Adam YH Lee [Thu, 13 Nov 2014 18:04:33 +0000 (10:04 -0800)]
ARM: dts: Gumstix DuoVero: Bind vdac regulator to hdmi node
The HDMI node does not have a power supply attached. As a result its
power regulator, VDAC, shuts off on boot and screen loses signal.
This attaches VDAC (vdda_hdmi_dac) to HDMI's vdda-supply.
Signed-off-by: Adam YH Lee <adam.yh.lee@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
This adds the NovaTech OrionLXm which is based on the AM335x SoC
http://www.novatechweb.com/substation-automation/orionlxm/
RAM: 512MiB
Flash: 4GB eMMC
Ethernet PHYs: 2x Micrel KSZ8041FTLI
USB ports are used internally by the expansion cards.
Internal micro SD slot is available.
Signed-off-by: George McCollister <george.mccollister@gmail.com> Reviewed-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Nishanth Menon [Fri, 7 Nov 2014 17:47:13 +0000 (11:47 -0600)]
ARM: dts: Add am57xx-beagle-x15
BeagleBoard-X15 is the next generation Open Source Hardware
BeagleBoard based on TI's AM5728 SoC featuring dual core 1.5GHz A15
processor. The platform features 2GB DDR3L (w/dual 32bit busses),
eSATA, 3 USB3.0 ports, integrated HDMI (1920x1080@60), separate LCD
port, video In port, 4GB eMMC, uSD, Analog audio in/out, dual 1G
Ethernet.
For more information, refer to:
BeagleBoard-X15 Wiki:
http://www.elinux.org/Beagleboard:BeagleBoard-X15
AM5728 is part of the Sitara product family whose additional details
will be available: http://www.ti.com/lsds/ti/arm/overview.page
Technical Reference Manual for AM5728 is public domain at:
http://www.ti.com/lit/spruhz6
Just add basic support for the moment, the following updates are needed:
i) Ethernet - depends on SoC dts fixes
ii) USB Client (USB2) - depends on GPIO extcon
ii) HDMI - additional driver fixes pending
iii) Audio - additional driver fixes pending
NOTE:
AM5728 Data Manual (SPRS915L - August 2014) section 4.1.1 states: "All
unused power supply balls must be supplied with the voltages specified
in the Section 5.2, Recommended Operating Conditions". This implies
that all unused voltage rails for AM5728 can never be switched off even
if the hardware blocks inside that voltage domain is unused. Switching
off these unused rails may result in stability issues on other domains
and increased leakage and power-on-hour impacts.
Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Nishanth Menon <nm@ti.com> Reviewed-by: Tom Rini <trini@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM: OMAP2+: igep00x0: Add pdata-quirks for the btwilink device.
Add btwilink device for IGEPv2 Rev. F and IGEP COM MODULE Rev. G.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com> Acked-by: Javier Martinez Canillas <javier@dowhile0.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
We can't suppose that the i2c2 pins are configured as I2C bus, these pins are
connected to expansion connectors.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com> Acked-by: Javier Martinez Canillas <javier@dowhile0.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM: dts: omap3-igep0020-rev-f: Support IGEPv2 Rev. F
Add support for the new hardware revision of the IGEPv2. Basically, the new
revision F replaces the old Wifi module for a Wilink8 based module.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com> Acked-by: Javier Martinez Canillas <javier@dowhile0.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM: dts: omap3-igep0020-common: Introduce igep0020 common dtsi file.
Use the omap3-igep0020-common.dtsi file and remove repeated parts leaving
the nodes that are not common between IGEPv2 hardware revisions.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com> Acked-by: Javier Martinez Canillas <javier@dowhile0.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM: dts: omap3-igep0030-rev-g: Support IGEP COM MODULE Rev. G
Add support for the new hardware revision of the IGEP COM MODULE. Basically,
the new revision G replaces the old Wifi module for a Wilink8 based module.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com> Acked-by: Javier Martinez Canillas <javier@dowhile0.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM: dts: omap3-igep0030-common: Introduce igep0030 common dtsi file.
Use the omap3-igep0030-common.dtsi file and remove repeated parts leaving
the nodes that are not common between IGEP COM MODULE hardware revisions.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com> Acked-by: Javier Martinez Canillas <javier@dowhile0.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM: dts: omap3-igep00x0: Move outside common file the on board Wifi module.
New IGEP boards revisions will use another Wifi module, so this patch moves
the DT nodes outside the common omap3-igep.dtsi file to specific DT for every
board.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com> Acked-by: Javier Martinez Canillas <javier@dowhile0.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM: dts: omap3-igep0020: Specify IGEPv2 revision in device tree.
We'll introduce new hardware revisions soon. This patch is only to
indicate which board revision supports this device tree file in order
to avoid confusions.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com> Acked-by: Javier Martinez Canillas <javier@dowhile0.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM: dts: omap3-igep0030: Specify IGEP COM revision in device tree.
We'll introduce new hardware revisions soon. This patch is only to
indicate which board revision supports this device tree file in order
to avoid confusions.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com> Acked-by: Javier Martinez Canillas <javier@dowhile0.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM: dts: omap3-igep00x0: Move NAND configuration to a common place.
At this moment all supported boards use same NAND chip, so has more sense
move the GPMC and NAND configuration to the omap3-igep.dtsi common place.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com> Acked-by: Javier Martinez Canillas <javier@dowhile0.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM: dts: omap3-igep00x0: Fix UART2 pins that aren't common.
UART2 is used to connect the processor with the bluetooth chip, these pins
are not common between IGEPv2 boards and IGEP COM MODULE boards. This patch
muxes the correct pins for every board and removes UART2 configuration from
common omap3-igep.dtsi file.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com> Acked-by: Javier Martinez Canillas <javier@dowhile0.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
Nishanth Menon [Tue, 21 Oct 2014 14:38:10 +0000 (09:38 -0500)]
ARM: dts: dra7-evm: Keep all VDD rails always-on
DRA7 Data Manual (SPRS857L - August 2014) section 4.1.1 states: "All
unused power supply balls must be supplied with the voltages specified
in the Section 5.2, Recommended Operating Conditions".
This implies that all unused voltage rails for Vayu can never be
switched off even if the hardware blocks inside that voltage domain is
unused. Switching off these unused rails may result in stability issues
on other domains and increased leakage and power-on-hour impacts.
J6eco-evm dts file already considers this, however j6evm-dts file needs
to be fixed to consider this constraint of the SoC.
Signed-off-by: Nishanth Menon <nm@ti.com> Acked-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Nishanth Menon [Tue, 21 Oct 2014 14:35:56 +0000 (09:35 -0500)]
ARM: dts: dra72-evm: Add MMC nodes
Add MMC1 and 2 nodes. MMC1 is SDcard and MMC2 is eMMC.
NOTE on MMC1 card detect: Ideally, we should be using in-built SDCD
support, but we dont have it yet. So, use the fact that control module
of DRA7 is setup such that no matter what mode one configures it, GPIO
option is always hardwired in - use GPIO mode for SDcard detection.
[peter.ujfalusi@ti.com]
The power line feeding the SD card is also used by other devices on the EVM.
Use generic name instead of mmc2_3v3 so when other devices want to use the
same regulator it will look a bit better.
Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Nishanth Menon [Tue, 21 Oct 2014 14:30:47 +0000 (09:30 -0500)]
ARM: dts: dra72-evm: Add power button node
With Commit adff5962fdd2 ("Input: introduce palmas-pwrbutton"), we can
now support tps power button as a event source - This is SW7 (PB/WAKE)
on the J6-evm.
Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
George Cherian [Tue, 21 Oct 2014 10:41:19 +0000 (13:41 +0300)]
ARM: dts: dra72-evm: Enable USB support for dra72-evm.
Add USB data and pinctrl for USB.
Signed-off-by: George Cherian <george.cherian@ti.com> Signed-off-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Mugunthan V N [Tue, 21 Oct 2014 10:01:00 +0000 (15:31 +0530)]
ARM: dts: dra7: Add CPSW and MDIO module nodes for dra7
Add CPSW and MDIO related device tree data for DRA7XX and made as status
disabled. Phy-id, pinmux for active and sleep state needs to be added in
board dts files and enable the CPSW device.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Cc: devicetree@vger.kernel.org Reviewed-by: Tony Lindgren <tony@atomide.com> Tested-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Tony Lindgren <tony@atomide.com>
Cc: devicetree@vger.kernel.org Reviewed-by: Tony Lindgren <tony@atomide.com> Tested-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Tony Lindgren <tony@atomide.com>
Suman Anna [Mon, 3 Nov 2014 23:07:34 +0000 (17:07 -0600)]
ARM: dts: DRA7: Add interrupts property to mailbox nodes
Add the interrupts property to all the 13 mailbox nodes in
DRA7xx. The interrupts property information added is inline
with the expected values with the DRA7xx crossbar driver,
and is common to both DRA74x and DRA72x SoCs.
Do note that the mailbox 1 is only capable of generating out
3 interrupts, while all the remaining mailboxes have 4
interrupts each.
Signed-off-by: Suman Anna <s-anna@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Tony Lindgren [Tue, 4 Nov 2014 00:48:16 +0000 (16:48 -0800)]
ARM: dts: Use better omap GPMC timings for LAN9220
With the GPMC warnings now enabled, I noticed the LAN9220 timings
can overflow the GPMC registers with 200MHz L3 speed. Earlier we
were just skipping the bad timings and would continue with the
bootloader timings. Now we no longer allow to continue with bad
timings as we have the timings in the .dts files.
We could start using the GPMC clock divider, but let's instead
use the u-boot timings that are known to be working and a bit
faster. These are basically the u-boot NET_GPMC_CONFIG[1-6]
defines deciphered. Except that we don't set gpmc,burst-length
as that's only partially configured and does not seem to work
if fully enabled.
[tony@atomide.com: updated to remove gpmc,burst-length] Signed-off-by: Tony Lindgren <tony@atomide.com>
Tony Lindgren [Thu, 30 Oct 2014 00:16:48 +0000 (17:16 -0700)]
ARM: dts: Add GPMC timings for omap zoom serial port
The four port serial port on the zoom debug board uses a TL16CP754C
with a single interrupt and GPMC chip select. The serial ports each
use a 8 bytes for IO registers, and are 256 bytes apart on the GPMC
line.
Let's add timings for all four ports so we can remove the GPMC
workarounds for using bootloader timings.
Not caused by this patch, but looks like u-boot only properly
initializes the fifo on the first serial port. Currently the other
ports produce garbage at least with my version of u-boot. I suspect
that TL16CP754C needs non-standard initialization added to 8250
driver to properly fix this issue.
Cc: Roger Quadros <rogerq@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Tony Lindgren [Thu, 30 Oct 2014 00:16:47 +0000 (17:16 -0700)]
ARM: dts: Fix wrong GPMC size mappings for omaps
The GPMC binding is obviously very confusing as the values
are all over the place. People seem to confuse the GPMC partition
size for the chip select, and the device IO size within the GPMC
partition easily.
The ranges entry contains the GPMC partition size. And the
reg entry contains the size of the IO registers of the
device connected to the GPMC.
Let's fix the issue according to the following table:
Device GPMC partition size Device IO size
connected in the ranges entry in the reg entry
Tony Lindgren [Thu, 30 Oct 2014 00:16:47 +0000 (17:16 -0700)]
ARM: dts: Fix bootloader version dependencies by muxing n900 smc91x pins
Apparently some versions of nolo don't mux the all the necessary GPMC
pins for the smc91x probe to work properly. Let's fix this issue
by adding mux support for GPMC to the kernel.
Note that GPMC clk needs input enabled for OnenNAND to work.
Cc: Kevin Hilman <khilman@kernel.org> Cc: Roger Quadros <rogerq@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Linus Torvalds [Sun, 26 Oct 2014 18:35:51 +0000 (11:35 -0700)]
Merge tag 'armsoc-for-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Another week, another small batch of fixes.
Most of these make zynq, socfpga and sunxi platforms work a bit
better:
- due to new requirements for regulators, DWMMC on socfpga broke past
v3.17
- SMP spinup fix for socfpga
- a few DT fixes for zynq
- another option (FIXED_REGULATOR) for sunxi is needed that used to
be selected by other options but no longer is.
- a couple of small DT fixes for at91
- ...and a couple for i.MX"
* tag 'armsoc-for-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: dts: imx28-evk: Let i2c0 run at 100kHz
ARM: i.MX6: Fix "emi" clock name typo
ARM: multi_v7_defconfig: enable CONFIG_MMC_DW_ROCKCHIP
ARM: sunxi_defconfig: enable CONFIG_REGULATOR_FIXED_VOLTAGE
ARM: dts: socfpga: Add a 3.3V fixed regulator node
ARM: dts: socfpga: Fix SD card detect
ARM: dts: socfpga: rename gpio nodes
ARM: at91/dt: sam9263: fix PLLB frequencies
power: reset: at91-reset: fix power down register
MAINTAINERS: add atmel ssc driver maintainer entry
arm: socfpga: fix fetching cpu1start_addr for SMP
ARM: zynq: DT: trivial: Fix mc node
ARM: zynq: DT: Add cadence watchdog node
ARM: zynq: DT: Add missing reference for memory-controller
ARM: zynq: DT: Add missing reference for ADC
ARM: zynq: DT: Add missing address for L2 pl310
ARM: zynq: DT: Remove 222 MHz OPP
ARM: zynq: DT: Fix GEM register area size
Olof Johansson [Sun, 26 Oct 2014 03:44:05 +0000 (20:44 -0700)]
Merge tag 'imx-fixes-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
Merge "ARM: imx: fixes for 3.18" from Shawn Guo:
The i.MX fixes for 3.18:
- Revert one patch which increases I2C bus frequency on imx28-evk
- Fix a typo on imx6q EIM clock name
* tag 'imx-fixes-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx28-evk: Let i2c0 run at 100kHz
ARM: i.MX6: Fix "emi" clock name typo
Linus Torvalds [Fri, 24 Oct 2014 19:48:47 +0000 (12:48 -0700)]
Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Pull MIPS fixes from Ralf Baechle:
"This is the first round of fixes and tying up loose ends for MIPS.
- plenty of fixes for build errors in specific obscure configurations
- remove redundant code on the Lantiq platform
- removal of a useless SEAD I2C driver that was causing a build issue
- fix an earlier TLB exeption handler fix to also work on Octeon.
- fix ISA level dependencies in FPU emulator's instruction decoding.
- don't hardcode kernel command line in Octeon software emulator.
- fix an earlier fix for the Loondson 2 clock setting"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: SEAD3: Fix I2C device registration.
MIPS: SEAD3: Nuke PIC32 I2C driver.
MIPS: ftrace: Fix a microMIPS build problem
MIPS: MSP71xx: Fix build error
MIPS: Malta: Do not build the malta-amon.c file if CMP is not enabled
MIPS: Prevent compiler warning from cop2_{save,restore}
MIPS: Kconfig: Add missing MIPS_CPS dependencies to PM and cpuidle
MIPS: idle: Remove leftover __pastwait symbol and its references
MIPS: Sibyte: Include the swarm subdir to the sb1250 LittleSur builds
MIPS: ptrace.h: Add a missing include
MIPS: ath79: Fix compilation error when CONFIG_PCI is disabled
MIPS: MSP71xx: Remove compilation error when CONFIG_MIPS_MT is present
MIPS: Octeon: Remove special case for simulator command line.
MIPS: tlbex: Properly fix HUGE TLB Refill exception handler
MIPS: loongson2_cpufreq: Fix CPU clock rate setting mismerge
pci: pci-lantiq: remove duplicate check on resource
MIPS: Lasat: Add missing CONFIG_PROC_FS dependency to PICVUE_PROC
MIPS: cp1emu: Fix ISA restrictions for cop1x_op instructions
Linus Torvalds [Fri, 24 Oct 2014 19:48:04 +0000 (12:48 -0700)]
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
- enable 48-bit VA space now that KVM has been fixed, together with a
couple of fixes for pgd allocation alignment and initial memblock
current_limit. There is still a dependency on !ARM_SMMU which needs
to be updated as it uses the page table manipulation macros of the
host kernel
- eBPF fixes following changes/conflicts during the merging window
- Compat types affecting compat_elf_prpsinfo
- Compilation error on UP builds
- ASLR fix when /proc/sys/kernel/randomize_va_space == 0
- DT definitions for CLCD support on ARMv8 model platform
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: Fix memblock current_limit with 64K pages and 48-bit VA
arm64: ASLR: Don't randomise text when randomise_va_space == 0
arm64: vexpress: Add CLCD support to the ARMv8 model platform
arm64: Fix compilation error on UP builds
Documentation/arm64/memory.txt: fix typo
net: bpf: arm64: minor fix of type in jited
arm64: bpf: add 'load 64-bit immediate' instruction
arm64: bpf: add 'shift by register' instructions
net: bpf: arm64: address randomize and write protect JIT code
arm64: mm: Correct fixmap pagetable types
arm64: compat: fix compat types affecting struct compat_elf_prpsinfo
arm64: Align less than PAGE_SIZE pgds naturally
arm64: Allow 48-bits VA space without ARM_SMMU
1) Fix boots with gcc-4.9 compiled sparc64 kernels.
2) Add missing __get_user_pages_fast() on sparc64 to fix hangs on
futexes used in transparent hugepage areas.
It's really idiotic to have a weak symbolled fallback that just
returns zero, and causes this kind of bug. There should be no
backup implementation and the link should fail if the architecture
fails to provide __get_user_pages_fast() and supports transparent
hugepages.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc64: Implement __get_user_pages_fast().
sparc64: Fix register corruption in top-most kernel stack frame during boot.
Linus Torvalds [Fri, 24 Oct 2014 19:42:55 +0000 (12:42 -0700)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm fixes from Paolo Bonzini:
"This is a pretty large update. I think it is roughly as big as what I
usually had for the _whole_ rc period.
There are a few bad bugs where the guest can OOPS or crash the host.
We have also started looking at attack models for nested
virtualization; bugs that usually result in the guest ring 0 crashing
itself become more worrisome if you have nested virtualization,
because the nested guest might bring down the non-nested guest as
well. For current uses of nested virtualization these do not really
have a security impact, but you never know and bugs are bugs
nevertheless.
A lot of these bugs are in 3.17 too, resulting in a large number of
stable@ Ccs. I checked that all the patches apply there with no
conflicts"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
kvm: vfio: fix unregister kvm_device_ops of vfio
KVM: x86: Wrong assertion on paging_tmpl.h
kvm: fix excessive pages un-pinning in kvm_iommu_map error path.
KVM: x86: PREFETCH and HINT_NOP should have SrcMem flag
KVM: x86: Emulator does not decode clflush well
KVM: emulate: avoid accessing NULL ctxt->memopp
KVM: x86: Decoding guest instructions which cross page boundary may fail
kvm: x86: don't kill guest on unknown exit reason
kvm: vmx: handle invvpid vm exit gracefully
KVM: x86: Handle errors when RIP is set during far jumps
KVM: x86: Emulator fixes for eip canonical checks on near branches
KVM: x86: Fix wrong masking on relative jump/call
KVM: x86: Improve thread safety in pit
KVM: x86: Prevent host from panicking on shared MSR writes.
KVM: x86: Check non-canonical addresses upon WRMSR
Linus Torvalds [Fri, 24 Oct 2014 19:41:50 +0000 (12:41 -0700)]
Merge tag 'stable/for-linus-3.18-b-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen bug fixes from David Vrabel:
- Fix regression in xen_clocksource_read() which caused all Xen guests
to crash early in boot.
- Several fixes for super rare race conditions in the p2m.
- Assorted other minor fixes.
* tag 'stable/for-linus-3.18-b-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/pci: Allocate memory for physdev_pci_device_add's optarr
x86/xen: panic on bad Xen-provided memory map
x86/xen: Fix incorrect per_cpu accessor in xen_clocksource_read()
x86/xen: avoid race in p2m handling
x86/xen: delay construction of mfn_list_list
x86/xen: avoid writing to freed memory after race in p2m handling
xen/balloon: Don't continue ballooning when BP_ECANCELED is encountered
Linus Torvalds [Fri, 24 Oct 2014 19:35:48 +0000 (12:35 -0700)]
Merge tag 'sound-3.18-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Here are a chunk of small fixes since rc1: two PCM core fixes, one is
a long-standing annoyance about lockdep and another is an ARM64 mmap
fix.
The rest are a HD-audio HDMI hotplug notification fix, a fix for
missing NULL termination in Realtek codec quirks and a few new
device/codec-specific quirks as usual"
* tag 'sound-3.18-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Add missing terminating entry to SND_HDA_PIN_QUIRK macro
ALSA: pcm: Fix false lockdep warnings
ALSA: hda - Fix inverted LED gpio setup for Lenovo Ideapad
ALSA: hda - hdmi: Fix missing ELD change event on plug/unplug
ALSA: usb-audio: Add support for Steinberg UR22 USB interface
ALSA: ALC283 codec - Avoid pop noise on headphones during suspend/resume
ALSA: pcm: use the same dma mmap codepath both for arm and arm64
Linus Torvalds [Fri, 24 Oct 2014 19:33:32 +0000 (12:33 -0700)]
Merge tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random
Pull /dev/random updates from Ted Ts'o:
"This adds a memzero_explicit() call which is guaranteed not to be
optimized away by GCC. This is important when we are wiping
cryptographically sensitive material"
* tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random:
crypto: memzero_explicit - make sure to clear out sensitive data
random: add and use memzero_explicit() for clearing data
Linus Torvalds [Fri, 24 Oct 2014 18:29:31 +0000 (11:29 -0700)]
Merge tag 'pm+acpi-3.18-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
"This is material that didn't make it to my 3.18-rc1 pull request for
various reasons, mostly related to timing and travel (LinuxCon EU /
LPC) plus a couple of fixes for recent bugs.
The only really new thing here is the PM QoS class for memory
bandwidth, but it is simple enough and users of it will be added in
the next cycle. One major change in behavior is that platform devices
enumerated by ACPI will use 32-bit DMA mask by default. Also included
is an ACPICA update to a new upstream release, but that's mostly
cleanups, changes in tools and similar. The rest is fixes and
cleanups mostly.
Specifics:
- Fix for a recent PCI power management change that overlooked the
fact that some IRQ chips might not be able to configure PCIe PME
for system wakeup from Lucas Stach.
- Fix for a bug introduced in 3.17 where acpi_device_wakeup() is
called with a wrong ordering of arguments from Zhang Rui.
- A bunch of intel_pstate driver fixes (all -stable candidates) from
Dirk Brandewie, Gabriele Mazzotta and Pali Rohár.
- Fixes for a rather long-standing problem with the OOM killer and
the freezer that frozen processes killed by the OOM do not actually
release any memory until they are thawed, so OOM-killing them is
rather pointless, with a couple of cleanups on top (Michal Hocko,
Cong Wang, Rafael J Wysocki).
- ACPICA update to upstream release 20140926, inlcuding mostly
cleanups reducing differences between the upstream ACPICA and the
kernel code, tools changes (acpidump, acpiexec) and support for the
_DDN object (Bob Moore, Lv Zheng).
- New PM QoS class for memory bandwidth from Tomeu Vizoso.
- Default 32-bit DMA mask for platform devices enumerated by ACPI
(this change is mostly needed for some drivers development in
progress targeted at 3.19) from Heikki Krogerus.
- ACPI EC driver cleanups, mostly related to debugging, from Lv
Zheng.
- cpufreq-dt driver updates from Thomas Petazzoni.
- powernv cpuidle driver update from Preeti U Murthy"
* tag 'pm+acpi-3.18-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (34 commits)
intel_pstate: Correct BYT VID values.
intel_pstate: Fix BYT frequency reporting
intel_pstate: Don't lose sysfs settings during cpu offline
cpufreq: intel_pstate: Reflect current no_turbo state correctly
cpufreq: expose scaling_cur_freq sysfs file for set_policy() drivers
cpufreq: intel_pstate: Fix setting max_perf_pct in performance policy
PCI / PM: handle failure to enable wakeup on PCIe PME
ACPI: invoke acpi_device_wakeup() with correct parameters
PM / freezer: Clean up code after recent fixes
PM: convert do_each_thread to for_each_process_thread
OOM, PM: OOM killed task shouldn't escape PM suspend
freezer: remove obsolete comments in __thaw_task()
freezer: Do not freeze tasks killed by OOM killer
ACPI / platform: provide default DMA mask
cpuidle: powernv: Populate cpuidle state details by querying the device-tree
cpufreq: cpufreq-dt: adjust message related to regulators
cpufreq: cpufreq-dt: extend with platform_data
cpufreq: allow driver-specific data
ACPI / EC: Cleanup coding style.
ACPI / EC: Refine event/query debugging messages.
...
Linus Torvalds [Fri, 24 Oct 2014 18:21:43 +0000 (11:21 -0700)]
Merge branch 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux
Pull thermal management updates from Zhang Rui:
"Sorry that I missed the merge window as there is a bug found in the
last minute, and I have to fix it and wait for the code to be tested
in linux-next tree for a few days. Now the buggy patch has been
dropped entirely from my next branch. Thus I hope those changes can
still be merged in 3.18-rc2 as most of them are platform thermal
driver changes.
Specifics:
- introduce ACPI INT340X thermal drivers.
Newer laptops and tablets may have thermal sensors and other
devices with thermal control capabilities that are exposed for the
OS to use via the ACPI INT340x device objects. Several drivers are
introduced to expose the temperature information and cooling
ability from these objects to user-space via the normal thermal
framework.
From: Lu Aaron, Lan Tianyu, Jacob Pan and Zhang Rui.
- introduce a new thermal governor, which just uses a hysteresis to
switch abruptly on/off a cooling device. This governor can be used
to control certain fan devices that can not be throttled but just
switched on or off. From: Peter Feuerer.
- introduce support for some new thermal interrupt functions on
i.MX6SX, in IMX thermal driver. From: Anson, Huang.
- introduce tracing support on thermal framework. From: Punit
Agrawal.
- small fixes in OF thermal and thermal step_wise governor"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux: (25 commits)
Thermal: int340x thermal: select ACPI fan driver
Thermal: int3400_thermal: use acpi_thermal_rel parsing APIs
Thermal: int340x_thermal: expose acpi thermal relationship tables
Thermal: introduce int3403 thermal driver
Thermal: introduce INT3402 thermal driver
Thermal: move the KELVIN_TO_MILLICELSIUS macro to thermal.h
ACPI / Fan: support INT3404 thermal device
ACPI / Fan: add ACPI 4.0 style fan support
ACPI / fan: convert to platform driver
ACPI / fan: use acpi_device_xxx_power instead of acpi_bus equivelant
ACPI / fan: remove no need check for device pointer
ACPI / fan: remove unused macro
Thermal: int3400 thermal: register to thermal framework
Thermal: int3400 thermal: add capability to detect supporting UUIDs
Thermal: introduce int3400 thermal driver
ACPI: add ACPI_TYPE_LOCAL_REFERENCE support to acpi_extract_package()
ACPI: make acpi_create_platform_device() an external API
thermal: step_wise: fix: Prevent from binary overflow when trend is dropping
ACPI: introduce ACPI int340x thermal scan handler
thermal: Added Bang-bang thermal governor
...
Catalin Marinas [Fri, 24 Oct 2014 17:16:47 +0000 (18:16 +0100)]
arm64: Fix memblock current_limit with 64K pages and 48-bit VA
With 48-bit VA space, the 64K page configuration uses 3 levels instead
of 2 and PUD_SIZE != PMD_SIZE. Since with 64K pages we only cover
PMD_SIZE with the initial swapper_pg_dir populated in head.S, the
memblock current_limit needs to be set accordingly in map_mem() to avoid
allocating unmapped memory. The memblock current_limit is progressively
increased as more blocks are mapped.
David S. Miller [Fri, 24 Oct 2014 16:59:02 +0000 (09:59 -0700)]
sparc64: Implement __get_user_pages_fast().
It is not sufficient to only implement get_user_pages_fast(), you
must also implement the atomic version __get_user_pages_fast()
otherwise you end up using the weak symbol fallback implementation
which simply returns zero.
This is dangerous, because it causes the futex code to loop forever
if transparent hugepages are supported (see get_futex_key()).
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 23 Oct 2014 19:58:13 +0000 (12:58 -0700)]
sparc64: Fix register corruption in top-most kernel stack frame during boot.
Meelis Roos reported that kernels built with gcc-4.9 do not boot, we
eventually narrowed this down to only impacting machines using
UltraSPARC-III and derivitive cpus.
The crash happens right when the first user process is spawned:
[ 54.451346] Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000004
[ 54.451346]
[ 54.571516] CPU: 1 PID: 1 Comm: init Not tainted 3.16.0-rc2-00211-gd7933ab #96
[ 54.666431] Call Trace:
[ 54.698453] [0000000000762f8c] panic+0xb0/0x224
[ 54.759071] [000000000045cf68] do_exit+0x948/0x960
[ 54.823123] [000000000042cbc0] fault_in_user_windows+0xe0/0x100
[ 54.902036] [0000000000404ad0] __handle_user_windows+0x0/0x10
[ 54.978662] Press Stop-A (L1-A) to return to the boot prom
[ 55.050713] ---[ end Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000004
Further investigation showed that compiling only per_cpu_patch() with
an older compiler fixes the boot.
Detailed analysis showed that the function is not being miscompiled by
gcc-4.9, but it is using a different register allocation ordering.
With the gcc-4.9 compiled function, something during the code patching
causes some of the %i* input registers to get corrupted. Perhaps
we have a TLB miss path into the firmware that is deep enough to
cause a register window spill and subsequent restore when we get
back from the TLB miss trap.
Let's plug this up by doing two things:
1) Stop using the firmware stack for client interface calls into
the firmware. Just use the kernel's stack.
2) As soon as we can, call into a new function "start_early_boot()"
to put a one-register-window buffer between the firmware's
deepest stack frame and the top-most initial kernel one.
Reported-by: Meelis Roos <mroos@linux.ee> Tested-by: Meelis Roos <mroos@linux.ee> Signed-off-by: David S. Miller <davem@davemloft.net>
Arun Chandran [Fri, 10 Oct 2014 11:31:24 +0000 (12:31 +0100)]
arm64: ASLR: Don't randomise text when randomise_va_space == 0
When user asks to turn off ASLR by writing "0" to
/proc/sys/kernel/randomize_va_space there should not be
any randomization to mmap base, stack, VDSO, libs, text and heap
Currently arm64 violates this behavior by randomising text.
Fix this by defining a constant ELF_ET_DYN_BASE. The randomisation of
mm->mmap_base is done by setup_new_exec -> arch_pick_mmap_layout ->
mmap_base -> mmap_rnd.
Wanpeng Li [Thu, 9 Oct 2014 10:30:08 +0000 (18:30 +0800)]
kvm: vfio: fix unregister kvm_device_ops of vfio
After commit 80ce163 (KVM: VFIO: register kvm_device_ops dynamically),
kvm_device_ops of vfio can be registered dynamically. Commit 3c3c29fd
(kvm-vfio: do not use module_init) move the dynamic register invoked by
kvm_init in order to fix broke unloading of the kvm module. However,
kvm_device_ops of vfio is unregistered after rmmod kvm-intel module
which lead to device type collision detection warning after kvm-intel
module reinsmod.
without rmmod/insmod kvm.ko
This patch fixes the bug by unregistering kvm_device_ops of vfio when the
kvm-intel module is removed.
Reported-by: Liu Rongrong <rongrongx.liu@intel.com> Fixes: 3c3c29fd0d7cddc32862c350d0700ce69953e3bd Signed-off-by: Wanpeng Li <wanpeng.li@linux.intel.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Nadav Amit [Tue, 30 Sep 2014 17:49:18 +0000 (20:49 +0300)]
KVM: x86: Wrong assertion on paging_tmpl.h
Even after the recent fix, the assertion on paging_tmpl.h is triggered.
Apparently, the assertion wants to check that the PAE is always set on
long-mode, but does it in incorrect way. Note that the assertion is not
enabled unless the code is debugged by defining MMU_DEBUG.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
kvm: fix excessive pages un-pinning in kvm_iommu_map error path.
The third parameter of kvm_unpin_pages() when called from
kvm_iommu_map_pages() is wrong, it should be the number of pages to un-pin
and not the page size.
This error was facilitated with an inconsistent API: kvm_pin_pages() takes
a size, but kvn_unpin_pages() takes a number of pages, so fix the problem
by matching the two.
This was introduced by commit 350b8bd ("kvm: iommu: fix the third parameter
of kvm_iommu_put_pages (CVE-2014-3601)"), which fixes the lack of
un-pinning for pages intended to be un-pinned (i.e. memory leak) but
unfortunately potentially aggravated the number of pages we un-pin that
should have stayed pinned. As far as I understand though, the same
practical mitigations apply.
This issue was found during review of Red Hat 6.6 patches to prepare
Ksplice rebootless updates.
Thanks to Vegard for his time on a late Friday evening to help me in
understanding this code.
Nadav Amit [Mon, 13 Oct 2014 10:04:14 +0000 (13:04 +0300)]
KVM: x86: PREFETCH and HINT_NOP should have SrcMem flag
The decode phase of the x86 emulator assumes that every instruction with the
ModRM flag, and which can be used with RIP-relative addressing, has either
SrcMem or DstMem. This is not the case for several instructions - prefetch,
hint-nop and clflush.
Adding SrcMem|NoAccess for prefetch and hint-nop and SrcMem for clflush.
This fixes CVE-2014-8480.
Fixes: 41061cdb98a0bec464278b4db8e894a3121671f5 Cc: stable@vger.kernel.org Signed-off-by: Nadav Amit <namit@cs.technion.ac.il> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Nadav Amit [Mon, 13 Oct 2014 10:04:13 +0000 (13:04 +0300)]
KVM: x86: Emulator does not decode clflush well
Currently, all group15 instructions are decoded as clflush (e.g., mfence,
xsave). In addition, the clflush instruction requires no prefix (66/f2/f3)
would exist. If prefix exists it may encode a different instruction (e.g.,
clflushopt).
Creating a group for clflush, and different group for each prefix.
This has been the case forever, but the next patch needs the cflush group
in order to fix a bug introduced in 3.17.
Fixes: 41061cdb98a0bec464278b4db8e894a3121671f5 Cc: stable@vger.kernel.org Signed-off-by: Nadav Amit <namit@cs.technion.ac.il> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Paolo Bonzini [Thu, 23 Oct 2014 12:54:14 +0000 (14:54 +0200)]
KVM: emulate: avoid accessing NULL ctxt->memopp
A failure to decode the instruction can cause a NULL pointer access.
This is fixed simply by moving the "done" label as close as possible
to the return.
This fixes CVE-2014-8481.
Reported-by: Andy Lutomirski <luto@amacapital.net> Cc: stable@vger.kernel.org Fixes: 41061cdb98a0bec464278b4db8e894a3121671f5 Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Ralf Baechle [Fri, 24 Oct 2014 11:27:37 +0000 (13:27 +0200)]
MIPS: SEAD3: Nuke PIC32 I2C driver.
A platform driver for which nothing ever registers the corresponding
platform device.
Also it was driving the same hardware as sead3-i2c-drv.c so redundant
anyway and couldn't co-exist with that driver because each of them was
using a private spinlock to protect access to the same hardware
resources.
This also fixes a randconfig problem:
arch/mips/mti-sead3/sead3-pic32-i2c-drv.c: In function 'i2c_platform_probe':
arch/mips/mti-sead3/sead3-pic32-i2c-drv.c:345:2: error: implicit declaration of
function 'i2c_add_numbered_adapter' [-Werror=implicit-function-declaration]
ret = i2c_add_numbered_adapter(&priv->adap);
^
arch/mips/mti-sead3/sead3-pic32-i2c-drv.c: In function
'i2c_platform_remove':
arch/mips/mti-sead3/sead3-pic32-i2c-drv.c:361:2: error: implicit declaration
of function 'i2c_del_adapter' [-Werror=implicit-function-declaration]
i2c_del_adapter(&priv->adap);
Nadav Amit [Thu, 2 Oct 2014 22:10:04 +0000 (01:10 +0300)]
KVM: x86: Decoding guest instructions which cross page boundary may fail
Once an instruction crosses a page boundary, the size read from the second page
disregards the common case that part of the operand resides on the first page.
As a result, fetch of long insturctions may fail, and thereby cause the
decoding to fail as well.
Cc: stable@vger.kernel.org Fixes: 5cfc7e0f5e5e1adf998df94f8e36edaf5d30d38e Signed-off-by: Nadav Amit <namit@cs.technion.ac.il> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
KVM_EXIT_UNKNOWN is a kvm bug, we don't really know whether it was
triggered by a priveledged application. Let's not kill the guest: WARN
and inject #UD instead.
Cc: stable@vger.kernel.org Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Petr Matousek [Tue, 23 Sep 2014 18:22:30 +0000 (20:22 +0200)]
kvm: vmx: handle invvpid vm exit gracefully
On systems with invvpid instruction support (corresponding bit in
IA32_VMX_EPT_VPID_CAP MSR is set) guest invocation of invvpid
causes vm exit, which is currently not handled and results in
propagation of unknown exit to userspace.
Fix this by installing an invvpid vm exit handler.
This is CVE-2014-3646.
Cc: stable@vger.kernel.org Signed-off-by: Petr Matousek <pmatouse@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Nadav Amit [Thu, 18 Sep 2014 19:39:39 +0000 (22:39 +0300)]
KVM: x86: Handle errors when RIP is set during far jumps
Far jmp/call/ret may fault while loading a new RIP. Currently KVM does not
handle this case, and may result in failed vm-entry once the assignment is
done. The tricky part of doing so is that loading the new CS affects the
VMCS/VMCB state, so if we fail during loading the new RIP, we are left in
unconsistent state. Therefore, this patch saves on 64-bit the old CS
descriptor and restores it if loading RIP failed.
This fixes CVE-2014-3647.
Cc: stable@vger.kernel.org Signed-off-by: Nadav Amit <namit@cs.technion.ac.il> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Nadav Amit [Thu, 18 Sep 2014 19:39:38 +0000 (22:39 +0300)]
KVM: x86: Emulator fixes for eip canonical checks on near branches
Before changing rip (during jmp, call, ret, etc.) the target should be asserted
to be canonical one, as real CPUs do. During sysret, both target rsp and rip
should be canonical. If any of these values is noncanonical, a #GP exception
should occur. The exception to this rule are syscall and sysenter instructions
in which the assigned rip is checked during the assignment to the relevant
MSRs.
This patch fixes the emulator to behave as real CPUs do for near branches.
Far branches are handled by the next patch.
This fixes CVE-2014-3647.
Cc: stable@vger.kernel.org Signed-off-by: Nadav Amit <namit@cs.technion.ac.il> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Andy Honig [Wed, 27 Aug 2014 21:42:54 +0000 (14:42 -0700)]
KVM: x86: Improve thread safety in pit
There's a race condition in the PIT emulation code in KVM. In
__kvm_migrate_pit_timer the pit_timer object is accessed without
synchronization. If the race condition occurs at the wrong time this
can crash the host kernel.
This fixes CVE-2014-3611.
Cc: stable@vger.kernel.org Signed-off-by: Andrew Honig <ahonig@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Andy Honig [Wed, 27 Aug 2014 18:16:44 +0000 (11:16 -0700)]
KVM: x86: Prevent host from panicking on shared MSR writes.
The previous patch blocked invalid writes directly when the MSR
is written. As a precaution, prevent future similar mistakes by
gracefulling handle GPs caused by writes to shared MSRs.
Cc: stable@vger.kernel.org Signed-off-by: Andrew Honig <ahonig@google.com>
[Remove parts obsoleted by Nadav's patch. - Paolo] Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Nadav Amit [Tue, 16 Sep 2014 00:24:05 +0000 (03:24 +0300)]
KVM: x86: Check non-canonical addresses upon WRMSR
Upon WRMSR, the CPU should inject #GP if a non-canonical value (address) is
written to certain MSRs. The behavior is "almost" identical for AMD and Intel
(ignoring MSRs that are not implemented in either architecture since they would
anyhow #GP). However, IA32_SYSENTER_ESP and IA32_SYSENTER_EIP cause #GP if
non-canonical address is written on Intel but not on AMD (which ignores the top
32-bits).
Accordingly, this patch injects a #GP on the MSRs which behave identically on
Intel and AMD. To eliminate the differences between the architecutres, the
value which is written to IA32_SYSENTER_ESP and IA32_SYSENTER_EIP is turned to
canonical value before writing instead of injecting a #GP.
Some references from Intel and AMD manuals:
According to Intel SDM description of WRMSR instruction #GP is expected on
WRMSR "If the source register contains a non-canonical address and ECX
specifies one of the following MSRs: IA32_DS_AREA, IA32_FS_BASE, IA32_GS_BASE,
IA32_KERNEL_GS_BASE, IA32_LSTAR, IA32_SYSENTER_EIP, IA32_SYSENTER_ESP."
According to AMD manual instruction manual:
LSTAR/CSTAR (SYSCALL): "The WRMSR instruction loads the target RIP into the
LSTAR and CSTAR registers. If an RIP written by WRMSR is not in canonical
form, a general-protection exception (#GP) occurs."
IA32_GS_BASE and IA32_FS_BASE (WRFSBASE/WRGSBASE): "The address written to the
base field must be in canonical form or a #GP fault will occur."
IA32_KERNEL_GS_BASE (SWAPGS): "The address stored in the KernelGSbase MSR must
be in canonical form."
This patch fixes CVE-2014-3610.
Cc: stable@vger.kernel.org Signed-off-by: Nadav Amit <namit@cs.technion.ac.il> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Olof Johansson [Fri, 24 Oct 2014 04:05:45 +0000 (21:05 -0700)]
Merge tag 'socfpga_fixes_for_3.18' of git://git.rocketboards.org/linux-socfpga-next into fixes
Merge "SOCFPGA fixes for 3.18" from Dinh Nguyen:
These patches fixes an SMP and SDMMC driver hang during boot up on the
SOCFPGA platform.
Patch "arm: socfpga: fix fetching cpu1start_addr for SMP" fixes the SMP
trampoline code in order for CPU1 to correctly fetch it's cpu1start_addr.
Patch "ARM: dts: socfpga: rename gpio nodes" renames that GPIO node in order
to allow a standard way of specifying status="okay" in the board DTS file.
Patch "ARM: dts: socfpga: Fix SD card detect" fixes a SDMMC driver hang
during boot. The reason for the hang was the deferred probe of the SDMMC
driver was waiting for the GPIO resource that would never come.
Patch "ARM: dts: socfpga: Add a 3.3V fixed regulator node" adds a fixed
regulator node for the SDMMC driver to use.
* tag 'socfpga_fixes_for_3.18' of git://git.rocketboards.org/linux-socfpga-next:
ARM: dts: socfpga: Add a 3.3V fixed regulator node
ARM: dts: socfpga: Fix SD card detect
ARM: dts: socfpga: rename gpio nodes
arm: socfpga: fix fetching cpu1start_addr for SMP
Olof Johansson [Fri, 24 Oct 2014 04:02:49 +0000 (21:02 -0700)]
Merge tag 'at91-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91 into fixes
Merge "at91: fixes for v3.18 #1" from Nicholas Ferre:
First AT91 fixes for 3.18:
- one more MAINTAINERS entry for the SSC driver
- a fix for the newly introduced power/reset driver
- a fix on at91sam9263 USB due to PLLB misconfiguration
* tag 'at91-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
ARM: at91/dt: sam9263: fix PLLB frequencies
power: reset: at91-reset: fix power down register
MAINTAINERS: add atmel ssc driver maintainer entry
Al Viro [Thu, 23 Oct 2014 17:26:21 +0000 (13:26 -0400)]
fix inode leaks on d_splice_alias() failure exits
d_splice_alias() callers expect it to either stash the inode reference
into a new alias, or drop the inode reference. That makes it possible
to just return d_splice_alias() result from ->lookup() instance, without
any extra housekeeping required.
Unfortunately, that should include the failure exits. If d_splice_alias()
returns an error, it leaves the dentry it has been given negative and
thus it *must* drop the inode reference. Easily fixed, but it goes way
back and will need backporting.
Cc: stable@vger.kernel.org Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Markos Chandras [Mon, 20 Oct 2014 08:39:31 +0000 (09:39 +0100)]
MIPS: ftrace: Fix a microMIPS build problem
Code before the .fixup section needs to have the .insn directive.
This has no side effects on MIPS32/64 but it affects the way microMIPS
loads the address for the return label.
Fixes the following build problem:
mips-linux-gnu-ld: arch/mips/built-in.o: .fixup+0x4a0: Unsupported jump between
ISA modes; consider recompiling with interlinking enabled.
mips-linux-gnu-ld: final link failed: Bad value
Makefile:819: recipe for target 'vmlinux' failed
The fix is similar to 1658f914ff91c3bf ("MIPS: microMIPS:
Disable LL/SC and fix linker bug.")
Miklos Szeredi [Thu, 23 Oct 2014 22:14:39 +0000 (00:14 +0200)]
fs: limit filesystem stacking depth
Add a simple read-only counter to super_block that indicates how deep this
is in the stack of filesystems. Previously ecryptfs was the only stackable
filesystem and it explicitly disallowed multiple layers of itself.
Overlayfs, however, can be stacked recursively and also may be stacked
on top of ecryptfs or vice versa.
To limit the kernel stack usage we must limit the depth of the
filesystem stack. Initially the limit is set to 2.
Erez Zadok [Thu, 23 Oct 2014 22:14:38 +0000 (00:14 +0200)]
overlayfs: implement show_options
This is useful because of the stacking nature of overlayfs. Users like to
find out (via /proc/mounts) which lower/upper directory were used at mount
time.
AV: even failing ovl_parse_opt() could've done some kstrdup()
AV: failure of ovl_alloc_entry() should end up with ENOMEM, not EINVAL
Andy Whitcroft [Thu, 23 Oct 2014 22:14:38 +0000 (00:14 +0200)]
overlayfs: add statfs support
Add support for statfs to the overlayfs filesystem. As the upper layer
is the target of all write operations assume that the space in that
filesystem is the space in the overlayfs. There will be some inaccuracy as
overwriting a file will copy it up and consume space we were not expecting,
but it is better than nothing.
Use the upper layer dentry and mount from the overlayfs root inode,
passing the statfs call to that filesystem.
Signed-off-by: Andy Whitcroft <apw@canonical.com> Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Miklos Szeredi [Thu, 23 Oct 2014 22:14:38 +0000 (00:14 +0200)]
overlay filesystem
Overlayfs allows one, usually read-write, directory tree to be
overlaid onto another, read-only directory tree. All modifications
go to the upper, writable layer.
This type of mechanism is most often used for live CDs but there's a
wide variety of other uses.
The implementation differs from other "union filesystem"
implementations in that after a file is opened all operations go
directly to the underlying, lower or upper, filesystems. This
simplifies the implementation and allows native performance in these
cases.
The dentry tree is duplicated from the underlying filesystems, this
enables fast cached lookups without adding special support into the
VFS. This uses slightly more memory than union mounts, but dentries
are relatively small.
Currently inodes are duplicated as well, but it is a possible
optimization to share inodes for non-directories.
Opening non directories results in the open forwarded to the
underlying filesystem. This makes the behavior very similar to union
mounts (with the same limitations vs. fchmod/fchown on O_RDONLY file
descriptors).
Usage:
mount -t overlayfs overlayfs -olowerdir=/lower,upperdir=/upper/upper,workdir=/upper/work /overlay
The following cotributions have been folded into this patch:
Neil Brown <neilb@suse.de>:
- minimal remount support
- use correct seek function for directories
- initialise is_real before use
- rename ovl_fill_cache to ovl_dir_read
Felix Fietkau <nbd@openwrt.org>:
- fix a deadlock in ovl_dir_read_merged
- fix a deadlock in ovl_remove_whiteouts
Erez Zadok <ezk@fsl.cs.sunysb.edu>
- fix cleanup after WARN_ON
Sedat Dilek <sedat.dilek@googlemail.com>
- fix up permission to confirm to new API
Robin Dong <hao.bigrat@gmail.com>
- fix possible leak in ovl_new_inode
- create new inode in ovl_link
Andy Whitcroft <apw@canonical.com>
- switch to __inode_permission()
- copy up i_uid/i_gid from the underlying inode
AV:
- ovl_copy_up_locked() - dput(ERR_PTR(...)) on two failure exits
- ovl_clear_empty() - one failure exit forgetting to do unlock_rename(),
lack of check for udir being the parent of upper, dropping and regaining
the lock on udir (which would require _another_ check for parent being
right).
- bogus d_drop() in copyup and rename [fix from your mail]
- copyup/remove and copyup/rename races [fix from your mail]
- ovl_dir_fsync() leaving ERR_PTR() in ->realfile
- ovl_entry_free() is pointless - it's just a kfree_rcu()
- fold ovl_do_lookup() into ovl_lookup()
- manually assigning ->d_op is wrong. Just use ->s_d_op.
[patches picked from Miklos]:
* copyup/remove and copyup/rename races
* bogus d_drop() in copyup and rename
Also thanks to the following people for testing and reporting bugs:
Jordi Pujol <jordipujolp@gmail.com>
Andy Whitcroft <apw@canonical.com>
Michal Suchanek <hramrach@centrum.cz>
Felix Fietkau <nbd@openwrt.org>
Erez Zadok <ezk@fsl.cs.sunysb.edu>
Randy Dunlap <rdunlap@xenotime.net>
Miklos Szeredi [Thu, 23 Oct 2014 22:14:37 +0000 (00:14 +0200)]
shmem: support RENAME_WHITEOUT
Allocate a dentry, initialize it with a whiteout and hash it in the place
of the old dentry. Later the old dentry will be moved away and the
whiteout will remain.
Miklos Szeredi [Thu, 23 Oct 2014 22:14:37 +0000 (00:14 +0200)]
ext4: support RENAME_WHITEOUT
Add whiteout support to ext4_rename(). A whiteout inode (chrdev/0,0) is
created before the rename takes place. The whiteout inode is added to the
old entry instead of deleting it.
projects / karo-tx-linux.git / log