Ilya Faenson [Wed, 17 Jun 2015 21:30:56 +0000 (17:30 -0400)]
Bluetooth: hci_uart: Add new line discipline enhancements
Added the ability to flow control the UART, improved the UART baud
rate setting, transferred the speeds into line discipline from the
protocol and introduced the tty init function.
This patch removes the additional module_put() in disconnect_all_peers()
making a correct module refcount so that the module can be removed after
disabling 6lowpan through debugfs.
Bluetooth: 6lowpan: Fix double kfree of netdev priv
This patch removes the kfree of the netdev priv in device_event() upon
NETDEV_UNREGISTER event. The freeing of memory is taken care of by the
netdev destructor.
This patch moves the sysfs device used by the netdev from the device of
the first connected peer to the hci sysfs device. Using the sysfs device
of hci instead of the first connected device fixes this issue such that
the sysfs group of tx-0 and bt0 kobject are still present after the last
peer has been deleted and all sysfs entries can be removed.
Bluetooth: 6lowpan: Enable delete_netdev to be scheduled when last peer is deleted
This patch fixes an issue with the netdev not being unregistered when
the last peer is deleted. Removing the logical negation operator on the
boolean solves this issue. If the last peer is removed the condition
will be true, and the delete_netdev() is scheduled.
Alexander Aring [Wed, 17 Jun 2015 13:35:17 +0000 (15:35 +0200)]
mac802154: iface: fix order while interface up
This patch moves the hardware setting before calling the driver start
callback which activates the receive handling. The hardware setup
contains settings like address filtering which should be setup before
activate the receive handling on the transceiver. These setting are
protected by ieee802154_check_concurrent_iface check. This means we
need to set these registers once before calling drv_start and can't
be overwritten by other interfaces.
Signed-off-by: Alexander Aring <alex.aring@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Tedd Ho-Jeong An [Fri, 12 Jun 2015 23:20:05 +0000 (16:20 -0700)]
Bluetooth: btusb: Add routine for applying Intel DDC parameters
This patch adds the routine to apply the DDC parameter from device
specific ddc file.
Once the device is rest to operational mode, optionally, it can
download the device specific configration (DDC) parameters before
the BlueZ starts the stack initialization.
It opens the DDC file based on HW_VARIANT and DEV_REVISION and
send ID/Value with HCI_Intel_Write_DDC command.
Format of DDC file
DDC file contains one or more number of DDC structure.
DDC Structure
It has 'Length' field of one octet, DDC 'ID' field of
two octets followed by the array of DDC 'Value' that gives
the value of parameters itself.
'Length' contains the length of DDC 'ID' and DDC 'Value'.
+------------+----------+
| Size(byte) | Name |
+------------+----------+
| 1 | Length |
+------------+----------+
| 2 | ID |
+------------+----------+
| Length - 2 | Value |
+------------+----------+
Signed-off-by: Tedd Ho-Jeong An <tedd.an@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Chan-yeol Park [Wed, 17 Jun 2015 12:10:39 +0000 (21:10 +0900)]
Bluetooth: hci_uart: Fix dereferencing of ERR_PTR
If h4_recv_buf() return ERR_PTR instead sk_buff pointer, it should be
cleared once PTR_ERR is completed for the further dereference such as
h4_recv(), or h4_close().
Signed-off-by: Chan-yeol Park <chanyeol.park@samsung.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Alexander Aring [Tue, 16 Jun 2015 09:07:42 +0000 (11:07 +0200)]
at86rf230: fix phy settings while sleeping
While in sleep state then we can't access the at86rf2xx registers. This
patch checks if the transceiver is in sleep state before sending spi
messages via regmap. Regmap is used on every driver ops callback except
for receive and xmit handling, but while receive and xmit handling the
phy should not be inside the sleep state.
Signed-off-by: Alexander Aring <alex.aring@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Alexander Aring [Sun, 14 Jun 2015 14:48:44 +0000 (16:48 +0200)]
fakelb: add xmit_async after stop testcase
This patch adds a suspended testcase into the xmit_async functionality.
In the hope that we can found race conditions when xmit_async is called
after an ieee802154_ops stop. This should never happen.
Signed-off-by: Alexander Aring <alex.aring@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Alexander Aring [Sat, 13 Jun 2015 20:15:54 +0000 (22:15 +0200)]
at86rf230: add support for sleep state
This patch adds support for sleep state when between stop and start
period. In this period the transceiver isn't used by the subsystem, in
this time we disable the irq and going into the sleep state.
Signed-off-by: Alexander Aring <alex.aring@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Alexander Aring [Sat, 13 Jun 2015 20:15:52 +0000 (22:15 +0200)]
mac802154: iface: flush workqueue before stop
This patch flushs the workqueue which is currently used for xmit_sync
callback before calling stop driver-ops. Flush the queue will ensure all
pending tx frames are transmitted.
Signed-off-by: Alexander Aring <alex.aring@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Alexander Aring [Sat, 13 Jun 2015 20:15:51 +0000 (22:15 +0200)]
mac802154: iface: fix hrtimer cancel on ifdown
The interframe spacing timer is a per phy definition and is part of a
ieee802154_local structure. If we have possible multiple interfaces
ifdown one interface then the timer should not be cancled. First if the
last interface is down and the receive handling is stopped we should be
sure that the interframe spacing timer isn't run anymore.
Signed-off-by: Alexander Aring <alex.aring@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Johan Hedberg [Fri, 12 Jun 2015 10:04:47 +0000 (13:04 +0300)]
Bluetooth: Remove redundant check for ACL_LINK
The encryption key size is read only for BR/EDR (ACL_LINK) connections
so there's no need to check for it in the read_enc_key_size_complete()
callback.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Johan Hedberg [Thu, 11 Jun 2015 10:52:30 +0000 (13:52 +0300)]
Bluetooth: Use actual encryption key size for SMP over BR/EDR
When pairing over SMP over BR/EDR the generated LTK has by default the
same key size as the BR/EDR Link Key. Make sure we don't set our
Pairing Request/Response max value to anything higher than that.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Johan Hedberg [Thu, 11 Jun 2015 10:52:29 +0000 (13:52 +0300)]
Bluetooth: Read encryption key size for BR/EDR connections
Since Bluetooth 3.0 there's a HCI command available for reading the
encryption key size of an BR/EDR connection. This information is
essential e.g. for generating an LTK using SMP over BR/EDR, so store
it as part of struct hci_conn.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Johan Hedberg [Thu, 11 Jun 2015 10:52:28 +0000 (13:52 +0300)]
Bluetooth: Move SC-only check outside of BT_CONFIG branch
Checking for SC-only mode requirements when we get an encrypt change
event shouldn't be limited to the BT_CONFIG state but done any time
encryption changes.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Johan Hedberg [Thu, 11 Jun 2015 10:52:27 +0000 (13:52 +0300)]
Bluetooth: Add debugfs support for min LE encryption key size
This patch adds a debugfs control to set a different minimum LE
encryption key size. This is useful for testing that implementation of
the encryption key size handling is behaving correctly (e.g. that we
get appropriate 'Encryption Key Size' error responses when necessary).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Johan Hedberg [Thu, 11 Jun 2015 10:52:26 +0000 (13:52 +0300)]
Bluetooth: Add debugfs support for max LE encryption key size
This patch adds a debugfs control to set a different maximum LE
encryption key size. This is useful for testing that implementation of
the encryption key size handling is behaving correctly.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Johan Hedberg [Wed, 10 Jun 2015 08:11:20 +0000 (11:11 +0300)]
Bluetooth: Fix exposing full value of shortened LTKs
When we notify user space of a new LTK or distribute an LTK to the
remote peer the value passed should be the shortened version so that
it's easy to compare values in various traces. The core spec also sets
the requirements for the shortening/masking as:
"The masking shall be done after generation and before being
distributed, used or stored."
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Stefan Schmidt [Tue, 9 Jun 2015 09:49:27 +0000 (11:49 +0200)]
ieee802154: cc2520: check for return values in cc2520_filter()
neither ram nor register write return values have been checked here.
Checking both now. Assign ret with 0 as all other assignments are inside
if blocks and might not happen before we return ret.
Stefan Schmidt [Tue, 9 Jun 2015 08:52:26 +0000 (10:52 +0200)]
ieee802154/mrf24j40: make sure we do not override return values
If we run into an error during rx we set the the error code in ret, but override
it afterwards. Using a different variable for the extra case avoids this
situation.
CID: 1226982, 1226983 Signed-off-by: Stefan Schmidt <stefan@osg.samsung.com> Cc: Alan Ott <alan@signal11.us> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Stefan Schmidt [Mon, 8 Jun 2015 20:06:40 +0000 (22:06 +0200)]
mac802154/iface: remove superfluous WARN_ON call in slave_open()
This call was used before we aligned our code with the wireless code base. We
are wanted to handle this in the err: code path. Which would actually not work
because the WARN_ON() macro would reset the res value to 0 and thus we would
never hit err:. Removing it makes the code do what we actually intend.
Signed-off-by: Stefan Schmidt <stefan@osg.samsung.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch fixes the command length alignment issue for Intel Bluetooth
8260.
The length of parameters in the firmware downloading command must be
multiplication of 4. If not, the command must append Intel_NOP command
with extra parameters, zeros, at the end, and the firmware file is
already included Intel_NOP command for alignment.
This patch checks the next command and if the next command is Intel_NOP
command, it reads the Intel_NOP command and send them together.
For example, if the data from the firmware file looks like this:
8E FC 03 11 22 33 02 FC 03 00 00 00
Previously, btusb sends two commands:
09 FC 06 8E FC 03 11 22 33
09 FC 06 02 FC 03 00 00 00
This won't work because the length of parameters are 6 which violates
the 4 byte alignment.
This patch will append them together and send as one command:
09 FC 0C 8E FC 03 11 22 33 02 FC 03 00 00 00
Based on previous work from Tedd Ho-Jeong An <tedd.an@intel.com>
Reported-by: Tedd Ho-Jeong An <tedd.an@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Tested-by: Tedd Ho-Jeong An <tedd.an@intel.com> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Cc: stable@vger.kernel.org
Johan Hedberg [Mon, 8 Jun 2015 15:14:39 +0000 (18:14 +0300)]
Bluetooth: Fix encryption key size handling for LTKs
The encryption key size for LTKs is supposed to be applied only at the
moment of encryption. When generating a Link Key (using LE SC) from
the LTK the full non-shortened value should be used. This patch
modifies the code to always keep the full value around and only apply
the key size when passing the value to HCI.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Marcel Holtmann [Sat, 6 Jun 2015 04:06:49 +0000 (06:06 +0200)]
Bluetooth: Fix race condition with user channel and setup stage
During the initial setup stage of a controller, the low-level transport
is actually active. This means that HCI_UP is true. To avoid toggling
the transport off and back on again for normal operation the kernel
holds a grace period with HCI_AUTO_OFF that will turn the low-level
transport off in case no user is present.
The idea of the grace period is important to avoid having to initialize
all of the controller twice. So legacy ioctl and the new management
interface knows how to clear this grace period and then start normal
operation.
For the user channel operation this grace period has not been taken into
account which results in the problem that HCI_UP and HCI_AUTO_OFF are
set and the kernel will return EBUSY. However from a system point of
view the controller is ready to be grabbed by either the ioctl, the
management interface or the user channel.
This patch brings the user channel to the same level as the other two
entries for operating a controller.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Cc: stable@vger.kernel.org
Dmitry Tunin [Sat, 6 Jun 2015 17:29:25 +0000 (20:29 +0300)]
ath3k: add support of 13d3:3474 AR3012 device
BugLink: https://bugs.launchpad.net/bugs/1427680
This device requires new firmware files
AthrBT_0x11020100.dfu and ramps_0x11020100_40.dfu added to
/lib/firmware/ar3k/ that are not included in linux-firmware yet.
Dmitry Tunin [Sat, 6 Jun 2015 17:25:40 +0000 (20:25 +0300)]
ath3k: Add support of 0489:e076 AR3012 device
BugLink: https://bugs.launchpad.net/bugs/1462614
This device requires new firmware files
AthrBT_0x11020100.dfu and ramps_0x11020100_40.dfu added to
/lib/firmware/ar3k/ that are not included in linux-firmware yet.
Alexander Aring [Sat, 6 Jun 2015 15:30:50 +0000 (17:30 +0200)]
mac802154: remove unused hw_filt attribute
This patch removed an attribute from ieee802154_hw structure which is
never used inside kernel. Address information are stored inside wpan_dev
nowadays.
Alexander Aring [Sat, 6 Jun 2015 15:30:49 +0000 (17:30 +0200)]
mac802154: cleanup ieee802154 hardware flags
This patch changes the ieee802154 hardware flags to enums and setting the
flag values with the BIT macro. Additional this patch changes the
commenting style for matching usual kernel style.
Alexander Aring [Sat, 6 Jun 2015 15:30:48 +0000 (17:30 +0200)]
mac802154: remove aack hw flag
This patch removes the hardware auto acknowdledge flag which indicates
that the transceiver supports this handling. This flag is never
evaluated inside mac802154 and all transceivers should support this
handling by default per hardware.
Suggested-by: Lennert Buytenhek <buytenh@wantstofly.org> Cc: Alan Ott <alan@signal11.us> Signed-off-by: Alexander Aring <alex.aring@gmail.com> Reviewed-by: Varka Bhadram <varkabhadram@gmail.com> Acked-by: Stefan Schmidt <stefan@osg.samsung.com> Acked-by: Varka Bhadram <varkabhadram@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Alexander Aring [Sat, 6 Jun 2015 15:30:47 +0000 (17:30 +0200)]
mac802154: cleanup address filtering flags
This patch changes the address filtering flags to enums and setting the
flag values with the BIT macro. Additional this patch changes the
commenting style for matching usual kernel style.
Alexander Aring [Sat, 6 Jun 2015 15:30:46 +0000 (17:30 +0200)]
mac802154: remove unneeded vif struct
This patch removes the virtual interface structure from sub if data
struct, because it isn't used anywhere. This structure could be useful
for give per interface information at softmac driver layer. Nevertheless
there exist no use case currently and it contains the interface type
information currently. This information is also stored inside wpan dev
which is now used to check on the wpan dev interface type.
Frederic Danis [Thu, 28 May 2015 09:25:05 +0000 (11:25 +0200)]
Bluetooth: hci_uart: Update Broadcom UART setup
Use btbcm helpers to perform controller setup.
Perform host UART reset to init speed between btbcm_patchram() and
btbcm_finalize(). This may be need because firmware loading may have
reseted controller UART to init speed.
Frederic Danis [Thu, 28 May 2015 09:25:04 +0000 (11:25 +0200)]
Bluetooth: btbcm: Add helper functions for UART setup
Firmware loading may reset the controller UART speed and needs to set
host UART speed back to init speed.
UART drivers setup is split in 3 parts:
- btbcm_initialize() resets the controller and returns the firmware
name based on controller revision and sub_version.
- btbtcm_patchram() (already existing and public), which takes the
firmware name as parameter, requests the firmware and loads it to
the controller.
- btbcm_finalize() which resets the controller, reads local version
and checks if the controller address is a default one or not.
Remove firmware name retrieval for UART controllers from
btbcm_setup_patchram().
Frederic Danis [Thu, 28 May 2015 09:25:01 +0000 (11:25 +0200)]
Bluetooth: btbcm: Move request/release_firmware()
Move request/release_firmware() out of btbcm_patchram().
This allows a better error management, if request_firmware() returns an
error then the controller will be used without firmware loading and 0 is
returned.
This will imply to change btbcm_patchram() to accept a firmware instead
of firmware name.
Varka Bhadram [Thu, 4 Jun 2015 07:37:36 +0000 (13:07 +0530)]
nl802154: export supported commands
This patch will export the supported commands by the devices
to the userspace. This will be useful to check if HardMAC
drivers can support a specific command or not.
struct ieee802154_addr_sa {
int addr_type;
u16 pan_id;
union {
u8 hwaddr[IEEE802154_ADDR_LEN];
u16 short_addr;
};
};
On most architectures there will be implicit structure padding here,
in two different places:
* In struct sockaddr_ieee802154, two bytes of padding between 'family'
(unsigned short) and 'addr', so that 'addr' starts on a four byte
boundary.
* In struct ieee802154_addr_sa, two bytes at the end of the structure,
to make the structure 16 bytes.
When calling recvmsg(2) on a PF_IEEE802154 SOCK_DGRAM socket, the
ieee802154 stack constructs a struct sockaddr_ieee802154 on the
kernel stack without clearing these padding fields, and, depending
on the addr_type, between four and ten bytes of uncleared kernel
stack will be copied to userspace.
We can't just insert two 'u16 __pad's in the right places and zero
those before copying an address to userspace, as not all architectures
insert this implicit padding -- from a quick test it seems that avr32,
cris and m68k don't insert this padding, while every other architecture
that I have cross compilers for does insert this padding.
The easiest way to plug the leak is to just memset the whole struct
sockaddr_ieee802154 before filling in the fields we want to fill in,
and that's what this patch does.
Alexander Aring [Tue, 2 Jun 2015 13:55:17 +0000 (15:55 +0200)]
ieee802154: 6lowpan: set ackreq when needed
This patch sets the acknowledge request bit inside the 802.15.4 mac
header when frame retries is 0 or above. The other frame retries value
which is -1 indicates that the transmitter doesn't care about an
acknowledge frame which will be ignored after transmitting if the node
sends anyway an ack frame after receiving. This is currently unnecessary
traffic if the max frame retries parameter is -1.
Signed-off-by: Alexander Aring <alex.aring@gmail.com> Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Varka Bhadram [Fri, 29 May 2015 05:26:55 +0000 (10:56 +0530)]
cc2520: fix CC2591 handling
This patch changes tha way of handling of cc2591-cc2520 combination
by moving amplified variable from platform data to private data.
This will be useful in other sections like tx power support.
Stefan Schmidt [Fri, 29 May 2015 08:51:25 +0000 (10:51 +0200)]
ieee802154/atusb: Add function for partial register writes
With this function we can set individual bits in the registers if needed.
With the old SR_VALUE macro we could only set one bit in the register
which was ok for some scenarios but not for all. With this subreg write
function we can now set more bits defined by the mask while not touching
the rest.
We start using it for the current SR_VALUE use case and will use it more
in upcoming patches.
Signed-off-by: Stefan Schmidt <stefan@osg.samsung.com> Reviewed-by: Varka Bhadram <varkabhadram@gmail.com> Acked-by: Alexander Aring <alex.aring@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
ieee802154: Fix generation of random EUI-64 addresses.
Currently, ieee802154_random_extended_addr() has a 50% chance of
generating a group (multicast) address, while this function is used
for generating station addresses (which can't be group addresses)
for interfaces that don't have a hardware-provided address.
Also, in case get_random_bytes() generates the EUI-64 address
00:00:00:00:00:00:00:00 (extremely unlikely), which is an invalid
address, ieee802154_random_extended_addr() reacts by changing it
to 01:00:00:00:00:00:00:00, which is an invalid station address as
well, as it is a group address.
This patch changes the address generation procedure to grab eight
random bytes, treat that as an EUI-64, and then clear the Group
address bit and set the Locally Administered bit, which is in
line with how eth_random_addr() generates random EUI-48s.
David S. Miller [Sun, 31 May 2015 08:07:06 +0000 (01:07 -0700)]
Merge tag 'batman-adv-for-davem' of git://git.open-mesh.org/linux-merge
Antonio Quartulli says:
====================
Included changes:
- checkpatch fixes
- code cleanup
- debugfs component is now compiled only if DEBUG_FS is selected
- update copyright years
- disable by default not-so-user-safe features
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
bpf: add missing rcu protection when releasing programs from prog_array
Normally the program attachment place (like sockets, qdiscs) takes
care of rcu protection and calls bpf_prog_put() after a grace period.
The programs stored inside prog_array may not be attached anywhere,
so prog_array needs to take care of preserving rcu protection.
Otherwise bpf_tail_call() will race with bpf_prog_put().
To solve that introduce bpf_prog_put_rcu() helper function and use
it in 3 places where unattached program can decrement refcnt:
closing program fd, deleting/replacing program in prog_array.
Fixes: 04fd61ab36ec ("bpf: allow bpf programs to tail-call other bpf programs") Reported-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Alexei Starovoitov <ast@plumgrid.com> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for net-next, they are:
1) default CONFIG_NETFILTER_INGRESS to y for easier compile-testing of all
options.
2) Allow to bind a table to net_device. This introduces the internal
NFT_AF_NEEDS_DEV flag to perform a mandatory check for this binding.
This is required by the next patch.
3) Add the 'netdev' table family, this new table allows you to create ingress
filter basechains. This provides access to the existing nf_tables features
from ingress.
4) Kill unused argument from compat_find_calc_{match,target} in ip_tables
and ip6_tables, from Florian Westphal.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
These patches are highly inspired by changes from Petri on bcmgenet, last patch
is a misc fix that I had pending for a while, but is not a candidate for 'net'
at this point.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Thu, 28 May 2015 22:24:44 +0000 (15:24 -0700)]
net: systemport: Add a check for oversized packets
Occasionnaly we may get oversized packets from the hardware which exceed
the nomimal 2KiB buffer size we allocate SKBs with. Add an early check
which drops the packet to avoid invoking skb_over_panic() and move on to
processing the next packet.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Thu, 28 May 2015 22:24:43 +0000 (15:24 -0700)]
net: systemport: rewrite bcm_sysport_rx_refill
Currently, bcm_sysport_desc_rx() calls bcm_sysport_rx_refill() at the end of Rx
packet processing loop, after the current Rx packet has already been passed to
napi_gro_receive(). However, bcm_sysport_rx_refill() might fail to allocate a new
Rx skb, thus leaving a hole on the Rx queue where no valid Rx buffer exists.
To eliminate this situation:
1. Rewrite bcm_sysport_rx_refill() to retain the current Rx skb on the
Rx queue if a new replacement Rx skb can't be allocated and DMA-mapped.
In this case, the data on the current Rx skb is effectively dropped.
2. Modify bcm_sysport_desc_rx() to call bcm_sysport_rx_refill() at the
top of Rx packet processing loop, so that the new replacement Rx skb is
already in place before the current Rx skb is processed.
This is loosely inspired from d6707bec5986 ("net: bcmgenet: rewrite
bcmgenet_rx_refill()")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Thu, 28 May 2015 22:24:42 +0000 (15:24 -0700)]
net: systemport: Pre-calculate and utilize cb->bd_addr
There is a 1:1 mapping between the software maintained control block in
priv->rx_cbs and the buffer address in priv->rx_bds, such that there is
no need to keep computing the buffer address when refiling a control
block.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Thu, 28 May 2015 14:00:46 +0000 (16:00 +0200)]
net: thunderx: add 64-bit dependency
The thunderx ethernet driver fails to build on architectures
that do not have an atomic readq() and writeq() function for
64-bit PCI bus access:
drivers/net/ethernet/cavium/thunder/thunder_bgx.c: In function 'bgx_reg_read':
include/asm-generic/io.h:195:23: error: implicit declaration of function 'readq' [-Werror=implicit-function-declaration]
It seems impossible to get this driver to work on most 32-bit
hardware, so it's better to add an explicit dependency, in
order to let us keep building 'allmodconfig' kernels on
all architectures.
As the driver is meant for the internal hardware on an arm64 SoC, this
is not a problem for usability. Allowing the build on all 64-bit
architectures rather than just CONFIG_ARM64 on the other hand means that
we get the benefit of build testing on x86.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 31 May 2015 06:35:35 +0000 (23:35 -0700)]
Merge branch 'mlx4-next'
Or Gerlitz says:
====================
mlx4 driver update, May 28, 2015
The 1st patch fixes an issue with a function running DPDK overriding
broadcast steering rules set by other functions. Please add this one
to your -stable queue.
The rest of the series from Matan and Ido deals with scaling the number
of IRQs that serve RoCE applications to be in par with the Ethernet driver.
changes from V0:
- addressed feedback from Sergei, removed extra blank line in patch #4
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Matan Barak [Sun, 31 May 2015 06:30:18 +0000 (09:30 +0300)]
net/mlx4_core: Make sure there are no pending async events when freeing CQ
When freeing a CQ, we need to make sure there are no
asynchronous events (on the ASYNC EQ) that could
relate to this CQ before freeing it.
This is done by introducing synchronize_irq.
Signed-off-by: Matan Barak <matanb@mellanox.com> Signed-off-by: Ido Shamay <idos@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Shamay [Sun, 31 May 2015 06:30:17 +0000 (09:30 +0300)]
net/mlx4_core: Move affinity hints to mlx4_core ownership
Now that EQs management is in the sole responsibility of mlx4_core,
the IRQ affinity hints configuration should be in its hands as well.
request_irq is called only once by the first consumer (maybe mlx4_ib),
so mlx4_en passes the affinity mask too late. We also need to request
vectors according to the cores we want to run on.
mlx4_core distribution of IRQs to cores is straight forward,
EQ(i)->IRQ will set affinity hint to core i.
Consumers need to request EQ vectors, according to their cores
considerations (NUMA).
Signed-off-by: Ido Shamay <idos@mellanox.com> Signed-off-by: Matan Barak <matanb@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Matan Barak [Sun, 31 May 2015 06:30:16 +0000 (09:30 +0300)]
net/mlx4: Add EQ pool
Previously, mlx4_en allocated EQs and used them exclusively.
This affected RoCE performance, as applications which are
events sensitive were limited to use only the legacy EQs.
Change that by introducing an EQ pool. This pool is managed
by mlx4_core. EQs are assigned to ports (when there are limited
number of EQs, multiple ports could be assigned to the same EQs).
An exception to this rule is the ASYNC EQ which handles various events.
Legacy EQs are completely removed as all EQs could be shared.
When a consumer (mlx4_ib/mlx4_en) requests an EQ, it asks for
EQ serving on a specific port. The core driver calculates which
EQ should be assigned to that request.
Because IRQs are shared between IB and Ethernet modules, their
names only include the PCI device BDF address.
Signed-off-by: Matan Barak <matanb@mellanox.com> Signed-off-by: Ido Shamay <idos@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Matan Barak [Sun, 31 May 2015 06:30:15 +0000 (09:30 +0300)]
net/mlx4_core: Demote simple multicast and broadcast flow steering rules
In SRIOV, when simple (i.e - Ethernet L2 only) flow steering rules are
created, always create them at MLX4_DOMAIN_NIC priority (instead of
the real priority the function created them at). This is done in order
to let multiple functions add broadcast/multicast rules without
affecting other functions, which is necessary for DPDK in SRIOV.
Signed-off-by: Matan Barak <matanb@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Here's a set of patches intended for 4.2. The majority of the changes
are on the 802.15.4 side of things rather than Bluetooth related:
- All sorts of cleanups & fixes to ieee802154 and related drivers
- Rework of tx power support in ieee802154 and its drivers
- Support for setting ieee802154 tx power through nl802154
- New IDs for the btusb driver
- Various cleanups & smaller fixes to btusb
- New btrtl driver for Realtec devices
- Fix suspend/resume for Realtek devices
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patchset extends the mlx5_core driver to support Ethernet
functionality. The Ethernet functionality in the mlx5 driver is
integrated into the core driver and not as separated driver. The
IB functionality remains in the mlx5_ib driver as before.
This functionality will enable the Ethernet capability of Mellanox's new
famility of cards - ConnectX-4. Due to the fact that backword
compatability is being kept, existing Connect-IB cards that are using
this driver are fully working with the modified driver, and no issues
with current deployments should be seen.
Like the ConnectX-3 cards, ConnectX-4 is a VPI (Virtual Port Interface -
every port can be configured as Infiniband or Ethernet) card.
Unlike previous generations, the ConnectX-4 has a separate PCI function
per port.
The current code has a limitation that Infiniband and Ethernet port types
are mutually exclusive. When the driver is compiled with Ethernet
support, the Infiniband functionality is disabled and vice versa. To
control that we added the CONFIG_MLX5_CORE_EN config directive
which is 'n' by default, but can be changed by the user.
This limitation is short-lived and would be addressed soon.
As part of this patchset, mlx5_ifc.h was heavily modified [1]. This file
is now generated automatically from the device specification document.
Since this patch is too big for the mail server, it might be missing in
the mailing list, but could be pulled from an external git repository [2].
irq name selection is done at driver initialization and doesn't contain the
interface name as part of the irq name.
irq_balancer will still work thanks to an improvement introduced by Neil Horman
[3] to use sysfs instead of /proc/interrupts.
Patchset was applied on top of commit ed2dfd9 ("tcp/dccp: warn user for
preferred ip_local_port_range")
[1] - Patch 4/11 ("net/mlx5_core: HW data structs/types definitions preparation for mlx5 ehternet driver")
[2] - http://git.openfabrics.org/?p=~amirv/linux.git;a=shortlog;h=refs/heads/mlx5e_v1
[3] - kernel: da8d1c8 PCI/sysfs: add per pci device msi[x] irq listing (v5)
irq_balancer: 32a7757 Complete rework of how we detect and classify irqs
Thanks to Achiad, Saeed, Yevheny, Or and the whole team for making this happen,
Amir
Changes from V4:
- Removed Patch 3/12: net/mlx5_core: Add EQ renaming mechanism
- Patch 12/12: net/mlx5: Extend mlx5_core to support ConnectX-4 Ethernet functionality
- irq name is created on driver initialization, therefore it won't contain
the network interface name in it. This won't effect irq_balancer thanks to
patches introduced by Neil Horman to use sysfs instead of /proc/interrupts.
Changes from V3:
- PATCH 8/11: net/mlx5_core: Set/Query port MTU commands
- Return value directly - no need for err.
Changes from V2:
- Improved changelogs and cover-letter
- Added CONFIG_MLX5_EN to disable/enable the Ethernet functionality
- Moved en.h and wq.[ch] into the patch with data-path related code
Changes from V1:
- Added patch 1/12 ("net/mlx5_core,mlx5_ib: Do not use vmap() on coherent
memory")
Changes from V0:
- Removed V0 Patch 1/11 ("net/mlx5_core: Virtually extend work/completion queue
buffers by one page") due to misuse of DMA API. Thanks Dave.
- Patch 1/11 ("net/mlx5_core: Set irq affinity hints"):
- Use kcalloc instead of kzalloc
- Fix build error when CONFIG_CPUMASK_OFFSTACK=n. Driver loading will fail
now if cpumask allocation is failing.
- Using dev_to_node helper. Thanks, Ido.
- Patch 3/11 ("net/mlx5_core: HW data structs/types definitions preparation for
mlx5 ehternet driver")
- Removed Mellanox internal comment at the head of the file. Thanks Joe
- Patch 6/11 ("net/mlx5_core: Implement get/set port status")
- Use direct return of function's result. Thanks Sergei.
- Added Patch 8/11 ("net/mlx5_core: Set/Query port MTU commands")
- Patch 9/11 ("net/mlx5: Ethernet Datapath files")
- Use rq->wqe_sz instead of skb_end_offset. Thanks Ido.
- Use dma_wmb() when possible instead of wmb(). Thanks Alex.
- Fix checkpatch issues
- Patch 10/11 ("net/mlx5: ethernet resources handling")
- checkpatch issues
- Added missing include
- Patch 11/11 ("net/mlx5: Ethernet driver")
- checkpatch issues
- fixed typo
- Modified use of affinity hint
- Using dev_to_node helper. Thanks, Ido.
- Use new hardware commands from Patch 8/11 ("net/mlx5_core: Set/Query port
MTU commands") to get/set port MTU in hardware.
- Removed NETIF_F_SG since hardware ring wraparound is not supported
- Use dma_wmb() when possible instead of wmb(). Thanks Alex.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
projects / karo-tx-linux.git / log