When multiple channel contexts are enabled, a p2p interface
that is assigned to a context will have an address that
is different from the device mac address, which is used
by wpa_s as the p2p device ID.
Certain frames like provision requests use the device address
and these get dropped since ath9k_calculate_summary_state()
iterates over only the active interfaces in a context and the
device address is not used.
Fix this by adding the device mac address to the bssid mask.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some chip IDs are easier to read/understand when printed in a decimal
form. For example on my bcm53xx arch router this patch replaces:
Found chip with id 0xCF12, rev 0x00 and package 0x02
with a:
Found chip with id 53010, rev 0x00 and package 0x02
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
mwifiex: ensure user_scan_in not NULL while setting scan channel gap
Check for scan channel gap only when user_scan_in is not NULL.
user_scan_in is NULL for internal scans and if we check scan channel gap
at this place, it may result into crash.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Cathy Luo <cluo@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using the BSS information stored in mac80211 directly
is racy in certain conditions. For example, in a MCC
setup, if the scheduler is switching channels when
a local deauth is issued, calculation of the opmode/bssid
etc. is incorrect. To avoid this, store the bss params
in the driver and use it.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Paul Bolle [Wed, 10 Sep 2014 08:53:41 +0000 (10:53 +0200)]
ath5k: Remove AHB bus support
AHB bus support was added in v2.6.38, through commit a0b907ee2a71
("ath5k: Add AHB bus support."). That code can only be build if the
Kconfig symbol ATHEROS_AR231X is set. But that symbol has never been
added to the tree. So AHB bus support has always been dead code.
Let's remove all code that depends on ATHEROS_AR231X. If that symbol
ever gets added to the tree the AHB bus support can be re-added too.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl> Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville [Fri, 26 Sep 2014 17:37:02 +0000 (13:37 -0400)]
Merge tag 'nfc-next-3.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/nfc-next
Samuel Ortiz <sameo@linux.intel.com> says:
"NFC: 3.18 pull request
This is the NFC pull request for 3.18.
We've had major updates for TI and ST Microelectronics drivers:
For TI's trf7970a driver:
- Target mode support for trf7970a
- Suspend/resume support for trf7970a
- DT properties additions to handle different quirks
- A bunch of fixes for smartphone IOP related issues
For ST Microelectronics' ST21NFCA and ST21NFCB drivers:
- ISO15693 support for st21nfcb
- checkpatch and sparse related warning fixes
- Code cleanups and a few minor fixes
Finally, Marvell add ISO15693 support to the NCI stack, together with a
couple of NCI fixes."
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johan Hedberg [Thu, 25 Sep 2014 06:48:01 +0000 (09:48 +0300)]
Bluetooth: Rename sco_param_wideband table to esco_param_msbc
The sco_param_wideband table represents the eSCO parameters for
specifically mSBC encoding. This patch renames the table to the more
descriptive esco_param_msbc name.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Johan Hedberg [Wed, 24 Sep 2014 19:41:46 +0000 (22:41 +0300)]
Bluetooth: Add retransmission effort into SCO parameter table
It is expected that new parameter combinations will have the
retransmission effort value different between some entries (mainly
because of the new S4 configuration added by HFP 1.7), so it makes sense
to move it into the table instead of having it hard coded based on the
selected SCO_AIRMODE_*.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Simon Vincent [Wed, 24 Sep 2014 10:21:33 +0000 (12:21 +0200)]
ieee802154: 6lowpan: ensure header compression does not corrupt ipv6 header
The 6lowpan ipv6 header compression was causing problems for other interfaces
that expected a ipv6 header to still be in place, as we were replacing the
ipv6 header with a compressed version. This happened if you sent a packet to a
multicast address as the packet would be output on 802.15.4, ethernet, and also
be sent to the loopback interface. The skb data was shared between these
interfaces so all interfaces ended up with a compressed ipv6 header.
The solution is to ensure that before we do any header compression we are not
sharing the skb or skb data with any other interface. If we are then we must
take a copy of the skb and skb data before modifying the ipv6 header.
The only place we can copy the skb is inside the xmit function so we don't
leave dangling references to skb.
This patch moves all the header compression to inside the xmit function. Very
little code has been changed it has mostly been moved from lowpan_header_create
to lowpan_xmit. At the top of the xmit function we now check if the skb is
shared and if so copy it. In lowpan_header_create all we do now is store the
source and destination addresses for use later when we compress the header.
Signed-off-by: Simon Vincent <simon.vincent@xsilon.com> Signed-off-by: Alexander Aring <alex.aring@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Johan Hedberg [Wed, 24 Sep 2014 10:14:46 +0000 (13:14 +0300)]
Bluetooth: Fix reason code used for rejecting SCO connections
The core specification defines valid values for the
HCI_Reject_Synchronous_Connection_Request command to be 0x0D-0x0F. So
far the code has been using HCI_ERROR_REMOTE_USER_TERM (0x13) which is
not a valid value and is therefore being rejected by some controllers:
This patch introduces a new define for a value from the valid range
(0x0d == Connection Rejected Due To Limited Resources) and uses it
instead for rejecting incoming connections.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
"skb" can be NULL here but it can't be an ERR_PTR:
- IS_ERR(NULL) return false and skb migth be NULL.
- skb cannot be a ERR_PTR as nfc_hci_send_cmd_async it never using such cast.
!skb is more appropriate at those places.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In case we are not able to read out the NDLC/NCI header, we do not
consider this as an issue and we will give a later chance.
The NDLC layer will handle errors thanks to its internal timers.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
NFC: nci: Add support for proprietary RF Protocols
In NFC Forum NCI specification, some RF Protocol values are
reserved for proprietary use (from 0x80 to 0xfe).
Some CLF vendor may need to use one value within this range
for specific technology.
Furthermore, some CLF may not becompliant with NFC Froum NCI
specification 2.0 and therefore will not support RF Protocol
value 0x06 for PROTOCOL_T5T as mention in a draft specification
and in a recent push.
Adding get_rf_protocol handle to the nci_ops structure will
help to set the correct technology to target.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
NFC: st21nfcb: Fix improper management of -EREMOTEIO error code.
On st21nfcb the irq line might be kept to active state because of other
interfaces activity. This may generate i2c read tentative resulting in
i2c NACK.
This fix will currently let NDLC upper layer to decide when it is relevent
to signal to the physical layer when the chip as muted.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
It is actually fixing a double free mistake in all st21nfca_tm_* function.
We decide to return directly in case of successful execution because skb
got already freed. In st21nfca_tm_recv_dep_req it got freed by nfc_tm_data_received.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Mark A. Greer [Tue, 23 Sep 2014 18:25:48 +0000 (11:25 -0700)]
NFC: trf7970a: Unlock mutex before exiting _trf7970a_tg_listen()
The recently added _trf7970a_tg_listen() routine
has some return paths that don't unlock the mutex
that is locked when the routine is entered. Fix
this by always unlocking the mutex before returning.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Mark A. Greer [Tue, 23 Sep 2014 18:25:47 +0000 (11:25 -0700)]
NFC: trf7970a: Unlock mutex before exiting trf7970a_irq()
Recent changes to trf7970a_irq() added a couple return
paths that don't unlock the mutex that is locked when
the routine is entered. Fix this by ensuring the mutex
is always unlocked before returning.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Bernhard Thaler [Tue, 23 Sep 2014 09:01:07 +0000 (11:01 +0200)]
Bluetooth: Check for SCO type before setting retransmission effort
SCO connection cannot be setup to devices that do not support retransmission.
Patch based on http://permalink.gmane.org/gmane.linux.bluez.kernel/7779 and
adapted for this kernel version.
Code changed to check SCO/eSCO type before setting retransmission effort
and max. latency. The purpose of the patch is to support older devices not
capable of eSCO.
Tested on Blackberry 655+ headset which does not support retransmission.
Credits go to Alexander Sommerhuber.
Signed-off-by: Bernhard Thaler <bernhard.thaler@r-it.at> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
iwlwifi: mvm: Refactor and fix max probe len computation
Move iwl_mvm_max_scan_ie_len function to scan.c and fix the
implementation to conform with the LMAC scan API.
Since the correct implementation would leave us with unacceptably
tiny probes, add a workaround which returns a larger value.
In current implementation it's possible that unified_scan_lmac and
unified_sched_scan_lmac would return -ENOBUFS.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
iwlwifi: mvm: rs: fix logic in case of multiple TIDs
In case of traffic on multiple TIDs where one is aggregated
and the other is not RS would toggle between considering
traffic vs. the station as aggregated and not aggregated.
Instead consider the sta state as aggregated as long as
there's at least one TID aggregated.
This limitation is because the rates table is kept per
station and not per TID.
Currently BA notifications which don't reclaim any frames
would not cause the RS to be called as no skbs are passed
to mac80211. This is not optimal as RS can benefit from the
statistics of sent vs. acked of such a BA. This can improve the
reaction time of the RS algorithm. Also, an upcoming change in
the firmware would cause BA timeout to be reported as a BA notif
with 0 acked so this change is required for that as well.
iwlwifi: mvm: limit aggregation size in low latency to 6
This is a tradeoff between enabling better throughput for
bursty traffic and low latency. The number 6 was found to be
a good tradeoff for the Miracast use case which is the
major use case for low latency.
iwlwifi: mvm: rs: refactor to allow direct rs updating
Enable RS to get updated directly via iwl_mvm_rs_tx_status
which will be called by the driver and not via mac80211
rate control. This is required for a following patch to
report on BAs which do not cause the BA window to progress.
Also this is a first step in decoupling rs from the
mac80211 rate control.
Eyal Shapira [Tue, 12 Aug 2014 21:31:13 +0000 (00:31 +0300)]
iwlwifi: mvm: choose an initial tx rate based on rssi conditions
Improve the initial tx rate and antenna selection to be based on
the rssi of the last rx. This avoids starting at the lowest legacy
rate always and requiring more tx traffic to "climb" up the rates.
Since this option might cause trouble in certain setups, allow to
disable it by default.
Johan Hedberg [Thu, 18 Sep 2014 08:26:32 +0000 (11:26 +0300)]
Bluetooth: Fix setting correct security level when initiating SMP
We can only determine the final security level when both pairing request
and response have been exchanged. When initiating pairing the starting
target security level is set to MEDIUM unless explicitly specified to be
HIGH, so that we can still perform pairing even if the remote doesn't
have MITM capabilities. However, once we've received the pairing
response we should re-consult the remote and local IO capabilities and
upgrade the target security level if necessary.
Without this patch the resulting Long Term Key will occasionally be
reported to be unauthenticated when it in reality is an authenticated
one.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Cc: stable@vger.kernel.org
Kalle Valo [Sun, 14 Sep 2014 09:50:49 +0000 (12:50 +0300)]
ath10k: use ether_addr_copy()
As suggeested by checkpatch:
WARNING: Prefer ether_addr_copy() over memcpy() if the Ethernet addresses are __aligned(2)
In wmi.c I had to change due to sparse warnings copying of struct wmi_mac_addr
from form &cmd->peer_macaddr.addr to cmd->peer_macaddr.addr. In
ath10k_wmi_set_ap_ps_param() I also added the missing ".addr" to the copy
command.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Kalle Valo [Sun, 14 Sep 2014 09:50:39 +0000 (12:50 +0300)]
ath10k: miscellaneous checkpatch fixes
Fixes checkpatch warnings:
ath10k/htc.c:49: WARNING: Possible unnecessary 'out of memory' message
ath10k/htc.c:810: WARNING: Possible unnecessary 'out of memory' message
ath10k/htt.h:1034: CHECK: Please use a blank line after function/struct/union/enum declarations
ath10k/htt_rx.c:135: CHECK: Unnecessary parentheses around htt->rx_ring.alloc_idx.vaddr
ath10k/htt_rx.c:173: CHECK: Unnecessary parentheses around htt->rx_ring.alloc_idx.vaddr
ath10k/pci.c:633: WARNING: macros should not use a trailing semicolon
ath10k/wmi.c:3594: WARNING: quoted string split across lines
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Kalle Valo [Sun, 14 Sep 2014 09:50:17 +0000 (12:50 +0300)]
ath10k: fix missing a blank line after declarations
Fixes checkpatch warnings:
WARNING: Missing a blank line after declarations
Please note that some of the cases I fixed by moving the variable declarations
to the beginning of the function, which is the preferred style in ath10k.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Bluetooth: Remove exported hci_recv_fragment function
The hci_recv_fragment function is no longer used by any driver and thus
do not export it. In fact it is not even needed by the core and it can
be removed altogether.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This happens when CONFIG_ATH9K_CHANNEL_CONTEXT is
not enabled.
../drivers/net/wireless/ath/ath9k/recv.c: In function ‘ath_rx_ps_beacon’:
../drivers/net/wireless/ath/ath9k/recv.c:553:27: error: ‘struct ath_softc’ has no member named ‘offchannel’
if (sc->cur_chan == &sc->offchannel.chan)
^
../scripts/Makefile.build:257: recipe for target 'drivers/net/wireless/ath/ath9k/recv.o' failed
make[10]: *** [drivers/net/wireless/ath/ath9k/recv.o] Error 1
../scripts/Makefile.build:404: recipe for target 'drivers/net/wireless/ath/ath9k' failed
make[9]: *** [drivers/net/wireless/ath/ath9k] Error 2
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Lorenzo Bianconi [Tue, 16 Sep 2014 00:13:15 +0000 (02:13 +0200)]
ath9k: enable dynack using set_coverage_class codepath
Enable ACK timeout estimation algorithm if set_coverage_class routine has been
called with negative coverage_class parameter. Dynack is automatically disabled
setting valid value for coverage class
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Lorenzo Bianconi [Tue, 16 Sep 2014 00:13:12 +0000 (02:13 +0200)]
ath9k: add sampling methods for (tx|rx) timestamp
Add sampling methods for ACK RX timestamp in ath_rx_tasklet() and for TX frame
timestamp in ath_tx_complete_aggr() and in ath_tx_process_buffer(). These
samples will be used in dynack processing for ACK timeout estimation
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Lorenzo Bianconi [Tue, 16 Sep 2014 00:13:09 +0000 (02:13 +0200)]
ath9k: add dynamic ACK timeout estimation
Add dynamic ACK timeout estimation algorithm based on ACK frame RX timestamp,
TX frame timestamp and frame duration.
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com> Tested-by: Philippe Duchein <wireless-dev@duchein.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Lorenzo Bianconi [Tue, 16 Sep 2014 00:13:08 +0000 (02:13 +0200)]
ath9k: add duration field to ath_tx_status
Add duration field to ath_tx_status in order to report frame duration for each
entry in multi-retry chain. These fields will be used in ACK timeout estimation
algorithm (dynack)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Lorenzo Bianconi [Tue, 16 Sep 2014 00:13:07 +0000 (02:13 +0200)]
ath9k: export methods related to ACK timeout estimation
Remove static keyword and export ath9k_hw_setslottime(),
ath9k_hw_set_ack_timeout() and ath9k_hw_set_cts_timeout() in hw.h.
These methods will be used in ACK timeout estimation algorithm (dynack)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
When receiving USB interrupt, bulk or isochronous packet, they normally
come in fragments. So far the driver just handed each fragment off to
the hci_recv_fragment function of the Bluetooth core. That function is
however so specific that is does not belong in the core. This patch
implements the same reassembly logic in the driver.
In addition this fixes a long standing bug where multiple complete
packets are received within a single USB packet.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Alexander Bondar [Wed, 30 Jul 2014 14:40:28 +0000 (17:40 +0300)]
iwlwifi: mvm: Allow schedule scan while connected
In the past when schedule scan was started while connected on one of
interfaces FW crashes were observed. In the newest FW this issue is
solved, so remove limitaion after examining corresponding TLV flag.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com> Reviewed-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
iwlwifi: mvm: prepare for scheduler config command
The scheduler is a HW sub-block that directs the work of the Flow
Handler by issuing requests for frame transfers, specifying source
and destination. Its primary function is to allocate flows into the
TX FIFOs based upon a pre-determined mapping.
The driver has some responsibilities to the scheduler, namely
initialising and maintaining the hardware registers. This is
currently done by directly accessing them, which can cause races
with the firmware also accessing the registers.
To address this problem, change the driver to no longer directly
access the registers but go through the firmware for this if the
firmware has support for DQA and thus the new command.
iwlwifi: mvm: Set RRM_ENABLED bit in scan commands
Set RRM_ENABLED (bit 6) flag in scan commands. When this flag is set
the fw will add WFA vendor-specific TPC report and DS parameter set
IEs into probe requests.
This bit is set for SCAN_OFFLOAD_REQUEST_CMD(0x51).
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com> Reviewed-by: Assaf Krauss <assaf.krauss@intel.com> Reviewed-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Introduce new tx command flag (TX_CMD_FLG_WRITE_TX_POWER) which requests the
fw to update the tx power value at some constant offset.
Set this flag when transmitting either TPC report or Link measurement report
action frames.
In addition, introduce new tlv which indicates whether the fw supports power
insertion (IWL_UCODE_TLV_CAPA_TXPOWER_INSERTION_SUPPORT) and publish the
corresponding nl80211 feature.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com> Reviewed-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Bluetooth: btusb: Split fragement receiption into separate functions
The actual packet reassembly should be done inside the driver. To allow
this to happen cleanly in future patches, split the fragment reception
into its own functions.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The btusb driver has been around for a while now and it is time to
bring its coding style in sync with what has been done for the
Bluetooth subsystem and other drivers.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The next_tbtt variable in the scheduler is needed only
for GO/AP mode operation and is always read from the
NEXT_TBTT_TIMER in the HW. There is no need to store
the timestamp for received beacons.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some constants were missing and are added now.
The rate mode was renamed, at least the ucode in brcsmac uses 2 for HT
rates (iee80211n) and the more recent ucodes are using 3 for VHT
(ieee80211ac).
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fabian Frederick [Sat, 13 Sep 2014 20:38:29 +0000 (22:38 +0200)]
brcm80211: use container_of to resolve dma_info from dma_pub
Use container_of instead of casting first structure member.
Compiled but untested.
Signed-off-by: Fabian Frederick <fabf@skynet.be> Acked-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fabian Frederick [Sat, 13 Sep 2014 20:38:28 +0000 (22:38 +0200)]
brcm80211: use container_of to resolve brcms_phy from brcms_phy_pub
Use container_of instead of casting first structure member.
Compiled but untested.
Signed-off-by: Fabian Frederick <fabf@skynet.be> Acked-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Larry Finger [Fri, 12 Sep 2014 20:50:58 +0000 (15:50 -0500)]
rtlwifi: btcoexist: Change local debugging macros CL_*** into the standard varieties
Macros CL_SNPRINTF and CL_PRINTF are always used in that order. The first
formats info into a buffer, and the second dumps it with printk. As the
debug system in rtlwifi has a macro that does this with a single call,
it seems reasonable to use it instead. An additional benefit is that the
debug level can be set when loading the driver used by the wifi device.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds RX work queue support to mwifiex.
Packets received are queued to internal queue which are then
processed by scheduling a work item for RX process.
RX work is enabled only on SMP systems.
Reviewed-by: James Cameron <quozl@laptop.org> Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Marc Yang <yangyang@marvell.com> Signed-off-by: Cathy Luo <cluo@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
We have a logic in driver to delay or abort low priority scan
to serve Tx traffic effectively. With scan channel
gap support added, firmware now allows driver to send Tx data while
scan operation is in progress. Hence low priority scan handling
in driver is not required now. This patch removes related code.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Cathy Luo <cluo@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
With channel scan gap, FW comes back to connected channel after each
single channel scan. So we can safely transfer data to FW during scan.
FW would send this data once on connected channel.
Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Cathy Luo <cluo@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
mwifiex: remove restriction of single channel scan when connected
With scan channel gap in place, FW comes back to connected channel
after each scan; so we dont need to restrict FW to scan
single channel while connected.
Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Marc Yang <yangyang@marvell.com> Signed-off-by: Cathy Luo <cluo@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
With scan channel gap when any station/AP is active, FW comes back
to connected channel for any pending data transfter after scanning each
channel.
We set scan channel gap TLV to FW in scan command when any of the
interface is active. This enables scan channel gap in FW.
Also when scan channel gap is enabled, we would scan maximum channels
allowed by FW.
Scan channel gap is supported only on FW with V15 FW API.
Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Marc Yang <yangyang@marvell.com> Signed-off-by: Cathy Luo <cluo@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
mwifiex: set passive scan type for scan requests with no ssid
It was observed that station would sent probe request even when
scan type has been set as passive during iw scan.
This was happening because driver sets passive scan type only
when channel has IEEE80211_CHAN_NO_IR flag set.
Along with this, add condition to check if no ssids are specified in
scan request so as to mark such scan request passive.
Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
projects / linux-beck.git / log