The sg struct is used without being initialized, which breaks
when CONFIG_DEBUG_SG is enabled.
Cc: stable@vger.kernel.org Signed-off-by: Richard W.M. Jones <rjones@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Robert Love [Mon, 24 Sep 2012 18:52:56 +0000 (11:52 -0700)]
[SCSI] Documentation: Add lesb/ to path for LESB attributes in FCoE bus documentation
The Link Error Status Block attributes are incorrectly named as they do
not have the lesb_ prefix, but instead are grouped in the lesb/ attribute
group.
Signed-off-by: Robert Love <robert.w.love@intel.com> Tested-by: Ross Brattain <ross.b.brattain@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Yi Zou [Mon, 24 Sep 2012 18:52:50 +0000 (11:52 -0700)]
[SCSI] libfc: fix lun reset failure bugs in fc_fcp_resp handling of FCP_RSP_INFO
In LUN RESET testing involving NetApp targets, it is observed that LUN
RESET is failing. The fc_fcp_resp() is not completing the completion
for the LUN RESET task since fc_fcp_resp assumes that the FCP_RSP_INFO
is 8 bytes with the 4 byte reserved field, where in case of NetApp targets
the FCP_RSP to LUN RESET only has 4 bytes of FCP_RSP_INFO. This leads
fc_fcp_resp to error out w/o completing the task completion, eventually
causing LUN RESET to be escalated to host reset, which is not very nice.
Per FCP-3 r04, clause 9.5.15 and Table 23, the FCP_RSP_INFO field can be either
4 bytes or 8 bytes, with the last 4 bytes as "Reserved (if any)". Therefore it
is valid to have 4 bytes FCP_RSP_INFO like some of the NetApp targets behave.
Fixing this by validating the FCP_RSP_INFO against both the two spec allowed
length.
Reported-by: Frank Zhang <frank_1.zhang@intel.com> Signed-off-by: Yi Zou <yi.zou@intel.com> Tested-by: Ross Brattain <ross.b.brattain@intel.com> Signed-off-by: Robert Love <robert.w.love@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
SCSI errors were generated while writing to LUNs
connected via NPIV ports.
Debugging this it was found that the FCoE packets
transmitted via the NPIV ports were not tagged with
correct user priority as negotiated with peer by DCB
agent. This resulted in FCoE traffic going with priority
zero(0) that did not have priority flow control (PFC)
enabled for it. The initiator after transferring data
to the target never saw any reply indicating the transfer
was complete. This resulted in error recovery (ABTS) and
SCSI command retries by the scsi-mid layer; eventually
resulting in I/O errors.
This patch fixes this issue by keeping the FCoE user
priority information in the fcoe_interface instance
that is common for both the physical port as well as
NPIV ports connected to that physical port; instead
of storing it in fcoe_port structure that has a per
port instance.
Signed-off-by: Neerav Parikh <Neerav.Parikh@intel.com> Acked-by: Yi Zou <yi.zou@intel.com> Acked-by: John Fastabend <john.r.fastabend@intel.com> Tested-by: Marcus Dennis <marcusx.e.dennis@intel.com> Signed-off-by: Robert Love <robert.w.love@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Modified the firmware naming convention to contain the
firmware image version (3.1.0.0).
- The new convention is <firmware-image>-<firmware-version>.bin
- The change will enforce loading only compatible firmware with this driver
and also avoid over-writing the old firmware image in-order to load new
version driver as the firmware names used to be the same.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
[SCSI] bfa: Add support to configure min/max bandwidth for a pcifn
- Added support to configure minimum bandwidth for a pcifn.
- Minimum bandwith is guaranteed at per queue level.
- Added support to update pcifn bandwidth dynamically without
a server reboot.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Made changes such that once the PWWN is acquired from the fabric through FAA,
and if the FAPWWN configuration is modified on the switch side, driver should
show relevant information to the user.
- Added logic to cache the reason code when the given port is disabled implicitl
due to FAA error condition.
- If the port is disabled, while sending SCN to upper layer, update the
reason code appropriately. With this, BFA FC port state machine will enter
into faa_err_config state. This state will be shown to the user.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Introduced support for D-Port which is a new port mode during which
link level diagnostics can be run.
- Provided mechanism to dynamically configure D-Port and initiate diagnostic
tests to isolate any link level issues.
- In D-Port mode, the HBA port does not participate in fabric or login to the
remote device or run data traffic.
- Diagnostic tests include running various loopback tests in conjunction with
the attached device.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
[SCSI] bfa: Fix to handle firmware tskim abort request response
- Enhance tracing to include both tskim tag and event.
- Handle the tskim abort response from firmware in the
tskim state machine cleanup state and proceed with the
tskim cleanup.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
[SCSI] bfa: Fix few attributes in the RHBA CT passthru command
- Made changes to set the RHBA command max payload based on
the port configured frame size.
- Made changes to fix the driver/fw version size in FMDI structure.
- Fix to pass the fw version for FDMI attribute type
FDMI_HBA_ATTRIB_FW_VERSION rather than driver version.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Made changes to check the flash controller status before IOC initialization.
- Made changes to poll on the FLASH_STS_REG bit to check if the flash controller
initialization is completed during the PLL init.
- Add support to handle STOP/DISABLE events in the IOCFC state machine.
- Made changes to bring the IOC down on a flash driver config read failure.
- Added logic to clean the use count and fail sync registers during IOCFC init.
[SCSI] bfa: Add support for FC Arbitrated Loop topology.
- Add private loop topology support at 2G/4G/8G speeds with following
limitations
1. No support for multiple initiators in the loop
2. No public loop support. If attached to a loop with an FL_Port,
device continues to work as a private NL_Port in the loop
3. No auto topology detection. User has to manually set the
configured topology to loop if attaching to loop.
- When loop topology is configured, enabling FC port features
QoS/Trunk/TRL are not allowed and vice versa.
Linus Torvalds [Wed, 3 Oct 2012 05:09:10 +0000 (22:09 -0700)]
Merge tag 'stable/for-linus-3.7-x86-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull Xen update from Konrad Rzeszutek Wilk:
"Features:
- When hotplugging PCI devices in a PV guest we can allocate
Xen-SWIOTLB later.
- Cleanup Xen SWIOTLB.
- Support pages out grants from HVM domains in the backends.
- Support wild cards in xen-pciback.hide=(BDF) arguments.
- Update grant status updates with upstream hypervisor.
- Boot PV guests with more than 128GB.
- Cleanup Xen MMU code/add comments.
- Obtain XENVERS using a preferred method.
- Lay out generic changes to support Xen ARM.
- Allow privcmd ioctl for HVM (used to do only PV).
- Do v2 of mmap_batch for privcmd ioctls.
- If hypervisor saves the LED keyboard light - we will now instruct
the kernel about its state.
Fixes:
- More fixes to Xen PCI backend for various calls/FLR/etc.
- With more than 4GB in a 64-bit PV guest disable native SWIOTLB.
- Fix up smatch warnings.
- Fix up various return values in privmcmd and mm."
* tag 'stable/for-linus-3.7-x86-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen: (48 commits)
xen/pciback: Restore the PCI config space after an FLR.
xen-pciback: properly clean up after calling pcistub_device_find()
xen/vga: add the xen EFI video mode support
xen/x86: retrieve keyboard shift status flags from hypervisor.
xen/gndev: Xen backend support for paged out grant targets V4.
xen-pciback: support wild cards in slot specifications
xen/swiotlb: Fix compile warnings when using plain integer instead of NULL pointer.
xen/swiotlb: Remove functions not needed anymore.
xen/pcifront: Use Xen-SWIOTLB when initting if required.
xen/swiotlb: For early initialization, return zero on success.
xen/swiotlb: Use the swiotlb_late_init_with_tbl to init Xen-SWIOTLB late when PV PCI is used.
xen/swiotlb: Move the error strings to its own function.
xen/swiotlb: Move the nr_tbl determination in its own function.
xen/arm: compile and run xenbus
xen: resynchronise grant table status codes with upstream
xen/privcmd: return -EFAULT on error
xen/privcmd: Fix mmap batch ioctl error status copy back.
xen/privcmd: add PRIVCMD_MMAPBATCH_V2 ioctl
xen/mm: return more precise error from xen_remap_domain_range()
xen/mmu: If the revector fails, don't attempt to revector anything else.
...
Linus Torvalds [Wed, 3 Oct 2012 05:08:14 +0000 (22:08 -0700)]
Merge tag 'stable/for-linus-3.7-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/mm
Pull frontswap update from Konrad Rzeszutek Wilk:
"Features:
- Support exlusive get if backend is capable.
Bug-fixes:
- Fix compile warnings
- Add comments/cleanup doc
- Fix wrong if condition"
* tag 'stable/for-linus-3.7-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/mm:
frontswap: support exclusive gets if tmem backend is capable
mm: frontswap: fix a wrong if condition in frontswap_shrink
mm/frontswap: fix uninit'ed variable warning
mm/frontswap: cleanup doc and comment error
mm: frontswap: remove unneeded headers
Linus Torvalds [Wed, 3 Oct 2012 04:38:48 +0000 (21:38 -0700)]
Merge branch 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security
Pull security subsystem updates from James Morris:
"Highlights:
- Integrity: add local fs integrity verification to detect offline
attacks
- Integrity: add digital signature verification
- Simple stacking of Yama with other LSMs (per LSS discussions)
- IBM vTPM support on ppc64
- Add new driver for Infineon I2C TIS TPM
- Smack: add rule revocation for subject labels"
Fixed conflicts with the user namespace support in kernel/auditsc.c and
security/integrity/ima/ima_policy.c.
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security: (39 commits)
Documentation: Update git repository URL for Smack userland tools
ima: change flags container data type
Smack: setprocattr memory leak fix
Smack: implement revoking all rules for a subject label
Smack: remove task_wait() hook.
ima: audit log hashes
ima: generic IMA action flag handling
ima: rename ima_must_appraise_or_measure
audit: export audit_log_task_info
tpm: fix tpm_acpi sparse warning on different address spaces
samples/seccomp: fix 31 bit build on s390
ima: digital signature verification support
ima: add support for different security.ima data types
ima: add ima_inode_setxattr/removexattr function and calls
ima: add inode_post_setattr call
ima: replace iint spinblock with rwlock/read_lock
ima: allocating iint improvements
ima: add appraise action keywords and default rules
ima: integrity appraisal extension
vfs: move ima_file_free before releasing the file
...
Linus Torvalds [Wed, 3 Oct 2012 03:49:15 +0000 (20:49 -0700)]
Merge tag 'upstream-3.7-rc1' of git://git.infradead.org/linux-ubi
Pull UBI changes from Artem Bityutskiy:
"The main change is the way we reserve eraseblocks for bad blocks
handling. We used to reserve 2% of the partition, but now we are more
aggressive and we reserve 2% of the entire chip, which is what
actually manufacturers specify in data sheets. We introduced an
option to users to override the default, though.
There are a couple of fixes as well, and a number of cleanups."
* tag 'upstream-3.7-rc1' of git://git.infradead.org/linux-ubi: (24 commits)
UBI: fix trivial typo 'it' => 'is'
UBI: load after mtd device drivers
UBI: print less
UBI: use pr_ helper instead of printk
UBI: comply with coding style
UBI: erase free PEB with bitflip in EC header
UBI: fix autoresize handling in R/O mode
UBI: add max_beb_per1024 to attach ioctl
UBI: allow specifying bad PEBs limit using module parameter
UBI: check max_beb_per1024 value in ubi_attach_mtd_dev
UBI: prepare for max_beb_per1024 module parameter addition
UBI: introduce MTD_PARAM_MAX_COUNT
UBI: separate bad_peb_limit in a function
arm: sam9_l9260_defconfig: correct CONFIG_MTD_UBI_BEB_LIMIT
UBI: use the whole MTD device size to get bad_peb_limit
mtd: mtdparts: introduce mtd_get_device_size
mtd: mark mtd_is_partition argument as constant
arm: sam9_l9260_defconfig: remove non-existing config option
UBI: kill CONFIG_MTD_UBI_BEB_RESERVE
UBI: limit amount of reserved eraseblocks for bad PEB handling
...
Linus Torvalds [Wed, 3 Oct 2012 03:47:48 +0000 (20:47 -0700)]
Merge tag 'upstream-3.7-rc1' of git://git.infradead.org/linux-ubifs
Pull ubifs changes from Artem Bityutskiy:
"No big changes for 3.7 in UBIFS:
- Error reporting and debug printing improvements
- Power cut emulation fixes
- Minor cleanups"
Fix trivial conflict in fs/ubifs/debug.c due to the user namespace
changes.
* tag 'upstream-3.7-rc1' of git://git.infradead.org/linux-ubifs:
UBIFS: print less
UBIFS: use pr_ helper instead of printk
UBIFS: comply with coding style
UBIFS: use __aligned() attribute
UBIFS: remove __DATE__ and __TIME__
UBIFS: fix power cut emulation for mtdram
UBIFS: improve scanning debug output
UBIFS: always print full error reports
UBIFS: print PID in debug messages
Linus Torvalds [Wed, 3 Oct 2012 03:42:58 +0000 (20:42 -0700)]
Merge tag 'for-linus-v3.7-rc1' of git://oss.sgi.com/xfs/xfs
Pull xfs update from Ben Myers:
"Several enhancements and cleanups:
- make inode32 and inode64 remountable options
- SEEK_HOLE/SEEK_DATA enhancements
- cleanup struct declarations in xfs_mount.h"
* tag 'for-linus-v3.7-rc1' of git://oss.sgi.com/xfs/xfs:
xfs: Make inode32 a remountable option
xfs: add inode64->inode32 transition into xfs_set_inode32()
xfs: Fix mp->m_maxagi update during inode64 remount
xfs: reduce code duplication handling inode32/64 options
xfs: make inode64 as the default allocation mode
xfs: Fix m_agirotor reset during AG selection
Make inode64 a remountable option
xfs: stop the sync worker before xfs_unmountfs
xfs: xfs_seek_hole() refinement with hole searching from page cache for unwritten extents
xfs: xfs_seek_data() refinement with unwritten extents check up from page cache
xfs: Introduce a helper routine to probe data or hole offset from page cache
xfs: Remove type argument from xfs_seek_data()/xfs_seek_hole()
xfs: fix race while discarding buffers [V4]
xfs: check for possible overflow in xfs_ioc_trim
xfs: unlock the AGI buffer when looping in xfs_dialloc
xfs: kill struct declarations in xfs_mount.h
xfs: fix uninitialised variable in xfs_rtbuf_get()
Linus Torvalds [Wed, 3 Oct 2012 03:25:04 +0000 (20:25 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs update from Al Viro:
- big one - consolidation of descriptor-related logics; almost all of
that is moved to fs/file.c
(BTW, I'm seriously tempted to rename the result to fd.c. As it is,
we have a situation when file_table.c is about handling of struct
file and file.c is about handling of descriptor tables; the reasons
are historical - file_table.c used to be about a static array of
struct file we used to have way back).
A lot of stray ends got cleaned up and converted to saner primitives,
disgusting mess in android/binder.c is still disgusting, but at least
doesn't poke so much in descriptor table guts anymore. A bunch of
relatively minor races got fixed in process, plus an ext4 struct file
leak.
- related thing - fget_light() partially unuglified; see fdget() in
there (and yes, it generates the code as good as we used to have).
- also related - bits of Cyrill's procfs stuff that got entangled into
that work; _not_ all of it, just the initial move to fs/proc/fd.c and
switch of fdinfo to seq_file.
- Alex's fs/coredump.c spiltoff - the same story, had been easier to
take that commit than mess with conflicts. The rest is a separate
pile, this was just a mechanical code movement.
- a few misc patches all over the place. Not all for this cycle,
there'll be more (and quite a few currently sit in akpm's tree)."
Fix up trivial conflicts in the android binder driver, and some fairly
simple conflicts due to two different changes to the sock_alloc_file()
interface ("take descriptor handling from sock_alloc_file() to callers"
vs "net: Providing protocol type via system.sockprotoname xattr of
/proc/PID/fd entries" adding a dentry name to the socket)
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (72 commits)
MAX_LFS_FILESIZE should be a loff_t
compat: fs: Generic compat_sys_sendfile implementation
fs: push rcu_barrier() from deactivate_locked_super() to filesystems
btrfs: reada_extent doesn't need kref for refcount
coredump: move core dump functionality into its own file
coredump: prevent double-free on an error path in core dumper
usb/gadget: fix misannotations
fcntl: fix misannotations
ceph: don't abuse d_delete() on failure exits
hypfs: ->d_parent is never NULL or negative
vfs: delete surplus inode NULL check
switch simple cases of fget_light to fdget
new helpers: fdget()/fdput()
switch o2hb_region_dev_write() to fget_light()
proc_map_files_readdir(): don't bother with grabbing files
make get_file() return its argument
vhost_set_vring(): turn pollstart/pollstop into bool
switch prctl_set_mm_exe_file() to fget_light()
switch xfs_find_handle() to fget_light()
switch xfs_swapext() to fget_light()
...
Linus Torvalds [Wed, 3 Oct 2012 02:13:12 +0000 (19:13 -0700)]
Merge branch 'for-v3.7' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping
Pull CMA and DMA-mapping updates from Marek Szyprowski:
"This time the pull request is rather small, because the further
redesign patches were not ready on time.
This pull request consists of the patches which extend ARM DMA-mapping
subsystem with support for CPU coherent (ACP) DMA busses. The first
client of the new version is HighBank SATA driver. The second part of
the pull request includes various cleanup for both CMA common code and
ARM DMA-mapping subsystem."
Fix up trivial add-add conflict due to the "dma-coherent" DT property
being added next to the "calxeda,port-phys" property for the Calxeda
AHCI controller.
* 'for-v3.7' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping:
ARM: dma-mapping: Remove unsed var at arm_coherent_iommu_unmap_page
ARM: highbank: add coherent DMA setup
ARM: kill off arch_is_coherent
ARM: add coherent iommu dma ops
ARM: add coherent dma ops
ARM: dma-mapping: Refrain noisy console message
ARM: dma-mapping: Small logical clean up
drivers: dma-contiguous: refactor dma_alloc_from_contiguous()
Linus Torvalds [Wed, 3 Oct 2012 02:01:32 +0000 (19:01 -0700)]
Merge tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull first round of SCSI updates from James Bottomley:
"This is a large set of updates, mostly for drivers (qla2xxx [including
support for new 83xx based card], qla4xxx, mpt2sas, bfa, zfcp, hpsa,
be2iscsi, isci, lpfc, ipr, ibmvfc, ibmvscsi, megaraid_sas).
There's also a rework for tape adding virtually unlimited numbers of
tape drives plus a set of dif fixes for sd and a fix for a live lock
on hot remove of SCSI devices.
This round includes a signed tag pull of isci-for-3.6
Signed-off-by: James Bottomley <JBottomley@Parallels.com>"
Fix up trivial conflict in drivers/scsi/qla2xxx/qla_nx.c due to new PCI
helper function use in a function that was removed by this pull.
* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (198 commits)
[SCSI] st: remove st_mutex
[SCSI] sd: Ensure we correctly disable devices with unknown protection type
[SCSI] hpsa: gen8plus Smart Array IDs
[SCSI] qla4xxx: Update driver version to 5.03.00-k1
[SCSI] qla4xxx: Disable generating pause frames for ISP83XX
[SCSI] qla4xxx: Fix double clearing of risc_intr for ISP83XX
[SCSI] qla4xxx: IDC implementation for Loopback
[SCSI] qla4xxx: update copyrights in LICENSE.qla4xxx
[SCSI] qla4xxx: Fix panic while rmmod
[SCSI] qla4xxx: Fail probe_adapter if IRQ allocation fails
[SCSI] qla4xxx: Prevent MSI/MSI-X falling back to INTx for ISP82XX
[SCSI] qla4xxx: Update idc reg in case of PCI AER
[SCSI] qla4xxx: Fix double IDC locking in qla4_8xxx_error_recovery
[SCSI] qla4xxx: Clear interrupt while unloading driver for ISP83XX
[SCSI] qla4xxx: Print correct IDC version
[SCSI] qla4xxx: Added new mbox cmd to pass driver version to FW
[SCSI] scsi_dh_alua: Enable STPG for unavailable ports
[SCSI] scsi_remove_target: fix softlockup regression on hot remove
[SCSI] ibmvscsi: Fix host config length field overflow
[SCSI] ibmvscsi: Remove backend abstraction
...
Chuck Lever [Mon, 24 Sep 2012 18:51:48 +0000 (14:51 -0400)]
MAX_LFS_FILESIZE should be a loff_t
fs/nfs/internal.h: In function ‘nfs_super_set_maxbytes’:
fs/nfs/internal.h:547:21: warning: comparison between signed and
unsigned integer expressions [-Wsign-compare]
Seen with gcc (GCC) 4.6.3 20120306 (Red Hat 4.6.3-2).
Commit 42cb56ae made s_maxbytes a loff_t, thus the type of
MAX_LFS_FILESIZE should also be a loff_t.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Acked-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
This function is used by sparc, powerpc and arm64 for compat support.
The patch adds a generic implementation which calls do_sendfile()
directly and avoids set_fs().
The sparc architecture has wrappers for the sign extensions while
powerpc relies on the compiler to do the this. The patch adds wrappers
for powerpc to handle the u32->int type conversion.
compat_sys_sendfile64() can be replaced by a sys_sendfile() call since
compat_loff_t has the same size as off_t on a 64-bit system.
On powerpc, the patch also changes the 64-bit sendfile call from
sys_sendile64 to sys_sendfile.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Acked-by: David S. Miller <davem@davemloft.net> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Paul Mackerras <paulus@samba.org> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
fs: push rcu_barrier() from deactivate_locked_super() to filesystems
There's no reason to call rcu_barrier() on every
deactivate_locked_super(). We only need to make sure that all delayed rcu
free inodes are flushed before we destroy related cache.
Removing rcu_barrier() from deactivate_locked_super() affects some fast
paths. E.g. on my machine exit_group() of a last process in IPC
namespace takes 0.07538s. rcu_barrier() takes 0.05188s of that time.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Al Viro [Wed, 29 Aug 2012 20:31:33 +0000 (16:31 -0400)]
btrfs: reada_extent doesn't need kref for refcount
All increments and decrements are under the same spinlock - have to be,
since they need to protect the radix_tree it's found in. Just use
int, no need to wank with kref...
Linus Torvalds [Wed, 3 Oct 2012 01:32:35 +0000 (18:32 -0700)]
Merge tag 'pm-for-3.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael J Wysocki:
- Improved system suspend/resume and runtime PM handling for the SH
TMU, CMT and MTU2 clock event devices (also used by ARM/shmobile).
- Generic PM domains framework extensions related to cpuidle support
and domain objects lookup using names.
- ARM/shmobile power management updates including improved support for
the SH7372's A4S power domain containing the CPU core.
- cpufreq changes related to AMD CPUs support from Matthew Garrett,
Andre Przywara and Borislav Petkov.
- cpu0 cpufreq driver from Shawn Guo.
- cpufreq governor fixes related to the relaxing of limit from Michal
Pecio.
- OMAP cpufreq updates from Axel Lin and Richard Zhao.
- cpuidle ladder governor fixes related to the disabling of states from
Carsten Emde and me.
- Runtime PM core updates related to the interactions with the system
suspend core from Alan Stern and Kevin Hilman.
- Wakeup sources modification allowing more helper functions to be
called from interrupt context from John Stultz and additional
diagnostic code from Todd Poynor.
- System suspend error code path fix from Feng Hong.
Fixed up conflicts in cpufreq/powernow-k8 that stemmed from the
workqueue fixes conflicting fairly badly with the removal of support for
hardware P-state chips. The changes were independent but somewhat
intertwined.
* tag 'pm-for-3.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (76 commits)
Revert "PM QoS: Use spinlock in the per-device PM QoS constraints code"
PM / Runtime: let rpm_resume() succeed if RPM_ACTIVE, even when disabled, v2
cpuidle: rename function name "__cpuidle_register_driver", v2
cpufreq: OMAP: Check IS_ERR() instead of NULL for omap_device_get_by_hwmod_name
cpuidle: remove some empty lines
PM: Prevent runtime suspend during system resume
PM QoS: Use spinlock in the per-device PM QoS constraints code
PM / Sleep: use resume event when call dpm_resume_early
cpuidle / ACPI : move cpuidle_device field out of the acpi_processor_power structure
ACPI / processor: remove pointless variable initialization
ACPI / processor: remove unused function parameter
cpufreq: OMAP: remove loops_per_jiffy recalculate for smp
sections: fix section conflicts in drivers/cpufreq
cpufreq: conservative: update frequency when limits are relaxed
cpufreq / ondemand: update frequency when limits are relaxed
properly __init-annotate pm_sysrq_init()
cpufreq: Add a generic cpufreq-cpu0 driver
PM / OPP: Initialize OPP table from device tree
ARM: add cpufreq transiton notifier to adjust loops_per_jiffy for smp
cpufreq: Remove support for hardware P-state chips from powernow-k8
...
Linus Torvalds [Wed, 3 Oct 2012 01:23:35 +0000 (18:23 -0700)]
Merge tag 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
Pull libata changes from Jeff Garzik:
"Minor libata updates, nothing notable.
1) Apply -- and then revert -- the FUA feature. Caused disk
corruption in linux-next, proving it cannot be turned on by
default.
Net effect to upstream tree: zero
2) New AHCI platform driver sata_highbank
3) Improve SCSI MODE SENSE handling; support MODE SELECT
4) AHCI: support aggressive device sleep (power mgmt)
5) sata_fsl: minor fix
6) pata_arasan: clk support"
* tag 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
sata_mv: Fix warnings when no PCI
[libata] Makefile: Fix build error in sata_highbank
[libata] export ata_dev_set_feature()
libata-core: use ATA_LBA in ata_build_rw_tf()
ata/ahci_platform: Add clock framework support
pata_arasan: add Device Tree probing capability
pata_arasan: Add clk_{un}prepare() support
ata: add platform driver for Calxeda AHCI controller
sata_fsl: add workaround for data length mismatch on freescale V2 controller
ahci: implement aggressive SATA device sleep support
ata: define enum constants for IDENTIFY DEVICE
Revert "libata: enable SATA disk fua detection on default"
[libata] scsi: implement MODE SELECT command
[libata] scsi: support MODE SENSE request for changeable and default parameters
[libata] scsi: Remove unlikely() from FUA check
libata: enable SATA disk fua detection on default
Linus Torvalds [Wed, 3 Oct 2012 00:26:42 +0000 (17:26 -0700)]
Merge tag 'spi-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/misc
Pull spi updates from Mark Brown:
"No framework work here, only a bunch of driver updates of varying
sizes:
- Factoring out of the core hardware support from the MXS MMC driver
by Marek Vasut to allow the hardware to also be used for SPI.
- Lots of error handling cleanups from Guenter Roeck
- Removal of the existing Tegra driver which is quite comprehensively
broken as detailed in the changelog for the removal.
- DT suppport for the PL022 and GPIO drivers.
- pinctrl support for OMAP and PL022."
Pulling from Mark Brown as Grant Likely is still busy moving.
* tag 'spi-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/misc: (53 commits)
spi: remove completely broken Tegra driver
spi/imx: set the inactive state of the clock according to the clock polarity
spi/pl022: get/put resources on suspend/resume
spi/pl022: use more managed resources
spi/pl022: Devicetree support w/o platform data
spi/s3c64xx: Don't free controller_data on non-dt platforms
spi: omap2-mcspi: add pinctrl support
spi/pl022: adopt pinctrl support
spi: omap2-mcspi: Cleanup the omap2_mcspi_txrx_dma function
spi/gpio: Fix stub for spi_gpio_probe_dt()
spi/mxs: Make the SPI block clock speed configurable via DT
spi: spi-sh-hspi: drop frees of devm_ alloc'd data
spi/pl022: Fix chipselects pointer computation
spi: spi-tle62x0: Use module_spi_driver macro
mxs/spi: Rework the mxs_ssp_timeout to be more readable
mxs/spi: Decrement the DMA/PIO border
mxs/spi: Increment the transfer length only if transfer succeeded
mxs/spi: Fix issues when doing long continuous transfer
spi: spi-gpio: Add DT bindings
spi: spi-gpio: store chipselect information in private structure
...
Linus Torvalds [Wed, 3 Oct 2012 00:20:40 +0000 (17:20 -0700)]
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull infiniband updates from Roland Dreier:
"First batch of InfiniBand/RDMA changes for the 3.7 merge window:
- mlx4 IB support for SR-IOV
- A couple of SRP initiator fixes
- Batch of nes hardware driver fixes
- Fix for long-standing use-after-free crash in IPoIB
- Other miscellaneous fixes"
This merge also removes a new use of __cancel_delayed_work(), and
replaces it with the regular cancel_delayed_work() that is now irq-safe
thanks to the workqueue updates.
That said, I suspect the sequence in question should probably use
"mod_delayed_work()". I just did the minimal "don't use deprecated
functions" fixup, though.
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (45 commits)
IB/qib: Fix local access validation for user MRs
mlx4_core: Disable SENSE_PORT for multifunction devices
mlx4_core: Clean up enabling of SENSE_PORT for older (ConnectX-1/-2) HCAs
mlx4_core: Stash PCI ID driver_data in mlx4_priv structure
IB/srp: Avoid having aborted requests hang
IB/srp: Fix use-after-free in srp_reset_req()
IB/qib: Add a qib driver version
RDMA/nes: Fix compilation error when nes_debug is enabled
RDMA/nes: Print hardware resource type
RDMA/nes: Fix for crash when TX checksum offload is off
RDMA/nes: Cosmetic changes
RDMA/nes: Fix for incorrect MSS when TSO is on
RDMA/nes: Fix incorrect resolving of the loopback MAC address
mlx4_core: Fix crash on uninitialized priv->cmd.slave_sem
mlx4_core: Trivial cleanups to driver log messages
mlx4_core: Trivial readability fix: "0X30" -> "0x30"
IB/mlx4: Create paravirt contexts for VFs when master IB driver initializes
mlx4: Modify proxy/tunnel QP mechanism so that guests do no calculations
mlx4: Paravirtualize Node Guids for slaves
mlx4: Activate SR-IOV mode for IB
...
Linus Torvalds [Wed, 3 Oct 2012 00:16:10 +0000 (17:16 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input updates from Dmitry Torokhov:
"A few drivers were updated with device tree bindings and others got a
few small cleanups and fixes."
Fix trivial conflict in drivers/input/keyboard/omap-keypad.c due to
changes clashing with a whitespace cleanup.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (28 commits)
Input: wacom - mark Intuos5 pad as in-prox when touching buttons
Input: synaptics - adjust threshold for treating position values as negative
Input: hgpk - use %*ph to dump small buffer
Input: gpio_keys_polled - fix dt pdata->nbuttons
Input: Add KD[GS]KBDIACRUC ioctls to the compatible list
Input: omap-keypad - fixed formatting
Input: tegra - move platform data header
Input: wacom - add support for EMR on Cintiq 24HD touch
Input: s3c2410_ts - make s3c_ts_pmops const
Input: samsung-keypad - use of_get_child_count() helper
Input: samsung-keypad - use of_match_ptr()
Input: uinput - fix formatting
Input: uinput - specify exact bit sizes on userspace APIs
Input: uinput - mark failed submission requests as free
Input: uinput - fix race that can block nonblocking read
Input: uinput - return -EINVAL when read buffer size is too small
Input: uinput - take event lock when fetching events from buffer
Input: get rid of MATCH_BIT() macro
Input: rotary-encoder - add DT bindings
Input: rotary-encoder - constify platform data pointers
...
Linus Torvalds [Tue, 2 Oct 2012 23:20:20 +0000 (16:20 -0700)]
Merge tag 'pinctrl-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pinctrl changes from Linus Walleij:
"Some of this stuff is hitting arch/arm/* and have been ACKed by the
ARM SoC folks, or it's device tree bindings pertaining to the specific
driver.
These are the bulk pinctrl changes for kernel v3.7:
- Add subdrivers for the DB8540 and NHK8815 Nomadik-type ASICs,
provide platform config for the Nomadik.
- Add a driver for the i.MX35.
- Add a driver for the BCM2835, an advanced GPIO expander.
- Various fixes and clean-ups and minor improvements for the core,
Nomadik, pinctr-single, sirf drivers.
- Some platform config for the ux500."
* tag 'pinctrl-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (27 commits)
pinctrl: add bcm2835 driver
pinctrl: clarify idle vs sleep states
pinctrl/nomadik: use irq_find_mapping()
pinctrl: sirf: add lost chained_irq_enter and exit in sirfsoc_gpio_handle_irq
pinctrl: sirf: initialize the irq_chip pointer of pinctrl_gpio_range
pinctrl: sirf: fix spinlock deadlock in sirfsoc_gpio_set_input
pinctrl: sirf: add missing pins to pinctrl list
pinctrl: sirf: fix a typo in sirfsoc_gpio_probe
pinctrl: pinctrl-single: add debugfs pin h/w state info
ARM: ux500: 8500: update I2C sleep states pinctrl
pinctrl: Fix potential memory leak in pinctrl_register_one_pin()
ARM: ux500: tidy up pin sleep modes
ARM: ux500: fix spi2 pin group
pinctrl: imx: remove duplicated const
pinctrl: document semantics vs GPIO
ARM: ux500: 8500: use hsit_a_2 group for HSI
pinctrl: use kasprintf() in pinmux_request_gpio()
pinctrl: pinctrl-single: Add pinctrl-single,bits type of mux
pinctrl/nomadik : add MC1_a_2 pin MC1 function group list
pinctrl: pinctrl-single: Make sure we do not change bits outside of mask
...
Linus Torvalds [Tue, 2 Oct 2012 23:05:10 +0000 (16:05 -0700)]
Merge tag 'gpio-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO changes from Linus Walleij:
"So this is the LW GPIO patch stack for v3.7:
- refactoring from Thierry Redding at Arnd Bergmann's request to use
the seq_file iterator interface in gpiolib.
- A new driver for Avionic Design's N-bit GPIO expander.
- Two instances of mutexes replaced by spinlocks from Axel Lin to
code that is supposed to be fastpath compliant.
- IRQ demuxer and gpio_to_irq() support for pcf857x by Kuninori
Morimoto.
- Dynamic GPIO numbers, device tree support, daisy chaining and some
other fixes for the 74x164 driver by Maxime Ripard.
- IRQ domain and device tree support for the tc3589x driver by Lee
Jones.
- Some conversion to use managed resources devm_* code.
- Some instances of clk_prepare() or clk_prepare_enable() added to
support the new, stricter common clock framework.
- Some for_each_set_bit() simplifications.
- Then a lot of fixes as we fixed up all of the above tripping over
our own shoelaces and that kind of thing."
* tag 'gpio-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (34 commits)
gpio: pcf857x: select IRQ_DOMAIN
gpio: Document device_node's det_debounce
gpio-lpc32xx: Add GPI_28
gpio: adnp: dt: Reference generic interrupt binding
gpio: Add Avionic Design N-bit GPIO expander support
gpio: pxa: using for_each_set_bit to simplify the code
gpio_msm: using for_each_set_bit to simplify the code
gpio: Enable the tc3298x GPIO expander driver for Device Tree
gpio: Provide the tc3589x GPIO expander driver with an IRQ domain
ARM: shmobile: kzm9g: use gpio-keys instead of gpio-keys-polled
gpio: pcf857x: fixup smatch WARNING
gpio: 74x164: Add support for the daisy-chaining
gpio: 74x164: dts: Add documentation for the dt binding
dt: Fix incorrect reference in gpio-led documentation
gpio: 74x164: Add device tree support
gpio: 74x164: Use dynamic gpio number assignment if no pdata is present
gpio: 74x164: Use devm_kzalloc
gpio: 74x164: Use module_spi_driver boiler plate function
gpio: sx150x: Use irq_data_get_irq_chip_data() at appropriate places
gpio: em: Use irq_data_get_irq_chip_data() at appropriate places
...
Linus Torvalds [Tue, 2 Oct 2012 23:01:31 +0000 (16:01 -0700)]
workqueue: avoid using deprecated functions
The network merge brought in a few users of functions that got
deprecated by the workqueue cleanups: the 'system_nrt_wq' is now the
same as the regular system_wq, since all workqueues are now non-
reentrant.
Similarly, remove one use of flush_work_sync() - the regular
flush_work() has become synchronous, and the "_sync()" version is thus
deprecated as being superfluous.
2) Make SCTP more network namespace aware, from Eric Biederman.
3) TEAM driver now works with non-ethernet devices, from Jiri Pirko.
4) Make openvswitch network namespace aware, from Pravin B Shelar.
5) IPV6 NAT implementation, from Patrick McHardy.
6) Server side support for TCP Fast Open, from Jerry Chu and others.
7) Packet BPF filter supports MOD and XOR, from Eric Dumazet and Daniel
Borkmann.
8) Increate the loopback default MTU to 64K, from Eric Dumazet.
9) Use a per-task rather than per-socket page fragment allocator for
outgoing networking traffic. This benefits processes that have very
many mostly idle sockets, which is quite common.
From Eric Dumazet.
10) Use up to 32K for page fragment allocations, with fallbacks to
smaller sizes when higher order page allocations fail. Benefits are
a) less segments for driver to process b) less calls to page
allocator c) less waste of space.
From Eric Dumazet.
11) Allow GRO to be used on GRE tunnels, from Eric Dumazet.
12) VXLAN device driver, one way to handle VLAN issues such as the
limitation of 4096 VLAN IDs yet still have some level of isolation.
From Stephen Hemminger.
13) As usual there is a large boatload of driver changes, with the scale
perhaps tilted towards the wireless side this time around.
Fix up various fairly trivial conflicts, mostly caused by the user
namespace changes.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1012 commits)
hyperv: Add buffer for extended info after the RNDIS response message.
hyperv: Report actual status in receive completion packet
hyperv: Remove extra allocated space for recv_pkt_list elements
hyperv: Fix page buffer handling in rndis_filter_send_request()
hyperv: Fix the missing return value in rndis_filter_set_packet_filter()
hyperv: Fix the max_xfer_size in RNDIS initialization
vxlan: put UDP socket in correct namespace
vxlan: Depend on CONFIG_INET
sfc: Fix the reported priorities of different filter types
sfc: Remove EFX_FILTER_FLAG_RX_OVERRIDE_IP
sfc: Fix loopback self-test with separate_tx_channels=1
sfc: Fix MCDI structure field lookup
sfc: Add parentheses around use of bitfield macro arguments
sfc: Fix null function pointer in efx_sriov_channel_type
vxlan: virtual extensible lan
igmp: export symbol ip_mc_leave_group
netlink: add attributes to fdb interface
tg3: unconditionally select HWMON support when tg3 is enabled.
Revert "net: ti cpsw ethernet: allow reading phy interface mode from DT"
gre: fix sparse warning
...
Pull sparc updates from David Miller:
"Largely this is simply adding support for the Niagara 4 cpu.
Major areas are perf events (chip now supports 4 counters and can
monitor any event on each counter), crypto (opcodes are availble for
sha1, sha256, sha512, md5, crc32c, AES, DES, CAMELLIA, and Kasumi
although the last is unsupported since we lack a generic crypto layer
Kasumi implementation), and an optimized memcpy.
Finally some cleanups by Peter Senna Tschudin."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-next: (47 commits)
sparc64: Fix trailing whitespace in NG4 memcpy.
sparc64: Fix comment type in NG4 copy from user.
sparc64: Add SPARC-T4 optimized memcpy.
drivers/sbus/char: removes unnecessary semicolon
arch/sparc/kernel/pci_sun4v.c: removes unnecessary semicolon
sparc64: Fix function argument comment in camellia_sparc64_key_expand asm.
sparc64: Fix IV handling bug in des_sparc64_cbc_decrypt
sparc64: Add auto-loading mechanism to crypto-opcode drivers.
sparc64: Add missing pr_fmt define to crypto opcode drivers.
sparc64: Adjust crypto priorities.
sparc64: Use cpu_pgsz_mask for linear kernel mapping config.
sparc64: Probe cpu page size support more portably.
sparc64: Support 2GB and 16GB page sizes for kernel linear mappings.
sparc64: Fix bugs in unrolled 256-bit loops.
sparc64: Avoid code duplication in crypto assembler.
sparc64: Unroll CTR crypt loops in AES driver.
sparc64: Unroll ECB decryption loops in AES driver.
sparc64: Unroll ECB encryption loops in AES driver.
sparc64: Add ctr mode support to AES driver.
sparc64: Move AES driver over to a methods based implementation.
...
Haiyang Zhang [Tue, 2 Oct 2012 05:30:24 +0000 (05:30 +0000)]
hyperv: Add buffer for extended info after the RNDIS response message.
In some response messages, there may be some extended info after the
message.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com> Reviewed-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Haiyang Zhang [Tue, 2 Oct 2012 05:30:23 +0000 (05:30 +0000)]
hyperv: Report actual status in receive completion packet
The existing code always reports NVSP_STAT_SUCCESS. This patch adds the
mechanism to report failure when it happens.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com> Reviewed-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Haiyang Zhang [Tue, 2 Oct 2012 05:30:22 +0000 (05:30 +0000)]
hyperv: Remove extra allocated space for recv_pkt_list elements
The receive code path doesn't use the page buffer, so remove the
extra allocated space here.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com> Reviewed-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Haiyang Zhang [Tue, 2 Oct 2012 05:30:21 +0000 (05:30 +0000)]
hyperv: Fix page buffer handling in rndis_filter_send_request()
To prevent possible data corruption in RNDIS requests, add another
page buffer if the request message crossed page boundary.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com> Reviewed-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Haiyang Zhang [Tue, 2 Oct 2012 05:30:20 +0000 (05:30 +0000)]
hyperv: Fix the missing return value in rndis_filter_set_packet_filter()
Return ETIMEDOUT when the reply message is not received in time.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com> Reviewed-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Haiyang Zhang [Tue, 2 Oct 2012 05:30:19 +0000 (05:30 +0000)]
hyperv: Fix the max_xfer_size in RNDIS initialization
According to RNDIS specs, Windows sets this size to
0x4000. I use the same value here.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com> Reviewed-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Move vxlan UDP socket to correct network namespace
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Acked-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Tue, 2 Oct 2012 18:11:09 +0000 (11:11 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace
Pull user namespace changes from Eric Biederman:
"This is a mostly modest set of changes to enable basic user namespace
support. This allows the code to code to compile with user namespaces
enabled and removes the assumption there is only the initial user
namespace. Everything is converted except for the most complex of the
filesystems: autofs4, 9p, afs, ceph, cifs, coda, fuse, gfs2, ncpfs,
nfs, ocfs2 and xfs as those patches need a bit more review.
The strategy is to push kuid_t and kgid_t values are far down into
subsystems and filesystems as reasonable. Leaving the make_kuid and
from_kuid operations to happen at the edge of userspace, as the values
come off the disk, and as the values come in from the network.
Letting compile type incompatible compile errors (present when user
namespaces are enabled) guide me to find the issues.
The most tricky areas have been the places where we had an implicit
union of uid and gid values and were storing them in an unsigned int.
Those places were converted into explicit unions. I made certain to
handle those places with simple trivial patches.
Out of that work I discovered we have generic interfaces for storing
quota by projid. I had never heard of the project identifiers before.
Adding full user namespace support for project identifiers accounts
for most of the code size growth in my git tree.
Ultimately there will be work to relax privlige checks from
"capable(FOO)" to "ns_capable(user_ns, FOO)" where it is safe allowing
root in a user names to do those things that today we only forbid to
non-root users because it will confuse suid root applications.
While I was pushing kuid_t and kgid_t changes deep into the audit code
I made a few other cleanups. I capitalized on the fact we process
netlink messages in the context of the message sender. I removed
usage of NETLINK_CRED, and started directly using current->tty.
Some of these patches have also made it into maintainer trees, with no
problems from identical code from different trees showing up in
linux-next.
After reading through all of this code I feel like I might be able to
win a game of kernel trivial pursuit."
Fix up some fairly trivial conflicts in netfilter uid/git logging code.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace: (107 commits)
userns: Convert the ufs filesystem to use kuid/kgid where appropriate
userns: Convert the udf filesystem to use kuid/kgid where appropriate
userns: Convert ubifs to use kuid/kgid
userns: Convert squashfs to use kuid/kgid where appropriate
userns: Convert reiserfs to use kuid and kgid where appropriate
userns: Convert jfs to use kuid/kgid where appropriate
userns: Convert jffs2 to use kuid and kgid where appropriate
userns: Convert hpfs to use kuid and kgid where appropriate
userns: Convert btrfs to use kuid/kgid where appropriate
userns: Convert bfs to use kuid/kgid where appropriate
userns: Convert affs to use kuid/kgid wherwe appropriate
userns: On alpha modify linux_to_osf_stat to use convert from kuids and kgids
userns: On ia64 deal with current_uid and current_gid being kuid and kgid
userns: On ppc convert current_uid from a kuid before printing.
userns: Convert s390 getting uid and gid system calls to use kuid and kgid
userns: Convert s390 hypfs to use kuid and kgid where appropriate
userns: Convert binder ipc to use kuids
userns: Teach security_path_chown to take kuids and kgids
userns: Add user namespace support to IMA
userns: Convert EVM to deal with kuids and kgids in it's hmac computation
...
Linus Torvalds [Tue, 2 Oct 2012 17:52:28 +0000 (10:52 -0700)]
Merge branch 'for-3.7-hierarchy' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup
Pull cgroup hierarchy update from Tejun Heo:
"Currently, different cgroup subsystems handle nested cgroups
completely differently. There's no consistency among subsystems and
the behaviors often are outright broken.
People at least seem to agree that the broken hierarhcy behaviors need
to be weeded out if any progress is gonna be made on this front and
that the fallouts from deprecating the broken behaviors should be
acceptable especially given that the current behaviors don't make much
sense when nested.
This patch makes cgroup emit warning messages if cgroups for
subsystems with broken hierarchy behavior are nested to prepare for
fixing them in the future. This was put in a separate branch because
more related changes were expected (didn't make it this round) and the
memory cgroup wanted to pull in this and make changes on top."
* 'for-3.7-hierarchy' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cgroup: mark subsystems with broken hierarchy support and whine if cgroups are nested for them
Linus Torvalds [Tue, 2 Oct 2012 17:50:47 +0000 (10:50 -0700)]
Merge branch 'for-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup
Pull cgroup updates from Tejun Heo:
- xattr support added. The implementation is shared with tmpfs. The
usage is restricted and intended to be used to manage per-cgroup
metadata by system software. tmpfs changes are routed through this
branch with Hugh's permission.
- cgroup subsystem ID handling simplified.
* 'for-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cgroup: Define CGROUP_SUBSYS_COUNT according the configuration
cgroup: Assign subsystem IDs during compile time
cgroup: Do not depend on a given order when populating the subsys array
cgroup: Wrap subsystem selection macro
cgroup: Remove CGROUP_BUILTIN_SUBSYS_COUNT
cgroup: net_prio: Do not define task_netpioidx() when not selected
cgroup: net_cls: Do not define task_cls_classid() when not selected
cgroup: net_cls: Move sock_update_classid() declaration to cls_cgroup.h
cgroup: trivial fixes for Documentation/cgroups/cgroups.txt
xattr: mark variable as uninitialized to make both gcc and smatch happy
fs: add missing documentation to simple_xattr functions
cgroup: add documentation on extended attributes usage
cgroup: rename subsys_bits to subsys_mask
cgroup: add xattr support
cgroup: revise how we re-populate root directory
xattr: extract simple_xattr code from tmpfs
Linus Torvalds [Tue, 2 Oct 2012 16:54:49 +0000 (09:54 -0700)]
Merge branch 'for-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq
Pull workqueue changes from Tejun Heo:
"This is workqueue updates for v3.7-rc1. A lot of activities this
round including considerable API and behavior cleanups.
* delayed_work combines a timer and a work item. The handling of the
timer part has always been a bit clunky leading to confusing
cancelation API with weird corner-case behaviors. delayed_work is
updated to use new IRQ safe timer and cancelation now works as
expected.
* Another deficiency of delayed_work was lack of the counterpart of
mod_timer() which led to cancel+queue combinations or open-coded
timer+work usages. mod_delayed_work[_on]() are added.
These two delayed_work changes make delayed_work provide interface
and behave like timer which is executed with process context.
* A work item could be executed concurrently on multiple CPUs, which
is rather unintuitive and made flush_work() behavior confusing and
half-broken under certain circumstances. This problem doesn't
exist for non-reentrant workqueues. While non-reentrancy check
isn't free, the overhead is incurred only when a work item bounces
across different CPUs and even in simulated pathological scenario
the overhead isn't too high.
All workqueues are made non-reentrant. This removes the
distinction between flush_[delayed_]work() and
flush_[delayed_]_work_sync(). The former is now as strong as the
latter and the specified work item is guaranteed to have finished
execution of any previous queueing on return.
* In addition to the various bug fixes, Lai redid and simplified CPU
hotplug handling significantly.
* Joonsoo introduced system_highpri_wq and used it during CPU
hotplug.
There are two merge commits - one to pull in IRQ safe timer from
tip/timers/core and the other to pull in CPU hotplug fixes from
wq/for-3.6-fixes as Lai's hotplug restructuring depended on them."
Fixed a number of trivial conflicts, but the more interesting conflicts
were silent ones where the deprecated interfaces had been used by new
code in the merge window, and thus didn't cause any real data conflicts.
Tejun pointed out a few of them, I fixed a couple more.
* 'for-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq: (46 commits)
workqueue: remove spurious WARN_ON_ONCE(in_irq()) from try_to_grab_pending()
workqueue: use cwq_set_max_active() helper for workqueue_set_max_active()
workqueue: introduce cwq_set_max_active() helper for thaw_workqueues()
workqueue: remove @delayed from cwq_dec_nr_in_flight()
workqueue: fix possible stall on try_to_grab_pending() of a delayed work item
workqueue: use hotcpu_notifier() for workqueue_cpu_down_callback()
workqueue: use __cpuinit instead of __devinit for cpu callbacks
workqueue: rename manager_mutex to assoc_mutex
workqueue: WORKER_REBIND is no longer necessary for idle rebinding
workqueue: WORKER_REBIND is no longer necessary for busy rebinding
workqueue: reimplement idle worker rebinding
workqueue: deprecate __cancel_delayed_work()
workqueue: reimplement cancel_delayed_work() using try_to_grab_pending()
workqueue: use mod_delayed_work() instead of __cancel + queue
workqueue: use irqsafe timer for delayed_work
workqueue: clean up delayed_work initializers and add missing one
workqueue: make deferrable delayed_work initializer names consistent
workqueue: cosmetic whitespace updates for macro definitions
workqueue: deprecate system_nrt[_freezable]_wq
workqueue: deprecate flush[_delayed]_work_sync()
...
Rob Herring [Tue, 21 Aug 2012 10:26:24 +0000 (12:26 +0200)]
ARM: kill off arch_is_coherent
With ixp2xxx removed, there are no platforms that define arch_is_coherent,
so the last occurrences of arch_is_coherent can be removed. Any new
platform with coherent i/o should use coherent dma mapping functions.
Signed-off-by: Rob Herring <rob.herring@calxeda.com> Cc: Russell King <linux@arm.linux.org.uk> Cc: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Rob Herring [Tue, 21 Aug 2012 10:23:23 +0000 (12:23 +0200)]
ARM: add coherent iommu dma ops
Remove arch_is_coherent() from iommu dma ops and implement separate
coherent ops functions.
Signed-off-by: Rob Herring <rob.herring@calxeda.com> Cc: Russell King <linux@arm.linux.org.uk> Cc: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Rob Herring [Tue, 21 Aug 2012 10:20:17 +0000 (12:20 +0200)]
ARM: add coherent dma ops
arch_is_coherent is problematic as it is a global symbol. This
doesn't work for multi-platform kernels or platforms which can support
per device coherent DMA.
This adds arm_coherent_dma_ops to be used for devices which connected
coherently (i.e. to the ACP port on Cortex-A9 or A15). The arm_dma_ops
are modified at boot when arch_is_coherent is true.
Signed-off-by: Rob Herring <rob.herring@calxeda.com> Cc: Russell King <linux@arm.linux.org.uk> Cc: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
The dma_alloc_from_contiguous() function returns either a valid pointer
to a page structure or NULL, the error code set when pageno >= cma->count
is not used at all and can be safely removed.
This commit also changes the function to avoid goto and have only one exit
path and one place where mutex is unlocked.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
[fixed compilation break caused by missing semicolon] Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
This fixes a local merge conflict resolution done wrong locally in
arm-soc for-next. soc.h was added on a cleanup branch, but the driver
was moved and the header no longer needed.
Signed-off-by: Olof Johansson <olof@lixom.net>
[ .. and I did the same wrong merge, since git automatically does the
whole rename detection etc, so applying this patch from Olof - Linus ] Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Tue, 2 Oct 2012 02:11:38 +0000 (19:11 -0700)]
Merge tag 'multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM soc multiplatform enablement from Olof Johansson:
"This is a pretty significant branch. It's the introduction of the
first multiplatform support on ARM, and with this (and the later
branch) merged, it is now possible to build one kernel that contains
support for highbank, vexpress, mvebu, socfpga, and picoxcell. More
platforms will be convered over in the next few releases.
Two critical last things had to be done for this to be practical and
possible:
* Today each platform has its own include directory under
mach-<mach>/include/mach/*, and traditionally that is where a lot
of driver/platform shared definitions have gone, such as platform
data structures. They now need to move out to a common location
instead, and this branch moves a large number of those out to
include/linux/platform_data.
* Each platform used to list the device trees to compile for its
boards in mach-<mach>/Makefile.boot.
Both of the above changes will mean that there are some merge
conflicts to come (and some to resolve here). It's a one-time move
and once it settles in, we should be good for quite a while. Sorry
for the overhead."
Fix conflicts as per Olof.
* tag 'multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (51 commits)
ARM: add v7 multi-platform defconfig
ARM: msm: Move core.h contents into common.h
ARM: highbank: call highbank_pm_init from .init_machine
ARM: dtb: move all dtb targets to common Makefile
ARM: spear: move platform_data definitions
ARM: samsung: move platform_data definitions
ARM: orion: move platform_data definitions
ARM: vexpress: convert to multi-platform
ARM: initial multiplatform support
ARM: mvebu: move armada-370-xp.h in mach dir
ARM: vexpress: remove dependency on mach/* headers
ARM: picoxcell: remove dependency on mach/* headers
ARM: move all dtb targets out of Makefile.boot
ARM: picoxcell: move debug macros to include/debug
ARM: socfpga: move debug macros to include/debug
ARM: mvebu: move debug macros to include/debug
ARM: vexpress: move debug macros to include/debug
ARM: highbank: move debug macros to include/debug
ARM: move debug macros to common location
ARM: make mach/gpio.h headers optional
...
Linus Torvalds [Tue, 2 Oct 2012 01:56:31 +0000 (18:56 -0700)]
Merge tag 'docs' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM soc documentation updates from Olof Johansson:
"Documentation update for Marvell SoCs, the secret decoder ring to all
their crazy product names and numbers."
* tag 'docs' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
arm: add documentation describing Marvell families of SoC
Linus Torvalds [Tue, 2 Oct 2012 01:55:15 +0000 (18:55 -0700)]
Merge tag 'dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM soc device tree updates, take 2 from Olof Johansson:
"This branch contains mostly a set of changes for device tree bindings
on Samsung Exynos. It was staged behind the other branches due to
dependencies on pincontrol and board changes."
Fix up trivial conflict in drivers/clocksource/Makefile due to earlier
conflict resolution.
* tag 'dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: dts: Add nodes for dw_mmc controllers for Samsung EXYNOS5250 platforms
ARM: EXYNOS: Add AUXDATA support for MSHC controllers
ARM: EXYNOS: Add support for MSHC controller clocks
ARM: dts: Enable on-board keys as wakeup source for exynos4210-origen
ARM: dts: use uart2 for console on smdkv310 and smdk5250
ARM: dts: Add basic dts file for Samsung Trats board
ARM: EXYNOS: Add OF compatibility lookups for EXYNOS4 i2c adapters
ARM: dts: Specify address and size cells for i2c controllers for EXYNOS4
ARM: dts: Assume status of all optional nodes as disabled for exynos4
ARM: EXYNOS: Use exynos4 prefix instead of exynos4210 on exynos4-dt
ARM: dts: Move parts common to EXYNOS4 from exynos4210.dtsi to exynos4.dtsi
Linus Torvalds [Tue, 2 Oct 2012 01:48:30 +0000 (18:48 -0700)]
Merge tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM soc board specific updates from Olof Johansson:
"Misc board updates:
- Greg added a handful of boards to KS8695 (since he has stepped up
to maintain it).
- Qualcomm has added DT-only board support for a couple of their
newer SoCs.
- misc other updates for Samsung and Freescale boards."
Fix up trivial conflict in arch/arm/mach-shmobile/board-armadillo800eva.c
due to gpio device data being added next to hdmi device data that got moved.
* tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: msm: Allow 8960 and 8660 to compile together
ARM: msm: Allow msm_iomap-8x60 and msm_iomap-8960 to coexist
ARM: EXYNOS: Add generic PWM lookup support for SMDKV310
ARM: EXYNOS: Add generic PWM lookup support for SMDK4X12
ARM: EXYNOS: Use generic pwm driver in Origen board
ARM: shmobile: armadillo800eva: Add support RTC
ARM: ks8695: add board support for the OpenGear boards based on the KS8695
ARM: ks8695: add board support for the SnapGear boards based on the KS8695
ARM: dts: Add heartbeat gpio-leds support to Origen
ARM: dts: Use active low flag for gpio-keys on Origen
ARM: shmobile: marzen: enable thermal sensor
ARM: shmobile: marzen: fixup regulator id for smsc911x
ARM: shmobile: marzen: add SDHI0 support
ARM: mmp: enable debug uart port in defconfig
ARM: mmp: implement DEBUG_LL port choice
ARM: S3C64XX: Register audio platform devices for Bells on Cragganmore
ARM: S3C64XX: Update configuration for WM5102 module on Cragganmore
ARM: mx27pdk: Add audio support
ARM: ttc_dkb: add nand support
Linus Torvalds [Tue, 2 Oct 2012 01:46:13 +0000 (18:46 -0700)]
Merge tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM soc driver specific changes from Olof Johansson:
- A long-coming conversion of various platforms to a common LED
infrastructure
- AT91 is moved over to use the newer MCI driver for MMC
- Pincontrol conversions for samsung platforms
- DT bindings for gscaler on samsung
- i2c driver fixes for tegra, acked by i2c maintainer
Fix up conflicts as per Olof.
* tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (48 commits)
drivers: bus: omap_l3: use resources instead of hardcoded irqs
pinctrl: exynos: Fix wakeup IRQ domain registration check
pinctrl: samsung: Uninline samsung_pinctrl_get_soc_data
pinctrl: exynos: Correct the detection of wakeup-eint node
pinctrl: exynos: Mark exynos_irq_demux_eint as inline
pinctrl: exynos: Handle only unmasked wakeup interrupts
pinctrl: exynos: Fix typos in gpio/wkup _irq_mask
pinctrl: exynos: Set pin function to EINT in irq_set_type of GPIO EINTa
drivers: bus: Move the OMAP interconnect driver to drivers/bus/
i2c: tegra: dynamically control fast clk
i2c: tegra: I2_M_NOSTART functionality not supported in Tegra20
ARM: tegra: clock: remove unused clock entry for i2c
ARM: tegra: clock: add connection name in i2c clock entry
i2c: tegra: pass proper name for getting clock
ARM: tegra: clock: add i2c fast clock entry in clock table
ARM: EXYNOS: Adds G-Scaler device from Device Tree
ARM: EXYNOS: Add clock support for G-Scaler
ARM: EXYNOS: Enable pinctrl driver support for EXYNOS4 device tree enabled platform
ARM: dts: Add pinctrl node entries for SAMSUNG EXYNOS4210 SoC
ARM: EXYNOS: skip wakeup interrupt setup if pinctrl driver is used
...
Linus Torvalds [Tue, 2 Oct 2012 01:35:58 +0000 (18:35 -0700)]
Merge tag 'soc2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM soc-specific updates, take 2 from Olof Johansson:
"This branch converts the MXS Freescale platform to use irqdomains and
sparse IRQ, in preparation for DT probing and multiplatform kernels."
* tag 'soc2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: mxs: remove mach/irqs.h
ARM: mxs: select SPARSE_IRQ
ARM: mxs: adopt irq_domain support for icoll driver
ARM: mxs: select MULTI_IRQ_HANDLER
ARM: mxs: retrieve timer irq from device tree
gpio/mxs: adopt irq_domain support for mxs gpio driver
David S. Miller [Tue, 2 Oct 2012 01:32:55 +0000 (21:32 -0400)]
Merge branch 'for-davem' of git://git.kernel.org/pub/scm/linux/kernel/git/bwh/sfc-next
Ben Hutchings says:
====================
Some bug fixes that should go into 3.7:
1. Fix oops when removing device with SR-IOV enabled. (This regression
was introduced by the last set of changes, so the fix does not need to
be applied to any earlier kernel versions.)
2. Fix firmware structure field lookup bug that resulted in missing
sensor information.
3. Fix bug that makes self-test do very little in some configurations.
4. Fix the numbering of ethtool RX flow steering filters to reflect the
real hardware priorities.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
projects / karo-tx-linux.git / log