Bjørn Mork [Thu, 3 Mar 2016 21:20:53 +0000 (22:20 +0100)]
cdc_ncm: toggle altsetting to force reset before setup
Some devices will silently fail setup unless they are reset first.
This is necessary even if the data interface is already in
altsetting 0, which it will be when the device is probed for the
first time. Briefly toggling the altsetting forces a function
reset regardless of the initial state.
This fixes a setup problem observed on a number of Huawei devices,
appearing to operate in NTB-32 mode even if we explicitly set them
to NTB-16 mode.
Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
Oliver Neukum [Mon, 7 Mar 2016 10:31:10 +0000 (11:31 +0100)]
usbnet: cleanup after bind() in probe()
In case bind() works, but a later error forces bailing
in probe() in error cases work and a timer may be scheduled.
They must be killed. This fixes an error case related to
the double free reported in
http://www.spinics.net/lists/netdev/msg367669.html
and needs to go on top of Linus' fix to cdc-ncm.
Signed-off-by: Oliver Neukum <ONeukum@suse.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Mon, 7 Mar 2016 14:15:30 +0000 (15:15 +0100)]
mlxsw: pci: Correctly determine if descriptor queue is full
The descriptor queues for sending (SDQs) and receiving (RDQs) packets
are managed by two counters - producer and consumer - which are both
16-bit in size. A queue is considered full when the difference between
the two equals the queue's maximum number of descriptors.
However, if the producer counter overflows, then it's possible for the
full queue check to fail, as it doesn't take the overflow into account.
In such a case, descriptors already passed to the device - but for which
a completion has yet to be posted - will be overwritten, thereby causing
undefined behavior. The above can be achieved under heavy load (~30
netperf instances).
Fix that by casting the subtraction result to u16, preventing it from
being treated as a signed integer.
Fixes: eda6500a987a ("mlxsw: Add PCI bus implementation") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Since we only support one VLAN filtering bridge we need to associate a
reference count with it, so that when the last port netdev leaves it, we
would know that a different bridge can be offloaded to hardware.
When a LAG device is memeber in a bridge and port netdevs are leaving
the LAG, we should always decrement the bridge's reference count, as it's
incremented for any port in the LAG.
Fixes: 4dc236c31733 ("mlxsw: spectrum: Handle port leaving LAG while bridged") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
tipc: fix nullptr crash during subscription cancel
commit 4d5cfcba2f6e ('tipc: fix connection abort during subscription
cancel'), removes the check for a valid subscription before calling
tipc_nametbl_subscribe().
This will lead to a nullptr exception when we process a
subscription cancel request. For a cancel request, a null
subscription is passed to tipc_nametbl_subscribe() resulting
in exception.
In this commit, we call tipc_nametbl_subscribe() only for
a valid subscription.
Fixes: 4d5cfcba2f6e ('tipc: fix connection abort during subscription cancel') Reported-by: Anders Widell <anders.widell@ericsson.com> Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com> Acked-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Ian King [Thu, 3 Mar 2016 13:47:18 +0000 (13:47 +0000)]
net: eth: altera: do not free array priv->mdio->irq
priv->mdio->irq used to be allocated and required freeing, but it
is now a fixed sized array and should no longer be free'd.
Issue detected using static analysis with CoverityScan
Fixes: e7f4dc3536a400 ("mdio: Move allocation of interrupts into core") Signed-off-by: Colin Ian King <colin.king@canonical.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Ian King [Thu, 3 Mar 2016 13:43:34 +0000 (13:43 +0000)]
net/ethoc: do not free array priv->mdio->irq
priv->mdio->irq used to be allocated and required freeing, but it
is now a fixed sized array and should no longer be free'd.
Issue detected using static analysis with CoverityScan
Fixes: e7f4dc3536a400 ("mdio: Move allocation of interrupts into core") Signed-off-by: Colin Ian King <colin.king@canonical.com> Reviewed-by: Tobias Klauser <tklauser@distanz.ch> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Phil Sutter [Thu, 3 Mar 2016 13:34:14 +0000 (14:34 +0100)]
net: sched: fix act_ipt for LOG target
Before calling the destroy() or target() callbacks, the family parameter
field has to be initialized. Otherwise at least the LOG target will
refuse to work and upon removal oops the kernel.
Cc: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: Phil Sutter <phil@nwl.cc> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Ian King [Thu, 3 Mar 2016 13:27:56 +0000 (13:27 +0000)]
asix: do not free array priv->mdio->irq
Used to be allocated and required freeing, but now
priv->mdio->irq is now a fixed sized array and should no longer be
free'd.
Issue detected using static analysis with CoverityScan
Fixes: e7f4dc3536a400 ("mdio: Move allocation of interrupts into core") Signed-off-by: Colin Ian King <colin.king@canonical.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Atsushi Nemoto [Thu, 3 Mar 2016 00:07:51 +0000 (09:07 +0900)]
gianfar: Enable eTSEC-106 erratum w/a for MPC8548E Rev2
Enable workaround for MPC8548E erratum eTSEC 106,
"Excess delays when transmitting TOE=1 large frames".
(see commit 53fad77375ce "gianfar: Enable eTSEC-20 erratum w/a
for P2020 Rev1")
This erratum was fixed in Rev 3.1.x.
Signed-off-by: Atsushi Nemoto <nemoto@toshiba-tops.co.jp> Acked-by: Claudiu Manoil <claudiu.manoil@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 4 Mar 2016 19:32:47 +0000 (14:32 -0500)]
Merge tag 'linux-can-fixes-for-4.5-20160304' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2016-03-04
this is a pull request for net/master.
There is one patch from Ed Spiridonov, which increases the performance of the
mcp251x SPI CAN driver, by avoiding to write to error flag register if it's
unnecessary.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Venkat Duvvuru [Wed, 2 Mar 2016 11:00:28 +0000 (06:00 -0500)]
be2net: don't enable multicast flag in be_enable_if_filters() routine
When the interface is opened (in be_open()) the routine
be_enable_if_filters() must be called to switch on the basic filtering
capabilities of an interface that are not changed at run-time.
These include the flags UNTAGGED, BROADCAST and PASS_L3L4_ERRORS.
Other flags such as MULTICAST and PROMISC must be enabled later by
be_set_rx_mode() based on the state in the netdev/adapter struct.
be_enable_if_filters() routine is wrongly trying to enable MULTICAST flag
without checking the current adapter state. This can cause the RX_FILTER
cmds to the FW to fail. This patch fixes this problem by only enabling
the basic filtering flags in be_enable_if_filters().
The VF must be able to issue RX_FILTER cmd with any filter flag, as long
as the PF allowed those flags (if_cap_flags) in the iface it provisioned
for the VF. This rule is applicable even when the VF doesn't have the
FILTMGMT privilege. There is a bug in BE3 FW that wrongly fails RX_FILTER
multicast programming cmds on VFs that don't have FILTMGMT privilege.
This patch also helps in insulating the VF driver from be_open failures due
to the FW bug. A fix for the BE3 FW issue will be available in
versions >= 11.0.283.0 and 10.6.334.0
Reported-by: Ivan Vecera <ivecera@redhat.com> Signed-off-by: Venkat Duvvuru <venkatkumar.duvvuru@avagotech.com> Signed-off-by: Sathya Perla <sathya.perla@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Wed, 2 Mar 2016 10:11:10 +0000 (13:11 +0300)]
net: moxa: fix an error code
We accidentally return IS_ERR(priv->base) which is 1 instead of
PTR_ERR(priv->base) which is the error code.
Fixes: 6c821bd9edc9 ('net: Add MOXA ART SoCs ethernet driver') Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Wed, 2 Mar 2016 01:32:08 +0000 (02:32 +0100)]
vxlan: fix missing options_len update on RX with collect metadata
When signalling to metadata consumers that the metadata_dst entry
carries additional GBP extension data for vxlan (TUNNEL_VXLAN_OPT),
the dst's vxlan_metadata information is populated, but options_len
is left to zero. F.e. in ovs, ovs_flow_key_extract() checks for
options_len before extracting the data through ip_tunnel_info_opts_get().
Geneve uses ip_tunnel_info_opts_set() helper in receive path, which
sets options_len internally, vxlan however uses ip_tunnel_info_opts(),
so when filling vxlan_metadata, we do need to update options_len.
Fixes: 4c22279848c5 ("ip-tunnel: Use API to access tunnel metadata options.") Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Thomas Graf <tgraf@suug.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Wolfram Sang [Tue, 1 Mar 2016 16:37:59 +0000 (17:37 +0100)]
net: ethernet: renesas: sh_eth: don't open code of_device_get_match_data()
This change will also make Coverity happy by avoiding a theoretical NULL
pointer dereference; yet another reason is to use the above helper function
to tighten the code and make it more readable.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Simon Horman <horms+renesas@verge.net.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Wolfram Sang [Tue, 1 Mar 2016 16:37:58 +0000 (17:37 +0100)]
net: ethernet: renesas: ravb_main: don't open code of_device_get_match_data()
This change will also make Coverity happy by avoiding a theoretical NULL
pointer dereference; yet another reason is to use the above helper function
to tighten the code and make it more readable.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Simon Horman <horms+renesas@verge.net.au> Acked-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas Falcon [Tue, 1 Mar 2016 16:20:09 +0000 (10:20 -0600)]
ibmvnic: Fix ibmvnic_capability struct
The ibmvnic_capability struct was defined incorrectly. The last two
elements of the struct are in the wrong order. In addition, the number
element should be 64-bit. Byteswapping functions are updated
as well.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
ipv6: re-enable fragment header matching in ipv6_find_hdr
When ipv6_find_hdr is used to find a fragment header
(caller specifies target NEXTHDR_FRAGMENT) we erronously return
-ENOENT for all fragments with nonzero offset.
Before commit 9195bb8e381d, when target was specified, we did not
enter the exthdr walk loop as nexthdr == target so this used to work.
Now we do (so we can skip empty route headers). When we then stumble upon
a frag with nonzero frag_off we must return -ENOENT ("header not found")
only if the caller did not specifically request NEXTHDR_FRAGMENT.
This allows nfables exthdr expression to match ipv6 fragments, e.g. via
nft add rule ip6 filter input frag frag-off gt 0
Fixes: 9195bb8e381d ("ipv6: improve ipv6_find_hdr() to skip empty routing headers") Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: David S. Miller <davem@davemloft.net>
tipc: Revert "tipc: use existing sk_write_queue for outgoing packet chain"
reverts commit 94153e36e709e ("tipc: use existing sk_write_queue for
outgoing packet chain")
In Commit 94153e36e709e, we assume that we fill & empty the socket's
sk_write_queue within the same lock_sock() session.
This is not true if the link is congested. During congestion, the
socket lock is released while we wait for the congestion to cease.
This implementation causes a nullptr exception, if the user space
program has several threads accessing the same socket descriptor.
Consider two threads of the same program performing the following:
Thread1 Thread2
-------------------- ----------------------
Enter tipc_sendmsg() Enter tipc_sendmsg()
lock_sock() lock_sock()
Enter tipc_link_xmit(), ret=ELINKCONG spin on socket lock..
sk_wait_event() :
release_sock() grab socket lock
: Enter tipc_link_xmit(), ret=0
: release_sock()
Wakeup after congestion
lock_sock()
skb = skb_peek(pktchain);
!! TIPC_SKB_CB(skb)->wakeup_pending = tsk->link_cong;
In this case, the second thread transmits the buffers belonging to
both thread1 and thread2 successfully. When the first thread wakeup
after the congestion it assumes that the pktchain is intact and
operates on the skb's in it, which leads to the following exception:
In this commit, we maintain the skb list always in the stack.
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com> Acked-by: Ying Xue <ying.xue@windriver.com> Acked-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Benjamin Poirier [Mon, 29 Feb 2016 23:03:33 +0000 (15:03 -0800)]
mld, igmp: Fix reserved tailroom calculation
The current reserved_tailroom calculation fails to take hlen and tlen into
account.
skb:
[__hlen__|__data____________|__tlen___|__extra__]
^ ^
head skb_end_offset
In this representation, hlen + data + tlen is the size passed to alloc_skb.
"extra" is the extra space made available in __alloc_skb because of
rounding up by kmalloc. We can reorder the representation like so:
[__hlen__|__data____________|__extra__|__tlen___]
^ ^
head skb_end_offset
The maximum space available for ip headers and payload without
fragmentation is min(mtu, data + extra). Therefore,
reserved_tailroom
= data + extra + tlen - min(mtu, data + extra)
= skb_end_offset - hlen - min(mtu, skb_end_offset - hlen - tlen)
= skb_tailroom - min(mtu, skb_tailroom - tlen) ; after skb_reserve(hlen)
Compare the second line to the current expression:
reserved_tailroom = skb_end_offset - min(mtu, skb_end_offset)
and we can see that hlen and tlen are not taken into account.
The min() in the third line can be expanded into:
if mtu < skb_tailroom - tlen:
reserved_tailroom = skb_tailroom - mtu
else:
reserved_tailroom = tlen
Depending on hlen, tlen, mtu and the number of multicast address records,
the current code may output skbs that have less tailroom than
dev->needed_tailroom or it may output more skbs than needed because not all
space available is used.
Fixes: 4c672e4b ("ipv6: mld: fix add_grhead skb_over_panic for devs with large MTUs") Signed-off-by: Benjamin Poirier <bpoirier@suse.com> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch manages the case when you have an Ethernet MAC with
a "fixed link", and not connected to a normal MDIO-managed PHY device.
The test of phy_bus_name was not helpful because it was never affected
and replaced by the mdio test node.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org> Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 2 Mar 2016 19:57:16 +0000 (14:57 -0500)]
Merge branch 'dwc_eth_qos'
Lars Persson says:
====================
dwc_eth_qos: stability fixes and support for CMA
This series has bug fixes for the dwc_eth_qos ethernet driver.
Mainly two stability fixes for problems found by Rabin Vincent:
- Successive starts and stops of the interface would trigger a DMA reset timeout.
- A race condition in the TX DMA handling could trigger a netdev watchdog
timeout.
The memory allocation was improved to support use of the CMA as DMA allocator
backend.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Rabin Vincent [Mon, 29 Feb 2016 15:22:33 +0000 (16:22 +0100)]
dwc_eth_qos: use DWCEQOS_MSG_DEFAULT
Since debug is hardcoded to 3, the defaults in the DWCEQOS_MSG_DEFAULT
macro are never used, which does not seem to be the intended behaviour
here. Set debug to -1 like other drivers so that DWCEQOS_MSG_DEFAULT is
actually used by default.
Signed-off-by: Rabin Vincent <rabinv@axis.com> Signed-off-by: Lars Persson <larper@axis.com> Signed-off-by: David S. Miller <davem@davemloft.net>
To prepare for using the CMA, we can not be in atomic context when
de-allocating DMA buffers.
The tx lock was needed only to protect the hw reset against the xmit
handler. Now we briefly grab the tx lock while stopping the queue to
make sure no thread is inside or will enter the xmit handler.
Signed-off-by: Lars Persson <larper@axis.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Rabin Vincent [Mon, 29 Feb 2016 15:22:30 +0000 (16:22 +0100)]
dwc_eth_qos: fix race condition in dwceqos_start_xmit
The xmit handler and the tx_reclaim tasklet had a race on the tx_free
variable which could lead to a tx timeout if tx_free was updated after
the tx complete interrupt.
Signed-off-by: Rabin Vincent <rabinv@axis.com> Signed-off-by: Lars Persson <larper@axis.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 2 Mar 2016 19:42:46 +0000 (14:42 -0500)]
Merge branch 'mlx4-fixes'
Or Gerlitz says:
====================
Mellanox 10/40G mlx4 driver fixes for 4.5-rc6
This series contains two fixes for the SRIOV HW LAG that was
introduced in 4.5-rc1 and one fix that allows to revoke the
administrative MAC that was assigned to VF through the PF.
The VF mac fix needs to go for stable too.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
net/mlx4_core: Allow resetting VF admin mac to zero
The VF administrative mac addresses (stored in the PF driver) are
initialized to zero when the PF driver starts up.
These addresses may be modified in the PF driver through ndo calls
initiated by iproute2 or libvirt.
While we allow the PF/host to change the VF admin mac address from zero
to a valid unicast mac, we do not allow restoring the VF admin mac to
zero. We currently only allow changing this mac to a different unicast mac.
This leads to problems when libvirt scripts are used to deal with
VF mac addresses, and libvirt attempts to revoke the mac so this
host will not use it anymore.
Fix this by allowing resetting a VF administrative MAC back to zero.
Fixes: 8f7ba3ca12f6 ('net/mlx4: Add set VF mac address support') Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Reported-by: Moshe Levi <moshele@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Moni Shoua [Wed, 2 Mar 2016 15:47:45 +0000 (17:47 +0200)]
net/mlx4_core: Check the correct limitation on VFs for HA mode
The limit of 63 is only for virtual functions while the actual enforcement
was for VFs plus physical functions, fix that.
Fixes: e57968a10bc1 ('net/mlx4_core: Support the HA mode for SRIOV VFs too') Signed-off-by: Moni Shoua <monis@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net/mlx4_core: Fix lockdep warning in handling of mac/vlan tables
In the mac and vlan register/unregister/replace functions, the driver locks
the mac table mutex (or vlan table mutex) on both ports.
We move to use mutex_lock_nested() to prevent warnings, such as the one below.
[ 101.828445] =============================================
[ 101.834820] [ INFO: possible recursive locking detected ]
[ 101.841199] 4.5.0-rc2+ #49 Not tainted
[ 101.850251] ---------------------------------------------
[ 101.856621] modprobe/3054 is trying to acquire lock:
[ 101.862514] (&table->mutex#2){+.+.+.}, at: [<ffffffffa079c10e>] __mlx4_register_mac+0x87e/0xa90 [mlx4_core]
[ 101.874598]
[ 101.874598] but task is already holding lock:
[ 101.881703] (&table->mutex#2){+.+.+.}, at: [<ffffffffa079c0f0>] __mlx4_register_mac+0x860/0xa90 [mlx4_core]
[ 101.893776]
[ 101.893776] other info that might help us debug this:
[ 101.901658] Possible unsafe locking scenario:
[ 101.901658]
[ 101.908859] CPU0
[ 101.911923] ----
[ 101.914985] lock(&table->mutex#2);
[ 101.919595] lock(&table->mutex#2);
[ 101.924199]
[ 101.924199] * DEADLOCK *
[ 101.924199]
[ 101.931643] May be due to missing lock nesting notation
Fixes: 5f61385d2ebc ('net/mlx4_core: Keep VLAN/MAC tables mirrored in multifunc HA mode') Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Suggested-by: Doron Tsur <doront@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This series has few bug fixes for the mlx5 Ethernet driver.
Eran fixed a locking issue with time-stamping that could cause a
soft-lockup when time-stamping is enabled.
Gal fixed the rx/tx packets/bytes counters returned by the driver to
actually went through the network stack.
Tariq removed a poll CQ optimization which could lead the driver to
stop getting interrupts for some of the rings, and a did also fix to
HW LRO which is currently broken.
He also provided RSS and RX hash fixes for the case of changing the
number of rx rings the RX hash/RSS configuration will be out of sync.
The time stamping fix from Eran is not for -stable as the feature was
only introduced in 4.5 but all of the others are.
Changes fro V0:
- Eran addressed the irqsave/restore comments from "Dave" and fixed them.
This series is generated against net commit 4c0b6eaf373a 'net:
thunderx: Fix for Qset error due to CQ full'
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Gal Pressman [Mon, 29 Feb 2016 19:17:15 +0000 (21:17 +0200)]
net/mlx5e: Provide correct packet/bytes statistics
Using the HW VPort counters for traffic (rx/tx packets/bytes)
statistics is wrong. This is because frames dropped due to steering or
out of buffer will be counted as received. To fix that, we move to use
the packet/bytes accounting done by the driver for what the netdev
reports out.
Fixes: f62b8bb8f2d3 ('net/mlx5: Extend mlx5_core to support [...]') Signed-off-by: Gal Pressman <galp@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Gal Pressman [Mon, 29 Feb 2016 19:17:14 +0000 (21:17 +0200)]
net/mlx5e: Add rx/tx bytes software counters
Sum up rx/tx bytes in software as we do for rx/tx packets, to be reported
in upcoming statistics fix.
Signed-off-by: Gal Pressman <galp@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eran Ben Elisha [Mon, 29 Feb 2016 19:17:11 +0000 (21:17 +0200)]
net/mlx5e: Fix soft lockup when HW Timestamping is enabled
Readers/Writers lock for SW timecounter was acquired without disabling
interrupts on local CPU.
The problematic scenario:
* HW timestamping is enabled
* Timestamp overflow periodic service task is running on local CPU and
holding write_lock for SW timecounter
* Completion arrives, triggers interrupt for local CPU.
Interrupt routine calls napi_schedule(), which triggers rx/tx
skb process.
An attempt to read SW timecounter using read_lock is done, which is
already locked by a writer on the same CPU and cause soft lockup.
Add irqsave/irqrestore for when using the readers/writers lock for
writing.
Fixes: ef9814deafd0 ('net/mlx5e: Add HW timestamping (TS) support') Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tariq Toukan [Mon, 29 Feb 2016 19:17:10 +0000 (21:17 +0200)]
net/mlx5e: Fix LRO modify
Ethtool LRO enable/disable is broken, as of today we only modify TCP
TIRs in order to apply the requested configuration.
Hardware requires that all TIRs pointing to the same RQ should share the
same LRO configuration. For that all other TIRs' LRO fields must be
modified as well.
Fixes: 5c50368f3831 ('net/mlx5e: Light-weight netdev open/stop') Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tariq Toukan [Mon, 29 Feb 2016 19:17:09 +0000 (21:17 +0200)]
net/mlx5e: Remove wrong poll CQ optimization
With the MLX5E_CQ_HAS_CQES optimization flag, the following buggy
flow might occur:
- Suppose RX is always busy, TX has a single packet every second.
- We poll a single TX cqe and clear its flag.
- We never arm it again as RX is always busy.
- TX CQ flag is never changed, and new TX cqes are not polled.
We revert this optimization.
Fixes: e586b3b0baee ('net/mlx5: Ethernet Datapath files') Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Chunhao Lin [Wed, 2 Mar 2016 16:59:15 +0000 (00:59 +0800)]
r8169: Enable RX_MULTI_EN for RTL_GIGA_MAC_VER_41~48
For RTL8168G/RTL8168H/RTL8411B/RTL8107E, enable this flag to eliminate
message "AMD-Vi: Event logged [IO_PAGE_FAULT device=01:00.0 domain=0x0002
address=0x0000000000003000 flags=0x0050] in dmesg.
Signed-off-by: Chunhao Lin <hau@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 2 Mar 2016 18:35:31 +0000 (13:35 -0500)]
Merge tag 'mac80211-for-davem-2016-03-02' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Here are a few more fixes for the current cycle:
* check GCMP encryption vs. fragmentation properly; we'd found
this problem quite a while ago but waited for the 802.11 spec
to be updated
* fix RTS/CTS logic in minstrel_ht
* fix RX of certain public action frames in AP mode
* add mac80211_hwsim to MAC80211 in MAINTAINERS, this helps
the kbuild robot pick up the right tree for it
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Schmidt [Wed, 2 Mar 2016 12:47:10 +0000 (13:47 +0100)]
bnx2x: define event data reserved fields as little-endian
For consistency with other event data structs and to lessen
the chance of a mistake should one of the reserved fields become
used in the future, define the reserved fields as little-endian.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Schmidt [Wed, 2 Mar 2016 12:47:09 +0000 (13:47 +0100)]
bnx2x: define fields of struct cfc_del_event_data as little-endian
There were no missing endianness conversions in this case, but the
fields of struct cfc_del_event_data should be defined as little-endian
to get rid of the ugly (__force __le32) casts.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Schmidt [Wed, 2 Mar 2016 12:47:08 +0000 (13:47 +0100)]
bnx2x: access cfc_del_event only if the opcode is CFC_DEL
It's not really a bug, but it was odd that bnx2x_eq_int() read the
message data as if it were a cfc_del_event regardless of the event type.
It's cleaner to access only the appropriate member of union event_data
after checking the event opcode.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Schmidt [Wed, 2 Mar 2016 12:47:06 +0000 (13:47 +0100)]
bnx2x: fix sending VF->PF messages on big-endian
When a VF is sending a message to the PF, it needs to trigger the PF
to tell it the message is ready.
The trigger did not work on ppc64. No interrupt appeared in the PF.
The bug is due to confusion about the layout of struct trigger_vf_zone.
In bnx2x_send_msg2pf() the trigger is written using writeb(), not
writel(), so the attempt to define the struct with a reversed layout on
big-endian is counter-productive.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Schmidt [Wed, 2 Mar 2016 12:47:05 +0000 (13:47 +0100)]
bnx2x: fix crash on big-endian when adding VLAN
bnx2x crashes during the initialization of the 8021q module on ppc64.
The bug is a missing conversion from le32 in
bnx2x_handle_classification_eqe() when obtaining the cid value from
struct eth_event_data.
The fields in struct eth_event_data should all be declared as
little-endian and conversions added where missing.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg [Fri, 26 Feb 2016 09:50:34 +0000 (10:50 +0100)]
mac80211_hwsim: treat as part of mac80211 for MAINTAINERS
Since I maintain this driver as part of mac80211, add it to
the file list for mac80211; this helps submitters send it to
me instead of Kalle and also makes the build robot apply the
patches for it on the right tree for build attempts.
Acked-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Xin Long [Sun, 28 Feb 2016 02:33:11 +0000 (10:33 +0800)]
sctp: sctp_remaddr_seq_show use the wrong variable to dump transport info
Now in sctp_remaddr_seq_show(), we use variable *tsp to get the param *v.
but *tsp is also used to traversal transport_addr_list, which will cover
the previous value, and make sctp_transport_put work on the wrong transport.
So fix it by adding a new variable to get the param *v.
Fixes: fba4c330c5b9 ("sctp: hold transport before we access t->asoc in sctp proc") Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Sun, 28 Feb 2016 02:03:51 +0000 (10:03 +0800)]
sctp: lack the check for ports in sctp_v6_cmp_addr
As the member .cmp_addr of sctp_af_inet6, sctp_v6_cmp_addr should also check
the port of addresses, just like sctp_v4_cmp_addr, cause it's invoked by
sctp_cmp_addr_exact().
Now sctp_v6_cmp_addr just check the port when two addresses have different
family, and lack the port check for two ipv6 addresses. that will make
sctp_hash_cmp() cannot work well.
so fix it by adding ports comparison in sctp_v6_cmp_addr().
Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 1 Mar 2016 21:52:09 +0000 (16:52 -0500)]
Merge branch 'phy-micrel-fixes'
Alexandre Belloni says:
====================
phy: micrel: fix issues with interrupt on atmel boards
Since the phy is not polled anymore, there were issues getting a link on the
sama5d* xplained boards.
I'm not too sure about were those fixes should go and I'm wondering whether the
first one shoud be made generic.
For the second one, I found the PHY_HAS_MAGICANEG flag that is not used and I
wondering whether this is related to that kind of issue. I had a quick look at
the history and could'nt find its use.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Disable auto negotiation on init to properly detect an already plugged
cable at boot.
At boot, when the phy is started, it is in the PHY_UP state.
However, if a cable is plugged at boot, because auto negociation is already
enabled at the time we get the first interrupt, the phy is already running.
But the state machine then switches from PHY_UP to PHY_AN and calls
phy_start_aneg(). phy_start_aneg() will not do anything because aneg is
already enabled on the phy. It will then wait for a interrupt before going
further. This interrupt will never happen unless the cable is unplugged and
then replugged.
It was working properly before 321beec5047a (net: phy: Use interrupts when
available in NOLINK state) because switching to NOLINK meant starting
polling the phy, even if IRQ were enabled.
Fixes: 321beec5047a (net: phy: Use interrupts when available in NOLINK state) Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Signed-off-by: David S. Miller <davem@davemloft.net>
phy: micrel: Ensure interrupts are reenabled on resume
At least on ksz8081, when getting back from power down, interrupts are
disabled. ensure they are reenabled if they were previously enabled.
This fixes resuming which is failing on the xplained boards from atmel
since 321beec5047a (net: phy: Use interrupts when available in NOLINK
state)
Fixes: 321beec5047a (net: phy: Use interrupts when available in NOLINK state) Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Guillaume Nault [Fri, 26 Feb 2016 17:45:34 +0000 (18:45 +0100)]
ppp: lock ppp->flags in ppp_read() and ppp_poll()
ppp_read() and ppp_poll() can be called concurrently with ppp_ioctl().
In this case, ppp_ioctl() might call ppp_ccp_closed(), which may update
ppp->flags while ppp_read() or ppp_poll() is reading it.
The update done by ppp_ccp_closed() isn't atomic due to the bit mask
operation ('ppp->flags &= ~(SC_CCP_OPEN | SC_CCP_UP)'), so concurrent
readers might get transient values.
Reading incorrect ppp->flags may disturb the 'ppp->flags & SC_LOOP_TRAFFIC'
test in ppp_read() and ppp_poll(), which in turn can lead to improper
decision on whether the PPP unit file is ready for reading or not.
Since ppp_ccp_closed() is protected by the Rx and Tx locks (with
ppp_lock()), taking the Rx lock is enough for ppp_read() and ppp_poll()
to guarantee that ppp_ccp_closed() won't update ppp->flags
concurrently.
The same reasoning applies to ppp->n_channels. The 'n_channels' field
can also be written to concurrently by ppp_ioctl() (through
ppp_connect_channel() or ppp_disconnect_channel()). These writes aren't
atomic (simple increment/decrement), but are protected by both the Rx
and Tx locks (like in the ppp->flags case). So holding the Rx lock
before reading ppp->n_channels also prevents concurrent writes.
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr> Signed-off-by: David S. Miller <davem@davemloft.net>
Ivan Vecera [Fri, 26 Feb 2016 08:15:50 +0000 (09:15 +0100)]
bna: fix list corruption
Use list_move_tail() to move MAC address entry from list of pending
to list of active entries. Simple list_add_tail() leaves the entry
also in the first list, this leads to list corruption.
Cc: Rasesh Mody <rasesh.mody@qlogic.com> Signed-off-by: Ivan Vecera <ivecera@redhat.com> Acked-by: Rasesh Mody <rasesh.mody@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jouni Malinen [Mon, 29 Feb 2016 22:29:00 +0000 (00:29 +0200)]
mac80211: Fix Public Action frame RX in AP mode
Public Action frames use special rules for how the BSSID field (Address
3) is set. A wildcard BSSID is used in cases where the transmitter and
recipient are not members of the same BSS. As such, we need to accept
Public Action frames with wildcard BSSID.
Commit db8e17324553 ("mac80211: ignore frames between TDLS peers when
operating as AP") added a rule that drops Action frames to TDLS-peers
based on an Action frame having different DA (Address 1) and BSSID
(Address 3) values. This is not correct since it misses the possibility
of BSSID being a wildcard BSSID in which case the Address 1 would not
necessarily match.
Fix this by allowing mac80211 to accept wildcard BSSID in an Action
frame when in AP mode.
Fixes: db8e17324553 ("mac80211: ignore frames between TDLS peers when operating as AP") Cc: stable@vger.kernel.org Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Fri, 26 Feb 2016 21:13:40 +0000 (22:13 +0100)]
mac80211: check PN correctly for GCMP-encrypted fragmented MPDUs
Just like for CCMP we need to check that for GCMP the fragments
have PNs that increment by one; the spec was updated to fix this
security issue and now has the following text:
The receiver shall discard MSDUs and MMPDUs whose constituent
MPDU PN values are not incrementing in steps of 1.
Adapt the code for CCMP to work for GCMP as well, luckily the
relevant fields already alias each other so no code duplication
is needed (just check the aliasing with BUILD_BUG_ON.)
Cc: stable@vger.kernel.org Signed-off-by: Johannes Berg <johannes.berg@intel.com>
3c59x: fix another page map/single unmap imbalance
Which correctly rebalanced dma mapping and unmapping types. Unfortunately it
introduced a new bug which causes oopses on older systems.
When mapping dma regions, the last entry for a packet in the 3c59x tx ring
encodes a LAST_FRAG bit, which is encoded as the high order bit of the buffers
length field. When it is unmapped the LAST_FRAG bit is cleared prior to being
passed to the unmap function. Unfortunately the commit above fails to do that
masking. It was missed in testing because the system on which I tested it had
an intel iommu, the driver for which ignores the size field, using only the DMA
address as the token to identify the mapping to be released. However, on older
systems that rely on swiotlb (or other dma drivers that key off that length
field), not masking off that LAST_FRAG high order bit results in parsing a huge
size to be release, leading to all sorts of odd corruptions and the like.
Fix is easy, just mask the length with 0xFFF. It should really be
&(LAST_FRAG-1), but 0xFFF is the style of the file, and I'd like to make this
fix minimal and correct before making it prettier.
Appies to the net tree cleanly. All testing on both iommu and swiommu based
systems produce good results
Signed-off-by: Neil Horman <nhorman@tuxdriver.com> CC: Steffen Klassert <klassert@mathematik.tu-chemnitz.de> CC: "David S. Miller" <davem@davemloft.net> Signed-off-by: David S. Miller <davem@davemloft.net>
net: ndo_fdb_dump should report -EMSGSIZE to rtnl_fdb_dump.
When the send skbuff reaches the end, nlmsg_put and friends returns
-EMSGSIZE but it is silently thrown away in ndo_fdb_dump. It is called
within a for_each_netdev loop and the first fdb entry of a following
netdev could fit in the remaining skbuff. This breaks the mechanism
of cb->args[0] and idx to keep track of the entries that are already
dumped, which results missing entries in bridge fdb show command.
Signed-off-by: Minoura Makoto <minoura@valinux.co.jp> Signed-off-by: David S. Miller <davem@davemloft.net>
can: gs_usb: fixed disconnect bug by removing erroneous use of kfree()
gs_destroy_candev() erroneously calls kfree() on a struct gs_can *, which is
allocated through alloc_candev() and should instead be freed using
free_candev() alone.
The inappropriate use of kfree() causes the kernel to hang when
gs_destroy_candev() is called.
Only the struct gs_usb * which is allocated through kzalloc() should be freed
using kfree() when the device is disconnected.
Signed-off-by: Maximilian Schneider <max@schneidersoft.net> Cc: linux-stable <stable@vger.kernel.org> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Sunil Goutham [Wed, 24 Feb 2016 11:10:50 +0000 (16:40 +0530)]
net: thunderx: Fix for Qset error due to CQ full
On Thunderx pass 1.x and pass2 due to a HW errata default CQ
DROP_LEVEL of 0x80 is not sufficient to avoid CQ_WR_FULL Qset
error when packets are being received at >20Mpps resulting in
complete stall of packet reception.
This patch will configure it to 0x100 which is what is expected
by HW on Thunderx. On future passes of thunderx and other chips
HW default/reset value will be 0x100 or higher hence not overwritten.
Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com> Signed-off-by: Sunil Goutham <sgoutham@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
There will be a log spam when there is no cable plugged. Please refer to
following links. https://bugzilla.kernel.org/show_bug.cgi?id=104351
https://bugzilla.kernel.org/show_bug.cgi?id=107421
This issue is caused by runtime power management. When there is no cable
plugged, the driver will be suspend (runtime suspend) by OS and NIC will be
put into the D3 state. During this time, if OS call rtl8169_get_stats64()
to dump tally counter, because NIC is in D3 state, the register value read
by driver will return all 0xff. This will let driver think tally counter
flag is not toggled and then sends the warning message "rtl_counters_cond
== 1 (loop: 1000, delay: 10)" to kernel log.
For fixing this issue, 1.add checking driver's pm runtime status in
rtl8169_get_stats64(). 2.dump tally counter before going runtime suspend
for counter accuracy in runtime suspend.
Signed-off-by: Chunhao Lin <hau@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
We need to update the skb->csum after pulling the skb, otherwise
an unnecessary checksum (re)computation can ocure for IGMP/MLD packets
in the bridge code. Additionally this fixes the following splats for
network devices / bridge ports with support for and enabled RX checksum
offloading:
[...]
[ 43.986968] eth0: hw csum failure
[ 43.990344] CPU: 3 PID: 0 Comm: swapper/3 Not tainted 4.4.0 #2
[ 43.996193] Hardware name: BCM2709
[ 43.999647] [<800204e0>] (unwind_backtrace) from [<8001cf14>] (show_stack+0x10/0x14)
[ 44.007432] [<8001cf14>] (show_stack) from [<801ab614>] (dump_stack+0x80/0x90)
[ 44.014695] [<801ab614>] (dump_stack) from [<802e4548>] (__skb_checksum_complete+0x6c/0xac)
[ 44.023090] [<802e4548>] (__skb_checksum_complete) from [<803a055c>] (ipv6_mc_validate_checksum+0x104/0x178)
[ 44.032959] [<803a055c>] (ipv6_mc_validate_checksum) from [<802e111c>] (skb_checksum_trimmed+0x130/0x188)
[ 44.042565] [<802e111c>] (skb_checksum_trimmed) from [<803a06e8>] (ipv6_mc_check_mld+0x118/0x338)
[ 44.051501] [<803a06e8>] (ipv6_mc_check_mld) from [<803b2c98>] (br_multicast_rcv+0x5dc/0xd00)
[ 44.060077] [<803b2c98>] (br_multicast_rcv) from [<803aa510>] (br_handle_frame_finish+0xac/0x51c)
[...]
Fixes: 9afd85c9e455 ("net: Export IGMP/MLD message validation code") Reported-by: Álvaro Fernández Rojas <noltari@gmail.com> Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue> Signed-off-by: David S. Miller <davem@davemloft.net>
Stefan Wahren [Tue, 23 Feb 2016 19:23:24 +0000 (19:23 +0000)]
net: qca_spi: clear IFF_TX_SKB_SHARING
ether_setup sets IFF_TX_SKB_SHARING but this is not supported by
qca_spi as it modifies the skb on xmit.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Fixes: 291ab06ecf67 (net: qualcomm: new Ethernet over SPI driver for QCA7000) Signed-off-by: David S. Miller <davem@davemloft.net>
Stefan Wahren [Tue, 23 Feb 2016 19:23:23 +0000 (19:23 +0000)]
net: qca_spi: Don't clear IFF_BROADCAST
Currently qcaspi_netdev_setup accidentally clears IFF_BROADCAST.
So fix this by keeping the flags from ether_setup.
Reported-by: Michael Heimpold <michael.heimpold@i2se.com> Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Fixes: 291ab06ecf67 (net: qualcomm: new Ethernet over SPI driver for QCA7000) Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Tue, 23 Feb 2016 18:10:26 +0000 (10:10 -0800)]
net: vrf: Remove direct access to skb->data
Nik pointed that the VRF driver should be using skb_header_pointer
instead of accessing skb->data and bits beyond directly which can
be garbage.
Fixes: 35402e313663 ("net: Add IPv6 support to VRF device") Cc: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Diego Viola [Tue, 23 Feb 2016 15:04:04 +0000 (12:04 -0300)]
net: jme: fix suspend/resume on JMC260
The JMC260 network card fails to suspend/resume because the call to
jme_start_irq() was too early, moving the call to jme_start_irq() after
the call to jme_reset_link() makes it work.
Prior this change suspend/resume would fail unless /sys/power/pm_async=0
was explicitly specified.
David S. Miller [Wed, 24 Feb 2016 21:58:12 +0000 (16:58 -0500)]
Merge tag 'mac80211-for-davem-2016-02-23' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Another small set of fixes:
* stop critical protocol session on disconnect to avoid
it getting stuck
* wext: fix two RTNL message ordering issues
* fix an uninitialized value (found by KASAN)
* fix an out-of-bounds access (also found by KASAN)
* clear connection keys when freeing them in all cases
(IBSS, all other places already did so)
* fix expected throughput unit to get consistent values
* set default TX aggregation timeout to 0 in minstrel
to avoid (really just hide) issues and perform better
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Tue, 23 Feb 2016 01:05:26 +0000 (02:05 +0100)]
bpf: fix csum setting for bpf_set_tunnel_key
The fix in 35e2d1152b22 ("tunnels: Allow IPv6 UDP checksums to be correctly
controlled.") changed behavior for bpf_set_tunnel_key() when in use with
IPv6 and thus uncovered a bug that TUNNEL_CSUM needed to be set but wasn't.
As a result, the stack dropped ingress vxlan IPv6 packets, that have been
sent via eBPF through collect meta data mode due to checksum now being zero.
Since after LCO, we enable IPv4 checksum by default, so make that analogous
and only provide a flag BPF_F_ZERO_CSUM_TX for the user to turn it off in
IPv4 case.
Fixes: 35e2d1152b22 ("tunnels: Allow IPv6 UDP checksums to be correctly controlled.") Fixes: c6c33454072f ("bpf: support ipv6 for bpf_skb_{set,get}_tunnel_key") Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
ipv4: only create late gso-skb if skb is already set up with CHECKSUM_PARTIAL
Otherwise we break the contract with GSO to only pass CHECKSUM_PARTIAL
skbs down. This can easily happen with UDP+IPv4 sockets with the first
MSG_MORE write smaller than the MTU, second write is a sendfile.
Returning -EOPNOTSUPP lets the callers fall back into normal sendmsg path,
were we calculate the checksum manually during copying.
Commit d749c9cbffd6 ("ipv4: no CHECKSUM_PARTIAL on MSG_MORE corked
sockets") started to exposes this bug.
Fixes: d749c9cbffd6 ("ipv4: no CHECKSUM_PARTIAL on MSG_MORE corked sockets") Reported-by: Jiri Benc <jbenc@redhat.com> Cc: Jiri Benc <jbenc@redhat.com> Reported-by: Wakko Warner <wakko@animx.eu.org> Cc: Wakko Warner <wakko@animx.eu.org> Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Sebastian Frias [Mon, 22 Feb 2016 12:33:14 +0000 (13:33 +0100)]
net: ethernet: nb8800: support fixed-link DT node
Under some circumstances, e.g. when connecting to a switch, the ethernet
port will not be connected to a PHY. In that case a "fixed-link" DT node
can be used to replace it.
This patch adds support for the "fixed-link" node to the nb8800 driver.
Signed-off-by: Sebastian Frias <sf84@laposte.net> Acked-by: Mans Rullgard <mans@mansr.com> Cc: Mason <slash.tmp@free.fr> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Mon, 22 Feb 2016 07:10:26 +0000 (02:10 -0500)]
bnxt_en: Fix zero padding of tx push data.
The arithmetic to zero pad the last 64-bit word in the push buffer is not
correct.
1. It should be pdata + length to get to the end.
2. 'pdata' is void pointer and passing it to PTR_ALIGN() will cast the
aligned pointer to void. Pass 'end' which is u64 pointer to PTR_ALIGN()
instead so that the aligned pointer - 1 is the last 64-bit pointer to data.
Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bernie Harris [Sun, 21 Feb 2016 23:58:05 +0000 (12:58 +1300)]
tunnel: Clear IPCB(skb)->opt before dst_link_failure called
IPCB may contain data from previous layers (in the observed case the
qdisc layer). In the observed scenario, the data was misinterpreted as
ip header options, which later caused the ihl to be set to an invalid
value (<5). This resulted in an infinite loop in the mips implementation
of ip_fast_csum.
This patch clears IPCB(skb)->opt before dst_link_failure can be called for
various types of tunnels. This change only applies to encapsulated ipv4
packets.
The code introduced in 11c21a30 which clears all of IPCB has been removed
to be consistent with these changes, and instead the opt field is cleared
unconditionally in ip_tunnel_xmit. The change in ip_tunnel_xmit applies to
SIT, GRE, and IPIP tunnels.
The relevant vti, l2tp, and pptp functions already contain similar code for
clearing the IPCB.
Signed-off-by: Bernie Harris <bernie.harris@alliedtelesis.co.nz> Signed-off-by: David S. Miller <davem@davemloft.net>
tcp: convert cached rtt from usec to jiffies when feeding initial rto
Currently it's converted into msecs, thus HZ=1000 intact.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru> Fixes: 740b0f1841f6 ("tcp: switch rtt estimations to usec resolution") Signed-off-by: David S. Miller <davem@davemloft.net>
Arend van Spriel [Mon, 15 Feb 2016 13:35:53 +0000 (14:35 +0100)]
cfg80211: stop critical protocol session upon disconnect event
When user-space has started a critical protocol session and a disconnect
event occurs, the rdev::crit_prot_nlportid remains set. This caused a
subsequent NL80211_CMD_CRIT_PROTO_START to fail (-EBUSY). Fix this by
clearing the rdev attribute and call .crit_proto_stop() callback upon
disconnect event.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Felix Fietkau [Thu, 18 Feb 2016 18:49:18 +0000 (19:49 +0100)]
mac80211: minstrel_ht: set default tx aggregation timeout to 0
The value 5000 was put here with the addition of the timeout field to
ieee80211_start_tx_ba_session. It was originally added in mac80211 to
save resources for drivers like iwlwifi, which only supports a limited
number of concurrent aggregation sessions.
Since iwlwifi does not use minstrel_ht and other drivers don't need
this, 0 is a better default - especially since there have been
recent reports of aggregation setup related issues reproduced with
ath9k. This should improve stability without causing any adverse
effects.
Cc: stable@vger.kernel.org Acked-by: Avery Pennarun <apenwarr@gmail.com> Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pull networking fixes from David Miller:
"Looks like a lot, but mostly driver fixes scattered all over as usual.
Of note:
1) Add conditional sched in nf conntrack in cleanup to avoid NMI
watchdogs. From Florian Westphal.
2) Fix deadlock in nfnetlink cttimeout, also from Floarian.
3) Fix handling of slaves in bonding ARP monitor validation, from Jay
Vosburgh.
4) Callers of ip_cmsg_send() are responsible for freeing IP options,
some were not doing so. Fix from Eric Dumazet.
5) Fix per-cpu bugs in mvneta driver, from Gregory CLEMENT.
6) Fix vlan handling in mv88e6xxx DSA driver, from Vivien Didelot.
7) bcm7xxx PHY driver bug fixes from Florian Fainelli.
8) Avoid unaligned accesses to protocol headers wrt. GRE, from
Alexander Duyck.
9) SKB leaks and other problems in arc_emac driver, from Alexander
Kochetkov.
10) tcp_v4_inbound_md5_hash() releases listener socket instead of
request socket on error path, oops. Fix from Eric Dumazet.
11) Missing socket release in pppoe_rcv_core() that seems to have
existed basically forever. From Guillaume Nault.
12) Missing slave_dev unregister in dsa_slave_create() error path,
from Florian Fainelli.
13) crypto_alloc_hash() never returns NULL, fix return value check in
__tcp_alloc_md5sig_pool. From Insu Yun.
14) Properly expire exception route entries in ipv4, from Xin Long.
15) Fix races in tcp/dccp listener socket dismantle, from Eric
Dumazet.
16) Don't set IFF_TX_SKB_SHARING in vxlan, geneve, or GRE, it's not
legal. These drivers modify the SKB on transmit. From Jiri Benc.
17) Fix regression in the initialziation of netdev->tx_queue_len.
From Phil Sutter.
18) Missing unlock in tipc_nl_add_bc_link() error path, from Insu Yun.
19) SCTP port hash sizing does not properly ensure that table is a
power of two in size. From Neil Horman.
20) Fix initializing of software copy of MAC address in fmvj18x_cs
driver, from Ken Kawasaki"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (129 commits)
bnx2x: Fix 84833 phy command handler
bnx2x: Fix led setting for 84858 phy.
bnx2x: Correct 84858 PHY fw version
bnx2x: Fix 84833 RX CRC
bnx2x: Fix link-forcing for KR2
net: ethernet: davicom: fix devicetree irq resource
fmvj18x_cs: fix incorrect indexing of dev->dev_addr[] when copying the MAC address
Driver: Vmxnet3: Update Rx ring 2 max size
net: netcp: rework the code for get/set sw_data in dma desc
soc: ti: knav_dma: rename pad in struct knav_dma_desc to sw_data
net: ti: netcp: restore get/set_pad_info() functionality
MAINTAINERS: Drop myself as xen netback maintainer
sctp: Fix port hash table size computation
can: ems_usb: Fix possible tx overflow
Bluetooth: hci_core: Avoid mixing up req_complete and req_complete_skb
net: bcmgenet: Fix internal PHY link state
af_unix: Don't use continue to re-execute unix_stream_read_generic loop
unix_diag: fix incorrect sign extension in unix_lookup_by_ino
bnxt_en: Failure to update PHY is not fatal condition.
bnxt_en: Remove unnecessary call to update PHY settings.
...
Linus Torvalds [Mon, 22 Feb 2016 20:04:11 +0000 (12:04 -0800)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma fixes from Doug Ledford:
"One ocrdma fix:
- The new CQ API support was added to ocrdma, but they got the arming
logic wrong, so without this, transfers eventually fail when they
fail to arm the interrupt properly under load
Two related fixes for mlx4:
- When we added the 64bit extended counters support to the core IB
code, they forgot to update the RoCE side of the mlx4 driver (the
IB side they properly updated).
I debated whether or not to include these patches as they could be
considered feature enablement patches, but the existing code will
blindy copy the 32bit counters, whether any counters were requested
at all (a bug).
These two patches make it (a) check to see that counters were
requested and (b) copy the right counters (the 64bit support is
new, the 32bit is not). For that reason I went ahead and took
them"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma:
IB/mlx4: Add support for the port info class for RoCE ports
IB/mlx4: Add support for extended counters over RoCE ports
RDMA/ocrdma: Fix arm logic to align with new cq API
Linus Torvalds [Mon, 22 Feb 2016 19:55:18 +0000 (11:55 -0800)]
Merge branch 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"Some bugfixes from I2C for you:
A fix for a RuntimePM regression with OMAP, a fix to enable TCO for
Lewisburg platforms, and a typo fix while we are here"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: i801: Adding Intel Lewisburg support for iTCO
i2c: uniphier: fix typos in error messages
i2c: omap: Fix PM regression with deferred probe for pm_runtime_reinit
Yuval Mintz [Sun, 21 Feb 2016 13:07:26 +0000 (15:07 +0200)]
bnx2x: Fix 84833 RX CRC
There's a problem in current 84833 phy configuration -
in case 1Gb link is configured and jumbo-sized packets are being
used, device will experience RX crc errors.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / karo-tx-linux.git / log