Rafał Miłecki [Sun, 19 Jun 2011 10:17:21 +0000 (12:17 +0200)]
b43: HT-PHY: switch radio to requested channel
Switching channel happens after specific SHM write to B43_SHM_SH_CHAN.
This is the way we found it in BCM4331 MMIO dumps. By comparing with
N-PHY code we noticed there is routing used for SYN and TX/RX.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rafał Miłecki [Sun, 19 Jun 2011 00:18:11 +0000 (02:18 +0200)]
b43: HT-PHY: implement killing radio
Closed drivers kill radio right after reading radio version and MACCTL,
so it was easy to find related PHY ops:
phy_read(0x0810) -> 0x0000
phy_write(0x0810) <- 0x0000
To find out the mask of above OP, MMIO hack was used to fake read val:
phy_read(0x0810) -> 0xffff
phy_write(0x0810) <- 0x0000
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mike McCormack [Mon, 20 Jun 2011 01:47:51 +0000 (10:47 +0900)]
rtlwifi: rtl8192{c,ce,cu,se}: Remove comparisons of booleans with true
These are a potential source of confusion, as most C code treats all
non-zero values as true.
Signed-off-by: Mike McCormack <mikem@ring3k.org> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mike McCormack [Mon, 20 Jun 2011 01:46:05 +0000 (10:46 +0900)]
rtlwifi: rtl8192cu: Remove unused parameter
rtl_ps_set_rf_state's protect_or_not parameter is not set to
true anywhere, except for commented out code.
It enables some legacy locking code, which is no longer used,
so delete the parameter and the old locking code.
Signed-off-by: Mike McCormack <mikem@ring3k.org> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mike McCormack [Mon, 20 Jun 2011 01:44:58 +0000 (10:44 +0900)]
rtlwifi: Fix typo in variable name
offchan_deley should be offchan_delay
Signed-off-by: Mike McCormack <mikem@ring3k.org> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rafał Miłecki [Fri, 17 Jun 2011 23:01:59 +0000 (01:01 +0200)]
bcma: clean exports of functions
Function managing IRQs is needed for external drivers like b43.
On the other side we do not expect writing any hosts drivers outside of
bcma, so this is safe to do not export functions related to this.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_hw: make sure PAPRD training is properly done
checking the status of PAPRD_AGC2_POWER(Log(ADC_power) measured after
last gain-change in dB) field suggests whether the PAPRD is completely/properly
done. This is an additional check apart from polling for PAPRD done bit being set.
Susinder suggests that the ideal power range value should be
0xf0 to 0xfe. With AR9382 we do have the values in this range. to have a
common check for all platforms we take agc2_power should be atleast greater
than 0xe0
Cc: susinder@qca.qualcomm.com Cc: senthilb@qca.qualcomm.com Cc: kmuthusa@qca.qualcomm.com Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k: Fix a corner case failure in sending PAPRD frames in HT40
when the AP is configured with HT40/2.4GHz and when PAPRD is enabled in station
we have PAPRD training frames never sent out because of the following
failure "PAPRD target power delta out of range". This consistently happens
in channel 10,11 in Over The Air testing and rarely in channel 6 under wired
setup.
the reason behind this issue is all the HT40 rates target power
are 0 when we operate in channel 10/11 at 2.4GHz
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Kalle Valo [Mon, 13 Jun 2011 22:35:04 +0000 (01:35 +0300)]
rtlwifi: include mac80211.h from core.h
core.h references ieee80211_ops but doesn't include mac80211.h, which issues
a warning once mac80211-compat.h is taken into use.
Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Kalle Valo <kvalo@adurom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Kalle Valo [Mon, 13 Jun 2011 22:34:57 +0000 (01:34 +0300)]
zd1211rw: include mac80211.h from zd_chip.h
zd_chip.h contains one function with a pointer to ieee80211_hw but doesn't
include mac80211.h. As a temporary solution include mac80211.h to avoid
a warning.
Signed-off-by: Kalle Valo <kvalo@adurom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since there is no protection around SYNC host command mechanism, at least WARN
when collision happens between two SYNC host comamnds. I am not sure there is a
real issue (beyond the HCMD_ACTIVE flag maintenance) with having two SYNC host
commands at the same time, but at least now, we will know about it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Bus specific layer must know how to return the struct device* of the device.
Implement that as a callback of iwl_bus_ops and use that callback instead of
using the priv->pdev pointer which is meant to disappear soon.
Since the struct device * is needed in hot path, iwl_bus holds a pointer to it
instead of calling get_dev all the time.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
iwl_bus will represent a bus, and iwl_bus_ops all the operations that can be
done on this bus.
For the moment only set_prv_data is implemented. More to come...
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
iwlagn: add a iwl_pci.[ch] files that will contain all PCI specific code
Move some PCI functionality to the new iwl_pci.[ch] files:
* the PCI_DEVICE_TABLE
* the pci_driver struct definition
* the PCI probe / remove functions
* the PCI suspend / resume functions
All these functions are now split: the trigger comes from the PCI layer which
calls to the bus generic code located in the other files.
This is the beginning only. There are still a lot of PCI related code needs
to be gathered.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
iwlagn: don't disable interrupts after the NIC has been reset
It is superfluous to disable the interrupts after we reset the NIC. The only
entity that could enable the interrupts after the NIC is reset is the driver.
So remove this pointless action.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Rafał Miłecki [Wed, 15 Jun 2011 23:59:20 +0000 (01:59 +0200)]
b43: HT-PHY: implement switching analog
Turning it on is always done between reading PHY version and radio
version, so it was easy to find it in MMIO dumps from ndiswrapper.
Turning off is done by writing different values to the same registers.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rafał Miłecki [Wed, 15 Jun 2011 23:59:19 +0000 (01:59 +0200)]
b43: HT-PHY: implement radio ops
Every PHY has some specific bit used for reading radio regs. Analyze of
MMIO dumps from BCM4331 and ndiswrapper has shown it is 0x200 for HT.
radio_read(0x037f) -> 0x0073
radio_write(0x017f) <- 0x0072
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pavel Roskin [Wed, 15 Jun 2011 22:03:22 +0000 (18:03 -0400)]
ath5k: minor cleanup
Move an extern variable declaration to a header file. Prefix all
functions with "ath5k_". Make ath5k_intr() static. Remove unneeded
forward declarations. Remove pointless "extern" in a function
declaration.
Signed-off-by: Pavel Roskin <proski@gnu.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
during suspend/resume ath9k_stop will always call ath_radio_disable
which will inturn call ath9k_hw_configpcipowersave, so no need to call
it explicitly in ath9k_stop
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Dan Carpenter [Wed, 15 Jun 2011 13:10:10 +0000 (16:10 +0300)]
iwlegacy: fix up brokenness caused by cleanup
Patch 7f1f9742514 "iwlegacy: refactor iwl4965_mac_channel_switch"
reversed a test and also it changed a spin_lock_irq() to
spin_lock(). I assume the spin_lock change was a mistake because
the unlock was left as spin_unlock_irq().
Signed-off-by: Dan Carpenter <error27@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add few debug messages for some of the possible scenarios
where we can detect PAPRD failures. this will help us to be
sure that we had really enabled PAPRD
Cc: susinder@qca.qualcomm.com Cc: senthilb@qca.qualcomm.com Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
drivers/net/wireless/libertas/if_spi.c: In function ‘if_spi_init_card’:
drivers/net/wireless/libertas/if_spi.c:1035: warning: unused variable ‘spi’
The variable is used only in a macro which uses the args only for DEBUG builds.
Remove the 'spi' variable completely.
Signed-off-by: Nikanth Karthikesan <nikanth@google.com> Acked-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Eliad Peller [Mon, 13 Jun 2011 09:47:30 +0000 (12:47 +0300)]
mac80211: add cancel_hw_scan() callback
When suspending, __ieee80211_suspend() calls ieee80211_scan_cancel(),
which will only cancel sw scan. In order to cancel hw scan, the
low-level driver has to cancel it in the suspend() callback. however,
this is too late, as a new scan_work will be enqueued (while the driver
is going into suspend).
Add a new cancel_hw_scan() callback, asking the driver to cancel an
active hw scan, and call it in ieee80211_scan_cancel().
Signed-off-by: Eliad Peller <eliad@wizery.com> Reviewed-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
warning message
drivers/ssb/driver_chipcommon_pmu.c: In function ssb_pmu_resources_init
drivers/ssb/driver_chipcommon_pmu.c:420:15: warning: updown_tab_size may
be used uninitilized in this function.
updown_tab_size and depend_tab_size may not be set in the bus->chip_id
switch statement, so set to 0 by default to avoid using uninitialized
stack space.
Signed-off-by: Connor Hansen <cmdkhh@gmail.com> Signed-off-by: Michael Buesch <m@bues.ch> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Paul Stewart [Fri, 10 Jun 2011 15:00:19 +0000 (07:00 -0800)]
mac80211: Start monitor work on restart
Trigger connection monitor on resume from suspend. Since we
have been sleeping, there is reason to suspect that we might
not still be associated. The speed of detecting loss of
{connection,authentication} is worth the cost of the small
additional traffic at resume.
Signed-off-by: Paul Stewart <pstew@chromium.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ilia Kolomisnky [Wed, 15 Jun 2011 03:52:26 +0000 (06:52 +0300)]
Bluetooth: Fix L2CAP connection establishment
In hci_conn_security ( which is used during L2CAP connection
establishment ) test for HCI_CONN_ENCRYPT_PEND state also
sets this state, which is bogus and leads to connection time-out
on L2CAP sockets in certain situations (especially when
using non-ssp devices )
Signed-off-by: Ilia Kolomisnky <iliak@ti.com> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patch implements a check in smp cmd pairing request and pairing
response to verify if encryption key maximum size is compatible in both
slave and master when SMP Pairing is requested. Keys are also masked to
the correct negotiated size.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org> Signed-off-by: Anderson Briglia <anderson.briglia@openbossa.org> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patch adds support for disconnecting the link when SMP procedure
takes more than 30 seconds.
SMP begins when either the Pairing Request command is sent or the
Pairing Response is received, and it ends when the link is encrypted
(or terminated). Vol 3, Part H Section 3.4.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Johan Hedberg [Tue, 14 Jun 2011 09:48:19 +0000 (12:48 +0300)]
Bluetooth: Fix accepting connect requests for defer_setup
When authentication completes we shouldn't blindly accept any pending
L2CAP connect requests. If the socket has the defer_setup feature
enabled it should still wait for user space acceptance of the connect
request. The issue only happens for non-SSP connections since with SSP
the L2CAP Connect request may not be sent for non-SDP PSMs before
authentication has completed successfully.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This adds support for starting SMP Phase 2 Encryption, when the initial
SMP negotiation is successful. This adds the LE Start Encryption and LE
Long Term Key Request commands and related events.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patch includes support for generating and sending the random value
used to produce the confirmation value.
Signed-off-by: Anderson Briglia <anderson.briglia@openbossa.org> Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patch adds initial support for verifying the confirmation value
that the remote side has sent.
Signed-off-by: Anderson Briglia <anderson.briglia@openbossa.org> Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patch implements SMP crypto functions called ah, c1, s1 and e.
It also implements auxiliary functions. All These functions are needed
for SMP keys generation.
Signed-off-by: Anderson Briglia <anderson.briglia@openbossa.org> Signed-off-by: Anderson Lizardo <anderson.lizardo@openbossa.org> Signed-off-by: Bruna Moreira <bruna.moreira@openbossa.org> Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Bluetooth: Add support for using the crypto subsystem
This will allow using the crypto subsystem for encrypting data. As SMP
(Security Manager Protocol) is implemented almost entirely on the host
side and the crypto module already implements the needed methods
(AES-128), it makes sense to use it.
There's now a new module option to enable/disable SMP support.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org> Signed-off-by: Anderson Briglia <anderson.briglia@openbossa.org> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This implementation only exchanges SMP messages between the Host and the
Remote. No keys are being generated. TK and STK generation will be
provided in further patches.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Start SMP procedure for LE connections. This modification intercepts
l2cap received frames and call proper SMP functions to start the SMP
procedure. By now, no keys are being used.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org> Signed-off-by: Anderson Briglia <anderson.briglia@openbossa.org> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
These simple commands will allow the SMP procedure to be started
and terminated with a not supported error. This is the first step
toward something useful.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org> Signed-off-by: Anderson Briglia <anderson.briglia@openbossa.org> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Bluetooth: Add state tracking to struct l2cap_chan
Now socket state is tracked by struct sock and channel state is tracked by
chan->state. At this point both says the same, but this is going to change
when we add AMP Support for example.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Add an abstraction layer between L2CAP core and its users (only
l2cap_sock.c now). The first function implemented is new_connection() that
replaces calls to l2cap_sock_alloc() in l2cap_core.c
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
projects / linux-beck.git / log