Paul Walmsley [Fri, 11 Mar 2011 05:40:05 +0000 (22:40 -0700)]
Watchdog: omap_wdt: add fine grain runtime-pm
The omap_wdt should only be in full active state when the
registers are being accessed. Otherwise the device can be
on lower power mode.
This patch is based on a patch created by Kalle Jokiniemi:
https://patchwork.kernel.org/patch/618231/
which is itself based on a patch created by Atal
Shargorodsky: http://lkml.org/lkml/2009/3/10/266.
Signed-off-by: Paul Walmsley <paul@pwsan.com> Signed-off-by: Kalle Jokiniemi <kalle.jokiniemi@nokia.com> Tested-by: Kalle Jokiniemi <kalle.jokiniemi@nokia.com> Cc: Wim Van Sebroeck <wim@iguana.be> Acked-by: Wim Van Sebroeck <wim@iguana.be> Acked-by: Kevin Hilman <khilman@ti.com>
Paul Walmsley [Thu, 10 Mar 2011 10:50:09 +0000 (03:50 -0700)]
OMAP2+: clockdomain: add flag that will block autodeps from being added for a clockdomain
Add a new clockdomain flag, CLKDM_NO_AUTODEPS, which, when marked on a
clockdomain, will prevent "autodeps" from being associated with the
clockdomain. ("Autodeps" are sleep dependencies and wakeup
dependencies from/to processor modules that are automatically added to
a clockdomain when it is in hardware-supervised idle mode. They are
deprecated -- a relic from the old CDP trees -- but are still in use
for OMAP3.)
Also, prevent the hwmod code from adding or removing initiator
dependencies for clockdomains with this flag set.
This patch should allow others to test which clockdomains actually
still need autodeps.
Thanks to Kevin Hilman <khilman@ti.com> for noting that the original
version should also modify the hwmod code.
Signed-off-by: Paul Walmsley <paul@pwsan.com> Cc: Kevin Hilman <khilman@ti.com>
Create a new API that forms a wrapper to _set_module_autoidle()
to modify the AUTOIDLE bit.
This API is intended to be used by drivers that requires direct
manipulation of the AUTOIDLE bits in SYSCONFIG register.
McBSP driver requires autoidle bit to be enabled/disabled while
using sidetone feature.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Cc: Paul Walmsley <paul@pwsan.com> Cc: Benoit Cousson <b-cousson@ti.com>
[paul@pwsan.com: restrict the hwmod states that the autoidle bit can be changed
in; changed function name; dropped "int" from "unsigned int long"] Signed-off-by: Paul Walmsley <paul@pwsan.com>
To allow such boards to continue working normally, allow board file
maintainers to mark IP blocks to prevent them from being reset upon
init. This is done via a hwmod function, omap_hwmod_no_setup_reset().
Signed-off-by: Paul Walmsley <paul@pwsan.com> Cc: Michael Buesch <mb@bu3sch.de>
omar ramirez [Fri, 4 Mar 2011 20:32:44 +0000 (13:32 -0700)]
OMAP2+: hwmod: use status bit info for reset line
On OMAP2 and OMAP3 the reset ctrl shift doesn't match the
status bit, as it does on OMAP4, when handling the reset lines.
This patch adds a new member in the reset info structure, so now it
can be added as part of hwmod data, and checked accordingly for
OMAP2 or 3; otherwise, there could be cases when the shift masks
doesn't match both of the registers, and a successful reset might
throw an error message or vice versa.
Signed-off-by: Omar Ramirez Luna <omar.ramirez@ti.com>
[paul@pwsan.com: added a warning if st_shift used on OMAP4; renamed 'r'
variable; improved some documentation] Signed-off-by: Paul Walmsley <paul@pwsan.com>
Some of the omap2, omap3 peripherals support software reset. This
can be done through the softreset bit in sysconfig register.
The reset status can be checked through resetdone bit of
sysstatus register. syss_has_reset_status is added to the hwmod
database of peripherals which have resetdone bit in sysstatus register.
Cc: Rajendra Nayak <rnayak@ti.com> Cc: Paul Walmsley <paul@pwsan.com> Cc: Benoit Cousson <b-cousson@ti.com> Cc: Kevin Hilman <khilman@ti.com> Reviewed-by: Govindraj.R <govindraj.raja@ti.com> Signed-off-by: Avinash.H.M <avinashhm@ti.com> Signed-off-by: Paul Walmsley <paul@pwsan.com>
OMAP2+: hwmod: fix incorrect computation of autoidle_mask
Autoidle is a single bit, TIOCP_CFG[0], setting on OMAP1/2/3/4 platforms.
In _set_module_autoidle() I am seeing 0x3 value where the mask is computed.
This should be 0x1.
v2:
(1) Modified the subject.
(2) Modified the description with further specific information.
Benoit Cousson [Fri, 25 Feb 2011 16:46:33 +0000 (17:46 +0100)]
OMAP3: hwmod data: Remove masters port links for interconnects.
Master ports from interconnect are generating some annoying circular
references that become tricky to handle if we have to dynamically
remove some IP on some variant platforms.
Since they are not used for the moment, and since we can still build
that relation using the reverse relation (slave port from the IP
toward master port of the interconnect), let remove them for the
moment like it is done on OMAP4.
Commit d34427267186827dfd62bd8cf726601fffb22534 ("OMAP3: PM: Adding
smartreflex hwmod data") added data that claims that the L4 CORE has
two slave interfaces that originate from the SmartReflex modules,
omap3_l4_core__sr1 and omap3_l4_core__sr2. But as those two data
structure records show, it's L4 CORE that has a master port towards
SR1 and SR2.
Move the incorrect data from slaves list to master list.
Based on a path by Paul Walmsley <paul@pwsan.com>
https://patchwork.kernel.org/patch/623171/
That is based on a patch by Benoît Cousson <b-cousson@ti.com>:
Felipe Balbi [Thu, 10 Mar 2011 01:44:28 +0000 (18:44 -0700)]
OMAP: clock: fix compile warning
if building kernels without OMAP2 support, we
will see a warning such as:
arch/arm/mach-omap2/io.c: In function 'omap2_init_common_infrastructure':
arch/arm/mach-omap2/io.c:389:3: warning: statement with no effect
arch/arm/mach-omap2/io.c:391:3: warning: statement with no effect
Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Paul Walmsley <paul@pwsan.com>
Paul Walmsley [Fri, 4 Mar 2011 06:02:15 +0000 (06:02 +0000)]
OMAP2/3: VENC hwmod: add OCPIF_SWSUP_IDLE flag to interface
According to the hwmod interface data, the DSS submodule "VENC" uses a
clock, "dss_54m_fck"/"dss_tv_fck", which the PRCM cannot autoidle. By
default, the hwmod code assumes that interface clocks can be autoidled
by the PRCM. When the interface clock can't be autoidled by the PRCM,
those interfaces must be marked with the OCPIF_SWSUP_IDLE flag.
Otherwise, the "interface clock" will always have a non-zero use
count, and the device won't enter idle. This problem was observed on
N8x0.
Fix the immediate problem by marking the VENC interface with the
OCPIF_SWSUP_IDLE flag. But it's not clear that
"dss_54m_fck"/"dss_tv_fck" is really the correct interface clock for
VENC. It may be that the VENC interface should use a
hardware-autoidling interface clock. This is the situation on OMAP4,
which uses "l3_div_ck" as the VENC interface clock, which can be
autoidled by the PRCM. Clarification from TI is needed.
Problem found and patch tested on N8x0 by Tony Lindgren
<tony@atomide.com>.
Signed-off-by: Paul Walmsley <paul@pwsan.com> Cc: Tony Lindgren <tony@atomide.com> Cc: Senthilvadivu Guruswamy <svadivu@ti.com> Cc: Sumit Semwal <sumit.semwal@ti.com> Cc: Kevin Hilman <khilman@ti.com> Cc: Benoît Cousson <b-cousson@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
The driver provides the information regarding the ocp errors
that gets logged in the interconnect. The error information
gives the detail regarding the target that was attempted
to be accessed and its corresponding address.
The driver provides the information regarding the ocp errors
that gets logged in the interconnect.The error info provides
the details regarding the master or the target that
generated the error, type of error and the corresponding address.
The stack dump is also provided.
Signed-off-by: sricharan <r.sricharan@ti.com>
[r.sricharan@ti.com: Enhacements, major cleanup and made it functional] Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
[santosh.shilimkar@ti.com: Driver design changes as per OMAP4 version] Signed-off-by: Felipe Balbi <balbi@ti.com>
[balbi@ti.com: Initial version of the driver] Acked-by: Benoit Cousson <b-cousson@ti.com>
CC arch/arm/mach-omap1/mcbsp.o
arch/arm/mach-omap1/mcbsp.c: In function 'omap1_mcbsp_init':
arch/arm/mach-omap1/mcbsp.c:384: warning: dereferencing 'void *' pointer
arch/arm/mach-omap1/mcbsp.c:387: error: invalid use of void expression
arch/arm/mach-omap1/mcbsp.c:390: warning: dereferencing 'void *' pointer
arch/arm/mach-omap1/mcbsp.c:393: error: invalid use of void expression
Fix by avoiding NULL dereferences.
Signed-off-by: Paul Walmsley <paul@pwsan.com> Cc: Kishon Vijay Abraham I <kishon@ti.com> Cc: Tony Lindgren <tony@atomide.com> Acked-by: Jarkko Nikula <jhnikula@gmail.com>
[tony@atomide.com: updated description not to remove unnecessary branch name] Signed-off-by: Tony Lindgren <tony@atomide.com>
Sanjeev Premi [Fri, 11 Feb 2011 09:05:00 +0000 (09:05 +0000)]
omap2/3: clockdomains: fix compile-time warnings
This patch fixes these warnings when building kernel for OMAP3EVM
only.
CC arch/arm/mach-omap2/clockdomains2xxx_3xxx_data.o
arch/arm/mach-omap2/clockdomains2xxx_3xxx_data.c:95: warning:
'dsp_24xx_wkdeps' defined but not used
arch/arm/mach-omap2/clockdomains2xxx_3xxx_data.c:119: warning:
'mpu_24xx_wkdeps' defined but not used
arch/arm/mach-omap2/clockdomains2xxx_3xxx_data.c:147: warning:
'core_24xx_wkdeps' defined but not used
The problem should be noticed when building for other OMAP3
platforms (only) as well.
Signed-off-by: Sanjeev Premi <premi@ti.com> Signed-off-by: Paul Walmsley <paul@pwsan.com>
Paul Walmsley [Fri, 25 Feb 2011 22:52:04 +0000 (15:52 -0700)]
OMAP2xxx: clock: remove dsp_irate_ick
After commit 81b34fbecbfbf24ed95c2d80d5cb14149652408f ("OMAP2 clock:
split OMAP2420, OMAP2430 clock data into their own files"), it's
possible to remove dsp_irate_ick from the OMAP2420 and OMAP2430 clock
files. It was originally only needed due to a 2420/2430 clock tree difference,
and now that the data is in separate files, it's superfluous.
Paul Walmsley [Wed, 16 Feb 2011 22:38:39 +0000 (15:38 -0700)]
OMAP2+: clock: remove the DPLL rate tolerance code
Remove the DPLL rate tolerance code that is called during rate
rounding. As far as I know, this code is never used, since it's been
more important for callers of the DPLL round_rate()/set_rate()
functions to obtain an exact rate than it is to save a relatively
small amount of power.
Paul Walmsley [Wed, 16 Feb 2011 22:38:38 +0000 (15:38 -0700)]
OMAP: clock: bail out early if arch_clock functions not implemented
Bail out before we take the clockfw_lock spinlock if the corresponding
OMAP1 or OMAP2+ clock function is not defined. The intention is to
reduce and simplify the work that is done inside the spinlock.
Paul Walmsley [Wed, 16 Feb 2011 22:38:38 +0000 (15:38 -0700)]
OMAP2xxx: clock: fix interface clocks and clockdomains for modules in the WKUP domain
The parent of the interface clocks for GPTIMER1, MPU_WDT,
SYNCTIMER_32K, SCM, WDT1, and the ICR (2430 only) were all listed as
being l4_ck. This isn't accurate; these modules exist inside the WKUP
domain, and the interface clock to these modules runs at the SYS_CLK
rate rather than the CORE L4 rate.
So, create a new clock "wu_l4_ick", similar to the OMAP3
"wkup_l4_ick", that serves as the parent for these clocks.
Also, these clocks were listed as existing inside core_l4_clkdm;
wkup_clkdm is probably more accurate.
The OMAP2420/2430 external 32-kHz low-frequency oscillator is a 32768
Hz oscillator, not a 32,000 Hz oscillator[1][2]. Fix this in the clock
tree.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
1. OMAP2420/22 Multimedia Processor Data Manual, Version P [SWPS019P],
section 5.1.4 "External 32-kHz CMOS Clock" (note that it refers to
a "32.768-kHz" clock; this presumably should be "32.768-KHz")
2. OMAP2430 Multimedia Processor ES2.1 Data Manual, Version V [SWPS023V],
section 5.1.4 "External 32-kHz CMOS Clock" (note that it refers to
a "32.768-kHz" clock; this presumably should be "32.768-KHz")
Paul Walmsley [Fri, 25 Feb 2011 22:39:30 +0000 (15:39 -0700)]
OMAP2/3: PM: remove manual CM_AUTOIDLE bit setting in mach-omap2/pm*xx.c
These CM_AUTOIDLE bits are now set by the clock code via the common PM
code in mach-omap2/pm.c.
N.B.: The pm24xx.c code that this patch removes didn't ensure that the
CM_AUTOIDLE bits were set for several 2430-only modules, such as
GPIO5, MDM_INTC, MMCHS1/2, the modem oscillator clock, and USBHS.
Similarly, the pm34xx.c code that this patch removes didn't ensure
that the CM_AUTOIDLE bits were set for USIM and the AM3517 UART4.
Those cases should now be handled.
Signed-off-by: Paul Walmsley <paul@pwsan.com> Cc: Kevin Hilman <khilman@ti.com> Tested-by: Rajendra Nayak <rnayak@ti.com> Reviewed-by: Kevin Hilman <khilman@ti.com>
Paul Walmsley [Fri, 25 Feb 2011 22:39:30 +0000 (15:39 -0700)]
OMAP3: clock: use autoidle clkops for all autoidle-controllable interface clocks
Mark each interface clock with a corresponding CM_AUTOIDLE bit with
a clkops that has the allow_idle/deny_idle function pointers populated.
This allows the OMAP clock framework to enable and disable autoidle for
these clocks.
Signed-off-by: Paul Walmsley <paul@pwsan.com> Tested-by: Rajendra Nayak <rnayak@ti.com> Reviewed-by: Kevin Hilman <khilman@ti.com>
Paul Walmsley [Fri, 25 Feb 2011 22:39:30 +0000 (15:39 -0700)]
OMAP2430: clock: use autoidle clkops for all autoidle-controllable interface clocks
Mark each interface clock with a corresponding CM_AUTOIDLE bit with
a clkops that has the allow_idle/deny_idle function pointers populated.
This allows the OMAP clock framework to enable and disable autoidle for
these clocks.
Signed-off-by: Paul Walmsley <paul@pwsan.com> Tested-by: Rajendra Nayak <rnayak@ti.com> Reviewed-by: Kevin Hilman <khilman@ti.com>
Paul Walmsley [Fri, 25 Feb 2011 22:39:29 +0000 (15:39 -0700)]
OMAP2420: clock: use autoidle clkops for all autoidle-controllable interface clocks
Mark each interface clock with a corresponding CM_AUTOIDLE bit with
a clkops that has the allow_idle/deny_idle function pointers populated.
This allows the OMAP clock framework to enable and disable autoidle for
these clocks.
Signed-off-by: Paul Walmsley <paul@pwsan.com> Tested-by: Rajendra Nayak <rnayak@ti.com> Reviewed-by: Kevin Hilman <khilman@ti.com>
Paul Walmsley [Fri, 25 Feb 2011 22:39:28 +0000 (15:39 -0700)]
OMAP2+: clock: add interface clock type code with autoidle support
Add interface clock type code with autoidle enable/disable support.
The clkops structures created in this file will be used for all
OMAP2/3 interface clocks with autoidle support. They will enable the
clock framework to control interface clock autoidle directly.
Signed-off-by: Paul Walmsley <paul@pwsan.com> Tested-by: Rajendra Nayak <rnayak@ti.com> Reviewed-by: Kevin Hilman <khilman@ti.com>
Paul Walmsley [Fri, 25 Feb 2011 22:39:27 +0000 (15:39 -0700)]
OMAP2+: clock: comment that osc_ck/osc_sys_ck should use clockfw autoidle control
Place some comments in the OMAP oscillator clock control code to note that
its autoidle mode should eventually be controlled via the new OMAP clockfw
autoidle control interface.
Signed-off-by: Paul Walmsley <paul@pwsan.com> Tested-by: Rajendra Nayak <rnayak@ti.com> Reviewed-by: Kevin Hilman <khilman@ti.com>
Paul Walmsley [Fri, 25 Feb 2011 22:39:27 +0000 (15:39 -0700)]
OMAP2xxx: clock: add clockfw autoidle support for APLLs
OMAP2xxx devices have two on-chip APLLs. These APLLs can
automatically enter idle when not in use. Connect the APLL autoidle
code to the clock code, so that the clock framework can handle this
process. As part of this patch, remove the code in mach-omap2/pm24xx.c
that previously handled APLL autoidle control.
Signed-off-by: Paul Walmsley <paul@pwsan.com> Cc: Kevin Hilman <khilman@ti.com> Tested-by: Rajendra Nayak <rnayak@ti.com> Reviewed-by: Kevin Hilman <khilman@ti.com>
Paul Walmsley [Fri, 25 Feb 2011 22:49:53 +0000 (15:49 -0700)]
OMAP2: clock: add DPLL autoidle support
Add the necessary code and data to allow the clock framework to enable
and disable the OMAP2 DPLL autoidle state. This is so the direct
register access can be moved out of the mach-omap2/pm24xx.c code, and other
code that needs to control this (e.g., CPUIdle) can do so via an API.
As part of this patch, remove the pm24xx.c code that formerly wrote
directly to the autoidle bits.
Signed-off-by: Paul Walmsley <paul@pwsan.com> Cc: Kevin Hilman <khilman@ti.com> Tested-by: Rajendra Nayak <rnayak@ti.com> Reviewed-by: Kevin Hilman <khilman@ti.com>
Some drivers wish to know whether the device that they control can
ever lose context, for example, when the device's enclosing
powerdomain loses power. They can use this information to determine
whether it is necessary to save and restore device context, or whether
it can be skipped. Implement the powerdomain portion of this by
adding the function pwrdm_can_ever_lose_context(). This is not for
use directly from driver code, but instead is intended to be called
from driver-subarch integration code (i.e., arch/arm/*omap* code).
Currently, the result from this function should be passed into the
driver code via struct platform_data, but at some point this should
be part of some common or OMAP-specific device code.
Paul Walmsley [Tue, 8 Mar 2011 02:28:15 +0000 (19:28 -0700)]
OMAP2+: powerdomain: fix bank power state bitfields
The bank power state bitfields in the powerdomain data are
encoded incorrectly. These fields are intended to be bitfields,
representing a set of power states that the memory banks support.
However, when only one power state was supported by a given bank,
the field was incorrectly set to the bit shift -- not the mask.
While here, update some file copyrights.
The OMAP4 autogeneration scripts have been updated accordingly.
Paul Walmsley [Tue, 8 Mar 2011 02:28:15 +0000 (19:28 -0700)]
OMAP2/3: WKUP powerdomain: mark as being always on
Mark the WKUP powerdomain as being always on -- at least, as long as the
chip has power. This will be used to enable the powerdomain code to
determine whether a given powerdomain is ever able to power off. While
here, update the file copyright.
Ilkka Koskinen [Wed, 2 Mar 2011 13:24:06 +0000 (13:24 +0000)]
mfd: twl4030_codec: Remove unused and duplicate audio_mclk fields
audio_mclk can be queried from mfd driver. Therefore, it is not
needed in twl4030_codec_audio_data or in twl4030_codec_vibra_data
anymore.
Signed-off-by: Ilkka Koskinen <ilkka.koskinen@nokia.com> Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Samuel Ortiz <sameo@linux.intel.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Ilkka Koskinen [Wed, 2 Mar 2011 13:24:05 +0000 (13:24 +0000)]
omap: Remove unnecessary twl4030_codec_audio settings from board files
twl4030_codec_audio and twl4030_codec_vibra_data has unused field.
In order to remove it, corresponding settings needs to be removed
from board files.
Signed-off-by: Ilkka Koskinen <ilkka.koskinen@nokia.com> Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Tony Lindgren [Thu, 24 Feb 2011 12:56:42 +0000 (12:56 +0000)]
ldp: Fix regulator mapping for ads7846 TS controller
On the OMAP3430LDP board, the ads7846 touchscreen controller
is powered by VAUX1 regulator (supplying 3.0v).
Fix this mapping in the board file, and hence prevent
the ads7846 driver init to fail with the below error..
ads7846 spi1.0: unable to get regulator: -19
Signed-off-by: Rajendra Nayak <rnayak@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Ming Lei [Wed, 2 Mar 2011 22:41:46 +0000 (06:41 +0800)]
arm: omap: fix section mismatch warning
WARNING: arch/arm/plat-omap/built-in.o(.data+0x6d4): Section mismatch in reference from the variable omap_driver to the function .init.text:omap_cpu_init()
The variable omap_driver references
the function __init omap_cpu_init()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
Signed-off-by: Ming Lei <tom.leiming@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Paul Walmsley [Sat, 26 Feb 2011 01:22:08 +0000 (18:22 -0700)]
MMC: omap_hsmmc: enable interface clock before calling mmc_host_enable()
The code path entered via mmc_host_enable() can include register
accesses to the HSMMC IP block. For this to work, both the device
interface clock and functional clock need to be enabled before
mmc_host_enable() is called. However, omap_hsmmc_probe() calls
mmc_host_enable() before enabling the device interface clock.
Fix by calling mmc_host_enable() after the device interface clock is
enabled.
Signed-off-by: Paul Walmsley <paul@pwsan.com> Cc: Madhusudhan Chikkature Rajashekar <madhu.cr@ti.com> Cc: Adrian Hunter <adrian.hunter@nokia.com> Cc: Kishore Kadiyala <kishore.kadiyala@ti.com> Cc: Tero Kristo <Tero.Kristo@nokia.com> Acked-by: Madhusudhan Chikkature Rajashekar <madhu.cr@ti.com>
Rajendra Nayak [Fri, 25 Feb 2011 22:40:21 +0000 (15:40 -0700)]
OMAP2+: omap_device/clock: Do not expect an entry in clkdev for opt_clks
The _add_optional_clock_alias function expects an entry
already existing in the clkdev table in the form of
<dev-id=NULL, con-id=role> which might not be the case
always.
Instead, just check if an entry already exists in clkdev
in the <dev-id=dev_name, con-id=role> form, else go ahead
and add one.
Remove any assumption of an entry already existing in clkdev
table in any form.
Since this means, adding a new entry in clkdev if it does
not already exist, and not really adding an 'alias',
also rename the function name
(s/_add_optional_clock_alias/_add_optional_clock_clkdev)
to reflect this.
omap4: powerdomain: Use intended PWRSTS_* flags instead of values
IVAHD and ABE power domain logic state is populated using directly
value instead of the capability flags.
Fix the same.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
[paul@pwsan.com: updated to apply at a different point on the tree] Signed-off-by: Paul Walmsley <paul@pwsan.com>
"TPM is working for me so I can log into employer's network in 2.6.37.
It broke when I tried 2.6.38-rc6, with the following relevant lines
from my dmesg:
This caused me to get suspicious, especially since the _other_ TPM
commit in 2.6.38 had already been reverted, so I tried reverting
commit c4ff4b829e: "TPM: Long default timeout fix". With this commit
reverted, my TPM on my Lenovo T410 is once again working."
Kishore Kadiyala [Mon, 28 Feb 2011 15:18:04 +0000 (20:48 +0530)]
OMAP: adapt hsmmc to hwmod framework
OMAP2420 platform consists of mmc block as in omap1 and not the
hsmmc block as present in omap2430, omap3, omap4 platforms.
Removing all base address macro defines except keeping one for OMAP2420 and
adapting only hsmmc device registration and driver to hwmod framework.
Changes involves:
1) Remove controller reset in devices.c which is taken care of
by hwmod framework.
2) Using omap-device layer to register device and utilizing data from
hwmod data file for base address, dma channel number, Irq_number,
device attribute.
3) Update the driver to use dev_attr to find whether controller
supports dual volt cards
Signed-off-by: Paul Walmsley <paul@pwsan.com> Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com> Reviewed-by: Balaji T K <balajitk@ti.com> Cc: Benoit Cousson <b-cousson@ti.com> CC: Kevin Hilman <khilman@deeprootsystems.com> Cc: Tony Lindgren <tony@atomide.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Kishore Kadiyala [Mon, 28 Feb 2011 15:18:03 +0000 (20:48 +0530)]
OMAP: hsmmc: Move mux configuration to hsmmc.c
Moving the definition of mux setting API from devices.c to hsmmc.c
and renaming it from "omap2_mmc_mux" to "omap_hsmmc_mux".
Also calling "omap_hsmmc_mux" from omap2_hsmmc_init.
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com> Cc: Chris Ball <cjb@laptop.org Cc: Tony Lindgren <tony@atomide.com Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP: hwmod data: Add dev_attr and use in the host driver
Add a device attribute to hwmod data of omap2430, omap3, omap4.
Currently the device attribute holds information regarding dual volt MMC card
support by the controller which will be later passed to the host driver via
platform data.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com> Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com> Acked-by: Benoit Cousson<b-cousson@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Anand Gadiyar [Tue, 1 Mar 2011 21:12:55 +0000 (13:12 -0800)]
omap: mmc: split out init for 2420
The MMC controller on the OMAP2420 is different from those
on the OMAP2430, OMAP3 and OMAP4 families - all of the latter
are identical. The one on the OMAP2420 is closer to that
on OMAP1 chips.
Currently, the n8x0 is the only OMAP2420 platform supported
in mainline which registers the MMC controller. Upcoming
changes to register the controllers using hwmod data are
potentially invasive. To reduce the risk, separate out the
2420 controller registration from the common init function
and update its only user. Also seperating out mux settings
for OMAP2420.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com> Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com> Cc: Tony Lindgren <tony@atomide.com> Cc: Madhusudhan Chikkature <madhu.cr@ti.com> Cc: Chris Ball <cjb@laptop.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
Eyal Reizer [Sun, 27 Feb 2011 10:45:18 +0000 (10:45 +0000)]
omap: omap3evm: add support for the WL12xx WLAN module to the omap3evm
This patch is again current omap-for-linus branch
Adds platform initialization for working with the WLAN module
attached to the omap3evm.
The patch includes MMC2 initialization, SDIO and control pins
muxing and platform device registration.
Signed-off-by: Eyal Reizer <eyalr@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Several ACPI drivers fail to build if CONFIG_NET is unset, because
they refer to things depending on CONFIG_THERMAL that in turn depends
on CONFIG_NET. However, CONFIG_THERMAL doesn't really need to depend
on CONFIG_NET, because the only part of it requiring CONFIG_NET is
the netlink interface in thermal_sys.c.
Put the netlink interface in thermal_sys.c under #ifdef CONFIG_NET
and remove the dependency of CONFIG_THERMAL on CONFIG_NET from
drivers/thermal/Kconfig.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Acked-by: Randy Dunlap <randy.dunlap@oracle.com> Cc: Ingo Molnar <mingo@elte.hu> Cc: Len Brown <lenb@kernel.org> Cc: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Luming Yu <luming.yu@intel.com> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Tue, 1 Mar 2011 01:58:09 +0000 (17:58 -0800)]
Merge branch 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm: fix unsigned vs signed comparison issue in modeset ctl ioctl.
drm/nv50-nvc0: make sure vma is definitely unmapped when destroying bo
Linus Torvalds [Tue, 1 Mar 2011 01:55:08 +0000 (17:55 -0800)]
Merge branches 'perf-fixes-for-linus', 'x86-fixes-for-linus' and 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf timechart: Fix max number of cpus
perf timechart: Fix black idle boxes in the title
perf hists: Print number of samples, not the period sum
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Use u32 instead of long to set reset vector back to 0
* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
clockevents: Prevent oneshot mode when broadcast device is periodic
Linus Torvalds [Tue, 1 Mar 2011 01:53:04 +0000 (17:53 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
fuse: fix truncate after open
fuse: fix hang of single threaded fuseblk filesystem
Paul Walmsley [Sat, 26 Feb 2011 00:38:25 +0000 (17:38 -0700)]
OMAP2+: sdrc: fix compile break on OMAP4-only config on current omap-for-linus
On non-OMAP2 and non-OMAP3 kernel configs, turn omap2_sdrc_init() into
a no-op. Otherwise, compilation breaks on an OMAP4-only config with
the current omap-for-linus branch:
arch/arm/mach-omap2/built-in.o: In function `omap2_init_common_devices':
../mach-omap2/io.c:421: undefined reference to `omap2_sdrc_init'
Thanks to Sergei Shtylyov <sshtylyov@mvista.com> for suggesting the use
of a empty static inline function rather than a macro.
Signed-off-by: Paul Walmsley <paul@pwsan.com> Cc: Tony Lindgren <tony@atomide.com> Cc: Sergei Shtylyov <sshtylyov@mvista.com>
[tony@atomide.com: updated not to use __init for inline omap2_sdrc_init] Signed-off-by: Tony Lindgren <tony@atomide.com>
Linus Torvalds [Tue, 1 Mar 2011 01:52:47 +0000 (17:52 -0800)]
Merge branch 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jlbec/ocfs2
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jlbec/ocfs2:
ocfs2: Check heartbeat mode for kernel stacks only
Ocfs2/refcounttree: Fix a bug for refcounttree to writeback clusters in a right number.
ocfs2: Fix estimate of necessary credits for mkdir
Linus Torvalds [Tue, 1 Mar 2011 01:47:09 +0000 (17:47 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
eukrea-tlv320: fix platform_name
ASoC: correct pxa AC97 DAI names
ALSA: hda - Add support for new IDT 92HD98 and 92HD99 codecs
ALSA: HDA: Add ideapad quirk for two Dell machines
ALSA: HDA: Add a new Conexant codec 506e (20590)
ALSA: usb-audio: fix oops due to cleanup race when disconnecting
ASoC: Hook wm_hubs micbiases up to CLK_SYS
ASoC: Correct definition of WM8903_VMID_RES_5K
ASoC: Fix WM8958 default microphone detection argument ordering
ALSA: HDA: Fix mic initialization in VIA auto parser
ALSA: fix one memory leak in sound jack
Ben Hutchings [Sun, 27 Feb 2011 05:41:35 +0000 (05:41 +0000)]
mm: <asm-generic/pgtable.h> must include <linux/mm_types.h>
Commit e2cda3226481 ("thp: add pmd mangling generic functions") replaced
some macros in <asm-generic/pgtable.h> with inline functions.
If the functions are to be defined (not all architectures need them)
then struct vm_area_struct must be defined first. So include
<linux/mm_types.h>.
Fixes a build failure seen in Debian:
CC [M] drivers/media/dvb/mantis/mantis_pci.o
In file included from arch/arm/include/asm/pgtable.h:460,
from drivers/media/dvb/mantis/mantis_pci.c:25:
include/asm-generic/pgtable.h: In function 'ptep_test_and_clear_young':
include/asm-generic/pgtable.h:29: error: dereferencing pointer to incomplete type
Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Paul Walmsley [Wed, 23 Feb 2011 07:14:08 +0000 (00:14 -0700)]
OMAP2+: clockevent: set up GPTIMER clockevent hwmod right before timer init
Set up the GPTIMER hwmod used for the clockevent source immediately
before it is used. This avoids the need to set up all of the hwmods
until the boot process is further along. (In general, we want to defer
as much as possible until late in the boot process.)
This second version fixes a bug pointed out by Santosh Shilimkar
<santosh.shilimkar@ti.com>, that would cause the kernel to use an
incorrect timer hwmod name if the selected GPTIMER was not 1 or 12 -
thanks Santosh. Also, Tarun Kanti DebBarma <tarun.kanti@ti.com>
pointed out that the original patch did not apply cleanly; this has
now been fixed.
Signed-off-by: Paul Walmsley <paul@pwsan.com> Cc: Benoît Cousson <b-cousson@ti.com> Cc: Tony Lindgren <tony@atomide.com> Cc: Kevin Hilman <khilman@ti.com> Cc: Santosh Shilimkar <santosh.shilimkar@ti.com> Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com> Cc: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Paul Walmsley [Wed, 23 Feb 2011 07:14:07 +0000 (00:14 -0700)]
OMAP2+: hwmod: add ability to setup individual hwmods
Add omap_hwmod_setup_one(), which is intended for use early in boot to
selectively setup the hwmods needed for system clocksources and
clockevents, and any other hwmod that is needed in early boot.
omap_hwmod_setup_all() can then be called later in the boot process.
The point is to minimize the amount of code that needs to be run
early.
Signed-off-by: Paul Walmsley <paul@pwsan.com> Cc: Benoît Cousson <b-cousson@ti.com> Cc: Kevin Hilman <khilman@ti.com> Cc: Santosh Shilimkar <santosh.shilimkar@ti.com> Cc: Tony Lindgren <tony@atomide.com>
Paul Walmsley [Wed, 23 Feb 2011 07:14:07 +0000 (00:14 -0700)]
OMAP2+: hwmod: ignore attempts to re-setup a hwmod
Previously, if a hwmod had already been set up, and the code attempted
to set up the hwmod again, an error would be returned. This is not
really useful behavior if we wish to allow the OMAP core code to setup
the hwmods needed for the Linux clocksources and clockevents before
the rest of the hwmods are setup. So, instead of generating errors,
just ignore the attempt to re-setup the hwmod.
Signed-off-by: Paul Walmsley <paul@pwsan.com> Cc: Benoît Cousson <b-cousson@ti.com> Cc: Kevin Hilman <khilman@ti.com>
Paul Walmsley [Wed, 23 Feb 2011 07:14:06 +0000 (00:14 -0700)]
OMAP2+: hwmod: find MPU initiator hwmod during in _register()
Move the code that looks for the MPU initiator hwmod to run during
the individual hwmod _register() function. (Previously, it ran after
all hwmods were registered in the omap_hwmod_late_init() function.)
This is done so code can late-initialize a few individual hwmods --
for example, for the system timer -- before the entire set of hwmods is
initialized later in boot via omap_hwmod_late_init().
Signed-off-by: Paul Walmsley <paul@pwsan.com> Cc: Benoît Cousson <b-cousson@ti.com> Cc: Kevin Hilman <khilman@ti.com>
Paul Walmsley [Mon, 28 Feb 2011 18:58:14 +0000 (11:58 -0700)]
OMAP2+: hwmod: rename some init functions
Rename omap_hwmod_init() to omap_hwmod_register(). Rename
omap_hwmod_late_init() to omap_hwmod_setup_all(). Also change all of
the callers to reflect the new names. While here, update some
copyrights.
Suggested by Tony Lindgren <tony@atomide.com>.
N.B. The comment in mach-omap2/serial.c may no longer be correct, given
recent changes in init order.
Signed-off-by: Paul Walmsley <paul@pwsan.com> Cc: Benoît Cousson <b-cousson@ti.com> Cc: Kevin Hilman <khilman@ti.com> Cc: Tony Lindgren <tony@atomide.com>
Paul Walmsley [Wed, 23 Feb 2011 07:14:06 +0000 (00:14 -0700)]
OMAP2+: hwmod: allow multiple calls to omap_hwmod_init()
There's no longer any reason why we should prevent multiple
calls to omap_hwmod_init(). It is now simply used to register an
array of hwmods.
This should allow a subset of hwmods (e.g., hwmods
handling the system clocksource and clockevents) to be registered
earlier than the remaining mass of hwmods.
Signed-off-by: Paul Walmsley <paul@pwsan.com> Cc: Benoît Cousson <b-cousson@ti.com> Cc: Kevin Hilman <khilman@ti.com>
Don Zickus [Tue, 8 Feb 2011 04:25:00 +0000 (23:25 -0500)]
x86: Use u32 instead of long to set reset vector back to 0
A customer of ours, complained that when setting the reset
vector back to 0, it trashed other data and hung their box.
They noticed when only 4 bytes were set to 0 instead of 8,
everything worked correctly.
Mathew pointed out:
|
| We're supposed to be resetting trampoline_phys_low and
| trampoline_phys_high here, which are two 16-bit values.
| Writing 64 bits is definitely going to overwrite space
| that we're not supposed to be touching.
|
So limit the area modified to u32.
Signed-off-by: Don Zickus <dzickus@redhat.com> Acked-by: Matthew Garrett <mjg@redhat.com> Cc: <stable@kernel.org>
LKML-Reference: <1297139100-424-1-git-send-email-dzickus@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Thomas Renninger [Sun, 27 Feb 2011 21:36:46 +0000 (22:36 +0100)]
perf timechart: Fix max number of cpus
Currently numcpus is determined in pid_put_sample which is only
called on sched_switch/sched_wakeup sample processing.
On a machine with a lot cpus I often saw the last cpu missing.
Check for (max) numcpus on every event happening and in the
beginning. -> fixes the issue for me.
Signed-off-by: Thomas Renninger <trenn@suse.de> Cc: Arjan van de Ven <arjan@linux.intel.com> Cc: Arnaldo Carvalho de Melo <acme@ghostprotocols.net> Cc: lenb@kernel.org
LKML-Reference: <1298842606-55712-6-git-send-email-trenn@suse.de> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Thomas Renninger [Sun, 27 Feb 2011 21:36:45 +0000 (22:36 +0100)]
perf timechart: Fix black idle boxes in the title
This fix is needed for eye of gnome and firefox svg viewers.
Only Inkscape can handle the broken case.
Compare with the other svg_legenda_box declarations, looks
like a typo slipped in at this place.
Signed-off-by: Thomas Renninger <trenn@suse.de> Cc: Arjan van de Ven <arjan@linux.intel.com> Cc: Arnaldo Carvalho de Melo <acme@ghostprotocols.net> Cc: lenb@kernel.org
LKML-Reference: <1298842606-55712-5-git-send-email-trenn@suse.de> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Ben Skeggs [Mon, 28 Feb 2011 04:22:12 +0000 (14:22 +1000)]
drm/nv50-nvc0: make sure vma is definitely unmapped when destroying bo
Somehow fixes a misrendering + hang at GDM startup on my NVA8...
My first guess would have been stale TLB entries laying around that a new
bo then accidentally inherits. That doesn't make a great deal of sense
however, as when we mapped the pages for the new bo the TLBs would've
gotten flushed anyway.