The array of unsigned long pointed by oops_page_used is allocated
by vmalloc which requires the size to be in bytes.
BITS_PER_LONG is equal to 32.
If we want to allocate memory for 32 pages with one bit per page then
32 / BITS_PER_LONG is equal to 1 byte that is 8 bits.
To fix it we need to multiply the result by sizeof(unsigned long) equal to 4.
Cc: stable@kernel.org Signed-off-by: Roman Tereshonkov <roman.tereshonkov@nokia.com> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Eric Sandeen [Tue, 6 Dec 2011 23:06:06 +0000 (17:06 -0600)]
jffs2: fix up error handling for insert_inode_locked
after 250df6ed274d767da844a5d9f05720b804240197
(fs: protect inode->i_state with inode->i_lock), insert_inode_locked()
no longer returns the inode with I_NEW set on failure. However,
the error handler still calls unlock_new_inode() on failure,
which does a WARN_ON if I_NEW is not set, so any failure spews
a lot of warnings.
We can just drop the unlock_new_inode() if insert_inode_locked()
fails here.
Signed-off-by: Eric Sandeen <sandeen@redhat.com> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Jonas Gorski [Mon, 5 Dec 2011 15:08:08 +0000 (16:08 +0100)]
mtd: maps: bcm963xx-flash: make CFE partition parsing an mtd parser
Recent BCM63XX devices support a variety of flash types (parallel, SPI,
NAND) and share the partition layout. To prevent code duplication make
the CFE partition parsing code a stand alone mtd parser to allow SPI or
NAND flash drivers to use it.
Liu Shuo [Sun, 4 Dec 2011 04:31:37 +0000 (12:31 +0800)]
mtd: nand: set correct length to FBCR for a non-full-page write
When we do a non-full-page write, the length be set to FBCR should
not be 'elbc_fcm_ctrl->index', it should be 'elbc_fcm_ctrl->index -
elbc_fcm_ctrl->column'.
Signed-off-by: Liu Shuo <b35362@freescale.com> Signed-off-by: Li Yang <leoli@freescale.com> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Liu Shuo [Sun, 4 Dec 2011 04:31:36 +0000 (12:31 +0800)]
mtd: nand: use elbc_fcm_ctrl->oob to set FPAR_MS bit of FPAR
On both of large-page chip and small-page chip, we always should use
'elbc_fcm_ctrl->oob' to set the FPAR_LP_MS/FPAR_SP_MS bit of FPAR, don't
use a overflowed 'column' to set it.
Signed-off-by: Liu Shuo <b35362@freescale.com> Signed-off-by: Li Yang <leoli@freescale.com> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Robert Jarzmik [Tue, 29 Nov 2011 22:16:35 +0000 (23:16 +0100)]
Documentation: add sysfs entries for mtd docg3 chips
Add documentation for MSystems disk-on-chip docg3 chips
sysfs entries, which enable and disable protection areas,
giving or disabling access to the chip's memory.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Dan Carpenter [Mon, 28 Nov 2011 13:53:13 +0000 (16:53 +0300)]
mtd: docg3: dereferencing an ERR_PTR() in docg3_probe()
If doc_probe_device() returned an ERR_PTR, then we accidentally saved
that to docg3_floors[floor] = mtd; which gets derefenced in the error
handling when we call doc_release_device().
I've reworked the error handling to take care of that and hopefully
make it a little simpler.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
mtd: Remove redundant spi driver bus initialization
In ancient times it was necessary to manually initialize the bus field of an
spi_driver to spi_bus_type. These days this is done in spi_driver_register(),
so we can drop the manual assignment.
The patch was generated using the following coccinelle semantic patch:
// <smpl>
@@
identifier _driver;
@@
struct spi_driver _driver = {
.driver = {
- .bus = &spi_bus_type,
},
};
// </smpl>
Wolfram Sang [Wed, 23 Nov 2011 14:57:06 +0000 (15:57 +0100)]
mtd: gpmi: add missing include 'module.h'
Fixes:
drivers/mtd/nand/gpmi-nand/gpmi-nand.c: In function 'gpmi_nfc_init':
drivers/mtd/nand/gpmi-nand/gpmi-nand.c:1475:16: error: 'THIS_MODULE' undeclared (first use in this function)
drivers/mtd/nand/gpmi-nand/gpmi-nand.c:1475:16: note: each undeclared identifier is reported only once for each function it appears in
drivers/mtd/nand/gpmi-nand/gpmi-nand.c: At top level:
drivers/mtd/nand/gpmi-nand/gpmi-nand.c:1617:15: error: expected declaration specifiers or '...' before string constant
drivers/mtd/nand/gpmi-nand/gpmi-nand.c:1617:1: warning: data definition has no type or storage class
drivers/mtd/nand/gpmi-nand/gpmi-nand.c:1617:1: warning: type defaults to 'int' in declaration of 'MODULE_AUTHOR'
Robert Jarzmik [Sat, 19 Nov 2011 15:02:58 +0000 (16:02 +0100)]
mtd: docg3: add protection areas sysfs access
As each docg3 chip has 2 protection areas (DPS0 and DPS1),
and because theses areas can prevent user access to the chip
data, add for each floor the sysfs entries which insert the
protection key into the right DPS.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr> Reviewed-by: Ivan Djelic <ivan.djelic@parrot.com> Reviewed-by: Mike Dunn <mikedunn@newsguy.com>
Robert Jarzmik [Sat, 19 Nov 2011 15:02:57 +0000 (16:02 +0100)]
mtd: docg3: add fast mode
Docg3 chips can work in 3 modes : normal MLC mode, fast
mode and reliable mode. Normally, as docg3 is a MLC chip, it
should be configured to work in normal mode.
In both normal mode, each page is distinct. This
means that writing to page 12 of blocks 14,15 writes only to
that page, and reading from page 12 of blocks 14,15 reads
only from that page.
In reliable and fast modes, pages are coupled by pairs, and
are clones one of each other. This means that the available
capacity of the chip is halved. Pages are coupled in each
block, and page of index 2*n contains the same data as page
2*n+1 of the same block.
In fast mode, the reads occur a bit faster, but are a bit
less reliable that in normal mode.
When reading from page 2*n, the chip reads bytes from both
page 2*n and page 2*n+1, makes a logical and for each byte,
and returns the result. As programming a page means
"clearing bits", even if a bit was not cleared on one page
because the flash is worn out, the other page has the bit
cleared, and the result of the "AND" gives a correct result.
When writing to page 2*n, the chip writes data to both page
2*n and page 2*n+1.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr> Reviewed-by: Ivan Djelic <ivan.djelic@parrot.com> Reviewed-by: Mike Dunn <mikedunn@newsguy.com>
Robert Jarzmik [Sat, 19 Nov 2011 15:02:55 +0000 (16:02 +0100)]
mtd: docg3: add ECC correction code
Credit for discovering the BCH algorith parameters, and bit
reversing algorithm is to be give to Mike Dunn and Ivan
Djelic.
The BCH correction code relied upon the BCH library, where
all data and ECC is bit-reversed. The BCH library works
correctly when each input byte is bit-reversed, and
accordingly ECC output is also bit-reversed.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr> Reviewed-by: Ivan Djelic <ivan.djelic@parrot.com> Reviewed-by: Mike Dunn <mikedunn@newsguy.com>
Robert Jarzmik [Sat, 19 Nov 2011 15:02:53 +0000 (16:02 +0100)]
mtd: docg3: add erase functions
Add erase capability to the docg3 driver. The erase block is
made of 2 physical blocks, as both share all 64 pages. That
makes an erase block of at least 64 kBytes.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr> Reviewed-by: Ivan Djelic <ivan.djelic@parrot.com> Reviewed-by: Mike Dunn <mikedunn@newsguy.com>
Robert Jarzmik [Sat, 19 Nov 2011 15:02:52 +0000 (16:02 +0100)]
mtd: docg3: add write functions
Add write capability to the docg3 driver. The writes are
possible on a single page (512 bytes + 16 bytes), even if
that page is split on 2 physical pages on 2 blocks (each on
one plane).
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr> Reviewed-by: Ivan Djelic <ivan.djelic@parrot.com> Reviewed-by: Mike Dunn <mikedunn@newsguy.com>
Robert Jarzmik [Sat, 19 Nov 2011 15:02:48 +0000 (16:02 +0100)]
mtd: docg3: add multiple floor support
Add support for multiple floors, ie. cascaded docg3
chips. There might be 4 docg3 chips cascaded, sharing the
same address space, and providing up to 4 times the storage
capacity of a unique chip.
Each floor will be seen as an independant mtd device.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr> Reviewed-by: Ivan Djelic <ivan.djelic@parrot.com> Reviewed-by: Mike Dunn <mikedunn@newsguy.com>
Robert Jarzmik [Sat, 19 Nov 2011 15:02:47 +0000 (16:02 +0100)]
mtd: docg3: fix reading oob+data without correction
Fix the docg3 reads to be able to cope with all possible
data buffer / oob buffer / file mode combinations from
docg3_read_oob().
This especially ensures that raw reads do not use ECC
corrections, and AUTOOOB and PLACEOOB do use ECC
correction.
The approach is to empty docg3_read() and make it a wrapper
to docg3_read_oob(). As docg3_read_oob() handles all the
funny cases (no data buffer but oob buffer, data buffer but
no oob buffer, ...), docg3_read() is just a special use of
docg3_read_oob().
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr> Reviewed-by: Ivan Djelic <ivan.djelic@parrot.com> Reviewed-by: Mike Dunn <mikedunn@newsguy.com>
Robert Jarzmik [Sat, 19 Nov 2011 15:02:45 +0000 (16:02 +0100)]
mtd: docg3: fix protection areas reading
The protection areas boundaries were on 16bit registers, not
8bit. This is consistent with block numbers, which can
extend up to 4096 on bigger chips (and is 2048 on the
docg3).
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr> Reviewed-by: Ivan Djelic <ivan.djelic@parrot.com> Reviewed-by: Mike Dunn <mikedunn@newsguy.com>
projects / karo-tx-linux.git / log