NeilBrown [Thu, 17 Jun 2010 07:41:03 +0000 (17:41 +1000)]
md/raid5: add a missing 'continue' in a loop.
As the comment says, the tail of this loop only applies to devices
that are not fully in sync, so if In_sync was set, we should avoid
the rest of the loop.
This bug will hardly ever cause an actual problem. The worst it
can do is allow an array to be assembled that is dirty and degraded,
which is not generally a good idea (without warning the sysadmin
first).
This will only happen if the array is RAID4 or a RAID5/6 in an
intermediate state during a reshape and so has one drive that is
all 'parity' - no data - while some other device has failed.
This is certainly possible, but not at all common.
NeilBrown [Thu, 17 Jun 2010 07:25:21 +0000 (17:25 +1000)]
md/raid5: Allow recovered part of partially recovered devices to be in-sync
During a recovery of reshape the early part of some devices might be
in-sync while the later parts are not.
We we know we are looking at an early part it is good to treat that
part as in-sync for stripe calculations.
This is particularly important for a reshape which suffers device
failure. Treating the data as in-sync can mean the difference between
data-safety and data-loss.
NeilBrown [Wed, 16 Jun 2010 07:17:53 +0000 (17:17 +1000)]
md/raid5: More careful check for "has array failed".
When we are reshaping an array, the device failure combinations
that cause us to decide that the array as failed are more subtle.
In particular, any 'spare' will be fully in-sync in the section
of the array that has already been reshaped, thus failures that
affect only that section are less critical.
So encode this subtlety in a new function and call it as appropriate.
The case that showed this problem was a 4 drive RAID5 to 8 drive RAID6
conversion where the last two devices failed.
This resulted in:
good good good good incomplete good good failed failed
while converting a 5-drive RAID6 to 8 drive RAID5
The incomplete device causes the whole array to look bad,
bad as it was actually good for the section that had been
converted to 8-drives, all the data was actually safe.
Reported-by: Terry Morris <tbmorris@tbmorris.com> Signed-off-by: NeilBrown <neilb@suse.de>
NeilBrown [Wed, 16 Jun 2010 07:01:25 +0000 (17:01 +1000)]
md: Don't update ->recovery_offset when reshaping an array to fewer devices.
When an array is reshaped to have fewer devices, the reshape proceeds
from the end of the devices to the beginning.
If a device happens to be non-In_sync (which is possible but rare)
we would normally update the ->recovery_offset as the reshape
progresses. However that would be wrong as the recover_offset records
that the early part of the device is in_sync, while in fact it would
only be the later part that is in_sync, and in any case the offset
number would be measured from the wrong end of the device.
Relatedly, if after a reshape a spare is discovered to not be
recoverred all the way to the end, not allow spare_active
to incorporate it in the array.
This becomes relevant in the following sample scenario:
A 4 drive RAID5 is converted to a 6 drive RAID6 in a combined
operation.
The RAID5->RAID6 conversion will cause a 5 drive to be included as a
spare, then the 5drive -> 6drive reshape will effectively rebuild that
spare as it progresses. The 6th drive is treated as in_sync the whole
time as there is never any case that we might consider reading from
it, but must not because there is no valid data.
If we interrupt this reshape part-way through and reverse it to return
to a 5-drive RAID6 (or event a 4-drive RAID5), we don't want to update
the recovery_offset - as that would be wrong - and we don't want to
include that spare as active in the 5-drive RAID6 when the reversed
reshape completed and it will be mostly out-of-sync still.
NeilBrown [Wed, 16 Jun 2010 06:45:16 +0000 (16:45 +1000)]
md/raid5: avoid oops when number of devices is reduced then increased.
The entries in the stripe_cache maintained by raid5 are enlarged
when we increased the number of devices in the array, but not
shrunk when we reduce the number of devices.
So if entries are added after reducing the number of devices, we
much ensure to initialise the whole entry, not just the part that
is currently relevant. Otherwise if we enlarge the array again,
we will reference uninitialised values.
As grow_buffers/shrink_buffer now want to use a count that is stored
explicity in the raid_conf, they should get it from there rather than
being passed it as a parameter.
NeilBrown [Tue, 15 Jun 2010 08:36:03 +0000 (09:36 +0100)]
md: fix handling of array level takeover that re-arranges devices.
Most array level changes leave the list of devices largely unchanged,
possibly causing one at the end to become redundant.
However conversions between RAID0 and RAID10 need to renumber
all devices (except 0).
This renumbering is currently being done in the ->run method when the
new personality takes over. However this is too late as the common
code in md.c might already have invalidated some of the devices if
they had a ->raid_disk number that appeared to high.
Moving it into the ->takeover method is too early as the array is
still active at that time and wrong ->raid_disk numbers could cause
confusion.
So add a ->new_raid_disk field to mdk_rdev_s and use it to communicate
the new raid_disk number.
Now the common code knows exactly which devices need to be renumbered,
and which can be invalidated, and can do it all at a convenient time
when the array is suspend.
It can also update some symlinks in sysfs which previously were not be
updated correctly.
Reported-by: Maciej Trela <maciej.trela@intel.com> Signed-off-by: NeilBrown <neilb@suse.de>
md: raid10: Fix null pointer dereference in fix_read_error()
Such NULL pointer dereference can occur when the driver was fixing the
read errors/bad blocks and the disk was physically removed
causing a system crash. This patch check if the
rcu_dereference() returns valid rdev before accessing it in fix_read_error().
Cc: stable@kernel.org Signed-off-by: Prasanna S. Panchamukhi <prasanna.panchamukhi@riverbed.com> Signed-off-by: Rob Becker <rbecker@riverbed.com> Signed-off-by: NeilBrown <neilb@suse.de>
The logic was almost right. However if revalidate_disk is called
when the device is not yet open, bdev->bd_disk won't be set, so the
flush_disk() Call will not set bd_invalidated.
So when md_open is called we still need to ensure that
->bd_invalidated gets set. This is easily done with a call to
check_disk_size_change in the place where the offending commit removed
check_disk_change. At the important times, the size will have changed
from 0 to non-zero, so check_disk_size_change will set bd_invalidated.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
wimax/i2400m: fix missing endian correction read in fw loader
net8139: fix a race at the end of NAPI
pktgen: Fix accuracy of inter-packet delay.
pkt_sched: gen_estimator: add a new lock
net: deliver skbs on inactive slaves to exact matches
ipv6: fix ICMP6_MIB_OUTERRORS
r8169: fix mdio_read and update mdio_write according to hw specs
gianfar: Revive the driver for eTSEC devices (disable timestamping)
caif: fix a couple range checks
phylib: Add support for the LXT973 phy.
net: Print num_rx_queues imbalance warning only when there are allocated queues
Linus Torvalds [Fri, 11 Jun 2010 21:18:47 +0000 (14:18 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable:
Btrfs: The file argument for fsync() is never null
Btrfs: handle ERR_PTR from posix_acl_from_xattr()
Btrfs: avoid BUG when dropping root and reference in same transaction
Btrfs: prohibit a operation of changing acl's mask when noacl mount option used
Btrfs: should add a permission check for setfacl
Btrfs: btrfs_lookup_dir_item() can return ERR_PTR
Btrfs: btrfs_read_fs_root_no_name() returns ERR_PTRs
Btrfs: unwind after btrfs_start_transaction() errors
Btrfs: btrfs_iget() returns ERR_PTR
Btrfs: handle kzalloc() failure in open_ctree()
Btrfs: handle error returns from btrfs_lookup_dir_item()
Btrfs: Fix BUG_ON for fs converted from extN
Btrfs: Fix null dereference in relocation.c
Btrfs: fix remap_file_pages error
Btrfs: uninitialized data is check_path_shared()
Btrfs: fix fallocate regression
Btrfs: fix loop device on top of btrfs
Linus Torvalds [Fri, 11 Jun 2010 21:15:44 +0000 (14:15 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI: clear bridge resource range if BIOS assigned bad one
PCI: hotplug/cpqphp, fix NULL dereference
Revert "PCI: create function symlinks in /sys/bus/pci/slots/N/"
PCI: change resource collision messages from KERN_ERR to KERN_INFO
Yinghai Lu [Thu, 3 Jun 2010 20:43:03 +0000 (13:43 -0700)]
PCI: clear bridge resource range if BIOS assigned bad one
Yannick found that video does not work with 2.6.34. The cause of this
bug was that the BIOS had assigned the wrong range to the PCI bridge
above the video device. Before 2.6.34 the kernel would have shrunk
the size of the bridge window, but since d65245c PCI: don't shrink bridge resources
the kernel will avoid shrinking BIOS ranges.
So zero out the old range if we fail to claim it at boot time; this will
cause us to allocate a new range at startup, restoring the 2.6.34
behavior.
Jiri Slaby [Wed, 9 Jun 2010 20:31:13 +0000 (22:31 +0200)]
PCI: hotplug/cpqphp, fix NULL dereference
There are devices out there which are PCI Hot-plug controllers with
compaq PCI IDs, but are not bridges, hence have pdev->subordinate
NULL. But cpqphp expects the pointer to be non-NULL.
Add a check to the probe function to avoid oopses like:
BUG: unable to handle kernel NULL pointer dereference at 00000050
IP: [<f82e3c41>] cpqhpc_probe+0x951/0x1120 [cpqphp]
*pdpt = 0000000033779001 *pde = 0000000000000000
...
Bjorn Helgaas [Thu, 3 Jun 2010 19:47:18 +0000 (13:47 -0600)]
PCI: change resource collision messages from KERN_ERR to KERN_INFO
We can often deal with PCI resource issues by moving devices around. In
that case, there's no point in alarming the user with messages like these.
There are many bug reports where the message itself is the only problem,
e.g., https://bugs.launchpad.net/ubuntu/+source/linux/+bug/413419 .
Dan Carpenter [Sat, 29 May 2010 09:49:07 +0000 (09:49 +0000)]
Btrfs: The file argument for fsync() is never null
The "file" argument for fsync is never null so we can remove this check.
What drew my attention here is that 7ea8085910e: "drop unused dentry
argument to ->fsync" introduced an unconditional dereference at the
start of the function and that generated a smatch warning.
Signed-off-by: Dan Carpenter <error27@gmail.com> Signed-off-by: Chris Mason <chris.mason@oracle.com>
Sage Weil [Mon, 17 May 2010 17:15:27 +0000 (17:15 +0000)]
Btrfs: avoid BUG when dropping root and reference in same transaction
If btrfs_ioctl_snap_destroy() deletes a snapshot but finishes
with end_transaction(), the cleaner kthread may come in and
drop the root in the same transaction. If that's the case, the
root's refs still == 1 in the tree when btrfs_del_root() deletes
the item, because commit_fs_roots() hasn't updated it yet (that
happens during the commit).
This wasn't a problem before only because
btrfs_ioctl_snap_destroy() would commit the transaction before dropping
the dentry reference, so the dead root wouldn't get queued up until
after the fs root item was updated in the btree.
Since it is not an error to drop the root reference and the root in the
same transaction, just drop the BUG_ON() in btrfs_del_root().
Signed-off-by: Sage Weil <sage@newdream.net> Signed-off-by: Chris Mason <chris.mason@oracle.com>
Shi Weihua [Tue, 18 May 2010 00:51:54 +0000 (00:51 +0000)]
Btrfs: prohibit a operation of changing acl's mask when noacl mount option used
when used Posix File System Test Suite(pjd-fstest) to test btrfs,
some cases about setfacl failed when noacl mount option used.
I simplified used commands in pjd-fstest, and the following steps
can reproduce it.
------------------------
# cd btrfs-part/
# mkdir aaa
# setfacl -m m::rw aaa <- successed, but not expected by pjd-fstest.
------------------------
I checked ext3, a warning message occured, like as:
setfacl: aaa/: Operation not supported
Certainly, it's expected by pjd-fstest.
So, i compared acl.c of btrfs and ext3. Based on that, a patch created.
Fortunately, it works.
Signed-off-by: Shi Weihua <shiwh@cn.fujitsu.com> Signed-off-by: Chris Mason <chris.mason@oracle.com>
Shi Weihua [Tue, 18 May 2010 00:50:32 +0000 (00:50 +0000)]
Btrfs: should add a permission check for setfacl
On btrfs, do the following
------------------
# su user1
# cd btrfs-part/
# touch aaa
# getfacl aaa
# file: aaa
# owner: user1
# group: user1
user::rw-
group::rw-
other::r--
# su user2
# cd btrfs-part/
# setfacl -m u::rwx aaa
# getfacl aaa
# file: aaa
# owner: user1
# group: user1
user::rwx <- successed to setfacl
group::rw-
other::r--
------------------
but we should prohibit it that user2 changing user1's acl.
In fact, on ext3 and other fs, a message occurs:
setfacl: aaa: Operation not permitted
This patch fixed it. Signed-off-by: Shi Weihua <shiwh@cn.fujitsu.com> Signed-off-by: Chris Mason <chris.mason@oracle.com>
btrfs_read_fs_root_no_name() returns ERR_PTRs on error so I added a
check for that. It's not clear to me if it can also return NULL
pointers or not so I left the original NULL pointer check as is.
Signed-off-by: Dan Carpenter <error27@gmail.com> Signed-off-by: Chris Mason <chris.mason@oracle.com>
Dan Carpenter [Sat, 29 May 2010 09:46:47 +0000 (09:46 +0000)]
Btrfs: unwind after btrfs_start_transaction() errors
This was added by a22285a6a3: "Btrfs: Integrate metadata reservation
with start_transaction". If we goto out here then we skip all the
unwinding and there are locks still held etc.
Signed-off-by: Dan Carpenter <error27@gmail.com> Signed-off-by: Chris Mason <chris.mason@oracle.com>
Linus Torvalds [Fri, 11 Jun 2010 16:55:50 +0000 (09:55 -0700)]
Merge branch 'rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild-2.6
* 'rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild-2.6:
kbuild: Create output directory in Makefile.modbuiltin
kbuild: Generate modules.builtin in make modules
Linus Torvalds [Fri, 11 Jun 2010 16:55:21 +0000 (09:55 -0700)]
Merge branch 'urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia-2.6
* 'urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia-2.6:
pcmcia: avoid validate_cis failure on CIS override
pcmcia: dev_node removal bugfix
pcmcia: yenta_socket.c Remove extra #ifdef CONFIG_YENTA_TI
pcmcia: only keep saved I365_CSCINT flag if there is no PCI irq
Linus Torvalds [Fri, 11 Jun 2010 16:52:23 +0000 (09:52 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
ceph: try to send partial cap release on cap message on missing inode
ceph: release cap on import if we don't have the inode
ceph: fix misleading/incorrect debug message
ceph: fix atomic64_t initialization on ia64
ceph: fix lease revocation when seq doesn't match
ceph: fix f_namelen reported by statfs
ceph: fix memory leak in statfs
ceph: fix d_subdirs ordering problem
Dan Carpenter [Tue, 1 Jun 2010 08:23:11 +0000 (08:23 +0000)]
Btrfs: uninitialized data is check_path_shared()
refs can be used with uninitialized data if btrfs_lookup_extent_info()
fails on the first pass through the loop. In the original code if that
happens then check_path_shared() probably returns 1, this patch
changes it to return 1 for safety.
Signed-off-by: Dan Carpenter <error27@gmail.com> Signed-off-by: Chris Mason <chris.mason@oracle.com>
Josef Bacik [Mon, 7 Jun 2010 18:26:37 +0000 (18:26 +0000)]
Btrfs: fix fallocate regression
Seems that when btrfs_fallocate was converted to use the new ENOSPC stuff we
dropped passing the mode to the function that actually does the preallocation.
This breaks anybody who wants to use FALLOC_FL_KEEP_SIZE. Thanks,
Signed-off-by: Josef Bacik <josef@redhat.com> Signed-off-by: Chris Mason <chris.mason@oracle.com>
Daniel Turull [Fri, 11 Jun 2010 06:08:11 +0000 (23:08 -0700)]
pktgen: Fix accuracy of inter-packet delay.
This patch correct a bug in the delay of pktgen.
It makes sure the inter-packet interval is accurate.
Signed-off-by: Daniel Turull <daniel.turull@gmail.com> Signed-off-by: Robert Olsson <robert.olsson@its.uu.se> Signed-off-by: David S. Miller <davem@davemloft.net>
John Fastabend [Thu, 3 Jun 2010 09:30:11 +0000 (09:30 +0000)]
net: deliver skbs on inactive slaves to exact matches
Currently, the accelerated receive path for VLAN's will
drop packets if the real device is an inactive slave and
is not one of the special pkts tested for in
skb_bond_should_drop(). This behavior is different then
the non-accelerated path and for pkts over a bonded vlan.
For example,
vlanx -> bond0 -> ethx
will be dropped in the vlan path and not delivered to any
packet handlers at all. However,
bond0 -> vlanx -> ethx
and
bond0 -> ethx
will be delivered to handlers that match the exact dev,
because the VLAN path checks the real_dev which is not a
slave and netif_recv_skb() doesn't drop frames but only
delivers them to exact matches.
This patch adds a sk_buff flag which is used for tagging
skbs that would previously been dropped and allows the
skb to continue to skb_netif_recv(). Here we add
logic to check for the deliver_no_wcard flag and if it
is set only deliver to handlers that match exactly. This
makes both paths above consistent and gives pkt handlers
a way to identify skbs that come from inactive slaves.
Without this patch in some configurations skbs will be
delivered to handlers with exact matches and in others
be dropped out right in the vlan path.
I have tested the following 4 configurations in failover modes
and load balancing modes.
# bond0 -> ethx
# vlanx -> bond0 -> ethx
# bond0 -> vlanx -> ethx
# bond0 -> ethx
|
vlanx -> --
Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sage Weil [Wed, 9 Jun 2010 23:52:04 +0000 (16:52 -0700)]
ceph: try to send partial cap release on cap message on missing inode
If we have enough memory to allocate a new cap release message, do so, so
that we can send a partial release message immediately. This keeps us from
making the MDS wait when the cap release it needs is in a partially full
release message.
If we fail because of ENOMEM, oh well, they'll just have to wait a bit
longer.
Sage Weil [Wed, 9 Jun 2010 23:47:10 +0000 (16:47 -0700)]
ceph: release cap on import if we don't have the inode
If we get an IMPORT that give us a cap, but we don't have the inode, queue
a release (and try to send it immediately) so that the MDS doesn't get
stuck waiting for us.
Catalin Marinas [Thu, 10 Jun 2010 16:02:12 +0000 (17:02 +0100)]
sata_sil24: Use memory barriers before issuing commands
The data in the cmd_block buffers may reach the main memory after the
writel() to the device ports. This patch introduces two calls to wmb()
to ensure the relative ordering.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Tested-by: Colin Tuckley <colin.tuckley@arm.com> Cc: Tejun Heo <tj@kernel.org> Cc: Jeff Garzik <jeff@garzik.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Dan Carpenter [Wed, 9 Jun 2010 12:01:54 +0000 (14:01 +0200)]
sata_sil24: memset() overflow
cb->atapi.cdb is an array of 16 u8 elements. The call too memset()
would set the first part of the sge array to zero as well. It's not
a packed struct.
This one has been around for five years. I found it with Smatch. I
think the reason no one has seen it before is because we normally call
sil24_fill_sg() and that overwrites sge with proper information?
Signed-off-by: Dan Carpenter <error27@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Linus Torvalds [Thu, 10 Jun 2010 17:53:14 +0000 (10:53 -0700)]
Merge branch 'kvm-updates/2.6.35' of git://git.kernel.org/pub/scm/virt/kvm/kvm
* 'kvm-updates/2.6.35' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: read apic->irr with ioapic lock held
KVM: ia64: Add missing spin_unlock in kvm_arch_hardware_enable()
KVM: Fix order passed to iommu_unmap
KVM: MMU: Remove user access when allowing kernel access to gpte.w=0 page
KVM: MMU: invalidate and flush on spte small->large page size change
KVM: SVM: Implement workaround for Erratum 383
KVM: SVM: Handle MCEs early in the vmexit process
KVM: powerpc: fix init/exit annotation
Nick Piggin [Tue, 25 May 2010 15:51:19 +0000 (01:51 +1000)]
block: bd_start_claiming cleanup
I don't like the subtle multi-context code in bd_claim (ie. detects where it
has been called based on bd_claiming). It seems clearer to just require a new
function to finish a 2-part claim.
Also improve commentary in bd_start_claiming as to how it should
be used.
Linus Torvalds [Thu, 10 Jun 2010 16:34:15 +0000 (09:34 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: sound/spi: patch for the unuseful variable removal
ALSA: hda - Add SSID table for iMac7,1.
ALSA: hda - Add SSID table for MacBookAir1,1
ALSA: hda - Add SSID table for MacBookAir2,1
ALSA: atmel: set "channel A event" output to debug
Linus Torvalds [Thu, 10 Jun 2010 16:30:09 +0000 (09:30 -0700)]
Merge branch 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
tracing: Fix null pointer deref with SEND_SIG_FORCED
perf: Fix signed comparison in perf_adjust_period()
powerpc/oprofile: fix potential buffer overrun in op_model_cell.c
perf symbols: Set the DSO long name when using symbol_conf.vmlinux_name
Linus Torvalds [Thu, 10 Jun 2010 14:35:41 +0000 (07:35 -0700)]
Merge master.kernel.org:/home/rmk/linux-2.6-arm
* master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: 6164/1: Add kto and kfrom to input operands list.
ARM: 6166/1: Proper prefetch abort handling on pre-ARMv6
ARM: 6165/1: trap overflows on highmem pages from kmap_atomic when debugging
ARM: 6152/1: ux500 make it possible to disable localtimers
[ARM] pxa/spitz: Correctly register WM8750
[ARM] pxa/palmtc: storage class should be before const qualifier
ARM: 6146/1: sa1111: Prevent deadlock in resume path
ARM: 6145/1: ux500 MTU clockrate correction
ARM: 6144/1: TCM memory bug freeing bug
ARM: VFP: Fix vfp_put_double() for d16-d31
Timo Teräs [Thu, 10 Jun 2010 00:31:48 +0000 (17:31 -0700)]
r8169: fix mdio_read and update mdio_write according to hw specs
Realtek confirmed that a 20us delay is needed after mdio_read and
mdio_write operations. Reduce the delay in mdio_write, and add it
to mdio_read too. Also add a comment that the 20us is from hw specs.
Signed-off-by: Timo Teräs <timo.teras@iki.fi> Acked-by: Francois Romieu <romieu@fr.zoreil.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Anton Vorontsov [Wed, 9 Jun 2010 23:27:08 +0000 (16:27 -0700)]
gianfar: Revive the driver for eTSEC devices (disable timestamping)
Since commit cc772ab7cdcaa24d1fae332d92a1602788644f7a ("gianfar: Add
hardware RX timestamping support"), the driver no longer works on
at least MPC8313ERDB and MPC8568EMDS boards (and possibly much more
boards as well).
That's how MPC8313 Reference Manual describes RCTRL_TS_ENABLE bit:
Timestamp incoming packets as padding bytes. PAL field is set
to 8 if the PAL field is programmed to less than 8. Must be set
to zero if TMR_CTRL[TE]=0.
I see that the commit above sets this bit, but it doesn't handle
TMR_CTRL. Manfred probably had this bit set by the firmware for
his boards. But obviously this isn't true for all boards in the
wild.
Also, I recall that Freescale BSPs were explicitly disabling the
timestamping because of a performance drop.
For now, the best way to deal with this is just disable the
timestamping, and later we can discuss proper device tree bindings
and implement enabling this feature via some property.
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Mon, 7 Jun 2010 04:51:58 +0000 (04:51 +0000)]
caif: fix a couple range checks
The extra ! character means that these conditions are always false.
Signed-off-by: Dan Carpenter <error27@gmail.com> Acked-by: Sjur Braendeland <sjur.brandeland@stericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Richard Cochran [Mon, 7 Jun 2010 05:39:32 +0000 (05:39 +0000)]
phylib: Add support for the LXT973 phy.
This patch implements a work around for Erratum 5, "3.3 V Fiber Speed
Selection." If the hardware wiring does not respect this erratum, then
fiber optic mode will not work properly.
Signed-off-by: Richard Cochran <richard.cochran@omicron.at> Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Marek [Mon, 7 Jun 2010 20:22:12 +0000 (22:22 +0200)]
kbuild: Generate modules.builtin in make modules
Generating the file in make modules_install was broken as well, because
it didn't work in a readonly filesystem and otherwise it generated a
root-owned file which is not wanted.
Reported-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Michal Marek <mmarek@suse.cz>
Tim Gardner [Tue, 8 Jun 2010 23:51:27 +0000 (17:51 -0600)]
net: Print num_rx_queues imbalance warning only when there are allocated queues
BugLink: http://bugs.launchpad.net/bugs/591416
There are a number of network drivers (bridge, bonding, etc) that are not yet
receive multi-queue enabled and use alloc_netdev(), so don't print a
num_rx_queues imbalance warning in that case.
Also, only print the warning once for those drivers that _are_ multi-queue
enabled.
Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (21 commits)
mac80211: fix deauth before assoc
iwlwifi: add missing rcu_read_lock
mac80211: fix function pointer check
wireless: remove my name from the maintainer list
ath5k: fix NULL pointer in antenna configuration
p54usb: Add device ID for Dell WLA3310 USB
wl1251: fix a memory leak in probe
ipmr: dont corrupt lists
8139too: fix buffer overrun in rtl8139_init_board
asix: check packet size against mtu+ETH_HLEN instead of ETH_FRAME_LEN
r8169: fix random mdio_write failures
ip6mr: fix a typo in ip6mr_for_each_table()
iwlwifi: move sysfs_create_group to post request firmware
iwlwifi: add name to Maintainers list
iwl3945: fix internal scan
iwl3945: enable stuck queue detection on 3945
ipv6: avoid high order allocations
ath5k: retain promiscuous setting
ath5k: depend on CONFIG_PM_SLEEP for suspend/resume functions
mac80211: process station blockack action frames from work
...
Linus Torvalds [Wed, 9 Jun 2010 19:43:04 +0000 (12:43 -0700)]
Merge branch 'for-2.6.35' of git://linux-nfs.org/~bfields/linux
* 'for-2.6.35' of git://linux-nfs.org/~bfields/linux:
nfsd4: shut down callback queue outside state lock
nfsd: nfsd_setattr needs to call commit_metadata
David Howells [Wed, 9 Jun 2010 18:52:22 +0000 (19:52 +0100)]
FRV: Reinstate null behaviour for the GDB remote protocol 'p' command
Reinstate the null behaviour that the in-kernel gdbstub had for the GDB
remote protocol 'p' command (retrieve a single register value) prior to
commit 7ca8b9c0dafd ("frv: extend gdbstub to support more features of
gdb").
Before that, the 'p' command just returned an empty reply, which causes
gdb to then go and use the 'g' command. However, since that commit, the
'p' command returns an error string, which causes gdb to abort its
connection to the target.
Not all gdb versions are affected, some use try 'g' first, and if that
works, don't bother with 'p', and so don't see the error.
Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Daniel Walker [Mon, 24 May 2010 17:15:00 +0000 (10:15 -0700)]
mmc: msm: fix compile error on MSM7x30
MSM7x30 isn't supported in this driver yet. If ones tried to compile it in
with MSM7x30 configure you get,
linux-2.6/drivers/mmc/host/msm_sdcc.c: In function 'msmsdcc_fifo_addr':
linux-2.6/drivers/mmc/host/msm_sdcc.c:165: error: 'MSM_SDC1_PHYS' undeclared (first use in this function)
linux-2.6/drivers/mmc/host/msm_sdcc.c:165: error: (Each undeclared identifier is reported only once
linux-2.6/drivers/mmc/host/msm_sdcc.c:165: error: for each function it appears in.)
linux-2.6/drivers/mmc/host/msm_sdcc.c:167: error: 'MSM_SDC2_PHYS' undeclared (first use in this function)
linux-2.6/drivers/mmc/host/msm_sdcc.c:169: error: 'MSM_SDC3_PHYS' undeclared (first use in this function)
linux-2.6/drivers/mmc/host/msm_sdcc.c:171: error: 'MSM_SDC4_PHYS' undeclared (first use in this function)
So we add a Kconfig check to prevent this.
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Alan Cox [Wed, 9 Jun 2010 08:39:49 +0000 (09:39 +0100)]
misc: Fix allocation 'borrowed' by vhost_net
10, 233 is allocated officially to /dev/kmview which is shipping in
Ubuntu and Debian distributions. vhost_net seem to have borrowed it
without making a proper request and this causes regressions in the other
distributions.
vhost_net can use a dynamic minor so use that instead. Also update the
file with a comment to try and avoid future misunderstandings.
cc: stable@kernel.org Signed-off-by: Alan Cox <device@lanana.org>
[ We should have caught this before 2.6.34 got released. - Linus ] Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jan Kiszka [Wed, 26 May 2010 19:36:33 +0000 (21:36 +0200)]
KVM: Fix order passed to iommu_unmap
This is obviously a left-over from the the old interface taking the
size. Apparently a mostly harmless issue with the current iommu_unmap
implementation.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com> Acked-by: Joerg Roedel <joerg.roedel@amd.com> Signed-off-by: Avi Kivity <avi@redhat.com>
Avi Kivity [Thu, 27 May 2010 11:35:58 +0000 (14:35 +0300)]
KVM: MMU: Remove user access when allowing kernel access to gpte.w=0 page
If cr0.wp=0, we have to allow the guest kernel access to a page with pte.w=0.
We do that by setting spte.w=1, since the host cr0.wp must remain set so the
host can write protect pages. Once we allow write access, we must remove
user access otherwise we mistakenly allow the user to write the page.
Reviewed-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com> Signed-off-by: Avi Kivity <avi@redhat.com>
Marcelo Tosatti [Fri, 28 May 2010 12:44:59 +0000 (09:44 -0300)]
KVM: MMU: invalidate and flush on spte small->large page size change
Always invalidate spte and flush TLBs when changing page size, to make
sure different sized translations for the same address are never cached
in a CPU's TLB.
Currently the only case where this occurs is when a non-leaf spte pointer is
overwritten by a leaf, large spte entry. This can happen after dirty
logging is disabled on a memslot, for example.
Noticed by Andrea.
KVM-Stable-Tag Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com> Signed-off-by: Avi Kivity <avi@redhat.com>
Joerg Roedel [Mon, 17 May 2010 12:43:35 +0000 (14:43 +0200)]
KVM: SVM: Implement workaround for Erratum 383
This patch implements a workaround for AMD erratum 383 into
KVM. Without this erratum fix it is possible for a guest to
kill the host machine. This patch implements the suggested
workaround for hypervisors which will be published by the
next revision guide update.
Joerg Roedel [Mon, 17 May 2010 12:43:34 +0000 (14:43 +0200)]
KVM: SVM: Handle MCEs early in the vmexit process
This patch moves handling of the MC vmexits to an earlier
point in the vmexit. The handle_exit function is too late
because the vcpu might alreadry have changed its physical
cpu.
Cc: stable@kernel.org Signed-off-by: Joerg Roedel <joerg.roedel@amd.com> Signed-off-by: Avi Kivity <avi@redhat.com>
Jean Delvare [Tue, 18 May 2010 07:34:12 +0000 (09:34 +0200)]
KVM: powerpc: fix init/exit annotation
kvmppc_e500_exit() is a module_exit function, so it should be tagged
with __exit, not __init. The incorrect annotation was added by commit 2986b8c72c272ea58edd37903b042c6da985627d.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Cc: stable@kernel.org Signed-off-by: Alexander Graf <agraf@suse.de> Signed-off-by: Avi Kivity <avi@redhat.com>
Michal Simek [Mon, 7 Jun 2010 13:17:55 +0000 (15:17 +0200)]
microblaze: Define ARCH_SLAB_MINALIGN to fix slab crash
The commit "mm: Move ARCH_SLAB_MINALIGN and
ARCH_KMALLOC_MINALIGN to <linux/slab_def.h>" 1f0ce8b3dd667dca7 which moved the ARCH_SLAB_MINALIGN
default into the global header broke FLAT for Microblaze.
Error message:
slab error in verify_redzone_free(): cache `idr_layer_cache':
memory outside object was overwritten
Linus Torvalds [Wed, 9 Jun 2010 03:52:19 +0000 (20:52 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
firewire: core: check for 1394a compliant IRM, fix inaccessibility of Sony camcorder
Linus Torvalds [Wed, 9 Jun 2010 03:16:28 +0000 (20:16 -0700)]
Revert "drm/i915: Don't enable pipe/plane/VCO early (wait for DPMS on)."
This reverts commit cfecde435dda78248d6fcdc424bed68d5db6be0b, since it
seems to cause some systems to not come up with any video output at all
(or video that only comes on when X starts up).
Fixes bugzilla:
http://bugzilla.kernel.org/show_bug.cgi?id=16163
Reported-and-tested-by: David John <davidjon@xenontk.org> Tested-by: Nick Bowler <nbowler@elliptictech.com> Acked-by: Carl Worth <cworth@cworth.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Wed, 9 Jun 2010 02:48:50 +0000 (19:48 -0700)]
Merge branch 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (23 commits)
drm/radeon: don't poll tv dac if crtc2 is in use.
drm/radeon: reset i2c valid to avoid incorrect tv-out polling.
drm/nv50: fix iommu errors caused by device reading from address 0
drm/nouveau: off by one in init_i2c_device_find()
nouveau: off by one in nv50_gpio_location()
drm/nouveau: completely fail init if we fail to map the PRAMIN BAR
drm/nouveau: match U/DP script against SOR link
drm/radeon/kms/pm: resurrect printing power states
drm/radeon/kms: add trivial debugging for voltage
drm/radeon/kms/r600+: use voltage from requested clock mode (v3)
drm/radeon/kms/pm: track current voltage (v2)
drm/radeon/kms/pm: Disable voltage adjust on RS780/RS880
drm/radeon/kms: fix typo in printing the HPD info
drm/radeon/kms/pm: add mid profile
drm/radeon/kms/pm: Misc fixes
drm/radeon/kms/combios: fix typo in voltage fix
drm/radeon/kms/evergreen: set accel_enabled
drm/vmwgfx: return -EFAULT for copy_to_user errors
drm/drm_crtc: return -EFAULT on copy_to_user errors
drm/fb: use printk to print out the switching to text mode error.
...
Linus Torvalds [Wed, 9 Jun 2010 01:13:24 +0000 (18:13 -0700)]
Merge branch 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6
* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6:
[S390] Update default configuration.
[S390] arch/s390/kvm: Use GFP_ATOMIC when a lock is held
[S390] kprobes: add parameter check to module_free()
[S390] appldata/extmem/kvm: add missing GFP_KERNEL flag
Dave Chinner [Wed, 9 Jun 2010 00:37:20 +0000 (10:37 +1000)]
writeback: limit write_cache_pages integrity scanning to current EOF
sync can currently take a really long time if a concurrent writer is
extending a file. The problem is that the dirty pages on the address
space grow in the same direction as write_cache_pages scans, so if
the writer keeps ahead of writeback, the writeback will not
terminate until the writer stops adding dirty pages.
For a data integrity sync, we only need to write the pages dirty at
the time we start the writeback, so we can stop scanning once we get
to the page that was at the end of the file at the time the scan
started.
This will prevent operations like copying a large file preventing
sync from completing as it will not write back pages that were
dirtied after the sync was started. This does not impact the
existing integrity guarantees, as any dirty page (old or new)
within the EOF range at the start of the scan will still be
captured.
This patch will not prevent sync from blocking on large writes into
holes. That requires more complex intervention while this patch only
addresses the common append-case of this sync holdoff.
Signed-off-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dave Chinner [Wed, 9 Jun 2010 00:37:19 +0000 (10:37 +1000)]
xfs: remove nr_to_write writeback windup.
Now that the background flush code has been fixed, we shouldn't need to
silently multiply the wbc->nr_to_write to get good writeback. Remove
that code.
Signed-off-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dave Chinner [Wed, 9 Jun 2010 00:37:18 +0000 (10:37 +1000)]
writeback: pay attention to wbc->nr_to_write in write_cache_pages
If a filesystem writes more than one page in ->writepage, write_cache_pages
fails to notice this and continues to attempt writeback when wbc->nr_to_write
has gone negative - this trace was captured from XFS:
This has adverse effects on filesystem writeback behaviour. write_cache_pages()
needs to terminate after a certain number of pages are written, not after a
certain number of calls to ->writepage are made. This is a regression
introduced by 17bc6c30cf6bfffd816bdc53682dd46fc34a2cf4 ("vfs: Add
no_nrwrite_index_update writeback control flag"), but cannot be reverted
directly due to subsequent bug fixes that have gone in on top of it.
Signed-off-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
J. Bruce Fields [Fri, 4 Jun 2010 20:42:08 +0000 (16:42 -0400)]
nfsd4: shut down callback queue outside state lock
This reportedly causes a lockdep warning on nfsd shutdown. That looks
like a false positive to me, but there's no reason why this needs the
state lock anyway.
Reported-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
projects / mv-sheeva.git / log