After a newly plugged CPU sets the cpu_online bit it enables
interrupts and goes idle. The cpu which brought up the new cpu waits
for the cpu_online bit and when it observes it, it sets the cpu_active
bit for this cpu. The cpu_active bit is the relevant one for the
scheduler to consider the cpu as a viable target.
With forced threaded interrupt handlers which imply forced threaded
softirqs we observed the following race:
When an interrupt happens before the cpu_active bit is set by the cpu
which brought up the newly onlined cpu, then the scheduler refuses to
enqueue the woken thread which is bound to that newly onlined cpu on
that newly onlined cpu due to the not yet set cpu_active bit and
selects a fallback runqueue. Not really an expected and desirable
behaviour.
So far this has only been observed with forced hard/softirq threading,
but in theory this could happen without forced threaded hard/softirqs
as well. It's probably unobservable as it would take a massive
interrupt storm on the newly onlined cpu which causes the softirq loop
to wake up the softirq thread and an even longer delay of the cpu
which waits for the cpu_online bit.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Peter Zijlstra <peterz@infradead.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/built-in.o: In function `early_init_dt_check_for_initrd':
/home/florian/dev/kernel/x86/linux-2.6-x86/drivers/of/fdt.c:571:
undefined reference to `early_init_dt_setup_initrd_arch'
make: *** [.tmp_vmlinux1] Error 1
which happens as soon as we enable initrd support on a x86 devicetree
platform such as Intel CE4100.
Signed-off-by: Florian Fainelli <ffainelli@freebox.fr> Acked-by: Grant Likely <grant.likely@secretlab.ca> Cc: Maxime Bizon <mbizon@freebox.fr> Acked-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc> Link: http://lkml.kernel.org/r/201106061015.50039.ffainelli@freebox.fr Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Ignacy reports that sometimes after leaving an IBSS
joining a new one didn't work because there still
were stations on the list. He fixed it by flushing
stations when attempting to join a new IBSS, but
this shouldn't be happening in the first case. When
I looked into it I saw a race condition in teardown
that could cause stations to be added after flush,
and thus cause this situation. Ignacy confirms that
after applying my patch he hasn't seen this happen
again.
Reported-by: Ignacy Gawedzki <i@lri.fr> Debugged-by: Ignacy Gawedzki <i@lri.fr> Tested-by: Ignacy Gawedzki <i@lri.fr> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When SR-IOV is enabled, i350 devices fail to pass traffic. This is due to
the driver attempting to enable RSS on the PF device, which is not
supported by the i350.
When max_vfs is specified on an i350 adapter, set the number of RSS queues
to 1.
This issue affects 2.6.39 as well.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Setting tx power can be deferred during scan or changing channel.
If after that correct tx power settings will not be sent to device,
we can observe transmission problems and timeouts. Force to send
tx power settings also after partial rxon change, to assure device
always be configured with up-to-date settings.
This patch fixes 802.11n stability and performance regression we have
since 2.6.35. It boost performance on my 5GHz N-only network from about
5MB/s to 8MB/s. Similar percentage boost can be observed on 2.4 GHz.
These are test results of 5x downloading of approximately 700MB iso
image:
This was achieved with NetworkManager configured to do not perform
periodical scans, by configuring constant BSSID. With periodical scans,
after some time, performance downgrade to unpatched driver level, like
in example below:
However patch still make better here, since similar test on unpatched
driver make link disconnects with below messages after some time:
wlan1: authenticate with 00:23:69:35:d1:3f (try 1)
wlan1: authenticate with 00:23:69:35:d1:3f (try 2)
wlan1: authenticate with 00:23:69:35:d1:3f (try 3)
wlan1: authentication with 00:23:69:35:d1:3f timed out
On 2.6.35 kernel patch helps against connection hangs with messages:
iwlagn 0000:20:00.0: queue 10 stuck 3 time. Fw reload.
iwlagn 0000:20:00.0: On demand firmware reload
iwlagn 0000:20:00.0: Stopping AGG while state not ON or starting
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The lockdep warning below detects a possible A->B/B->A locking
dependency of mm->mmap_sem and dcookie_mutex. The order in
sync_buffer() is mm->mmap_sem/dcookie_mutex, while in
sys_lookup_dcookie() it is vice versa.
Fixing it in sys_lookup_dcookie() by unlocking dcookie_mutex before
copy_to_user().
oprofiled/4432 is trying to acquire lock:
(&mm->mmap_sem){++++++}, at: [<ffffffff810b444b>] might_fault+0x53/0xa3
but task is already holding lock:
(dcookie_mutex){+.+.+.}, at: [<ffffffff81124d28>] sys_lookup_dcookie+0x45/0x149
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
This fixes the A->B/B->A locking dependency, see the warning below.
The function task_exit_notify() is called with (task_exit_notifier)
.rwsem set and then calls sync_buffer() which locks buffer_mutex. In
sync_start() the buffer_mutex was set to prevent notifier functions to
be started before sync_start() is finished. But when registering the
notifier, (task_exit_notifier).rwsem is locked too, but now in
different order than in sync_buffer(). In theory this causes a locking
dependency, what does not occur in practice since task_exit_notify()
is always called after the notifier is registered which means the lock
is already released.
However, after checking the notifier functions it turned out the
buffer_mutex in sync_start() is unnecessary. This is because
sync_buffer() may be called from the notifiers even if sync_start()
did not finish yet, the buffers are already allocated but empty. No
need to protect this with the mutex.
So we fix this theoretical locking dependency by removing buffer_mutex
in sync_start(). This is similar to the implementation before commit:
750d857 oprofile: fix crash when accessing freed task structs
which introduced the locking dependency.
Lockdep warning:
oprofiled/4447 is trying to acquire lock:
(buffer_mutex){+.+...}, at: [<ffffffffa0000e55>] sync_buffer+0x31/0x3ec [oprofile]
but task is already holding lock:
((task_exit_notifier).rwsem){++++..}, at: [<ffffffff81058026>] __blocking_notifier_call_chain+0x39/0x67
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
Reported-by: Marcin Slusarz <marcin.slusarz@gmail.com> Cc: Carl Love <carll@us.ibm.com> Signed-off-by: Robert Richter <robert.richter@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
After registering the task free notifier we possibly have tasks in our
dying_tasks list. Free them after unregistering the notifier in case
of an error.
Signed-off-by: Robert Richter <robert.richter@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
BugLink: https://launchpad.net/bugs/792712
The original reporter states that sound from the internal speakers is
inaudible until using the model=auto quirk. This symptom is due to an
existing quirk mask for 0x102802b* that uses the model=dell quirk. To
limit the possible regressions, leave the existing quirk mask but add
a higher priority specific mask for the reporter's PCI SSID.
Reported-and-tested-by: rodni hipp Signed-off-by: Daniel T Chen <crimsun@ubuntu.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently it is possible that snd_soc_new_{mixer,mux,pga} is called with a
DAPM context not matching the widgets context. This can lead to a wrong
prefix_len calculation, which will result in undefined behaviour. To avoid
this always use the DAPM context from the widget itself.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It's possible for the following set of events to happen:
cifsd calls cifs_reconnect which reconnects the socket. A userspace
process then calls cifs_negotiate_protocol to handle the NEGOTIATE and
gets a reply. But, while processing the reply, cifsd calls
cifs_reconnect again. Eventually the GlobalMid_Lock is dropped and the
reply from the earlier NEGOTIATE completes and the tcpStatus is set to
CifsGood. cifs_reconnect then goes through and closes the socket and sets the
pointer to zero, but because the status is now CifsGood, the new socket
is not created and cifs_reconnect exits with the socket pointer set to
NULL.
Fix this by only setting the tcpStatus to CifsGood if the tcpStatus is
CifsNeedNegotiate, and by making sure that generic_ip_connect is always
called at least once in cifs_reconnect.
Note that this is not a perfect fix for this issue. It's still possible
that the NEGOTIATE reply is handled after the socket has been closed and
reconnected. In that case, the socket state will look correct but it no
NEGOTIATE was performed on it be for the wrong socket. In that situation
though the server should just shut down the socket on the next attempted
send, rather than causing the oops that occurs today.
Reported-and-Tested-by: Ben Greear <greearb@candelatech.com> Signed-off-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Steve French <sfrench@us.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
AppArmor may do a GFP_KERNEL memory allocation with task_lock(tsk->group_leader);
held when called from security_task_setrlimit. This will only occur when the
task's current policy has been replaced, and the task's creds have not been
updated before entering the LSM security_task_setrlimit() hook.
BUG: sleeping function called from invalid context at mm/slub.c:847
in_atomic(): 1, irqs_disabled(): 0, pid: 1583, name: cupsd
2 locks held by cupsd/1583:
#0: (tasklist_lock){.+.+.+}, at: [<ffffffff8104dafa>] do_prlimit+0x61/0x189
#1: (&(&p->alloc_lock)->rlock){+.+.+.}, at: [<ffffffff8104db2d>]
do_prlimit+0x94/0x189
Pid: 1583, comm: cupsd Not tainted 3.0.0-rc2-git1 #7
Call Trace:
[<ffffffff8102ebf2>] __might_sleep+0x10d/0x112
[<ffffffff810e6f46>] slab_pre_alloc_hook.isra.49+0x2d/0x33
[<ffffffff810e7bc4>] kmem_cache_alloc+0x22/0x132
[<ffffffff8105b6e6>] prepare_creds+0x35/0xe4
[<ffffffff811c0675>] aa_replace_current_profile+0x35/0xb2
[<ffffffff811c4d2d>] aa_current_profile+0x45/0x4c
[<ffffffff811c4d4d>] apparmor_task_setrlimit+0x19/0x3a
[<ffffffff811beaa5>] security_task_setrlimit+0x11/0x13
[<ffffffff8104db6b>] do_prlimit+0xd2/0x189
[<ffffffff8104dea9>] sys_setrlimit+0x3b/0x48
[<ffffffff814062bb>] system_call_fastpath+0x16/0x1b
Signed-off-by: John Johansen <john.johansen@canonical.com> Reported-by: Miles Lane <miles.lane@gmail.com> Signed-off-by: James Morris <jmorris@namei.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Full-speed isoc endpoints specify interval in exponent based form in
frames, not microframes, so we need to adjust accordingly.
NEC xHCI host controllers will return an error code of 0x11 if a full
speed isochronous endpoint is added with the Interval field set to
something less than 3 (2^3 = 8 microframes, or one frame). It is
impossible for a full speed device to have an interval smaller than one
frame.
This was always an issue in the xHCI driver, but commit dfa49c4ad120a784ef1ff0717168aa79f55a483a "USB: xhci - fix math in
xhci_get_endpoint_interval()" removed the clamping of the minimum value
in the Interval field, which revealed this bug.
This needs to be backported to stable kernels back to 2.6.31.
Reported-by: Matt Evans <matt@ozlabs.org> Signed-off-by: Dmitry Torokhov <dtor@vmware.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some Fresco Logic hosts, including those found in the AUAU N533V laptop,
advertise MSI, but fail to actually generate MSI interrupts. Add a new
xHCI quirk to skip MSI enabling for the Fresco Logic host controllers.
Fresco Logic confirms that all chips with PCI vendor ID 0x1b73 and device
ID 0x1000, regardless of PCI revision ID, do not support MSI.
This should be backported to stable kernels as far back as 2.6.36, which
was the first kernel to support MSI on xHCI hosts.
xHCI controllers respond to a Reset Device command when the Slot is in the
Enabled/Disabled state by returning an error. This is fine on other host
controllers, but the Etron xHCI host controller returns a vendor-specific
error code that the xHCI driver doesn't understand. The xHCI driver then
gives up on device enumeration.
Instead of issuing a command that will fail, just return. This fixes the
issue with the xhci driver not working on ASRock P67 Pro/Extreme boards.
This should be backported to stable kernels as far back as 2.6.34.
It breaks some people's machines, so this will all get worked out in the
3.0 kernel release, it's not quite ready for 2.6.39 just yet.
Thanks to Maarten Lankhorst <m.b.lankhorst@gmail.com> for reporting the
issue.
Cc: Maarten Lankhorst <m.b.lankhorst@gmail.com> Cc: Jim Bos <jim876@xs4all.nl> Cc: Matthew Garrett <mjg@redhat.com> Cc: H. Peter Anvin <hpa@linux.intel.com> Cc: Tony Luck <tony.luck@intel.com> Cc: Yinghai Lu <yinghai@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some USB mass-storage devices have bugs that cause them not to handle
the first READ(10) command they receive correctly. The Corsair
Padlock v2 returns completely bogus data for its first read (possibly
it returns the data in encrypted form even though the device is
supposed to be unlocked). The Feiya SD/SDHC card reader fails to
complete the first READ(10) command after it is plugged in or after a
new card is inserted, returning a status code that indicates it thinks
the command was invalid, which prevents the kernel from retrying the
read.
Since the first read of a new device or a new medium is for the
partition sector, the kernel is unable to retrieve the device's
partition table. Users have to manually issue an "hdparm -z" or
"blockdev --rereadpt" command before they can access the device.
This patch (as1470) works around the problem. It adds a new quirk
flag, US_FL_INVALID_READ10, indicating that the first READ(10) should
always be retried immediately, as should any failing READ(10) commands
(provided the preceding READ(10) command succeeded, to avoid getting
stuck in a loop). The patch also adds appropriate unusual_devs
entries containing the new flag.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Tested-by: Sven Geggus <sven-usbst@geggus.net> Tested-by: Paul Hartman <paul.hartman+linux@gmail.com> CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Protocol stall should not be fatal while reading port or hub status as it is
transient state. Currently hub EP0 STALL during port status read results in
failed device enumeration. This has been observed with ST-Ericsson (formerly
Philips) USB 2.0 Hub (04cc:1521) after connecting keyboard.
The funtion option_send_status times out when sending USB messages
to the interfaces 0, 1, and 2 of this UMTS stick. This results in a
5s timeout in the function causing other tty operations to feel very
sluggish.
This patch adds a blacklist entry for these 3 interfaces on the ZTE
K3765-Z device.
I was also able to reproduce the problem with v2.6.38 and v2.6.39.
This modem really wants sendsetup blacklisted for interfaces 0 and 1,
otherwise the kernel hardlocks for about 10 seconds while waiting for
the modem's firmware to respond, which it of course doesn't do.
A slight complication here is that TCT (who owns the Alcatel brand) used
the same USB IDs for the X200 as the X060s despite the devices having
completely different firmware and AT command sets, so we end up adding
the X060s to the blacklist at the same time. PSA to OEMs: don't use the
same USB IDs for different devices. Really. It makes your kittens cry.
Signed-off-by: Dan Williams <dcbw@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Unconditionally changing the address limit to USER_DS and not restoring
it to its old value in the error path is wrong because it prevents us
using kernel memory on repeated calls to this function. This, in fact,
breaks the fallback of hard coded paths to the init program from being
ever successful if the first candidate fails to load.
With this patch applied switching to USER_DS is delayed until the point
of no return is reached which makes it possible to have a multi-arch
rootfs with one arch specific init binary for each of the (hard coded)
probed paths.
Since the address limit is already set to USER_DS when start_thread()
will be invoked, this redundancy can be safely removed.
Many Linux distributions would enable vesafb in order to display
early stage boot splash. In this case, we will get garbled X
Window screen if running X fbdev on psbfb.
This is because fb0 is occupied by vesafb while psbfb is on fb1.
They tried to drive the same pieces of hardware at the same
time. With unmodified X start-up, it would try to use default
fb0 framebuffer device and unfortunately it is now broken
becaues fb1 supersedes it.
We should let psbfb takeover framebuffer control from vesafb
to get around this problem.
This adds the Nokia E7 and C7 to the list of devices in cdc-acm, allowing
the secondary ACM channel on the device to be exposed. Without this patch
the ACM driver won't claim this secondary channel as it's marked as
having a vendor-specific protocol.
Some PCIe cards ship with a PCI-PCIe bridge which is not
visible as a PCI device in Linux. But the device-id of the
bridge is present in the IOMMU tables which causes a boot
crash in the IOMMU driver.
This patch fixes by removing these cards from the IOMMU
handling. This is a pure -stable fix, a real fix to handle
this situation appriatly will follow for the next merge
window.
The driver contains several loops counting on an u16 value
where the exit-condition is checked against variables that
can have values up to 0xffff. In this case the loops will
never exit. This patch fixed 3 such loops.
Unfortunatly there are systems where the AMD IOMMU does not
cover all devices. This breaks with the current driver as it
initializes the global dma_ops variable. This patch limits
the AMD IOMMU to the devices listed in the IVRS table fixing
DMA for devices not covered by the IOMMU.
The find_next_zero_bit() is called with the from and to arguments in the
wrong order. This results in the function always returning 0, and all
media devices being registered with minor 0. Furthermore, mdev->minor is
then used before being assigned with the find_next_zero_bit() return
value. This really makes sure we'll always use minor 0.
Fix this and let the system support more than one media device.
When signing is enabled, the first session that's established on a
socket will cause a printk like this to pop:
CIFS VFS: Unexpected SMB signature
This is because the key exchange hasn't happened yet, so the signature
field is bogus. Don't try to check the signature on the socket until the
first session has been established. Also, eliminate the specific check
for SMB_COM_NEGOTIATE since this check covers that case too.
Cc: Shirish Pargaonkar <shirishpargaonkar@gmail.com> Signed-off-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Steve French <sfrench@us.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The genirq changes are initializing descriptors for sparse IRQs quite
differently from how non-sparse (stacked?) IRQs are initialized, with
the effect that on my platform all IRQs are default-disabled on sparse
IRQs and default-enabled if non-sparse IRQs are used, crashing some
GPIO driver.
Fix this by refactoring the non-sparse IRQs to use the same descriptor
init function as the sparse IRQs.
Since fb_info is now refcounted and thus may get freed at any time it
gets unregistered module unloading will try to unregister framebuffer
as stored in platform data on probe though this pointer may
be stale.
Cleanup platform data on framebuffer release.
Signed-off-by: Bruno Prémont <bonbons@linux-vserver.org> Signed-off-by: Paul Mundt <lethal@linux-sh.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On my x86_64 system with >4GB of ram and swiotlb instead of
a hardware iommu (because I have a VIA chipset), the call
to pci_set_dma_mask (see below) with 40bits returns an error.
But it seems that the radeon driver is designed to have
need_dma32 = true exactly if pci_set_dma_mask is called
with 32 bits and false if it is called with 40 bits.
I have read somewhere that the default are 32 bits. So if the
call fails I suppose that need_dma32 should be set to true.
And indeed the patch fixes the problem I have had before
and which I had described here:
http://choon.net/forum/read.php?21,106131,115940
Acked-by: Alex Deucher <alexdeucher@gmail.com> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I found this while figuring out why gnome-shell would not run on my
Asus EeeBox PC EB1007. As a standalone "pc" this device cleary does not have
an internal panel, yet it claims it does. Add a quirk to fix this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Keith Packard <keithp@keithp.com> Signed-off-by: Keith Packard <keithp@keithp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The main lock_is_held() user is lockdep_assert_held(), avoid false
assertions in lockdep_off() sections by unconditionally reporting the
lock is taken.
[ the reason this is important is a lockdep_assert_held() in ttwu()
which triggers a warning under lockdep_off() as in printk() which
can trigger another wakeup and lock up due to spinlock
recursion, as reported and heroically debugged by Arne Jansen ]
cdc_ncm 2-1.4:1.6: no reset_resume for driver cdc_ncm?
cdc_ncm 2-1.4:1.7: no reset_resume for driver cdc_ncm?
cdc_ncm 2-1.4:1.6: usb0: unregister 'cdc_ncm' usb-0000:00:1d.0-1.4, CDC NCM
This is important for the Ericsson F5521gw GSM/UMTS modem.
Otherwise modemmanager looses the fact that the cdc_ncm and cdc_acm devices
belong together.
The cdc_ether module does the same.
Signed-off-by: Stefan Metzmacher <metze@samba.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In both trigger_scan and sched_scan operations, we were checking for
the SSID length before assigning the value correctly. Since the
memory was just kzalloc'ed, the check was always failing and SSID with
over 32 characters were allowed to go through.
This was causing a buffer overflow when copying the actual SSID to the
proper place.
This bug has been there since 2.6.29-rc4.
Signed-off-by: Luciano Coelho <coelho@ti.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit 69e3cea8d5fd526 ("powerpc/smp: Make start_secondary_resume
available to all CPU variants") introduced start_secondary_resume to
misc_32.S, however it uses a 64-bit instruction which is not valid on
32-bit platforms. Use 'stw' instead.
Reported-by: Richard Cochran <richardcochran@gmail.com> Tested-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The following patch sets the MaxPayload setting to match the parent
reading when inserting a PCIE card into a hotplug slot. On our system,
the upstream bridge is set to 256, but when inserting a card, the card
setting defaults to 128. As soon as I/O is performed to the card it
starts receiving errors since the payload size is too small.
Now, uart_update_termios is empty, so it's time to remove it. We no
longer need a live tty in .dtr_rts. So this should prune all the bugs
where tty is zeroed in port->tty during tty_port_block_til_ready.
There is one thing to note. We don't set ASYNC_NORMAL_ACTIVE now. It's
because this is done already in tty_port_block_til_ready.
In .dtr_rts we do:
uart_set_mctrl(uport, TIOCM_DTR | TIOCM_RTS)
and call uart_update_termios. It does:
uart_set_mctrl(port, TIOCM_DTR | TIOCM_RTS)
once again. As the only callsite of uart_update_termios is .dtr_rts,
remove the uart_set_mctrl from uart_update_termios to not set it twice.
We should not fiddle with speed and cflags in .dtr_rts hook. Actually
we might not have tty at that moment already.
So move the console cflag copy and speed setup into uart_startup.
Actually the speed setup is already there, but we need to call it
unconditionally (uart_startup is called from uart_open with hw_init =
0).
This means we move uart_change_speed before dtr/rts setup in .dtr_rts.
But this should not matter as the setup should be called after
uart_change_speed anyway.
Before: After:
dtr/rts setup (dtr_rts) uart_change_speed (startup)
uart_change_speed (update_termios) dtr/rts setup (dtr_rts)
dtr/rts setup (update_termios) dtr/rts setup (update_termios)
The second setup will dismiss with the next patch.
Al Viro observes that in the hugetlb case, handle_mm_fault() may return
a value of the kind ENOSPC when its caller is expecting a value of the
kind VM_FAULT_SIGBUS: fix alloc_huge_page()'s failure returns.
zd1211 devices register 'EP 4 OUT' endpoint as Interrupt type on USB 2.0:
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x04 EP 4 OUT
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 1
However on USB 1.1 endpoint becomes Bulk:
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x04 EP 4 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Problem here is that usb_bulk_msg() on interrupt endpoint selfcorrects the
call and changes requested pipe to interrupt type (see usb_bulk_msg).
However with usb_interrupt_msg() on bulk endpoint does not correct the
pipe type to bulk, but instead URB is submitted with interrupt type pipe.
So pre-2.6.39 used usb_bulk_msg() and therefore worked with both endpoint
types, however in 2.6.39 usb_interrupt_msg() with bulk endpoint causes
ohci_hcd to fail submitted URB instantly with -ENOSPC and preventing zd1211rw
from working with OHCI.
Fix this by detecting endpoint type and using correct endpoint/pipe types
for URB. Also fix asynchronous zd_usb_iowrite16v_async() to use right
URB type on 'EP 4 OUT'.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In some cases we can read wrong temperature value. If after that
temperature value will not be updated to good one, we badly configure
tx power parameters and device is unable to send a data.
The current temperature range check of MSR_IA32_TEMPERATURE_TARGET
seems too strict to me, some TjMax values documented in
Documentation/hwmon/coretemp wouldn't pass. Relax the check so that
all the documented values pass.
Commit a321cedb12904114e2ba5041a3673ca24deb09c9 excludes CPU models 0xe, 0xf,
0x16, and 0x1a from TjMax temperature adjustment, even though several of those
CPUs are known to have TiMax other than 100 degrees C, and even though the code
in adjust_tjmax() explicitly handles those CPUs and points to a Web document
listing several of the affected CPU IDs.
Reinstate original TjMax adjustment if TjMax can not be determined using the
IA32_TEMPERATURE_TARGET register.
https://bugzilla.kernel.org/show_bug.cgi?id=32582
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com> Cc: Huaxu Wan <huaxu.wan@linux.intel.com> Cc: Carsten Emde <C.Emde@osadl.org> Cc: Valdis Kletnieks <valdis.kletnieks@vt.edu> Cc: Henrique de Moraes Holschuh <hmh@hmh.eng.br> Cc: Yong Wang <yong.y.wang@linux.intel.com> Cc: Rudolf Marek <r.marek@assembler.cz> Cc: Fenghua Yu <fenghua.yu@intel.com> Tested-by: Jean Delvare <khali@linux-fr.org> Acked-by: Jean Delvare <khali@linux-fr.org> Acked-by: Fenghua Yu <fenghua.yu@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The ath9k driver subtracts 3 dBm to the txpower as with two radios the
signal power is doubled.
The resulting value is assigned in an u16 which overflows and makes
the card work at full power.
in two more places. I grepped the ath tree and didn't find any others.
Signed-off-by: Daniel Halperin <dhalperi@cs.washington.edu> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Whenever there is a channel width change from 40 Mhz to 20 Mhz,
the hardware is reconfigured to ht20. Meantime before doing
the rate control updation, the packets are being transmitted are
selected rate with IEEE80211_TX_RC_40_MHZ_WIDTH.
While transmitting ht40 rate packets in ht20 mode is causing
baseband panic with AR9003 based chips.
In certain circumstances, we can get an oops from a torn down device.
Most notably this is from CD roms trying to call scsi_ioctl. The root
cause of the problem is the fact that after scsi_remove_device() has
been called, the queue is fully torn down. This is actually wrong
since the queue can be used until the sdev release function is called.
Therefore, we add an extra reference to the queue which is released in
sdev->release, so the queue always exists.
The 'max_part' parameter controls the number of maximum partition
a nbd device can have. However if a user specifies very large
value it would exceed the limitation of device minor number and
can cause a kernel oops (or, at least, produce invalid device
nodes in some cases).
In addition, specifying large 'nbds_max' value causes same
problem for the same reason.
On my desktop, following command results to the kernel bug:
d4dc210f69 (block: don't block events on excl write for non-optical
devices) added dereferencing of bdev->bd_disk to test
GENHD_FL_BLOCK_EVENTS_ON_EXCL_WRITE; however, bdev->bd_disk can be
%NULL if open failed which can lead to an oops.
Test the flag after testing open was successful, not before.
Signed-off-by: Tejun Heo <tj@kernel.org> Reported-by: David Miller <davem@davemloft.net> Tested-by: David Miller <davem@davemloft.net> Signed-off-by: Jens Axboe <jaxboe@fusionio.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
UBIFS leaks memory on error path in 'ubifs_jnl_update()' in case of write
failure because it forgets to free the 'struct ubifs_dent_node *dent' object.
Although the object is small, the alignment can make it large - e.g., 2KiB
if the min. I/O unit is 2KiB.
Sometimes VM asks the shrinker to return amount of objects it can shrink,
and we return the ubifs_clean_zn_cnt in that case. However, it is possible
that this counter is negative for a short period of time, due to the way
UBIFS TNC code updates it. And I can observe the following warnings sometimes:
shrink_slab: ubifs_shrinker+0x0/0x2b7 [ubifs] negative objects to delete nr=-8541616642706119788
This patch makes sure UBIFS never returns negative count of objects.
commit c56e58537d504706954a06570b4034c04e5b7500 breaks SMP support in PPC_47x chip.
secondary_ti must be set to current thread info before callin kick_cpu or else
start_secondary_47x will jump into void when trying to return to c-code.
In the current setup secondary_ti is initialized before the CPU idle task is started
and only the boot core will start. I am not sure this is the correct solution, but it
makes SMP possible in my chip.
Note! The HOTPLUG support probably need some fixing to, There is no trampoline code
available in head_44x.S - start_secondary_resume?
The comment in domain_remove_one_dev_info() states "No need to compare
PCI domain; it has to be the same". But for the si_domain that isn't
going to be true, as it consists of all the PCI devices that are
identity mapped thus multiple PCI domains can be in si_domain. The
code needs to validate the PCI domain too.
Signed-off-by: Mike Habeck <habeck@sgi.com> Signed-off-by: Mike Travis <travis@sgi.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When using the 1:1 (identity) PCI DMA remapping, PCI Host Bridge devices
that do not use the IOMMU causes a kernel panic. Fix that by not
inserting those devices into the si_domain.
Signed-off-by: Mike Travis <travis@sgi.com> Reviewed-by: Mike Habeck <habeck@sgi.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The __intel_map_single function is not honoring the passed in DMA mask.
This results in not using the coherent DMA mask when called from
intel_alloc_coherent().
Signed-off-by: Mike Travis <travis@sgi.com> Acked-by: Chris Wright <chrisw@sous-sol.org> Reviewed-by: Mike Habeck <habeck@sgi.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Mike Travis and Mike Habeck reported an issue where iova allocation
would return a range that was larger than a device's dma mask.
https://lkml.org/lkml/2011/3/29/423
The dmar initialization code will reserve all PCI MMIO regions and copy
those reservations into a domain specific iova tree. It is possible for
one of those regions to be above the dma mask of a device. It is typical
to allocate iovas with a 32bit mask (despite device's dma mask possibly
being larger) and cache the result until it exhausts the lower 32bit
address space. Freeing the iova range that is >= the last iova in the
lower 32bit range when there is still an iova above the 32bit range will
corrupt the cached iova by pointing it to a region that is above 32bit.
If that region is also larger than the device's dma mask, a subsequent
allocation will return an unusable iova and cause dma failure.
Simply don't cache an iova that is above the 32bit caching boundary.
Reported-by: Mike Travis <travis@sgi.com> Reported-by: Mike Habeck <habeck@sgi.com> Acked-by: Mike Travis <travis@sgi.com> Tested-by: Mike Habeck <habeck@sgi.com> Signed-off-by: Chris Wright <chrisw@sous-sol.org> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When there are a large count of PCI devices, and the pass through
option for iommu is set, much time is spent in the identity_mapping
function hunting though the iommu domains to check if a specific
device is "identity mapped".
Speed up the function by checking the cached info to see if
it's mapped to the static identity domain.
Signed-off-by: Mike Travis <travis@sgi.com> Reviewed-by: Mike Habeck <habeck@sgi.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The identity mapping code appears to make the assumption that if the
devices dma_mask is greater than 32bits the device can use identity
mapping. But that is not true: take the case where we have a 40bit
device in a 44bit architecture. The device can potentially receive a
physical address that it will truncate and cause incorrect addresses
to be used.
Instead check to see if the device's dma_mask is large enough
to address the system's dma_mask.
Signed-off-by: Mike Travis <travis@sgi.com> Reviewed-by: Mike Habeck <habeck@sgi.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit a97590e5 added unlinking domains from iommus to reciprocate the
iommu from domains unlinking that was already done. We actually want
to only do this for device domains and never for the static
identity map domain or VM domains. The SI domain is special and
never freed, while VM domain->id lives in their own special address
space, separate from iommu->domain_ids.
In the current code, a VM can get domain->id zero, then mark that
domain unused when unbound from pci-stub. This leads to DMAR
write faults when the device is re-bound to the host driver.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We typically batch unmaps to be lazily flushed out at
regular intervals. When we destroy a domain, we need
to force a flush of these lazy unmaps to be sure none
reference the domain we're about to free.
Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=35062 Signed-off-by: Alex Williamson <alex.williamson@redhat.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When invalid parameters are passed to apparmor_setprocattr a NULL deref
oops occurs when it tries to record an audit message. This is because
it is passing NULL for the profile parameter for aa_audit. But aa_audit
now requires that the profile passed is not NULL.
Fix this by passing the current profile on the task that is trying to
setprocattr.
Signed-off-by: Kees Cook <kees@ubuntu.com> Signed-off-by: John Johansen <john.johansen@canonical.com> Signed-off-by: James Morris <jmorris@namei.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In order to make lazyinit eat approx. 10% of io bandwidth at max, we
are sleeping between zeroing each single inode table. For that purpose
we are using timer which wakes up thread when it expires. It is set
via add_timer() and this may cause troubles in the case that thread
has been woken up earlier and in next iteration we call add_timer() on
still running timer hence hitting BUG_ON in add_timer(). We could fix
that by using mod_timer() instead however we can use
schedule_timeout_interruptible() for waiting and hence simplifying
things a lot.
This commit exchange the old "waiting mechanism" with simple
schedule_timeout_interruptible(), setting the time to sleep. Hence we
do not longer need li_wait_daemon waiting queue and others, so get rid
of it.
We need to take reference to the s_li_request after we take a mutex,
because it might be freed since then, hence result in accessing old
already freed memory. Also we should protect the whole
ext4_remove_li_request() because ext4_li_info might be in the process of
being freed in ext4_lazyinit_thread().
Disk event code automatically blocks events on excl write. This is
primarily to avoid issuing polling commands while burning is in
progress. This behavior doesn't fit other types of devices with
removeable media where polling commands don't have adverse side
effects and door locking usually doesn't exist.
This patch introduces new genhd flag which controls the auto-blocking
behavior and uses it to enable auto-blocking only on optical devices.
There's a race window in xen_drop_mm_ref, where remote cpu may exit
dirty bitmap between the check on this cpu and the point where remote
cpu handles drop request. So in drop_other_mm_ref we need check
whether TLB state is still lazy before calling into leave_mm. This
bug is rarely observed in earlier kernel, but exaggerated by the
commit 831d52bc153971b70e64eccfbed2b232394f22f8
("x86, mm: avoid possible bogus tlb entries by clearing prev mm_cpumask after switching mm")
which clears bitmap after changing the TLB state. the call trace is as below:
Tested-by: Maoxiaoyun<tinnycloud@hotmail.com> Signed-off-by: Kevin Tian <kevin.tian@intel.com>
[v1: Fleshed out the git description a bit] Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When we parse the raw E820, the Xen hypervisor can set "E820_RAM"
to "E820_UNUSABLE" if the mem=X argument is used. As such we
should _not_ consider the E820_UNUSABLE as an 1-1 identity
mapping, but instead use the same case as for E820_RAM.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
git commit 24bdb0b62cc82120924762ae6bc85afc8c3f2b26 (xen: do not create
the extra e820 region at an addr lower than 4G) does not take into
account that ifdef CONFIG_X86_32 instead of e820_end_of_low_ram_pfn()
find_low_pfn_range() is called (both calls are from arch/x86/kernel/setup.c).
find_low_pfn_range() behaves correctly and does not require change in
xen_extra_mem_start initialization. Additionally, if xen_extra_mem_start
is initialized in the same way as ifdef CONFIG_X86_64 then memory hotplug
support for Xen balloon driver (under development) is broken.
Signed-off-by: Daniel Kiper <dkiper@net-space.pl> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
.. when applicable. We need to track in the p2m_mfn and
p2m_mfn_p the MFNs and pointers, respectivly, for the P2M entries
that are allocated for the identity mappings. Without this,
a PV domain with an E820 that triggers the 1-1 mapping to kick in,
won't be able to be restored as the P2M won't have the identity
mappings.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
TI816X (common name for DM816x/C6A816x/AM389x family) devices configured
to boot as PCIe Endpoint have class code = 0. This makes kernel PCI bus
code to skip allocating BARs to these devices resulting into following
type of error when trying to enable them:
"Device 0000:01:00.0 not available because of resource collisions"
The device cannot be operated because of the above issue.
This patch adds a ID specific (TI VENDOR ID and 816X DEVICE ID based)
'early' fixup quirk to replace class code with
PCI_CLASS_MULTIMEDIA_VIDEO as class.
Currently, the call to nfs4_schedule_session_recovery() will actually just
result in a test of the lease when what we really want is to force a
session reset.
Currently, if the server returns NFS4ERR_EXPIRED in reply to a READ or
WRITE, but the RENEW test determines that the lease is still active, we
fail to recover and end up looping forever in a READ/WRITE + RENEW death
spiral.
The TCP connection state code depends on the state_change() callback
being called when the SYN_SENT state is set. However the networking layer
doesn't actually call us back in that case.
None of the latest GPUs had this hooked up, this is necessary for
correct operation in a lot of cases, however we should test this on a few
GPUs in these families as we've had problems in this area before.
Reviewed-by: Alex Deucher <alexdeucher@gmail.com> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
projects / karo-tx-linux.git / log