Vlad Yasevich [Mon, 16 Nov 2015 20:43:45 +0000 (15:43 -0500)]
vlan: Do not put vlan headers back on bridge and macvlan ports
When a vlan is configured with REORDER_HEADER set to 0, the vlan
header is put back into the packet and makes it appear that
the vlan header is still there even after it's been processed.
This posses a problem for bridge and macvlan ports. The packets
passed to those device may be forwarded and at the time of the
forward, vlan headers end up being unexpectedly present.
With the patch, we make sure that we do not put the vlan header
back (when REORDER_HEADER is 0) if a bridge or macvlan has
been configured on top of the vlan device.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vlad Yasevich [Mon, 16 Nov 2015 20:43:44 +0000 (15:43 -0500)]
vlan: Fix untag operations of stacked vlans with REORDER_HEADER off
When we have multiple stacked vlan devices all of which have
turned off REORDER_HEADER flag, the untag operation does not
locate the ethernet addresses correctly for nested vlans.
The reason is that in case of REORDER_HEADER flag being off,
the outer vlan headers are put back and the mac_len is adjusted
to account for the presense of the header. Then, the subsequent
untag operation, for the next level vlan, always use VLAN_ETH_HLEN
to locate the begining of the ethernet header and that ends up
being a multiple of 4 bytes short of the actuall beginning
of the mac header (the multiple depending on the how many vlan
encapsulations ethere are).
As a reslult, if there are multiple levles of vlan devices
with REODER_HEADER being off, the recevied packets end up
being dropped.
To solve this, we use skb->mac_len as the offset. The value
is always set on receive path and starts out as a ETH_HLEN.
The value is also updated when the vlan header manupations occur
so we know it will be correct.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Timo Teräs [Mon, 16 Nov 2015 12:36:32 +0000 (14:36 +0200)]
via-velocity: unconditionally drop frames with bad l2 length
By default the driver allowed incorrect frames to be received. What is
worse the code does not handle very short frames correctly. The FCS
length is unconditionally subtracted, and the underflow can cause
skb_put to be called with large number after implicit cast to unsigned.
And indeed, an skb_over_panic() was observed with via-velocity.
This removes the module parameter as it does not work in it's
current state, and should be implemented via NETIF_F_RXALL if needed.
Suggested-by: Francois Romieu <romieu@fr.zoreil.com> Signed-off-by: Timo Teräs <timo.teras@iki.fi> Signed-off-by: David S. Miller <davem@davemloft.net>
Ondrej Zary [Sun, 15 Nov 2015 21:36:11 +0000 (22:36 +0100)]
dl2k: Add support for IP1000A-based cards
Add support for IP1000A chips to dl2k driver.
IP1000A chip looks like a TC9020 with integrated PHY.
This allows IP1000A chips to work reliably because the ipg driver is
buggy - it loses packets under load and then completely stops
transmitting data.
Tested with Asus NX1101 v2.0 at 10, 100 and 1000Mbps:
vendor=0x13f0 device=0x1023 (rev 0x41)
subsystem vendor=0x1043 device=0x8180
MAC address registers access needed to be changed from 8-bit to 16-bit
because 8-bit does not work on IP1000A. 8-bit access is not even
allowed in the TC9020 datasheet (although it worked). 16-bit access
works on both.
Tested that it does not break D-Link DGE-550T (DL-2000 chip, probably
a rebranded TC9020):
vendor=0x1186 device=0x4000 (rev 0x0c)
subsystem vendor=0x1186 device=0x4000
Signed-off-by: Ondrej Zary <linux@rainbow-software.org> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Neil Horman [Mon, 16 Nov 2015 18:09:10 +0000 (13:09 -0500)]
snmp: Remove duplicate OUTMCAST stat increment
the OUTMCAST stat is double incremented, getting bumped once in the mcast code
itself, and again in the common ip output path. Remove the mcast bump, as its
not needed
Validated by the reporter, with good results
Signed-off-by: Neil Horman <nhorman@tuxdriver.com> Reported-by: Claus Jensen <claus.jensen@microsemi.com> CC: Claus Jensen <claus.jensen@microsemi.com> CC: David Miller <davem@davemloft.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Pavel Fedin [Mon, 16 Nov 2015 14:51:34 +0000 (17:51 +0300)]
net: thunder: Check for driver data in nicvf_remove()
In some cases the crash is caused by nicvf_remove() being called from
outside. For example, if we try to feed the device to vfio after the
probe has failed for some reason. So, move the check to better place.
Signed-off-by: Pavel Fedin <p.fedin@samsung.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The ":" is supposed to be preceded by a driver name, but in this
case it is an empty string since the device has no parent.
There are many types of network devices without a parent. The
anonymous warnings for these devices can be hard to debug. Log
the network device name instead in these cases to assist further
debugging.
This is mostly similar to how __netdev_printk() handles orphan
devices.
Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
af_unix: don't append consumed skbs to sk_receive_queue
In case multiple writes to a unix stream socket race we could end up in a
situation where we pre-allocate a new skb for use in unix_stream_sendpage
but have to free it again in the locked section because another skb
has been appended meanwhile, which we must use. Accidentally we didn't
clear the pointer after consuming it and so we touched freed memory
while appending it to the sk_receive_queue. So, clear the pointer after
consuming the skb.
This bug has been found with syzkaller
(http://github.com/google/syzkaller) by Dmitry Vyukov.
Fixes: 869e7c62486e ("net: af_unix: implement stream sendpage support") Reported-by: Dmitry Vyukov <dvyukov@google.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dragos Tatulea [Mon, 16 Nov 2015 09:52:48 +0000 (10:52 +0100)]
net: switchdev: fix return code of fdb_dump stub
rtnl_fdb_dump always expects an index to be returned by the ndo_fdb_dump op,
but when CONFIG_NET_SWITCHDEV is off, it returns an error.
Fix that by returning the given unmodified idx.
A similar fix was 0890cf6cb6ab ("switchdev: fix return value of
switchdev_port_fdb_dump in case of error") but for the CONFIG_NET_SWITCHDEV=y
case.
Fixes: 45d4122ca7cd ("switchdev: add support for fdb add/del/dump via switchdev_port_obj ops.") Signed-off-by: Dragos Tatulea <dragos@endocode.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz [Sun, 15 Nov 2015 13:02:16 +0000 (15:02 +0200)]
bnx2x: Fix VLANs null-pointer for 57710, 57711
Commit 05cc5a39ddb7 "bnx2x: add vlan filtering offload" introduced
a regression in regard for vlans for 57710, 57711 adapters -
Loading 8021q module on a machine with such an adapter would cause
a null pointer dereference, as the driver mistakenly publishes it
has capabilities for vlan CTAG filtering.
Reported-by: Otto Sabart <osabart@redhat.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Masaru Nagai [Sun, 15 Nov 2015 12:34:42 +0000 (21:34 +0900)]
ravb: remove unhandle int cause
This driver does not handle the AVB-DMAC Receive FIFO Warning interrupt
now, so the interrupt should not be enabled.
Signed-off-by: Masaru Nagai <masaru.nagai.vx@renesas.com> Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
raw: increment correct SNMP counters for ICMP messages
Sending ICMP packets with raw sockets ends up in the SNMP counters
logging the type as the first byte of the IPv4 header rather than
the ICMP header. This is fixed by adding the IP Header Length to
the casting into a icmphdr struct.
Signed-off-by: Ben Cartwright-Cox <ben@benjojo.co.uk> Acked-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: fix __netdev_update_features return on ndo_set_features failure
If ndo_set_features fails __netdev_update_features() will return -1 but
this is wrong because it is expected to return 0 if no features were
changed (see netdev_update_features()), which will cause a netdev
notifier to be called without any actual changes. Fix this by returning
0 if ndo_set_features fails.
Fixes: 6cb6a27c45ce ("net: Call netdev_features_change() from netdev_update_features()") CC: Michał Mirosław <mirq-linux@rere.qmqm.pl> Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: fix feature changes on devices without ndo_set_features
When __netdev_update_features() was updated to ensure some features are
disabled on new lower devices, an error was introduced for devices which
don't have the ndo_set_features() method set. Before we'll just set the
new features, but now we return an error and don't set them. Fix this by
returning the old behaviour and setting err to 0 when ndo_set_features
is not present.
Fixes: e7868a85e1b2 ("net/core: ensure features get disabled on new lower devs") CC: Jarod Wilson <jarod@redhat.com> CC: Jiri Pirko <jiri@resnulli.us> CC: Ido Schimmel <idosch@mellanox.com> CC: Sander Eikelenboom <linux@eikelenboom.it> CC: Andy Gospodarek <gospo@cumulusnetworks.com> CC: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Reviewed-by: Andy Gospodarek <gospo@cumulusnetworks.com> Reviewed-by: Jarod Wilson <jarod@redhat.com> Tested-by: Florian Fainelli <f.fainelli@gmail.com> Tested-by: Dave Young <dyoung@redhat.com> Tested-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ivan Vecera [Fri, 13 Nov 2015 10:36:57 +0000 (11:36 +0100)]
be2net: remove unused local rsstable array
Remove rsstable array and its initialization from be_set_rss_hash_opts().
The array became unused after "e255787 be2net: Support for configurable
RSS hash key". The initial RSS table is now filled and stored for later
usage during Rx queue creation.
Signed-off-by: Ivan Vecera <ivecera@redhat.com> Acked-by: Sathya Perla <sathya.perla@avagotech.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Masaru Nagai [Fri, 13 Nov 2015 10:24:49 +0000 (19:24 +0900)]
ravb: Fix int mask value overwritten issue
When RX/TX interrupt for Network Control queue and Best Effort queue
is issued at the same time, the interrupt mask of Network Control
queue will be reset when the mask of Best Effort queue is set.
This patch fixes this problem.
Signed-off-by: Masaru Nagai <masaru.nagai.vx@renesas.com> Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com> Acked-by: Geert Uytterhoeven <geert+renesas@glider.be> Acked-by: Simon Horman <horms+renesas@verge.net.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Pavel Fedin [Fri, 13 Nov 2015 06:46:59 +0000 (09:46 +0300)]
net: smsc911x: Reset PHY during initialization
On certain hardware after software reboot the chip may get stuck and fail
to reinitialize during reset. This can be fixed by ensuring that PHY is
reset too.
Old PHY resetting method required operational MDIO interface, therefore
the chip should have been already set up. In order to be able to function
during probe, it is changed to use PMT_CTRL register.
The problem could be observed on SMDK5410 board.
Signed-off-by: Pavel Fedin <p.fedin@samsung.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Sat, 14 Nov 2015 00:16:18 +0000 (01:16 +0100)]
bpf, arm64: start flushing icache range from header
While recently going over ARM64's BPF code, I noticed that the icache
range we're flushing should start at header already and not at ctx.image.
Reason is that after b569c1c622c5 ("net: bpf: arm64: address randomize
and write protect JIT code"), we also want to make sure to flush the
random-sized trap in front of the start of the actual program (analogous
to x86). No operational differences from user side.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Zi Shen Lim <zlim.lnx@gmail.com> Cc: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Sat, 14 Nov 2015 00:26:53 +0000 (01:26 +0100)]
bpf, arm: start flushing icache range from header
During review I noticed that the icache range we're flushing should
start at header already and not at ctx.image.
Reason is that after 55309dd3d4cd ("net: bpf: arm: address randomize
and write protect JIT code"), we also want to make sure to flush the
random-sized trap in front of the start of the actual program (analogous
to x86). No operational differences from user side.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Tested-by: Nicolas Schichan <nschichan@freebox.fr> Cc: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Yang Shi [Thu, 12 Nov 2015 22:07:46 +0000 (14:07 -0800)]
bpf: samples: exclude asm/sysreg.h for arm64
commit 338d4f49d6f7114a017d294ccf7374df4f998edc
("arm64: kernel: Add support for Privileged Access Never") includes sysreg.h
into futex.h and uaccess.h. But, the inline assembly used by asm/sysreg.h is
incompatible with llvm so it will cause BPF samples build failure for ARM64.
Since sysreg.h is useless for BPF samples, just exclude it from Makefile via
defining __ASM_SYSREG_H.
Signed-off-by: Yang Shi <yang.shi@linaro.org> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Yang Shi [Thu, 12 Nov 2015 21:57:00 +0000 (13:57 -0800)]
arm64: bpf: fix JIT frame pointer setup
BPF fp should point to the top of the BPF prog stack. The original
implementation made it point to the bottom incorrectly.
Move A64_SP to fp before reserve BPF prog stack space.
CC: Zi Shen Lim <zlim.lnx@gmail.com> CC: Xi Wang <xi.wang@gmail.com> Signed-off-by: Yang Shi <yang.shi@linaro.org> Reviewed-by: Zi Shen Lim <zlim.lnx@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Måns Rullgård [Thu, 12 Nov 2015 18:41:12 +0000 (18:41 +0000)]
net: phy: vitesse: add support for VSC8601
This adds support for the Vitesse VSC8601 PHY. Generic functions are
used for everything except interrupt handling.
Signed-off-by: Mans Rullgard <mans@mansr.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Måns Rullgård [Thu, 12 Nov 2015 17:40:20 +0000 (17:40 +0000)]
net: phy: at803x: support interrupt on 8030 and 8035
Commit 77a993942 "phy/at8031: enable at8031 to work on interrupt mode"
added interrupt support for the 8031 PHY but left out the other two
chips supported by this driver.
This patch sets the .ack_interrupt and .config_intr functions for the
8030 and 8035 drivers as well.
Signed-off-by: Mans Rullgard <mans@mansr.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
ip_tunnel: disable preemption when updating per-cpu tstats
Drivers like vxlan use the recently introduced
udp_tunnel_xmit_skb/udp_tunnel6_xmit_skb APIs. udp_tunnel6_xmit_skb
makes use of ip6tunnel_xmit, and ip6tunnel_xmit, after sending the
packet, updates the struct stats using the usual
u64_stats_update_begin/end calls on this_cpu_ptr(dev->tstats).
udp_tunnel_xmit_skb makes use of iptunnel_xmit, which doesn't touch
tstats, so drivers like vxlan, immediately after, call
iptunnel_xmit_stats, which does the same thing - calls
u64_stats_update_begin/end on this_cpu_ptr(dev->tstats).
While vxlan is probably fine (I don't know?), calling a similar function
from, say, an unbound workqueue, on a fully preemptable kernel causes
real issues:
The solution would be to protect the whole
this_cpu_ptr(dev->tstats)/u64_stats_update_begin/end blocks with
disabling preemption and then reenabling it.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 16 Nov 2015 01:16:26 +0000 (20:16 -0500)]
Merge branch 'mv88e6060-fixes'
Neil Armstrong says:
====================
net: dsa: mv88e6060: cleanup and fix setup
This patchset introduces some fixes and a registers addressing cleanup for
the mv88e6060 DSA driver.
The first patch removes the poll_link as mv88e6xxx.
The 3 following patches fixes the setup in regards of the datasheet.
The 2 last patches introduces a clean header and replaces all magic values.
To align with the mv88e6xxx code, add a similar header file
with all the register defines.
The file is based on the mv88e6xxx header for coherency.
Acked-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Acked-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Neil Armstrong [Tue, 10 Nov 2015 15:51:32 +0000 (16:51 +0100)]
net: dsa: mv88e6060: use the correct bit shift for mac0
According to the mv88e6060 datasheet, the first mac byte must
be at position 9 instead of 8 since the bit 8 is used to select
if the mac address must differ for each port for Pause frames.
Use the correct shift and set the same mac address for all port.
Acked-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Neil Armstrong [Tue, 10 Nov 2015 15:51:24 +0000 (16:51 +0100)]
net: dsa: mv88e6060: use the correct MaxFrameSize bit
According to the mv88e6060 datasheet, the MaxFrameSize bit position
is 10 instead of 11 which is reserved.
Use the bit correctly to setup max frame size to 1536.
Acked-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Neil Armstrong [Tue, 10 Nov 2015 15:51:19 +0000 (16:51 +0100)]
net: dsa: mv88e6060: use the correct InitReady bit
According to the mv88e6060 datasheet, the InitReady bit position
is 11 and the polarity is inverted.
Use the bit correctly to detect the end of initialization.
Acked-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Acked-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Neil Armstrong [Tue, 10 Nov 2015 15:51:14 +0000 (16:51 +0100)]
net: dsa: mv88e6060: remove poll_link callback
As of mv88e6xxx remove the poll_link callback since the link
state change polling is now handled by the phylib.
Tested on a mv88e6060 B0 device with a TI DM816X SoC.
Suggested-by: Andrew Lunn <andrew@lunn.ch> Acked-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eran Ben Elisha [Thu, 12 Nov 2015 17:35:29 +0000 (19:35 +0200)]
net/mlx4_core: Fix sleeping while holding spinlock at rem_slave_counters
When cleaning slave's counter resources, we hold a spinlock that
protects the slave's counters list. As part of the clean, we call
__mlx4_clear_if_stat which calls mlx4_alloc_cmd_mailbox which is a
sleepable function.
In order to fix this issue, hold the spinlock, and copy all counter
indices into a temporary array, and release the spinlock. Afterwards,
iterate over this array and free every counter. Repeat this scenario
until the original list is empty (a new counter might have been added
while releasing the counters from the temporary array).
Fixes: b72ca7e96acf ("net/mlx4_core: Reset counters data when freed") Reported-by: Moni Shoua <monis@mellanox.com> Tested-by: Moni Shoua <monis@mellanox.com> Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Achiad Shochat [Thu, 12 Nov 2015 17:35:28 +0000 (19:35 +0200)]
net/mlx5e: Use the right DMA free function on TX path
On xmit path we use skb_frag_dma_map() which is using dma_map_page(),
while upon completion we dma-unmap the skb fragments using
dma_unmap_single() rather than dma_unmap_page().
To fix this, we now save the dma map type on xmit path and use this
info to call the right dma unmap method upon TX completion.
Signed-off-by: Achiad Shochat <achiad@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Doron Tsur [Thu, 12 Nov 2015 17:35:27 +0000 (19:35 +0200)]
net/mlx5e: Max mtu comparison fix
On change mtu the driver compares between hardware queried mtu and
software requested mtu. We need to compare between software
representation of the queried mtu and the requested mtu.
Fixes: facc9699f0fe ('net/mlx5e: Fix HW MTU settings') Signed-off-by: Doron Tsur <doront@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tariq Toukan [Thu, 12 Nov 2015 17:35:26 +0000 (19:35 +0200)]
net/mlx5e: Added self loopback prevention
Prevent outgoing multicast frames from looping back to the RX queue.
By introducing new HW capability self_lb_en_modifiable, which indicates
the support to modify self_lb_en bit in modify_tir command.
When this capability is set we can prevent TIRs from sending back
loopback multicast traffic to their own RQs, by "refreshing TIRs" with
modify_tir command, on every time new channels (SQs/RQs) are created at
device open.
This is needed since TIRs are static and only allocated once on driver
load, and the loopback decision is under their responsibility.
Fixes issues of the kind:
"IPv6: eth2: IPv6 duplicate address fe80::e61d:2dff:fe5c:f2e9 detected!"
The issue is seen since the IPv6 solicitations multicast messages are
loopedback and the network stack thinks they are coming from another host.
Fixes: 5c50368f3831 ("net/mlx5e: Light-weight netdev open/stop") Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed [Thu, 12 Nov 2015 17:35:25 +0000 (19:35 +0200)]
net/mlx5e: Fix inline header size calculation
mlx5e_get_inline_hdr_size didn't take into account the vlan insertion
into the inline WQE segment.
This could lead to max inline violation in cases where
skb_headlen(skb) + VLAN_HLEN >= sq->max_inline.
Fixes: 3ea4891db8d0 ("net/mlx5e: Fix LSO vlan insertion") Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Achiad Shochat <achiad@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 12 Nov 2015 17:14:12 +0000 (09:14 -0800)]
ipvs: use skb_to_full_sk() helper
SYNACK packets might be attached to request sockets.
Use skb_to_full_sk() helper to avoid illegal accesses to
inet_sk(skb->sk)
Fixes: ca6fb0651883 ("tcp: attach SYNACK messages to request sockets instead of listener") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Sander Eikelenboom <linux@eikelenboom.it> Acked-by: Julian Anastasov <ja@ssi.bg> Acked-by: Simon Horman <horms@verge.net.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Pavel Fedin [Thu, 12 Nov 2015 11:55:18 +0000 (14:55 +0300)]
net: thunder: Fix crash upon shutdown after failed probe
If device probe fails, driver remains bound to the PCI device. However,
driver data has been reset to NULL. This causes crash upon dereferencing
it in nicvf_remove()
Signed-off-by: Pavel Fedin <p.fedin@samsung.com> Signed-off-by: David S. Miller <davem@davemloft.net>
lucien [Thu, 12 Nov 2015 05:07:07 +0000 (13:07 +0800)]
sctp: translate host order to network order when setting a hmacid
now sctp auth cannot work well when setting a hmacid manually, which
is caused by that we didn't use the network order for hmacid, so fix
it by adding the transformation in sctp_auth_ep_set_hmacs.
even we set hmacid with the network order in userspace, it still
can't work, because of this condition in sctp_auth_ep_set_hmacs():
if (id > SCTP_AUTH_HMAC_ID_MAX)
return -EOPNOTSUPP;
so this wasn't working before and thus it won't break compatibility.
Fixes: 65b07e5d0d09 ("[SCTP]: API updates to suport SCTP-AUTH extensions.") Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Acked-by: Vlad Yasevich <vyasevich@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 15 Nov 2015 23:00:48 +0000 (18:00 -0500)]
Merge branch 'packet-fixes'
Daniel Borkmann says:
====================
packet fixes
Fixes a couple of issues in packet sockets, i.e. on TX ring side. See
individual patches for details.
v2 -> v3:
- First two patches unchanged, kept Jason's Ack
- Reworked 3rd patch and split into 3:
- check for dev type as discussed with Willem
- infer skb->protocol
- fix max len for dgram
v1 -> v2:
- Added patch 2 as suggested by Dave
- Rest is unchanged from previous submission
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Wed, 11 Nov 2015 22:25:44 +0000 (23:25 +0100)]
packet: fix tpacket_snd max frame len
Since it's introduction in commit 69e3c75f4d54 ("net: TX_RING and
packet mmap"), TX_RING could be used from SOCK_DGRAM and SOCK_RAW
side. When used with SOCK_DGRAM only, the size_max > dev->mtu +
reserve check should have reserve as 0, but currently, this is
unconditionally set (in it's original form as dev->hard_header_len).
I think this is not correct since tpacket_fill_skb() would then
take dev->mtu and dev->hard_header_len into account for SOCK_DGRAM,
the extra VLAN_HLEN could be possible in both cases. Presumably, the
reserve code was copied from packet_snd(), but later on missed the
check. Make it similar as we have it in packet_snd().
Fixes: 69e3c75f4d54 ("net: TX_RING and packet mmap") Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Wed, 11 Nov 2015 22:25:43 +0000 (23:25 +0100)]
packet: infer protocol from ethernet header if unset
In case no struct sockaddr_ll has been passed to packet
socket's sendmsg() when doing a TX_RING flush run, then
skb->protocol is set to po->num instead, which is the protocol
passed via socket(2)/bind(2).
Applications only xmitting can go the path of allocating the
socket as socket(PF_PACKET, <mode>, 0) and do a bind(2) on the
TX_RING with sll_protocol of 0. That way, register_prot_hook()
is neither called on creation nor on bind time, which saves
cycles when there's no interest in capturing anyway.
That leaves us however with po->num 0 instead and therefore
the TX_RING flush run sets skb->protocol to 0 as well. Eric
reported that this leads to problems when using tools like
trafgen over bonding device. I.e. the bonding's hash function
could invoke the kernel's flow dissector, which depends on
skb->protocol being properly set. In the current situation, all
the traffic is then directed to a single slave.
Fix it up by inferring skb->protocol from the Ethernet header
when not set and we have ARPHRD_ETHER device type. This is only
done in case of SOCK_RAW and where we have a dev->hard_header_len
length. In case of ARPHRD_ETHER devices, this is guaranteed to
cover ETH_HLEN, and therefore being accessed on the skb after
the skb_store_bits().
Reported-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Wed, 11 Nov 2015 22:25:42 +0000 (23:25 +0100)]
packet: only allow extra vlan len on ethernet devices
Packet sockets can be used by various net devices and are not
really restricted to ARPHRD_ETHER device types. However, when
currently checking for the extra 4 bytes that can be transmitted
in VLAN case, our assumption is that we generally probe on
ARPHRD_ETHER devices. Therefore, before looking into Ethernet
header, check the device type first.
This also fixes the issue where non-ARPHRD_ETHER devices could
have no dev->hard_header_len in TX_RING SOCK_RAW case, and thus
the check would test unfilled linear part of the skb (instead
of non-linear).
Fixes: 57f89bfa2140 ("network: Allow af_packet to transmit +4 bytes for VLAN packets.") Fixes: 52f1454f629f ("packet: allow to transmit +4 byte in TX_RING slot for VLAN case") Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Wed, 11 Nov 2015 22:25:41 +0000 (23:25 +0100)]
packet: always probe for transport header
We concluded that the skb_probe_transport_header() should better be
called unconditionally. Avoiding the call into the flow dissector has
also not really much to do with the direct xmit mode.
While it seems that only virtio_net code makes use of GSO from non
RX/TX ring packet socket paths, we should probe for a transport header
nevertheless before they hit devices.
Reference: http://thread.gmane.org/gmane.linux.network/386173/ Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Jason Wang <jasowang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Wed, 11 Nov 2015 22:25:40 +0000 (23:25 +0100)]
packet: do skb_probe_transport_header when we actually have data
In tpacket_fill_skb() commit c1aad275b029 ("packet: set transport
header before doing xmit") and later on 40893fd0fd4e ("net: switch
to use skb_probe_transport_header()") was probing for a transport
header on the skb from a ring buffer slot, but at a time, where
the skb has _not even_ been filled with data yet. So that call into
the flow dissector is pretty useless. Lets do it after we've set
up the skb frags.
Fixes: c1aad275b029 ("packet: set transport header before doing xmit") Reported-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Jason Wang <jasowang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Kamal Mostafa [Wed, 11 Nov 2015 22:24:27 +0000 (14:24 -0800)]
tools/net: Use include/uapi with __EXPORTED_HEADERS__
Use the local uapi headers to keep in sync with "recently" added #define's
(e.g. SKF_AD_VLAN_TPID). Refactored CFLAGS, and bpf_asm doesn't need -I.
Fixes: 3f356385e8a4 ("filter: bpf_asm: add minimal bpf asm tool") Signed-off-by: Kamal Mostafa <kamal@canonical.com> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 15 Nov 2015 22:15:50 +0000 (17:15 -0500)]
Merge branch 'ipv6-route-fixes'
Martin KaFai Lau says:
====================
ipv6: Fixes for pmtu update and DST_NOCACHE route
This patchset fixes:
1. An oops during IPv6 pmtu update on a IPv4 GRE running
in an IPSec setup
2. Misc fixes on DST_NOCACHE route
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Martin KaFai Lau [Wed, 11 Nov 2015 19:51:08 +0000 (11:51 -0800)]
ipv6: Check rt->dst.from for the DST_NOCACHE route
All DST_NOCACHE rt6_info used to have rt->dst.from set to
its parent.
After commit 8e3d5be73681 ("ipv6: Avoid double dst_free"),
DST_NOCACHE is also set to rt6_info which does not have
a parent (i.e. rt->dst.from is NULL).
This patch catches the rt->dst.from == NULL case.
Fixes: 8e3d5be73681 ("ipv6: Avoid double dst_free") Signed-off-by: Martin KaFai Lau <kafai@fb.com> Cc: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Martin KaFai Lau [Wed, 11 Nov 2015 19:51:07 +0000 (11:51 -0800)]
ipv6: Check expire on DST_NOCACHE route
Since the expires of the DST_NOCACHE rt can be set during
the ip6_rt_update_pmtu(), we also need to consider the expires
value when doing ip6_dst_check().
This patches creates __rt6_check_expired() to only
check the expire value (if one exists) of the current rt.
In rt6_dst_from_check(), it adds __rt6_check_expired() as
one of the condition check.
Signed-off-by: Martin KaFai Lau <kafai@fb.com> Cc: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Martin KaFai Lau [Wed, 11 Nov 2015 19:51:06 +0000 (11:51 -0800)]
ipv6: Avoid creating RTF_CACHE from a rt that is not managed by fib6 tree
The original bug report:
https://bugzilla.redhat.com/show_bug.cgi?id=1272571
The setup has a IPv4 GRE tunnel running in a IPSec. The bug
happens when ndisc starts sending router solicitation at the gre
interface. The simplified oops stack is like:
The rt passed to ip6_rt_update_pmtu() is created by
icmp6_dst_alloc() and it is not managed by the fib6 tree,
so its rt6i_table == NULL. When __ip6_rt_update_pmtu() creates
a RTF_CACHE clone, the newly created clone also has rt6i_table == NULL
and it causes the ip6_ins_rt() oops.
During pmtu update, we only want to create a RTF_CACHE clone
from a rt which is currently managed (or owned) by the
fib6 tree. It means either rt->rt6i_node != NULL or
rt is a RTF_PCPU clone.
It is worth to note that rt6i_table may not be NULL even it is
not (yet) managed by the fib6 tree (e.g. addrconf_dst_alloc()).
Hence, rt6i_node is a better check instead of rt6i_table.
Fixes: 45e4fd26683c ("ipv6: Only create RTF_CACHE routes after encountering pmtu") Signed-off-by: Martin KaFai Lau <kafai@fb.com> Reported-by: Chris Siebenmann <cks-rhbugzilla@cs.toronto.edu> Cc: Chris Siebenmann <cks-rhbugzilla@cs.toronto.edu> Cc: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Ian King [Wed, 11 Nov 2015 15:22:40 +0000 (15:22 +0000)]
fjes: fix inconsistent indenting
minor change, indenting is one tab out.
Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
af-unix: fix use-after-free with concurrent readers while splicing
During splicing an af-unix socket to a pipe we have to drop all
af-unix socket locks. While doing so we allow another reader to enter
unix_stream_read_generic which can read, copy and finally free another
skb. If exactly this skb is just in process of being spliced we get a
use-after-free report by kasan.
First, we must make sure to not have a free while the skb is used during
the splice operation. We simply increment its use counter before unlocking
the reader lock.
Stream sockets have the nice characteristic that we don't care about
zero length writes and they never reach the peer socket's queue. That
said, we can take the UNIXCB.consumed field as the indicator if the
skb was already freed from the socket's receive queue. If the skb was
fully consumed after we locked the reader side again we know it has been
dropped by a second reader. We indicate a short read to user space and
abort the current splice operation.
This bug has been found with syzkaller
(http://github.com/google/syzkaller) by Dmitry Vyukov.
Fixes: 2b514574f7e8 ("net: af_unix: implement splice for stream af_unix sockets") Reported-by: Dmitry Vyukov <dvyukov@google.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Eric Dumazet <eric.dumazet@gmail.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net>
and when this is passed into a function that takes an unsigned int type,
gcc warns about the signed overflow and the loss of the upper 32-bits that
are all ones.
This patch adds 'ul' type modifiers to the literal numbers passed in
here, so now the expression remains an 'unsigned long' with the upper
bits all zero, and that avoids the signed overflow and the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Fixes: b1c17215d718 ("stmmac: add ipq806x glue layer") Signed-off-by: David S. Miller <davem@davemloft.net>
The following patchset contains Netfilter fixes for your net tree. This
large batch that includes fixes for ipset, netfilter ingress, nf_tables
dynamic set instantiation and a longstanding Kconfig dependency problem.
More specifically, they are:
1) Add missing check for empty hook list at the ingress hook, from
Florian Westphal.
2) Input and output interface are swapped at the ingress hook,
reported by Patrick McHardy.
3) Resolve ipset extension alignment issues on ARM, patch from Jozsef
Kadlecsik.
4) Fix bit check on bitmap in ipset hash type, also from Jozsef.
5) Release buckets when all entries have expired in ipset hash type,
again from Jozsef.
6) Oneliner to initialize conntrack tuple object in the PPTP helper,
otherwise the conntrack lookup may fail due to random bits in the
structure holes, patch from Anthony Lineham.
7) Silence a bogus gcc warning in nfnetlink_log, from Arnd Bergmann.
8) Fix Kconfig dependency problems with TPROXY, socket and dup, also
from Arnd.
9) Add __netdev_alloc_pcpu_stats() to allow creating percpu counters
from atomic context, this is required by the follow up fix for
nf_tables.
10) Fix crash from the dynamic set expression, we have to add new clone
operation that should be defined when a simple memcpy is not enough.
This resolves a crash when using per-cpu counters with new Patrick
McHardy's flow table nft support.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
françois romieu [Wed, 11 Nov 2015 22:35:18 +0000 (23:35 +0100)]
r8169: fix kasan reported skb use-after-free.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com> Reported-by: Dave Jones <davej@codemonkey.org.uk> Fixes: d7d2d89d4b0af ("r8169: Add software counter for multicast packages") Acked-by: Eric Dumazet <edumazet@google.com> Acked-by: Corinna Vinschen <vinschen@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Wed, 11 Nov 2015 05:14:23 +0000 (21:14 -0800)]
Merge branch 'akpm' (patches from Andrew)
Merge final patch-bomb from Andrew Morton:
"Various leftovers, mainly Christoph's pci_dma_supported() removals"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
pci: remove pci_dma_supported
usbnet: remove ifdefed out call to dma_supported
kaweth: remove ifdefed out call to dma_supported
sfc: don't call dma_supported
nouveau: don't call pci_dma_supported
netup_unidvb: use pci_set_dma_mask insted of pci_dma_supported
cx23885: use pci_set_dma_mask insted of pci_dma_supported
cx25821: use pci_set_dma_mask insted of pci_dma_supported
cx88: use pci_set_dma_mask insted of pci_dma_supported
saa7134: use pci_set_dma_mask insted of pci_dma_supported
saa7164: use pci_set_dma_mask insted of pci_dma_supported
tw68-core: use pci_set_dma_mask insted of pci_dma_supported
pcnet32: use pci_set_dma_mask insted of pci_dma_supported
lib/string.c: add ULL suffix to the constant definition
hugetlb: trivial comment fix
selftests/mlock2: add ULL suffix to 64-bit constants
selftests/mlock2: add missing #define _GNU_SOURCE
Linus Torvalds [Wed, 11 Nov 2015 05:06:50 +0000 (21:06 -0800)]
Merge branch 'kconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild
Pull kconfig updates from Michal Marek:
- 'make xconfig' ported to Qt5, dropping support for Qt3
- merge_config.sh supports a single-input-file mode and also respects
$KCONFIG_CONFIG
- Fix for incorrect display of >= and > in dependency expressions
* 'kconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild: (44 commits)
Add current selection check.
Use pkg-config to find Qt 4 and 5 instead of direct qmake
kconfig: Fix copy&paste error
kconfig/merge_config.sh: Accept a single file
kconfig/merge_config.sh: Support KCONFIG_CONFIG
Update the buildsystem for KConfig finding Qt
Port xconfig to Qt5 - Update copyright.
Port xconfig to Qt5 - Fix goParent issue.
Port xconfig to Qt5 - on Back clicked, deselect old item.
Port xconfig to Qt5 - Add(back) one click checkbox toggle.
Port xconfig to Qt5 - Add(back) lineedit editing.
Port xconfig to Qt5 - Remove some commented code.
Port xconfig to Qt5 - Source format.
Port xconfig to Qt5 - Add horizontal scrollbar, and scroll per pixel.
Port xconfig to Qt5 - Change ConfigItem constructor parent type.
Port xconfig to Qt5 - Disable ConfigList soring
Port xconfig to Qt5 - Remove ConfigList::updateMenuList template.
Port xconfig to Qt5 - Add ConfigList::mode to initializer list.
Port xconfig to Qt5 - Add ConfigItem::nextItem to initializer list.
Port xconfig to Qt5 - Tree widget set column titles.
...
Linus Torvalds [Wed, 11 Nov 2015 04:55:37 +0000 (20:55 -0800)]
Merge branch 'kbuild' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild
Pull kbuild update from Michal Marek:
"The kbuild branch for v4.4-rc1 only has one commit: A new make
kselftest-clean target cleans tools/testing/selftests"
* 'kbuild' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
kselftest: add kselftest-clean rule
Linus Torvalds [Wed, 11 Nov 2015 04:46:45 +0000 (20:46 -0800)]
Merge tag 'linux-kselftest-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull kselftest updates from Shuah Khan:
"This 12 patch update for 4.4-rc1 consists of a new pstore test and
fixes to existing tests"
* tag 'linux-kselftest-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
selftests: breakpoint: Actually build it
selftests: vm: Try harder to allocate huge pages
selftests: Make scripts executable
selftests: kprobe: Choose an always-defined function to probe
selftests: memfd: Stop unnecessary rebuilds
selftests: Add missing #include directives
selftests/seccomp: Be more precise with syscall arguments.
selftests/seccomp: build and pass on arm64
selftests: memfd_test: Revised STACK_SIZE to make it 16-byte aligned
selftests/pstore: add pstore test scripts going with reboot
selftests/pstore: add pstore test script for pre-reboot
selftests: add .gitignore for efivarfs
Linus Torvalds [Wed, 11 Nov 2015 04:37:28 +0000 (20:37 -0800)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Two build fixes, one for VC4, one for nouveau where the ARM only code
is doing something a bit strange. While people are discussing that,
just workaround it and fix the build for now. The code in question
will never get used on anything non-ARM anyways.
Also one fix for AST that SuSE had been hiding in their kernel, that
allows all fbdev apps to work on that driver"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/nouveau: fix build failures on all non ARM.
drm/ast: Initialized data needed to map fbdev memory
drm/vc4: Add dependency on HAVE_DMA_ATTRS, and select DRM_GEM_CMA_HELPER
Dave Airlie [Mon, 9 Nov 2015 22:36:59 +0000 (08:36 +1000)]
drm/nouveau: fix build failures on all non ARM.
gk20a is an ARM only GPU, so we can just do the correct thing on
ARM but fail on other architectures. The other option was to use
SWIOTLB as the define, which means phys_to_page exists, but
this seems clearer.
Egbert Eich [Wed, 11 Jun 2014 12:59:55 +0000 (14:59 +0200)]
drm/ast: Initialized data needed to map fbdev memory
Due to a missing initialization there was no way to map fbdev memory.
Thus for example using the Xserver with the fbdev driver failed.
This fix adds initialization for fix.smem_start and fix.smem_len
in the fb_info structure, which fixes this problem.
Requested-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: stable@vger.kernel.org Signed-off-by: Egbert Eich <eich@suse.de>
[pulled from SuSE tree by me - airlied] Signed-off-by: Dave Airlie <airlied@redhat.com>
1) Fix null deref in xt_TEE netfilter module, from Eric Dumazet.
2) Several spots need to get to the original listner for SYN-ACK
packets, most spots got this ok but some were not. Whilst covering
the remaining cases, create a helper to do this. From Eric Dumazet.
3) Missiing check of return value from alloc_netdev() in CAIF SPI code,
from Rasmus Villemoes.
4) Don't sleep while != TASK_RUNNING in macvtap, from Vlad Yasevich.
5) Use after free in mvneta driver, from Justin Maggard.
6) Fix race on dst->flags access in dst_release(), from Eric Dumazet.
7) Add missing ZLIB_INFLATE dependency for new qed driver. From Arnd
Bergmann.
8) Fix multicast getsockopt deadlock, from WANG Cong.
9) Fix deadlock in btusb, from Kuba Pawlak.
10) Some ipv6_add_dev() failure paths were not cleaning up the SNMP6
counter state. From Sabrina Dubroca.
11) Fix packet_bind() race, which can cause lost notifications, from
Francesco Ruggeri.
12) Fix MAC restoration in qlcnic driver during bonding mode changes,
from Jarod Wilson.
13) Revert bridging forward delay change which broke libvirt and other
userspace things, from Vlad Yasevich.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (65 commits)
Revert "bridge: Allow forward delay to be cfgd when STP enabled"
bpf_trace: Make dependent on PERF_EVENTS
qed: select ZLIB_INFLATE
net: fix a race in dst_release()
net: mvneta: Fix memory use after free.
net: Documentation: Fix default value tcp_limit_output_bytes
macvtap: Resolve possible __might_sleep warning in macvtap_do_read()
mvneta: add FIXED_PHY dependency
net: caif: check return value of alloc_netdev
net: hisilicon: NET_VENDOR_HISILICON should depend on HAS_DMA
drivers: net: xgene: fix RGMII 10/100Mb mode
netfilter: nft_meta: use skb_to_full_sk() helper
net_sched: em_meta: use skb_to_full_sk() helper
sched: cls_flow: use skb_to_full_sk() helper
netfilter: xt_owner: use skb_to_full_sk() helper
smack: use skb_to_full_sk() helper
net: add skb_to_full_sk() helper and use it in selinux_netlbl_skbuff_setsid()
bpf: doc: correct arch list for supported eBPF JIT
dwc_eth_qos: Delete an unnecessary check before the function call "of_node_put"
bonding: fix panic on non-ARPHRD_ETHER enslave failure
...
Linus Torvalds [Wed, 11 Nov 2015 01:23:49 +0000 (17:23 -0800)]
Merge branch 'for-4.4/io-poll' of git://git.kernel.dk/linux-block
Pull block IO poll support from Jens Axboe:
"Various groups have been doing experimentation around IO polling for
(really) fast devices. The code has been reviewed and has been
sitting on the side for a few releases, but this is now good enough
for coordinated benchmarking and further experimentation.
Currently O_DIRECT sync read/write are supported. A framework is in
the works that allows scalable stats tracking so we can auto-tune
this. And we'll add libaio support as well soon. Fow now, it's an
opt-in feature for test purposes"
* 'for-4.4/io-poll' of git://git.kernel.dk/linux-block:
direct-io: be sure to assign dio->bio_bdev for both paths
directio: add block polling support
NVMe: add blk polling support
block: add block polling support
blk-mq: return tag/queue combo in the make_request_fn handlers
block: change ->make_request_fn() and users to return a queue cookie
Linus Torvalds [Wed, 11 Nov 2015 00:35:06 +0000 (16:35 -0800)]
Merge tag 'upstream-4.4-rc1' of git://git.infradead.org/linux-ubifs
Pull UBI/UBIFS updates from Richard Weinberger:
- access time support for UBIFS by Dongsheng Yang
- random cleanups and bug fixes all over the place
* tag 'upstream-4.4-rc1' of git://git.infradead.org/linux-ubifs:
ubifs: introduce UBIFS_ATIME_SUPPORT to ubifs
ubifs: make ubifs_[get|set]xattr atomic
UBIFS: Delete unnecessary checks before the function call "iput"
UBI: Remove in vain semicolon
UBI: Fastmap: Fix PEB array type
UBIFS: Fix possible memory leak in ubifs_readdir()
fs/ubifs: remove unnecessary new_valid_dev check
ubi: fastmap: Implement produce_free_peb()
UBIFS: print verbose message when rescanning a corrupted node
UBIFS: call dbg_is_power_cut() instead of reading c->dbg->pc_happened
UBI: drop null test before destroy functions
UBI: Update comments to reflect UBI_METAONLY flag
UBI: Fix debug message
UBI: Fix typo in comment
UBI: Fastmap: Simplify expression
UBIFS: fix a typo in comment of ubifs_budget_req
UBIFS: use kmemdup rather than duplicating its implementation
Linus Torvalds [Wed, 11 Nov 2015 00:33:37 +0000 (16:33 -0800)]
Merge branch 'for-linus-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml
Pull UML updates from Richard Weinberger:
- a new hrtimer based clocksource by Anton Ivanov
- ptrace() enhancments by Richard Weinberger
- random cleanups and bug fixes all over the place
* 'for-linus-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml:
um: Switch clocksource to hrtimers
um: net: replace GFP_KERNEL with GFP_ATOMIC when spinlock is held
um: Report host OOM more nicely
um: Simplify STUB_DATA loading
um: Remove dead symbol from i386 syscall stub
um: Remove dead code from x86_64 syscall stub
um: Get rid of open coded NR_SYSCALLS
um: Store syscall number after syscall_trace_enter()
um: Define PTRACE_OLDSETOPTIONS
pcnet32: use pci_set_dma_mask insted of pci_dma_supported
All drivers should be using dma_set_mask / pci_set_dma_mask to try to
set the dma mask instead of just querying it. Without that some iommu
implementations may not work.
pci_dma_supported is removed entirely, but dma_supported stays for
dma_ops implementations for now.
This patch (of 15):
This ensures the dma mask that is supported by the driver is recorded
in the device structure.
Signed-off-by: Christoph Hellwig <hch@lst.de> Acked-by: Don Fry <pcnet32@frontier.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: "James E.J. Bottomley" <jejb@parisc-linux.org> Cc: Alan Stern <stern@rowland.harvard.edu> Cc: Alexandre Courbot <acourbot@nvidia.com> Cc: Alexey Khoroshilov <khoroshilov@ispras.ru> Cc: Ben Skeggs <bskeggs@redhat.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Dave Airlie <airlied@redhat.com> Cc: David Airlie <airlied@linux.ie> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Hans Verkuil <hverkuil@xs4all.nl> Cc: Helge Deller <deller@gmx.de> Cc: Jiri Slaby <jslaby@suse.com> Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com> Cc: Pawel Osciak <pawel@osciak.com> Cc: Sakari Ailus <sakari.ailus@linux.intel.com> Cc: Sergey Kozlov <serjk@netup.ru> Cc: Shradha Shah <sshah@solarflare.com> Cc: Solarflare linux maintainers <linux-net-drivers@solarflare.com> Cc: Steven Toth <stoth@kernellabs.com> Cc: Thierry Reding <treding@nvidia.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
selftests/mlock2: add ULL suffix to 64-bit constants
On 32-bit (e.g. m68k):
mlock2-tests.c: In function 'lock_check':
mlock2-tests.c:293: warning: integer constant is too large for 'long' type
mlock2-tests.c:294: warning: integer constant is too large for 'long' type
mlock2-tests.c:299: warning: integer constant is too large for 'long' type
...
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Acked-by: Eric B Munson <emunson@akamai.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Wed, 11 Nov 2015 00:24:25 +0000 (16:24 -0800)]
Merge tag 'metag-for-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/metag
Pull metag arch updates from James Hogan:
"A fix for 4KiB stacks with SMP, and a change of maintenance status to
'Odd Fixes'"
* tag 'metag-for-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/metag:
MAINTAINERS: Change Meta arch port status to Odd Fixes
metag: Turn irq_ctx_* macros into static inlines
metag: SMP: Fix 4KiB stack setup on secondary CPUs
Linus Torvalds [Tue, 10 Nov 2015 23:08:32 +0000 (15:08 -0800)]
Merge tag 'armsoc-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC defconfig updates from Olof Johansson:
"Defconfig updates are kept separate from other branches mostly to
avoid conflicts between the different categories (driver branch
enabling something that has context conflict with SoC options, etc).
A lot of this again is scattered across the various hardware
platforms. multi_v7_defconfig, our "generic" config for most 32-bit
platforms has been gone through by Marvell Berlin maintainers and
added most options they need to run on their hardware. Broadcom NSP
is also added there, and the new Atmel SAMA5D2 (added last release).
Rockchip also has display and other devices supported in that config.
In addition to that, the usual small churn of new options being added
here and there"
* tag 'armsoc-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (45 commits)
ARM: multi_v7_defconfig: enable UniPhier I2C drivers
ARM: multi_v7_defconfig: Enable rtl8152 ethernet driver for Odroid-XU4
ARM: exynos_defconfig: Enable rtl8152 ethernet driver for Odroid-XU4
ARM: exynos_defconfig: Enable WiFi-Ex as a module instead built-in
ARM: exynos_defconfig: Disable simplefb support
ARM: exynos_defconfig: Enable LEDS for Odroid-XU3/XU4
ARM: multi_v7_defconfig: Enable DWC2 USB driver and USB ethernet gadget
ARM: exynos_defconfig: Enable DWC2 USB driver and USB ethernet gadget
ARM: exynos_defconfig: Enable USB Video Class support
ARM: multi_v7_defconfig: improve multi_v7_defconfig support for Berlin
ARM: tegra: Update multi_v7_defconfig
ARM: multi_v7_defconfig: Add Atmel SDHCI device
ARM: multi_v7_defconfig: Add Atmel Flexcom device
ARM: multi_v7_defconfig: Add Atmel SAMA5D2 SoC
ARM: at91/defconfig: add sama5d2 and its new devices to sama5 defconfig
ARM: at91/defconfig: update at91_dt defconfig
ARM: at91/defconfig: update sama5 defconfig
ARM: configs: Enable FIXED_PHY in multi_v7 defconfig
ARM: configs: update lpc18xx defconfig
ARM: socfpga_defconfig: enable fpga manager
...
Linus Torvalds [Tue, 10 Nov 2015 23:06:26 +0000 (15:06 -0800)]
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Olof Johansson:
"As usual, this is the massive branch we have for each release. Lots
of various updates and additions of hardware descriptions on existing
hardware, as well as the usual additions of new boards and SoCs.
This is also the first release where we've started mixing 64- and
32-bit DT updates in one branch.
(Specific details on what's actually here and new is pretty easy to
tell from the diffstat, so there's little point in duplicating listing
it here)"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (499 commits)
ARM: dts: uniphier: add system-bus-controller nodes
ARM64: juno: disable NOR flash node by default
ARM: dts: uniphier: add outer cache controller nodes
arm64: defconfig: Enable PCI generic host bridge by default
arm64: Juno: Add support for the PCIe host bridge on Juno R1
Documentation: of: Document the bindings used by Juno R1 PCIe host bridge
ARM: dts: uniphier: add I2C aliases for ProXstream2 boards
dts/Makefile: Add build support for LS2080a QDS & RDB board DTS
dts/ls2080a: Add DTS support for LS2080a QDS & RDB boards
dts/ls2080a: Update Simulator DTS to add support of various peripherals
dts/ls2080a: Remove text about writing to Free Software Foundation
dts/ls2080a: Update DTSI to add support of various peripherals
doc: DTS: Update DWC3 binding to provide reference to generic bindings
doc/bindings: Update GPIO devicetree binding documentation for LS2080A
Documentation/dts: Move FSL board-specific bindings out of /powerpc
Documentation: DT: Add entry for FSL LS2080A QDS and RDB boards
arm64: Rename FSL LS2085A SoC support code to LS2080A
arm64: Use generic Layerscape SoC family naming
ARM: dts: uniphier: add ProXstream2 Vodka board support
ARM: dts: uniphier: add ProXstream2 Gentil board support
...
Linus Torvalds [Tue, 10 Nov 2015 23:00:03 +0000 (15:00 -0800)]
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"As we've enabled multiplatform kernels on ARM, and greatly done away
with the contents under arch/arm/mach-*, there's still need for
SoC-related drivers to go somewhere.
Many of them go in through other driver trees, but we still have
drivers/soc to hold some of the "doesn't fit anywhere" lowlevel code
that might be shared between ARM and ARM64 (or just in general makes
sense to not have under the architecture directory).
This branch contains mostly such code:
- Drivers for qualcomm SoCs for SMEM, SMD and SMD-RPM, used to
communicate with power management blocks on these SoCs for use by
clock, regulator and bus frequency drivers.
- Allwinner Reduced Serial Bus driver, again used to communicate with
PMICs.
- Drivers for ARM's SCPI (System Control Processor). Not to be
confused with PSCI (Power State Coordination Interface). SCPI is
used to communicate with the assistant embedded cores doing power
management, and we have yet to see how many of them will implement
this for their hardware vs abstracting in other ways (or not at all
like in the past).
- To make confusion between SCPI and PSCI more likely, this release
also includes an update of PSCI to interface version 1.0.
- Rockchip support for power domains.
- A driver to talk to the firmware on Raspberry Pi"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (57 commits)
soc: qcom: smd-rpm: Correct size of outgoing message
bus: sunxi-rsb: Add driver for Allwinner Reduced Serial Bus
bus: sunxi-rsb: Add Allwinner Reduced Serial Bus (RSB) controller bindings
ARM: bcm2835: add mutual inclusion protection
drivers: psci: make PSCI 1.0 functions initialization version dependent
dt-bindings: Correct paths in Rockchip power domains binding document
soc: rockchip: power-domain: don't try to print the clock name in error case
soc: qcom/smem: add HWSPINLOCK dependency
clk: berlin: add cpuclk
ARM: berlin: dts: add CLKID_CPU for BG2Q
ARM: bcm2835: Add the Raspberry Pi firmware driver
soc: qcom: smem: Move RPM message ram out of smem DT node
soc: qcom: smd-rpm: Correct the active vs sleep state flagging
soc: qcom: smd: delete unneeded of_node_put
firmware: qcom-scm: build for correct architecture level
soc: qcom: smd: Correct SMEM items for upper channels
qcom-scm: add missing prototype for qcom_scm_is_available()
qcom-scm: fix endianess issue in __qcom_scm_is_call_available
soc: qcom: smd: Reject send of too big packets
soc: qcom: smd: Handle big endian CPUs
...
Linus Torvalds [Tue, 10 Nov 2015 22:56:23 +0000 (14:56 -0800)]
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Olof Johansson:
"New and/or improved SoC support for this release:
Marvell Berlin:
- Enable standard DT-based cpufreq
- Add CPU hotplug support
Freescale:
- Ethernet init for i.MX7D
- Suspend/resume support for i.MX6UL
Allwinner:
- Support for R8 chipset (used on NTC's $9 C.H.I.P board)
Mediatek:
- SMP support for some platforms
Uniphier:
- L2 support
- Cleaned up SMP support, etc.
plus a handful of other patches around above functionality, and a few
other smaller changes"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (42 commits)
ARM: uniphier: rework SMP operations to use trampoline code
ARM: uniphier: add outer cache support
Documentation: EXYNOS: Update bootloader interface on exynos542x
ARM: mvebu: add broken-idle option
ARM: orion5x: use mac_pton() helper
ARM: at91: pm: at91_pm_suspend_in_sram() must be 8-byte aligned
ARM: sunxi: Add R8 support
ARM: digicolor: select pinctrl/gpio driver
arm: berlin: add CPU hotplug support
arm: berlin: use non-self-cleared reset register to reset cpu
ARM: mediatek: add smp bringup code
ARM: mediatek: enable gpt6 on boot up to make arch timer working
soc: mediatek: Fix random hang up issue while kernel init
soc: ti: qmss: make acc queue support optional in the driver
soc: ti: add firmware file name as part of the driver
Documentation: dt: soc: Add description for knav qmss driver
ARM: S3C64XX: Use PWM lookup table for mach-smartq
ARM: S3C64XX: Use PWM lookup table for mach-hmt
ARM: S3C64XX: Use PWM lookup table for mach-crag6410
ARM: S3C64XX: Use PWM lookup table for smdk6410
...
Linus Torvalds [Tue, 10 Nov 2015 22:48:36 +0000 (14:48 -0800)]
Merge tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"Again we have a sizable (but not huge) cleanup branch with a net delta
of about -3k lines.
Main contents here is:
- A bunch of development/cleanup of a few PXA boards
- Removal of bockw platforms on shmobile, since the platform has now
gone completely multiplatform. Whee!
- move of the 32kHz timer on OMAP to a proper timesource
- Misc cleanup of older OMAP material (incl removal of one board
file)
- Switch over to new common PWM lookup support for several platforms
There's also a handful of other cleanups across the tree, but the
above are the major pieces"
* tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (103 commits)
ARM: OMAP3: hwmod data: Remove legacy mailbox data and addrs
ARM: DRA7: hwmod data: Remove spinlock hwmod addrs
ARM: OMAP4: hwmod data: Remove spinlock hwmod addrs
ARM: DRA7/AM335x/AM437x: hwmod: Remove gpmc address space from hwmod data
ARM: Remove __ref on hotplug cpu die path
ARM: Remove open-coded version of IRQCHIP_DECLARE
arm: omap2: board-generic: use omap4_local_timer_init for AM437x
ARM: DRA7/AM335x/AM437x: hwmod: Remove elm address space from hwmod data
ARM: OMAP: Remove duplicated operand in OR operation
clocksource: ti-32k: make it depend on GENERIC_CLOCKSOURCE
ARM: pxa: remove incorrect __init annotation on pxa27x_set_pwrmode
ARM: pxa: raumfeld: make some variables static
ARM: OMAP: Change all cpu_is_* occurences to soc_is_* for id.c
ARM: OMAP2+: Rename cpu_is macros to soc_is
arm: omap2: timer: limit hwmod usage to non-DT boots
arm: omap2+: select 32k clocksource driver
clocksource: add TI 32.768 Hz counter driver
arm: omap2: timer: rename omap_sync32k_timer_init()
arm: omap2: timer: always call clocksource_of_init() when DT
arm: omap2: timer: move realtime_counter_init() around
...
projects / linux-beck.git / log