tty: serial: men_z135_uart.c: Fix race between IRQ and set_termios()
Fix panic caused by a race between men_z135_intr() and men_z135_set_termios().
men_z135_intr() and men_z135_set_termios() both hold the struct uart_port::lock
spinlock, but men_z135_intr() does a spin_lock_irqsave() and
men_z135_set_termios() does a normal spin_lock(), which can lead to a deadlock
when an interrupt is called while the lock is being helt by
men_z135_set_termios().
This was discovered using a insmod, hardware looppback send/receive, rmmod
stress test.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de> Reviewed-by: Peter Hurley <peter@hurleysoftware.com> Cc: Andreas Werner <andreas.werner@men.de> Cc: stable@vger.kernel.org # v4.0+ Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
serial: 8250: bind to ALi Fast Infrared Controller (ALI5123)
This way this device can be used with irtty-sir -
at least on Toshiba Satellite A20-S103 it is not configured by default
and needs PNP activation before it starts to respond on I/O ports.
This device has actually its own driver (ali-ircc),
but this driver seems to be non-functional for a very long time
(see http://permalink.gmane.org/gmane.linux.irda.general/484
http://permalink.gmane.org/gmane.network.protocols.obex.openobex.user/943
https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=535070 ).
Stefan Wahren [Tue, 11 Aug 2015 11:46:01 +0000 (11:46 +0000)]
serial: mxs-auart: fix baud rate range
Currently mxs-auart doesn't care correctly about the baud rate divisor.
According to reference manual the baud rate divisor must be between
0x000000EC and 0x003FFFC0. So calculate the possible baud rate range
and use it for uart_get_baud_rate().
Juergen Borleis [Fri, 7 Aug 2015 10:47:04 +0000 (12:47 +0200)]
serial: mxs-auart: keep the AUART unit in reset state when not in use
Whenever the UART device driver gets closed from userland, the driver
disables the UART unit and then stops the clocks to save power.
The bit which disabled the UART unit is described as:
"UART Enable. If this bit is set to 1, the UART is enabled. Data
transmission and reception occurs for the UART signals. When the
UART is disabled in the middle of transmission or reception, it
completes the current character before stopping."
The important part is the "it completes the current character". Whenever
a reception is ongoing when the UART gets disabled (including the clock
off) the statemachine freezes and "remembers" this state on the next
open() when re-enabling the unit's clock.
In this case we end up receiving an additional bogus character
immediately.
The solution in this change is to switch the AUART unit into its reset
state on close() and only release it from its reset state on the next
open().
Note: when the unit is also used as system console it is always 'in use',
so we cannot reset it on close().
Peter Hung [Wed, 5 Aug 2015 06:44:53 +0000 (14:44 +0800)]
serial: 8250_pci: fix mode after S3/S4 resume for F81504/508/512
Fix RS232/485 mode incorrect setting after S3/S4 resume for F81504/508/512
We had add RS232/485 RTS control with fecf27a373f5. But when it
resume from S3/S4, the mode register 0x40 + 0x08 * idx + 7 will
rewrite to 0x01 (RS232 mode).
This patch will modify 2 sections.
One is pci_fintek_init(), if it called when first init, it will
write mode register with 0x01. If it called from S3/S4 resume,
it's will get the relative port data and pass it to
pci_fintek_rs485_config() with NULL rs485 parameter.
The another modification is in pci_fintek_rs485_config(). It'll
re-apply old configuration when the parameter rs485 is NULL.
Signed-off-by: Peter Hung <hpeter+linux_kernel@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jakub Kicinski [Fri, 31 Jul 2015 12:44:23 +0000 (14:44 +0200)]
sc16is7xx: support multiple devices
We currently register the uart driver during device probe
which makes it hard to support more than one chip.
Move the driver registration to module init/exit time and
preallocate space for up to 8 lines (4-8 chips).
Reported-by: Michael Allwright <michael.allwright@upb.de> Signed-off-by: Jakub Kicinski <kubakici@wp.pl> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jakub Kicinski [Fri, 31 Jul 2015 12:44:22 +0000 (14:44 +0200)]
sc16is7xx: save and use per-chip line number
In preparation of supporting multiple devices we should save
the per-chip line number (0 or 1), because the uart_port line
will reflect system-wide uart number and will be offseted for
chips other than the first to register.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Improve LCRH register access decision as ARM PL011 lcrh
register serve as both TX and RX, while other SOC may
implement TX and RX function with separated register.
Signed-off-by: Jun Nie <jun.nie@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jun Nie [Fri, 31 Jul 2015 07:49:17 +0000 (15:49 +0800)]
uart: pl011: Introduce register look up table
Introduce register look up table as different SOC venders
may have different register offset for the some register.
Signed-off-by: Jun Nie <jun.nie@linaro.org> Reviewed-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jun Nie [Fri, 31 Jul 2015 07:49:16 +0000 (15:49 +0800)]
uart: pl011: Introduce register accessor
Introduce register accessor to ease loop up table access
in later patch.
Signed-off-by: Jun Nie <jun.nie@linaro.org> Reviewed-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jun Nie [Fri, 31 Jul 2015 07:49:15 +0000 (15:49 +0800)]
uart: pl011: Rename regs with enumeration
Rename regs with enumeration to generalize register names.
Signed-off-by: Jun Nie <jun.nie@linaro.org> Reviewed-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Jun Nie <jun.nie@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Robert Baldyga [Fri, 31 Jul 2015 08:58:28 +0000 (10:58 +0200)]
serial: samsung: fix DMA for FIFO smaller than cache line size
So far DMA mode were activated when only number of bytes to send was
equal or greater than min_dma_size. Due to requirement that DMA transaction
buffer should be aligned to cache line size, the excessive bytes were
written to FIFO before starting DMA transaction. The problem occurred
when FIFO size were smaller than cache alignment, because writing all
excessive bytes to FIFO would fail. It happened in DMA mode when PIO
interrupts disabled, which caused driver hung.
The solution is to test if buffer is alligned to cache line size before
activating DMA mode, and if it's not, running PIO mode to align buffer
and then starting DMA transaction. In PIO mode, when interrupts are
enabled, lack of space in FIFO isn't the problem, so buffer aligning
will always finish with success.
Cc: <stable@vger.kernel.org> # v3.18+ Reported-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by: Robert Baldyga <r.baldyga@samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Marek Szyprowski [Fri, 31 Jul 2015 08:58:27 +0000 (10:58 +0200)]
serial: samsung: fix DMA mode enter condition for small FIFO sizes
Due to some of serial ports can have FIFO size smaller than cache line
size, and because of need to align DMA buffer address to cache line size,
it's necessary to calculate minimum number of bytes for which we want
to start DMA transaction to be at least cache line size. The simplest
way to meet this requirement is to get maximum of cache line size and
FIFO size.
Cc: <stable@vger.kernel.org> # v3.18+ Reported-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Robert Baldyga <r.baldyga@samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Hurley [Fri, 31 Jul 2015 20:59:52 +0000 (16:59 -0400)]
serial: core: Remove tty port activate() and shutdown() methods
serial core does not use tty_port_open() or tty_port_close(); serial
core defines and extends it's own tty open() and close() methods
(uart_open() and uart_close(), respectively).
Remove the tty_port activate() and shutdown() initializations, and
the uart_port_activate() function, which is never called.
NB: uart_port_shutdown() is used by uart_close() => uart_shutdown()
call chain (but not via the tty_port methods).
Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add "ti,dra742-uart" to the compatible list so the driver
workaround for UART module disable errata is enabled.
This does not break backward compatibility as existing DTBs
should continue to work with newer kernels albeit without the
capability to idle the UART module when DMA is used.
Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tty/serial: at91: fix I/O accesses on RHR and THR for AVR32
This patch fixes I/O accesses on the Receiver Holding Register and on the
Transmitter Holding Register. Indeed AVR32 can only perform 32bit I/O
accesses on registers: using 8bit I/O accesses would read or write garbage
data.
Fixes: commit b5199d468177 ("tty/serial: at91: add support to FIFOs") Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com> Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
serial: Allow compile test of GPIO consumers if !GPIOLIB
The GPIO subsystem provides dummy GPIO consumer functions if GPIOLIB is
not enabled. Hence drivers that depend on GPIOLIB, but use GPIO consumer
functionality only, can still be compiled if GPIOLIB is not enabled.
Relax the dependency on GPIOLIB if COMPILE_TEST is enabled, where
appropriate.
serial: 8250: Auto CTS control by HW if AFE enabled
According to DesignWare 8250 spec, if auto flow control
mode is enabled, a change in CTS does not cause an interrupt,
so sw-assisted CTS flow control mode will not work properly.
There reported an GPS firmware download failure issue, and we
verified the root cause is, the default sw-assisted CTS flow
control mode can not work properly since no interrupt when got
CTS signal.
This patch is to enable auto CTS mode by defaut if CRTSCTS
is enable for DesignWare 8250 controller.
serial: mpc52xx: let tx_empty callback return either 0 or TIOCSER_TEMT
Documenation/serial/driver requests that the tx_empty callback should
return 0 if there are still chars in the fifo or shifter or TIOCSER_TEMT
(0x01) if no character is pending to be sent.
Fix the mpc52xx serial driver to not return MPC52xx_PSC_SR_TXEMP (i.e.
0x0800) but TIOCSER_TEMT as documented.
serial: etraxfs-uart: use mctrl_gpio helpers for handling modem signals
In order to use the mctrl_gpio helpers, we change the DT bindings:
ri-gpios renamed to rng-gpios. cd-gpios renamed to dcd-gpios.
However, no in-tree dts/dtsi specifies these, so no worries.
Shenwei Wang [Thu, 30 Jul 2015 15:32:36 +0000 (10:32 -0500)]
Serial: imx: add dev_pm_ops to support suspend to ram/disk
When system goes into low power states like SUSPEND_MEM and
HIBERNATION, the hardware IP block may be powered off to reduce
the power consumption. This power down may cause problems on
some imx platforms, because the hardware settings are reset to
its power on default values which may differ from the ones when
it power off. This patch added the dev_pm_ops and implemented
two callbacks: suspend_noirq and resume_noirq, which will save
the necessory hardware parameters right before power down and
recover them before system uses the hardware.
Because added the dev_pm_ops, the old suspend/resume callbacks
under platform_driver will not be called any more. Changed their
prototypes and moved those two callbacks into dev_pm_ops too.
Signed-off-by: Shenwei Wang <shenwei.wang@freescale.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit e95044ba4fee93 ("tty: serial: imx.c: Reset UART before activating
interrupts") terribly messes up with the console on mx6 boards, so
let's revert it.
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"This update contains:
- the manual revert of the SYSCALL32 changes which caused a
regression
- a fix for the MPX vma handling
- three fixes for the ioremap 'is ram' checks.
- PAT warning fixes
- a trivial fix for the size calculation of TLB tracepoints
- handle old EFI structures gracefully
This also contains a PAT fix from Jan plus a revert thereof. Toshi
explained why the code is correct"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mm/pat: Revert 'Adjust default caching mode translation tables'
x86/asm/entry/32: Revert 'Do not use R9 in SYSCALL32' commit
x86/mm: Fix newly introduced printk format warnings
mm: Fix bugs in region_is_ram()
x86/mm: Remove region_is_ram() call from ioremap
x86/mm: Move warning from __ioremap_check_ram() to the call site
x86/mm/pat, drivers/media/ivtv: Move the PAT warning and replace WARN() with pr_warn()
x86/mm/pat, drivers/infiniband/ipath: Replace WARN() with pr_warn()
x86/mm/pat: Adjust default caching mode translation tables
x86/fpu: Disable dependent CPU features on "noxsave"
x86/mpx: Do not set ->vm_ops on MPX VMAs
x86/mm: Add parenthesis for TLB tracepoint size calculation
efi: Handle memory error structures produced based on old versions of standard
"No, the default values need to be set to the fallback types,
i.e. minimal supported mode. For WC and WT, UC is the fallback type.
When PAT is disabled, pat_init() does update the tables below to
enable WT per the default BIOS setup. However, when PAT is enabled,
but CPU has PAT -errata, WT falls back to UC per the default values."
The CQM task events are not safe to be called from within interrupt
context because they require performing an IPI to read the counter value
on all sockets. And performing IPIs from within IRQ context is a
"no-no".
Make do with the last read counter value currently event in
event->count when we're invoked in this context.
Reported-by: Peter Zijlstra <peterz@infradead.org> Signed-off-by: Matt Fleming <matt.fleming@intel.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Vikas Shivappa <vikas.shivappa@intel.com> Cc: Kanaka Juvva <kanaka.d.juvva@intel.com> Cc: Will Auld <will.auld@intel.com> Cc: <stable@vger.kernel.org> Link: http://lkml.kernel.org/r/1437490509-15373-1-git-send-email-matt@codeblueprint.co.uk Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Merge tag 'usb-4.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here's a few USB and PHY fixes for 4.2-rc4.
Nothing major, the shortlog has the full details.
All of these have been in linux-next successfully"
* tag 'usb-4.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (21 commits)
USB: OHCI: fix bad #define in ohci-tmio.c
cdc-acm: Destroy acm_minors IDR on module exit
usb-storage: Add ignore-device quirk for gm12u320 based usb mini projectors
usb-storage: ignore ZTE MF 823 card reader in mode 0x1225
USB: OHCI: Fix race between ED unlink and URB submission
usb: core: lpm: set lpm_capable for root hub device
xhci: do not report PLC when link is in internal resume state
xhci: prevent bus_suspend if SS port resuming in phase 1
xhci: report U3 when link is in resume state
xhci: Calculate old endpoints correctly on device reset
usb: xhci: Bugfix for NULL pointer deference in xhci_endpoint_init() function
xhci: Workaround to get D3 working in Intel xHCI
xhci: call BIOS workaround to enable runtime suspend on Intel Braswell
usb: dwc3: Reset the transfer resource index on SET_INTERFACE
usb: gadget: udc: core: Fix argument of dma_map_single for IOMMU
usb: gadget: mv_udc_core: fix phy_regs I/O memory leak
usb: ulpi: ulpi_init should be executed in subsys_initcall
phy: berlin-usb: fix divider for BG2
phy: berlin-usb: fix divider for BG2CD
phy/pxa: add HAS_IOMEM dependency
...
Merge tag 'trace-v4.2-rc2-fix3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull ftrace fix from Steven Rostedt:
"Back in 3.16 the ftrace code was redesigned and cleaned up to remove
the double iteration list (one for registered ftrace ops, and one for
registered "global" ops), to just use one list. That simplified the
code but also broke the function tracing filtering on pid.
This updates the code to handle the filtering again with the new
logic"
* tag 'trace-v4.2-rc2-fix3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
ftrace: Fix breakage of set_ftrace_pid
Merge branch 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/nvdimm
Pull libnvdimm fix from Dan Williams:
"A minor fix for the libnvdimm subsystem.
This is not critical. The problem can be worked around in userspace
by putting the namespace temporarily into raw mode
(ndctl_namespace_set_raw_mode() from libndctl), but that is awkward
for management utilities.
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/nvdimm:
libnvdimm: fix namespace seed creation
Merge tag 'md/4.2-fixes' of git://neil.brown.name/md
Pull md fixes from Neil Brown:
"Some md fixes for 4.2
Several are tagged for -stable.
A few aren't because they are not very, serious or because they are in
the 'experimental' cluster code"
* tag 'md/4.2-fixes' of git://neil.brown.name/md:
md/raid5: clear R5_NeedReplace when no longer needed.
Fix read-balancing during node failure
md-cluster: fix bitmap sub-offset in bitmap_read_sb
md: Return error if request_module fails and returns positive value
md: Skip cluster setup in case of error while reading bitmap
md/raid1: fix test for 'was read error from last working device'.
md: Skip cluster setup for dm-raid
md: flush ->event_work before stopping array.
md/raid10: always set reshape_safe when initializing reshape_position.
md/raid5: avoid races when changing cache size.
Dan Williams [Sat, 25 Jul 2015 03:42:34 +0000 (23:42 -0400)]
libnvdimm: fix namespace seed creation
A new BLK namespace "seed" device is created whenever the current seed
is successfully probed. However, if that namespace is assigned to a BTT
it may never directly experience a successful probe as it is a
subordinate device to a BTT configuration.
The effect of the current code is that no new namespaces can be
instantiated, after the seed namespace, to consume available BLK DPA
capacity. Fix this by treating a successful BTT probe event as a
successful probe event for the backing namespace.
Reported-by: Nicholas Moulin <nicholas.w.moulin@linux.intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Merge branch 'for-linus' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"Four smaller fixes for the current series. This contains:
- A fix for clones of discard bio's, that can cause data corruption.
From Martin.
- A fix for null_blk, where in certain queue modes it could access a
request after it had been freed. From Mike Krinkin.
- An error handling leak fix for blkcg, from Tejun.
- Also from Tejun, export of the functions that a file system needs
to implement cgroup writeback support"
* 'for-linus' of git://git.kernel.dk/linux-block:
block: Do a full clone when splitting discard bios
block: export bio_associate_*() and wbc_account_io()
blkcg: fix gendisk reference leak in blkg_conf_prep()
null_blk: fix use-after-free problem
Merge branch 'for-4.2-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata
Pull libata fixes from Tejun Heo:
"A couple important fixes.
- A block layer change which removed restriction on max transfer size
led to silent data corruption on some devices. A new quirk is
added to restore the old size limit for the reported device. If it
gets reported on more devices, we might have to consider restoring
the restriction for ATA devices by default.
- There finally is a SSD which is confirmed to cause data corruption
on TRIM regardless of which flavor is used. A new quirk is added
and the device is blacklisted
- Other device-specific workarounds"
* 'for-4.2-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
libata: Do not blacklist M510DC
libata: increase the timeout when setting transfer mode
libata: add ATA_HORKAGE_MAX_SEC_1024 to revert back to previous max_sectors limit
libata: force disable trim for SuperSSpeed S238
libata: add ATA_HORKAGE_NOTRIM
libata: add ATA_HORKAGE_BROKEN_FPDMA_AA quirk for HP 250GB SATA disk VB0250EAVER
ata: pmp: add quirk for Marvell 4140 SATA PMP
Merge tag 'mmc-4.2-rc3' of git://git.linaro.org/people/ulf.hansson/mmc
Pull MMC fixes from Ulf Hansson:
"Here are some mmc fixes intended for v4.2 rc4.
Note, most of the changes are for the sdhci-esdhc-imx controller,
which also required us to modify some related DTS files. Those
changes have been acked by the SoC maintainer.
MMC core:
- Fix a reference inbalance issue for power_ro_lock_show() sysfs handler
MMC host:
- omap_hsmmc: Fix IRQ errorhandling for CD, DTO, and CRC
- sdhci: Prevent a kernel panic while using DMA
- mtk-sd: Let it depend on HAS_DMA to prevent build errors
- sdhci-esdhc: Make 8BIT bus work
- sdhci-esdhc-imx: Fix some regressions for DT based platforms
- sdhci-pxav3: Fix a regression for DT based platforms"
* tag 'mmc-4.2-rc3' of git://git.linaro.org/people/ulf.hansson/mmc:
mmc: sdhci-pxav3: fix platform_data is not initialized
dts: mmc: fsl-imx-esdhc: remove fsl,cd-controller support
mmc: sdhci-esdhc-imx: clear f_max in boarddata
mmc: sdhci-esdhc-imx: remove duplicated dts parsing
mmc: sdhci: make max-frequency property in device tree work
mmc: sdhci-esdhc-imx: move all non dt probe code into one function
mmc: sdhci-esdhc-imx: fix cd regression for dt platform
dts: imx7: fix sd card gpio polarity specified in device tree
dts: imx25: fix sd card gpio polarity specified in device tree
dts: imx6: fix sd card gpio polarity specified in device tree
dts: imx53: fix sd card gpio polarity specified in device tree
dts: imx51: fix sd card gpio polarity specified in device tree
mmc: sdhci-esdhc: Make 8BIT bus work
mmc: block: Add missing mmc_blk_put() in power_ro_lock_show()
mmc: MMC_MTK should depend on HAS_DMA
mmc: sdhci check parameters before call dma_free_coherent
mmc: omap_hsmmc: Handle BADA, DEB and CEB interrupts
mmc: omap_hsmmc: Fix DTO and DCRC handling
Merge tag 'regulator-fix-v4.2-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"As well as some driver specific fixes there's several fixes here for
the core support for regulators supplying other regulators fixing both
an issue with ACPI support (which had never been tested before) and
some error handling and device removal issues that Javier noticed"
* tag 'regulator-fix-v4.2-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: core: Fix memory leak in regulator_resolve_supply()
regulator: core: Increase refcount for regulator supply's module
regulator: core: Handle full constraints systems when resolving supplies
regulator: 88pm800: fix LDO vsel_mask value
regulator: max8973: Fix up control flag option for bias control
regulator: s2mps11: Fix GPIO suspend enable shift wrapping bug
Merge tag 'spi-fix-v4.2-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A small collection of pretty much unremarkable driver specific fixes
here plus the addition of a new device ID to spidev which requires no
other code changes"
* tag 'spi-fix-v4.2-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: imx: Fix small DMA transfers
spi: zynq: missing break statement
spi: SPI_ZYNQMP_GQSPI should depend on HAS_DMA
spi: spidev: add compatible value for LTC2488
spi: img-spfi: fix support for speeds up to 1/4th input clock
Merge tag 'sound-4.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"This has been a calm week again: one minor lockdep fix for PCM core,
and the most of the rest are HD-audio quirks and fixups for various
chips and machines"
* tag 'sound-4.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Add headset mic pin quirk for a Dell device
ALSA: hda - remove one pin from ALC292_STANDARD_PINS
ALSA: hda - Add new GPU codec ID 0x10de007d to snd-hda
ALSA: hda: add new AMD PCI IDs with proper driver caps
ALSA: hda - Fix Skylake codec timeout
ALSA: hda - Add headset mic support for Acer Aspire V5-573G
ALSA: sparc: Add missing kfree in error path
ALSA: pcm: Fix lockdep warning with nonatomic PCM ops
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
Pull HID fixes from Jiri Kosina:
- kernel crash fixes for multitouch and wacom drivers, by Brent Adam
and Dan Carpenter
- cp2112 data packet race condition corruption fix, by Antonio Borneo
- a few new device IDs for wacom and microsoft drivers
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: cp2112: fix to force single data-report reply
HID: wacom: Enable pad device for older Bamboo Touch tablets
HID: multitouch: Fix fields from pen report ID being interpreted for multitouch
HID: microsoft: Add quirk for MS Surface Type/Touch cover
HID: wacom: NULL dereferences on error in probe()
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Aome amdgpu, one i915, one ttm and one hlcdc, nothing too scary.
All seems fine for about this time"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/ttm: recognize ARM64 arch in ioprot handler
drm/amdgpu/cz/dpm: properly report UVD and VCE clock levels
drm/amdgpu/cz: implement voltage validation properly
drm/amdgpu: add VCE harvesting instance query
drm/amdgpu: implement VCE 3.0 harvesting support (v4)
drm/amdgpu/dce10: Re-set VBLANK interrupt state when enabling a CRTC
drm/amdgpu/dce11: Re-set VBLANK interrupt state when enabling a CRTC
drm: Stop resetting connector state to unknown
drm/i915: Use two 32bit reads for select 64bit REG_READ ioctls
drm: atmel-hlcdc: fix vblank initial state
Commit 4104d326b670 ("ftrace: Remove global function list and call function
directly") simplified the ftrace code by removing the global_ops list with a
new design. But this cleanup also broke the filtering of PIDs that are added
to the set_ftrace_pid file.
Add back the proper hooks to have pid filtering working once again.
Cc: stable@vger.kernel.org # 3.16+ Reported-by: Matt Fleming <matt@console-pimps.org> Reported-by: Richard Weinberger <richard.weinberger@gmail.com> Tested-by: Matt Fleming <matt@console-pimps.org> Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Input: goodix - fix touch coordinates on WinBook TW100 and TW700
The touchscreen on the WinBook TW100 and TW700 don't match the default
display, with 0,0 touches being reported when touching at the bottom
right of the screen.
It's unfortunately impossible to detect this problem with data from the
DSDT, or other auxiliary metadata, so fallback to quirking this specific
model of tablet instead.
Devices may declare more LEDs than what is known to input-leds
(HID does this for some devices). Instead of showing ugly warnings
on connect and, even worse, oopsing on disconnect, let's simply
ignore LEDs that are not known to us.
Mark Brown [Fri, 24 Jul 2015 15:19:25 +0000 (16:19 +0100)]
Merge remote-tracking branches 'regulator/fix/88pm800', 'regulator/fix/max8973', 'regulator/fix/s2mps11' and 'regulator/fix/supply' into regulator-linus
DMA transfers must be greater than the watermark level size. spi_imx->rx_wml
and spi_imx->tx_wml contain the watermark level in 32bit words whereas struct
spi_transfer contains the transfer len in bytes. Fix the check if DMA is
possible for a transfer accordingly. This fixes transfers with sizes between
33 and 128 bytes for which previously was claimed that DMA is possible.
Fixes: f62caccd12c17e4 (spi: spi-imx: add DMA support) Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Cc: stable@vger.kernel.org Signed-off-by: Mark Brown <broonie@kernel.org>
x86/asm/entry/32: Revert 'Do not use R9 in SYSCALL32' commit
This change reverts most of commit 53e9accf0f 'Do not use R9 in
SYSCALL32'. I don't yet understand how, but code in that commit
sometimes fails to preserve EBP.
See https://bugzilla.kernel.org/show_bug.cgi?id=101061
"Problems while executing 32-bit code on AMD64"
Reported-and-tested-by: Krzysztof A. Sobiecki <sobkas@gmail.com> Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Andy Lutomirski <luto@amacapital.net> Cc: Oleg Nesterov <oleg@redhat.com> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Alexei Starovoitov <ast@plumgrid.com> Cc: Will Drewry <wad@chromium.org> Cc: Kees Cook <keescook@chromium.org> CC: x86@kernel.org Link: http://lkml.kernel.org/r/1437740203-11552-1-git-send-email-dvlasenk@redhat.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
mmc: sdhci-pxav3: fix platform_data is not initialized
pdev->dev.platform_data is not initialized if match is true in function
sdhci_pxav3_probe. Just local variable pdata is assigned the return value
from function pxav3_get_mmc_pdata().
static int sdhci_pxav3_probe(struct platform_device *pdev) {
struct sdhci_pxa_platdata *pdata = pdev->dev.platform_data;
...
if (match) {
ret = mmc_of_parse(host->mmc);
if (ret)
goto err_of_parse;
sdhci_get_of_property(pdev);
pdata = pxav3_get_mmc_pdata(dev);
}
...
}
After commit 8d86e4fcccf6 ("mmc: sdhci-esdhc-imx: Call mmc_of_parse()"),
we do not need those duplicated parsing anymore.
Note: fsl,cd-controller is also deleted due to the driver does
not support controller card detection anymore after switch to runtime pm.
And there's no user of it right now in device tree.
wp-gpios is kept because we're still support fsl,wp-controller,
so we need a way to check if it's gpio wp or controller wp.
mmc: sdhci: make max-frequency property in device tree work
Device tree provides option to specify the max freqency with property
"max-frequency" in dts and common parse function mmc_of_parse() will
parse it and use this value to set host->f_max to tell the MMC core
the maxinum frequency the host works.
However, current sdhci driver will finally overwrite this value with
host->max_clk regardless of the max-frequency property.
This patch makes sure not overwrite the max-frequency set from device
tree and do basic sanity check.
mmc: sdhci-esdhc-imx: move all non dt probe code into one function
This is an incremental fix of commit e62bd351b("mmc: sdhci-esdhc-imx: Do not break platform data boards").
After commit 8d86e4fcccf6 ("mmc: sdhci-esdhc-imx: Call mmc_of_parse()"),
we do not need to run the check of boarddata->wp_type/cd_type/max_bus_width
again for dt platform since those are already handled by mmc_of_parse().
Current code only exclude the checking of wp_type for dt platform which
does not make sense.
This patch moves all non dt probe code into one function.
Besides, since we only support SD3.0/eMMC HS200 for dt platform, the
support_vsel checking and ultra high speed pinctrl state are also merged
into sdhci_esdhc_imx_probe_dt.
Then we have two separately probe function for dt and non dt type.
This can make the driver probe more clearly.
mmc: sdhci-esdhc-imx: fix cd regression for dt platform
Current card detect probe process is that when driver finds a valid
ESDHC_CD_GPIO, it will clear the quirk SDHCI_QUIRK_BROKEN_CARD_DETECTION
which is set by default for all esdhc/usdhc controllers.
Then host driver will know there's a valid card detect function.
Commit 8d86e4fcccf6 ("mmc: sdhci-esdhc-imx: Call mmc_of_parse()")
breaks GPIO CD function for dt platform that it will return directly
when find ESDHC_CD_GPIO for dt platform which result in the later wrongly
to keep SDHCI_QUIRK_BROKEN_CARD_DETECTION for all dt platforms.
Then MMC_CAP_NEEDS_POLL will be used instead even there's a valid
GPIO card detect.
This patch adds back this function and follows the original approach to
clear the quirk if find an valid CD GPIO for dt platforms.
dts: imx7: fix sd card gpio polarity specified in device tree
cd-gpios polarity should be changed to GPIO_ACTIVE_LOW and wp-gpios
should be changed to GPIO_ACTIVE_HIGH.
Otherwise, the SD may not work properly due to wrong polarity inversion
specified in DT after switch to common parsing function mmc_of_parse().
dts: imx25: fix sd card gpio polarity specified in device tree
cd-gpios polarity should be changed to GPIO_ACTIVE_LOW and wp-gpios
should be changed to GPIO_ACTIVE_HIGH.
Otherwise, the SD may not work properly due to wrong polarity inversion
specified in DT after switch to common parsing function mmc_of_parse().
dts: imx6: fix sd card gpio polarity specified in device tree
cd-gpios polarity should be changed to GPIO_ACTIVE_LOW and wp-gpios
should be changed to GPIO_ACTIVE_HIGH.
Otherwise, the SD may not work properly due to wrong polarity inversion
specified in DT after switch to common parsing function mmc_of_parse().
dts: imx53: fix sd card gpio polarity specified in device tree
cd-gpios polarity should be changed to GPIO_ACTIVE_LOW and wp-gpios
should be changed to GPIO_ACTIVE_HIGH.
Otherwise, the SD may not work properly due to wrong polarity inversion
specified in DT after switch to common parsing function mmc_of_parse().
dts: imx51: fix sd card gpio polarity specified in device tree
cd-gpios polarity should be changed to GPIO_ACTIVE_LOW and wp-gpios
should be changed to GPIO_ACTIVE_HIGH.
Otherwise, the SD may not work properly due to wrong polarity inversion
specified in DT after switch to common parsing function mmc_of_parse().
Support for 8BIT bus with was added some time ago to sdhci-esdhc but
then missed to remove the 8BIT from the reserved bit mask which made
8BIT non functional.
Fixes: 66b50a00992d ("mmc: esdhc: Add support for 8-bit bus width and..") Signed-off-by: Joakim Tjernlund <joakim.tjernlund@transmode.se> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Vignesh R [Tue, 16 Jun 2015 10:37:18 +0000 (16:07 +0530)]
mmc: omap_hsmmc: Handle BADA, DEB and CEB interrupts
Sometimes BADA, DEB or CEB error interrupts occur when sd card is
unplugged during data transfer. These interrupts are currently ignored
by the interrupt handler. But, this results in card not being
recognised on subsequent insertion. This is because mmcqd is waiting
forever for the data transfer(for which error occurred) to complete.
Fix this, by reporting BADA, DEB, CEB errors to mmc-core as -EILSEQ, so
that the core can do appropriate handling.
Signed-off-by: Vignesh R <vigneshr@ti.com> Tested-by: Andreas Fenkart <afenkart@gmail.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
DTO/DCRC errors were not being informed to the mmc core since
commit ae4bf788ee9b ("mmc: omap_hsmmc: consolidate error report handling of
HSMMC IRQ"). This commit made sure 'end_trans' is never set on DTO/DCRC
errors. This is because after this commit 'host->data' is checked after
it has been cleared to NULL by omap_hsmmc_dma_cleanup().
Because 'end_trans' is never set, omap_hsmmc_xfer_done() is never invoked
making core layer not to be aware of DTO/DCRC errors. Because of this
any command invoked after DTO/DCRC error leads to a hang.
Fix this by checking for 'host->data' before it is actually cleared.
CC: stable@vger.kernel.org Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Vignesh R <vigneshr@ti.com> Tested-by: Andreas Fenkart <afenkart@gmail.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
During a node failure, We need to suspend read balancing so that the
reads are directed to the first device and stale data is not read.
Suspending writes is not required because these would be recorded and
synced eventually.
A new flag MD_CLUSTER_SUSPEND_READ_BALANCING is set in recover_prep().
area_resyncing() will respond true for the entire devices if this
flag is set and the request type is READ. The flag is cleared
in recover_done().
md-cluster: fix bitmap sub-offset in bitmap_read_sb
bitmap_read_sb is modifying mddev->bitmap_info.offset. This works for
the first bitmap read. However, when multiple bitmaps need to be opened
by the same node, it ends up corrupting the offset. Fix it by using a
local variable.
Also, bitmap_read_sb is not required in bitmap_copy_from_slot since
it is called in bitmap_create. Remove bitmap_read_sb().
md: Return error if request_module fails and returns positive value
request_module() can return 256 (process exited) in some cases,
which is not as specified in the documentation before the
request_module() definition. Convert the error to -ENOENT.
The positive error number results in bitmap_create() returning
a value that is meant to be an error but doesn't look like one,
so it is dereferenced as a point and causes a crash.
(not needed for stable as this is "experimental" code) Fixes: edb39c9deda8 ("Introduce md_cluster_operations to handle cluster functions") Signed-off-By: Goldwyn Rodrigues <rgoldwyn@suse.com> Signed-off-by: NeilBrown <neilb@suse.com>
md: Skip cluster setup in case of error while reading bitmap
If the bitmap read fails, the error code set is -EINVAL. However,
we don't check for errors and go ahead with cluster_setup.
Skip the cluster setup in case of error.
md/raid1: fix test for 'was read error from last working device'.
When we get a read error from the last working device, we don't
try to repair it, and don't fail the device. We simple report a
read error to the caller.
However the current test for 'is this the last working device' is
wrong.
When there is only one fully working device, it assumes that a
non-faulty device is that device. However a spare which is rebuilding
would be non-faulty but so not the only working device.
So change the test from "!Faulty" to "In_sync". If ->degraded says
there is only one fully working device and this device is in_sync,
this must be the one.
This bug has existed since we allowed read_balance to read from
a recovering spare in v3.0
Reported-and-tested-by: Alexander Lyakas <alex.bolshoy@gmail.com> Fixes: 76073054c95b ("md/raid1: clean up read_balance.") Cc: stable@vger.kernel.org (v3.0+) Signed-off-by: NeilBrown <neilb@suse.com>
Dave Airlie [Fri, 24 Jul 2015 01:52:35 +0000 (11:52 +1000)]
Merge tag 'topic/drm-fixes-2015-07-23' of git://anongit.freedesktop.org/drm-intel into drm-fixes
Regression fix for systemd getting confused about unknown connector state
after resume. Just stop setting the state to unknown, turned out to be a
silly idea anyway. What drivers imo really should do (and i915 still does
that) is forcing a full reprobe on resume to make sure connector changes
while suspended are caught. Most drivers seem to get this wrong. Otoh it
took us years to get fixes merged where some probe races resulted in
eating uevents, I guess userspace expectations for reliable hpd are just
really low :(
* tag 'topic/drm-fixes-2015-07-23' of git://anongit.freedesktop.org/drm-intel:
drm: Stop resetting connector state to unknown
Dave Airlie [Fri, 24 Jul 2015 01:51:18 +0000 (11:51 +1000)]
Merge branch 'drm-fixes-4.2' of git://people.freedesktop.org/~agd5f/linux into drm-fixes
Some amdgpu fixes.
* 'drm-fixes-4.2' of git://people.freedesktop.org/~agd5f/linux:
drm/amdgpu/cz/dpm: properly report UVD and VCE clock levels
drm/amdgpu/cz: implement voltage validation properly
drm/amdgpu: add VCE harvesting instance query
drm/amdgpu: implement VCE 3.0 harvesting support (v4)
drm/amdgpu/dce10: Re-set VBLANK interrupt state when enabling a CRTC
drm/amdgpu/dce11: Re-set VBLANK interrupt state when enabling a CRTC
Peter Hurley [Mon, 13 Jul 2015 02:49:13 +0000 (22:49 -0400)]
pty: Add debug message for ptmx open
Opens of /dev/ptmx don't use tty_open() so debug messages are
not printed for those opens; print a debug message with the
open count (which must always be 1) if TTY_DEBUG_HANGUP is defined.
NB: Each tty core source file undefs support for debug messages.
The relevant source file must be patched/edited to enable these
messages.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Hurley [Mon, 13 Jul 2015 02:49:12 +0000 (22:49 -0400)]
tty: core: Improve ldisc debug messages
Add debug messages for ldisc open and close, and remove
"closing ldisc" message from tty_ldisc_release(), because a
close message is now printed for both ldiscs; always print ldisc
pointer first so ldisc changes are easier to identify.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / linux-beck.git / log