Rabeeh Khoury [Sat, 23 Aug 2014 09:11:47 +0000 (10:11 +0100)]
ARM: dts: hummingboard: gpio-ir on gpio 3,5
HummingBoard after rev 2.0 and the production one starting rev 3.0 uses
gpio 3,5 (EIM_DA5 pad) as the gpio infra red receiver input.
Since the original Carrier1 board is obsolete and we are retiring it,
update the DT file for this. This will mean IR reception will not
work on Carrier1 with this DT file.
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Stefan Agner [Mon, 18 Aug 2014 20:07:17 +0000 (22:07 +0200)]
ARM: dts: vf610-twr: Add USB support
Add USB support for Freescale Vybrid tower. The USB hosts over-current
protection signal is not connected to the PHY's over- current
protection, hence we need to disable it.
Signed-off-by: Stefan Agner <stefan@agner.ch> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Stefan Agner [Mon, 18 Aug 2014 20:07:16 +0000 (22:07 +0200)]
ARM: dts: vf610-colibri: Add USB support
Add USB support for Colibri VF61 modules. The Colibri standard pinout
defines a pin for USB over-current. However, due to lack of pinmux
options, the USB hosts over-current protection signal of the Colibri
standard could not be connected to the PHY's over-current protection.
Hence we need to disable the over-current functionality of the USB
controller.
Signed-off-by: Stefan Agner <stefan@agner.ch> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Stefan Agner [Mon, 18 Aug 2014 20:07:14 +0000 (22:07 +0200)]
ARM: dts: vf610: Add usbmisc for non-core registers
Add device tree node for usbmisc which controls the non-core USB
registers. This is required to use the property to disable the over-
current detection.
Signed-off-by: Stefan Agner <stefan@agner.ch> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Stefan Agner [Mon, 18 Aug 2014 20:07:11 +0000 (22:07 +0200)]
ARM: dts: vf610: Add USB PHY and controller
This adds USB PHY and USB controller nodes. Vybrid SoCs have two
independent USB cores which each supports DR (dual role). However,
real OTG is not supported since the OTG ID pin is not available.
The PHYs are located within the anadig register range, hence we need
to change the length of the anadig registers.
Signed-off-by: Stefan Agner <stefan@agner.ch> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
[ukl: rebase from ancient kernel version] Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Lucas Stach [Wed, 23 Jul 2014 17:29:11 +0000 (19:29 +0200)]
ARM: dts: imx6qdl-sabresd: add always on pcie regulator
Everything in the PCI specification assumes devices to be
enumerable on startup. This is only possible if they have
power available.
A future improvement may allow this regulator to be switched
off for D3hot and D3cold power states, but there is a lot
of work to do the pcie host controller side for this to work.
To keep things simple always enable the regulator for now.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Stefan Agner [Fri, 18 Jul 2014 14:25:18 +0000 (16:25 +0200)]
ARM: dts: vf610-colibri: split device tree for carrier boards
The Colibri VF61 is a module which needs a carrier board to actually
run. Different carrier board have different hardware support, hence
we should reflect this in the device tree files. This patch adds the
Colibri Evaluation Board, which supports almost all peripherals
defined in the Colibri standard.
Also align the compatible naming, file splitting and file naming with
the scheme which was choosen for the Tegra based modules.
Signed-off-by: Stefan Agner <stefan@agner.ch> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
The imx weim driver is used by some mx27/mx1 boards, so let's enable it by
default.
Generated this patch by doing:
- make imx_v4_v5_defconfig
- make menuconfig and manually select CONFIG_IMX_WEIM
- make savedefconfig
- cp defconfig arch/arm/configs/imx_v4_v5_defconfig
ARM: imx: source gpt per clk from OSC for system timer
On i.MX6Q TO > 1.0, i.MX6DL and i.MX6SX, gpt per clock
can be from OSC instead of ipg_per, as ipg_per's rate
may be scaled when system enter low bus mode, to keep
system timer NOT drift, better to make gpt per clock
at fixed rate, here add support for gpt per clock to
be from OSC which is at fixed rate always.
There are some difference on this implementation of
gpt per clock source, see below for details:
i.MX6Q TO > 1.0: GPT_CR_CLKSRC, b'101 selects fix clock
of OSC / 8 for gpt per clk;
i.MX6DL and i.MX6SX: GPT_CR_CLKSRC, b'101 selects OSC
for gpt per clk, and we must enable GPT_CR_24MEM to
enable OSC clk source for gpt per, GPT_PR_PRESCALER24M
is for pre-scaling of this OSC clk, here set it to 8
to make gpt per clk is 3MHz;
i.MX6SL: ipg_per can be from OSC directly, so no need to
implement this new clk source for gpt per.
Add gpt_3m clock for i.mx6qdl, as gpt can source clock
from OSC, some i.MX6 series SOCs has fixed divider of
8 for gpt clock, so here add a fix clk of gpt_3m.
i.MX6Q TO1.0 has no gpt_3m option, so force it to be
from ipg_per.
ARM: imx: fix register offset of pll7_usb_host gate clock
There is a copy&paste error on register offset of pll7_usb_host gate
clock introduced by i.MX6 PLL bypass support patches. The error breaks
the ENET function, because it overwrites the pll6_enet gate bit.
Correct the offset for all i.MX6 clock drivers.
Thanks to Fugang Duan <B38611@freescale.com> for spotting the error.
Shawn Guo [Tue, 26 Aug 2014 15:06:33 +0000 (23:06 +0800)]
ARM: imx: remove ENABLE and BYPASS bits from clk-pllv3 driver
Since ENABLE and BYPASS bits of PLLs are now implemented as separate
gate and mux clocks by clock drivers, the code handling these two bits
can be removed from clk-pllv3 driver.
This is the same change for imx6sx clock driver as "ARM: imx6q: add BYPASS
support for PLL clocks" for imx6q. The difference is that only anaclk1
is available on imx6sx.
This is the same change for imx6sl clock driver as "ARM: imx6q: add BYPASS
support for PLL clocks" for imx6q. The difference is that only anaclk1
is available on imx6sl.
The imx6q clock driver currently hard-codes all PLL clocks to source
from OSC24M without BYPASS support. The patch adds the missing lvds_in
clock which is mutually exclusive with lvds_gate, and implements BYPASS
and BYPASS_CLK_SRC selection for PLL clocks as per Figure 10-3. Primary
Clock Generation in IMX6DQRM, i.e. both BYPASS_CLK_SRC and BYPASS bits
are implemented as mux clocks, and ENABLE bit of PLL clocks is
implemented as a gate clock after BYPASS mux.
Shawn Guo [Tue, 26 Aug 2014 07:06:33 +0000 (15:06 +0800)]
ARM: imx: add an exclusive gate clock type
There are a couple of gate clocks are mutually exclusive on i.MX6, i.e.
LVDSCLK1_IBEN and LVDSCLK1_OBEN. They cannot be enabled simultaneously.
This patches adds an exclusive gate clock type specifically for such
case. The clock driver will need to call imx_clk_gate_exclusive() to
register a gate clock with parameter exclusive_mask indicating the mask
of gate bits which are mutually exclusive to this gate clock.
Right now, it only handles the exclusive gate clocks which are defined
in a single hardware register, which is the case we're running into
today. But it can be extended to handle exclusive gate clocks defined
in different registers later if needed.
ARM: clk-imx6sl: correct the pxp and epdc axi clock selections
The parent clocks of IMX6SL_CLK_PXP_AXI_SEL and IMX6SL_CLK_EPDC_AXI_SEL
clocks are not the same. So split the epdc_pxp_sels into two different
clock selections 'pxp_axi_sels' and 'epdc_axi_sels'.
Shengjiu Wang [Fri, 8 Aug 2014 07:02:47 +0000 (15:02 +0800)]
ARM: clk-imx6q: refine clock tree for ESAI
There are three clock for ESAI, esai_extal, esai_ipg, esai_mem. Rename
'esai' to 'esai_extal', 'esai_ahb' to 'esai_mem', and add 'esai_ipg'.
Make the clock for ESAI more clear and align them with imx6sx.
Signed-off-by: Shengjiu Wang <shengjiu.wang@freescale.com> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Stefan Agner [Tue, 29 Jul 2014 14:20:28 +0000 (16:20 +0200)]
ARM: imx: clk-vf610: introduce clks_init_on
At the end of the boot process, the clock framework might disable
required main PLL's. So far, this was no issue since drivers
requested clocks, which are descended of the main PLL's (e.g.
pll1_pfd1, which provides the system clock).
To archive the full 500MHz system clock, DDR clock need to be a
descendant of PLL2 rather than PLL1 (DDRC_CLK_SEL set to 0). The
bootloader sets up the clocks accordingly before making use of
DDR at all. However, in Linux, there is no driver using PLL2,
which lead to PLL2 being disabled by the clock framework.
With this patch, we make sure that the main system clock and the
DDR clock are initially enabled and are kept enabled.
Signed-off-by: Stefan Agner <stefan@agner.ch> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Jason Liu [Tue, 5 Nov 2013 04:03:18 +0000 (12:03 +0800)]
ARM: i.MX6: add more chip revision support
Add more revision support for the new i.MX6DQ tape-out (TO1.5). This
TO1.5 is the Rev 1.3 as documented in i.MX6DQ data sheet, because TO1.3
and TO1.4 are never revealed.
Signed-off-by: Jason Liu <r64343@freescale.com> Signed-off-by: Shawn Guo <shawn.guo@freescale.com> Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
With commit c716483c3db1 ("ARM: 8122/1: smp_scu: enable SCU standby
support"), the STANDBY bit of SCU is handled by core function
scu_enable(). So imx_scu_standby_enable() can be removed now.
pcm970-baseboard.c and mach-pcm038.c can be replaced with their
devicetree equivalents: imx27-phytec-phycore-rdk.dts and
imx27-phytec-phycore-som.dtsi respectively, so remove the board files.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Alexander Shiyan [Sat, 26 Jul 2014 13:41:08 +0000 (17:41 +0400)]
ARM: i.MX: Remove mach-cpuimx27sd board file
eukrea_mbimx27-baseboard.c and mach-cpuimx27.c can be replaced with their
devicetree equivalents: imx27-eukrea-mbimxsd27-baseboard.dts and
imx27-eukrea-cpuimx27.dtsi respectively, so remove the board files.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Acked-by: Eric Bénard <eric@eukrea.com> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Alexander Stein [Thu, 24 Jul 2014 07:05:21 +0000 (09:05 +0200)]
ARM: imx: iomux: Do not export symbol without public declaration
The iomux function declarations are in headers only accessible in this
directory. Thus those can't be used in any module. None of the
objects in this directory is tristate. Neither can the header be included
in out-of-tree modules.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Merge tag 'xtensa-20140830' of git://github.com/czankel/xtensa-linux
Pull Xtensa updates from Chris Zankel:
"Xtensa improvements for 3.17:
- support highmem on cores with aliasing data cache. Enable highmem
on kc705 by default
- simplify addition of new core variants (no need to modify Kconfig /
Makefiles)
- improve robustness of unaligned access handler and its interaction
with window overflow/underflow exception handlers
- deprecate atomic and spill registers syscalls
- clean up Kconfig: remove orphan MATH_EMULATION, sort 'select'
statements
- wire up renameat2 syscall.
Various fixes:
- fix address checks in dma_{alloc,free}_coherent (runtime BUG)
- fix access to THREAD_RA/THREAD_SP/THREAD_DS (debug build breakage)
- fix TLBTEMP_BASE_2 region handling in fast_second_level_miss
(runtime unrecoverable exception)
- fix a6 and a7 handling in fast_syscall_xtensa (runtime userspace
register clobbering)
- fix kernel/user jump out of fast_unaligned (potential runtime
unrecoverabl exception)
- replace termios IOCTL code definitions with constants (userspace
build breakage)"
* tag 'xtensa-20140830' of git://github.com/czankel/xtensa-linux: (25 commits)
xtensa: deprecate fast_xtensa and fast_spill_registers syscalls
xtensa: don't allow overflow/underflow on unaligned stack
xtensa: fix a6 and a7 handling in fast_syscall_xtensa
xtensa: allow single-stepping through unaligned load/store
xtensa: move invalid unaligned instruction handler closer to its users
xtensa: make fast_unaligned store restartable
xtensa: add double exception fixup handler for fast_unaligned
xtensa: fix kernel/user jump out of fast_unaligned
xtensa: configure kc705 for highmem
xtensa: support highmem in aliasing cache flushing code
xtensa: support aliasing cache in kmap
xtensa: support aliasing cache in k[un]map_atomic
xtensa: implement clear_user_highpage and copy_user_highpage
xtensa: fix TLBTEMP_BASE_2 region handling in fast_second_level_miss
xtensa: allow fixmap and kmap span more than one page table
xtensa: make fixmap region addressing grow with index
xtensa: fix access to THREAD_RA/THREAD_SP/THREAD_DS
xtensa: add renameat2 syscall
xtensa: fix address checks in dma_{alloc,free}_coherent
xtensa: replace IOCTL code definitions with constants
...
Guenter Roeck [Sun, 31 Aug 2014 18:14:26 +0000 (11:14 -0700)]
unicore32: Fix build error
unicore32 builds fail with
arch/unicore32/kernel/signal.c: In function ‘setup_frame’:
arch/unicore32/kernel/signal.c:257: error: ‘usig’ undeclared (first use in this function)
arch/unicore32/kernel/signal.c:279: error: ‘usig’ undeclared (first use in this function)
arch/unicore32/kernel/signal.c: In function ‘handle_signal’:
arch/unicore32/kernel/signal.c:306: warning: unused variable ‘tsk’
arch/unicore32/kernel/signal.c: In function ‘do_signal’:
arch/unicore32/kernel/signal.c:376: error: implicit declaration of function ‘get_signsl’
make[1]: *** [arch/unicore32/kernel/signal.o] Error 1
make: *** [arch/unicore32/kernel/signal.o] Error 2
Bisect points to commit 649671c90eaf ("unicore32: Use get_signal()
signal_setup_done()").
This code never even compiled. Reverting the patch does not work, since
previously used functions no longer exist, so try to fix it up. Compile
tested only.
Fixes: 649671c90eaf ("unicore32: Use get_signal() signal_setup_done()") Cc: Richard Weinberger <richard@nod.at> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge branch 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm
Pull ARM fixes from Russell King:
"Various assorted fixes:
- a couple of patches from Mark Rutland to resolve an errata with
Cortex-A15 CPUs.
- fix cpuidle for the CPU part ID changes in the last merge window
- add support for a relocation which ARM binutils is generating in
some circumstances"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 8130/1: cpuidle/cpuidle-big_little: fix reading cpu id part number
ARM: 8129/1: errata: work around Cortex-A15 erratum 830321 using dummy strex
ARM: 8128/1: abort: don't clear the exclusive monitors
ARM: 8127/1: module: add support for R_ARM_TARGET1 relocations
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Here's the weekly batch of fixes from arm-soc.
The delta is a largeish negative delta, due to revert of SMP support
for Broadcom's STB SoC -- it was accidentally merged before some
issues had been addressed, so they will make a new attempt for 3.18.
I didn't see a need for a full revert of the whole platform due to
this, we're keeping the rest enabled.
The rest is mostly:
- a handful of DT fixes for i.MX (Hummingboard/Cubox-i in particular)
- some MTD/NAND fixes for OMAP
- minor DT fixes for shmobile
- warning fix for UP builds on vexpress/spc
There's also a couple of patches that wires up hwmod on TI's DRA7 SoC
so it can boot. Drivers and the rest had landed for 3.17, and it's
small and isolated so it made sense to pick up now even if it's not a
bugfix"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (23 commits)
vexpress/spc: fix a build warning on array bounds
ARM: DRA7: hwmod: Add dra74x and dra72x specific ocp interface lists
ARM: DRA7: Add support for soc_is_dra74x() and soc_is_dra72x() variants
MAINTAINERS: catch special Rockchip code locations
ARM: dts: microsom-ar8035: MDIO pad must be set open drain
ARM: dts: omap54xx-clocks: Fix the l3 and l4 clock rates
ARM: brcmstb: revert SMP support
ARM: OMAP2+: hwmod: Rearm wake-up interrupts for DT when MUSB is idled
ARM: dts: Enable UART wake-up events for beagleboard
ARM: dts: Remove twl6030 clk32g "regulator"
ARM: OMAP2+: omap_device: remove warning that clk alias already exists
ARM: OMAP: fix %d confusingly prefixed with 0x in format string
ARM: dts: DRA7: fix interrupt-cells for GPIO
mtd: nand: omap: Fix 1-bit Hamming code scheme, omap_calculate_ecc()
ARM: dts: omap3430-sdp: Revert to using software ECC for NAND
ARM: OMAP2+: GPMC: Support Software ECC scheme via DT
mtd: nand: omap: Revert to using software ECC by default
ARM: dts: hummingboard/cubox-i: change SPDIF output to be more descriptive
ARM: dts: hummingboard/cubox-i: add USB OC pinctrl configuration
ARM: shmobile: r8a7791: add missing 0x0100 for SDCKCR
...
Alex Shi [Wed, 16 Jul 2014 11:21:56 +0000 (19:21 +0800)]
vexpress/spc: fix a build warning on array bounds
With ARCH_VEXPRESS_SPC option, kernel build has the following
warning:
arch/arm/mach-vexpress/spc.c: In function ‘ve_spc_clk_init’:
arch/arm/mach-vexpress/spc.c:431:38: warning: array subscript is below array bounds [-Warray-bounds]
struct ve_spc_opp *opps = info->opps[cluster];
^
since 'cluster' maybe '-1' in UP system. This patch does a active
checking to fix this issue.
Signed-off-by: Alex Shi <alex.shi@linaro.org> Acked-by: Pawel Moll <pawel.moll@arm.com> Acked-by: Sudeep Holla <sudeep.holla@arm.com> Signed-off-by: Olof Johansson <olof@lixom.net>
* tag 'for-v3.17-rc/omap-dra72x-d74x-support-a' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending:
ARM: DRA7: hwmod: Add dra74x and dra72x specific ocp interface lists
ARM: DRA7: Add support for soc_is_dra74x() and soc_is_dra72x() variants
Linus Torvalds [Sun, 31 Aug 2014 17:09:07 +0000 (10:09 -0700)]
Merge tag 'spi-v3.17-rc3-2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi bugfixes from Mark Brown:
"A smattering of bug fixes for the SPI subsystem, all in driver code
which has seen active work recently and none of them with any great
global impact.
There's also a new ACPI ID for the pxa2xx driver which required no
code changes and the addition of kerneldoc for some structure fields
that were missing it and generating warnings during documentation
builds as a result"
* tag 'spi-v3.17-rc3-2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: sh-msiof: Fix transmit-only DMA transfers
spi/rockchip: Avoid accidentally turning off the clock
spi: dw: fix kernel crash due to NULL pointer dereference
spi: dw-pci: fix bug when regs left uninitialized
spi: davinci: fix SPI_NO_CS functionality
spi/rockchip: fixup incorrect dma direction setting
spi/pxa2xx: Add ACPI ID for Intel Braswell
spi: spi-au1550: fix build failure
spi: rspi: Fix leaking of unused DMA descriptors
spi: sh-msiof: Fix leaking of unused DMA descriptors
spi: Add missing kerneldoc bits
spi/omap-mcspi: Fix the spi task hangs waiting dma_rx
Mark Brown [Sun, 31 Aug 2014 12:46:19 +0000 (13:46 +0100)]
Merge tag 'spi-v3.17-rc3' into spi-linus
spi: Bug fixes for v3.17
A smattering of bug fixes for the SPI subsystem, all in driver code
which has seen active work recently and none of them with any great
global impact.
There's also a new ACPI ID for the pxa2xx driver which required no code
changes and the addition of kerneldoc for some structure fields that
were missing it and generating warnings during documentation builds as a
result.
# gpg: Signature made Sun 31 Aug 2014 13:19:12 BST using RSA key ID 7EA229BD
# gpg: Good signature from "Mark Brown <broonie@sirena.org.uk>"
# gpg: aka "Mark Brown <broonie@debian.org>"
# gpg: aka "Mark Brown <broonie@kernel.org>"
# gpg: aka "Mark Brown <broonie@tardis.ed.ac.uk>"
# gpg: aka "Mark Brown <broonie@linaro.org>"
# gpg: aka "Mark Brown <Mark.Brown@linaro.org>"
Linus Torvalds [Sun, 31 Aug 2014 04:04:37 +0000 (21:04 -0700)]
Merge tag 'locks-v3.17-3' of git://git.samba.org/jlayton/linux
Pull file locking bugfx from Jeff Layton:
"Just a bugfix for a bug that crept in to v3.15. It's in a rather rare
error path, and I'm not aware of anyone having hit it, but it's worth
fixing for v3.17"
* tag 'locks-v3.17-3' of git://git.samba.org/jlayton/linux:
locks: pass correct "before" pointer to locks_unlink_lock in generic_add_lease
Linus Torvalds [Sat, 30 Aug 2014 00:22:27 +0000 (17:22 -0700)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Peter Anvin:
"One patch to avoid assigning interrupts we don't actually have on
non-PC platforms, and two patches that addresses bugs in the new
IOAPIC assignment code"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, irq, PCI: Keep IRQ assignment for runtime power management
x86: irq: Fix bug in setting IOAPIC pin attributes
x86: Fix non-PC platform kernel crash on boot due to NULL dereference
Linus Torvalds [Sat, 30 Aug 2014 00:18:48 +0000 (17:18 -0700)]
Merge tag 'pm+acpi-3.17-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael Wysocki:
- Fix for an ACPI regression related to the handling of fixed events
that caused netlink routines to be (incorrectly) run in interrupt
context from Lan Tianyu
- Fix for an ACPI EC driver regression on Acer Aspire V5-573G that
caused AC/battery plug/unplug and video brightness change
notifications to be delayed on that machine from Lv Zheng
- Fix for an ACPI device enumeration regression that caused ACPI driver
probe to fail for some devices where it succeeded before (Rafael J
Wysocki)
- intel_pstate driver fix to prevent it from printing an information
message for every CPU in the system on every boot from Andi Kleen
- s5pv210 cpufreq driver fix to remove an __init annotation from a
routine that in fact can be called at any time after init too from
Mark Brown
- New Intel Braswell device ID for the ACPI LPSS (Low-Power Subsystem)
driver from Alan Cox
- New Intel Braswell CPU ID for intel_pstate from Mika Westerberg
* tag 'pm+acpi-3.17-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: s5pv210: Remove spurious __init annotation
cpufreq: intel_pstate: Add CPU ID for Braswell processor
intel_pstate: Turn per cpu printk into pr_debug
ACPI / LPSS: Add ACPI IDs for Intel Braswell
ACPI / EC: Add support to disallow QR_EC to be issued before completing previous QR_EC
ACPI / EC: Add support to disallow QR_EC to be issued when SCI_EVT isn't set
ACPI: Run fixed event device notifications in process context
ACPI / scan: Allow ACPI drivers to bind to PNP device objects
Linus Torvalds [Fri, 29 Aug 2014 23:28:29 +0000 (16:28 -0700)]
Merge branch 'akpm' (fixes from Andrew Morton)
Merge patches from Andrew Morton:
"22 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (22 commits)
kexec: purgatory: add clean-up for purgatory directory
Documentation/kdump/kdump.txt: add ARM description
flush_icache_range: export symbol to fix build errors
tools: selftests: fix build issue with make kselftests target
ocfs2: quorum: add a log for node not fenced
ocfs2: o2net: set tcp user timeout to max value
ocfs2: o2net: don't shutdown connection when idle timeout
ocfs2: do not write error flag to user structure we cannot copy from/to
x86/purgatory: use approprate -m64/-32 build flag for arch/x86/purgatory
drivers/rtc/rtc-s5m.c: re-add support for devices without irq specified
xattr: fix check for simultaneous glibc header inclusion
kexec: remove CONFIG_KEXEC dependency on crypto
kexec: create a new config option CONFIG_KEXEC_FILE for new syscall
x86,mm: fix pte_special versus pte_numa
hugetlb_cgroup: use lockdep_assert_held rather than spin_is_locked
mm/zpool: use prefixed module loading
zram: fix incorrect stat with failed_reads
lib: turn CONFIG_STACKTRACE into an actual option.
mm: actually clear pmd_numa before invalidating
memblock, memhotplug: fix wrong type in memblock_find_in_range_node().
...
Junxiao Bi [Fri, 29 Aug 2014 22:19:02 +0000 (15:19 -0700)]
ocfs2: o2net: set tcp user timeout to max value
When tcp retransmit timeout(15mins), the connection will be closed.
Pending messages may be lost during this time. So we set tcp user
timeout to override the retransmit timeout to the max value. This is OK
for ocfs2 since we have disk heartbeat, if peer crash, the disk
heartbeat will timeout and it will be evicted, if disk heartbeat not
timeout and connection idle for a long time, then this means the cluster
enters split-brain state, since fence can't happen, we'd better keep the
connection and wait network recover.
Signed-off-by: Junxiao Bi <junxiao.bi@oracle.com> Reviewed-by: Srinivas Eeda <srinivas.eeda@oracle.com> Reviewed-by: Mark Fasheh <mfasheh@suse.de> Cc: Joel Becker <jlbec@evilplan.org> Cc: Joseph Qi <joseph.qi@huawei.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Junxiao Bi [Fri, 29 Aug 2014 22:19:00 +0000 (15:19 -0700)]
ocfs2: o2net: don't shutdown connection when idle timeout
This patch series is to fix a possible message lost bug in ocfs2 when
network go bad. This bug will cause ocfs2 hung forever even network
become good again.
The messages may lost in this case. After the tcp connection is
established between two nodes, an idle timer will be set to check its
state periodically, if no messages are received during this time, idle
timer will timeout, it will shutdown the connection and try to
reconnect, so pending messages in tcp queues will be lost. This
messages may be from dlm. Dlm may get hung in this case. This may
cause the whole ocfs2 cluster hung.
This is very possible to happen when network state goes bad. Do the
reconnect is useless, it will fail if network state is still bad. Just
waiting there for network recovering may be a good idea, it will not
lost messages and some node will be fenced until cluster goes into
split-brain state, for this case, Tcp user timeout is used to override
the tcp retransmit timeout. It will timeout after 25 days, user should
have notice this through the provided log and fix the network, if they
don't, ocfs2 will fall back to original reconnect way.
This patch (of 3):
Some messages in the tcp queue maybe lost if we shutdown the connection
and reconnect when idle timeout. If packets lost and reconnect success,
then the ocfs2 cluster maybe hung.
To fix this, we can leave the connection there and do the fence decision
when idle timeout, if network recover before fence dicision is made, the
connection survive without lost any messages.
This bug can be saw when network state go bad. It may cause ocfs2 hung
forever if some packets lost. With this fix, ocfs2 will recover from
hung if network becomes good again.
Signed-off-by: Junxiao Bi <junxiao.bi@oracle.com> Reviewed-by: Srinivas Eeda <srinivas.eeda@oracle.com> Reviewed-by: Mark Fasheh <mfasheh@suse.de> Cc: Joel Becker <jlbec@evilplan.org> Cc: Joseph Qi <joseph.qi@huawei.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ben Hutchings [Fri, 29 Aug 2014 22:18:58 +0000 (15:18 -0700)]
ocfs2: do not write error flag to user structure we cannot copy from/to
If we failed to copy from the structure, writing back the flags leaks 31
bits of kernel memory (the rest of the ir_flags field).
In any case, if we cannot copy from/to the structure, why should we
expect putting just the flags to work?
Also make sure ocfs2_info_handle_freeinode() returns the right error
code if the copy_to_user() fails.
Fixes: ddee5cdb70e6 ('Ocfs2: Add new OCFS2_IOC_INFO ioctl for ocfs2 v8.') Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Cc: Joel Becker <jlbec@evilplan.org> Acked-by: Mark Fasheh <mfasheh@suse.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Vivek Goyal [Fri, 29 Aug 2014 22:18:55 +0000 (15:18 -0700)]
x86/purgatory: use approprate -m64/-32 build flag for arch/x86/purgatory
Thomas reported that build of x86_64 kernel was failing for him. He is
using 32bit tool chain.
Problem is that while compiling purgatory, I have not specified -m64
flag. And 32bit tool chain must be assuming -m32 by default.
Following is error message.
(mini) [~/work/linux-2.6] make
scripts/kconfig/conf --silentoldconfig Kconfig
CHK include/config/kernel.release
UPD include/config/kernel.release
CHK include/generated/uapi/linux/version.h
CHK include/generated/utsrelease.h
UPD include/generated/utsrelease.h
CC arch/x86/purgatory/purgatory.o
arch/x86/purgatory/purgatory.c:1:0: error: code model 'large' not supported in
the 32 bit mode
Fix it by explicitly passing appropriate -m64/-m32 build flag for
purgatory.
Reported-by: Thomas Glanzmann <thomas@glanzmann.de> Tested-by: Thomas Glanzmann <thomas@glanzmann.de> Suggested-by: H. Peter Anvin <hpa@zytor.com> Signed-off-by: Vivek Goyal <vgoyal@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
xattr: fix check for simultaneous glibc header inclusion
The guard was introduced in commit ea1a8217b06b ("xattr: guard against
simultaneous glibc header inclusion") but it is using #ifdef to check
for a define that is either set to 1 or 0. Fix it to use #if instead.
* Without this patch:
$ { echo "#include <sys/xattr.h>"; echo "#include <linux/xattr.h>"; } | gcc -E -Iinclude/uapi - >/dev/null
include/uapi/linux/xattr.h:19:0: warning: "XATTR_CREATE" redefined [enabled by default]
#define XATTR_CREATE 0x1 /* set value, fail if attr already exists */
^
/usr/include/x86_64-linux-gnu/sys/xattr.h:32:0: note: this is the location of the previous definition
#define XATTR_CREATE XATTR_CREATE
^
Vivek Goyal [Fri, 29 Aug 2014 22:18:46 +0000 (15:18 -0700)]
kexec: create a new config option CONFIG_KEXEC_FILE for new syscall
Currently new system call kexec_file_load() and all the associated code
compiles if CONFIG_KEXEC=y. But new syscall also compiles purgatory
code which currently uses gcc option -mcmodel=large. This option seems
to be available only gcc 4.4 onwards.
Hiding new functionality behind a new config option will not break
existing users of old gcc. Those who wish to enable new functionality
will require new gcc. Having said that, I am trying to figure out how
can I move away from using -mcmodel=large but that can take a while.
I think there are other advantages of introducing this new config
option. As this option will be enabled only on x86_64, other arches
don't have to compile generic kexec code which will never be used. This
new code selects CRYPTO=y and CRYPTO_SHA256=y. And all other arches had
to do this for CONFIG_KEXEC. Now with introduction of new config
option, we can remove crypto dependency from other arches.
Now CONFIG_KEXEC_FILE is available only on x86_64. So whereever I had
CONFIG_X86_64 defined, I got rid of that.
For CONFIG_KEXEC_FILE, instead of doing select CRYPTO=y, I changed it to
"depends on CRYPTO=y". This should be safer as "select" is not
recursive.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com> Cc: Eric Biederman <ebiederm@xmission.com> Cc: H. Peter Anvin <hpa@zytor.com> Tested-by: Shaun Ruffell <sruffell@digium.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Hugh Dickins [Fri, 29 Aug 2014 22:18:44 +0000 (15:18 -0700)]
x86,mm: fix pte_special versus pte_numa
Sasha Levin has shown oopses on ffffea0003480048 and ffffea0003480008 at
mm/memory.c:1132, running Trinity on different 3.16-rc-next kernels:
where zap_pte_range() checks page->mapping to see if PageAnon(page).
Those addresses fit struct pages for pfns d2001 and d2000, and in each
dump a register or a stack slot showed d2001730 or d2000730: pte flags
0x730 are PCD ACCESSED PROTNONE SPECIAL IOMAP; and Sasha's e820 map has
a hole between cfffffff and 100000000, which would need special access.
Commit c46a7c817e66 ("x86: define _PAGE_NUMA by reusing software bits on
the PMD and PTE levels") has broken vm_normal_page(): a PROTNONE SPECIAL
pte no longer passes the pte_special() test, so zap_pte_range() goes on
to try to access a non-existent struct page.
Fix this by refining pte_special() (SPECIAL with PRESENT or PROTNONE) to
complement pte_numa() (SPECIAL with neither PRESENT nor PROTNONE). A
hint that this was a problem was that c46a7c817e66 added pte_numa() test
to vm_normal_page(), and moved its is_zero_pfn() test from slow to fast
path: This was papering over a pte_special() snag when the zero page was
encountered during zap. This patch reverts vm_normal_page() to how it
was before, relying on pte_special().
It still appears that this patch may be incomplete: aren't there other
places which need to be handling PROTNONE along with PRESENT? For
example, pte_mknuma() clears _PAGE_PRESENT and sets _PAGE_NUMA, but on a
PROT_NONE area, that would make it pte_special(). This is side-stepped
by the fact that NUMA hinting faults skipped PROT_NONE VMAs and there
are no grounds where a NUMA hinting fault on a PROT_NONE VMA would be
interesting.
Fixes: c46a7c817e66 ("x86: define _PAGE_NUMA by reusing software bits on the PMD and PTE levels") Reported-by: Sasha Levin <sasha.levin@oracle.com> Tested-by: Sasha Levin <sasha.levin@oracle.com> Signed-off-by: Hugh Dickins <hughd@google.com> Signed-off-by: Mel Gorman <mgorman@suse.de> Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Rik van Riel <riel@redhat.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Cyrill Gorcunov <gorcunov@gmail.com> Cc: Matthew Wilcox <matthew.r.wilcox@intel.com> Cc: <stable@vger.kernel.org> [3.16] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Michal Hocko [Fri, 29 Aug 2014 22:18:42 +0000 (15:18 -0700)]
hugetlb_cgroup: use lockdep_assert_held rather than spin_is_locked
spin_lock may be an empty struct for !SMP configurations and so
arch_spin_is_locked may return unconditional 0 and trigger the VM_BUG_ON
even when the lock is held.
Replace spin_is_locked by lockdep_assert_held. We will not BUG anymore
but it is questionable whether crashing makes a lot of sense in the
uncharge path. Uncharge happens after the last page reference was
released so nobody should touch the page and the function doesn't update
any shared state except for res counter which uses synchronization of
its own.
Signed-off-by: Michal Hocko <mhocko@suse.cz> Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Kees Cook [Fri, 29 Aug 2014 22:18:40 +0000 (15:18 -0700)]
mm/zpool: use prefixed module loading
To avoid potential format string expansion via module parameters, do not
use the zpool type directly in request_module() without a format string.
Additionally, to avoid arbitrary modules being loaded via zpool API
(e.g. via the zswap_zpool_type module parameter) add a "zpool-" prefix
to the requested module, as well as module aliases for the existing
zpool types (zbud and zsmalloc).
Signed-off-by: Kees Cook <keescook@chromium.org> Cc: Seth Jennings <sjennings@variantweb.net> Cc: Minchan Kim <minchan@kernel.org> Cc: Nitin Gupta <ngupta@vflare.org> Acked-by: Dan Streetman <ddstreet@ieee.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Chao Yu [Fri, 29 Aug 2014 22:18:37 +0000 (15:18 -0700)]
zram: fix incorrect stat with failed_reads
Since we allocate a temporary buffer in zram_bvec_read to handle partial
page operations in commit 924bd88d703e ("Staging: zram: allow partial
page operations"), our ->failed_reads value may be incorrect as we do
not increase its value when failing to allocate the temporary buffer.
Let's fix this issue and correct the annotation of failed_reads.