Mengdong Lin [Thu, 20 Mar 2014 05:01:06 +0000 (13:01 +0800)]
ALSA: hda - verify pin:cvt connection on preparing a stream for Intel HDMI codec
This is a temporary fix for some Intel HDMI codecs to avoid no sound output for
a resuming playback after S3.
After S3, the audio driver restores pin:cvt connection selections by
snd_hda_codec_resume_cache(). However this can happen before the gfx side is
ready and such connect selection is overlooked by HW. After gfx is ready, the
pins make the default selection again. And this will cause multiple pins share
a same convertor and mute control will affect each other. Thus a resumed audio
playback become silent after S3.
This patch verifies pin:cvt connection on preparing a stream, to assure the pin
selects the right convetor and an assigned convertor is not shared by other
unused pins. Apply this fix-up on Haswell, Broadwell and Valleyview (Baytrail).
We need this temporary fix before a reliable software communication channel is
established between audio and gfx, to sync audio/gfx operations.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Kailang Yang [Tue, 18 Mar 2014 08:45:32 +0000 (16:45 +0800)]
ALSA: hda/realtek - Restore default value for ALC282
Restore the registers to prevent the abnormal digital power supply
rising ratio/sequence to the codec and causing the incorrect default
codec register restoration during initialization.
Signed-off-by: Kailang Yang <kailang@realtek.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Kailang Yang [Tue, 18 Mar 2014 08:15:54 +0000 (16:15 +0800)]
ALSA: hda/realtek - Fix the noise after suspend and resume on ALC282 codec
When the power state of ALC283 codec goes to D3 or return back to D0,
it gives a noise via headphone output. To follow the depop procedure,
it will be better.
Signed-off-by: Kailang Yang <kailang@realtek.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Kailang Yang [Mon, 17 Mar 2014 05:51:27 +0000 (13:51 +0800)]
ALSA: hda/realtek - Restore default value for ALC283
Restore the registers to prevent the abnormal digital power supply
rising ratio/sequence to the codec and causing the incorrect default
codec register restoration during initialization.
Takashi Iwai [Thu, 13 Mar 2014 18:04:24 +0000 (19:04 +0100)]
Merge tag 'tlv320aic31xx-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Fixes for tlv320aic31xx
A few fixes for issues not yet identified by the zero day tester due to
the last pull request being rushed in order to clean up the problem with
the git mismerge.
Takashi Iwai [Thu, 13 Mar 2014 18:03:48 +0000 (19:03 +0100)]
Merge tag 'asoc-v3.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Updates for v3.15
This is mostly a few additional fixes from Lars-Peter, a new driver and
cleaning up a git failure with merging the Intel branch (combined with
an xargs failure to pay attention to error codes). The history lists a
bunch of additional commits for the branch but the content of those
commits is actually present already but not recorded in history due to
git failing. Unfortunately xargs is used in the merge script and it
doesn't do a good job of noticing errors from the commands it invokes.
Remove snd_soc_codec_set_cache_io(codec, 8, 8, SND_SOC_REGMAP) call
and codec->control_data = aic31xx->regmap assignment since that
already done by core.
Signed-off-by: Jyri Sarha <jsarha@ti.com> Signed-off-by: Mark Brown <broonie@linaro.org>
Mark Brown [Thu, 13 Mar 2014 14:19:00 +0000 (14:19 +0000)]
Merge tag 'asoc-v3.15' into asoc-next
ASoC: Updates for v3.15
Quite a busy release for ASoC this time, more on janitorial work than
exciting new features but welcome nontheless:
- Lots of cleanups from Takashi for enumerations; the original API for
these was error prone so he's refactored lots of code to use more
modern APIs which avoid issues.
- Elimination of the ASoC level wrappers for I2C and SPI moving us
closer to converting to regmap completely and avoiding some
randconfig hassle.
- Provide both manually and transparently locked DAPM APIs rather than
a mix of the two fixing some concurrency issues.
- Start converting CODEC drivers to use separate bus interface drivers
rather than having them all in one file helping avoid dependency
issues.
- DPCM support for Intel Haswell and Bay Trail platforms.
- Lots of work on improvements for simple-card, DaVinci and the Renesas
rcar drivers.
- New drivers for Analog Devices ADAU1977, TI PCM512x and parts of the
CSR SiRF SoC.
# gpg: Signature made Wed 12 Mar 2014 23:05:45 GMT using RSA key ID 7EA229BD
# gpg: Good signature from "Mark Brown <broonie@sirena.org.uk>"
# gpg: aka "Mark Brown <broonie@debian.org>"
# gpg: aka "Mark Brown <broonie@kernel.org>"
# gpg: aka "Mark Brown <broonie@tardis.ed.ac.uk>"
# gpg: aka "Mark Brown <broonie@linaro.org>"
# gpg: aka "Mark Brown <Mark.Brown@linaro.org>"
Mark Brown [Thu, 13 Mar 2014 14:18:58 +0000 (14:18 +0000)]
Merge tag 'asoc-v3.14-rc6' into asoc-linus
ASoC: Fixes for v3.14
A few things here:
- Avoid memory leaks in error cases with DPCM, this code has never been
that well tested in mainline due to the lack of mainline drivers but
we now have one queued for the merge window!
- Fix the N810 audio driver to load when booted with DT since the
platform was converted to DT during the merge window.
- Fixes for initialisation of some MFD drivers that are probably unused
in mainline
# gpg: Signature made Mon 10 Mar 2014 18:21:32 GMT using RSA key ID 7EA229BD
# gpg: Good signature from "Mark Brown <broonie@sirena.org.uk>"
# gpg: aka "Mark Brown <broonie@debian.org>"
# gpg: aka "Mark Brown <broonie@kernel.org>"
# gpg: aka "Mark Brown <broonie@tardis.ed.ac.uk>"
# gpg: aka "Mark Brown <broonie@linaro.org>"
# gpg: aka "Mark Brown <Mark.Brown@linaro.org>"
Mark Brown [Thu, 13 Mar 2014 14:16:35 +0000 (14:16 +0000)]
Merge tag 'asoc-v3.15' into asoc-intel
ASoC: Updates for v3.15
Quite a busy release for ASoC this time, more on janitorial work than
exciting new features but welcome nontheless:
- Lots of cleanups from Takashi for enumerations; the original API for
these was error prone so he's refactored lots of code to use more
modern APIs which avoid issues.
- Elimination of the ASoC level wrappers for I2C and SPI moving us
closer to converting to regmap completely and avoiding some
randconfig hassle.
- Provide both manually and transparently locked DAPM APIs rather than
a mix of the two fixing some concurrency issues.
- Start converting CODEC drivers to use separate bus interface drivers
rather than having them all in one file helping avoid dependency
issues.
- DPCM support for Intel Haswell and Bay Trail platforms.
- Lots of work on improvements for simple-card, DaVinci and the Renesas
rcar drivers.
- New drivers for Analog Devices ADAU1977, TI PCM512x and parts of the
CSR SiRF SoC.
This commit adds a bare bones driver support for TLV320AIC31XX family
audio codecs. The driver adds basic stereo playback trough headphone
and speaker outputs and mono capture trough microphone inputs.
The driver is currently missing support at least for mini DSP features
and jack detection. I have tested the driver only on TLV320AIC3111,
but based on the data sheets TLV320AIC3100, TLV320AIC3110, and
TLV320AIC3120 should work Ok too.
The base for the implementation was taken from:
git@gitorious.org:ti-codecs/ti-codecs.git ajitk/topics/k3.10.1-aic31xx
-branch at commit 77504eba0294764e9e63b4a0c696b44db187cd13.
Signed-off-by: Jyri Sarha <jsarha@ti.com> Signed-off-by: Mark Brown <broonie@linaro.org>
ASoC: s6105-ipcam: Convert to table based DAPM setup
Use table based setup to register the DAPM widgets and routes. This on one hand
makes the code a bit shorter and cleaner and on the other hand the board level
DAPM elements get registered in the card's DAPM context rather than in the
CODEC's DAPM context.
While we are at it also remove the snd_soc_dapm_enable_pin() in the init
callback, since pins are enabled by default. Also drop the snd_soc_dapm_sync()
calls, since they are ignored by the core anyway until the card has been fully
instantiated.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Mark Brown <broonie@linaro.org>
Stephen Warren [Mon, 10 Mar 2014 16:38:40 +0000 (10:38 -0600)]
ASoC: Intel: don't select RT5640 if !I2C
The rt5640 driver won't compile without I2C enabled. Hence, the Intel
Haswell and Baytrail+RT5640 ASoC drivers must also depend on I2C, since
these select RT5640.
This solves:
sound/soc/codecs/rt5640.c:2220:1: warning: data definition has no type or storage class [enabled by default]
sound/soc/codecs/rt5640.c:2220:1: error: type defaults to ‘int’ in declaration of ‘module_i2c_driver’ [-Werror=implicit-int]
sound/soc/codecs/rt5640.c:2220:1: warning: parameter names (without types) in function declaration [enabled by default]
sound/soc/codecs/rt5640.c:2210:26: warning: ‘rt5640_i2c_driver’ defined but not used [-Wunused-variable]
Reported-by: Jim Davis <jim.epost@gmail.com> Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Mark Brown <broonie@linaro.org>
ASoC: pxa: tosa: Convert to table based DAPM and control setup
Use table based setup to register the controls and DAPM widgets and routes. This
on one hand makes the code a bit shorter and cleaner and on the other hand the
board level DAPM elements get registered in the card's DAPM context rather than
in the CODEC's DAPM context.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Mark Brown <broonie@linaro.org>
ASoC: pxa: magician: Convert to table based DAPM and control setup
Use table based setup to register the controls and DAPM widgets and routes. This
on one hand makes the code a bit shorter and cleaner and on the other hand the
board level DAPM elements get registered in the card's DAPM context rather than
in the CODEC's DAPM context.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Mark Brown <broonie@linaro.org>
ASoC: snappercl15: Convert to table based DAPM setup
Use table based setup to register the DAPM widgets and routes. This on one hand
makes the code a bit shorter and cleaner and on the other hand the board level
DAPM elements get registered in the card's DAPM context rather than in the
CODEC's DAPM context.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Mark Brown <broonie@linaro.org>
snd_soc_dapm_mutex_unlock() wants a pointer to the DAPM context, not the CODEC.
Fixes: 03510ca07 ("ASoC: ams-delta: Update locking around use of DAPM pin API") Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Mark Brown <broonie@linaro.org>
Takashi Iwai [Thu, 13 Mar 2014 08:53:25 +0000 (09:53 +0100)]
Merge tag 'asoc-v3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Updates for v3.15
Quite a busy release for ASoC this time, more on janitorial work than
exciting new features but welcome nontheless:
- Lots of cleanups from Takashi for enumerations; the original API for
these was error prone so he's refactored lots of code to use more
modern APIs which avoid issues.
- Elimination of the ASoC level wrappers for I2C and SPI moving us
closer to converting to regmap completely and avoiding some
randconfig hassle.
- Provide both manually and transparently locked DAPM APIs rather than
a mix of the two fixing some concurrency issues.
- Start converting CODEC drivers to use separate bus interface drivers
rather than having them all in one file helping avoid dependency
issues.
- DPCM support for Intel Haswell and Bay Trail platforms.
- Lots of work on improvements for simple-card, DaVinci and the Renesas
rcar drivers.
- New drivers for Analog Devices ADAU1977, TI PCM512x and parts of the
CSR SiRF SoC.
Mark Brown [Wed, 12 Mar 2014 23:03:56 +0000 (23:03 +0000)]
Merge tag 'asoc-v3.14-rc6' into asoc-linus
ASoC: Fixes for v3.14
A few things here:
- Avoid memory leaks in error cases with DPCM, this code has never been
that well tested in mainline due to the lack of mainline drivers but
we now have one queued for the merge window!
- Fix the N810 audio driver to load when booted with DT since the
platform was converted to DT during the merge window.
- Fixes for initialisation of some MFD drivers that are probably unused
in mainline
# gpg: Signature made Mon 10 Mar 2014 18:21:32 GMT using RSA key ID 7EA229BD
# gpg: Good signature from "Mark Brown <broonie@sirena.org.uk>"
# gpg: aka "Mark Brown <broonie@debian.org>"
# gpg: aka "Mark Brown <broonie@kernel.org>"
# gpg: aka "Mark Brown <broonie@tardis.ed.ac.uk>"
# gpg: aka "Mark Brown <broonie@linaro.org>"
# gpg: aka "Mark Brown <Mark.Brown@linaro.org>"
Mark Brown [Wed, 12 Mar 2014 13:32:34 +0000 (13:32 +0000)]
ASoC: tlv320aic23: Remove spurious bits per word setting
regmap should handle any byte ordering issues required, it is looking for
a byte stream from the bus, so don't set 16 bits per word. This is likely
to have tested out OK due to use of an unmerged SPI controller driver.
Signed-off-by: Mark Brown <broonie@linaro.org> Tested-by: Max Filippov <jcmvbkbc@gmail.com>
Freeing the current list element while iterating over the list will cause a use
after free since the iterator function will still use the current element to
look up the next. Use list_for_each_safe() and remove the element from the list
before freeing it to avoid this.
Fixes: 1438c2f60b ("ASoC: Add a per component dai list") Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Mark Brown <broonie@linaro.org>
Jean Delvare [Tue, 11 Mar 2014 10:38:34 +0000 (11:38 +0100)]
ALSA: cs5535audio: Also needed on MIPS
The CS5536 companion chipset is not only used on 32-bit x86 systems as
I originally thought, it is also used on MIPS Loongson/Lemote 2
systems. So let the snd-cs5535audio driver be built on MIPS too.
Signed-off-by: Jean Delvare <jdelvare@suse.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Xiubo Li [Tue, 11 Mar 2014 04:43:21 +0000 (12:43 +0800)]
ASoC: io: New signature for snd_soc_codec_set_cache_io()
Now that all users have been converted to regmap and the config.reg_bits
and config.val_bits can be setted by each user through regmap core API.
So these two params are redundant here.
Since the only control type that left is SND_SOC_REGMAP, so remove it. Drop
the control params and add struct regmap *regmap to simplify the code.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com> Signed-off-by: Mark Brown <broonie@linaro.org>
Mark Brown [Tue, 11 Mar 2014 09:58:55 +0000 (09:58 +0000)]
Merge branches 'topic/ad193x', 'topic/tlv320aic23', 'topic/tlv320aic32x4', 'topic/wm8991', 'fix/si476x' and 'fix/88pm860' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into asoc-io
sh-specific "CCR" and "CCR2" have been prefixed by "SH_" in commit a5f6ea29f9a918403629f8369ae55fac6b09cb53 ('sh: prefix sh-specific "CCR" and
"CCR2" by "SH_"').
Jean Delvare [Mon, 10 Mar 2014 20:12:26 +0000 (21:12 +0100)]
ALSA: cs553*: Fix dependencies
The CS5530, CS5535 and CS5536 chipsets are companions of the Geode
series of processors, which are 32-bit x86 processors. So the
snd-cs5530 and snd-cs5535audio drivers are only needed on this
architecture, except for build testing purpose.
Signed-off-by: Jean Delvare <jdelvare@suse.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Takashi Iwai [Tue, 11 Mar 2014 06:50:33 +0000 (07:50 +0100)]
Merge tag 'asoc-v3.14-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v3.14
A few things here:
- Avoid memory leaks in error cases with DPCM, this code has never been
that well tested in mainline due to the lack of mainline drivers but
we now have one queued for the merge window!
- Fix the N810 audio driver to load when booted with DT since the
platform was converted to DT during the merge window.
- Fixes for initialisation of some MFD drivers that are probably unused
in mainline
Use table based setup to register the DAPM widgets and routes. This on one hand
makes the code a bit shorter and cleaner and on the other hand the board level
DAPM elements get registered in the card's DAPM context rather than in the
CODEC's DAPM context.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Mark Brown <broonie@linaro.org>
Mark Brown [Thu, 6 Mar 2014 08:49:11 +0000 (16:49 +0800)]
ASoC: dapm: Sprinkle lockdep asserts through the code
Try to spot locking issues by asserting that the DAPM mutex is held when
it should be. There's a bit of fun due to us not requiring the lock to be
held prior to the card being instantiated which mean we need to wrap the
assert in some paths and this isn't methodical by any stretch of the
imagination.
Now that every DAI has a component we can track the DAIs on a per component
basis. This simplifies the DAI lookup when we are only interested in DAIs of a
specific component and also makes it possible to have multiple components with
the same parent device and also register DAIs.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Mark Brown <broonie@linaro.org>
snd_soc_register_dais() looks up the CODEC that is registering the DAIs by
looping over all registered CODECs. This patch updates the code to
simply pass the CODEC that registers the DAIs to snd_soc_register_dais() thus
avoiding the lookup.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Mark Brown <broonie@linaro.org>
ASoC: Consolidate snd_soc_register_dai() and snd_soc_register_dais()
snd_soc_register_dais() has basically the same code as snd_soc_register_dai(),
but running in a loop. The only difference is that snd_soc_register_dai() calls
fmt_single_name() to generate the DAIs name and snd_soc_register_dais() calls
fmt_multiple_name(). This patch pushes the check in __snd_soc_register_component()
which decides whether to call snd_soc_register_dai() or snd_soc_register_dais()
to snd_soc_register_dais() to decide which naming scheme to use. This allows us
to remove snd_soc_register_dai().
The patch also updates snd_soc_register_dais() to unregister every DAI it finds
for the component rather than trying to unregister one DAI for each DAI that was
registered. Both have the same result since there won't be more DAIs than what
have been registered, but the former is easier to implement.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Mark Brown <broonie@linaro.org>
The 88pm860 is a MFD device and the CODEC driver is using the regmap struct of
the parent device, hence automatic IO setup will not work and we need to
manually call snd_soc_codec_set_cache_io(). The issue was introduced in commit f9ded3b2e7 ("ASoC: 88pm860x: Use regmap for I/O").
Fixes: f9ded3b2e7 ("ASoC: 88pm860x: Use regmap for I/O"). Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Mark Brown <broonie@linaro.org> Cc: stable@vger.kernel.org
The si476x is a MFD device and the CODEC driver is using the regmap struct of
the parent device, hence automatic IO setup will not work and we need to
manually call snd_soc_codec_set_cache_io(). The issue was introduced commit d6173df35f ("ASoC: si476x: Remove custom register I/O implementation")
Fixes: d6173df35f ("ASoC: si476x: Remove custom register I/O implementation") Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Mark Brown <broonie@linaro.org> Cc: stable@vger.kernel.org
ASoC: sam9g20_wm8731: Convert to table based DAPM setup
Use table based setup to register the DAPM widgets and routes. This on one hand
makes the code a bit shorter and cleaner and on the other hand the board level
DAPM elements get registered in the card's DAPM context rather than in the
CODEC's DAPM context.
While we are at it also remove the snd_soc_dapm_enable_pin() in the init
callback. Pins are enabled by default.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Tested-by: Bo Shen <voice.shen@atmel.com> Acked-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Mark Brown <broonie@linaro.org>
Linus Torvalds [Mon, 10 Mar 2014 02:27:31 +0000 (19:27 -0700)]
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from from Olof Johansson:
"A collection of fixes for ARM platforms. A little large due to us
missing to do one last week, but there's nothing in particular here
that is in itself large and scary.
Mostly a handful of smaller fixes all over the place. The majority is
made up of fixes for OMAP, but there are a few for others as well. In
particular, there was a decision to rename a binding for the Broadcom
pinctrl block that we need to go in before the final release since we
then treat it as ABI"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: dts: omap3-gta04: Add ti,omap36xx to compatible property to avoid problems with booting
ARM: tegra: add LED options back into tegra_defconfig
ARM: dts: omap3-igep: fix boot fail due wrong compatible match
ARM: OMAP3: Fix pinctrl interrupts for core2
pinctrl: Rename Broadcom Capri pinctrl binding
pinctrl: refer to updated dt binding string.
Update dtsi with new pinctrl compatible string
ARM: OMAP: Kill warning in CPUIDLE code with !CONFIG_SMP
ARM: OMAP2+: Add support for thumb mode on DT booted N900
ARM: OMAP2+: clock: fix clkoutx2 with CLK_SET_RATE_PARENT
ARM: OMAP4: hwmod: Fix SOFTRESET logic for OMAP4
ARM: DRA7: hwmod data: correct the sysc data for spinlock
ARM: OMAP5: PRM: Fix reboot handling
ARM: sunxi: dt: Change the touchscreen compatibles
ARM: sun7i: dt: Fix interrupt trigger types
Linus Torvalds [Mon, 10 Mar 2014 02:17:39 +0000 (19:17 -0700)]
Merge tag 'nfs-for-3.14-5' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client bugfixes from Trond Myklebust:
"Highlights include:
- Fix another nfs4_sequence corruptor in RELEASE_LOCKOWNER
- Fix an Oopsable delegation callback race
- Fix another bad stateid infinite loop
- Fail the data server I/O is the stateid represents a lost lock
- Fix an Oopsable sunrpc trace event"
* tag 'nfs-for-3.14-5' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
SUNRPC: Fix oops when trace sunrpc_task events in nfs client
NFSv4: Fail the truncate() if the lock/open stateid is invalid
NFSv4.1 Fail data server I/O if stateid represents a lost lock
NFSv4: Fix the return value of nfs4_select_rw_stateid
NFSv4: nfs4_stateid_is_current should return 'true' for an invalid stateid
NFS: Fix a delegation callback race
NFSv4: Fix another nfs4_sequence corruptor
Linus Torvalds [Mon, 10 Mar 2014 01:59:14 +0000 (18:59 -0700)]
Merge tag 'usb-3.14-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are 4 USB fixes for your current tree.
Two of them are reverts to hopefully resolve the nasty XHCI
regressions we have been having on some types of devices. The other
two are quirks for some Logitech video devices"
* tag 'usb-3.14-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
Revert "USBNET: ax88179_178a: enable tso if usb host supports sg dma"
Revert "xhci 1.0: Limit arbitrarily-aligned scatter gather."
usb: Make DELAY_INIT quirk wait 100ms between Get Configuration requests
usb: Add device quirk for Logitech HD Pro Webcams C920 and C930e
Linus Torvalds [Mon, 10 Mar 2014 01:58:27 +0000 (18:58 -0700)]
Merge tag 'staging-3.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver tree fix from Greg KH:
"Here is a single staging driver fix for your tree.
It resolves an issue with arbritary writes to memory if a specific
driver is loaded"
* tag 'staging-3.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging/cxt1e1/linux.c: Correct arbitrary memory write in c4_ioctl()
David Howells [Sun, 9 Mar 2014 08:21:58 +0000 (08:21 +0000)]
KEYS: Make the keyring cycle detector ignore other keyrings of the same name
This fixes CVE-2014-0102.
The following command sequence produces an oops:
keyctl new_session
i=`keyctl newring _ses @s`
keyctl link @s $i
The problem is that search_nested_keyrings() sees two keyrings that have
matching type and description, so keyring_compare_object() returns true.
s_n_k() then passes the key to the iterator function -
keyring_detect_cycle_iterator() - which *should* check to see whether this is
the keyring of interest, not just one with the same name.
Because assoc_array_find() will return one and only one match, I assumed that
the iterator function would only see an exact match or never be called - but
the iterator isn't only called from assoc_array_find()...
Linus Torvalds [Sun, 9 Mar 2014 20:52:53 +0000 (13:52 -0700)]
Merge branch 'for-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux
Pull thermal fixes from Zhang Rui:
"Specifics:
- Update the help text of INT3403 Thermal driver, which was not
friendly to users. From Zhang Rui.
- The "type" sysfs attribute of x86_pkg_temp_thermal registered
thermal zones includes an instance number, which makes the
thermal-to-hwmon bridge fails to group them all in a single hwmon
device. Fixed by Jean Delvare.
- The hwmon device registered by x86_pkg_temp_thermal driver is
redundant because the temperature value reported by
x86_pkg_temp_thermal is already reported by the coretemp driver.
Fixed by Jean Delvare.
- Fix a problem that the cooling device can not be updated properly
if it is initialized at max cooling state. From Ni Wade.
- Fix a problem that OF registered thermal zones are running without
thermal governors. From Zhang Rui.
- Commit beeb5a1e0ef7 ("thermal: rcar-thermal: Enable driver
compilation with COMPILE_TEST") broke build on archs wihout io
memory. Thus make it depend on HAS_IOMEM to bypass build failures.
Fixed by Richard Weinberger"
* 'for-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
Thermal: thermal zone governor fix
Thermal: Allow first update of cooling device state
thermal,rcar_thermal: Add dependency on HAS_IOMEM
x86_pkg_temp_thermal: Fix the thermal zone type
x86_pkg_temp_thermal: Do not expose as a hwmon device
Thermal: update INT3404 thermal driver help text
Linus Torvalds [Sun, 9 Mar 2014 20:51:47 +0000 (13:51 -0700)]
Merge tag 'spi-v3.14-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A scattering of driver specific fixes here.
The fixes from Axel cover bitrot in apparently unmaintained drivers,
the at79 bug is fixing a glitch on /CS during initialisation of some
devices which could break some slaves and the remainder are fixes for
recently introduced bugs from the past release cycle or so"
* tag 'spi-v3.14-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: atmel: add missing spi_master_{resume,suspend} calls to PM callbacks
spi: coldfire-qspi: Fix getting correct address for *mcfqspi
spi: fsl-dspi: Fix getting correct address for master
spi: spi-ath79: fix initial GPIO CS line setup
spi: spi-imx: spi_imx_remove: do not disable disabled clocks
spi-topcliff-pch: Fix probing when DMA mode is used
spi/topcliff-pch: Fix DMA channel
Pull SCSI target fixes from Nicholas Bellinger:
"This series addresses a number of outstanding issues wrt to active I/O
shutdown using iser-target. This includes:
- Fix a long standing tpg_state bug where a tpg could be referenced
during explicit shutdown (v3.1+ stable)
- Use list_del_init for iscsi_cmd->i_conn_node so list_empty checks
work as expected (v3.10+ stable)
- Fix a isert_conn->state related hung task bug + ensure outstanding
I/O completes during session shutdown. (v3.10+ stable)
- Fix isert_conn->post_send_buf_count accounting for RDMA READ/WRITEs
(v3.10+ stable)
- Ignore FRWR completions during active I/O shutdown (v3.12+ stable)
- Fix command leakage for interrupt coalescing during active I/O
shutdown (v3.13+ stable)
Also included is another DIF emulation fix from Sagi specific to
v3.14-rc code"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
Target/sbc: Fix sbc_copy_prot for offset scatters
iser-target: Fix command leak for tx_desc->comp_llnode_batch
iser-target: Ignore completions for FRWRs in isert_cq_tx_work
iser-target: Fix post_send_buf_count for RDMA READ/WRITE
iscsi/iser-target: Fix isert_conn->state hung shutdown issues
iscsi/iser-target: Use list_del_init for ->i_conn_node
iscsi-target: Fix iscsit_get_tpg_from_np tpg_state bug
Revert "ACPI / sleep: pm_power_off needs more sanity checks to be installed"
Revert commit 3130497f5bab ("ACPI / sleep: pm_power_off needs more
sanity checks to be installed") that breaks power ACPI power off on a
lot of systems, because it checks wrong registers.
Fixes: 3130497f5bab ("ACPI / sleep: pm_power_off needs more sanity checks to be installed") Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Charles Keepax [Fri, 7 Mar 2014 16:34:25 +0000 (16:34 +0000)]
ASoC: arizona: Support new fratio encoding on the wm5110 rev D
The reference clock path on newer IP FLLs requires a different
configuration, and should avoid integer mode operation. This patch adds
support for both the new encoding and updates the calculation.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Signed-off-by: Mark Brown <broonie@linaro.org>
Charles Keepax [Fri, 7 Mar 2014 16:34:23 +0000 (16:34 +0000)]
ASoC: arizona: Calculate FLL gain last
No part of the FLL calculation depends on the value determined for the
gain but the gain does depend on other values. In preparation for future
updates this patch moves the gain to be the last thing calculated.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Signed-off-by: Mark Brown <broonie@linaro.org>
Charles Keepax [Fri, 7 Mar 2014 16:34:21 +0000 (16:34 +0000)]
ASoC: arizona: Don't pass Fout into arizona_calc_fll
As we now calculate the FLL configuration at a later stage in the
process the fout member of the FLL structure will contain the desired
Fout frequency so no need to pass this in seperately.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Signed-off-by: Mark Brown <broonie@linaro.org>
Charles Keepax [Fri, 7 Mar 2014 16:34:20 +0000 (16:34 +0000)]
ASoC: arizona: Move calculation of FLL configuration
Currently the FLL configuration is calculated before it is known which
FLL path the configuration will be applied to. Newer versions of the IP
have differences in the configuration required for each FLL path, which
makes it complicated to calculate the FLL configuration in advance.
This patch simply checks the validity of a requested input and output
frequency before we know which FLL path they will be applied to and
saves the actual calculation of the configuration until we know where
the settings will be applied.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Signed-off-by: Mark Brown <broonie@linaro.org>
Charles Keepax [Fri, 7 Mar 2014 16:34:19 +0000 (16:34 +0000)]
ASoC: arizona: Move set of OUTDIV in to arizona_apply_fll
Since we know in arizona_apply_fll if we are setting the sync or ref
path there is no need to set the outdiv seperately anymore. This patch
moves this from arizona_enable_fll to arizona_apply_fll.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Signed-off-by: Mark Brown <broonie@linaro.org>