT fixes, from Yang Shi.
12) Flush icache properly in ARM JITs, from Daniel Borkmann.
13) Fix masking of RX and TX interrupts in ravb driver, from Masaru
Nagai.
14) Fix netdev feature propagation for devices not implementing
->ndo_set_features(). From Nikolay Aleksandrov.
15) Big endian fix in vmxnet3 driver, from Shrikrishna Khare.
16) RAW socket code increments incorrect SNMP counters, fix from Ben
Cartwright-Cox.
17) IPv6 multicast SNMP counters are bumped twice, fix from Neil Horman.
18) Fix handling of VLAN headers on stacked devices when REORDER is
disabled. From Vlad Yasevich.
19) Fix SKB leaks and use-after-free in ipvlan and macvlan drivers, from
Sabrina Dubroca.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (83 commits)
MAINTAINERS: Update Mellanox's Eth NIC driver entries
net/core: revert "net: fix __netdev_update_features return.." and add comment
af_unix: take receive queue lock while appending new skb
rtnetlink: fix frame size warning in rtnl_fill_ifinfo
net: use skb_clone to avoid alloc_pages failure.
packet: Use PAGE_ALIGNED macro
packet: Don't check frames_per_block against negative values
net: phy: Use interrupts when available in NOLINK state
phy: marvell: Add support for 88E1540 PHY
arm64: bpf: make BPF prologue and epilogue align with ARM64 AAPCS
macvlan: fix leak in macvlan_handle_frame
ipvlan: fix use after free of skb
ipvlan: fix leak in ipvlan_rcv_frame
vlan: Do not put vlan headers back on bridge and macvlan ports
vlan: Fix untag operations of stacked vlans with REORDER_HEADER off
via-velocity: unconditionally drop frames with bad l2 length
ipg: Remove ipg driver
dl2k: Add support for IP1000A-based cards
snmp: Remove duplicate OUTMCAST stat increment
net: thunder: Check for driver data in nicvf_remove()
...
net/core: revert "net: fix __netdev_update_features return.." and add comment
This reverts commit 00ee59271777 ("net: fix __netdev_update_features return
on ndo_set_features failure")
and adds a comment explaining why it's okay to return a value other than
0 upon error. Some drivers might actually change flags and return an
error so it's better to fire a spurious notification rather than miss
these.
CC: Michał Mirosław <mirq-linux@rere.qmqm.pl> Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
af_unix: take receive queue lock while appending new skb
While possibly in future we don't necessarily need to use
sk_buff_head.lock this is a rather larger change, as it affects the
af_unix fd garbage collector, diag and socket cleanups. This is too much
for a stable patch.
For the time being grab sk_buff_head.lock without disabling bh and irqs,
so don't use locked skb_queue_tail.
Fixes: 869e7c62486e ("net: af_unix: implement stream sendpage support") Cc: Eric Dumazet <edumazet@google.com> Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Reported-by: Eric Dumazet <edumazet@google.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
rtnetlink: fix frame size warning in rtnl_fill_ifinfo
Fix the following warning:
CC net/core/rtnetlink.o
net/core/rtnetlink.c: In function ‘rtnl_fill_ifinfo’:
net/core/rtnetlink.c:1308:1: warning: the frame size of 2864 bytes is larger than 2048 bytes [-Wframe-larger-than=]
}
^
by splitting up the huge rtnl_fill_ifinfo into some smaller ones, so we
don't have the huge frame allocations at the same time.
Cc: Eric Dumazet <edumazet@google.com> Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Martin Zhang [Tue, 17 Nov 2015 12:49:30 +0000 (20:49 +0800)]
net: use skb_clone to avoid alloc_pages failure.
1. new skb only need dst and ip address(v4 or v6).
2. skb_copy may need high order pages, which is very rare on long running server.
Signed-off-by: Junwei Zhang <linggao.zjw@alibaba-inc.com> Signed-off-by: Martin Zhang <martinbj2008@gmail.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Mon, 16 Nov 2015 22:36:46 +0000 (23:36 +0100)]
net: phy: Use interrupts when available in NOLINK state
The NOLINK state will poll the phy once a second to see if the link
has come up. If the phy has an interrupt line, this polling can be
skipped, since the phy should interrupt when the link returns.
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
The 88E1540 can be found embedded in the Marvell 88E6352 switch. It
is compatible with the 88E1510, so add support for it, using the 88E1510 specific functions.
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Yang Shi [Mon, 16 Nov 2015 22:35:35 +0000 (14:35 -0800)]
arm64: bpf: make BPF prologue and epilogue align with ARM64 AAPCS
Save and restore FP/LR in BPF prog prologue and epilogue, save SP to FP
in prologue in order to get the correct stack backtrace.
However, ARM64 JIT used FP (x29) as eBPF fp register, FP is subjected to
change during function call so it may cause the BPF prog stack base address
change too.
Use x25 to replace FP as BPF stack base register (fp). Since x25 is callee
saved register, so it will keep intact during function call.
It is initialized in BPF prog prologue when BPF prog is started to run
everytime. Save and restore x25/x26 in BPF prologue and epilogue to keep
them intact for the outside of BPF. Actually, x26 is unnecessary, but SP
requires 16 bytes alignment.
CC: Zi Shen Lim <zlim.lnx@gmail.com> CC: Xi Wang <xi.wang@gmail.com> Signed-off-by: Yang Shi <yang.shi@linaro.org> Acked-by: Zi Shen Lim <zlim.lnx@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sabrina Dubroca [Mon, 16 Nov 2015 21:54:20 +0000 (22:54 +0100)]
macvlan: fix leak in macvlan_handle_frame
Reset pskb in macvlan_handle_frame in case skb_share_check returned a
clone.
Fixes: 8a4eb5734e8d ("net: introduce rx_handler results and logic around that") Signed-off-by: Sabrina Dubroca <sd@queasysnail.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Sabrina Dubroca [Mon, 16 Nov 2015 21:44:53 +0000 (22:44 +0100)]
ipvlan: fix use after free of skb
ipvlan_handle_frame is a rx_handler, and when it returns a value other
than RX_HANDLER_CONSUMED (here, NET_RX_DROP aka RX_HANDLER_ANOTHER),
__netif_receive_skb_core expects that the skb still exists and will
process it further, but we just freed it.
Fixes: 2ad7bf363841 ("ipvlan: Initial check-in of the IPVLAN driver.") Signed-off-by: Sabrina Dubroca <sd@queasysnail.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Sabrina Dubroca [Mon, 16 Nov 2015 21:34:26 +0000 (22:34 +0100)]
ipvlan: fix leak in ipvlan_rcv_frame
Pass a **skb to ipvlan_rcv_frame so that if skb_share_check returns a
new skb, we actually use it during further processing.
It's safe to ignore the new skb in the ipvlan_xmit_* functions, because
they call ipvlan_rcv_frame with local == true, so that dev_forward_skb
is called and always takes ownership of the skb.
Fixes: 2ad7bf363841 ("ipvlan: Initial check-in of the IPVLAN driver.") Signed-off-by: Sabrina Dubroca <sd@queasysnail.net> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 17 Nov 2015 19:38:36 +0000 (14:38 -0500)]
Merge branch 'vlan-reorder'
Vladislav Yasevich says:
====================
Fix issues with vlans without REORDER_HEADER
A while ago Phil Sutter brought up an issue with vlans without
REORDER_HEADER and bridges. The problem was that if a vlan
without REORDER_HEADER was a port in the bridge, the bridge ended
up forwarding corrupted packets that still contained the vlan header.
The same issue exists for bridge mode macvlan/macvtap devices.
An additional issue with vlans without REORDER_HEADER is that stacking
them also doesn't work. The reason here is that skb_reorder_vlan_header()
function assumes that it on ETH_HLEN bytes deep into the packet. That
is not the case, when you a vlan without REORRDER_HEADER flag set.
This series attempts to correct these 2 issues.
1) To solve the stacked vlans problem, the patch simply use
skb->mac_len as an offset to start copying mac addresses that
is part of header reordering.
2) To fix the issue with bridge/macvlan/macvtap, the second patch
simply doesn't write the vlan header back to the packet if the
vlan device is either a bridge or a macvlan port. This ends up
being the simplest and least performance intrussive solution.
I've considered extending patch 2 to all stacked devices (essentially
checked for the presense of rx_handler), but that feels like a broader
restriction and _may_ break existing uses.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Vlad Yasevich [Mon, 16 Nov 2015 20:43:45 +0000 (15:43 -0500)]
vlan: Do not put vlan headers back on bridge and macvlan ports
When a vlan is configured with REORDER_HEADER set to 0, the vlan
header is put back into the packet and makes it appear that
the vlan header is still there even after it's been processed.
This posses a problem for bridge and macvlan ports. The packets
passed to those device may be forwarded and at the time of the
forward, vlan headers end up being unexpectedly present.
With the patch, we make sure that we do not put the vlan header
back (when REORDER_HEADER is 0) if a bridge or macvlan has
been configured on top of the vlan device.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vlad Yasevich [Mon, 16 Nov 2015 20:43:44 +0000 (15:43 -0500)]
vlan: Fix untag operations of stacked vlans with REORDER_HEADER off
When we have multiple stacked vlan devices all of which have
turned off REORDER_HEADER flag, the untag operation does not
locate the ethernet addresses correctly for nested vlans.
The reason is that in case of REORDER_HEADER flag being off,
the outer vlan headers are put back and the mac_len is adjusted
to account for the presense of the header. Then, the subsequent
untag operation, for the next level vlan, always use VLAN_ETH_HLEN
to locate the begining of the ethernet header and that ends up
being a multiple of 4 bytes short of the actuall beginning
of the mac header (the multiple depending on the how many vlan
encapsulations ethere are).
As a reslult, if there are multiple levles of vlan devices
with REODER_HEADER being off, the recevied packets end up
being dropped.
To solve this, we use skb->mac_len as the offset. The value
is always set on receive path and starts out as a ETH_HLEN.
The value is also updated when the vlan header manupations occur
so we know it will be correct.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Timo Teräs [Mon, 16 Nov 2015 12:36:32 +0000 (14:36 +0200)]
via-velocity: unconditionally drop frames with bad l2 length
By default the driver allowed incorrect frames to be received. What is
worse the code does not handle very short frames correctly. The FCS
length is unconditionally subtracted, and the underflow can cause
skb_put to be called with large number after implicit cast to unsigned.
And indeed, an skb_over_panic() was observed with via-velocity.
This removes the module parameter as it does not work in it's
current state, and should be implemented via NETIF_F_RXALL if needed.
Suggested-by: Francois Romieu <romieu@fr.zoreil.com> Signed-off-by: Timo Teräs <timo.teras@iki.fi> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Tue, 17 Nov 2015 18:11:08 +0000 (10:11 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs fixes from Al Viro:
"A fs-cache regression fix, and adding a warning about obnoxiou^W
moderation of list given in MAINTAINERS"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
MAINTAINERS: linux-cachefs@redhat.com is moderated for non-subscribers
FS-Cache: Add missing initialization of ret in cachefiles_write_page()
Larry Finger [Tue, 10 Nov 2015 16:46:11 +0000 (10:46 -0600)]
rtlwifi: rtl8821ae: Fix lockups on boot
In commit 54328e64047a5 ("rtlwifi: rtl8821ae: Fix system lockups on boot"),
an attempt was made to fix a regression introduced in commit 1277fa2ab2f9
("rtlwifi: Remove the clear interrupt routine from all drivers").
Unfortunately, there were logic errors in that patch that prevented
affected boxes from booting even after that patch was applied.
The actual cause of the original problem is unknown as none of the
developers have systems that are affected.
Fixes: 54328e64047a ("rtlwifi: rtl8821ae: Fix system lockups on boot") Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Stable <stable@vger.kernel.org> [V4.1+] Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
projects / linux-beck.git / log