Ben Hutchings [Sat, 13 Dec 2008 05:42:42 +0000 (21:42 -0800)]
sfc: Don't count RX checksum errors during loopback self-test
The loopback self-test checks that IP packets with incorrect checksums
are not altered when sent on a queue with checksum generation off.
These should not contribute to RX error statistics.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Neil Turton [Sat, 13 Dec 2008 05:41:06 +0000 (21:41 -0800)]
sfc: Add option to use a separate channel for TX completions
In a bidirectional forwarding test, we find that the best performance
is achieved by sending the TX completion interrupts from one NIC to a
CPU which shares an L2 cache with RX completion interrupts from the
other NIC. To facilitate this, add an option (through a module
parameter) to create separate channels for RX and TX completion with
separate IRQs when MSI-X is available.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Sat, 13 Dec 2008 05:34:25 +0000 (21:34 -0800)]
sfc: Work around unreliable strap pins
The SFC4000 has strap pins indicating the presence of SPI flash and/or
EEPROM. These pins are also used for GPIO, and in some cases they may
be read wrongly at reset. However, on production boards it must boot
from one or the other device, so we can assume the boot device is
present and read the board config from there.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Sat, 13 Dec 2008 05:33:50 +0000 (21:33 -0800)]
sfc: Clean up waits for flash/EEPROM operations
Make falcon_spi_wait() ignore the write timer - it is only relevant to
write commands, it only works for the device that contains VPD, and it
might not be initialised properly at all.
Rename falcon_spi_fast_wait() to falcon_spi_wait_write(), reflecting
its use, and make it wait up to 10 ms (not 1 ms) since buffered writes
to EEPROM may take this long to complete.
Make both wait functions sleep instead of busy-waiting.
Replace wait for command completion at top of falcon_spi_cmd() with a
single poll; no command should be running when the function starts.
Correct some comments.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Hannes Eder [Sat, 13 Dec 2008 05:18:32 +0000 (21:18 -0800)]
mISDN: comment out unused symbols
Fix this sparse warnings:
drivers/isdn/hardware/mISDN/hfcmulti.c:794: warning: 'vpm_check' defined but not used
drivers/isdn/mISDN/dsp_cmx.c:1546: warning: 'dsp_start_jiffies' defined but not used
Signed-off-by: Hannes Eder <hannes@hanneseder.net> Acked-by: Karsten Keil <kkeil@suse.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Hannes Eder [Sat, 13 Dec 2008 05:16:06 +0000 (21:16 -0800)]
mISDN: un-export symbol 'plx_lock'
'plx_lock' is only used within hfcmulti.c.
Fix this warning:
drivers/isdn/hardware/mISDN/hfcmulti.c:176:1: warning: symbol 'plx_lock' shadows an earlier one
drivers/isdn/hardware/mISDN/hfcmulti.c:175:19: originally declared here
Signed-off-by: Hannes Eder <hannes@hanneseder.net> Acked-by: Karsten Keil <kkeil@suse.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Hannes Eder [Sat, 13 Dec 2008 05:15:17 +0000 (21:15 -0800)]
mISDN: make global symbols static or include header files
The warnings fixed by including an header file for the appropriate
prototype are marked with "*", for all others the corresonponding
symbol has been made static. This patch fixes all such issues in
mISDN.
Fix this sparse warnings:
drivers/isdn/hardware/mISDN/hfcmulti.c:174:5: warning: symbol 'plxsd_master' was not declared. Should it be static?
drivers/isdn/hardware/mISDN/hfcmulti.c:426:1: warning: symbol 'write_fifo_regio' was not declared. Should it be static?
drivers/isdn/hardware/mISDN/hfcmulti.c:447:1: warning: symbol 'write_fifo_pcimem' was not declared. Should it be static?
drivers/isdn/hardware/mISDN/hfcmulti.c:469:1: warning: symbol 'read_fifo_regio' was not declared. Should it be static?
drivers/isdn/hardware/mISDN/hfcmulti.c:491:1: warning: symbol 'read_fifo_pcimem' was not declared. Should it be static?
drivers/isdn/hardware/mISDN/hfcmulti.c:710:1: warning: symbol 'vpm_init' was not declared. Should it be static?
drivers/isdn/hardware/mISDN/hfcmulti.c:793:1: warning: symbol 'vpm_check' was not declared. Should it be static?
drivers/isdn/hardware/mISDN/hfcmulti.c:816:1: warning: symbol 'vpm_echocan_on' was not declared. Should it be static?
drivers/isdn/hardware/mISDN/hfcmulti.c:848:1: warning: symbol 'vpm_echocan_off' was not declared. Should it be static?
* drivers/isdn/mISDN/l1oip_codec.c:224:1: warning: symbol 'l1oip_law_to_4bit' was not declared. Should it be static?
* drivers/isdn/mISDN/l1oip_codec.c:261:1: warning: symbol 'l1oip_4bit_to_law' was not declared. Should it be static?
* drivers/isdn/mISDN/l1oip_codec.c:281:1: warning: symbol 'l1oip_alaw_to_ulaw' was not declared. Should it be static?
* drivers/isdn/mISDN/l1oip_codec.c:294:1: warning: symbol 'l1oip_ulaw_to_alaw' was not declared. Should it be static?
* drivers/isdn/mISDN/l1oip_codec.c:311:1: warning: symbol 'l1oip_4bit_free' was not declared. Should it be static?
* drivers/isdn/mISDN/l1oip_codec.c:322:1: warning: symbol 'l1oip_4bit_alloc' was not declared. Should it be static?
drivers/isdn/mISDN/core.c:29:1: warning: symbol 'device_lock' was not declared. Should it be static?
drivers/isdn/mISDN/core.c:34:1: warning: symbol 'bp_lock' was not declared. Should it be static?
drivers/isdn/mISDN/core.c:196:1: warning: symbol 'mISDNInit' was not declared. Should it be static?
drivers/isdn/mISDN/core.c:227:6: warning: symbol 'mISDN_cleanup' was not declared. Should it be static?
drivers/isdn/mISDN/stack.c:40:1: warning: symbol 'mISDN_queue_message' was not declared. Should it be static?
* drivers/isdn/mISDN/layer1.c:388:1: warning: symbol 'l1_init' was not declared. Should it be static?
* drivers/isdn/mISDN/layer1.c:400:1: warning: symbol 'l1_cleanup' was not declared. Should it be static?
drivers/isdn/mISDN/layer2.c:469:1: warning: symbol 'iframe_error' was not declared. Should it be static?
drivers/isdn/mISDN/layer2.c:487:1: warning: symbol 'super_error' was not declared. Should it be static?
drivers/isdn/mISDN/layer2.c:496:1: warning: symbol 'unnum_error' was not declared. Should it be static?
drivers/isdn/mISDN/layer2.c:509:1: warning: symbol 'UI_error' was not declared. Should it be static?
drivers/isdn/mISDN/layer2.c:522:1: warning: symbol 'FRMR_error' was not declared. Should it be static?
drivers/isdn/mISDN/layer2.c:1069:1: warning: symbol 'enquiry_cr' was not declared. Should it be static?
* drivers/isdn/mISDN/layer2.c:2196:1: warning: symbol 'Isdnl2_Init' was not declared. Should it be static?
* drivers/isdn/mISDN/layer2.c:2210:1: warning: symbol 'Isdnl2_cleanup' was not declared. Should it be static?
drivers/isdn/mISDN/tei.c:397:1: warning: symbol 'random_ri' was not declared. Should it be static?
* drivers/isdn/mISDN/timerdev.c:277:1: warning: symbol 'mISDN_inittimer' was not declared. Should it be static?
* drivers/isdn/mISDN/timerdev.c:288:6: warning: symbol 'mISDN_timer_cleanup' was not declared. Should it be static?
drivers/isdn/mISDN/dsp_core.c:164:12: warning: symbol 'mISDN_dsp_revision' was not declared. Should it be static?
drivers/isdn/mISDN/dsp_cmx.c:1543:5: warning: symbol 'samplecount' was not declared. Should it be static?
drivers/isdn/mISDN/dsp_cmx.c:1546:5: warning: symbol 'dsp_start_jiffies' was not declared. Should it be static?
drivers/isdn/mISDN/dsp_cmx.c:1547:16: warning: symbol 'dsp_start_tv' was not declared. Should it be static?
drivers/isdn/mISDN/dsp_tones.c:239:3: warning: symbol 'pattern' was not declared. Should it be static?
drivers/isdn/mISDN/dsp_audio.c:33:4: warning: symbol 'dsp_audio_ulaw_to_alaw' was not declared. Should it be static?
Signed-off-by: Hannes Eder <hannes@hanneseder.net> Acked-by: Karsten Keil <kkeil@suse.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Hannes Eder [Sat, 13 Dec 2008 05:13:45 +0000 (21:13 -0800)]
mISDN: consistently define 'debug' as '*u_int'
Impact: change data type for variable 'debug' from *int to *u_int,
same for the argument type of mISDN_inittimer
In "core.h" mISDN_inittimer is declared with the argument type "*u_int", make
the definition in "timerdev.c" match this.
This fixes also this warnings:
drivers/isdn/mISDN/layer1.c:391:8: warning: incorrect type in assignment (different signedness)
drivers/isdn/mISDN/layer1.c:391:8: expected int *static [toplevel] debug
drivers/isdn/mISDN/layer1.c:391:8: got unsigned int [usertype] *deb
drivers/isdn/mISDN/layer2.c:2200:8: warning: incorrect type in assignment (different signedness)
drivers/isdn/mISDN/layer2.c:2200:8: expected int *static [toplevel] debug
drivers/isdn/mISDN/layer2.c:2200:8: got unsigned int [usertype] *deb
drivers/isdn/mISDN/socket.c:769:8: warning: incorrect type in assignment (different signedness)
drivers/isdn/mISDN/socket.c:769:8: expected int *static [toplevel] debug
drivers/isdn/mISDN/socket.c:769:8: got unsigned int [usertype] *deb
Signed-off-by: Hannes Eder <hannes@hanneseder.net> Acked-by: Karsten Keil <kkeil@suse.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Hannes Eder [Sat, 13 Dec 2008 05:11:28 +0000 (21:11 -0800)]
mISDN: use NULL pointer instead of plain integer
Fix more than 100 (all remaining in mISDN) sparse warnings:
drivers/isdn/hardware/mISDN/hfcmulti.c:***:**: warning: Using plain integer as NULL pointer
drivers/isdn/mISDN/dsp_tones.c:***:**: warning: Using plain integer as NULL pointer
drivers/isdn/mISDN/dsp_pipeline.c:***:**: warning: Using plain integer as NULL pointer
Signed-off-by: Hannes Eder <hannes@hanneseder.net> Acked-by: Karsten Keil <kkeil@suse.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Implements the KS8695 ethernet device (ks8695net).
This driver is only of use on the KS8695 which is an ARM9 based SoC. The
documentation on this SoC is sparse and poor, with barely a register
description and a rough outline of how the ethernet works, this driver was
therefore written with strong reference to the Micrel supplied Linux 2.6.9
port, and to Andrew Victor's ks8695eth driver.
Signed-off-by: Daniel Silverstone <dsilvers@simtec.co.uk> Signed-off-by: Vincent Sanders <vince@simtec.co.uk> Acked-by: Ben Dooks <ben@simtec.co.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Atsushi Nemoto [Fri, 12 Dec 2008 04:58:04 +0000 (20:58 -0800)]
tc35815: Enable StripCRC feature
The chip can strip CRC automatically on receiving. Enable it.
Also fix potential RX_BUF_SIZE calculation bug which was obscured by
alignment. And use proper symbols (NET_IP_ALIGN, ETH_FCS_LEN, etc.)
instead of magic numbers.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp> Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher [Fri, 12 Dec 2008 04:34:19 +0000 (20:34 -0800)]
igb: fixup AER with proper error handling
Based on Peter Waskiewicz patch for ixgbe. Add error handling based on
Hemminger's recommendation.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Leblond [Thu, 11 Dec 2008 01:24:33 +0000 (17:24 -0800)]
netfilter: xt_NFLOG is dependant of nfnetlink_log
The patch "don't call nf_log_packet in NFLOG module" make xt_NFLOG
dependant of nfnetlink_log. This patch forces the dependencies to fix
compilation in case only xt_NFLOG compilation was asked and modifies the
help message accordingly to the change.
Signed-off-by: Eric Leblond <eric@inl.fr> Signed-off-by: David S. Miller <davem@davemloft.net>
Benjamin Thery [Thu, 11 Dec 2008 00:30:15 +0000 (16:30 -0800)]
netns: ip6mr: enable namespace support in ipv6 multicast forwarding code
This last patch makes the appropriate changes to use and propagate the
network namespace where needed in IPv6 multicast forwarding code.
This consists mainly in replacing all the remaining init_net occurences
with current netns pointer retrieved from sockets, net devices or
mfc6_caches depending on the routines' contexts.
Some routines receive a new 'struct net' parameter to propagate the current
netns:
* ip6mr_get_route
* ip6mr_cache_report
* ip6mr_cache_find
* ip6mr_cache_unresolved
* mif6_add/mif6_delete
* ip6mr_mfc_add/ip6mr_mfc_delete
* ip6mr_reg_vif
All the IPv6 multicast forwarding variables moved to struct netns_ipv6 by
the previous patches are now referenced in the correct namespace.
Changelog:
==========
* Take into account the net associated to mfc6_cache when matching entries in
mfc_unres_queue list.
* Call mroute_clean_tables() in ip6mr_net_exit() to free memory allocated
per-namespace.
* Call dev_net_set() in ip6mr_reg_vif() to initialize dev->nd_net
correctly.
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Preliminary work to make IPv6 multicast forwarding netns-aware.
Declare variable cache_resolve_queue_len per-namespace: moves it into
struct netns_ipv6.
This variable counts the number of unresolved cache entries queued in the
list mfc_unres_queue. This list is kept global to all netns as the number
of entries per namespace is limited to 10 (hardcoded in routine
ip6mr_cache_unresolved).
Entries belonging to different namespaces in mfc_unres_queue will be
identified by matching the mfc_net member introduced previously in
struct mfc6_cache.
Keeping this list global to all netns, also allows us to keep a single
timer (ipmr_expire_timer) to handle their expiration.
In some places cache_resolve_queue_len value was tested for arming
or deleting the timer. These tests were equivalent to testing
mfc_unres_queue value instead and are replaced in this patch.
At the moment, cache_resolve_queue_len is only referenced in init_net.
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the driver to select 16-bit or 32-bit bus access at runtime,
at a small performance cost.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com> Acked-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements the PCIe Advanced Error Reporting callbacks in
ixgbe. The 82598 hardware supports AER, so we enable it.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Wed, 10 Dec 2008 09:09:53 +0000 (01:09 -0800)]
igb: Correctly determine pci-e function number in virtual environment
When running in a virtual environment the ports of an 82575/6 can appear to
be single function devices which is not correct. To resolve this we rely
on the function number stored in the status register.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Wed, 10 Dec 2008 09:08:59 +0000 (01:08 -0800)]
igb: update handling of RCTL for smaller buffer sizes
As we begin to move into virtualization the use of a global value for
buffer sizes becomes undesirable. This change makes it so only 256 and 512
byte buffers require use of the RCTL register.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
bonding: make tbl argument to bond_parse_parm() const
bond_parse_parm() parses a parameter table for a particular value and
is therefore not modifying the table at all. Therefore make the 2nd
argument const, thus allowing to make the tables const later.
Signed-off-by: Holger Eitzenberger <holger@eitzenberger.org> Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/bonding/bond_ipv6.c: In function 'bond_na_send':
drivers/net/bonding/bond_ipv6.c:75: error: 'slave' undeclared (first use in this function)
drivers/net/bonding/bond_ipv6.c:75: error: (Each undeclared identifier is reported only once
drivers/net/bonding/bond_ipv6.c:75: error: for each function it appears in.)
This patch fixes that.
Signed-off-by: Holger Eitzenberger <holger@eitzenberger.org> Signed-off-by: David S. Miller <davem@davemloft.net>
htb_id_find_next_upper() is usually called to find a class with next
id after some previously removed class, so let's move a check for
equality to the end: it's the least likely here.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Gerrit Renker [Mon, 8 Dec 2008 09:19:06 +0000 (01:19 -0800)]
dccp ccid-2: Phase out the use of boolean Ack Vector sysctl
This removes the use of the sysctl and the minisock variable for the Send Ack
Vector feature, as it now is handled fully dynamically via feature negotiation
(i.e. when CCID-2 is enabled, Ack Vectors are automatically enabled as per
RFC 4341, 4.).
Using a sysctl in parallel to this implementation would open the door to
crashes, since much of the code relies on tests of the boolean minisock /
sysctl variable. Thus, this patch replaces all tests of type
if (dccp_msk(sk)->dccpms_send_ack_vector)
/* ... */
with
if (dp->dccps_hc_rx_ackvec != NULL)
/* ... */
The dccps_hc_rx_ackvec is allocated by the dccp_hdlr_ackvec() when feature
negotiation concluded that Ack Vectors are to be used on the half-connection.
Otherwise, it is NULL (due to dccp_init_sock/dccp_create_openreq_child),
so that the test is a valid one.
The activation handler for Ack Vectors is called as soon as the feature
negotiation has concluded at the
* server when the Ack marking the transition RESPOND => OPEN arrives;
* client after it has sent its ACK, marking the transition REQUEST => PARTOPEN.
Adding the sequence number of the Response packet to the Ack Vector has been
removed, since
(a) connection establishment implies that the Response has been received;
(b) the CCIDs only look at packets received in the (PART)OPEN state, i.e.
this entry will always be ignored;
(c) it can not be used for anything useful - to detect loss for instance, only
packets received after the loss can serve as pseudo-dupacks.
There was a FIXME to change the error code when dccp_ackvec_add() fails.
I removed this after finding out that:
* the check whether ackno < ISN is already made earlier,
* this Response is likely the 1st packet with an Ackno that the client gets,
* so when dccp_ackvec_add() fails, the reason is likely not a packet error.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk> Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz> Signed-off-by: David S. Miller <davem@davemloft.net>
Gerrit Renker [Mon, 8 Dec 2008 09:18:37 +0000 (01:18 -0800)]
dccp: Remove manual influence on NDP Count feature
Updating the NDP count feature is handled automatically now:
* for CCID-2 it is disabled, since the code does not use NDP counts;
* for CCID-3 it is enabled, as NDP counts are used to determine loss lengths.
Allowing the user to change NDP values leads to unpredictable and failing
behaviour, since it is then possible to disable NDP counts even when they
are needed (e.g. in CCID-3).
This means that only those user settings are sensible that agree with the
values for Send NDP Count implied by the choice of CCID. But those settings
are already activated by the feature negotiation (CCID dependency tracking),
hence this form of support is redundant.
At startup the initialisation of the NDP count feature uses the default
value of 0, which is done implicitly by the zeroing-out of the socket when
it is allocated. If the choice of CCID or feature negotiation enables NDP
count, this will then be updated via the NDP activation handler.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk> Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz> Signed-off-by: David S. Miller <davem@davemloft.net>
Gerrit Renker [Mon, 8 Dec 2008 09:18:05 +0000 (01:18 -0800)]
dccp: Remove obsolete parts of the old CCID interface
The TX/RX CCIDs of the minisock are now redundant: similar to the Ack Vector
case, their value equals initially that of the sysctl, but at the end of
feature negotiation may be something different.
The old interface removed by this patch thus has been replaced by the newer
interface to dynamically query the currently loaded CCIDs.
Also removed are the constructors for the TX CCID and the RX CCID, since the
switch "rx <-> non-rx" is done by the handler in minisocks.c (and the handler
is the only place in the code where CCIDs are loaded).
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk> Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz> Signed-off-by: David S. Miller <davem@davemloft.net>
Gerrit Renker [Mon, 8 Dec 2008 09:17:32 +0000 (01:17 -0800)]
dccp: Clean up old feature-negotiation infrastructure
The code removed by this patch is no longer referenced or used, the added
lines update documentation and copyrights.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk> Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz> Signed-off-by: David S. Miller <davem@davemloft.net>
Gerrit Renker [Mon, 8 Dec 2008 09:16:27 +0000 (01:16 -0800)]
dccp: Integration of dynamic feature activation - part 3 (client side)
This integrates feature-activation in the client:
1. When dccp_parse_options() fails, the reset code is already set; request_sent\
_state_process() currently overrides this with `Packet Error', which is not
intended - changed to use the reset code supplied by dccp_parse_options().
2. When feature negotiation fails, the socket should be marked as not usable,
so that the application is notified that an error occurred. This is achieved
by a new label 'unable_to_proceed': generating an error code of `Aborted',
setting the socket state to CLOSED, returning with ECOMM in sk_err.
3. Avoids parsing the Ack twice in Respond state by not doing option processing
again in dccp_rcv_respond_partopen_state_process (as option processing has
already been done on the request_sock in dccp_check_req).
Since this addresses congestion-control initialisation, a corresponding
FIXME has been removed.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk> Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz> Signed-off-by: David S. Miller <davem@davemloft.net>
Gerrit Renker [Mon, 8 Dec 2008 09:15:55 +0000 (01:15 -0800)]
dccp: Integration of dynamic feature activation - part 2 (server side)
This patch integrates the activation of features at the end of negotiation
into the server-side code.
Note regarding the removal of 'const':
--------------------------------------
The 'const' attribute has been removed from 'dreq' since dccp_activate_values()
needs to operate on dreq's feature list. Part of the activation is to remove
those options from the list that have already been confirmed, hence it is not
purely read-only.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk> Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz> Signed-off-by: David S. Miller <davem@davemloft.net>
Gerrit Renker [Mon, 8 Dec 2008 09:15:26 +0000 (01:15 -0800)]
dccp: Integration of dynamic feature activation - part 1 (socket setup)
This first patch out of three replaces the hardcoded default settings with
initialisation code for the dynamic feature negotiation.
The patch also ensures that the client feature-negotiation queue is flushed
only when entering the OPEN state.
Since confirmed Change options are removed as soon as they are confirmed
(in the DCCP-Response), this ensures that Confirm options are retransmitted.
Note on retransmitting Confirm options:
---------------------------------------
Implementation experience showed that it is necessary to retransmit Confirm
options. Thanks to Leandro Melo de Sales who reported a bug in an earlier
revision of the patch set, resulting from not retransmitting these options.
As long as the client is in PARTOPEN, it needs to retransmit the Confirm
options for the Change options received on the DCCP-Response from the server.
Otherwise, if the packet containing the Confirm options gets dropped in the
network, the connection aborts due to undefined feature negotiation state.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk> Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz> Signed-off-by: David S. Miller <davem@davemloft.net>
Wang Chen [Mon, 8 Dec 2008 09:14:16 +0000 (01:14 -0800)]
netdevice: Kill netdev->priv
This is the last shoot of this series.
After I removing all directly reference of netdev->priv, I am killing
"priv" of "struct net_device" and fixing relative comments/docs.
Anyone will not be allowed to reference netdev->priv directly.
If you want to reference the memory of private data, use netdev_priv()
instead.
If the private data is not allocted when alloc_netdev(), use
netdev->ml_priv to point that memory after you creating that private
data.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Wang Chen [Mon, 8 Dec 2008 09:13:25 +0000 (01:13 -0800)]
staging-winbond: Kill directly reference of netdev->priv
This driver is not yet finished.
At this time, we don't know how netdev be created and how
private data be allocated.
So, simply use netdev_priv() now and leave some temp comment.
Compile test only.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Wang Chen [Sun, 7 Dec 2008 07:58:37 +0000 (23:58 -0800)]
staging-p80211: Kill directly reference of netdev->priv
In this driver, netdev's private data is wlandevice_t. And the
wlandev(type of wlandevice_t) is exist before netdev be allocated. So
use netdev->ml_priv to point to the private data.
I am not sure whether I should consider the kernel version older than
2.3.38. Because in those kernels, netdevice_t is "structure dev"
instead of "structure net_device" and of course "dev->ml_priv" will
cause compile error. But before my patch, in function wlan_setup(),
there is a ether_setup(net_device) which already broke kernels which
older than 2.3.38.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com> Acked-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Wang Chen [Sun, 7 Dec 2008 07:57:49 +0000 (23:57 -0800)]
s390_net: Kill directly reference of netdev->priv
The private data comes from ccwgroup_device.
So just don't allocate private data memory when do alloc_netdev()
and use netdev->ml_priv to reference private data.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ilpo Järvinen [Sat, 6 Dec 2008 06:49:37 +0000 (22:49 -0800)]
tcp: fix tso_should_defer in 64bit
Since jiffies is unsigned long, the types get expanded into
that and after long enough time the difference will therefore
always be > 1 (and that probably happens near boot as well as
iirc the first jiffies wrap is scheduler close after boot to
find out problems related to that early).
This was originally noted by Bill Fink in Dec'07 but nobody
never ended fixing it.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi> Signed-off-by: David S. Miller <davem@davemloft.net>
Ilpo Järvinen [Sat, 6 Dec 2008 06:42:22 +0000 (22:42 -0800)]
tcp: introduce struct tcp_sacktag_state to reduce arg pressure
There are just too many args to some sacktag functions. This
idea was first proposed by David S. Miller around a year ago,
and the current situation is much worse that what it was back
then.
tcp_sacktag_one can be made a bit simpler by returning the
new sacked (it can be achieved with a single variable though
the previous code "caching" sacked into a local variable and
therefore it is not exactly equal but the results will be the
same).
Ilpo Järvinen [Sat, 6 Dec 2008 06:41:26 +0000 (22:41 -0800)]
tcp: make mtu probe failure to not break gso'ed skbs unnecessarily
I noticed that since skb->len has nothing to do with actual segment
length with gso, we need to figure it out separately, reuse
a function from the recent shifting stuff (generalize it).
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Fri, 5 Dec 2008 23:08:03 +0000 (15:08 -0800)]
igb/e1000e: Naming interrupt vectors
Change interrupt vector naming to match recent changes from Robert Olsson.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Acked-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
ath9k: Use GFP_ATOMIC when allocating TX private area
Using GFP_KERNEL was wrong and produces a 'scheduling while atomic'
bug as we're in a tasklet. Also, check for proper return values
now, in case allocation fails and be sure to stop the TX queue
in case of memory issues but gaurantee the TX queue will
eventually be woken up.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com> Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Wed, 3 Dec 2008 16:29:48 +0000 (17:29 +0100)]
rt2x00: Move crypto TX descriptor handling to rt2x00crypto.c
Move all code which determines the right TX descriptor
fields specific to crypto support into rt2x00crypto.c.
This makes the code in rt2x00queue more simpler and
better concentrates all crypto code into a single location.
With this we can also remove some ifdefs in rt2x00queue.c
since the code inside the ifdef is either very small, or
only calling empty functions (see empty function definitions
in rt2x00lib.h).
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Wed, 3 Dec 2008 16:29:21 +0000 (17:29 +0100)]
rt2x00: Fix check for BSS info changes
Fix ERP configuration, due to a too strict changes
flags checking we never updated the short slot time
or basic rate mask when no other changes were made
at the same time.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Tue, 2 Dec 2008 21:50:33 +0000 (22:50 +0100)]
rt2x00: Add RXDONE_CRYPTO_IV/ICV flags
Drivers should notify rt2x00lib when they provide
the IV/ICV data. This adds some flexibility to drivers
which can't provide all information.
* rt2500usb provides ICV inside the frame
* rt2800pci doesn't provide IV/ICV
* rt2800usb doesn't provide IV/ICV
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwl3945 : Fix a-band association for passive channels
Patch does following things
1) This patch fixes the a-band association for passive channels with new
uCode feature that it allows direct scan on passive channels after
auto-switch from passive to active. This enables sending of direct probes
on passive channels, as long as some traffic is detected on that channel.
This improves the scanning for hidden SSIDs in A-band,which is all
passive channels.
2) This fix will only work with uCode version 15.28.2.8 and above.
Prior versions of uCode would work only if we heard the traffic within
active dwell time, which is much shorter than passive dwell time and
is shorter than typical beacon periods. This patch also provids full
active dwell time even if we hear traffic late in passive dwell.
3) uCode API version is incremented to 2.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Acked-by: Ben Cahill <ben.m.cahill@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reinette Chatre [Tue, 2 Dec 2008 20:14:06 +0000 (12:14 -0800)]
iwlwifi: rely on API version read from firmware
This adds the infrastructure to support older firmware APIs.
The API version number is stored as part of the filename, we first try to
load the most recent firmware and progressively try lower versions.
The API version is also read from the firmware self and stored as part
of the iwl_priv structure. Only firmware that is supported by driver will
be loaded. The version number read from firmware is compared
to supported versions in the driver not the API version used as part of
filename.
An example using this new infrastrucure:
if (IWL_UCODE_API(priv->ucode_ver) >= 2) {
Driver interacts with Firmware API version >= 2.
} else {
Driver interacts with Firmware API version 1.
}
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
We store the ucode version number as part of
iwl_priv/iwl3945_priv. This enables us to determine
if particular ucode has support for features in order
to have driver support more than one ucode API.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Zhu Yi [Tue, 2 Dec 2008 20:14:04 +0000 (12:14 -0800)]
iwlwifi: fix DMA channel number in iwl_txq_ctx_stop
The patch fixes the misuse of DMA channel number by Tx queue number in
iwl_tx_ctx_stop().
The problem was originally reported by Wu Fengguang who complains
iwlagn driver takes too long time when issuing `ifconfig wlan0 down`.
The patch now decreases the interface bring down time from 2 seconds
to 0.8 second.
This fixes bugs:
http://bugzilla.kernel.org/show_bug.cgi?id=11956
http://www.intellinuxwireless.org/bugzilla/show_bug.cgi?id=1790
Signed-off-by: Zhu Yi <yi.zhu@intel.com> Tested-by: Fengguang Wu <fengguang.wu@intel.com> Acked-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Abbas, Mohamed [Tue, 2 Dec 2008 20:14:03 +0000 (12:14 -0800)]
iwl3945: Fix iwl3945 rate scaling.
3945 rate scaling was broken in recent tree. This patch fix the following:
1- Get TX response info and update rates window.
2- Rate scaling selection.
3- Flush window timer.
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
projects / linux-beck.git / log