The 8020i protocol (also 8070i and QIC-157) uses 12-byte commands;
shorter commands must be padded. Simon Detheridge reports that his
3-TB USB disk drive claims to use the 8020i protocol (which is
normally meant for ATAPI devices like CD drives), and because of its
large size, the disk drive requires the use of 16-byte commands.
However the usb_stor_pad12_command() routine in usb-storage always
sets the command length to 12, making the drive impossible to use.
Since the SFF-8020i specification allows for 16-byte commands in
future extensions, we may as well accept them. This patch (as1490)
changes usb_stor_pad12_command() to leave commands larger than 12
bytes alone rather than truncating them.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Tested-by: Simon Detheridge <simon@widgit.com> CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ftdi_set_termios() is constantly setting the baud rate, data bits and parity
unnecessarily on every call, . When called while characters are being
transmitted can cause the FTDI chip to corrupt the serial port bit stream
output by stalling the output half a bit during the output of a character.
Simple fix by skipping this setting if the baud rate/data bits/parity are
unchanged.
Signed-off-by: Andrew Worsley <amworsley@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I get report from customer that his usb-serial
converter doesn't work well,it sometimes work,
but sometimes it doesn't.
The usb-serial converter's id:
vendor_id product_id
0x4348 0x5523
Then I search the usb-serial codes, and there are
two drivers announce support this device, pl2303
and ch341, commit 026dfaf1 cause it. Through many
times to test, ch341 works well with this device,
and pl2303 doesn't work quite often(it just work quite little).
ch341 works well with this device, so we doesn't
need pl2303 to support.I try to revert 026dfaf1 first,
but it failed. So I prepare this patch by hand to revert it.
Signed-off-by: Wang YanQing <Udknight@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Starting with 4.4, gcc will happily accept -Wno-<anything> in the
cc-option test and complain later when compiling a file that has some
other warning. This rather unexpected behavior is intentional as per
http://gcc.gnu.org/PR28322, so work around it by testing for support of
the opposite option (without the no-). Introduce a new Makefile function
cc-disable-warning that does this and update two uses of cc-option in
the toplevel Makefile.
Reported-and-tested-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Michal Marek <mmarek@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
At this point, skb->data points to skb_transport_header.
So, headroom check is wrong.
For some case:bridge(UFO is on) + eth device(UFO is off),
there is no enough headroom for IPv6 frag head.
But headroom check is always false.
This will bring about data be moved to there prior to skb->head,
when adding IPv6 frag header to skb.
Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com> Acked-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The /proc/vmallocinfo shows information about vmalloc allocations in vmlist
that is a linklist of vm_struct. It, however, may access pages field of
vm_struct where a page was not allocated. This results in a null pointer
access and leads to a kernel panic.
Why this happen:
In __vmalloc_node() called from vmalloc(), newly allocated vm_struct
is added to vmlist at __get_vm_area_node() and then, some fields of
vm_struct such as nr_pages and pages are set at __vmalloc_area_node(). In
other words, it is added to vmlist before it is fully initialized. At the
same time, when the /proc/vmallocinfo is read, it accesses the pages field
of vm_struct according to the nr_pages field at show_numa_info(). Thus, a
null pointer access happens.
Patch:
This patch adds newly allocated vm_struct to the vmlist *after* it is fully
initialized. So, it can avoid accessing the pages field with unallocated
page when show_numa_info() is called.
Signed-off-by: Mitsuo Hayasaka <mitsuo.hayasaka.hu@hitachi.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: David Rientjes <rientjes@google.com> Cc: Namhyung Kim <namhyung@gmail.com> Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com> Cc: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds a mechanism to resume selected IRQs during syscore_resume
instead of dpm_resume_noirq.
Under Xen we need to resume IRQs associated with IPIs early enough
that the resched IPI is unmasked and we can therefore schedule
ourselves out of the stop_machine where the suspend/resume takes
place.
This issue was introduced by 676dc3cf5bc3 "xen: Use IRQF_FORCE_RESUME".
Back ported to 2.6.32 (which lacks syscore support) by calling the relavant
resume function directly from sysdev_resume).
v2: Fixed non-x86 build errors.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com> Cc: Rafael J. Wysocki <rjw@sisk.pl> Cc: Jeremy Fitzhardinge <Jeremy.Fitzhardinge@citrix.com> Cc: xen-devel <xen-devel@lists.xensource.com> Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Link: http://lkml.kernel.org/r/1318713254.11016.52.camel@dagon.hellion.org.uk Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Move the access control up from the fast paths, which are no longer
universally taken first, up into the caller. This then duplicates some
sanity checking along the slow paths, but is much simpler.
Tracked as CVE-2010-2962.
Reported-by: Kees Cook <kees@ubuntu.com> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It was wrong included in 2.6.32 stable (was intended for 2.6.38+ in the
original commit changelog in Linus tree), and causes a regression on
2.6.32 (https://launchpad.net/bugs/875300).
Signed-off-by: Herton Ronaldo Krzesinski <herton.krzesinski@canonical.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This example file uses the old V4L1 API. It also doesn't use libv4l.
So, it is completely obsolete. A good example already exists at
v4l-utils (v4l2grab.c):
http://git.linuxtv.org/v4l-utils.git
When the number of failed devices exceeds the allowed number
we must abort any active parity operations (checks or updates) as they
are no longer meaningful, and can lead to a BUG_ON in
handle_parity_checks6.
Reported-by: Chris Paulson-Ellis <chris@edesix.com> Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Disable the new -Wunused-but-set-variable that was added in gcc 4.6.0
It produces more false positives than useful warnings.
This can still be enabled using W=1
[gregkh - No it can not for 2.6.32, but we don't care]
Signed-off-by: Dave Jones <davej@redhat.com> Acked-by: Sam Ravnborg <sam@ravnborg.org> Tested-by: Sam Ravnborg <sam@ravnborg.org> Signed-off-by: Michal Marek <mmarek@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In enter_state() we use "state" as an offset for the pm_states[]
array. The pm_states[] array only has PM_SUSPEND_MAX elements so
this test is off by one.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On writes in MODE_RAW the mtd_oob_ops struct is not sufficiently
initialized which may cause nandwrite to fail. With this patch
it is possible to write raw nand/oob data without additional ECC
(either for testing or when some sectors need different oob layout
e.g. bootloader) like
nandwrite -n -r -o /dev/mtd0 <myfile>
L2TP for example uses NLA_MSECS like this:
policy:
[L2TP_ATTR_RECV_TIMEOUT] = { .type = NLA_MSECS, },
code:
if (info->attrs[L2TP_ATTR_RECV_TIMEOUT])
cfg.reorder_timeout = nla_get_msecs(info->attrs[L2TP_ATTR_RECV_TIMEOUT]);
As nla_get_msecs() is essentially nla_get_u64() plus the
conversion to a HZ-based value, this will not properly
reject attributes from userspace that aren't long enough
and might overrun the message.
Add NLA_MSECS to the attribute minlen array to check the
size properly.
Cc: Thomas Graf <tgraf@suug.ch> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The sunrpc layer keeps a cache of recently used credentials and
'unx_match' is used to find the credential which matches the current
process.
However unx_match allows a match when the cached credential has extra
groups at the end of uc_gids list which are not in the process group list.
So if a process with a list of (say) 4 group accesses a file and gains
access because of the last group in the list, then another process
with the same uid and gid, and a gid list being the first tree of the
gids of the original process tries to access the file, it will be
granted access even though it shouldn't as the wrong rpc credential
will be used.
Make sure that SCSI device removal via scsi_remove_host() does finish
all pending SCSI commands. Currently that's not the case and hence
removal of a SCSI host during I/O can cause a deadlock. See also
"blkdev_issue_discard() hangs forever if underlying storage device is
removed" (http://bugzilla.kernel.org/show_bug.cgi?id=40472). See also
http://lkml.org/lkml/2011/8/27/6.
Signed-off-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: James Bottomley <JBottomley@Parallels.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The call to complete() in st_scsi_execute_end() wakes up sleeping thread
in write_behind_check(), which frees the st_request, thus invalidating
the pointer to the associated bio structure, which is then passed to the
blk_rq_unmap_user(). Fix by storing pointer to bio structure into
temporary local variable.
This bug is present since at least linux-2.6.32.
Signed-off-by: Petr Uzel <petr.uzel@suse.cz> Reported-by: Juergen Groß <juergen.gross@ts.fujitsu.com> Reviewed-by: Jan Kara <jack@suse.cz> Acked-by: Kai Mäkisara <kai.makisara@kolumbus.fi> Signed-off-by: James Bottomley <JBottomley@Parallels.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
arch/powerpc/sysdev/mpic.c: In function 'irq_choose_cpu':
arch/powerpc/sysdev/mpic.c:574: error: passing argument 1 of '__cpus_equal' from incompatible pointer type
Reported-by: Jiri Slaby <jslaby@suse.cz> Cc: Jiajun Wu <b06378@freescale.com> Cc: Li Yang <leoli@freescale.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It breaks the build and probably shouldn't be in the 2.6.32 kernel
Reported-by: Stefan Bader <stefan.bader@canonical.com> Cc: Chris Paulson-Ellis <chris@edesix.com> Cc: Axel Lin <axel.lin@gmail.com> Cc: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This doesn't make much sense, and it exposes a bug in the kernel where
attempts to create a new file in an append-only directory using
O_CREAT will fail (but still leave a zero-length file). This was
discovered when xfstests #79 was generalized so it could run on all
file systems.
The reason is that it forgot to mark dirty when splitting two extents in
ext4_ext_convert_to_initialized(). Althrough ex has been updated in
memory, it is not dirtied both in ext4_ext_convert_to_initialized() and
ext4_ext_insert_extent(). The disk layout is corrupted. Then it will
meet with a BUG_ON() when writting at the start of that extent again.
Cc: "Theodore Ts'o" <tytso@mit.edu> Cc: Xiaoyun Mao <xiaoyun.maoxy@aliyun-inc.com> Cc: Yingbin Wang <yingbin.wangyb@aliyun-inc.com> Cc: Jia Wan <jia.wanj@aliyun-inc.com> Signed-off-by: Zheng Liu <wenqing.lz@taobao.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
tc_fill_qdisc() should not be called for builtin qdisc, or it
dereference a NULL pointer to get device ifindex.
Fix is to always use tc_qdisc_dump_ignore() before calling
tc_fill_qdisc().
Reported-by: Ben Pfaff <blp@nicira.com> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When one of the SSID's length passed in a scan or sched_scan request
is larger than 255, there will be an overflow in the u8 that is used
to store the length before checking. This causes the check to fail
and we overrun the buffer when copying the SSID.
Fix this by checking the nl80211 attribute length before copying it to
the struct.
A remote user can provide a small value for the command size field in
the command header of an l2cap configuration request, resulting in an
integer underflow when subtracting the size of the configuration request
header. This results in copying a very large amount of data via
memcpy() and destroying the kernel heap. Check for underflow.
Signed-off-by: Dan Rosenberg <drosenberg@vsecurity.com> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit a626ca6a6564 ("vm: fix vm_pgoff wrap in stack expansion") fixed
the case of an expanding mapping causing vm_pgoff wrapping when you had
downward stack expansion. But there was another case where IA64 and
PA-RISC expand mappings: upward expansion.
Commit 982134ba6261 ("mm: avoid wrapping vm_pgoff in mremap()") fixed
the case of a expanding mapping causing vm_pgoff wrapping when you used
mremap. But there was another case where we expand mappings hiding in
plain sight: the automatic stack expansion.
This fixes that case too.
This one also found by Robert Święcki, using his nasty system call
fuzzer tool. Good job.
If the NLM daemon is killed on the NFS server, we can currently end up
hanging forever on an 'unlock' request, instead of aborting. Basically,
if the rpcbind request fails, or the server keeps returning garbage, we
really want to quit instead of retrying.
All of those are rw-r--r-- and all are broken for suid - if you open
a file before the target does suid-root exec, you'll be still able
to access it. For personality it's not a big deal, but for syscall
and stack it's a real problem.
Fix: check that task is tracable for you at the time of read().
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Lower SCM_MAX_FD from 255 to 253 so that allocations for scm_fp_list are
halved. (commit f8d570a4 added two pointers in this structure)
scm_fp_dup() should not copy whole structure (and trigger kmemcheck
warnings), but only the used part. While we are at it, only allocate
needed size.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The newer Lenovo ThinkPads have HKEY HID of LEN0068 instead
of IBM0068. Added new HID so that thinkpad_acpi module will
auto load on these newer Lenovo ThinkPads.
Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br> Cc: stable@vger.kernel.org Signed-off-by: Manoj Iyer <manoj.iyer@canonical.com> Signed-off-by: Andy Lutomirski <luto@mit.edu> Signed-off-by: Matthew Garrett <mjg@redhat.com> Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Florian Fainelli [Mon, 17 Oct 2011 17:47:44 +0000 (19:47 +0200)]
watchdog: mtx1-wdt: fix build failure
Commit 6d86a0ee (watchdog: mtx1-wdt: request gpio before using it) was
backported from upstream. The patch is using a gpiolib call which is only
available in kernel 2.6.34+. Fix build by using the "old" gpiolib API
instead.
This adds a mechanism to resume selected IRQs during syscore_resume
instead of dpm_resume_noirq.
Under Xen we need to resume IRQs associated with IPIs early enough
that the resched IPI is unmasked and we can therefore schedule
ourselves out of the stop_machine where the suspend/resume takes
place.
This issue was introduced by 676dc3cf5bc3 "xen: Use IRQF_FORCE_RESUME".
Back ported to 2.6.32 (which lacks syscore support) by calling the relavant
resume function directly from sysdev_resume).
Signed-off-by: Ian Campbell <ian.campbell@citrix.com> Cc: Rafael J. Wysocki <rjw@sisk.pl> Cc: Jeremy Fitzhardinge <Jeremy.Fitzhardinge@citrix.com> Cc: xen-devel <xen-devel@lists.xensource.com> Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Link: http://lkml.kernel.org/r/1318713254.11016.52.camel@dagon.hellion.org.uk Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
vcpu->last_guest_tsc is updated in vcpu_enter_guest() and kvm_arch_vcpu_put()
by getting the last value of the TSC from the guest.
On reset, the SeaBIOS resets the TSC to 0, which triggers a bug on the next
call to kvm_write_guest_time(): Since vcpu->hw_clock.tsc_timestamp still
contains the old value before the reset, "max_kernel_ns = vcpu->last_guest_tsc
- vcpu->hw_clock.tsc_timestamp" gets negative. Since the variable is u64, it
gets translated to a large positive value.
For completeness, here are the values for my 3 GHz CPU:
vcpu->hv_clock.tsc_shift =-1
vcpu->hv_clock.tsc_to_system_mul =2_863_019_502
This makes the guest kernel crawl very slowly when clocksource=kvmclock is
used: sleeps take way longer than expected and don't match wall clock any more.
The times printed with printk() don't match real time and the reboot often
stalls for long times.
In linux-git this isn't a problem, since on every MSR_IA32_TSC write
vcpu->arch.hv_clock.tsc_timestamp is reset to 0, which disables above logic.
The code there is only in arch/x86/kvm/x86.c, since much of the kvm-clock
related code has been refactured for 2.6.37: 99e3e30a arch/x86/kvm/x86.c
(Zachary Amsden 2010-08-19 22:07:17 -1000 1084)
vcpu->arch.hv_clock.tsc_timestamp = 0;
A user reported a kernel bug when running a particular program that did
the following:
created 32 threads
- each thread took a mutex, grabbed a global offset, added a buffer size
to that offset, released the lock
- read from the given offset in the file
- created a new thread to do the same
- exited
The result is that cfq's close cooperator logic would trigger, as the
threads were issuing I/O within the mean seek distance of one another.
This workload managed to routinely trigger a use after free bug when
walking the list of merge candidates for a particular cfqq
(cfqq->new_cfqq). The logic used for merging queues looks like this:
/* Avoid a circular list and skip interim queue merges */
while ((__cfqq = new_cfqq->new_cfqq)) {
if (__cfqq == cfqq)
return;
new_cfqq = __cfqq;
}
process_refs = cfqq_process_refs(cfqq);
/*
* If the process for the cfqq has gone away, there is no
* sense in merging the queues.
*/
if (process_refs == 0)
return;
/*
* Merge in the direction of the lesser amount of work.
*/
new_process_refs = cfqq_process_refs(new_cfqq);
if (new_process_refs >= process_refs) {
cfqq->new_cfqq = new_cfqq;
atomic_add(process_refs, &new_cfqq->ref);
} else {
new_cfqq->new_cfqq = cfqq;
atomic_add(new_process_refs, &cfqq->ref);
}
}
When a merge candidate is found, we add the process references for the
queue with less references to the queue with more. The actual merging
of queues happens when a new request is issued for a given cfqq. In the
case of the test program, it only does a single pread call to read in
1MB, so the actual merge never happens.
Normally, this is fine, as when the queue exits, we simply drop the
references we took on the other cfqqs in the merge chain:
/*
* If this queue was scheduled to merge with another queue, be
* sure to drop the reference taken on that queue (and others in
* the merge chain). See cfq_setup_merge and cfq_merge_cfqqs.
*/
__cfqq = cfqq->new_cfqq;
while (__cfqq) {
if (__cfqq == cfqq) {
WARN(1, "cfqq->new_cfqq loop detected\n");
break;
}
next = __cfqq->new_cfqq;
cfq_put_queue(__cfqq);
__cfqq = next;
}
However, there is a hole in this logic. Consider the following (and
keep in mind that each I/O keeps a reference to the cfqq):
q1->new_cfqq = q2 // q2 now has 2 process references
q3->new_cfqq = q2 // q2 now has 3 process references
// the process associated with q2 exits
// q2 now has 2 process references
// queue 1 exits, drops its reference on q2
// q2 now has 1 process reference
// q3 exits, so has 0 process references, and hence drops its references
// to q2, which leaves q2 also with 0 process references
q4 comes along and wants to merge with q3
q3->new_cfqq still points at q2! We follow that link and end up at an
already freed cfqq.
So, the fix is to not follow a merge chain if the top-most queue does
not have a process reference, otherwise any queue in the chain could be
already freed. I also changed the logic to disallow merging with a
queue that does not have any process references. Previously, we did
this check for one of the merge candidates, but not the other. That
doesn't really make sense.
Without the attached patch, my system would BUG within a couple of
seconds of running the reproducer program. With the patch applied, my
system ran the program for over an hour without issues.
This addresses the following bugzilla:
https://bugzilla.kernel.org/show_bug.cgi?id=16217
Thanks a ton to Phil Carns for providing the bug report and an excellent
reproducer.
[ Note for stable: this applies to 2.6.32/33/34 ].
Signed-off-by: Jeff Moyer <jmoyer@redhat.com> Reported-by: Phil Carns <carns@mcs.anl.gov> Signed-off-by: Jens Axboe <jaxboe@fusionio.com> Signed-off-by: Suresh Jayaraman <sjayaraman@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
cfq_queues are merged if they are issuing requests within the mean seek
distance of one another. This patch detects when the coopearting stops and
breaks the queues back up.
The flag used to indicate that a cfqq was allowed to jump ahead in the
scheduling order due to submitting a request close to the queue that
just executed. Since closely cooperating queues are now merged, the flag
holds little meaning. Change it to indicate that multiple queues were
merged. This will later be used to allow the breaking up of merged queues
when they are no longer cooperating.
When cooperating cfq_queues are detected currently, they are allowed to
skip ahead in the scheduling order. It is much more efficient to
automatically share the cfq_queue data structure between cooperating processes.
Performance of the read-test2 benchmark (which is written to emulate the
dump(8) utility) went from 12MB/s to 90MB/s on my SATA disk. NFS servers
with multiple nfsd threads also saw performance increases.
async cfq_queue's are already shared between processes within the same
priority, and forthcoming patches will change the mapping of cic to sync
cfq_queue from 1:1 to 1:N. So, calculate the seekiness of a process
based on the cfq_queue instead of the cfq_io_context.
ubd_file_size() cannot use ubd_dev->cow.file because at this time
ubd_dev->cow.file is not initialized.
Therefore, ubd_file_size() will always report a wrong disk size when
COW files are used.
Reading from /dev/ubd* would crash the kernel.
We have to read the correct disk size from the COW file's backing
file.
Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
To configure pads during the initialisation a set of special constants
is used, e.g.
#define MX25_PAD_FEC_MDIO__FEC_MDIO IOMUX_PAD(0x3c4, 0x1cc, 0x10, 0, 0, PAD_CTL_HYS | PAD_CTL_PUS_22K_UP)
The problem is that no pull-up/down is getting activated unless both
PAD_CTL_PUE (pull-up enable) and PAD_CTL_PKE (pull/keeper module
enable) set. This is clearly stated in the i.MX25 datasheet and is
confirmed by the measurements on hardware. This leads to some rather
hard to understand bugs such as misdetecting an absent ethernet PHY (a
real bug i had), unstable data transfer etc. This might affect mx25,
mx35, mx50, mx51 and mx53 SoCs.
It's reasonable to expect that if the pullup value is specified, the
intention was to have it actually active, so we implicitly add the
needed bits.
This device is not using the proper demod IF. Instead of using the
IF macro, it is specifying a IF frequency. This doesn't work, as xc3028
needs to load an specific SCODE for the tuner. In this case, there's
no IF table for 5 MHz.
If the bus has been reset on resume, set the alternate setting to 0.
This should be the default value, but some devices crash or otherwise
misbehave if they don't receive a SET_INTERFACE request before any other
video control request.
Microdia's 0c45:6437 camera has been found to require this change or it
will stop sending video data after resume.
uvc_video.c]
Signed-off-by: Ming Lei <ming.lei@canonical.com> Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Jean Delvare <jdelvare@suse.de> Cc: Paul Mundt <lethal@linux-sh.org> Cc: Sebastian Siewior <bigeasy@linutronix.de> Signed-off-by: Paul Mundt <lethal@linux-sh.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Put sysfs attributes of ccwgroup devices in an attribute group to
ensure that these attributes are actually present when userspace
is notified via uevents.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ak4535_reg should be 8bit, but cache table is defined as 16bit.
Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Reported-by: Chris Paulson-Ellis <chris@edesix.com> Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fan Yong <yong.fan@whamcloud.com> noticed setting
FMODE_32bithash wouldn't work with nfsd v4, as
nfsd4_readdir() checks for 32 bit cookies. However, according to RFC 3530
cookies have a 64 bit type and cookies are also defined as u64 in
'struct nfsd4_readdir'. So remove the test for >32-bit values.
Signed-off-by: Bernd Schubert <bernd.schubert@itwm.fraunhofer.de> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The parameter's origin type is long. On an i386 architecture, it can
easily be larger than 0x80000000, causing this function to convert it
to a sign-extended u64 type.
Change the type to unsigned long so we get the correct result.
Signed-off-by: hank <pyu@redhat.com> Cc: John Stultz <john.stultz@linaro.org>
[ build fix ] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Due to post-increment in condition of kmod_loop_msg in __request_module(),
the system log can be spammed by much more than 5 instances of the 'runaway
loop' message if the number of events triggering it makes the kmod_loop_msg
to overflow.
Fix that by making sure we never increment it past the threshold.
The stable@kernel.org email address has been replaced with the
stable@vger.kernel.org mailing list. Change the stable kernel rules to
reference the new list instead of the semi-defunct email alias.
Some Stellaris evaluation kits have the JTAG/SWD FTDI chip onboard,
and some, like EK-LM3S9B90, come with a separate In-Circuit Debugger
Interface Board. The ICDI board can also be used stand-alone, for
other boards and chips than the kit it came with. The ICDI has both
old style 20-pin JTAG connector and new style JTAG/SWD 10-pin 1.27mm
pitch connector.
Tested with EK-LM3S9B90, where the BD-ICDI board is included.
Signed-off-by: Peter Stuge <peter@stuge.se> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add vendor and product ID for the SMART USB to serial adapter. These
were meant to be used with their SMART Board whiteboards, but can be
re-purposed for other tasks. Tested and working (at at least 9600 bps).
Signed-off-by: Eric Benoit <eric@ecks.ca> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The new runtime PM code has shown that many webcams suffer
from a race condition that may crash them upon resume.
Runtime PM is especially prone to show the problem because
it retains power to the cameras at all times. However
system suspension may also crash the devices and retain
power to the devices.
The only way to solve this problem without races is in
usbcore with the RESET_RESUME quirk.
Signed-off-by: Oliver Neukum <oneukum@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern points out that after spin_unlock(&ps->lock) there is no
guarantee that ps->pid won't be freed. Since kill_pid_info_as_uid() is
called after the spin_unlock(), the pid passed to it must be pinned.
This patch solves two things:
1) Enables autosense emulation code to correctly
interpret descriptor format sense data, and
2) Fixes a bug whereby the autosense emulation
code would overwrite descriptor format sense data
with SENSE KEY HARDWARE ERROR in fixed format, to
incorrectly look like this:
Oct 21 14:11:07 localhost kernel: sd 7:0:0:0: [sdc] Sense Key : Recovered Error [current] [descriptor]
Oct 21 14:11:07 localhost kernel: Descriptor sense data with sense descriptors (in hex):
Oct 21 14:11:07 localhost kernel: 72 01 04 1d 00 00 00 0e 09 0c 00 00 00 00 00 00
Oct 21 14:11:07 localhost kernel: 00 4f 00 c2 00 50
Oct 21 14:11:07 localhost kernel: sd 7:0:0:0: [sdc] ASC=0x4 ASCQ=0x1d
Signed-off-by: Luben Tuikov <ltuikov@yahoo.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Acked-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
epoll can acquire recursively acquire ep->mtx on multiple "struct
eventpoll"s at once in the case where one epoll fd is monitoring another
epoll fd. This is perfectly OK, since we're careful about the lock
ordering, but it causes spurious lockdep warnings. Annotate the recursion
using mutex_lock_nested, and add a comment explaining the nesting rules
for good measure.
Recent versions of systemd are triggering this, and it can also be
demonstrated with the following trivial test program:
--------------------8<--------------------
int main(void) {
int e1, e2;
struct epoll_event evt = {
.events = EPOLLIN
};
When compiling an i386_defconfig kernel with gcc-4.6.1-9.fc15.i686, I
noticed a warning about the asm operand for test_bit in kprobes'
can_boost. I discovered that this caused only the first long of
twobyte_is_boostable[] to be output.
Jakub filed and fixed gcc PR50571 to correct the warning and this output
issue. But to solve it for less current gcc, we can make kprobes'
twobyte_is_boostable[] non-const, and it won't be optimized out.
Before:
CC arch/x86/kernel/kprobes.o
In file included from include/linux/bitops.h:22:0,
from include/linux/kernel.h:17,
from [...]/arch/x86/include/asm/percpu.h:44,
from [...]/arch/x86/include/asm/current.h:5,
from [...]/arch/x86/include/asm/processor.h:15,
from [...]/arch/x86/include/asm/atomic.h:6,
from include/linux/atomic.h:4,
from include/linux/mutex.h:18,
from include/linux/notifier.h:13,
from include/linux/kprobes.h:34,
from arch/x86/kernel/kprobes.c:43:
[...]/arch/x86/include/asm/bitops.h: In function ‘can_boost.part.1’:
[...]/arch/x86/include/asm/bitops.h:319:2: warning: use of memory input
without lvalue in asm operand 1 is deprecated [enabled by default]
During kdump testing I noticed timeouts when initialising each IPR
adapter. While the driver has logic to detect an adapter in an
indeterminate state, it wasn't triggering and each adapter went
through a 5 minute timeout before finally going operational.
Some analysis showed the needs_hard_reset flag wasn't getting set.
We can check the reset_devices kernel parameter which is set by
kdump and force a full reset. This fixes the problem.
Signed-off-by: Anton Blanchard <anton@samba.org> Acked-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There are 2 situations wherein the xhci_ring* might not get freed:
- When xhci_ring_alloc() -> xhci_segment_alloc() returns NULL and
we goto the fail: label in xhci_ring_alloc. In this case, the ring
will not get kfreed.
- When the num_segs argument to xhci_ring_alloc is passed as 0 and
we try to free the rung after that.
( This doesn't really happen as of now in the code but we seem to
be entertaining num_segs=0 in xhci_ring_alloc )
This should be backported to kernels as old as 2.6.31.
Signed-off-by: Kautuk Consul <consul.kautuk@gmail.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If the usermode app does an ioctl over this serial device by
using TIOCMIWAIT, then the code will wait by setting the current
task state to TASK_INTERRUPTIBLE and then calling schedule().
This will be woken up by the qt2_process_modem_status on URB
completion when the port_extra->shadowMSR is set to the new
modem status.
However, this could result in a lost wakeup scenario due to a race
in the logic in the qt2_ioctl(TIOCMIWAIT) loop and the URB completion
for new modem status in qt2_process_modem_status.
Due to this, the usermode app's task will continue to sleep despite a
change in the modem status.
Signed-off-by: Kautuk Consul <consul.kautuk@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
x25_find_listener does not check that the amount of call user data given
in the skb is big enough in per-socket comparisons, hence buffer
overreads may occur. Fix this by adding a check.
Signed-off-by: Matthew Daley <mattjd@gmail.com> Cc: Eric Dumazet <eric.dumazet@gmail.com> Cc: Andrew Hendry <andrew.hendry@gmail.com> Acked-by: Andrew Hendry <andrew.hendry@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The w83627ehf driver is improperly reporting thermal diode sensors as
type 2, instead of 3. This caused "sensors" and possibly other
monitoring tools to report these sensors as "transistor" instead of
"thermal diode".
Furthermore, diode subtype selection (CPU vs. external) is only
supported by the original W83627EHF/EHG. All later models only support
CPU diode type, and some (NCT6776F) don't even have the register in
question so we should avoid reading from it.
Patch to add SiGma Micro-based keyboards (1c4f:0002) to hid-quirks.
These keyboards dont seem to allow the records to be initialized, and hence a
timeout occurs when the usbhid driver attempts to initialize them. The patch
just adds the signature for these keyboards to the hid-quirks list with the
setting HID_QUIRK_NO_INIT_REPORTS. This removes the 5-10 second wait for the
timeout to occur.
Like e65cc194f7628ecaa02462f22f42fb09b50dcd49 this patch enables 64bit DMA
for the AHCI SATA controller of a board that has the SB600 southbridge. In
this case though we're enabling 64bit DMA for the Asus M3A motherboard. It
is a new enough board that all of the BIOS releases since the initial
release (0301 from 2007-10-22) work correctly with 64bit DMA enabled.
Signed-off-by: Mark Nelson <mdnelson8@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@pobox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The following patch is admittedly a band-aid, and does not solve the
root cause, but it still is a good candidate for hardening as a pointer
check before reference.
Signed-off-by: Mark Salyzyn <mark_salyzyn@us.xyratex.com> Tested-by: Jack Wang <jack_wang@usish.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Incorrect variable was used in validating the akm_suites array from
NL80211_ATTR_AKM_SUITES. In addition, there was no explicit
validation of the array length (we only have room for
NL80211_MAX_NR_AKM_SUITES).
This can result in a buffer write overflow for stack variables with
arbitrary data from user space. The nl80211 commands using the affected
functionality require GENL_ADMIN_PERM, so this is only exposed to admin
users.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In an enclosure model where there are chaining expanders to a large body
of storage, it was discovered that libsas, responding to a broadcast
event change, would only revalidate the domain of first child expander
in the list.
The issue is that the pointer value to the discovered source device was
used to break out of the loop, rather than the content of the pointer.
This still remains non-compliant as the revalidate domain code is
supposed to loop through all child expanders, and not stop at the first
one it finds that reports a change count. However, the design of this
routine does not allow multiple device discoveries and that would be a
more complicated set of patches reserved for another day. We are fixing
the glaring bug rather than refactoring the code.
Signed-off-by: Mark Salyzyn <msalyzyn@us.xyratex.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Following reports on the list, it looks like the 3e-9xxx driver will leak dma
mappings every time we get a transient queueing error back from the card.
This is because it maps the sg list in the routine that sends the command, but
doesn't unmap again in the transient failure path (even though the command is
sent back to the block layer). Fix by unmapping before returning the status.
Reported-by: Chris Boot <bootc@bootc.net> Tested-by: Chris Boot <bootc@bootc.net> Acked-by: Adam Radford <aradford@gmail.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When the headphone pin is assigned as primary output to line_out_pins[],
the automatic HP-pin assignment by ASSID must be suppressed. Otherwise
a wrong pin might be assigned to the headphone and breaks the auto-mute.
projects / karo-tx-linux.git / log