Russell King [Fri, 5 Oct 2012 12:32:08 +0000 (13:32 +0100)]
SERIAL: omap: fix hardware assisted flow control
When the UART device has hardware flow control enabled, it ignores the
MCR RTS bit in the MCR register, and keeps RTS asserted as long as we
continue to read characters from the UART receiver FIFO. This means
that when the TTY buffers become full, the UART doesn't tell the remote
end to stop sending, which causes the TTY layer to start dropping
characters.
A similar problem exists with software flow control. We need the FIFO
register to fill when software flow control is enabled to provoke the
UART to send the XOFF character.
Fix this by implementing the throttle/unthrottle callbacks, and use
these to disable receiver interrupts. This in turn means that the UART
FIFO will fill, which will then cause the UART's hardware to deassert
the RTS signal and/or send the XOFF character, stopping the remote end.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Sat, 6 Oct 2012 08:34:36 +0000 (09:34 +0100)]
SERIAL: omap: move xon/xoff setting earlier
Take advantage of the switch to mode B for accessing the TCR register,
and move the xon/xoff configuration there. This allows further
simplication of this sequence.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Sat, 6 Oct 2012 08:12:44 +0000 (09:12 +0100)]
SERIAL: omap: always set TCR
We always setup the TCR register in the software flow control path,
and when hardware flow control is enabled. Remove this redundant
setup, and place it before we setup any hardware flow control.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Sat, 6 Oct 2012 08:08:20 +0000 (09:08 +0100)]
SERIAL: omap: simplify
We have the sequence:
- LCR mode B
- write EFR with ECB clear
- LCR mode normal
- if s/w flow
- LCR mode B
- write EFR with ECB clear
...
- LCR mode B
- write EFR with ECB clear
- LCR mode normal
This can be simplified to:
- if s/w flow
- LCR mode B
- write EFR with ECB clear
...
- LCR mode B
- write EFR with ECB clear
- LCR mode normal
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Sat, 6 Oct 2012 08:04:03 +0000 (09:04 +0100)]
SERIAL: omap: don't read back LCR/MCR/EFR
There's really no reason to read back these registers while setting
the termios modes, provided we keep our cached copies up to date.
Remove these readbacks.
This has the benefit that we know that the EFR_ECB and MCR_TCRTLR
bits will always be clear, so we don't need to keep masking these
bits throughout the code.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Sat, 6 Oct 2012 09:50:58 +0000 (10:50 +0100)]
SERIAL: omap: move driver private definitions and structures to driver
struct uart_omap_port and struct uart_omap_dma, and associated
definitions are private to the driver, so there's no point them sitting
in an include file under arch/arm. Move them into the driver itself.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Mon, 15 Oct 2012 14:21:46 +0000 (15:21 +0100)]
SERIAL: omap: remove 'irq_pending' bitfield
irq_pending is never used, so let's remove it. It seems to be result
of a bad rebase of d37c6cebcb0c (serial: omap: move uart_omap_port
definition to C file)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Fri, 5 Oct 2012 12:54:53 +0000 (13:54 +0100)]
SERIAL: omap: fix MCR TCRTLR bit handling
The MCR TCRTLR bit can only be changed when ECB is set in the EFR.
Unfortunately, several places were trying to alter this bit while ECB
was clear:
- serial_omap_configure_xonxoff() was attempting to clear the bit after
explicitly clearing the ECB bit.
- serial_omap_set_termios() was trying the same trick after setting the
SCR, and when trying to change the TCR register when hardware flow
control was enabled.
Fix this by ensuring that we always have ECB set whenever the TCRTLR bit
is changed.
Moreover, we start out by reading the EFR and MCR registers, which may
have indeterminent bit settings for the ECB and TCRTLR bits. Ensure
that these bits always start off in a known state.
In order to avoid any undesired behaviour appearing through fixing this,
we also ensure that hardware assisted flow control is disabled while new
driver specific parts are not in place.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Fri, 5 Oct 2012 11:23:28 +0000 (12:23 +0100)]
SERIAL: omap: fix set_mctrl() breakage
c538d20c7f (and maybe previous commits) broke set_mctrl() by making
it only capable of setting bits in the MCR register. This prevents
software controlled flow control and modem control line manipulation
via TIOCMSET/TIOCMBIC from working correctly.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Fri, 5 Oct 2012 14:13:56 +0000 (15:13 +0100)]
SERIAL: omap: no need to re-read EFR
There's no need to re-read EFR after we've recently written it; the
register is a configuration register which doesn't change its value
without us writing to it. The last value which was written to this
register was up->efr.
Removing this re-reading avoids the possibility that we end up with
up->efr having unintended bits set, which should only be temporarily
set when accessing the enhanced features.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Fri, 5 Oct 2012 23:51:17 +0000 (00:51 +0100)]
SERIAL: omap: remove setting of EFR SCD bit
The SCD (special character detect) bit enables comparisons with XOFF2,
which we do not program. As the XOFF2 character remains unprogrammed,
there's little point enabling this feature along with its associated
interrupt. Remove this, and ensure that the SCD bit is cleared.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Fri, 5 Oct 2012 23:11:16 +0000 (00:11 +0100)]
SERIAL: omap: allow hardware assisted IXANY mode to be disabled
Nothing was clearing the UART_MCR_XONANY bit, so once the ixany
mode gets set, there's no possibility to disable it. Clear this
bit when IXANY mode is cleared.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Fri, 5 Oct 2012 22:48:28 +0000 (23:48 +0100)]
SERIAL: omap: allow hardware assisted rts/cts modes to be disabled
There is nothing which clears the auto RTS/CTS bits, so once hardware
flow control gets enabled, there's no possibility to disable it.
So, clear these bits when CRTSCTS is cleared.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Tue, 17 Apr 2012 16:23:14 +0000 (17:23 +0100)]
SERIAL: core: add throttle/unthrottle callbacks for hardware assisted flow control
Add two callbacks for hardware assisted flow control; we need to know
when the tty layers want us to stop and restart due to their buffer
levels.
Call a driver specific throttle/unthrottle function if and only if the
driver indicates that it is using an enabled hardware assisted flow
control method, otherwise fall back to the non-hardware assisted
methods.
Acked-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Tue, 17 Apr 2012 15:41:10 +0000 (16:41 +0100)]
SERIAL: core: add hardware assisted h/w flow control support
Ports which are handling h/w flow control in hardware must not have
their RTS state altered depending on the tty's hardware-stopped state.
Avoid this additional logic when setting the termios state.
Acked-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Tue, 17 Apr 2012 15:34:13 +0000 (16:34 +0100)]
SERIAL: core: add hardware assisted s/w flow control support
Ports which are capable of handling s/w flow control in hardware to
know when the s/w flow control termios settings are changed. Add a
flag to allow the low level serial drivers to indicate that they
support this, and these changes should be propagated to them.
Acked-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The variables here are really not used uninitialized.
arch/arm/mm/alignment.c: In function 'do_alignment':
arch/arm/mm/alignment.c:327:15: warning: 'offset.un' may be used uninitialized in this function [-Wmaybe-uninitialized]
arch/arm/mm/alignment.c:748:21: note: 'offset.un' was declared here
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Stephen Boyd [Mon, 29 Oct 2012 18:19:34 +0000 (19:19 +0100)]
ARM: 7568/1: Sort exception table at compile time
Add the ARM machine identifier to sortextable and select the
config option so that we can sort the exception table at compile
time. sortextable relies on a section named __ex_table existing
in the vmlinux, but ARM's linker script places the exception
table in the data section. Give the exception table its own
section so that sortextable can find it.
This allows us to skip the sorting step during boot.
Cc: David Daney <david.daney@cavium.com> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Tested-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Linus Walleij [Tue, 23 Oct 2012 07:29:48 +0000 (08:29 +0100)]
ARM: 7563/1: SMP_TWD: make setup()/stop() reentrant
It has been brought to my knowledge that the .setup()/.stop()
function pair in the SMP TWD is going to be called from atomic
contexts for CPUs coming and going, and then the
clk_prepare()/clk_unprepare() calls cannot be called
on subsequent .setup()/.stop() iterations. This is however
just the tip of an iceberg as the function pair is not
designed to be reentrant at all.
This change makes the SMP_TWD clock .setup()/.stop() pair reentrant
by splitting the .setup() function in three parts:
- One COMMON part that is executed the first time the first CPU
in the TWD cluster is initialized. This will fetch the TWD
clk for the cluster and prepare+enable it. If no clk is
available it will calibrate the rate instead.
- One part that is executed the FIRST TIME a certain CPU is
brought on-line. This initializes and sets up the clock event
for a certain CPU.
- One part that is executed on every subsequent .setup() call.
This will re-initialize the clock event. This is augmented
to call the clk_enable()/clk_disable() pair properly.
Cc: Shawn Guo <shawn.guo@linaro.org> Reported-by: Peter Chen <peter.chen@freescale.com> Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com> Tested-by: Shawn Guo <shawn.guo@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Using the 'o' memory constraint in inline assembly can result in GCC
generating invalid immediate offsets for memory access instructions with
reduced addressing capabilities (i.e. smaller than 12-bit immediate
offsets):
http://gcc.gnu.org/bugzilla/show_bug.cgi?id=54983
As there is no constraint to specify the exact addressing mode we need,
fallback to using 'Q' exclusively for halfword I/O accesses. This may
emit an additional add instruction (using an extra register) in order
to construct the address but it will always be accepted by GAS.
Reported-by: Bastian Hecht <hechtb@googlemail.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Paul Walmsley [Tue, 23 Oct 2012 19:32:59 +0000 (20:32 +0100)]
ARM: 7566/1: vfp: fix save and restore when running on pre-VFPv3 and CONFIG_VFPv3 set
After commit 846a136881b8f73c1f74250bf6acfaa309cab1f2 ("ARM: vfp: fix
saving d16-d31 vfp registers on v6+ kernels"), the OMAP 2430SDP board
started crashing during boot with omap2plus_defconfig:
[ 3.875122] mmcblk0: mmc0:e624 SD04G 3.69 GiB
[ 3.915954] mmcblk0: p1
[ 4.086639] Internal error: Oops - undefined instruction: 0 [#1] SMP ARM
[ 4.093719] Modules linked in:
[ 4.096954] CPU: 0 Not tainted (3.6.0-02232-g759e00b #570)
[ 4.103149] PC is at vfp_reload_hw+0x1c/0x44
[ 4.107666] LR is at __und_usr_fault_32+0x0/0x8
It turns out that the context save/restore fix unmasked a latent bug
in commit 5aaf254409f8d58229107b59507a8235b715a960 ("ARM: 6203/1: Make
VFPv3 usable on ARMv6"). When CONFIG_VFPv3 is set, but the kernel is
booted on a pre-VFPv3 core, the code attempts to save and restore the
d16-d31 VFP registers. These are only present on non-D16 VFPv3+, so
this results in an undefined instruction exception. The code didn't
crash before commit 846a136 because the save and restore code was
only touching d0-d15, present on all VFP.
Fix by implementing a request from Russell King to add a new HWCAP
flag that affirmatively indicates the presence of the d16-d31
registers:
and some feedback from Måns to clarify the name of the HWCAP flag.
Signed-off-by: Paul Walmsley <paul@pwsan.com> Cc: Tony Lindgren <tony@atomide.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Dave Martin <dave.martin@linaro.org> Cc: Måns Rullgård <mans.rullgard@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Felipe Balbi 2 [Tue, 23 Oct 2012 18:00:03 +0000 (19:00 +0100)]
ARM: 7565/1: sched: stop sched_clock() during suspend
The scheduler imposes a requirement to sched_clock()
which is to stop the clock during suspend, if we don't
do that any RT thread will be rescheduled in the future
which might cause any sort of problems.
This became an issue on OMAP when we converted omap-i2c.c
to use threaded IRQs, it turned out that depending on how
much time we spent on suspend, the I2C IRQ thread would
end up being rescheduled so far in the future that I2C
transfers would timeout and, because omap_hsmmc depends
on an I2C-connected device to detect if an MMC card is
inserted in the slot, our rootfs would just vanish.
arch/arm/kernel/sched_clock.c already had an optional
implementation (sched_clock_needs_suspend()) which would
handle scheduler's requirement properly, what this patch
does is simply to make that implementation non-optional.
Note that this has the side-effect that printk timings
won't reflect the actual time spent on suspend so other
methods to measure that will have to be used.
This has been tested with beagleboard XM (OMAP3630) and
pandaboard rev A3 (OMAP4430). Suspend to RAM is now working
after this patch.
Thanks to Kevin Hilman for helping out with debugging.
Acked-by: Kevin Hilman <khilman@ti.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Gregory CLEMENT [Tue, 23 Oct 2012 10:17:28 +0000 (11:17 +0100)]
ARM: 7547/2: cache-l2x0: add support for Aurora L2 cache ctrl
Aurora Cache Controller was designed to be compatible with the ARM L2
Cache Controller. It comes with some difference or improvement such
as:
- no cache id part number available through hardware (need to get it
by the DT).
- always write through mode available.
- two flavors of the controller outer cache and system cache (meaning
maintenance operations on L1 are broadcasted to the L2 and L2
performs the same operation).
- in outer cache mode, the cache maintenance operations are improved and
can be done on a range inside a page and are not limited to a cache
line.
Tested-and-Reviewed-by: Lior Amsalem <alior@marvell.com> Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by: Yehuda Yitschak <yehuday@marvell.com> Reviewed-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Linus Torvalds [Sun, 28 Oct 2012 18:14:52 +0000 (11:14 -0700)]
Merge tag 'ktest-v3.7-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-ktest
Pull ktest confusion fix from Steven Rostedt:
"With the v3.7-rc2 kernel, the network cards on my target boxes were
not being brought up.
I found that the modules for the network was not being installed.
This was due to the config CONFIG_MODULES_USE_ELF_RELA that came
before CONFIG_MODULES, and confused ktest in thinking that
CONFIG_MODULES=y was not found.
Ktest needs to test all configs and not just stop if something starts
with CONFIG_MODULES."
* tag 'ktest-v3.7-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-ktest:
ktest: Fix ktest confusion with CONFIG_MODULES_USE_ELF_RELA
Linus Torvalds [Sun, 28 Oct 2012 18:13:54 +0000 (11:13 -0700)]
Merge tag 'spi-mxs' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/misc
Pull minor spi MXS fixes from Mark Brown:
"These fixes are both pretty minor ones and are driver local."
* tag 'spi-mxs' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/misc:
spi: mxs: Terminate DMA in case of DMA timeout
spi: mxs: Assign message status after transfer finished
Linus Torvalds [Sun, 28 Oct 2012 18:12:38 +0000 (11:12 -0700)]
Merge tag 'fixes-for-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc fixes from Arnd Bergmann:
"Bug fixes for a number of ARM platforms, mostly OMAP, imx and at91.
These come a little later than I had hoped but unfortunately we had a
few of these patches cause regressions themselves and had to work out
how to deal with those in the meantime."
* tag 'fixes-for-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (38 commits)
Revert "ARM i.MX25: Fix PWM per clock lookups"
ARM: versatile: fix versatile_defconfig
ARM: mvebu: update defconfig with 3.7 changes
ARM: at91: fix at91x40 build
ARM: socfpga: Fix socfpga compilation with early_printk() enabled
ARM: SPEAr: Remove unused empty files
MAINTAINERS: Add arm-soc tree entry
ARM: dts: mxs: add the "clock-names" for gpmi-nand
ARM: ux500: Correct SDI5 address and add some format changes
ARM: ux500: Specify AMBA Primecell IDs for Nomadik I2C in DT
ARM: ux500: Fix build error relating to IRQCHIP_SKIP_SET_WAKE
ARM: at91: drop duplicated config SOC_AT91SAM9 entry
ARM: at91/i2c: change id to let i2c-at91 work
ARM: at91/i2c: change id to let i2c-gpio work
ARM: at91/dts: at91sam9g20ek_common: Fix typos in buttons labels.
ARM: at91: fix external interrupt specification in board code
ARM: at91: fix external interrupts in non-DT case
ARM: at91: at91sam9g10: fix SOC type detection
ARM: at91/tc: fix typo in the DT document
ARM: AM33XX: Fix configuration of dmtimer parent clock by dmtimer driverDate:Wed, 17 Oct 2012 13:55:55 -0500
...
Mikulas Patocka [Mon, 15 Oct 2012 21:20:17 +0000 (17:20 -0400)]
Lock splice_read and splice_write functions
Functions generic_file_splice_read and generic_file_splice_write access
the pagecache directly. For block devices these functions must be locked
so that block size is not changed while they are in progress.
This patch is an additional fix for commit b87570f5d349 ("Fix a crash
when block device is read and block size is changed at the same time")
that locked aio_read, aio_write and mmap against block size change.
Mikulas Patocka [Mon, 22 Oct 2012 23:39:16 +0000 (19:39 -0400)]
percpu-rw-semaphores: use rcu_read_lock_sched
Use rcu_read_lock_sched / rcu_read_unlock_sched / synchronize_sched
instead of rcu_read_lock / rcu_read_unlock / synchronize_rcu.
This is an optimization. The RCU-protected region is very small, so
there will be no latency problems if we disable preempt in this region.
So we use rcu_read_lock_sched / rcu_read_unlock_sched that translates
to preempt_disable / preempt_disable. It is smaller (and supposedly
faster) than preemptible rcu_read_lock / rcu_read_unlock.
Mikulas Patocka [Mon, 22 Oct 2012 23:37:47 +0000 (19:37 -0400)]
percpu-rw-semaphores: use light/heavy barriers
This patch introduces new barrier pair light_mb() and heavy_mb() for
percpu rw semaphores.
This patch fixes a bug in percpu-rw-semaphores where a barrier was
missing in percpu_up_write.
This patch improves performance on the read path of
percpu-rw-semaphores: on non-x86 cpus, there was a smp_mb() in
percpu_up_read. This patch changes it to a compiler barrier and removes
the "#if defined(X86) ..." condition.
arch/arm/mach-imx/clk-imx25.c: In function 'mx25_clocks_init':
arch/arm/mach-imx/clk-imx25.c:206:26: error: 'pwm_ipg_per' undeclared (first use in this function)
arch/arm/mach-imx/clk-imx25.c:206:26: note: each undeclared identifier is reported only once for each function it appears in
Sascha Hauer explains:
> There are several gates missing in clk-imx25.c. I have a patch which
> adds support for them and I seem to have missed that the above depends
> on it.
Arnd Bergmann [Fri, 26 Oct 2012 21:06:43 +0000 (23:06 +0200)]
ARM: versatile: fix versatile_defconfig
With the introduction of CONFIG_ARCH_MULTIPLATFORM, versatile is
no longer the default platform, so we need to enable
CONFIG_ARCH_VERSATILE explicitly in order for that to be selected
rather than the multiplatform configuration.
Thomas Petazzoni [Tue, 23 Oct 2012 08:17:49 +0000 (10:17 +0200)]
ARM: mvebu: update defconfig with 3.7 changes
The split of 370 and XP into two Kconfig options and the multiplatform
kernel support has changed a few Kconfig symbols, so let's update the
mvebu_defconfig file with the latest changes.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Fri, 26 Oct 2012 20:49:09 +0000 (22:49 +0200)]
ARM: at91: fix at91x40 build
patch 738a0fd7 "ARM: at91: fix external interrupts in non-DT case"
fixed a run-time error on some at91 platforms but did not apply
the same change to at91x40, which now doesn't build.
This changes at91x40 in the same way that the other platforms
were changed.
Pull networking fixes from David Miller:
"This is what we usually expect at this stage of the game, lots of
little things, mostly in drivers. With the occasional 'oops didn't
mean to do that' kind of regressions in the core code."
1) Uninitialized data in __ip_vs_get_timeouts(), from Arnd Bergmann
2) Reject invalid ACK sequences in Fast Open sockets, from Jerry Chu.
3) Lost error code on return from _rtl_usb_receive(), from Christian
Lamparter.
4) Fix reset resume on USB rt2x00, from Stanislaw Gruszka.
5) Release resources on error in pch_gbe driver, from Veaceslav Falico.
6) Default hop limit not set correctly in ip6_template_metrics[], fix
from Li RongQing.
7) Gianfar PTP code requests wrong kind of resource during probe, fix
from Wei Yang.
8) Fix VHOST net driver on big-endian, from Michael S Tsirkin.
9) Mallenox driver bug fixes from Jack Morgenstein, Or Gerlitz, Moni
Shoua, Dotan Barak, and Uri Habusha.
10) usbnet leaks memory on TX path, fix from Hemant Kumar.
11) Use socket state test, rather than presence of FIN bit packet, to
determine FIONREAD/SIOCINQ value. Fix from Eric Dumazet.
12) Fix cxgb4 build failure, from Vipul Pandya.
13) Provide a SYN_DATA_ACKED state to complement SYN_FASTOPEN in socket
info dumps. From Yuchung Cheng.
14) Fix leak of security path in kfree_skb_partial(). Fix from Eric
Dumazet.
15) Handle RX FIFO overflows more resiliently in pch_gbe driver, from
Veaceslav Falico.
16) Fix MAINTAINERS file pattern for networking drivers, from Jean
Delvare.
17) Add iPhone5 IDs to IPHETH driver, from Jay Purohit.
18) VLAN device type change restriction is too strict, and should not
trigger for the automatically generated vlan0 device. Fix from Jiri
Pirko.
19) Make PMTU/redirect flushing work properly again in ipv4, from
Steffen Klassert.
20) Fix memory corruptions by using kfree_rcu() in netlink_release().
From Eric Dumazet.
21) More qmi_wwan device IDs, from Bjørn Mork.
22) Fix unintentional change of SNAT/DNAT hooks in generic NAT
infrastructure, from Elison Niven.
23) Fix 3.6.x regression in xt_TEE netfilter module, from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (57 commits)
tilegx: fix some issues in the SW TSO support
qmi_wwan/cdc_ether: move Novatel 551 and E362 to qmi_wwan
net: usb: Fix memory leak on Tx data path
net/mlx4_core: Unmap UAR also in the case of error flow
net/mlx4_en: Don't use vlan tag value as an indication for vlan presence
net/mlx4_en: Fix double-release-range in tx-rings
bas_gigaset: fix pre_reset handling
vhost: fix mergeable bufs on BE hosts
gianfar_ptp: use iomem, not ioports resource tree in probe
ipv6: Set default hoplimit as zero.
NET_VENDOR_TI: make available for am33xx as well
pch_gbe: fix error handling in pch_gbe_up()
b43: Fix oops on unload when firmware not found
mwifiex: clean up scan state on error
mwifiex: return -EBUSY if specific scan request cannot be honored
brcmfmac: fix potential NULL dereference
Revert "ath9k_hw: Updated AR9003 tx gain table for 5GHz"
ath9k_htc: Add PID/VID for a Ubiquiti WiFiStation
rt2x00: usb: fix reset resume
rtlwifi: pass rx setup error code to caller
...
Linus Torvalds [Fri, 26 Oct 2012 21:59:01 +0000 (14:59 -0700)]
Merge branch 'fixes' of git://git.infradead.org/users/vkoul/slave-dma
Pull slave-dmaengine fixes from Vinod Koul:
"Three fixes for slave dmanegine.
Two are for typo omissions in sifr dmaengine driver and the last one
is for the imx driver fixing a missing unlock"
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: sirf: fix a typo in moving running dma_desc to active queue
dmaengine: sirf: fix a typo in dma_prep_interleaved
dmaengine: imx-dma: fix missing unlock on error in imxdma_xfer_desc()
Linus Torvalds [Fri, 26 Oct 2012 21:23:35 +0000 (14:23 -0700)]
Merge tag 'pm+acpi-for-3.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI fixes from Rafael J Wysocki:
- Fix for a memory leak in acpi_bind_one() from Jesper Juhl.
- Fix for an error code path memory leak in pm_genpd_attach_cpuidle()
from Jonghwan Choi.
- Fix for smp_processor_id() usage in preemptible code in powernow-k8
from Andreas Herrmann.
- Fix for a suspend-related memory leak in cpufreq stats from Xiaobing
Tu.
- Freezer fix for failure to clear PF_NOFREEZE along with PF_KTHREAD in
flush_old_exec() from Oleg Nesterov.
- acpi_processor_notify() fix from Alan Cox.
* tag 'pm+acpi-for-3.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: missing break
freezer: exec should clear PF_NOFREEZE along with PF_KTHREAD
Fix memory leak in cpufreq stats.
cpufreq / powernow-k8: Remove usage of smp_processor_id() in preemptible code
PM / Domains: Fix memory leak on error path in pm_genpd_attach_cpuidle
ACPI: Fix memory leak in acpi_bind_one()
Linus Torvalds [Fri, 26 Oct 2012 20:46:41 +0000 (13:46 -0700)]
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull infiniband fixes from Roland Dreier:
"Small batch of fixes for 3.7:
- Fix crash in error path in cxgb4
- Fix build error on 32 bits in mlx4
- Fix SR-IOV bugs in mlx4"
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
mlx4_core: Perform correct resource cleanup if mlx4_QUERY_ADAPTER() fails
mlx4_core: Remove annoying debug messages from SR-IOV flow
RDMA/cxgb4: Don't free chunk that we have failed to allocate
IB/mlx4: Synchronize cleanup of MCGs in MCG paravirtualization
IB/mlx4: Fix QP1 P_Key processing in the Primary Physical Function (PPF)
IB/mlx4: Fix build error on platforms where UL is not 64 bits
Linus Torvalds [Fri, 26 Oct 2012 17:26:36 +0000 (10:26 -0700)]
Merge tag 'usb-3.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg Kroah-Hartman:
"Here are a bunch of USB fixes for the 3.7-rc tree.
There's a lot of small USB serial driver fixes, and one larger one
(the mos7840 driver changes are mostly just moving code around to fix
problems.) Thanks to Johan Hovold for finding the problems and fixing
them all up.
Other than those, there is the usual new device ids, xhci bugfixes,
and gadget driver fixes, nothing out of the ordinary.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'usb-3.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (49 commits)
xhci: trivial: Remove assigned but unused ep_ctx.
xhci: trivial: Remove assigned but unused slot_ctx.
xhci: Fix missing break in xhci_evaluate_context_result.
xhci: Fix potential NULL ptr deref in command cancellation.
ehci: Add yet-another Lucid nohandoff pci quirk
ehci: fix Lucid nohandoff pci quirk to be more generic with BIOS versions
USB: mos7840: fix port_probe flow
USB: mos7840: fix port-data memory leak
USB: mos7840: remove invalid disconnect handling
USB: mos7840: remove NULL-urb submission
USB: qcserial: fix interface-data memory leak in error path
USB: option: fix interface-data memory leak in error path
USB: ipw: fix interface-data memory leak in error path
USB: mos7840: fix port-device leak in error path
USB: mos7840: fix urb leak at release
USB: sierra: fix port-data memory leak
USB: sierra: fix memory leak in probe error path
USB: sierra: fix memory leak in attach error path
USB: usb-wwan: fix multiple memory leaks in error paths
USB: keyspan: fix NULL-pointer dereferences and memory leaks
...
Linus Torvalds [Fri, 26 Oct 2012 17:25:31 +0000 (10:25 -0700)]
Merge tag 'staging-3.7-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver fixes from Greg Kroah-Hartman:
"Here are some staging driver fixes for your 3.7-rc tree.
Nothing major here, a number of iio driver fixups that were causing
problems, some comedi driver bugfixes, and a bunch of tidspbridge
warning squashing and other regressions fixed from the 3.6 release.
All have been in the linux-next releases for a bit.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'staging-3.7-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (32 commits)
staging: tidspbridge: delete unused mmu functions
staging: tidspbridge: ioremap physical address of the stack segment in shm
staging: tidspbridge: ioremap dsp sync addr
staging: tidspbridge: change type to __iomem for per and core addresses
staging: tidspbridge: drop const from custom mmu implementation
staging: tidspbridge: request the right irq for mmu
staging: ipack: add missing include (implicit declaration of function 'kfree')
staging: ramster: depends on NET
staging: omapdrm: fix allocation size for page addresses array
staging: zram: Fix handling of incompressible pages
Staging: android: binder: Allow using highmem for binder buffers
Staging: android: binder: Fix memory leak on thread/process exit
staging: comedi: ni_labpc: fix possible NULL deref during detach
staging: comedi: das08: fix possible NULL deref during detach
staging: comedi: amplc_pc263: fix possible NULL deref during detach
staging: comedi: amplc_pc236: fix possible NULL deref during detach
staging: comedi: amplc_pc236: fix invalid register access during detach
staging: comedi: amplc_dio200: fix possible NULL deref during detach
staging: comedi: 8255_pci: fix possible NULL deref during detach
staging: comedi: ni_daq_700: fix dio subdevice regression
...
Linus Torvalds [Fri, 26 Oct 2012 17:24:51 +0000 (10:24 -0700)]
Merge tag 'driver-core-3.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg Kroah-Hartman:
"Here are a number of firmware core fixes for 3.7, and some other minor
fixes. And some documentation updates thrown in for good measure.
All have been in the linux-next tree for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'driver-core-3.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
Documentation:Chinese translation of Documentation/arm64/memory.txt
Documentation:Chinese translation of Documentation/arm64/booting.txt
Documentation:Chinese translation of Documentation/IRQ.txt
firmware loader: document kernel direct loading
sysfs: sysfs_pathname/sysfs_add_one: Use strlcat() instead of strcat()
dynamic_debug: Remove unnecessary __used
firmware loader: sync firmware cache by async_synchronize_full_domain
firmware loader: let direct loading back on 'firmware_buf'
firmware loader: fix one reqeust_firmware race
firmware loader: cancel uncache work before caching firmware
Linus Torvalds [Fri, 26 Oct 2012 17:24:19 +0000 (10:24 -0700)]
Merge tag 'char-misc-3.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg Kroah-Hartman:
"Here are some driver fixes for 3.7. They include extcon driver fixes,
a hyper-v bugfix, and two other minor driver fixes.
All of these have been in the linux-next releases for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'char-misc-3.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
sonypi: suspend/resume callbacks should be conditionally compiled on CONFIG_PM_SLEEP
Drivers: hv: Cleanup error handling in vmbus_open()
extcon : register for cable interest by cable name
extcon: trivial: kfree missed from remove path
extcon: driver model release call not needed
extcon: MAX77693: Add platform data for MUIC device to initialize registers
extcon: max77693: Use max77693_update_reg for rmw operations
extcon: Fix kerneldoc for extcon_set_cable_state and extcon_set_cable_state_
extcon: adc-jack: Add missing MODULE_LICENSE
extcon: adc-jack: Fix checking return value of request_any_context_irq
extcon: Fix return value in extcon_register_interest()
extcon: unregister compat link on cleanup
extcon: Unregister compat class at module unload to fix oops
extcon: optimising the check_mutually_exclusive function
extcon: standard cable names definition and declaration changed
extcon-max8997: remove usage of ret in max8997_muic_handle_charger_type_detach
extcon: Remove duplicate inclusion of extcon.h header file
Linus Torvalds [Fri, 26 Oct 2012 17:05:07 +0000 (10:05 -0700)]
VFS: don't do protected {sym,hard}links by default
In commit 800179c9b8a1 ("This adds symlink and hardlink restrictions to
the Linux VFS"), the new link protections were enabled by default, in
the hope that no actual application would care, despite it being
technically against legacy UNIX (and documented POSIX) behavior.
However, it does turn out to break some applications. It's rare, and
it's unfortunate, but it's unacceptable to break existing systems, so
we'll have to default to legacy behavior.
In particular, it has broken the way AFD distributes files, see
http://www.dwd.de/AFD/
along with some legacy scripts.
Distributions can end up setting this at initrd time or in system
scripts: if you have security problems due to link attacks during your
early boot sequence, you have bigger problems than some kernel sysctl
setting. Do:
Alternatively, we may at some point introduce a kernel config option
that sets these kinds of "more secure but not traditional" behavioural
options automatically.
Reported-by: Nick Bowler <nbowler@elliptictech.com> Reported-by: Holger Kiehl <Holger.Kiehl@dwd.de> Cc: Kees Cook <keescook@chromium.org> Cc: Ingo Molnar <mingo@elte.hu> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Cc: Theodore Ts'o <tytso@mit.edu> Cc: stable@kernel.org # v3.6 Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 26 Oct 2012 17:03:22 +0000 (10:03 -0700)]
Merge tag 'sound-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Slightly a high amount of commits come from Adrian Knoth's HDSPM
driver fixes. Other than that, all small trival fixes or quirks that
are pretty driver-specific."
* tag 'sound-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ASoC: wm8994: Only enable extra BCLK cycles when required
ALSA: als3000: check for the kzalloc return value
ALSA: sound/isa/opti9xx/miro.c: eliminate possible double free
ALSA: hda - Fix silent headphone output from Toshiba P200
ALSA: hdspm - Fix coding style in CTL_ELEM macros
ALSA: hdspm - Fix typo in kcontrol element on RME MADI cards
ALSA: hdspm - Fix sync_in detection on AES/AES32
ALSA: hdspm - Fix sync_in reporting on RME MADI cards
ALSA: hdspm - Also report autosync_sample_rate on MADI and MADIface
ALSA: hdspm - Fix reported autosync_sample_rate
ALSA: hdspm - Fix sync check reporting on all RME HDSPM cards
ALSA: hdspm - Report external rate in slave mode on PCI MADI
ALSA: hdspm - Allow DDS/Varispeed to be set from userspace
ALSA: hda - add dock support for Thinkpad T430
ASoC: ux500_msp_i2s: Fix devm_* and return code merge error
ASoC: Ux500: Dispose of device nodes correctly
Linus Torvalds [Fri, 26 Oct 2012 17:01:43 +0000 (10:01 -0700)]
Merge branch 'fixes_for_linus' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping
Pull DMA-mapping revert from Marek Szyprowski:
"Due to my mistake, my previous pull request (merged as commit cff7b8ba60e3: "Merge branch 'fixes_for_linus' ..") contained a patch
which is aimed for v3.8 and lacks its dependences. This pull request
reverts it and fixes build break of ARM architecture."
* 'fixes_for_linus' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping:
Revert "ARM: dma-mapping: support debug_dma_mapping_error"
Linus Torvalds [Fri, 26 Oct 2012 16:35:46 +0000 (09:35 -0700)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"This fixes a couple of nasty page table initialization bugs which were
causing kdump regressions. A clean rearchitecturing of the code is in
the works - meanwhile these are reverts that restore the
best-known-working state of the kernel.
There's also EFI fixes and other small fixes."
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, mm: Undo incorrect revert in arch/x86/mm/init.c
x86: efi: Turn off efi_enabled after setup on mixed fw/kernel
x86, mm: Find_early_table_space based on ranges that are actually being mapped
x86, mm: Use memblock memory loop instead of e820_RAM
x86, mm: Trim memory in memblock to be page aligned
x86/irq/ioapic: Check for valid irq_cfg pointer in smp_irq_move_cleanup_interrupt
x86/efi: Fix oops caused by incorrect set_memory_uc() usage
x86-64: Fix page table accounting
Revert "x86/mm: Fix the size calculation of mapping tables"
MAINTAINERS: Add EFI git repository location
Linus Torvalds [Fri, 26 Oct 2012 16:35:00 +0000 (09:35 -0700)]
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"Most of the kernel diffstat relates to a group of Intel P6 and KNC
(Xeon-Phi Knights Corner) PMU driver fixes, neither of which is in
heavy use, so we took the fixes.
The rest is diverse smallish fixes to the tooling and kernel side."
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86: Remove unused variable in nhmex_rbox_alter_er()
perf/x86: Enable overflow on Intel KNC with a custom knc_pmu_handle_irq()
perf/x86: Remove cpuc->enable check on Intl KNC event enable/disable
perf/x86: Make Intel KNC use full 40-bit width of counters
perf/x86/uncore: Handle pci_read_config_dword() errors
perf/x86: Remove P6 cpuc->enabled check
perf/x86: Update/fix generic events on P6 PMU
perf/x86: Fix P6 FP_ASSIST event constraint
perf, cpu hotplug: Use cached value of smp_processor_id()
perf, cpu hotplug: Run CPU_STARTING notifiers with irqs disabled
x86/perf: Fix virtualization sanity check
perf test: Fix exclude_guest parse events tests
perf tools: do not flush maps on COMM for perf report
perf help: Fix --help for builtins
perf trace: Check if sample raw_data field is set
perf trace: Validate syscall id before growing syscall table
Linus Torvalds [Fri, 26 Oct 2012 16:34:04 +0000 (09:34 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"This has our series of fixes for the next rc. The biggest batch is
from Jan Schmidt, fixing up some problems in our subvolume quota code
and fixing btrfs send/receive to work with the new extended inode
refs."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: do not bug when we fail to commit the transaction
Btrfs: fix memory leak when cloning root's node
Btrfs: Use btrfs_update_inode_fallback when creating a snapshot
Btrfs: Send: preserve ownership (uid and gid) also for symlinks.
Btrfs: fix deadlock caused by the nested chunk allocation
btrfs: Return EINVAL when length to trim is less than FSB
Btrfs: fix memory leak in btrfs_quota_enable()
Btrfs: send correct rdev and mode in btrfs-send
Btrfs: extended inode refs support for send mechanism
Btrfs: Fix wrong error handling code
Fix a sign bug causing invalid memory access in the ino_paths ioctl.
Btrfs: comment for loop in tree_mod_log_insert_move
Btrfs: fix extent buffer reference for tree mod log roots
Btrfs: determine level of old roots
Btrfs: tree mod log's old roots could still be part of the tree
Btrfs: fix a tree mod logging issue for root replacement operations
Btrfs: don't put removals from push_node_left into tree mod log twice
Will Deacon [Wed, 1 Aug 2012 13:57:49 +0000 (14:57 +0100)]
ARM: mm: use bitmap operations when allocating new ASIDs
When allocating a new ASID, we must take care not to re-assign a
reserved ASID-value to a new mm. This requires us to check each
candidate ASID against those currently reserved by other cores before
assigning a new ASID to the current mm.
This patch improves the ASID allocation algorithm by using a
bitmap-based approach. Rather than iterating over the reserved ASID
array for each candidate ASID, we simply find the first zero bit,
ensuring that those indices corresponding to reserved ASIDs are set
when flushing during a rollover event.
Tested-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com>
Will Deacon [Fri, 27 Jul 2012 11:31:35 +0000 (12:31 +0100)]
ARM: mm: avoid taking ASID spinlock on fastpath
When scheduling a new mm, we take a spinlock so that we can:
1. Safely allocate a new ASID, if required
2. Update our active_asids field without worrying about parallel
updates to reserved_asids
3. Ensure that we flush our local TLB, if required
However, this has the nasty affect of serialising context-switch across
all CPUs in the system. The usual (fast) case is where the next mm has
a valid ASID for the current generation. In such a scenario, we can
avoid taking the lock and instead use atomic64_xchg to update the
active_asids variable for the current CPU. If a rollover occurs on
another CPU (which would take the lock), when copying the active_asids
into the reserved_asids another atomic64_xchg is used to replace each
active_asids with 0. The fast path can then detect this case and fall
back to spinning on the lock.
Tested-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com>
Will Deacon [Fri, 15 Jun 2012 13:47:31 +0000 (14:47 +0100)]
ARM: mm: remove IPI broadcasting on ASID rollover
ASIDs are allocated to MMU contexts based on a rolling counter. This
means that after 255 allocations we must invalidate all existing ASIDs
via an expensive IPI mechanism to synchronise all of the online CPUs and
ensure that all tasks execute with an ASID from the new generation.
This patch changes the rollover behaviour so that we rely instead on the
hardware broadcasting of the TLB invalidation to avoid the IPI calls.
This works by keeping track of the active ASID on each core, which is
then reserved in the case of a rollover so that currently scheduled
tasks can continue to run. For cores without hardware TLB broadcasting,
we keep track of pending flushes in a cpumask, so cores can flush their
local TLB before scheduling a new mm.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com> Tested-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com>
Arnd Bergmann [Fri, 26 Oct 2012 12:45:06 +0000 (14:45 +0200)]
Merge branch 'v3.7-samsung-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes
From Kukjin Kim <kgene.kim@samsung.com>:
One is spi stuff for fix the device names for the different subtypes of
the spi controller. And the other is adding missing .smp field for
exynos4-dt and fixing memory sections for exynos4210-trats board.
* 'v3.7-samsung-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: Set .smp field of machine descriptor for exynos4-dt
ARM: dts: Split memory into 4 sections for exynos4210-trats
ARM: SAMSUNG: Add naming of s3c64xx-spi devices
Chris Metcalf [Thu, 25 Oct 2012 07:25:20 +0000 (07:25 +0000)]
tilegx: fix some issues in the SW TSO support
This change correctly computes the header length and data length in
the fragments to avoid a bug where we would end up with extremely
slow performance. Also adopt use of skb_frag_size() accessor.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com> Cc: stable@vger.kernel.org [v3.6] Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Williams [Wed, 24 Oct 2012 12:10:34 +0000 (12:10 +0000)]
qmi_wwan/cdc_ether: move Novatel 551 and E362 to qmi_wwan
These devices provide QMI and ethernet functionality via a standard CDC
ethernet descriptor. But when driven by cdc_ether, the QMI
functionality is unavailable because only cdc_ether can claim the USB
interface. Thus blacklist the devices in cdc_ether and add their IDs to
qmi_wwan, which enables both QMI and ethernet simultaneously.
Signed-off-by: Dan Williams <dcbw@redhat.com> Cc: stable@vger.kernel.org Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Acked-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
Hemant Kumar [Thu, 25 Oct 2012 18:17:54 +0000 (18:17 +0000)]
net: usb: Fix memory leak on Tx data path
Driver anchors the tx urbs and defers the urb submission if
a transmit request comes when the interface is suspended.
Anchoring urb increments the urb reference count. These
deferred urbs are later accessed by calling usb_get_from_anchor()
for submission during interface resume. usb_get_from_anchor()
unanchors the urb but urb reference count remains same.
This causes the urb reference count to remain non-zero
after usb_free_urb() gets called and urb never gets freed.
Hence call usb_put_urb() after anchoring the urb to properly
balance the reference count for these deferred urbs. Also,
unanchor these deferred urbs during disconnect, to free them
up.
Signed-off-by: Hemant Kumar <hemantk@codeaurora.org> Acked-by: Oliver Neukum <oneukum@suse.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Dotan Barak [Thu, 25 Oct 2012 01:12:49 +0000 (01:12 +0000)]
net/mlx4_core: Unmap UAR also in the case of error flow
If a failure takes place during the EQ creation, we need to unmap the
UAR memory block too.
Signed-off-by: Dotan Barak <dotanb@dev.mellanox.co.il> Signed-off-by: Uri Habusha <urih@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jack Morgenstein [Thu, 25 Oct 2012 01:12:47 +0000 (01:12 +0000)]
net/mlx4_en: Fix double-release-range in tx-rings
The QP range is reserved as a single block. However, when freeing the
en resources, the tx-ring QPs are released both in mlx4_en_destroy_tx_ring
(one at a time) and in mlx4_en_free_resources (as a block release).
Fix by eliminating the one-at-a-time release in mlx4_en_destroy_tx_ring.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tilman Schmidt [Wed, 24 Oct 2012 08:44:32 +0000 (08:44 +0000)]
bas_gigaset: fix pre_reset handling
The delayed work function int_in_work() may call usb_reset_device()
and thus, indirectly, the driver's pre_reset method. Trying to
cancel the work synchronously in that situation would deadlock.
Fix by avoiding cancel_work_sync() in the pre_reset method.
If the reset was NOT initiated by int_in_work() this might cause
int_in_work() to run after the post_reset method, with urb_int_in
already resubmitted, so handle that case gracefully.
Signed-off-by: Tilman Schmidt <tilman@imap.cc> Signed-off-by: David S. Miller <davem@davemloft.net>
Steven Rostedt [Fri, 26 Oct 2012 04:10:32 +0000 (00:10 -0400)]
ktest: Fix ktest confusion with CONFIG_MODULES_USE_ELF_RELA
In order to decide if ktest should bother installing modules on the
target box, it checks if the config file has CONFIG_MODULES=y. But it
also checks if the '=y' part exists. It only will install modules if the
config exists and is set with '=y'. But as the regex that was used
tests:
/^CONFIG_MODULES(=y)?/
this will also match:
CONFIG_MODULES_USE_ELF_RELA
as the '=y' part was optional and it did not test the rest of the line.
When this happens, ktest will stop checking the rest of the configs but
it will also think that no modules are needed to be installed. What it
should do is only jump out of the loop if it actually found a
CONFIG_MODULES that is set to true.
Otherwise, ktest wont install the necessary modules needed for proper
booting of the test target.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Linus Torvalds [Fri, 26 Oct 2012 02:26:54 +0000 (19:26 -0700)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm radeon fixes from Dave Airlie:
"Just radeon fixes in this one:
- some new PCI IDs
- ATPX regression fix
- async VM regression fixes
- some module options fixes"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon: fix ATPX regression in acpi rework
drm/radeon: fix ATPX function documentation
drm/radeon: move the retry to gem_object_create
drm/radeon: move size limits to gem_object_create.
drm/radeon: use vzalloc for gart pages
drm/radeon: fix and simplify pot argument checks v3
drm/radeon: fix header size estimation in VM code
drm/radeon: remove set_page check from VM code
drm/radeon: fix si_set_page v2
drm/radeon: fix cayman_vm_set_page v2
drm/radeon: fix PFP sync in vm_flush
drm/radeon: add error output if VM CS fails on cayman
drm/radeon: give each backlight a unique id
drm/radeon: fix sparse warning
drm/radeon: add some new SI PCI ids
Linus Torvalds [Fri, 26 Oct 2012 02:26:16 +0000 (19:26 -0700)]
Merge tag 'nfs-for-3.7-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS bugfixes from Trond Myklebust:
- Fix the NFSv2/v3 kernel statd protocol, which broke due to net
namespace related changes.
- Fix a number of races in the SUNRPC TCP disconnect/reconnect code.
* tag 'nfs-for-3.7-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
LOCKD: Clear ln->nsm_clnt only when ln->nsm_users is zero
LOCKD: fix races in nsm_client_get
SUNRPC: Get rid of the xs_error_report socket callback
SUNRPC: Prevent races in xs_abort_connection()
Revert "SUNRPC: Ensure we close the socket on EPIPE errors too..."
SUNRPC: Clear the connect flag when socket state is TCP_CLOSE_WAIT
Dave Airlie [Thu, 25 Oct 2012 01:36:05 +0000 (11:36 +1000)]
Merge branch 'drm-fixes-3.7' of git://people.freedesktop.org/~agd5f/linux into drm-fixes
Alex writes:
"Fixes pull request for radeon. The main things here are
fixing a ATPX regression from the acpi rework, fixing some
fallout from the async VM work, and fixing some module options
that were broken in certain cases. Other than that, mainly
just bug fixes."
* 'drm-fixes-3.7' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: fix ATPX regression in acpi rework
drm/radeon: fix ATPX function documentation
drm/radeon: move the retry to gem_object_create
drm/radeon: move size limits to gem_object_create.
drm/radeon: use vzalloc for gart pages
drm/radeon: fix and simplify pot argument checks v3
drm/radeon: fix header size estimation in VM code
drm/radeon: remove set_page check from VM code
drm/radeon: fix si_set_page v2
drm/radeon: fix cayman_vm_set_page v2
drm/radeon: fix PFP sync in vm_flush
drm/radeon: add error output if VM CS fails on cayman
drm/radeon: give each backlight a unique id
drm/radeon: fix sparse warning
drm/radeon: add some new SI PCI ids
Linus Torvalds [Thu, 25 Oct 2012 23:05:57 +0000 (16:05 -0700)]
Merge branch 'akpm' (Andrew's fixes)
Merge misc fixes from Andrew Morton:
"18 total. 15 fixes and some updates to a device_cgroup patchset which
bring it up to date with the version which I should have merged in the
first place."
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (18 patches)
fs/compat_ioctl.c: VIDEO_SET_SPU_PALETTE missing error check
gen_init_cpio: avoid stack overflow when expanding
drivers/rtc/rtc-imxdi.c: add missing spin lock initialization
mm, numa: avoid setting zone_reclaim_mode unless a node is sufficiently distant
pidns: limit the nesting depth of pid namespaces
drivers/dma/dw_dmac: make driver's endianness configurable
mm/mmu_notifier: allocate mmu_notifier in advance
tools/testing/selftests/epoll/test_epoll.c: fix build
UAPI: fix tools/vm/page-types.c
mm/page_alloc.c:alloc_contig_range(): return early for err path
rbtree: include linux/compiler.h for definition of __always_inline
genalloc: stop crashing the system when destroying a pool
backlight: ili9320: add missing SPI dependency
device_cgroup: add proper checking when changing default behavior
device_cgroup: stop using simple_strtoul()
device_cgroup: rename deny_all to behavior
cgroup: fix invalid rcu dereference
mm: fix XFS oops due to dirty pages without buffers on s390
Jason Gerecke [Sun, 21 Oct 2012 07:38:03 +0000 (00:38 -0700)]
Input: wacom - handle split-sensor devices with internal hubs
Like our other pen-and-touch products, the Cintiq 24HD touch needs data
to be shared between its two sensors to facilitate proximity-based palm
rejection.
Unlike other tablets that report sensor data through separate interfaces
of the same USB device, the Cintiq 24HD touch has separate USB devices
that are connected to an internal USB hub.
This patch makes it possible to designate the USB VID/PID of the other
device so that the two may share data. To ensure we don't accidentally
link to a sensor from a physically separate device (if several have been
plugged in), we limit the search to siblings (i.e., devices directly
connected to the same hub).
H. Peter Anvin [Wed, 24 Oct 2012 21:11:48 +0000 (14:11 -0700)]
Makefile: Documentation for external tool should be correct
If one includes documentation for an external tool, it should be
correct. This is not:
1. Overriding the input to rngd should typically be neither
necessary nor desired. This is especially so since newer
versions of rngd support a number of different *types* of sources.
2. The default kernel-exported device is called /dev/hwrng not
/dev/hwrandom nor /dev/hw_random (both of which were used in the
past; however, kernel and udev seem to have converged on
/dev/hwrng.)
Overall it is better if the documentation for rngd is kept with rngd
rather than in a kernel Makefile.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com> Cc: David Howells <dhowells@redhat.com> Cc: Jeff Garzik <jgarzik@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Thu, 25 Oct 2012 22:59:34 +0000 (15:59 -0700)]
Merge branch 'fixes' of git://git.linaro.org/people/rmk/linux-arm
Pull ARM fixes from Russell King:
"A random collection of various fixes, mainly from Arnd and a few other
people. Not thing really stands out here."
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: drop experimental status for hotplug and Thumb2
ARM: 7560/1: SMP_TWD: use DIV_ROUND_CLOSEST() for periodic mode
ARM: 7559/1: smp: switch away from the idmap before updating init_mm.mm_count
ARM: 7556/1: perf: fix updated event period in response to PERF_EVENT_IOC_PERIOD
ARM: 7555/1: kexec: fix segment memory addresses check
ARM: warnings in arch/arm/include/asm/uaccess.h
ARM: binfmt_flat: unused variable 'persistent'
ARM: be really quiet when building with 'make -s'
ARM: pass -marm to gcc by default for both C and assembler
ARM: Xen: fix initial build problems
ARM: export default read_current_timer
ARM: Fix another build warning in arch/arm/mm/alignment.c
ARM: export set_irq_flags
ARM: kprobes: make more tests conditional
Linus Torvalds [Thu, 25 Oct 2012 22:57:48 +0000 (15:57 -0700)]
Merge branch 'fixes_for_linus' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping
Pull CMA and DMA-mapping fixes from Marek Szyprowski:
"This consists mainly of a set of one-liner fixes and cleanups for a
few minor issues identified in both Contiguous Memory Allocator code
and ARM DMA-mapping subsystem."
* 'fixes_for_linus' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping:
ARM: mm: Remove unused arm_vmregion priv field
ARM: dma-mapping: fix build warning in __dma_alloc()
ARM: dma-mapping: support debug_dma_mapping_error
mm: cma: alloc_contig_range: return early for err path
drivers: cma: Fix wrong CMA selected region size default value
drivers: dma-coherent: Fix typo in dma_mmap_from_coherent documentation
drivers: dma-contiguous: Don't redefine SZ_1M
The compat ioctl for VIDEO_SET_SPU_PALETTE was missing an error check
while converting ioctl arguments. This could lead to leaking kernel
stack contents into userspace.
Patch extracted from existing fix in grsecurity.
Signed-off-by: Kees Cook <keescook@chromium.org> Cc: David Miller <davem@davemloft.net> Cc: Brad Spengler <spender@grsecurity.net> Cc: PaX Team <pageexec@freemail.hu> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Kees Cook [Thu, 25 Oct 2012 20:38:14 +0000 (13:38 -0700)]
gen_init_cpio: avoid stack overflow when expanding
Fix possible overflow of the buffer used for expanding environment
variables when building file list.
In the extremely unlikely case of an attacker having control over the
environment variables visible to gen_init_cpio, control over the
contents of the file gen_init_cpio parses, and gen_init_cpio was built
without compiler hardening, the attacker can gain arbitrary execution
control via a stack buffer overflow.
David Rientjes [Thu, 25 Oct 2012 20:38:08 +0000 (13:38 -0700)]
mm, numa: avoid setting zone_reclaim_mode unless a node is sufficiently distant
Commit 957f822a0ab9 ("mm, numa: reclaim from all nodes within reclaim
distance") caused zone_reclaim_mode to be set for all systems where two
nodes are within RECLAIM_DISTANCE of each other. This is the opposite
of what we actually want: zone_reclaim_mode should be set if two nodes
are sufficiently distant.
Andrew Vagin [Thu, 25 Oct 2012 20:38:07 +0000 (13:38 -0700)]
pidns: limit the nesting depth of pid namespaces
'struct pid' is a "variable sized struct" - a header with an array of
upids at the end.
The size of the array depends on a level (depth) of pid namespaces. Now a
level of pidns is not limited, so 'struct pid' can be more than one page.
Looks reasonable, that it should be less than a page. MAX_PIS_NS_LEVEL is
not calculated from PAGE_SIZE, because in this case it depends on
architectures, config options and it will be reduced, if someone adds a
new fields in struct pid or struct upid.
I suggest to set MAX_PIS_NS_LEVEL = 32, because it saves ability to expand
"struct pid" and it's more than enough for all known for me use-cases.
When someone finds a reasonable use case, we can add a config option or a
sysctl parameter.
In addition it will reduce the effect of another problem, when we have
many nested namespaces and the oldest one starts dying.
zap_pid_ns_processe will be called for each namespace and find_vpid will
be called for each process in a namespace. find_vpid will be called
minimum max_level^2 / 2 times. The reason of that is that when we found a
bit in pidmap, we can't determine this pidns is top for this process or it
isn't.
vpid is a heavy operation, so a fork bomb, which create many nested
namespace, can make a system inaccessible for a long time. For example my
system becomes inaccessible for a few minutes with 4000 processes.
[akpm@linux-foundation.org: return -EINVAL in response to excessive nesting, not -ENOMEM] Signed-off-by: Andrew Vagin <avagin@openvz.org> Acked-by: Oleg Nesterov <oleg@redhat.com> Cc: Cyrill Gorcunov <gorcunov@openvz.org> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Cc: Pavel Emelyanov <xemul@parallels.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Hein Tibosch [Thu, 25 Oct 2012 20:38:05 +0000 (13:38 -0700)]
drivers/dma/dw_dmac: make driver's endianness configurable
The dw_dmac driver was originally developed for avr32 to be used with the
Synopsys DesignWare AHB DMA controller. Starting from 2.6.38, access to
the device's i/o memory was done with the little-endian readl/writel
functions(1)
This broke the driver for the avr32 platform, because it needs big
(native) endian accessors. This patch makes the endianness configurable
using 'DW_DMAC_BIG_ENDIAN_IO', which will default be true for AVR32
I submitted this patch before(2) but then waited for Andy to finish other
changes to the same module(3).
Gavin Shan [Thu, 25 Oct 2012 20:38:01 +0000 (13:38 -0700)]
mm/mmu_notifier: allocate mmu_notifier in advance
While allocating mmu_notifier with parameter GFP_KERNEL, swap would start
to work in case of tight available memory. Eventually, that would lead to
a deadlock while the swap deamon swaps anonymous pages. It was caused by
commit e0f3c3f78da29b ("mm/mmu_notifier: init notifier if necessary").
=================================
[ INFO: inconsistent lock state ]
3.7.0-rc1+ #518 Not tainted
---------------------------------
inconsistent {RECLAIM_FS-ON-W} -> {IN-RECLAIM_FS-W} usage.
kswapd0/35 [HC0[0]:SC0[0]:HE1:SE1] takes:
(&mapping->i_mmap_mutex){+.+.?.}, at: page_referenced+0x9c/0x2e0
{RECLAIM_FS-ON-W} state was registered at:
mark_held_locks+0x86/0x150
lockdep_trace_alloc+0x67/0xc0
kmem_cache_alloc_trace+0x33/0x230
do_mmu_notifier_register+0x87/0x180
mmu_notifier_register+0x13/0x20
kvm_dev_ioctl+0x428/0x510
do_vfs_ioctl+0x98/0x570
sys_ioctl+0x91/0xb0
system_call_fastpath+0x16/0x1b
irq event stamp: 825
hardirqs last enabled at (825): _raw_spin_unlock_irq+0x30/0x60
hardirqs last disabled at (824): _raw_spin_lock_irq+0x19/0x80
softirqs last enabled at (0): copy_process+0x630/0x17c0
softirqs last disabled at (0): (null)
...
Simply back out the above commit, which was a small performance
optimization.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com> Reported-by: Andrea Righi <andrea@betterlinux.com> Tested-by: Andrea Righi <andrea@betterlinux.com> Cc: Wanpeng Li <liwanp@linux.vnet.ibm.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Avi Kivity <avi@redhat.com> Cc: Hugh Dickins <hughd@google.com> Cc: Marcelo Tosatti <mtosatti@redhat.com> Cc: Xiao Guangrong <xiaoguangrong@linux.vnet.ibm.com> Cc: Sagi Grimberg <sagig@mellanox.co.il> Cc: Haggai Eran <haggaie@mellanox.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Latest Linus head run of "make selftests" in the tools directory failed
with references to undefined variables. Reference was to
'write_thread_data' which is the name of a struct that is being used, not
the variable itself. Change reference so it points to the variable.
Signed-off-by: Daniel Hazelton <dshadowwolf@gmail.com> Cc: "Paton J. Lewis" <palewis@adobe.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Howells [Thu, 25 Oct 2012 20:37:57 +0000 (13:37 -0700)]
UAPI: fix tools/vm/page-types.c
Fix tools/vm/page-types.c to use the UAPI variant of linux/kernel-page-flags.h
lest the following error appear:
In file included from page-types.c:38:0:
../../include/linux/kernel-page-flags.h:4:42: fatal error:
uapi/linux/kernel-page-flags.h: No such file or directory
Reported-by: Daniel Hazelton <dshadowwolf@gmail.com> Signed-off-by: David Howells <dhowells@redhat.com> Reviewed-by: Fengguang Wu <fengguang.wu@intel.com> Tested-by: Daniel Hazelton <dshadowwolf@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Bob Liu [Thu, 25 Oct 2012 20:37:56 +0000 (13:37 -0700)]
mm/page_alloc.c:alloc_contig_range(): return early for err path
If start_isolate_page_range() failed, unset_migratetype_isolate() has been
done inside it.
Signed-off-by: Bob Liu <lliubbo@gmail.com> Cc: Ni zhan Chen <nizhan.chen@gmail.com> Cc: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Will Deacon [Thu, 25 Oct 2012 20:37:53 +0000 (13:37 -0700)]
rbtree: include linux/compiler.h for definition of __always_inline
rb_erase_augmented() is a static function annotated with
__always_inline. This causes a compile failure when attempting to use
the rbtree implementation as a library (e.g. kvm tool):
rbtree_augmented.h:125:24: error: expected `=', `,', `;', `asm' or `__attribute__' before `void'
Include linux/compiler.h in rbtree_augmented.h so that the __always_inline
macro is resolved correctly.
Signed-off-by: Will Deacon <will.deacon@arm.com> Cc: Pekka Enberg <penberg@kernel.org> Reviewed-by: Michel Lespinasse <walken@google.com> Cc: Ingo Molnar <mingo@elte.hu> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
genalloc: stop crashing the system when destroying a pool
The genalloc code uses the bitmap API from include/linux/bitmap.h and
lib/bitmap.c, which is based on long values. Both bitmap_set from
lib/bitmap.c and bitmap_set_ll, which is the lockless version from
genalloc.c, use BITMAP_LAST_WORD_MASK to set the first bits in a long in
the bitmap.
That one uses (1 << bits) - 1, 0b111, if you are setting the first three
bits. This means that the API counts from the least significant bits
(LSB from now on) to the MSB. The LSB in the first long is bit 0, then.
The same works for the lookup functions.
The genalloc code uses longs for the bitmap, as it should. In
include/linux/genalloc.h, struct gen_pool_chunk has unsigned long
bits[0] as its last member. When allocating the struct, genalloc should
reserve enough space for the bitmap. This should be a proper number of
longs that can fit the amount of bits in the bitmap.
However, genalloc allocates an integer number of bytes that fit the
amount of bits, but may not be an integer amount of longs. 9 bytes, for
example, could be allocated for 70 bits.
This is a problem in itself if the Least Significat Bit in a long is in
the byte with the largest address, which happens in Big Endian machines.
This means genalloc is not allocating the byte in which it will try to
set or check for a bit.
This may end up in memory corruption, where genalloc will try to set the
bits it has not allocated. In fact, genalloc may not set these bits
because it may find them already set, because they were not zeroed since
they were not allocated. And that's what causes a BUG when
gen_pool_destroy is called and check for any set bits.
What really happens is that genalloc uses kmalloc_node with __GFP_ZERO
on gen_pool_add_virt. With SLAB and SLUB, this means the whole slab
will be cleared, not only the requested bytes. Since struct
gen_pool_chunk has a size that is a multiple of 8, and slab sizes are
multiples of 8, we get lucky and allocate and clear the right amount of
bytes.
Hower, this is not the case with SLOB or with older code that did memset
after allocating instead of using __GFP_ZERO.
So, a simple module as this (running 3.6.0), will cause a crash when
rmmod'ed.
module_init(foo_init);
module_exit(foo_exit);
[root@phantom-lp2 foo]# zcat /proc/config.gz | grep SLOB
CONFIG_SLOB=y
[root@phantom-lp2 foo]# insmod ./foo.ko
[root@phantom-lp2 foo]# rmmod foo
------------[ cut here ]------------
kernel BUG at lib/genalloc.c:243!
cpu 0x4: Vector: 700 (Program Check) at [c0000000bb0e7960]
pc: c0000000003cb50c: .gen_pool_destroy+0xac/0x110
lr: c0000000003cb4fc: .gen_pool_destroy+0x9c/0x110
sp: c0000000bb0e7be0
msr: 8000000000029032
current = 0xc0000000bb0e0000
paca = 0xc000000006d30e00 softe: 0 irq_happened: 0x01
pid = 13044, comm = rmmod
kernel BUG at lib/genalloc.c:243!
[c0000000bb0e7ca0] d000000004b00020 .foo_exit+0x20/0x38 [foo]
[c0000000bb0e7d20] c0000000000dff98 .SyS_delete_module+0x1a8/0x290
[c0000000bb0e7e30] c0000000000097d4 syscall_exit+0x0/0x94
--- Exception: c00 (System Call) at 000000800753d1a0
SP (fffd0b0e640) is in userspace
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com> Cc: Paul Gortmaker <paul.gortmaker@windriver.com> Cc: Benjamin Gaignard <benjamin.gaignard@stericsson.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jingoo Han [Thu, 25 Oct 2012 20:37:48 +0000 (13:37 -0700)]
backlight: ili9320: add missing SPI dependency
Add this missing SPI dependency and prevent the driver from building
without SPI, because functions of the spi driver are used in this
driver.
drivers/video/backlight/ili9320.c:51: undefined reference to `spi_sync'
Also, a prompt string for CONFIG_LCD_ILI9320 is added for explicit
selection.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Cc: Richard Purdie <rpurdie@rpsys.net> Cc: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
projects / karo-tx-linux.git / log