Robert Jarzmik [Sat, 2 Jan 2016 20:00:57 +0000 (21:00 +0100)]
ARM: pxa: add defconfig covering all the boards
Add a defconfig covering all known pxa board, ie. all selectable machine
files in arch/arm/mach-pxa/*.c.
This defconfig was built by doing :
- aggregation of all known defconfigs by cat
am200epdkit_defconfig
cm_x2xx_defconfig
cm_x300_defconfig
colibri_pxa270_defconfig
colibri_pxa300_defconfig
corgi_defconfig
em_x270_defconfig
eseries_pxa_defconfig
ezx_defconfig
h5000_defconfig
imote2_defconfig
lpd270_defconfig
lubbock_defconfig
magician_defconfig
mainstone_defconfig
multi_v7_defconfig
palmz72_defconfig
pcm027_defconfig
pxa255-idp_defconfig
pxa3xx_defconfig
raumfeld_defconfig
spitz_defconfig
trizeps4_defconfig
viper_defconfig
xcep_defconfig
zeus_defconfig
- manual make menuconfig to ensure :
- all pxa implementation were selected
- all drivers were transformed into modules rather than builtin
=> as a consequence this single kernel will rely on an initramfs
=> as kernel size matters on pxa, each machine can take the subset
of modules required for it to work
- all missed configurations are selected verified by :
=> grep -i pxa .config | grep "is not set"
=> this should only show the left on purpose options (either not
selectable or sharpsl exception below)
- CONFIG_PXA_SHARPSL was disabled
This breaks the boot very early on any non Sharp platform, see
head-sharpsl.S
This defconfig was tested as booting up to the login phase on :
- lubbock (pxa25x)
- mainstone (pxa27x)
- zylonite (pxa3xx)
The completion of this work will require to :
- parse manually all the arch/arm/mach-pxa/*c files, look for all
platform devices added, and verify they are all in pxa_defconfig
- do the same to ensure all pxa specific drivers (leds, gpio, ...) are
included
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Linus Walleij [Tue, 5 Jan 2016 08:59:20 +0000 (09:59 +0100)]
ARM: versatile: select some defaults in defconfig
This updates the Versatile defconfig to:
- Use NO_HZ_IDLE and HIGH_RES_TIMERS
- Enable the I2C driver
- Enable the SPI driver
- Enable the RTC driver for DS1338 as found on the Versatile
boards
- Compile in the MMCI MMC driver, which is good if you
want to mount a root FS on the MMC card without having
to first load this module from an initramfs
Patch tested on the Versatile AB, QEMU for Versatile AB
and QEMU for Versatile PB.
Cc: Rob Herring <robh@kernel.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Olof Johansson <olof@lixom.net>
ARM: multi_v7_defconfig: Enable fan, sensors and audio for Odroid XU3
For Odroid XU3-family enable the:
- PWM fan (to control the CPU fan using thermal subsystem),
- TI INA231 sensors (provide power measurements of big.LITTLE cores,
DRAM and GPU),
- Samsung sound (for Odroid XU3 and Snow as well).
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Olof Johansson <olof@lixom.net>
Stefan Wahren [Tue, 27 Oct 2015 18:08:58 +0000 (19:08 +0100)]
ARM: bcm2835: enable all bcm2835-relevant in defconfig
Rebuild bcm2835_defconfig using "make bcm2835_defconfig;
make savedefconfig", and enable manually the following features:
* all bcm2835-relevant drivers (MBOX, WDT, DMA, PWM, SND)
* enable regular stackprotector because CONFIG_CC_STACKPROTECTOR
disappear
* enable some new dependencies in order to keep LED heartbeat
( CONFIG_NEW_LEDS, CONFIG_LEDS_CLASS, CONFIG_LEDS_TRIGGERS )
The following options were removed, because they are enabled implicit:
Arnd Bergmann [Fri, 18 Dec 2015 22:44:23 +0000 (23:44 +0100)]
ARM: default to multi_v7_defconfig
versatile_defconfig has not been a reasonable default for a very long
time, there is very little work happening on this platform and it's
based on an old ARM926 CPU core.
This changes the default to multi_v7_defconfig, which is much more
relevant to anyone doing a build test on ARM, as it covers a wide
range of platforms.
Olof Johansson [Tue, 22 Dec 2015 23:00:22 +0000 (15:00 -0800)]
Merge tag 'imx-defconfig-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/defconfig
The i.MX defconfig updates for 4.5:
- Drop CONFIG_SOC_LS1021A support, as it needs LPAE which is not
available with imx_v6_v7_defconfig.
- Enable VF610_ADC, HDMI audio and PCI_MSI support
* tag 'imx-defconfig-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: imx_v6_v7_defconfig: enable PCI_MSI
ARM: imx_v6_v7_defconfig: Select HDMI audio support
ARM: imx_v6_v7_defconfig: Select VF610_ADC
ARM: imx_v6_v7_defconfig: Remove CONFIG_SOC_LS1021A
The rk808 supplies two clock outputs with one going back into the soc as
32kHz supply, supplying some core soc clocks with it. The system can boot
without it being present, but it is needed for example as source clock
for the thermal driver.
Signed-off-by: Heiko Stuebner <heiko.stuebner@collabora.com> Signed-off-by: Olof Johansson <olof@lixom.net>
The io-domain driver is necessary to notify the soc about voltages changes
happening on supplying regulators. Probably the most important user right
now is the mmc tuning code, where the soc needs to get notified when the
voltage is dropped to the 1.8V point.
As this option is necessary to sucessfully tune UHS cards etc, it should
get built in.
Signed-off-by: Heiko Stuebner <heiko.stuebner@collabora.com> Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Tue, 22 Dec 2015 19:48:45 +0000 (11:48 -0800)]
Merge tag 'renesas-defconfig-for-v4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/defconfig
Renesas ARM Based SoC Defconfig Updates for v4.5
* multi_v7_defconfig and shmobile_defconfig:
- Enable frame buffer console for armadillo800eva
- Enable missing Renesas ARM support based on DTSes
- Drop useless CONFIG_USB_RCAR_PHY=y
* shmobile_defconfig only:
- Enable CONFIG_PRINTK_TIME
* tag 'renesas-defconfig-for-v4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: multi_v7_defconfig: Enable frame buffer console for armadillo800eva
ARM: multi_v7_defconfig: Enable missing Renesas ARM support based on DTSes
ARM: multi_v7_defconfig: Drop useless CONFIG_USB_RCAR_PHY=y
ARM: shmobile: defconfig: Enable frame buffer console for armadillo800eva
ARM: shmobile: defconfig: Enable missing support based on DTSes
ARM: shmobile: defconfig: Drop useless CONFIG_USB_RCAR_PHY=y
ARM: shmobile: defconfig: Enable CONFIG_PRINTK_TIME
Signed-off-by: Olof Johansson <olof@lixom.net>
Conflicts:
arch/arm/configs/multi_v7_defconfig
Olof Johansson [Tue, 22 Dec 2015 19:47:27 +0000 (11:47 -0800)]
Merge tag 'at91-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91 into next/defconfig
First defconfig pull-request for 4.5:
- a single patch to add watchdog drivers to sama5_defconfig
* tag 'at91-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
ARM: at91/defconfig: enable watchdog drivers in sama5_defconfig
ABB and PBIAS are internal LDO control regulators that are needed for
maintaining proper functionality of OMAP architecture SoCs. Enable the
same. PBIAS is already enabled, so just enable ABB regulator as well.
Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Olof Johansson <olof@lixom.net>
Enable PMIC for AM437x platforms such as AM437x-sk similar to commit a186cf10da84 ("ARM: omap2plus_defconfig: enable TPS65218 configs").
This allows multi_v7_defconfig to boot up on AM437x-sk platform.
Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Tue, 22 Dec 2015 04:56:33 +0000 (20:56 -0800)]
Merge tag 'samsung-defconfig-4.5' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/defconfig
Defconfig (exynos and multi_v7) changes for Exynos based boards for 4.5:
1. Enable Maxim 8997 and 77693 family drivers (charger, extcon, LED,
RTC, haptic/motor, regulator).
2. Build ChromeOS EC drivers as modules on multi_v7.
3. Enable drivers important for Exynos4210-based Universal C210 board.
4. Enable NFSv4 client.
5. On exynos_defconfig set some options to a value recommended
by systemd. This also makes it more consistent with multi_v7.
* tag 'samsung-defconfig-4.5' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: exynos_defconfig: Set recommended options for systemd
ARM: exynos_defconfig: Enable NFSv4 client
ARM: exynos_defconfig: Add drivers for Exynos4210 Universal C210 board
ARM: multi_v7_defconfig: Build ChromeOS EC drivers as modules
ARM: multi_v7_defconfig: Enable Maxim 77693 LED and haptic drivers
ARM: multi_v7_defconfig: Enable Maxim 8997 family drivers
ARM: exynos_defconfig: Enable Maxim 77693 LED and haptic drivers
ARM: exynos_defconfig: Enable Maxim 8997 family drivers
Enable TPS65217 regulator to have rootfs in MMC for Beagle Bone's.
Suggested-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Afzal Mohammed <afzal.mohd.ma@gmail.com> Signed-off-by: Olof Johansson <olof@lixom.net>
Linus Walleij [Fri, 18 Dec 2015 13:32:16 +0000 (14:32 +0100)]
ARM: realview: select apropriate targets
Now that we have multiplatform support, let the RealView
defconfigs select all the RealView boards so we boot out of
the box like before. This updates both defconfigs.
Bjorn Andersson [Wed, 21 Oct 2015 04:57:50 +0000 (21:57 -0700)]
ARM: defconfig: Update qcom_defconfig
This enables smem, smd, rpm, regulators, pmic pinctrl and hwspinlock as
these platform features are now merged. It enables gpio-keys as this is
used by most boards and enables fhandle and cgroups, so we can boot
systemd.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com> Signed-off-by: Andy Gross <andy.gross@linaro.org>
ARM: multi_v7_defconfig: Enable Rockchip generic power domain.
In order to meet high performance an low power requirement for Rockchip
enable the power domain support. The patch also fixes a drm/kms issue,
driver deferring untils power-domains are available)
Arnd Bergmann [Tue, 15 Dec 2015 16:53:37 +0000 (17:53 +0100)]
Merge tag 'socfpga_defconfig_for_v4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux into next/defconfig
Merge "SoCFPGA defconfig update for v4.5" from Dinh Nguyen:
-Enable USB OTG dual-role and some cleanup by make savedefconfig
* tag 'socfpga_defconfig_for_v4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
arm: socfpga_defconfig: enable USB dual-role and cleanup
Linus Walleij [Thu, 10 Dec 2015 12:24:54 +0000 (13:24 +0100)]
ARM: realview: add generic config options
This adds a few features that are available on some
or all of the RealView but never made it into the SMP
defconfig file:
- Full tickless idle
- High resolution timers
- Perf events and HW perf events from the PMU
- MTD AFS partition handling
- MTD ROM partition handling
- USB and ISP1760 USB driver
Linus Walleij [Thu, 10 Dec 2015 12:27:59 +0000 (13:27 +0100)]
ARM: realview: add generic config options
This adds a few features that are available on some
or all of the RealView but never made it into the defconfig
file:
- High-resolution timers
- Perf events and HW perf events from the PMU
- MTD AFS partition handling
- MTD ROM partition handling
- USB and ISP1760 USB driver
Alison Wang [Wed, 9 Dec 2015 08:41:39 +0000 (16:41 +0800)]
ARM: multi_v7_defconfig: Enable some drivers for LS1021A
This patch enables some drivers for LS1021A, such as
GIANFAR, WATCHDOG, AUDIO, QSPI, I2C, ESDHC, EDMA, FTM.
QorIQ Clock Framework and Ramdisk support is also enabled.
Signed-off-by: Alison Wang <alison.wang@freescale.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Tue, 15 Dec 2015 16:43:36 +0000 (17:43 +0100)]
Merge tag 'sunxi-defconfig-for-4.5' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into next/defconfig
Merge "Allwinner defconfig changes for 4.5" from Maxime Ripard:
A bunch of patches to enable new drivers related to Allwinner SoCs.
* tag 'sunxi-defconfig-for-4.5' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
ARM: sunxi: Clean up sunxi_defconfig
ARM: sunxi: Really enable LRADC keys in sunxi_defconfig
ARM: sunxi: Re-enable SID driver in sunxi_defconfig
ARM: sunxi: Re-enable SID driver in multi_v7_defconfig
ARM: multi_v7_defconfig: Enable RSB and AXP20X related drivers as modules
ARM: sunxi_defconfig: Update MFD_AXP20X symbol and enable MFD_AXP20X_RSB
ARM: shmobile: defconfig: Enable frame buffer console for armadillo800eva
Enabling the frame buffer device on armadillo800eva requires the board
staging code.
Also enable the frame buffer, so you will actually see output during
boot.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Bjorn Andersson [Tue, 1 Dec 2015 22:47:50 +0000 (14:47 -0800)]
ARM: defconfig: multi_v7: Enable Qualcomm options for Honami
The Honami device does not boot due to the lack of pinctrl support
compiled in with the multi_v7_defconfig. This patch correct this and
enables coincell, sdhci, smsm, smp2p and wcnss_ctrl as well, all found
on a variety of Qualcomm boards.
Reported-by: Kevin Hilman <khilman@linaro.org> Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com> Tested-by: Kevin Hilman <khilman@linaro.org> Signed-off-by: Kevin Hilman <khilman@linaro.org>
Lucas Stach [Mon, 30 Nov 2015 17:00:11 +0000 (18:00 +0100)]
ARM: imx_v6_v7_defconfig: enable PCI_MSI
This has been stable on i.MX6 for a good while now and there is no
reason to keep it disabled, as it allows to allocate non-shared
IRQs if several PCIe devices are connected to a single host.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Sjoerd Simons [Fri, 6 Nov 2015 12:22:24 +0000 (13:22 +0100)]
drm/rockchip: vop: Correct enabled clocks during setup
When doing the initial setup both the hclk and the aclk need to be
enabled otherwise the board will simply hang. This only occurs when
building the vop driver as a module, when its built-in the initial setup
happens to run before the clock framework shuts of unused clocks
(including the aclk).
While there also switch to doing prepare and enable in one step rather
then separate steps to reduce the amount of code required.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk> Acked-by: Mark Yao <mark.yao@rock-chips.com> Tested-by: Yakir Yang <ykk@rock-chips.com> Tested-by: Romain Perier <romain.perier@gmail.com>
ARM: exynos_defconfig: Set recommended options for systemd
Set following options to a value recommended by systemd (which also
matches the multi_v7 deconfig):
1. Enable AUTOFS4_FS - for systemd.automount [0];
2. Enable BLK_DEV_BSG - SG v4 for recend udev [0][1];
3. Disable UEVENT_HELPER_PATH - legacy hook for hotplug, forked for each
uevent, slows down booting [0];
Dave Airlie [Mon, 30 Nov 2015 22:00:33 +0000 (08:00 +1000)]
Merge tag 'drm-intel-fixes-2015-11-30' of git://anongit.freedesktop.org/drm-intel into drm-fixes
few i915 fixes.
* tag 'drm-intel-fixes-2015-11-30' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Don't override output type for DDI HDMI
drm/i915: Don't compare has_drrs strictly in pipe config
drm/i915: Mark uneven memory banks on gen4 desktop as unknown swizzling
NFS client is already enabled (NFS_FS) and by default it enables clients
for version 2 and 3. Enable explicitly the version 4 client to utilize
the newer protocol.
The NFS client is especially useful for testing kernel in automated
environments (network boot with network file system).
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Linus Torvalds [Mon, 30 Nov 2015 01:38:08 +0000 (17:38 -0800)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull nouveau and radeon fixes from Dave Airlie:
"Just some nouveau and radeon/amdgpu fixes.
The nouveau fixes look large as the firmware context files are
regenerated, but the actual change is quite small"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon: make some dpm errors debug only
drm/nouveau/volt/pwm/gk104: fix an off-by-one resulting in the voltage not being set
drm/nouveau/nvif: allow userspace access to its own client object
drm/nouveau/gr/gf100-: fix oops when calling zbc methods
drm/nouveau/gr/gf117-: assume no PPC if NV_PGRAPH_GPC_GPM_PD_PES_TPC_ID_MASK is zero
drm/nouveau/gr/gf117-: read NV_PGRAPH_GPC_GPM_PD_PES_TPC_ID_MASK from correct GPC
drm/nouveau/gr/gf100-: split out per-gpc address calculation macro
drm/nouveau/bios: return actual size of the buffer retrieved via _ROM
drm/nouveau/instmem: protect instobj list with a spinlock
drm/nouveau/pci: enable c800 magic for some unknown Samsung laptop
drm/nouveau/pci: enable c800 magic for Clevo P157SM
drm/radeon: make rv770_set_sw_state failures non-fatal
drm/amdgpu: move dependency handling out of atomic section v2
drm/amdgpu: optimize scheduler fence handling
drm/amdgpu: remove vm->mutex
drm/amdgpu: add mutex for ba_va->valids/invalids
drm/amdgpu: adapt vce session create interface changes
drm/amdgpu: vce use multiple cache surface starting from stoney
drm/amdgpu: reset vce trap interrupt flag
Linus Torvalds [Mon, 30 Nov 2015 01:30:41 +0000 (17:30 -0800)]
Merge tag 'rtc-4.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC fixes from Alexandre Belloni:
"Two fixes for the ds1307 alarm and wakeup"
* tag 'rtc-4.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
rtc: ds1307: fix alarm reading at probe time
rtc: ds1307: fix kernel splat due to wakeup irq handling
Pull SCSI target fixes from Nicholas Bellinger:
- fix tcm-user backend driver expired cmd time processing (agrover)
- eliminate kref_put_spinlock_irqsave() for I/O completion (bart)
- fix iscsi login kthread failure case hung task regression (nab)
- fix COMPARE_AND_WRITE completion use-after-free race (nab)
- fix COMPARE_AND_WRITE with SCF_PASSTHROUGH_SG_TO_MEM_NOALLOC non zero
SGL offset data corruption. (Jan + Doug)
- fix >= v4.4-rc1 regression for tcm_qla2xxx enable configfs attribute
(Himanshu + HCH)
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
target/stat: print full t10_wwn.model buffer
target: fix COMPARE_AND_WRITE non zero SGL offset data corruption
qla2xxx: Fix regression introduced by target configFS changes
kref: Remove kref_put_spinlock_irqsave()
target: Invoke release_cmd() callback without holding a spinlock
target: Fix race for SCF_COMPARE_AND_WRITE_POST checking
iscsi-target: Fix rx_login_comp hang after login failure
iscsi-target: return -ENOMEM instead of -1 in case of failed kmalloc()
target/user: Do not set unused fields in tcmu_ops
target/user: Fix time calc in expired cmd processing
Linus Torvalds [Sun, 29 Nov 2015 16:58:48 +0000 (08:58 -0800)]
Merge branch 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux
Pull thermal management fixes from Zhang Rui:
"Specifics:
- several fixes and cleanups on Rockchip thermal drivers.
- add the missing support of RK3368 SoCs in Rockchip driver.
- small fixes on of-thermal, power_allocator, rcar driver, IMX, and
QCOM drivers, and also compilation fixes, on thermal.h, when thermal
is not selected"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
imx: thermal: use CPU temperature grade info for thresholds
thermal: fix thermal_zone_bind_cooling_device prototype
Revert "thermal: qcom_spmi: allow compile test"
thermal: rcar_thermal: remove redundant operation
thermal: of-thermal: Reduce log level for message when can't fine thermal zone
thermal: power_allocator: Use temperature reading from tz
thermal: rockchip: Support the RK3368 SoCs in thermal driver
thermal: rockchip: consistently use int for temperatures
thermal: rockchip: Add the sort mode for adc value increment or decrement
thermal: rockchip: improve the conversion function
thermal: rockchip: trivial: fix typo in commit
thermal: rockchip: better to compatible the driver for different SoCs
dt-bindings: rockchip-thermal: Support the RK3368 SoCs compatible
Jan Engelhardt [Mon, 23 Nov 2015 16:46:32 +0000 (17:46 +0100)]
target: fix COMPARE_AND_WRITE non zero SGL offset data corruption
target_core_sbc's compare_and_write functionality suffers from taking
data at the wrong memory location when writing a CAW request to disk
when a SGL offset is non-zero.
This can happen with loopback and vhost-scsi fabric drivers when
SCF_PASSTHROUGH_SG_TO_MEM_NOALLOC is used to map existing user-space
SGL memory into COMPARE_AND_WRITE READ/WRITE payload buffers.
Rather than writing all-zeroes as instructed with the -D file, it
corrupts the data in the sector by splicing some of the original
bytes in. The page of the first entry of cmd->t_data_sg includes the
CDB, and sg->offset is set to a position past the CDB. I presume that
sg->offset is also the right choice to use for subsequent sglist
members.
Signed-off-by: Jan Engelhardt <jengelh@netitwork.de> Tested-by: Douglas Gilbert <dgilbert@interlog.com> Cc: <stable@vger.kernel.org> # v3.12+ Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Fixes: 2eafd72939fd ("target: use per-attribute show and store methods") Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com> Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Bart Van Assche [Thu, 22 Oct 2015 22:57:04 +0000 (15:57 -0700)]
target: Invoke release_cmd() callback without holding a spinlock
This patch fixes the following kernel warning because it avoids that
IRQs are disabled while ft_release_cmd() is invoked (fc_seq_set_resp()
invokes spin_unlock_bh()):
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com> Acked-by: Joern Engel <joern@logfs.org> Reviewed-by: Andy Grover <agrover@redhat.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Hannes Reinecke <hare@suse.de> Cc: Sagi Grimberg <sagig@mellanox.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
target: Fix race for SCF_COMPARE_AND_WRITE_POST checking
This patch addresses a race + use after free where the first
stage of COMPARE_AND_WRITE in compare_and_write_callback()
is rescheduled after the backend sends the secondary WRITE,
resulting in second stage compare_and_write_post() callback
completing in target_complete_ok_work() before the first
can return.
Because current code depends on checking se_cmd->se_cmd_flags
after return from se_cmd->transport_complete_callback(),
this results in first stage having SCF_COMPARE_AND_WRITE_POST
set, which incorrectly falls through into second stage CAW
processing code, eventually triggering a NULL pointer
dereference due to use after free.
To address this bug, pass in a new *post_ret parameter into
se_cmd->transport_complete_callback(), and depend upon this
value instead of ->se_cmd_flags to determine when to return
or fall through into ->queue_status() code for CAW.
iscsi-target: Fix rx_login_comp hang after login failure
This patch addresses a case where iscsi_target_do_tx_login_io()
fails sending the last login response PDU, after the RX/TX
threads have already been started.
The case centers around iscsi_target_rx_thread() not invoking
allow_signal(SIGINT) before the send_sig(SIGINT, ...) occurs
from the failure path, resulting in RX thread hanging
indefinately on iscsi_conn->rx_login_comp.
To address this bug, complete ->rx_login_complete for good
measure in the failure path, and immediately return from
RX thread context if connection state did not actually reach
full feature phase (TARG_CONN_STATE_LOGGED_IN).
iscsi-target: return -ENOMEM instead of -1 in case of failed kmalloc()
Smatch complains about returning hard coded error codes, silence this
warning.
drivers/target/iscsi/iscsi_target_parameters.c:211
iscsi_create_default_params() warn: returning -1 instead of -ENOMEM is sloppy
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com> Reviewed-by: Sagi Grimberg <sagig@mellanox.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Andy Grover [Fri, 13 Nov 2015 18:42:20 +0000 (10:42 -0800)]
target/user: Do not set unused fields in tcmu_ops
TCMU sets TRANSPORT_FLAG_PASSTHROUGH, so INQUIRY commands will not be
emulated by LIO but passed up to userspace. Therefore TCMU should not
set these, just like pscsi doesn't.
Signed-off-by: Andy Grover <agrover@redhat.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Arnd Bergmann [Thu, 19 Nov 2015 12:20:54 +0000 (13:20 +0100)]
ARM: 8454/1: OF implies OF_FLATTREE
On the ARM architecture, individual platforms select CONFIG_USE_OF if they
need it, but all device tree code is keyed off CONFIG_OF. When building
a platform without DT support and manually enabling CONFIG_OF, we now
get a number of build errors, e.g.
arch/arm/kernel/devtree.c: In function 'setup_machine_fdt':
arch/arm/kernel/devtree.c:215:19: error: implicit declaration of function 'early_init_dt_verify' [-Werror=implicit-function-declaration]
We could now try to separate the use case of booting from DT vs. the
case of using the dynamic implementation, but that seems more complicated
than it can gain us.
This simply changes the ARM Kconfig file to always enable OF_RESERVED_MEM
and OF_EARLY_FLATTREE when CONFIG_OF is enabled. These options add a little
extra code when we just want the dynamic OF implementation, but that seems
like a rather obscure case, and this version solves all CONFIG_OF related
randconfig regressions.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Fixes: 0166dc11be91 ("of: make CONFIG_OF user selectable") Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Linus Torvalds [Sat, 28 Nov 2015 21:07:41 +0000 (13:07 -0800)]
Merge tag 'pci-v4.4-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
"Here are a few fixes I'd like to have in v4.4: a generic one for sysfs
and three for HiSilicon and DesignWare host controllers.
Summary:
NUMA:
- Prevent out of bounds access in numa_node override (Mathias Krause)
* tag 'pci-v4.4-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
ARM/PCI: Move align_resource function pointer to pci_host_bridge structure
PCI: hisi: Fix deferred probing
PCI: designware: Remove incorrect io_base assignment
PCI: Prevent out of bounds access in numa_node override
Linus Torvalds [Sat, 28 Nov 2015 01:22:47 +0000 (17:22 -0800)]
Merge tag 'nfs-for-4.4-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client bugfixes from Trond Myklebust:
"Highlights include:
Stable patches:
- Fix a NFSv4 callback identifier leak that was also causing client
crashes
- Fix NFSv4 callback decoding issues when incoming requests are
truncated
- Don't declare the attribute cache valid when we call
nfs_update_inode with an empty attribute structure.
- Resend LAYOUTGET when there is a race that changes the seqid
Bugfixes:
- Fix a number of issues with the NFSv4.2 CLONE ioctl()
- Properly set NFS v4.2 NFSDBG_FACILITY
- NFSv4 referrals are broken; Cleanup FATTR4_WORD0_FS_LOCATIONS after
decoding success
- Use sliding delay when LAYOUTGET gets NFS4ERR_DELAY
- Ensure that attrcache is revalidated after a SETATTR"
* tag 'nfs-for-4.4-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
nfs4: resend LAYOUTGET when there is a race that changes the seqid
nfs: if we have no valid attrs, then don't declare the attribute cache valid
nfs: ensure that attrcache is revalidated after a SETATTR
nfs4: limit callback decoding to received bytes
nfs4: start callback_ident at idr 1
nfs: use sliding delay when LAYOUTGET gets NFS4ERR_DELAY
NFS4: Cleanup FATTR4_WORD0_FS_LOCATIONS after decoding success
NFS: Properly set NFS v4.2 NFSDBG_FACILITY
nfs: reduce the amount of ifdefs for v4.2 in nfs4file.c
nfs: use btrfs ioctl defintions for clone
nfs: allow intra-file CLONE
nfs: offer native ioctls even if CONFIG_COMPAT is set
nfs: pass on count for CLONE operations
Linus Torvalds [Fri, 27 Nov 2015 23:53:23 +0000 (15:53 -0800)]
Merge git://www.linux-watchdog.org/linux-watchdog
Pull watchdog fixes from Wim Van Sebroeck:
- a null pointer dereference fix for omap_wdt
- some clock related fixes for pnx4008
- an underflow fix in wdt_set_timeout() for w83977f_wdt
- restart fix for tegra wdt
- Kconfig change to support Freescale Layerscape platforms
- fix for stopping the mtk_wdt watchdog
* git://www.linux-watchdog.org/linux-watchdog:
watchdog: mtk_wdt: Use MODE_KEY when stopping the watchdog
watchdog: Add support for Freescale Layerscape platforms
watchdog: tegra: Stop watchdog first if restarting
watchdog: w83977f_wdt: underflow in wdt_set_timeout()
watchdog: pnx4008: make global wdt_clk static
watchdog: pnx4008: fix warnings caused by enabling unprepared clock
watchdog: omap_wdt: fix null pointer dereference
Linus Torvalds [Fri, 27 Nov 2015 23:45:45 +0000 (15:45 -0800)]
Merge branch 'for-linus-4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"This has Mark Fasheh's patches to fix quota accounting during subvol
deletion, which we've been working on for a while now. The patch is
pretty small but it's a key fix.
Otherwise it's a random assortment"
* 'for-linus-4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
btrfs: fix balance range usage filters in 4.4-rc
btrfs: qgroup: account shared subtree during snapshot delete
Btrfs: use btrfs_get_fs_root in resolve_indirect_ref
btrfs: qgroup: fix quota disable during rescan
Btrfs: fix race between cleaner kthread and space cache writeout
Btrfs: fix scrub preventing unused block groups from being deleted
Btrfs: fix race between scrub and block group deletion
btrfs: fix rcu warning during device replace
btrfs: Continue replace when set_block_ro failed
btrfs: fix clashing number of the enhanced balance usage filter
Btrfs: fix the number of transaction units needed to remove a block group
Btrfs: use global reserve when deleting unused block group after ENOSPC
Btrfs: tests: checking for NULL instead of IS_ERR()
btrfs: fix signed overflows in btrfs_sync_file
Linus Torvalds [Fri, 27 Nov 2015 23:27:52 +0000 (15:27 -0800)]
Merge branch 'for-linus2' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security
Pull security layer fixes from James Morris:
"A fix for SELinux policy processing (regression introduced by
commit fa1aa143ac4a: "selinux: extended permissions for ioctls"), as
well as a fix for the user-triggerable oops in the Keys code"
* 'for-linus2' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
KEYS: Fix handling of stored error in a negatively instantiated user key
selinux: fix bug in conditional rules handling
Linus Torvalds [Fri, 27 Nov 2015 22:22:03 +0000 (14:22 -0800)]
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"There is a small backlog of at91 patches here, the most significant is
the addition of some sama5d2 Xplained nodes that were waiting on an
MFD include file to get merged through another tree.
We normally try to sort those out before the merge window opens, but
the maintainer wasn't aware of that here and I decided to merge the
changes this time as an exception.
On OMAP a series of audio changes for dra7 missed the merge window but
turned out to be necessary to fix a boot time imprecise external abort
error and to get audio working.
The other changes are the usual simple changes, here is a list sorted
by platform:
at91:
removal of a useless defconfig option
removal of some legacy DT pieces
use of the proper watchdog compatible string
update of the MAINTAINERS entries for some Atmel drivers
drivers/scpi:
hide get_scpi_ops in module from built-in code
imx:
add missing .irq_set_type for i.MX GPC irq_chip.
fix the wrong spi-num-chipselects settings for Vybrid DSPI devices.
fix a merge error in Vybrid dts regarding to ADC device property
keystone:
fix the optional PDSP firmware loading
fix linking RAM setup for QMs
fix crash with clk_ignore_unused
mediatek:
Enable SCPSYS power domain driver by default
mvebu:
fix QNAP TS219 power-off in dts
fix legacy get_irqnr_and_base for dove and orion5x
omap:
fix l4 related boot time errors for dm81xx
use lockless cldm/pwrdm api in omap4_boot_secondary
remove t410 abort handler to avoid hiding other critical errors
mark cpuidle tracepoints as _rcuidle
fix module alias for omap-ocp2scp
pxa:
palm: Fix typos in PWM lookup table code
renesas:
missing __initconst annotation for r8a7793_boards_compat_dt
rockchip:
disable mmc-tuning on the veyron-minnie board
adding the init state for the over-temperature-protection
zx:
only build power domain code when CONFIG_PM=y"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (31 commits)
ARM: OMAP4+: SMP: use lockless clkdm/pwrdm api in omap4_boot_secondary
arm: omap2+: add missing HWMOD_NO_IDLEST in 81xx hwmod data
ARM: orion5x: Fix legacy get_irqnr_and_base
ARM: dove: Fix legacy get_irqnr_and_base
soc: Mediatek: Enable SCPSYS power domain driver by default
ARM: dts: vfxxx: Fix dspi[01] spi-num-chipselects.
ARM: dts: keystone: k2l: fix kernel crash when clk_ignore_unused is not in bootargs
soc: ti: knav_qmss_queue: Fix linking RAM setup for queue managers
soc: ti: use request_firmware_direct() as acc firmware is optional
ARM: imx: add platform irq type setting in gpc
ARM: dts: vfxxx: Fix erroneous property in esdhc0 node
ARM: shmobile: r8a7793: proper constness with __initconst
scpi: hide get_scpi_ops in module from built-in code
ARM: zx: only build power domain code when CONFIG_PM=y
ARM: pxa: palm: Fix typos in PWM lookup table code
ARM: dts: Kirkwood: Fix QNAP TS219 power-off
ARM: dts: rockchip: Add OTP gpio pinctrl to rk3288 tsadc node
ARM: dts: rockchip: temporarily remove emmc hs200 speed from rk3288 minnie
MAINTAINERS: Atmel drivers: change NAND and ISI entries
ARM: at91/dt: sama5d2 Xplained: add several devices
...
Linus Torvalds [Fri, 27 Nov 2015 21:12:42 +0000 (13:12 -0800)]
Merge tag 'pm+acpi-4.4-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more power management and ACPI fixes from Rafael Wysocki:
"These fix one recent regression (cpufreq core), fix up two features
added recently (ACPI CPPC support, SCPI support in the arm_big_little
cpufreq driver) and fix three older bugs in the intel_pstate driver.
Specifics:
- Fix a recent regression in the cpufreq core causing it to fail to
clean up sysfs directories properly on cpufreq driver removal
(Viresh Kumar).
- Fix a build problem in the SCPI support code recently added to the
arm_big_little cpufreq driver (Punit Agrawal).
- Fix up the recently added CPPC cpufreq frontend to process the CPU
coordination information provided by the platform firmware
correctly (Ashwin Chaugule).
- Fix the intel_pstate driver to behave as intended when switched
over to the "performance" mode via sysfs if hardware-driven P-state
selection (HWP) is enabled (Alexandra Yates).
- Fix two rounding errors in the intel_pstate driver that sometimes
cause it to use lower P-states than requested (Prarit Bhargava)"
* tag 'pm+acpi-4.4-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
intel_pstate: Fix "performance" mode behavior with HWP enabled
cpufreq: SCPI: Depend on SCPI clk driver
cpufreq: intel_pstate: Fix limits->max_perf rounding error
cpufreq: intel_pstate: Fix limits->max_policy_pct rounding error
cpufreq: Always remove sysfs cpuX/cpufreq link on ->remove_dev()
cpufreq: CPPC: Initialize and check CPUFreq CPU co-ord type correctly
Dave Airlie [Fri, 27 Nov 2015 20:50:34 +0000 (06:50 +1000)]
Merge branch 'linux-4.4' of git://anongit.freedesktop.org/git/nouveau/linux-2.6 into drm-fixes
Ben Skeggs wrote:
A couple of regression fixes, some more boards whitelisted for a hw bug
workaround, gr/ucode fixes for hangs a user is seeing.
The changes look larger than they actually are due to the ucode binaries
(*.fucN.h) being regenerated.
* 'linux-4.4' of git://anongit.freedesktop.org/git/nouveau/linux-2.6:
drm/nouveau/volt/pwm/gk104: fix an off-by-one resulting in the voltage not being set
drm/nouveau/nvif: allow userspace access to its own client object
drm/nouveau/gr/gf100-: fix oops when calling zbc methods
drm/nouveau/gr/gf117-: assume no PPC if NV_PGRAPH_GPC_GPM_PD_PES_TPC_ID_MASK is zero
drm/nouveau/gr/gf117-: read NV_PGRAPH_GPC_GPM_PD_PES_TPC_ID_MASK from correct GPC
drm/nouveau/gr/gf100-: split out per-gpc address calculation macro
drm/nouveau/bios: return actual size of the buffer retrieved via _ROM
drm/nouveau/instmem: protect instobj list with a spinlock
drm/nouveau/pci: enable c800 magic for some unknown Samsung laptop
drm/nouveau/pci: enable c800 magic for Clevo P157SM
Linus Torvalds [Fri, 27 Nov 2015 19:59:02 +0000 (11:59 -0800)]
Merge tag 'sound-4.4-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Here are no big surprises but just all small fixes, mostly
device-specific quirks for HD-audio and USB-audio:
- Fix for detection of FireWire DICE Loud devices
- Intel Broxton HDMI/DP PCI IDs and relevant quirks
- Noise fixes: Dell XPS13 2015 model, Dell Latitude E6440, Gigabyte
Z170X mobo
- Fix the headphone mixer assignment on HP laptops for PulseAudio
- USB-MIDI fixes for Medeli DD305 and CH345
- Apply fixup for Acer Aspire One Cloudbook 14"
* tag 'sound-4.4-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Fix noise on Gigabyte Z170X mobo
ALSA: hda - Fix headphone noise after Dell XPS 13 resume back from S3
ALSA: hda - Apply HP headphone fixups more generically
ALSA: hda - Add fixup for Acer Aspire One Cloudbook 14
ALSA: hda - apply SKL display power request/release patch to BXT
ALSA: hda - add PCI IDs for Intel Broxton
ALSA: usb-audio: work around CH345 input SysEx corruption
ALSA: usb-audio: prevent CH345 multiport output SysEx corruption
ALSA: usb-audio: add packet size quirk for the Medeli DD305
ALSA: dice: fix detection of Loud devices
ALSA: hda - Fix noise on Dell Latitude E6440
Ralf Baechle [Fri, 27 Nov 2015 18:17:01 +0000 (19:17 +0100)]
MIPS: Fix delay loops which may be removed by GCC.
GCC 4.1 and newer remove empty loops. This becomes a problem when delay
loops get removed. Fixed by rewriting to user the proper Linux interface
for such delays.
Linus Torvalds [Fri, 27 Nov 2015 18:08:31 +0000 (10:08 -0800)]
Merge tag 'arc-4.4-rc3-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC fixes from Vineet Gupta:
- Fix for perf callgraph unwinding causing RCU stalls
- Fix to enable Linux to run on non-default Interrupt priority 0
- Removal of pointless SYNC from __switch_to()
* tag 'arc-4.4-rc3-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: dw2 unwind: Remove falllback linear search thru FDE entries
ARC: remove SYNC from __switch_to()
ARCv2: Use the default irq priority for idle sleep
ARC: Abstract out ISA specific SLEEP args
ARC: comments update
ARC: switch to arc-linux- CROSS_COMPILE prefix across all configs
Arnd Bergmann [Fri, 27 Nov 2015 16:41:48 +0000 (17:41 +0100)]
Merge tag 'v4.4-rockchip-dts32-fixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into fixes
Merge "ARM: rockchip: devicetree fixes for 4.4" from Heiko Stuebner:
Two fixes to Rockchip devicetree files, disabling the mmc-tuning
on the veyron-minnie board for now and adding the init state for
the over-temperature-protection to prevent glitches making the
system reboot sometimes.
* tag 'v4.4-rockchip-dts32-fixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: Add OTP gpio pinctrl to rk3288 tsadc node
ARM: dts: rockchip: temporarily remove emmc hs200 speed from rk3288 minnie
Arnd Bergmann [Fri, 27 Nov 2015 16:28:10 +0000 (17:28 +0100)]
Merge tag 'renesas-fixes-for-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes
Merge "Renesas ARM Based SoC Fixes for v4.4" from Simon Horman:
* r8a7793 SoC: Annotate r8a7793_boards_compat_dt with __initconst
Aside from being correct this builds that otherwise
fail with section mismatch errors.
* tag 'renesas-fixes-for-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: r8a7793: proper constness with __initconst
Linus Torvalds [Thu, 26 Nov 2015 19:42:25 +0000 (11:42 -0800)]
Merge tag 'for-linus-4.4-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen bug fixes from David Vrabel:
- Fix gntdev and numa balancing.
- Fix x86 boot crash due to unallocated legacy irq descs.
- Fix overflow in evtchn device when > 1024 event channels.
* tag 'for-linus-4.4-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/evtchn: dynamically grow pending event channel ring
xen/events: Always allocate legacy interrupts on PV guests
xen/gntdev: Grant maps should not be subject to NUMA balancing
Linus Torvalds [Thu, 26 Nov 2015 19:19:59 +0000 (11:19 -0800)]
Merge tag 'powerpc-4.4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- tm: Block signal return from setting invalid MSR state from Michael
Neuling
- tm: Check for already reclaimed tasks from Michael Neuling
* tag 'powerpc-4.4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/tm: Check for already reclaimed tasks
powerpc/tm: Block signal return setting invalid MSR state
David Vrabel [Thu, 26 Nov 2015 16:14:35 +0000 (16:14 +0000)]
xen/evtchn: dynamically grow pending event channel ring
If more than 1024 event channels are bound to a evtchn device then it
possible (even with well behaved applications) for the ring to
overflow and events to be lost (reported as an -EFBIG error).
Dynamically increase the size of the ring so there is always enough
space for all bound events. Well behaved applicables that only unmask
events after draining them from the ring can thus no longer lose
events.
However, an application could unmask an event before draining it,
allowing multiple entries per port to accumulate in the ring, and a
overflow could still occur. So the overflow detection and reporting
is retained.
The ring size is initially only 64 entries so the common use case of
an application only binding a few events will use less memory than
before. The ring size may grow to 512 KiB (enough for all 2^17
possible channels). This order 7 kmalloc() may fail due to memory
fragmentation, so we fall back to trying vmalloc().
Signed-off-by: David Vrabel <david.vrabel@citrix.com> Reviewed-by: Andrew Cooper <andrew.cooper3@citrix.com>
Ard Biesheuvel [Mon, 23 Nov 2015 07:43:24 +0000 (08:43 +0100)]
arm64: efi: fix initcall return values
Even though initcall return values are typically ignored, the
prototype is to return 0 on success or a negative errno value on
error. So fix the arm_enable_runtime_services() implementation to
return 0 on conditions that are not in fact errors, and return a
meaningful error code otherwise.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Reviewed-by: Matt Fleming <matt@codeblueprint.co.uk> Acked-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Ard Biesheuvel [Mon, 23 Nov 2015 07:43:23 +0000 (08:43 +0100)]
arm64: efi: deal with NULL return value of early_memremap()
Add NULL return value checks to two invocations of early_memremap()
in the UEFI init code. For the UEFI configuration tables, we just
warn since we have a better chance of being able to report the issue
in a way that can actually be noticed by a human operator if we don't
abort right away. For the UEFI memory map, however, all we can do is
panic() since we cannot proceed without a description of memory.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Reviewed-by: Matt Fleming <matt@codeblueprint.co.uk> Acked-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
projects / linux-beck.git / log