ENGR00258733 WEIM-NOR: mtd: cfi_cmdset_0002: Do not release the mutex lock
The NOR(M29W256GL7AN6E) may suffers a write-buffer timeout during
the bonnie++/ubifs stress test. Micron has confirmed that it is
a silicon bug in the Nor.
This patch is just a workaround to fix this issue for this NOR.
With this patch, the read/write/erase will do in the synchronous way.
ENGR00257947 mtd: use memcpy to replace the memcpy_fromio
During the read of NOR, the kernel actually calls the inline_map_copy_from()
to read the data out. And inline_map_copy_from() will use the memcpy_fromio()
to do the real job.
The memcpy_fromio macro maps _memcpy_fromio() in the current code.
But the _memcpy_fromio() will use readb() to do the copy work one byte
by one byte. This makes the read performance of NOR very slow(about 2~3MB/s).
A similiar discussion could be found in:
http://lists.infradead.org/pipermail/linux-arm-kernel/2009-November/003860.html
This patch replace the memcpy_fromio with memcpy which is optimized by the
kernel.
The following is the result from mtd_speedtest with M29W256GL7AN6E:
=================================================
mtd_speedtest: MTD device: 2
mtd_speedtest: not NAND flash, assume page size is 512 bytes.
mtd_speedtest: MTD device size 4194304, eraseblock size 131072, page size 512,
count of eraseblocks 32, pages per eraseblock 256, OOB size 0
mtd_speedtest: testing eraseblock write speed
mtd_speedtest: eraseblock write speed is 845 KiB/s
mtd_speedtest: testing eraseblock read speed
mtd_speedtest: eraseblock read speed is 19504 KiB/s
mtd_speedtest: testing page write speed
mtd_speedtest: page write speed is 845 KiB/s
mtd_speedtest: testing page read speed
mtd_speedtest: page read speed is 19140 KiB/s
mtd_speedtest: testing 2 page write speed
mtd_speedtest: 2 page write speed is 846 KiB/s
mtd_speedtest: testing 2 page read speed
mtd_speedtest: 2 page read speed is 19320 KiB/s
mtd_speedtest: Testing erase speed
mtd_speedtest: erase speed is 233 KiB/s
mtd_speedtest: Testing 2x multi-block erase speed
mtd_speedtest: 2x multi-block erase speed is 225 KiB/s
mtd_speedtest: Testing 4x multi-block erase speed
mtd_speedtest: 4x multi-block erase speed is 224 KiB/s
mtd_speedtest: Testing 8x multi-block erase speed
mtd_speedtest: 8x multi-block erase speed is 225 KiB/s
mtd_speedtest: Testing 16x multi-block erase speed
mtd_speedtest: 16x multi-block erase speed is 225 KiB/s
mtd_speedtest: Testing 32x multi-block erase speed
mtd_speedtest: 32x multi-block erase speed is 225 KiB/s
mtd_speedtest: Testing 64x multi-block erase speed
mtd_speedtest: 64x multi-block erase speed is 224 KiB/s
mtd_speedtest: finished
=================================================
Fugang Duan [Mon, 19 Aug 2013 02:58:24 +0000 (10:58 +0800)]
ENGR00275619 net: fec: set reset phy gpio to high in .probe().
In .probe() call fec_of_init() to parse phy reset gpio, and
request the gpio for later use. For the init, we must set the
gpio to high to let phy power on.
Connecting two boards directly more than 2 hours, Ar8031 phy link
status generates glitch, which cause ethernet link down/up issue, but
ethernet still be active. There have three cases to validate the issue:
Item#1: If add performance stress test while runing IEEE1588, the link
down/up issue cannot be found.
Item#2: If insert switch between two net nodes and run IEEE1588 test,
the issue also cannot be found.
Item#3: If disable AR8031 SmartEEE feature, after two days overnight test,
no such issue found.
The issue is caused by phy Ar8031 SmartEEE feature, Item#1 and Item#2 can
prevent phy enter lpm mode, which match the Item#3 test result, so disable
SmartEEE feature to avoid the link issue generation.
Current driver only do phy reset in probe function, which is
not right. Since some phy clock is disabled after module probe,
the phy enter abnormal status, which needs do reset to recovery
the phy. And do ifconfig ethx up/down test, the phy also enter
abnormal status.
The log as:
libphy: 2188000.ethernet:04 - Link is Up - 10/Full
libphy: 2188000.ethernet:04 - Link is Up - 100/Full
libphy: 2188000.ethernet:04 - Link is Down
libphy: 2188000.ethernet:04 - Link is Up - 10/Half
libphy: 2188000.ethernet:04 - Link is Up - 10/Full
libphy: 2188000.ethernet:04 - Link is Up - 100/Full
...
So, do phy reset if ethx up/down or do clock enable/disable
operation.
Shengjiu Wang [Fri, 9 Aug 2013 06:45:51 +0000 (14:45 +0800)]
ENGR00274585-9 ASoC: change error message to debug message
This error message is not actual error, which is a warning. When using
FE/BE, if there is widget which is used by playback and capture route, then
this message will be printed.
Signed-off-by: Shengjiu Wang <b02247@freescale.com>
Robby Cai [Thu, 8 Aug 2013 03:23:54 +0000 (11:23 +0800)]
ENGR00274412-1 dma: pxp: Port ePxP driver to 3.10
It's ported from v3.5.7, which contains ePxP DMAENGINE driver and
a client driver named pxp_device. This patch also includes the changes:
- use uapi header file
- remove VM_RESERVED since it's deprecated, and drop redundant VM_IO flag
since it's automatically set in remap_pfn_range()
- use <linux/platform_data/dma-imx.h> instead of <mach/dma.h>
- use devm_kzalloc() instead in pxp_probe()
- use macro __KERNEL__ in pxp_dma uapi header to avoid definition conflict
Sandor Yu [Tue, 13 Aug 2013 08:55:20 +0000 (16:55 +0800)]
ENGR00274059-02 ARM: Add new dts for imx6q/imx6dl SabreSD hdcp
hdcp ddc pins conflict with i2c2,
add new dts file for imx6q and imx6dl SabreSD board,
enable hdcp and disable i2c2 in these dts files.
Remove hdmi pins property from mx6qdl-sabresd.dtsi.
Anson Huang [Thu, 8 Aug 2013 21:05:38 +0000 (17:05 -0400)]
ENGR00274473-1 regulator: add more notifier events
Some hardware modules need strict flows according
to regulator's enable/disable, such as for i.MX6
SOC's PU regulator, there is another power gate
in GPC module, it needs to disable PU modules' clock
before PU regulator is disabled and need to enable
clock right after PU regulator is enabled, then it
can do GPC's power gate operation.
So we need to add REGULATOR_EVENT_PRE_DISABLE and
REGULATOR_EVENT_ENABLE for regulator's notifier events.
Hongzhang Yang [Mon, 12 Aug 2013 07:38:07 +0000 (15:38 +0800)]
ENGR00274761-3 Upgrade VPU driver for Linux 3.10 kernel
Modify mxc_vpu.c to adapt to kernel 3.10 change
- Remove all references to header files in mach folder
- Include linux/clk.h instead of mach/clock.h
- Call device_reset instead of imx_src_reset_vpu
- Dummy PU and PM api callings before they are ready
- Dummy cpu_is_mx5? api callings
- Remove VM_RESERVED flags
- Call gen_pool instead of iram_alloc
Modify mxc_vpu.h
- Change CONFIG_ARCH_MX6 to CONFIG_SOC_IMX6Q
Modify Kconfig:
- Change ARCH_MX? to SOC_IMX?, remove ARCH_MX3/ARCH_MX37
because for MX3 series only SOC_IMX31 and SOC_IMX35 are
defined in Linux 3.10, and these chips don't have VPU.
Need to add SOC_IMX37 to VPU Kconfig if MX37 could be
supported later.
Add VPU to config and build path
- mxc/Kconfig
- mxc/Makefile
Signed-off-by: Hongzhang Yang <Hongzhang.Yang@freescale.com>
Hongzhang Yang [Mon, 12 Aug 2013 07:23:41 +0000 (15:23 +0800)]
ENGR00274761-2 Upgrade VPU driver for Linux 3.10 kernel
Add VPU node in dtsi
- Add VPU node (common part) in imx6qdl.dtsi. It was defined
in imx6.dtsi in Linux 3.5.7.
- Add "iram" property for gen_pool api callings
- Add "resets" property for device_reset api calling
- Add VPU node (soc specific part) in imx6q.dtsi and imx6dl.dtsi
Signed-off-by: Hongzhang Yang <Hongzhang.Yang@freescale.com>
Hongzhang Yang [Mon, 12 Aug 2013 07:14:23 +0000 (15:14 +0800)]
ENGR00274761-1 Upgrade VPU driver for Linux 3.10 kernel
Pick files from origin/imx_3.5.7 commit 135bf02a0727ea5ce96
- mxc_vpu.h is picked from arch/arm/plat-mxc/include/mach/
and put to include/linux/
- drivers/mxc/vpu/Kconfig
- drivers/mxc/vpu/Makefile
- drivers/mxc/vpu/mxc_vpu.c
Signed-off-by: Hongzhang Yang <Hongzhang.Yang@freescale.com>
Sandor Yu [Mon, 12 Aug 2013 10:51:52 +0000 (18:51 +0800)]
ENGR00274821 ARM: Add i.MX6 FB properties to dts for SabreAuto board
- Add Framebuffer and ldb properties to dts for i.MX6Q and
i.MX6DL SabreAuto board.
- Add PWM3 and backlight properties to dts for i.MX6Q and
i.Mx6DL SabreAuto board.
- fix i2c2 indent in dts.
Luwei [Thu, 8 Aug 2013 08:35:24 +0000 (16:35 +0800)]
ENGR00274247: touch: add egalax touch driver support on i.MX6Q/DL AUTO/SD
Copy the egalax touch screen driver from linux3.5.7.Make some
modification.Remove the __devinit __devexit __devexit_p out
of the file, because 3.10 does not support.
This patch removes the unnecessary gpio_set_value() and
gpio_free() function calls after request the gpios with
gpio_requestion_one() successfully. Also, this patch adds
a warning message if the request fails.
Hannstar LVDS panel CABC function turns backlight density
automatically according to display content. This may introduce
annoying unstable backlight when display content changes.
So, this patch disables the CABC function if a platform's of
device tree provides controlling gpios in lvds_cabc_ctrl node.
This patch adds lvds_cabc_ctrl node in imx6qdl-sabresd.dtsi file.
This node contains two gpio entries for the Hannstar LVDS panel
CABC control function on LVDS0 and LVDS1 interfaces.
This patch adds pinmux entries for LVDS0 and LVDS1 to control the
Hannstar LVDS panel CABC function. Pin NANDF_CS2 and pin NANDF_CS3
are configured to be gpio so that they can control the CABC function.
Anson Huang [Thu, 8 Aug 2013 17:57:23 +0000 (13:57 -0400)]
ENGR00274056-3 thermal: imx: binding device cooling to thermal
1. imx thermal depends on device cooling config, as only cpu
cooling is not enough for cooling down SOC;
2. binding device cooling to imx thermal driver.
3. add temperature buffer for passive trip, which means when
temperature cross passive trip, cooling devices will be triggered,
but only when temperature drop to more than the number we defined(10 C)
lower than passive trip, cooling devices will be canceled. this
is to avoid triggering/canceling cooling device back and forth when
temperature is around passive trip.
Anson Huang [Thu, 8 Aug 2013 17:20:40 +0000 (13:20 -0400)]
ENGR00274056-1 thermal: add device cooling for thermal driver
cpu cooling is not enough when temperature is
too hot, as some devices may contribute a lot of heat
to SOC, such as GPU, so we need to add device cooling
as well, when system is too hot, devices can also take
their actions to lower SOC temperature.
when temperature cross the passive trip, device cooling
driver will send out notification, those devices who
register this devfreq_cooling notification will take
actions to lower SOC temperature.
Robin Gong [Mon, 5 Aug 2013 09:40:02 +0000 (17:40 +0800)]
ENGR00273425 ARM: imx: enable suspend code for imx6q/dl
Enable DSM code for imx6, the code porting form kernel 3.5.7.So with the patch,
we can suspend imx6q, imx6dl from iram to decrease power number of DDR IO:
save ~15mA@1.5V on imx6qsabresd, but need more ~30us in suspend and resume back.
Liu Ying [Mon, 5 Aug 2013 07:47:22 +0000 (15:47 +0800)]
ENGR00273974-1 media: port mxc vout driver from 3.5.7 to 3.10
This is porting mxc vout driver from imx_3.5.7 kernel to
imx_3.10 kernel.
* Put the driver in drivers/media/platform/ directory instead
of drivers/media/video/ directory, since the later one is
renamed to the former one in 3.10 kernel.
* Change the ipu-v3.h header file from <mach/ipu-v3.h> to
<linux/ipu-v3.h>.
* Change the mxc_vidioc_s_crop() function's implementation since
the definition of the vidioc_s_crop() function is modified to
make the last argument be constant.
* Set vfl_dir to be VFL_DIR_TX since the ioctrl validity checks
are improved in 3.10 kernel.
* Remove 'defaut y' setting for VIDEO_MXC_OUTPUT and
VIDEO_MXC_IPU_OUTPUT Kconfigs. They may be configured by kernel
default configure or by user.
* Make VIDEO_MXC_OUTPUT Kconfig depend on FB_MXC Kconfig since
we need framebuffers to be rendered.
* Make VIDEO_MXC_IPU_OUTPUT Kconfig be tristate.
* Split <linux/mxc_v4l2.h> header file up into include/linux/
and include/uapi/linux/ directories so that the userspace may
include the mxc_v4l2.h header file.
Liu Ying [Mon, 5 Aug 2013 07:33:49 +0000 (15:33 +0800)]
ENGR00273852 ipu: header file split up
This patch splits ipu header file up to
include/linux/ directory and include/uapi/linux/
directory so that the userspace may include
the ipu header file. This patch also fixes some
annotations and macros about the header file's
naming.
Liu Ying [Thu, 1 Aug 2013 08:32:11 +0000 (16:32 +0800)]
ENGR00273500 IPUv3 dev: use wait_event_interruptible for ipu task
The ipu task thread checks outstanding tasks to be done on waiting
event uninterruptibly on the function find_task()'s return value.
However, sleeping on waiting event uninterruptibly contributes to
system load average value. This patch changes wait_event() to
wait_event_interruptible() to avoid the load average value inflation.
Fabio Estevam [Sun, 9 Jun 2013 18:17:18 +0000 (15:17 -0300)]
serial: imx: Fix serial clock unbalance
Since commit 0c375501 (serial: imx: enable the clocks for console), the
imx_startup() function calls clk_prepare_enable conditionally, so we
need to call clk_disable_unprepare inside imx_shutdown() under the same
condition to avoid unbalanced clock calls.
ENGR00240988: ARM: imx6q: add dma_zone_size for GPU limit
GPU has a limit on physical address that it accesses, which must be
below 2GiB. Since i.MX6Q/DL maps system memory at 0x10000000 (offset
256MiB), we set dma_zone_size as (SZ_2G - SZ_256M) to ensure that.
ENGR00240988: gpu: fix deprecated idr calls on 3.10 kernel
The idr calls idr_pre_get() and idr_get_new_above() are deprecated on
3.10 kernel and cause the following build issues. Replace the calls
with the new idr_alloc() to fix the issue.
CC drivers/mxc/gpu-viv/hal/os/linux/kernel/gc_hal_kernel_os.o
drivers/mxc/gpu-viv/hal/os/linux/kernel/gc_hal_kernel_os.c: In function ‘_AllocateIntegerId’:
drivers/mxc/gpu-viv/hal/os/linux/kernel/gc_hal_kernel_os.c:776:5: error: ‘idr_pre_get’ is deprecated (declared at include/linux/idr.h:151) [-Werror=deprecated-declarations]
drivers/mxc/gpu-viv/hal/os/linux/kernel/gc_hal_kernel_os.c:784:5: error: ‘idr_get_new_above’ is deprecated (declared at include/linux/idr.h:166) [-Werror=deprecated-declarations]
ENGR00240988: gpu: allocate contiguous memory from CMA for 3.10 kernel
The Contiguous Memory Allocator (CMA) is mature in 3.10 kernel. Let's
change gpu driver to allocate contiguous memory from CMA pool. Doing so
will save not only the memblock reserve calls in machine code but also
the request_mem_region() and ioremap() in gpu driver. And all the
system memory will be seen by kernel no matter whether gpu driver is
running or not.
It also changes the default contiguousSize to 128 MiB for Freescale
adjustment.
ENGR00240988: gpu: __devinit and __devexit are unavailable on 3.10 kernel
__devinit, __devexit and __devexit_p are unavailable on 3.10 kernel.
Remove them for 3.10 to fix the compile issues below.
CC drivers/mxc/gpu-viv/hal/os/linux/kernel/gc_hal_kernel_driver.o
drivers/mxc/gpu-viv/hal/os/linux/kernel/gc_hal_kernel_driver.c:1033:22: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘gpu_probe’
drivers/mxc/gpu-viv/hal/os/linux/kernel/gc_hal_kernel_driver.c:1116:22: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘gpu_remove’
drivers/mxc/gpu-viv/hal/os/linux/kernel/gc_hal_kernel_driver.c:1292:19: error: ‘gpu_probe’ undeclared here (not in a function)
drivers/mxc/gpu-viv/hal/os/linux/kernel/gc_hal_kernel_driver.c:1293:5: error: implicit declaration of function ‘__devexit_p’ [-Werror=implicit-function-declaration]
ENGR00240988: gpu: comment out busfreq calls for 3.10 kernel
The busfreq driver is not ready yet on 3.10 kernel. Let's comment out
the busfreq header inclusion and function calls for now, and revisit it
later when busfreq driver is ready.
ENGR00240988: gpu: mach/hardware.h is not available in kernel 3.10
In kernel 3.10, drivers can not include any <mach/*> headers. Do not
include <mach/hardware.h> for 3.10 kernel to fix the follow build
errors.
CC drivers/mxc/gpu-viv/hal/os/linux/kernel/gc_hal_kernel_device.o
drivers/mxc/gpu-viv/hal/os/linux/kernel/gc_hal_kernel_device.c:28:27: fatal error: mach/hardware.h: No such file or directory
CC drivers/mxc/gpu-viv/hal/os/linux/kernel/gc_hal_kernel_os.o
drivers/mxc/gpu-viv/hal/os/linux/kernel/gc_hal_kernel_os.c:33:27: fatal error: mach/hardware.h: No such file or directory
ENGR00273073-2 cpufreq: add interactive governor for cpufreq
cpufreq: interactive: New 'interactive' governor
This governor is designed for latency-sensitive workloads, such as
interactive user interfaces. The interactive governor aims to be
significantly more responsive to ramp CPU quickly up when CPU-intensive
activity begins.
Existing governors sample CPU load at a particular rate, typically
every X ms. This can lead to under-powering UI threads for the period of
time during which the user begins interacting with a previously-idle system
until the next sample period happens.
The 'interactive' governor uses a different approach. Instead of sampling
the CPU at a specified rate, the governor will check whether to scale the
CPU frequency up soon after coming out of idle. When the CPU comes out of
idle, a timer is configured to fire within 1-2 ticks. If the CPU is very
busy from exiting idle to when the timer fires then we assume the CPU is
underpowered and ramp to MAX speed.
If the CPU was not sufficiently busy to immediately ramp to MAX speed, then
the governor evaluates the CPU load since the last speed adjustment,
choosing the highest value between that longer-term load or the short-term
load since idle exit to determine the CPU speed to ramp to.
A realtime thread is used for scaling up, giving the remaining tasks the
CPU performance benefit, unlike existing governors which are more likely to
schedule rampup work to occur after your performance starved tasks have
completed.
The tuneables for this governor are:
/sys/devices/system/cpu/cpufreq/interactive/min_sample_time:
The minimum amount of time to spend at the current frequency before
ramping down. This is to ensure that the governor has seen enough
historic CPU load data to determine the appropriate workload.
/sys/devices/system/cpu/cpufreq/interactive/go_maxspeed_load
The CPU load at which to ramp to max speed.
Signed-off-by: Mike Chan <mike at android.com> Signed-off-by: Todd Poynor <toddpoynor at google.com> Signed-off-by: Allen Martin <amartin at nvidia.com> (submitted improvements) Signed-off-by: Axel Haslam <axelhaslam at ti.com> (submitted improvements) Signed-off-by: Anton Vorontsov <anton.vorontsov at linaro.org> Signed-off-by: Anson Huang <b20788@freescale.com>
ENGR00240987: ipu: port ipuv3 driver from 3.5.7 kernel
This is a fast-forward porting of ipuv3 driver from 3.5.7 kernel to
kernel 3.10. The change set is kept as minimum as possible with only
making necessary code changes to adapt 3.10 kernel internal API and
framework updates. Everything else should be same as 3.5.7 one. The
change set consists of the following.
* Remove unused Kconfig options MXC_IPU_V3D, MXC_IPU_V3EX and
MXC_IPU_V3H
* Comment out busfreq calls
* Move ipu-v3.h into include/linux/, and remove all <mach/*> includes
* Drop __devinit and __devexit
* Remove assignment of pltfm_data->pg = imx6q_ipu_pg;
* Use generic device_reset() API rather than ipu_pltfm_data->init()
hook to reset IPU
* Includes <linux/sched/rt.h> ipu_device.c to fix undeclared
MAX_USER_RT_PRIO error
* Change compatible string to "fsl,imx6q-ipu" to align with community
kernel
* Define irq_sync before irq_err in DTS to align with community kernel
* Drop "ipu1_" and "ipu2_" from clock names to save the handling of the
second parameter of devm_clk_get()
* Remove the buggy csi_clk setup in ipu_clk_setup_enable() and validate
the clock before operate on it in ipu_csi_enable_mclk()
* Replace iram API (linux/iram_alloc.h) with generic memory pool API
(linux/genalloc.h) in VDOA driver
ARM: dts: imx: ocram size is different between imx6q and imx6dl
The ocram on imx6q is 256 KiB while on imx6dl it's 128 KiB. Let's
have separate node for imx6q and imx6dl. It also changes imx6q size
0x3f000 to 0x40000 to match the hardware.
ENGR00269945: pinctrl: support pinctrl setting assertion via gpios
It's pretty common that on some reference design or validation boards,
one pin could be used by two devices on board, and the pin route is
controlled by a GPIO. So to assert the pin for given device, not only
the pinmux controller in SoC needs to be set up properly but also the
GPIO needs to be pulled up/down.
The patch adds support of a device tree property "pinctrl-assert-gpios"
under client device node. It plays pretty much like a board level pin
multiplexer, and steers the pin route by controlling the GPIOs. When
client device has the property represent in its node, pinctrl device
tree mapping function will firstly pull up/down the GPIOs to assert the
pins for the device at board level.
1) Fix checksumming regressions, from Tom Herbert.
2) Undo unintentional permissions changes for SCTP rto_alpha and
rto_beta sysfs knobs, from Denial Borkmann.
3) VXLAN, like other IP tunnels, should advertize it's encapsulation
size using dev->needed_headroom instead of dev->hard_header_len.
From Cong Wang.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
net: sctp: fix permissions for rto_alpha and rto_beta knobs
vxlan: Checksum fixes
net: add skb_pop_rcv_encapsulation
udp: call __skb_checksum_complete when doing full checksum
net: Fix save software checksum complete
net: Fix GSO constants to match NETIF flags
udp: ipv4: do not waste time in __udp4_lib_mcast_demux_lookup
vxlan: use dev->needed_headroom instead of dev->hard_header_len
MAINTAINERS: update cxgb4 maintainer
Linus Torvalds [Mon, 16 Jun 2014 02:02:20 +0000 (16:02 -1000)]
Merge tag 'clk-for-linus-3.16-part2' of git://git.linaro.org/people/mike.turquette/linux
Pull more clock framework updates from Mike Turquette:
"This contains the second half the of the clk changes for 3.16.
They are simply fixes and code refactoring for the OMAP clock drivers.
The sunxi clock driver changes include splitting out the one
mega-driver into several smaller pieces and adding support for the A31
SoC clocks"
* tag 'clk-for-linus-3.16-part2' of git://git.linaro.org/people/mike.turquette/linux: (25 commits)
clk: sunxi: document PRCM clock compatible strings
clk: sunxi: add PRCM (Power/Reset/Clock Management) clks support
clk: sun6i: Protect SDRAM gating bit
clk: sun6i: Protect CPU clock
clk: sunxi: Rework clock protection code
clk: sunxi: Move the GMAC clock to a file of its own
clk: sunxi: Move the 24M oscillator to a file of its own
clk: sunxi: Remove calls to clk_put
clk: sunxi: document new A31 USB clock compatible
clk: sunxi: Implement A31 USB clock
ARM: dts: OMAP5/DRA7: use omap5-mpu-dpll-clock capable of dealing with higher frequencies
CLK: TI: dpll: support OMAP5 MPU DPLL that need special handling for higher frequencies
ARM: OMAP5+: dpll: support Duty Cycle Correction(DCC)
CLK: TI: clk-54xx: Set the rate for dpll_abe_m2x2_ck
CLK: TI: Driver for DRA7 ATL (Audio Tracking Logic)
dt:/bindings: DRA7 ATL (Audio Tracking Logic) clock bindings
ARM: dts: dra7xx-clocks: Correct name for atl clkin3 clock
CLK: TI: gate: add composite interface clock to OMAP2 only build
ARM: OMAP2: clock: add DT boot support for cpufreq_ck
CLK: TI: OMAP2: add clock init support
...
Pull NVMe update from Matthew Wilcox:
"Mostly bugfixes again for the NVMe driver. I'd like to call out the
exported tracepoint in the block layer; I believe Keith has cleared
this with Jens.
We've had a few reports from people who're really pounding on NVMe
devices at scale, hence the timeout changes (and new module
parameters), hotplug cpu deadlock, tracepoints, and minor performance
tweaks"
[ Jens hadn't seen that tracepoint thing, but is ok with it - it will
end up going away when mq conversion happens ]
* git://git.infradead.org/users/willy/linux-nvme: (22 commits)
NVMe: Fix START_STOP_UNIT Scsi->NVMe translation.
NVMe: Use Log Page constants in SCSI emulation
NVMe: Define Log Page constants
NVMe: Fix hot cpu notification dead lock
NVMe: Rename io_timeout to nvme_io_timeout
NVMe: Use last bytes of f/w rev SCSI Inquiry
NVMe: Adhere to request queue block accounting enable/disable
NVMe: Fix nvme get/put queue semantics
NVMe: Delete NVME_GET_FEAT_TEMP_THRESH
NVMe: Make admin timeout a module parameter
NVMe: Make iod bio timeout a parameter
NVMe: Prevent possible NULL pointer dereference
NVMe: Fix the buffer size passed in GetLogPage(CDW10.NUMD)
NVMe: Update data structures for NVMe 1.2
NVMe: Enable BUILD_BUG_ON checks
NVMe: Update namespace and controller identify structures to the 1.1a spec
NVMe: Flush with data support
NVMe: Configure support for block flush
NVMe: Add tracepoints
NVMe: Protect against badly formatted CQEs
...
Daniel Borkmann [Sat, 14 Jun 2014 22:59:14 +0000 (00:59 +0200)]
net: sctp: fix permissions for rto_alpha and rto_beta knobs
Commit 3fd091e73b81 ("[SCTP]: Remove multiple levels of msecs
to jiffies conversions.") has silently changed permissions for
rto_alpha and rto_beta knobs from 0644 to 0444. The purpose of
this was to discourage users from tweaking rto_alpha and
rto_beta knobs in production environments since they are key
to correctly compute rtt/srtt.
RFC4960 under section 6.3.1. RTO Calculation says regarding
rto_alpha and rto_beta under rule C3 and C4:
[...]
C3) When a new RTT measurement R' is made, set
Note: The value of SRTT used in the update to RTTVAR
is its value before updating SRTT itself using the
second assignment. After the computation, update
RTO <- SRTT + 4 * RTTVAR.
C4) When data is in flight and when allowed by rule C5
below, a new RTT measurement MUST be made each round
trip. Furthermore, new RTT measurements SHOULD be
made no more than once per round trip for a given
destination transport address. There are two reasons
for this recommendation: First, it appears that
measuring more frequently often does not in practice
yield any significant benefit [ALLMAN99]; second,
if measurements are made more often, then the values
of RTO.Alpha and RTO.Beta in rule C3 above should be
adjusted so that SRTT and RTTVAR still adjust to
changes at roughly the same rate (in terms of how many
round trips it takes them to reflect new values) as
they would if making only one measurement per
round-trip and using RTO.Alpha and RTO.Beta as given
in rule C3. However, the exact nature of these
adjustments remains a research issue.
[...]
While it is discouraged to adjust rto_alpha and rto_beta
and not further specified how to adjust them, the RFC also
doesn't explicitly forbid it, but rather gives a RECOMMENDED
default value (rto_alpha=3, rto_beta=2). We have a couple
of users relying on the old permissions before they got
changed. That said, if someone really has the urge to adjust
them, we could allow it with a warning in the log.
Fixes: 3fd091e73b81 ("[SCTP]: Remove multiple levels of msecs to jiffies conversions.") Signed-off-by: Daniel Borkmann <dborkman@redhat.com> Cc: Vlad Yasevich <vyasevich@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 15 Jun 2014 08:00:56 +0000 (01:00 -0700)]
Merge branch 'csum_fixes'
Tom Herbert says:
====================
Fixes related to some recent checksum modifications.
- Fix GSO constants to match NETIF flags
- Fix logic in saving checksum complete in __skb_checksum_complete
- Call __skb_checksum_complete from UDP if we are checksumming over
whole packet in order to save checksum.
- Fixes to VXLAN to work correctly with checksum complete
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert [Sun, 15 Jun 2014 06:24:28 +0000 (23:24 -0700)]
net: add skb_pop_rcv_encapsulation
This function is used by UDP encapsulation protocols in RX when
crossing encapsulation boundary. If ip_summed is set to
CHECKSUM_UNNECESSARY and encapsulation is not set, change to
CHECKSUM_NONE since the checksum has not been validated within the
encapsulation. Clears csum_valid by the same rationale.
Signed-off-by: Tom Herbert <therbert@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert [Sun, 15 Jun 2014 06:24:20 +0000 (23:24 -0700)]
udp: call __skb_checksum_complete when doing full checksum
In __udp_lib_checksum_complete check if checksum is being done over all
the data (len is equal to skb->len) and if it is call
__skb_checksum_complete instead of __skb_checksum_complete_head. This
allows checksum to be saved in checksum complete.
Signed-off-by: Tom Herbert <therbert@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert [Sun, 15 Jun 2014 06:24:03 +0000 (23:24 -0700)]
net: Fix save software checksum complete
Geert reported issues regarding checksum complete and UDP.
The logic introduced in commit 7e3cead5172927732f51fde
("net: Save software checksum complete") is not correct.
This patch:
1) Restores code in __skb_checksum_complete_header except for setting
CHECKSUM_UNNECESSARY. This function may be calculating checksum on
something less than skb->len.
2) Adds saving checksum to __skb_checksum_complete. The full packet
checksum 0..skb->len is calculated without adding in pseudo header.
This value is saved in skb->csum and then the pseudo header is added
to that to derive the checksum for validation.
3) In both __skb_checksum_complete_header and __skb_checksum_complete,
set skb->csum_valid to whether checksum of zero was computed. This
allows skb_csum_unnecessary to return true without changing to
CHECKSUM_UNNECESSARY which was done previously.
4) Copy new csum related bits in __copy_skb_header.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Tom Herbert <therbert@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert [Sun, 15 Jun 2014 06:23:52 +0000 (23:23 -0700)]
net: Fix GSO constants to match NETIF flags
Joseph Gasparakis reported that VXLAN GSO offload stopped working with
i40e device after recent UDP changes. The problem is that the
SKB_GSO_* bits are out of sync with the corresponding NETIF flags. This
patch fixes that. Also, we add BUILD_BUG_ONs in net_gso_ok for several
GSO constants that were missing to avoid the problem in the future.
Reported-by: Joseph Gasparakis <joseph.gasparakis@intel.com> Signed-off-by: Tom Herbert <therbert@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sun, 15 Jun 2014 00:49:48 +0000 (19:49 -0500)]
Merge tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull more SCSI updates from James Bottomley:
"This is just a couple of drivers (hpsa and lpfc) that got left out for
further testing in linux-next. We also have one fix to a prior
submission (qla2xxx sparse)"
* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (36 commits)
qla2xxx: fix sparse warnings introduced by previous target mode t10-dif patch
lpfc: Update lpfc version to driver version 10.2.8001.0
lpfc: Fix ExpressLane priority setup
lpfc: mark old devices as obsolete
lpfc: Fix for initializing RRQ bitmap
lpfc: Fix for cleaning up stale ring flag and sp_queue_event entries
lpfc: Update lpfc version to driver version 10.2.8000.0
lpfc: Update Copyright on changed files from 8.3.45 patches
lpfc: Update Copyright on changed files
lpfc: Fixed locking for scsi task management commands
lpfc: Convert runtime references to old xlane cfg param to fof cfg param
lpfc: Fix FW dump using sysfs
lpfc: Fix SLI4 s abort loop to process all FCP rings and under ring_lock
lpfc: Fixed kernel panic in lpfc_abort_handler
lpfc: Fix locking for postbufq when freeing
lpfc: Fix locking for lpfc_hba_down_post
lpfc: Fix dynamic transitions of FirstBurst from on to off
hpsa: fix handling of hpsa_volume_offline return value
hpsa: return -ENOMEM not -1 on kzalloc failure in hpsa_get_device_id
hpsa: remove messages about volume status VPD inquiry page not supported
...
Linus Torvalds [Sun, 15 Jun 2014 00:48:43 +0000 (19:48 -0500)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull more btrfs updates from Chris Mason:
"This has a few fixes since our last pull and a new ioctl for doing
btree searches from userland. It's very similar to the existing
ioctl, but lets us return larger items back down to the app"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
btrfs: fix error handling in create_pending_snapshot
btrfs: fix use of uninit "ret" in end_extent_writepage()
btrfs: free ulist in qgroup_shared_accounting() error path
Btrfs: fix qgroups sanity test crash or hang
btrfs: prevent RCU warning when dereferencing radix tree slot
Btrfs: fix unfinished readahead thread for raid5/6 degraded mounting
btrfs: new ioctl TREE_SEARCH_V2
btrfs: tree_search, search_ioctl: direct copy to userspace
btrfs: new function read_extent_buffer_to_user
btrfs: tree_search, copy_to_sk: return needed size on EOVERFLOW
btrfs: tree_search, copy_to_sk: return EOVERFLOW for too small buffer
btrfs: tree_search, search_ioctl: accept varying buffer
btrfs: tree_search: eliminate redundant nr_items check
Al Viro [Sat, 14 Jun 2014 06:12:41 +0000 (07:12 +0100)]
fix __swap_writepage() compile failure on old gcc versions
Tetsuo Handa wrote:
"Commit 62a8067a7f35 ("bio_vec-backed iov_iter") introduced an unnamed
union inside a struct which gcc-4.4.7 cannot handle. Name the unnamed
union as u in order to fix build failure"
Let's do this instead: there is only one place in the entire tree that
steps into this breakage. Anon structs and unions work in older gcc
versions; as the matter of fact, we have those in the tree - see e.g.
struct ieee80211_tx_info in include/net/mac80211.h
What doesn't work is handling their initializers:
struct {
int a;
union {
int b;
char c;
};
} x[2] = {{.a = 1, .c = 'a'}, {.a = 0, .b = 1}};
is the obvious syntax for initializer, perfectly fine for C11 and
handled correctly by gcc-4.7 or later.
Earlier versions, though, break on it - declaration is fine and so's
access to fields (i.e. x[0].c = 'a'; would produce the right code), but
members of the anon structs and unions are not inserted into the right
namespace. Tellingly, those older versions will not barf on struct {int
a; struct {int a;};}; - looks like they just have it hacked up somewhere
around the handling of . and -> instead of doing the right thing.
The easiest way to deal with that crap is to turn initialization of
those fields (in the only place where we have such initializer of
iov_iter) into plain assignment.
Reported-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Reported-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sat, 14 Jun 2014 21:51:25 +0000 (14:51 -0700)]
Merge tag 'hsi-for-3.16-fixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-hsi
Pull HSI build fixes from Sebastian Reichel:
- tighten dependency between ssi-protocol and omap-ssi to fix build
failures with randconfig.
- use normal module refcounting in omap driver to fix build with
disabled module support
* tag 'hsi-for-3.16-fixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-hsi:
hsi: omap_ssi_port: use normal module refcounting
HSI: fix omap ssi driver dependency
Linus Torvalds [Sat, 14 Jun 2014 21:46:29 +0000 (14:46 -0700)]
Merge branch 'x86-vdso-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 vdso fixes from Peter Anvin:
"Fixes for x86/vdso.
One is a simple build fix for bigendian hosts, one is to make "make
vdso_install" work again, and the rest is about working around a bug
in Google's Go language -- two are documentation patches that improves
the sample code that the Go coders took, modified, and broke; the
other two implements a workaround that keeps existing Go binaries from
segfaulting at least"
* 'x86-vdso-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/vdso: Fix vdso_install
x86/vdso: Hack to keep 64-bit Go programs working
x86/vdso: Add PUT_LE to store little-endian values
x86/vdso/doc: Make vDSO examples more portable
x86/vdso/doc: Rename vdso_test.c to vdso_standalone_test_x86.c
x86, vdso: Remove one final use of htole16()
Linus Torvalds [Sat, 14 Jun 2014 21:43:23 +0000 (14:43 -0700)]
Merge tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
- new driver for Sensirion SHTC1 humidity / temperature sensor
- convert ltc4151 and vexpress drivers to use devm functions
- drop generic chip detection from lm85 driver
- avoid forward declarations in atxp1 driver
- fix sign extensions in ina2xx driver
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: vexpress: Use devm helper for hwmon device registration
hwmon: (atxp1) Avoid forward declaration
hwmon: add support for Sensirion SHTC1 sensor
hwmon: (ltc4151) Convert to devm_hwmon_device_register_with_groups
hwmon: (lm85) Drop generic detection
hwmon: (ina2xx) Cast to s16 on shunt and current regs
Eric Dumazet [Thu, 12 Jun 2014 23:13:06 +0000 (16:13 -0700)]
udp: ipv4: do not waste time in __udp4_lib_mcast_demux_lookup
Its too easy to add thousand of UDP sockets on a particular bucket,
and slow down an innocent multicast receiver.
Early demux is supposed to be an optimization, we should avoid spending
too much time in it.
It is interesting to note __udp4_lib_demux_lookup() only tries to
match first socket in the chain.
10 is the threshold we already have in __udp4_lib_lookup() to switch
to secondary hash.
Fixes: 421b3885bf6d5 ("udp: ipv4: Add udp early demux") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: David Held <drheld@google.com> Cc: Shawn Bohrer <sbohrer@rgmadvisors.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Cong Wang [Thu, 12 Jun 2014 18:53:10 +0000 (11:53 -0700)]
vxlan: use dev->needed_headroom instead of dev->hard_header_len
When we mirror packets from a vxlan tunnel to other device,
the mirror device should see the same packets (that is, without
outer header). Because vxlan tunnel sets dev->hard_header_len,
tcf_mirred() resets mac header back to outer mac, the mirror device
actually sees packets with outer headers
Vxlan tunnel should set dev->needed_headroom instead of
dev->hard_header_len, like what other ip tunnels do. This fixes
the above problem.
Cc: "David S. Miller" <davem@davemloft.net> Cc: stephen hemminger <stephen@networkplumber.org> Cc: Pravin B Shelar <pshelar@nicira.com> Signed-off-by: Cong Wang <cwang@twopensource.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Andy Lutomirski [Thu, 12 Jun 2014 15:28:10 +0000 (08:28 -0700)]
x86/vdso: Fix vdso_install
"make vdso_install" installs unstripped versions of the vdso objects
for the benefit of the debugger. This was broken by checkin:
6f121e548f83 x86, vdso: Reimplement vdso.so preparation in build-time C
The filenames are different now, so update the Makefile to cope.
This still installs the 64-bit vdso as vdso64.so. We believe this
will be okay, as the only known user is a patched gdb which is known
to use build-ids, but if it turns out to be a problem we may have to
add a link.
Dan McLeran [Fri, 6 Jun 2014 14:27:27 +0000 (08:27 -0600)]
NVMe: Fix START_STOP_UNIT Scsi->NVMe translation.
This patch contains several fixes for Scsi START_STOP_UNIT. The previous
code did not account for signed vs. unsigned arithmetic which resulted
in an invalid lowest power state caculation when the device only supports
1 power state.
The code for Power Condition == 2 (Idle) was not following the spec. The
spec calls for setting the device to specific power states, depending
upon Power Condition Modifier, without accounting for the number of
power states supported by the device.
The code for Power Condition == 3 (Standby) was using a hard-coded '0'
which is replaced with the macro POWER_STATE_0.
Signed-off-by: Dan McLeran <daniel.mcleran@intel.com> Reviewed-by: Vishal Verma <vishal.l.verma@linux.intel.com> Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>