Florian Fainelli [Mon, 13 Feb 2012 01:23:20 +0000 (01:23 +0000)]
cpmac: fix PHY name to match MDIO bus name
Commit d1733f07: cpmac: use an unique MDIO bus name changed the MDIO bus
name from "1" to "cpmac-1", this breaks the PHY connection logic because
the PHY name still uses the old bus names "0" and "1", fix that to
always use the mdio bus id instead.
Signed-off-by: Florian Fainelli <florian@openwrt.org> Signed-off-by: David S. Miller <davem@davemloft.net>
ARM: at91: drop ide driver in favor of the pata one
Driver at91_ide is broken and should not be fixed: remove it.
Modification of device files that where making use of it. The
PATA driver (pata_at91) is able to replace at91_ide.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Since 3.2 kernel, the driver starts trying to assign the multi-io DACs
before the speaker, thus it assigns DAC2/3 for multi-io and DAC4 for
the speaker for a standard laptop setup like a HP, a speaker, a mic-in
and a line-in. However, on Acer Aspire 6935, it seems that the
speaker pin 0x14 must be connected with either DAC1 or 2; otherwise it
results in silence by some reason, although the codec itself allows
the routing to DAC3/4.
As a workaround, the connection list of each pin is reduced to be
mapped to either only DAC1/2 or DAC3/4, so that the compatible
assignment as in kernel 3.1 is achieved.
Takashi Iwai [Mon, 13 Feb 2012 14:04:06 +0000 (15:04 +0100)]
ALSA: hda - Fix initialization of secondary capture source on VT1705
VT1705 codec has two ADCs where the secondary ADC has no MUX but only
a fixed connection to the mic pin. This confused the driver and it
tries always overriding the input-source selection by assumption of
the existing MUX for the secondary ADC, resulted in resetting the
input-source at each time PM (including power-saving) occurs.
The fix is simply to check the existence of MUX for secondary ADCs in
the initialization code.
It's useful to print the error code when a called function fails so a
diagnosis of why it failed is possible. In this case, it fails because
we try to register some data for the wl12xx driver, but as the driver
is not configured, a stub function is used which simply returns -ENOSYS.
Let's do the simple thing for -rc and print the error code.
Also, the return code from platform_register_device() at each of these
sites was not being checked. Add some checking, and again print the
error code.
This should be fixed properly for the next merge window so we don't
issue error messages merely because a driver is not configured.
Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Tue, 7 Feb 2012 10:51:39 +0000 (10:51 +0000)]
ARM: omap: fix section mismatch warnings in mux.c caused by hsmmc.c
The previous commit causes new section mismatch warnings:
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdb30): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_gpio()
The function omap_init_hsmmc() references
the function __init omap_mux_init_gpio().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_gpio is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdb4c): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_gpio()
The function omap_init_hsmmc() references
the function __init omap_mux_init_gpio().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_gpio is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdb60): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_signal()
The function omap_init_hsmmc() references
the function __init omap_mux_init_signal().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdb6c): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_signal()
The function omap_init_hsmmc() references
the function __init omap_mux_init_signal().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdb78): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_signal()
The function omap_init_hsmmc() references
the function __init omap_mux_init_signal().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdb90): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_signal()
The function omap_init_hsmmc() references
the function __init omap_mux_init_signal().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdb9c): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_signal()
The function omap_init_hsmmc() references
the function __init omap_mux_init_signal().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdba8): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_signal()
The function omap_init_hsmmc() references
the function __init omap_mux_init_signal().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdbc0): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_signal()
The function omap_init_hsmmc() references
the function __init omap_mux_init_signal().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdbcc): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_signal()
The function omap_init_hsmmc() references
the function __init omap_mux_init_signal().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdbd8): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_signal()
The function omap_init_hsmmc() references
the function __init omap_mux_init_signal().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdbf8): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_signal()
The function omap_init_hsmmc() references
the function __init omap_mux_init_signal().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdc04): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_signal()
The function omap_init_hsmmc() references
the function __init omap_mux_init_signal().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdc10): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_signal()
The function omap_init_hsmmc() references
the function __init omap_mux_init_signal().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdc28): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_signal()
The function omap_init_hsmmc() references
the function __init omap_mux_init_signal().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdc34): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_signal()
The function omap_init_hsmmc() references
the function __init omap_mux_init_signal().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdc40): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_signal()
The function omap_init_hsmmc() references
the function __init omap_mux_init_signal().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdc58): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_signal()
The function omap_init_hsmmc() references
the function __init omap_mux_init_signal().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdc64): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_signal()
The function omap_init_hsmmc() references
the function __init omap_mux_init_signal().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdc70): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_signal()
The function omap_init_hsmmc() references
the function __init omap_mux_init_signal().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdc7c): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_signal()
The function omap_init_hsmmc() references
the function __init omap_mux_init_signal().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
Again, as for omap2_hsmmc_init(), these functions are callable at
runtime via the gpio-twl4030.c driver, and so these can't be marked
__init.
Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Tue, 7 Feb 2012 10:45:50 +0000 (10:45 +0000)]
ARM: omap: fix section mismatch warning for sdp3430_twl_gpio_setup()
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xd0f0): Section mismatch in reference from the function sdp3430_twl_gpio_setup() to the function .init.text:omap2_hsmmc_init()
The function sdp3430_twl_gpio_setup() references
the function __init omap2_hsmmc_init().
This is often because sdp3430_twl_gpio_setup lacks a __init
annotation or the annotation of omap2_hsmmc_init is wrong.
sdp3430_twl_gpio_setup() is called via platform data from the
gpio-twl4030 module, which can be inserted and removed at runtime.
This makes sdp3430_twl_gpio_setup() callable at runtime, and prevents
it being marked with an __init annotation.
As it calls omap2_hsmmc_init() unconditionally, the only resolution to
this warning is to remove the __init markings from omap2_hsmmc_init()
and its called functions. This addresses the functions in hsmmc.c.
Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Tue, 7 Feb 2012 10:41:34 +0000 (10:41 +0000)]
ARM: omap: fix section mismatch error for omap_4430sdp_display_init()
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xb798): Section mismatch in reference from the function omap_4430sdp_display_init() to the function .init.text:omap_display_init()
The function omap_4430sdp_display_init() references
the function __init omap_display_init().
This is often because omap_4430sdp_display_init lacks a __init
annotation or the annotation of omap_display_init is wrong.
Fix this by adding __init to omap_4430sdp_display_init().
Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Tue, 7 Feb 2012 10:34:01 +0000 (10:34 +0000)]
ARM: omap: fix section mismatch warning for omap_secondary_startup()
WARNING: vmlinux.o(.text+0x1c664): Section mismatch in reference from the function omap_secondary_startup() to the function .cpuinit.text:secondary_startup()
The function omap_secondary_startup() references
the function __cpuinit secondary_startup().
This is often because omap_secondary_startup lacks a __cpuinit
annotation or the annotation of secondary_startup is wrong.
Unfortunately, fixing this causes a new warning which is harder to
solve:
WARNING: arch/arm/mach-omap2/built-in.o(.text+0x5328): Section mismatch in reference from the function omap4_hotplug_cpu() to the function .cpuinit.text:omap_secondary_startup()
The function omap4_hotplug_cpu() references
the function __cpuinit omap_secondary_startup().
This is often because omap4_hotplug_cpu lacks a __cpuinit
annotation or the annotation of omap_secondary_startup is wrong.
because omap4_hotplug_cpu() is used by power management code as well,
which may not end up using omap_secondary_startup().
Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Tue, 7 Feb 2012 11:07:24 +0000 (11:07 +0000)]
ARM: omap: preemptively fix section mismatch in omap4_sdp4430_wifi_mux_init()
Found by review.
omap4_sdp4430_wifi_mux_init() is called by an __init marked function,
and only calls omap_mux_init_gpio() and omap_mux_init_signal() which
are both also an __init marked functions.
The only reason this doesn't issue a warning is because the compiler
inlines omap4_sdp4430_wifi_mux_init() into omap4_sdp4430_wifi_init().
So, lets add the __init annotation to ensure this remains safe should
the compiler choose not to inline.
Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Tue, 7 Feb 2012 10:18:34 +0000 (10:18 +0000)]
ARM: omap: fix section mismatch warning in mux.c
WARNING: arch/arm/mach-omap2/built-in.o(.text+0x15a4): Section mismatch in reference from the function omap_mux_init_signals() to the function .init.text:omap_mux_init_signal()
The function omap_mux_init_signals() references
the function __init omap_mux_init_signal().
This is often because omap_mux_init_signals lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Tue, 7 Feb 2012 10:00:34 +0000 (10:00 +0000)]
ARM: omap: fix section mismatch errors in TWL PMIC driver
WARNING: drivers/mfd/built-in.o(.devinit.text+0x258): Section mismatch in reference from the function twl_probe() to the function .init.text:twl4030_power_init()
The function __devinit twl_probe() references
a function __init twl4030_power_init().
If twl4030_power_init is only used by twl_probe then
annotate twl4030_power_init with a matching annotation.
twl4030_power_init() references other __init marked functions, so
these too must become __devinit.
Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On my OMAP4 platform, I'm getting this error message repeated several
times at boot:
omap_vc_i2c_init: I2C config for all channels must match.
omap_vc_i2c_init: I2C config for all channels must match.
This doesn't help identify what the problem is. Fix this message to
be more informative:
omap_vc_i2c_init: I2C config for vdd_iva does not match other channels (0).
omap_vc_i2c_init: I2C config for vdd_mpu does not match other channels (0).
This allows us to identify which voltage domains have a problem, and
what the I2C configuration state (a boolean, i2c_high_speed) setting
being used actually is.
From this we find that omap4_core_pmic has i2c_high_speed false, but
omap4_iva_pmic and omap4_mpu_pmic both have it set true.
Acked-by: Tony Lindgren <tony@atomide.com> Acked-by: Kevin Hilman <khilman@ti.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Tue, 7 Feb 2012 10:13:02 +0000 (10:13 +0000)]
ARM: omap: fix vc.c PMIC error message
While testing on my OMAP3430 platform, this error message was emitted:
omap_vc_init_channel: PMIC info requried to configure vc forvdd_core not populated.Hence cannot initialize vc
Trying to find this message was difficult because it was wrapped across
several lines. It also mis-spells "required", doesn't read very well,
and has spaces lacking. Let's replace it with a more concise:
omap_vc_init_channel: No PMIC info for vdd_core
While we're here, fix a simple spelling error in a comment.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The vision_ep9307 machine uses the ep93xx build-in gpios and needs to
include <mach/gpio-ep93xx.h> to pickup the defines.
The gpio_to_irq() call is now a callback to the gpio-ep93xx.c driver
and cannot be used as a constant initializer for the .irq member of
struct i2c_board_info.
Signed-off-by: Hartley Sweeten <hsweeten@visionengravers.com> Acked-by: Ryan Mallon <rmallon@gmail.com> Acked-by: Mika Westerberg <mika.westerberg@iki.fi> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Neal Cardwell [Sun, 12 Feb 2012 18:37:10 +0000 (18:37 +0000)]
tcp: fix range tcp_shifted_skb() passes to tcp_sacktag_one()
Fix the newly-SACKed range to be the range of newly-shifted bytes.
Previously - since 832d11c5cd076abc0aa1eaf7be96c81d1a59ce41 -
tcp_shifted_skb() incorrectly called tcp_sacktag_one() with the start
and end sequence numbers of the skb it passes in set to the range just
beyond the range that is newly-SACKed.
This commit also removes a special-case adjustment to lost_cnt_hint in
tcp_shifted_skb() since the pre-existing adjustment of lost_cnt_hint
in tcp_sacktag_one() now properly handles this things now that the
correct start sequence number is passed in.
Signed-off-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Neal Cardwell [Sun, 12 Feb 2012 18:37:09 +0000 (18:37 +0000)]
tcp: allow tcp_sacktag_one() to tag ranges not aligned with skbs
This commit allows callers of tcp_sacktag_one() to pass in sequence
ranges that do not align with skb boundaries, as tcp_shifted_skb()
needs to do in an upcoming fix in this patch series.
In fact, now tcp_sacktag_one() does not need to depend on an input skb
at all, which makes its semantics and dependencies more clear.
Signed-off-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Mon, 13 Feb 2012 05:50:07 +0000 (05:50 +0000)]
Merge branch 'v3.3-samsung-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes
* 'v3.3-samsung-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung: (2 commits)
ARM: EXYNOS: Add cpu-offset property in gic device tree node
ARM: EXYNOS: Bring exynos4-dt up to date
Linux 3.3-rc3
This includes an update to the v3.3-rc3 release from v3.3-rc2
It is because eSDHC controller has different bit setting for PROCTL
register at 0x28 comparing SD specification.
This patch sets DMAS bits correctly for byte operation and does not
change the default value of other field of PROCTL register.
For other FSL chips, such as MPC8536/P2020, PROCTL[DMAS]
bits are reserved and even if they are set to wrong bits, it will not
take effective.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com> Acked-by: Anton Vorontsov <cbouatmailru@gmail.com> Signed-off-by: Chris Ball <cjb@laptop.org>
Linus Torvalds [Sat, 11 Feb 2012 18:07:11 +0000 (10:07 -0800)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-block
Says Jens:
"Time to push off some of the pending items. I really wanted to wait
until we had the regression nailed, but alas it's not quite there yet.
But I'm very confident that it's "just" a missing expire on exit, so
fix from Tejun should be fairly trivial. I'm headed out for a week on
the slopes.
- Killing the barrier part of mtip32xx. It doesn't really support
barriers, and it doesn't need them (writes are fully ordered).
- A few fixes from Dan Carpenter, preventing overflows of integer
multiplication.
- A fixup for loop, fixing a previous commit that didn't quite solve
the partial read problem from Dave Young.
- A bio integer overflow fix from Kent Overstreet.
- Improvement/fix of the door "keep locked" part of the cdrom shared
code from Paolo Benzini.
- A few cfq fixes from Shaohua Li.
- A fix for bsg sysfs warning when removing a file it did not create
from Stanislaw Gruszka.
- Two fixes for floppy from Vivek, preventing a crash.
- A few block core fixes from Tejun. One killing the over-optimized
ioc exit path, cleaning that up nicely. Two others fixing an oops
on elevator switch, due to calling into the scheduler merge check
code without holding the queue lock."
* 'for-linus' of git://git.kernel.dk/linux-block:
block: fix lockdep warning on io_context release put_io_context()
relay: prevent integer overflow in relay_open()
loop: zero fill bio instead of return -EIO for partial read
bio: don't overflow in bio_get_nr_vecs()
floppy: Fix a crash during rmmod
floppy: Cleanup disk->queue before caling put_disk() if add_disk() was never called
cdrom: move shared static to cdrom_device_info
bsg: fix sysfs link remove warning
block: don't call elevator callbacks for plug merges
block: separate out blk_rq_merge_ok() and blk_try_merge() from elevator functions
mtip32xx: removed the irrelevant argument of mtip_hw_submit_io() and the unused member of struct driver_data
block: strip out locking optimization in put_io_context()
cdrom: use copy_to_user() without the underscores
block: fix ioc locking warning
block: fix NULL icq_cache reference
block,cfq: change code order
Tejun Heo [Sat, 11 Feb 2012 11:37:25 +0000 (12:37 +0100)]
block: fix lockdep warning on io_context release put_io_context()
11a3122f6c "block: strip out locking optimization in put_io_context()"
removed ioc_lock depth lockdep annoation along with locking
optimization; however, while recursing from put_io_context() is no
longer possible, ioc_release_fn() may still end up putting the last
reference of another ioc through elevator, which wlil grab ioc->lock
triggering spurious (as the ioc is always different one) A-A deadlock
warning.
As this can only happen one time from ioc_release_fn(), using non-zero
subclass from ioc_release_fn() is enough. Use subclass 1.
1) GRO MAC header comparisons were ethernet specific, breaking other
link types. This required a multi-faceted fix to cure the originally
noted case (Infiniband), because IPoIB was lying about it's actual
hard header length. Thanks to Eric Dumazet, Roland Dreier, and
others.
2) Fix build failure when INET_UDP_DIAG is built in and ipv6 is modular.
From Anisse Astier.
3) Off by ones and other bug fixes in netprio_cgroup from Neil Horman.
4) ipv4 TCP reset generation needs to respect any network interface
binding from the socket, otherwise route lookups might give a
different result than all the other segments received. From Shawn
Lu.
5) Fix unintended regression in ipv4 proxy ARP responses, from Thomas
Graf.
6) Fix SKB under-allocation bug in sh_eth, from Yoshihiro Shimoda.
7) Revert skge PCI mapping changes that are causing crashes for some
folks, from Stephen Hemminger.
8) IPV4 route lookups fill in the wildcarded fields of the given flow
lookup key passed in, which is fine most of the time as this is
exactly what the caller's want. However there are a few cases that
want to retain the original flow key values afterwards, so handle
those cases properly. Fix from Julian Anastasov.
9) IGB/IXGBE VF lookup bug fixes from Greg Rose.
10) Properly null terminate filename passed to ethtool flash device
method, from Ben Hutchings.
11) S3 resume fix in via-velocity from David Lv.
12) Fix double SKB free during xmit failure in CAIF, from Dmitry
Tarnyagin.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (72 commits)
net: Don't proxy arp respond if iif == rt->dst.dev if private VLAN is disabled
ipv4: Fix wrong order of ip_rt_get_source() and update iph->daddr.
netprio_cgroup: fix wrong memory access when NETPRIO_CGROUP=m
netprio_cgroup: don't allocate prio table when a device is registered
netprio_cgroup: fix an off-by-one bug
bna: fix error handling of bnad_get_flash_partition_by_offset()
isdn: type bug in isdn_net_header()
net: Make qdisc_skb_cb upper size bound explicit.
ixgbe: ethtool: stats user buffer overrun
ixgbe: dcb: up2tc mapping lost on disable/enable CEE DCB state
ixgbe: do not update real num queues when netdev is going away
ixgbe: Fix broken dependency on MAX_SKB_FRAGS being related to page size
ixgbe: Fix case of Tx Hang in PF with 32 VFs
ixgbe: fix vf lookup
igb: fix vf lookup
e1000: add dropped DMA receive enable back in for WoL
gro: more generic L2 header check
IPoIB: Stop lying about hard_header_len and use skb->cb to stash LL addresses
zd1211rw: firmware needs duration_id set to zero for non-pspoll frames
net: enable TC35815 for MIPS again
...
Yinghai Lu [Sun, 5 Feb 2012 06:55:00 +0000 (22:55 -0800)]
PCI: Fix pci cardbus removal
During test busn_res allocation with cardbus, found pci card removal is not
working anymore, and it turns out it is broken by:
|commit 79cc9601c3e42b4f0650fe7e69132ebce7ab48f9
|Date: Tue Nov 22 21:06:53 2011 -0800
|
| PCI: Only call pci_stop_bus_device() one time for child devices at remove
The above changed the behavior of pci_remove_behind_bridge that
yenta_cardbus depended on. So restore the old behavoir of
pci_remove_behind_bridge (which requires stopping and removing of all
devices) by:
1. rename pci_remove_behind_bridge to __pci_remove_behind_bridge, and let
__pci_remove_bus_device() call it instead.
2. add pci_stop_behind_bridge that will stop devices behind a bridge
3. add back pci_remove_behind_bridge that will stop and remove devices
under bridge.
Thomas Graf [Fri, 10 Feb 2012 04:07:11 +0000 (04:07 +0000)]
net: Don't proxy arp respond if iif == rt->dst.dev if private VLAN is disabled
Commit 653241 (net: RFC3069, private VLAN proxy arp support) changed
the behavior of arp proxy to send arp replies back out on the interface
the request came in even if the private VLAN feature is disabled.
Previously we checked rt->dst.dev != skb->dev for in scenarios, when
proxy arp is enabled on for the netdevice and also when individual proxy
neighbour entries have been added.
This patch adds the check back for the pneigh_lookup() scenario.
Signed-off-by: Thomas Graf <tgraf@suug.ch> Acked-by: Jesper Dangaard Brouer <hawk@comx.dk> Signed-off-by: David S. Miller <davem@davemloft.net>
Li Wei [Thu, 9 Feb 2012 21:15:25 +0000 (21:15 +0000)]
ipv4: Fix wrong order of ip_rt_get_source() and update iph->daddr.
This patch fix a bug which introduced by commit ac8a4810 (ipv4: Save
nexthop address of LSRR/SSRR option to IPCB.).In that patch, we saved
the nexthop of SRR in ip_option->nexthop and update iph->daddr until
we get to ip_forward_options(), but we need to update it before
ip_rt_get_source(), otherwise we may get a wrong src.
Signed-off-by: Li Wei <lw@cn.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Neil Horman [Fri, 10 Feb 2012 05:43:38 +0000 (05:43 +0000)]
netprio_cgroup: fix wrong memory access when NETPRIO_CGROUP=m
When the netprio_cgroup module is not loaded, net_prio_subsys_id
is -1, and so sock_update_prioidx() accesses cgroup_subsys array
with negative index subsys[-1].
Make the code resembles cls_cgroup code, which is bug free.
Origionally-authored-by: Li Zefan <lizf@cn.fujitsu.com> Signed-off-by: Li Zefan <lizf@cn.fujitsu.com> Signed-off-by: Neil Horman <nhorman@tuxdriver.com> CC: "David S. Miller" <davem@davemloft.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Neil Horman [Fri, 10 Feb 2012 05:43:37 +0000 (05:43 +0000)]
netprio_cgroup: don't allocate prio table when a device is registered
So we delay the allocation till the priority is set through cgroup,
and this makes skb_update_priority() faster when it's not set.
This also eliminates an off-by-one bug similar with the one fixed
in the previous patch.
Origionally-authored-by: Li Zefan <lizf@cn.fujitsu.com> Signed-off-by: Li Zefan <lizf@cn.fujitsu.com> Signed-off-by: Neil Horman <nhorman@tuxdriver.com> CC: "David S. Miller" <davem@davemloft.net> Signed-off-by: David S. Miller <davem@davemloft.net>
We got weired output, because we exceeded the boundary of the array.
We may even crash the kernel..
Origionally-authored-by: Li Zefan <lizf@cn.fujitsu.com> Signed-off-by: Li Zefan <lizf@cn.fujitsu.com> Signed-off-by: Neil Horman <nhorman@tuxdriver.com> CC: "David S. Miller" <davem@davemloft.net> Signed-off-by: David S. Miller <davem@davemloft.net>
PCI: set pci sriov page size before reading SRIOV BAR
For an SRIOV device, PCI_SRIOV_SYS_PGSIZE should be set before
the PCI_SRIOV_BAR are queried. The sys pagesize defaults to 4k,
so this change is required on powerpc box with 64k base page size.
This is a regression caused due to moving SRIOV init to sriov_enable().
| PCI: delay configuration of SRIOV capability
| The SRIOV capability, namely page size and total_vfs of a device are
| configured during enumeration phase of the device. This can potentially
| interfere with the PCI operations of the platform, if the IOV capability
| of the device is not enabled.
Yinghai Lu [Mon, 30 Jan 2012 11:25:24 +0000 (12:25 +0100)]
PCI: workaround hard-wired bus number V2
Fixes PCI device detection on IBM xSeries IBM 3850 M2 / x3950 M2
when using ACPI resources (_CRS).
This is default, a manual workaround (without this patch)
would be pci=nocrs boot param.
V2: Add dev_warn if the workaround is hit. This should reveal
how common such setups are (via google) and point to possible
problems if things are still not working as expected.
-> Suggested by Jan Beulich.
Stop reusing dquots from the freelist when allocating new ones directly, and
implement a shrinker that actually follows the specifications for the
interface. The shrinker implementation is still highly suboptimal at this
point, but we can gradually work on it.
This also fixes an bug in the previous lock ordering, where we would take
the hash and dqlist locks inside of the freelist lock against the normal
lock ordering. This is only solvable by introducing the dispose list,
and thus not when using direct reclaim of unused dquots for new allocations.
As a side-effect the quota upper bound and used to free ratio values in
/proc/fs/xfs/xqm are set to 0 as these values don't make any sense in the
new world order.
Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Ben Myers <bpm@sgi.com>
Linus Torvalds [Fri, 10 Feb 2012 17:06:25 +0000 (09:06 -0800)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/i915: fixup interlaced bits clearing in PIPECONF on PCH_SPLIT (v2)
drm/i915: no lvds quirk for AOpen MP45
drm/i915: Force explicit bpp selection for intel_dp_link_required
drm/radeon: do not continue after error from r600_ib_test
drivers/gpu/drm/drm_ioc32.c: initialize all fields
drm/i915: fixup interlaced bits clearing in PIPECONF on PCH_SPLIT
drm/i915:: Disable FBC on SandyBridge
Linus Torvalds [Fri, 10 Feb 2012 17:05:52 +0000 (09:05 -0800)]
Merge tag 'writeback-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/wfg/linux
fix 1 mysterious divide error
fix 3 NULL dereference bugs in writeback tracing, on SD card removal w/o umount
* tag 'writeback-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/wfg/linux:
writeback: fix dereferencing NULL bdi->dev on trace_writeback_queue
lib: proportion: lower PROP_MAX_SHIFT to 32 on 64-bit kernel
writeback: fix NULL bdi->dev in trace writeback_single_inode
backing-dev: fix wakeup timer races with bdi_unregister()
Linus Torvalds [Fri, 10 Feb 2012 17:05:07 +0000 (09:05 -0800)]
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf: Fix double start/stop in x86_pmu_start()
perf evsel: Fix an issue where perf report fails to show the proper percentage
perf tools: Fix prefix matching for kernel maps
perf tools: Fix perf stack to non executable on x86_64
perf: Remove deprecated WARN_ON_ONCE()
Linus Torvalds [Fri, 10 Feb 2012 17:04:37 +0000 (09:04 -0800)]
Merge tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Couple of regressions, couple of zero-day bugs, a minor enhancement.
Nothing really major.
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (f75375s) Let f75375_update_device treat pwmX as a measured value
hwmon: (f75375s) Fix bit shifting in f75375_write16
hwmon: (f75375s) Fix reading of wrong register when initializing the F75387
hwmon: (f75375s) Fix automatic pwm mode setting for F75373 & F75375
hwmon: (w83627ehf) Remove duplicate code
Dave Airlie [Fri, 10 Feb 2012 08:35:19 +0000 (08:35 +0000)]
Merge branch 'drm-intel-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/keithp/linux into drm-fixes
* 'drm-intel-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/keithp/linux:
drm/i915: fixup interlaced bits clearing in PIPECONF on PCH_SPLIT (v2)
drm/i915: no lvds quirk for AOpen MP45
drm/i915: Force explicit bpp selection for intel_dp_link_required
drm/i915: fixup interlaced bits clearing in PIPECONF on PCH_SPLIT
drm/i915:: Disable FBC on SandyBridge
Paul Walmsley [Fri, 10 Feb 2012 01:24:03 +0000 (18:24 -0700)]
ARM: OMAP2xxx: PM: fix OMAP2xxx-specific UART idle bug in v3.3
On OMAP2420-based systems, the PM code ignores the state of the UART
functional clocks when determining what idle state to enter. This
breaks the serial port now that the UART driver's clock behavior can
be controlled via the PM autosuspend timeout.
To fix, remove the special-case idle handling for the UARTs in the
OMAP2420/2430 PM idle code added by commit 4af4016c53f52b26461b8030211f8427a58fa5ed ("OMAP3: PM: UART: disable
clocks when idle and off-mode support").
Tested on Nokia N800. This patch is a collaboration between Tony
Lindgren <tony@atomide.com> and Paul Walmsley <paul@pwsan.com>.
Signed-off-by: Paul Walmsley <paul@pwsan.com> Acked-by: Kevin Hilman <khilman@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Andrew Lunn [Wed, 8 Feb 2012 14:52:47 +0000 (15:52 +0100)]
ARM: orion: Fix USB phy for orion5x.
The patch "ARM: orion: Consolidate USB platform setup code.", commit 4fcd3f374a928081d391cd9a570afe3b2c692fdc broke USB on TS-7800 and
other orion5x boards, because the wrong type of PHY was being passed
to the EHCI driver in the platform data. Orion5x needs EHCI_PHY_ORION
and all the others want EHCI_PHY_NA.
Allow the mach- code to tell the generic plat-orion code which USB PHY
enum to place into the platform data.
Version 2: Rebase to v3.3-rc2.
Reported-by: Ambroz Bizjak <ambrop7@gmail.com> Signed-off-by: Andrew Lunn <andrew@lunn.ch> Tested-by: Ambroz Bizjak <ambrop7@gmail.com> Acked-by: Nicolas Pitre <nico@linaro.org> Signed-off-by: Olof Johansson <olof@lixom.net>
Andrew Lunn [Wed, 8 Feb 2012 14:52:07 +0000 (15:52 +0100)]
ARM: orion: Fix Orion5x GPIO regression from MPP cleanup
Patchset "ARM: orion: Refactor the MPP code common in the orion
platform" broke at least Orion5x based platforms. These platforms have
pins configured as GPIO when the selector is not 0x0. However the
common code assumes the selector is always 0x0 for a GPIO lines. It
then ignores the GPIO bits in the MPP definitions, resulting in that
Orion5x machines cannot correctly configure there GPIO lines.
The Fix removes the assumption that the selector is always 0x0.
In order that none GPIO configurations are correctly blocked,
Kirkwood and mv78xx0 MPP definitions are corrected to only set the
GPIO bits for GPIO configurations.
This third version, which does not contain any whitespace changes,
and is rebased on v3.3-rc2.
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Acked-by: Nicolas Pitre <nico@linaro.org> Signed-off-by: Olof Johansson <olof@lixom.net>
Since mc13xxx-regulator-core.c and the actual drivers can get built
into seperate modules, you have to export the DT support symbols
"mc13xxx_get_num_regulators_dt" and "mc13xxx_parse_regulators_dt"
otherwise the allmodconfig build fails on sparc64.
[Updated the subject; the same thing was previously reported and fixed
in -next but for some reason nobody noticed for some considerable time
after the issue was introduced -- broonie]
Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Linus Torvalds [Thu, 9 Feb 2012 21:52:57 +0000 (13:52 -0800)]
Merge tag 'tty-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Serial/TTY fixes for the 3.3-rc3 tree
Just a few new device ids, omap serial driver regression fixes, and a
build fix for the 8250 driver movement.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* tag 'tty-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: serial: omap-serial: wakeup latency constraint is in microseconds, not milliseconds
tty: serial: OMAP: block idle while the UART is transferring data in PIO mode
tty: serial: OMAP: use a 1-byte RX FIFO threshold in PIO mode
m32r: relocate drivers back out of 8250 dir
tty: fix a build failure on sparc
serial: samsung: Add support for EXYNOS5250
serial: samsung: Add support for EXYNOS4212 and EXYNOS4412
drivers/tty/vt/vt_ioctl.c: fix KDFONTOP 32bit compatibility layer
Linus Torvalds [Thu, 9 Feb 2012 21:52:18 +0000 (13:52 -0800)]
Merge tag 'staging-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Staging tree patches for 3.3-rc3
Big things here is the deletion of the Android pmem driver, as it's
obsolete and no one uses it, the gma500 driver as it's already in the
drm portion of the kernel tree, and the pohmelfs filesystem as it's
obsolete and a rewritten version is being proposed for the fs/ section
of the kernel.
Other than that, a smattering of different bugfixes and regressions, and
some omap drm api merge fixups that were needed due to api changes in
the main portion of the drm tree, allowing this code to build properly
again.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* tag 'staging-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (28 commits)
staging: pohmelfs: remove drivers/staging/pohmelfs
staging: android/ram_console: Don't build on arches w/o ioremap
staging: r8712u: Use asynchronous firmware loading
staging: usbip: fix to prevent potentially using uninitialized spinlock
staging: r8712u: Fix problem when CONFIG_R8712_AP is set
staging: tidspbridge: fix incorrect free to drv_datap
staging: tidspbridge: fix bridge_open memory leaks
staging: android: lowmemorykiller: Don't wait more than one second for a process to die
MAINTAINERS: staging: iio: add iio information
staging: zcache: fix serialization bug in zv stats
staging: fix go7007-usb license
Staging: android: binder: Fix crashes when sharing a binder file between processes
Staging: android: Remove pmem driver
Staging: asus_oled: fix NULL-ptr crash on unloading
Staging: asus_oled: fix image processing
Staging: android: binder: Don't call dump_stack in binder_vma_open
staging: r8712u: Add new Sitecom UsB ID
zcache: Set SWIZ_BITS to 8 to reduce tmem bucket lock contention.
zcache: fix deadlock condition
staging: drm/omap: fix locking issue
...
Linus Torvalds [Thu, 9 Feb 2012 21:51:36 +0000 (13:51 -0800)]
Merge tag 'driver-core-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Driver core fixes for the 3.3-rc3 tree.
A few fixes for kobject warnings that have popped up in the cpu hotplug path,
and a regression fix for the speed of the hotplug memory code.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* tag 'driver-core-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
driver-core: cpu: fix kobject warning when hotplugging a cpu
ACPI: remove duplicated lines of merging problems with acpi_processor_add
docbook: fix fatal errors in device-drivers docbook and add DMA Management section
drivers/base/memory.c: fix memory_dev_init() long delay
driver core: cpu: remove kernel warning when removing a cpu
Linus Torvalds [Thu, 9 Feb 2012 21:51:13 +0000 (13:51 -0800)]
Merge tag 'char-misc-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Minor char-misc fixes for 3.3-rc3
Nothing big here, some Kconfig fixes for the MISC_DEVICES config option
that was being used incorrectly, and some other minor bug fixes.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* tag 'char-misc-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
mmc: cb710 core: Add missing spin_lock_init for irq_lock of struct cb710_chip
cs5535-mfgpt: don't call __init function from __devinit
vmw_balloon: fix for a -Wuninitialized warning
drivers: misc: Remove MISC_DEVICES config option
c2port: fix build error for duramar2150 due to missing header.
Linus Torvalds [Thu, 9 Feb 2012 21:50:54 +0000 (13:50 -0800)]
Merge tag 'usb-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
USB fixes for 3.3-rc3
Here are a few minor USB fixes and a bunch of device id updates for the
USB drivers.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* tag 'usb-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: usbserial: add new PID number (0xa951) to the ftdi driver
usb: ch9.h: usb_endpoint_maxp() uses __le16_to_cpu()
usb: musb: fix a build error on mips
uwb & wusb & usb wireless controllers: fix kconfig error & build errors
usb: Skip PCI USB quirk handling for Netlogic XLP
powerpc/usb: fix issue of CPU halt when missing USB PHY clock
usb: otg: mv_otg: Add dependence
usb: host: Distinguish Kconfig text for Freescale controllers
USB: add new zte 3g-dongle's pid to option.c
usb: ch9.h: usb_endpoint_maxp() uses __le16_to_cpu()
USB: qcserial: don't enable autosuspend
USB: qcserial: add several new serial devices
usb: otg: mv_otg: Add dependence
usb: gadget: zero: fix bug in loopback autoresume handling
Dan Carpenter [Thu, 9 Feb 2012 00:49:34 +0000 (00:49 +0000)]
bna: fix error handling of bnad_get_flash_partition_by_offset()
The current error handling doesn't work because we flash_part is a u32
so the checks for negative error codes don't work. I considered making
things signed but I don't know the hardware enough to say if that's a
problem. Really, we don't use the error codes so just returning zero
for all problems is fine.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Thu, 9 Feb 2012 00:46:47 +0000 (00:46 +0000)]
isdn: type bug in isdn_net_header()
We use len to store the return value from eth_header(). eth_header()
can return -ETH_HLEN (-14). We want to pass this back instead of
truncating it to 65522 and returning that.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Simon Graham [Thu, 9 Feb 2012 14:55:13 +0000 (09:55 -0500)]
rtlwifi: Modify rtl_pci_init to return 0 on success
Fixes problem where caller would think routine succeeded when it failed
leading to divide by zero panic.
Signed-off-by: Simon Graham <simon.graham@virtualcomputer.com> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
read_lock(&tpt_trig->trig.leddev_list_lock) is accessed via the path
ieee80211_open (->) ieee80211_do_open (->) ieee80211_mod_tpt_led_trig
(->) ieee80211_start_tpt_led_trig (->) tpt_trig_timer before initializing
it.
the intilization of this read/write lock happens via the path
ieee80211_led_init (->) led_trigger_register, but we are doing
'ieee80211_led_init' after 'ieeee80211_if_add' where we
register netdev_ops.
so we access leddev_list_lock before initializing it and causes the
following bug in chrome laptops with AR928X cards with the following
script
while true
do
sudo modprobe -v ath9k
sleep 3
sudo modprobe -r ath9k
sleep 3
done
BUG: rwlock bad magic on CPU#1, wpa_supplicant/358, f5b9eccc
Pid: 358, comm: wpa_supplicant Not tainted 3.0.13 #1
Call Trace:
David S. Miller [Mon, 6 Feb 2012 20:14:37 +0000 (15:14 -0500)]
net: Make qdisc_skb_cb upper size bound explicit.
Just like skb->cb[], so that qdisc_skb_cb can be encapsulated inside
of other data structures.
This is intended to be used by IPoIB so that it can remember
addressing information stored at hard_header_ops->create() time that
it can fetch when the packet gets to the transmit routine.
Signed-off-by: David S. Miller <davem@davemloft.net>
Paul Walmsley [Thu, 26 Jan 2012 02:50:56 +0000 (19:50 -0700)]
tty: serial: omap-serial: wakeup latency constraint is in microseconds, not milliseconds
The receive FIFO wakeup latency estimate in the omap-serial driver is
three orders of magnitude too small. This effectively prevents the
MPU from going to a low-power state when CONFIG_CPU_IDLE=y. This is a
major power management regression and masks some other FIFO-related
bugs in the driver.
Fix by correcting the most egregious problem in the RX wakeup latency
estimate. There are several other flaws in the estimator; these will
be fixed by a separate patch series intended for 3.4.
The difference in low-power states with this patch can be observed via
debugfs in pm_debug/count.
This estimate does not have any effect when CONFIG_CPU_IDLE=n.
Signed-off-by: Paul Walmsley <paul@pwsan.com> Cc: Tomi Valkeinen <tomi.valkeinen@ti.com> Cc: Alan Cox <alan@linux.intel.com> Acked-by: Govindraj.R <govindraj.raja@ti.com> Reviewed-by: Kevin Hilman <khilman@ti.com> Tested-by: Kevin Hilman <khilman@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Paul Walmsley [Thu, 26 Jan 2012 02:50:52 +0000 (19:50 -0700)]
tty: serial: OMAP: block idle while the UART is transferring data in PIO mode
Prevent OMAP UARTs from going idle while they are still transferring
data in PIO mode. This works around an oversight in the OMAP UART
hardware present in OMAP34xx and earlier: an idle UART won't send a
wakeup when the TX FIFO threshold is reached. This causes long delays
during data transmission when the MPU powerdomain enters a low-power
mode. The MPU interrupt controller is not able to respond to
interrupts when it's in a low-power state, so the TX buffer is not
refilled until another wakeup event occurs.
This fix changes the erratum i291 DMA idle workaround. Rather than
toggling between force-idle and no-idle, it will toggle between
smart-idle and no-idle. The important part of the workaround is the
no-idle part, so this shouldn't result in any change in behavior.
This fix should work on all OMAP UARTs. Future patches intended for
the 3.4 merge window will make this workaround conditional on a
"feature" flag, and will use the OMAP36xx+ TX event wakeup support.
Thanks to Kevin Hilman <khilman@ti.com> for mentioning the erratum i291
workaround, which led to the development of this approach.
Signed-off-by: Paul Walmsley <paul@pwsan.com> Cc: Alan Cox <alan@linux.intel.com> Cc: Tomi Valkeinen <tomi.valkeinen@ti.com> Acked-by: Govindraj.R <govindraj.raja@ti.com> Reviewed-by: Kevin Hilman <khilman@ti.com> Tested-by: Kevin Hilman <khilman@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Paul Walmsley [Thu, 26 Jan 2012 02:50:36 +0000 (19:50 -0700)]
tty: serial: OMAP: use a 1-byte RX FIFO threshold in PIO mode
In the (default) PIO mode, use a one-byte RX FIFO threshold. The OMAP
UART IP blocks do not appear to be capable of waking the system under
an RX timeout condition. Since the previous RX FIFO threshold was 16
bytes, this meant that omap-serial.c did not become aware of any
received data until all those bytes arrived or until another UART
interrupt occurred. This made the serial console and presumably other
serial applications (GPS, serial Bluetooth) unusable or extremely
slow. A 1-byte RX FIFO threshold also allows the MPU to enter a
low-power consumption state while waiting for the FIFO to fill.
This can be verified using the serial console by comparing the
behavior when "0123456789abcde" is pasted in from another window, with
the behavior when "0123456789abcdef" is pasted in. Since the former
string is less than sixteen bytes long, the string is not echoed for
some time, while the latter string is echoed immediately.
DMA operation is unaffected by this patch.
Thanks to Russell King - ARM Linux <linux@arm.linux.org.uk> for some
additional information on the standard behavior of the RX timeout
event, which was used to improve this commit description.
Signed-off-by: Paul Walmsley <paul@pwsan.com> Cc: Tomi Valkeinen <tomi.valkeinen@ti.com> Cc: Govindraj Raja <govindraj.r@ti.com> Cc: Alan Cox <alan@linux.intel.com> Cc: Russell King <linux@arm.linux.org.uk> Reviewed-by: Kevin Hilman <khilman@ti.com> Tested-by: Kevin Hilman <khilman@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
David Howells [Thu, 9 Feb 2012 15:48:20 +0000 (15:48 +0000)]
Reduce the number of expensive division instructions done by _parse_integer()
_parse_integer() does one or two division instructions (which are slow)
per digit parsed to perform the overflow check.
Furthermore, these are particularly expensive examples of division
instruction as the number of clock cycles required to complete them may
go up with the position of the most significant set bit in the dividend:
if (*res > div_u64(ULLONG_MAX - val, base))
which is as maximal as possible.
Worse, on 32-bit arches, more than one of these division instructions
may be required per digit.
So, assuming we don't support a base of more than 16, skip the check if the
top nibble of the result is not set at this point.
Signed-off-by: David Howells <dhowells@redhat.com>
[ Changed it to not dereference the pointer all the time - even if the
compiler can and does optimize it away, the code just looks cleaner.
And edited the top nybble test slightly to make the code generated on
x86-64 better in the loop - test against a hoisted constant instead of
shifting and testing the result ] Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Russell King [Tue, 7 Feb 2012 09:47:21 +0000 (09:47 +0000)]
ARM: omap: fix broken twl-core dependencies and ifdefs
In commit aeb5032b3f, a dependency on IRQ_DOMAIN was added, which causes
regressions on previously working setups: a previously working non-DT
kernel configuration now loses its PMIC support. The lack of PMIC
support in turn causes the loss of other functionality the kernel had.
This dependency was added because the driver now registers its
interrupts with the IRQ domain code, presumably to prevent a build error.
The result is that OMAP3 oopses in the vp.c code (fixed by a previous
commit) due to the lack of PMIC support.
However, even with IRQ_DOMAIN enabled, the driver oopses:
This happens because we try to register an IRQ domain with a NULL ops
structure, and the first thing irq_domain_add() does is try to
dereference this ops structure.
So, fix the problem by getting rid of the incorrect OF_IRQ ifdef and
wrapping the IRQ domain bits of the driver with an IRQ_DOMAIN ifdef
instead.
Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Tue, 7 Feb 2012 09:44:55 +0000 (09:44 +0000)]
ARM: omap: fix oops in drivers/video/omap2/dss/dpi.c
When a PMIC is not found, this driver is unable to obtain its
'vdds_dsi_reg' regulator. Even through its initialization function
fails, other code still calls its enable function, which fails to
check whether it has this regulator before asking for it to be enabled.
This fixes the oops, however a better fix would be to sort out the
upper layers to prevent them calling into a module which failed to
initialize.
Stephen Boyd [Tue, 7 Feb 2012 18:42:33 +0000 (19:42 +0100)]
ARM: 7322/1: Print BUG instead of undefined instruction on BUG_ON()
The ARM kernel uses undefined instructions to implement
BUG/BUG_ON(). This leads to problems where people don't read one
line above the Oops message and see the "kernel BUG at ..."
message and so they wrongly assume the kernel has hit an
undefined instruction.
This should prevent people from thinking the BUG_ON was an
undefined instruction when it was actually intentional.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Acked-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Stephen Boyd [Tue, 7 Feb 2012 18:42:07 +0000 (19:42 +0100)]
ARM: 7321/1: cache-v7: Disable preemption when reading CCSIDR
armv7's flush_cache_all() flushes caches via set/way. To
determine the cache attributes (line size, number of sets,
etc.) the assembly first writes the CSSELR register to select a
cache level and then reads the CCSIDR register. The CSSELR register
is banked per-cpu and is used to determine which cache level CCSIDR
reads. If the task is migrated between when the CSSELR is written and
the CCSIDR is read the CCSIDR value may be for an unexpected cache
level (for example L1 instead of L2) and incorrect cache flushing
could occur.
Disable interrupts across the write and read so that the correct
cache attributes are read and used for the cache flushing
routine. We disable interrupts instead of disabling preemption
because the critical section is only 3 instructions and we want
to call v7_dcache_flush_all from __v7_setup which doesn't have a
full kernel stack with a struct thread_info.
This fixes a problem we see in scm_call() when flush_cache_all()
is called from preemptible context and sometimes the L2 cache is
not properly flushed out.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Acked-by: Catalin Marinas <catalin.marinas@arm.com> Reviewed-by: Nicolas Pitre <nico@linaro.org> Cc: stable@vger.kernel.org Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Marc Zyngier [Tue, 7 Feb 2012 01:46:38 +0000 (02:46 +0100)]
ARM: 7320/1: Fix proc_info table alignment
With an admittedly exotic choice of configuration options
(CC_OPTIMIZE_FOR_SIZE, THUMB2, some other size-minimizing ones)
and compiler, the proc_info table can end up being misaligned,
and the kernel being unbootable (Error: unrecognized/unsupported
processor variant).
Forcing the alignement to 4 bytes in the linker script fixes the
issue.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Thomas Abraham [Wed, 8 Feb 2012 02:42:43 +0000 (11:42 +0900)]
ARM: EXYNOS: Add cpu-offset property in gic device tree node
Commit db0d4db22a78 ('ARM: gic: allow GIC to support non-banked setups)
requires a cpu-offset property to be specified for non-banked gic
controllers, which is the case for Exynos4.
Reported-and-Tested-by: Karol Lewandowski <k.lewandowsk@samsung.com> Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This commit brings exynos4-dt in line with recent changes to
mach-exynos tree, specifically:
- Fixes build break related to replacing plat/exynos4.h with
common.h in commit cc511b8d84d8 ("ARM: 7257/1: EXYNOS:
introduce arch/arm/mach-exynos/common.[ch]")
- Converts machine to use CONFIG_MULTI_IRQ_HANDLER as done for
other machines in commit 4e44d2cb95bd ("ARM: exynos4: convert
to CONFIG_MULTI_IRQ_HANDLER")
- Adds restart specifier as done for other machines in commit 9eb4859564d6 ("ARM: 7262/1: restart: EXYNOS: use new restart hook")
Signed-off-by: Karol Lewandowski <k.lewandowsk@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Cc: Thomas Abraham <thomas.abraham@linaro.org> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
John Fastabend [Sat, 28 Jan 2012 03:32:17 +0000 (03:32 +0000)]
ixgbe: ethtool: stats user buffer overrun
If the number of tx/rx queues changes the ethtool ioctl
ETHTOOL_GSTATS may overrun the userspace buffer. This
occurs because the general practice in user space to
query stats is to issue a ETHTOOL_GSSET cmd to learn the
buffer size needed, allocate the buffer, then call
ETHTOOL_GSTIRNGS and ETHTOOL_GSTATS. If the number of
real_num_queues is changed or flow control attributes
are changed after ETHTOOL_GSSET but before the
ETHTOOL_GSTRINGS/ETHTOOL_GSTATS a user space buffer
overrun occurs.
To fix the overrun always return the max buffer size
needed from get_sset_count() then return all strings
and stats from get_strings()/get_ethtool_stats().
This _will_ change the output from the ioctl() call
which could break applications and script parsing in
theory. I believe these changes should not break existing
tools because the only changes will be more {tx|rx}_queues
and the {tx|rx}_pb_* stats will always be returned.
Existing scripts already need to handle changing number
of queues because this occurs today depending on system
and current features. The {tx|rx}_pb_* stats are at the
end of the output and should be handled by scripts today
regardless.
Finally get_ethtool_stats and get_strings are free-form
outputs tools parsing these outputs should be defensive
anyways. In the end these updates are better then
having a tool segfault because of a buffer overrun.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
John Fastabend [Sat, 28 Jan 2012 01:22:35 +0000 (01:22 +0000)]
ixgbe: dcb: up2tc mapping lost on disable/enable CEE DCB state
Users expect the up2tc mapping to be maintained across a DCB
enable/disable/enable transition. And since we maintain all
the other DCB attributes we should do this for up2tc mappings
as well just to be consistent. Also without this we break
user space applications that expect this to occur that
previously worked.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Tested-by: Stephen Ko <stephen.s.ko@intel.com> Tested-by: Ross Brattain <ross.b.brattain@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Yi Zou [Sat, 7 Jan 2012 08:39:50 +0000 (08:39 +0000)]
ixgbe: do not update real num queues when netdev is going away
If the netdev is already in NETREG_UNREGISTERING/_UNREGISTERED state, do not
update the real num tx queues. netdev_queue_update_kobjects() is already
called via remove_queue_kobjects() at NETREG_UNREGISTERING time. So, when
upper layer driver, e.g., FCoE protocol stack is monitoring the netdev
event of NETDEV_UNREGISTER and calls back to LLD ndo_fcoe_disable() to remove
extra queues allocated for FCoE, the associated txq sysfs kobjects are already
removed, and trying to update the real num queues would cause something like
below:
Signed-off-by: Yi Zou <yi.zou@intel.com> Tested-by: Ross Brattain <ross.b.brattain@intel.com> Tested-by: Stephen Ko <stephen.s.ko@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Thu, 10 Nov 2011 09:09:17 +0000 (09:09 +0000)]
ixgbe: Fix broken dependency on MAX_SKB_FRAGS being related to page size
This patch fixes an issue in which RSC will generate corrupted frames when
PAGE_SIZE is larger than 8K. Specifically it looks like that in 2.6.39 a
change was made so that GRO would always have at least 16 frags available
for coalescing, but the ixgbe RSC logic was not updated. As such the RSC
feature would generate a frame larger than 64K and then overflow the value
in the IP length field.
To correct that I am now basing things on the PAGE_SIZE.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Tested-by: Stephen Ko <stephen.s.ko@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Greg Rose [Wed, 25 Jan 2012 07:59:37 +0000 (07:59 +0000)]
ixgbe: Fix case of Tx Hang in PF with 32 VFs
A check for the number of VFs allocated should have used a greater than
equal operator instead of just greater than. This caused allocation of
exactly 32 VFs to not enable the PF transmit and receive enables.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com> Tested-by: Robert E Garrett <robertX.e.garrett@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Greg Rose [Fri, 3 Feb 2012 00:54:13 +0000 (00:54 +0000)]
ixgbe: fix vf lookup
Recent addition of code to find already allocated VFs failed to take
account that systems with 2 or more multi-port SR-IOV capable controllers
might have already enabled VFs. Make sure that the VFs the function is
finding are actually subordinate to the particular instance of the adapter
that is looking for them and not subordinate to some device that has
previously enabled SR-IOV.
This bug exists in 3.2 stable as well as 3.3 release candidates.
CC: stable@vger.kernel.org Reported-by: David Ahern <daahern@cisco.com> Signed-off-by: Greg Rose <gregory.v.rose@intel.com> Tested-by: Robert E Garrett <robertX.e.garrett@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Greg Rose [Thu, 2 Feb 2012 23:51:43 +0000 (23:51 +0000)]
igb: fix vf lookup
Recent addition of code to find already allocated VFs failed to take
account that systems with 2 or more multi-port SR-IOV capable controllers
might have already enabled VFs. Make sure that the VFs the function is
finding are actually subordinate to the particular instance of the adapter
that is looking for them and not subordinate to some device that has
previously enabled SR-IOV.
This is applicable to 3.2+ kernels.
CC: stable@vger.kernel.org Reported-by: David Ahern <daahern@cisco.com> Signed-off-by: Greg Rose <gregory.v.rose@intel.com> Tested-by: Robert E Garrett <robertX.e.garrett@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Takashi Iwai [Thu, 9 Feb 2012 08:32:19 +0000 (09:32 +0100)]
ALSA: hda - Fix mute-LED VREF value for new HP laptops
The new HP laptops turns off the mute LED with VREF50 or VREF80, but
not in HIZ unlike the previous models. Since VREF50 (also 80) works
with the previous models, let's use VREF50 for all.
In order to enable temperature mode aka automatic mode for the F75373 and
F75375 chips, the two FANx_MODE bits in the fan configuration register
need be set to 01, not 10.
Linus Torvalds [Thu, 9 Feb 2012 03:11:00 +0000 (19:11 -0800)]
Merge branch 'iommu/fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
One patch fixes an bug in the ARM/MSM IOMMU code which returned sucess
in the unmap function even when an error occured and the other patch
adds a workaround into the AMD IOMMU driver to better handle broken IVRS
ACPI tables (this patch fixes the case when a device is not listed in
the table but actually translated by the iommu).
* 'iommu/fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/msm: Fix error handling in msm_iommu_unmap()
iommu/amd: Work around broken IVRS tables
Linus Torvalds [Thu, 9 Feb 2012 03:09:25 +0000 (19:09 -0800)]
Merge branch '3.3-rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending
This series contains pending target bug-fixes and cleanups for v3.3-rc3
that have been addressed the past weeks in lio-core.git.
Some of the highlights include:
- Fix handling for control CDBs with data greater than PAGE_SIZE (andy)
- Use IP_FREEBIND for iscsi-target to address network portal creation
issues with systemd (dax)
- Allow PERSISTENT RESERVE IN for non-reservation holder (marco)
- Fix iblock se_dev_attrib.unmap_granularity (marco)
- Fix unsupported WRITE_SAME sense payload handling (martin)
- Add workaround for zero-length control CDB handling (nab)
- Fix discovery with INADDR_ANY and IN6ADDR_ANY_INIT (nab)
- Fix target_submit_cmd() exception handling (nab)
- Return correct ASC for unimplemented VPD pages (roland)
- Don't zero pages used for data buffers (roland)
- Fix return code of core_tpg_.*_lun (sebastian)
* '3.3-rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (26 commits)
target: Fix unsupported WRITE_SAME sense payload
iscsi: use IP_FREEBIND socket option
iblock: fix handling of large requests
target: handle empty string writes in sysfs
iscsi_target: in_aton needs linux/inet.h
target: Fix iblock se_dev_attrib.unmap_granularity
target: Fix target_submit_cmd() exception handling
target: Change target_submit_cmd() to return void
target: accept REQUEST_SENSE with 18bytes
target: Fail INQUIRY commands with EVPD==0 but PAGE CODE!=0
target: Return correct ASC for unimplemented VPD pages
iscsi-target: Fix discovery with INADDR_ANY and IN6ADDR_ANY_INIT
target: Allow control CDBs with data > 1 page
iscsi-target: Fix up a few assignments
iscsi-target: make one-bit bitfields unsigned
iscsi-target: Fix double list_add with iscsit_alloc_buffs reject
iscsi-target: Fix reject release handling in iscsit_free_cmd()
target: fix return code of core_tpg_.*_lun
target: use save/restore lock primitive in core_dec_lacl_count()
target: avoid multiple outputs in scsi_dump_inquiry()
...
Linus Torvalds [Thu, 9 Feb 2012 03:05:47 +0000 (19:05 -0800)]
Merge tag 'spi-for-linus' of git://git.secretlab.ca/git/linux-2.6
SPI bug fixes for v3.3-rc2
Minor SPI device driver changes. A rename of the pch_spi_pcidev symbol
that merely eliminates a modpost warning, and a Kconfig change to allow
the Samsung spi driver to build on EXYNOS.
* tag 'spi-for-linus' of git://git.secretlab.ca/git/linux-2.6:
spi-topcliff-pch: rename pch_spi_pcidev to pch_spi_pcidev_driver
spi: Add spi-s3c64xx driver dependency on ARCH_EXYNOS4
Russell King [Thu, 9 Feb 2012 01:13:41 +0000 (17:13 -0800)]
pcmcia: fix socket refcount decrementing on each resume
This fixes a memory-corrupting bug: not only does it cause the warning,
but as a result of dropping the refcount to zero, it causes the
pcmcia_socket0 device structure to be freed while it still has
references, causing slab caches corruption. A fatal oops quickly
follows this warning - often even just a 'dmesg' following the warning
causes the kernel to oops.
While testing suspend/resume on an ARM device with PCMCIA support, and a
CF card inserted, I found that after five suspend and resumes, the
kernel would complain, and shortly die after with slab corruption.
WARNING: at include/linux/kref.h:41 kobject_get+0x28/0x50()
As the message doesn't give a clue about which kobject, and the built-in
debugging in drivers/base/power/main.c happens too late, this was added
right before each get_device():
+ /* now, add the new card */
+ pcmcia_bus_add(skt);
+ return 0;
+}
As can be seen, the original function called pcmcia_get_socket() and
pcmcia_put_socket() around the guts, whereas the replacement code
calls pcmcia_put_socket() only in one path. This creates an imbalance
in the refcounting.
Testing with pcmcia_put_socket() put removed shows that the bug is gone:
Tested-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Cc: Dominik Brodowski <linux@dominikbrodowski.net> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Hugh Dickins [Thu, 9 Feb 2012 01:13:40 +0000 (17:13 -0800)]
mm: fix UP THP spin_is_locked BUGs
Fix CONFIG_TRANSPARENT_HUGEPAGE=y CONFIG_SMP=n CONFIG_DEBUG_VM=y
CONFIG_DEBUG_SPINLOCK=n kernel: spin_is_locked() is then always false,
and so triggers some BUGs in Transparent HugePage codepaths.
asm-generic/bug.h mentions this problem, and provides a WARN_ON_SMP(x);
but being too lazy to add VM_BUG_ON_SMP, BUG_ON_SMP, WARN_ON_SMP_ONCE,
VM_WARN_ON_SMP_ONCE, just test NR_CPUS != 1 in the existing VM_BUG_ONs.
Signed-off-by: Hugh Dickins <hughd@google.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In current code, pltfm->als_vmin is set to LM3530_ALS_WINDOW_mV and
pltfm->als_vmax is 0. This does not make sense. I think what we want
here is setting pltfm->als_vmax to LM3530_ALS_WINDOW_mV.
Both als_vmin and als_vmax local variables will be set to
pltfm->als_vmin and pltfm->als_vmax by a few lines latter. Thus also
remove a redundant assignment for als_vmin and als_vmax in this patch.
Signed-off-by: Axel Lin <axel.lin@gmail.com> Cc: Shreshtha Kumar Sahu <shreshthakumar.sahu@stericsson.com> Acked-by: Milo(Woogyom) Kim <milo.kim@ti.com> Tested-by: Milo(Woogyom) Kim <milo.kim@ti.com> Cc: Richard Purdie <rpurdie@rpsys.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mel Gorman [Thu, 9 Feb 2012 01:13:38 +0000 (17:13 -0800)]
mm: compaction: check for overlapping nodes during isolation for migration
When isolating pages for migration, migration starts at the start of a
zone while the free scanner starts at the end of the zone. Migration
avoids entering a new zone by never going beyond the free scanned.
Unfortunately, in very rare cases nodes can overlap. When this happens,
migration isolates pages without the LRU lock held, corrupting lists
which will trigger errors in reclaim or during page free such as in the
following oops
The "X" in the taint flag means that external modules were loaded but but
is unrelated to the bug triggering. The real problem was because the PFN
layout looks like this
The fix is straight-forward. isolate_migratepages() has to make a
similar check to isolate_freepage to ensure that it never isolates pages
from a zone it does not hold the LRU lock for.
This was discovered in a 3.0-based kernel but it affects 3.1.x, 3.2.x
and current mainline.
Signed-off-by: Mel Gorman <mgorman@suse.de> Acked-by: Michal Nazarewicz <mina86@mina86.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>