brcmfmac: fallback to mimo_bw_cap for older firmwares
This resulted in disabling 20MHz operation in the firmware.
Reviewed-by: Arend Van Spriel <arend@broadcom.com> Signed-off-by: Daniel Kim <dekim@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Eliad Peller [Wed, 26 Feb 2014 12:46:35 +0000 (14:46 +0200)]
mac80211: fix vif name tracing
If sdata doesn't have a valid dev (e.g. in case of monitor
vif), the vif_name field was initialized with (a length of)
some short string, but later was set to a different,
potentially larger one.
This resulted in out-of-bounds write, which usually
appeared as garbage in the trace log.
Simply trace sdata->name, as it should always have the
correct name for both cases.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Fri, 9 May 2014 07:56:53 +0000 (09:56 +0200)]
mac80211: allow VHT with peers not capable of 40MHz
There are two (related) issues with this.
One case, reported by Michal, is related to hostap: it unsets the
20/40 capability bit for stations that associate when it's in 20
MHz mode.
The other case, reported by Eyal, is that some APs like Netgear
R6300v2 and probably others based on the BCM4360 chipset can be
configured for doing VHT at 20Mhz. In this case the beacon has
a VHT IE but the HT cap indicates transmitter only support 20Mhz.
In both of these cases, we currently avoid VHT and use only HT
this means we can't use the highest rates (MCS8), so fixing this
leads to throughput improvements.
Reported-by: Michal Kazior <michal.kazior@tieto.com> Reported-by: Eyal Shapira <eyal@wizery.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Andrea Merello [Wed, 7 May 2014 15:54:46 +0000 (17:54 +0200)]
rtl8187: make CTS-to-self protection work
CTS protection was not working properly because the HW needs
RTS flag to be asserted, and it need also RTS duration field to be
filled with CTS-to-self duration.
This patch makes the driver to do this.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Andrea Merello [Wed, 7 May 2014 15:53:17 +0000 (17:53 +0200)]
rtl8180: make CTS-to-self protection work
CTS protection was not working properly because the HW still need
RTS flag to be asserted, and it need also RTS rate field to be
set with CTS-to-self rate and RTS duration field to be filled with
CTS-to-self duration.
This patch makes the driver to do this.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Wed, 7 May 2014 07:28:31 +0000 (09:28 +0200)]
ath9k: Allow platform override without EEPROM override
Add a new platform data flag "use_eeprom" that indicates that the eeprom
found on the card itself should be used instead of the one present in
the platform data.
This allows to override the MAC address of a PCI card while preserving
the eeprom data from the card itself.
The default behavior is preserved.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Avinash Patil [Wed, 7 May 2014 05:02:45 +0000 (22:02 -0700)]
mwifiex: add HT operation IE in TDLS setup confirm
This patch adds support to populate HT operatation IE in TDLS
setup confirm command. This is required for setting wider
bandwidths for TDLS operations.
Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Avinash Patil [Wed, 7 May 2014 05:02:44 +0000 (22:02 -0700)]
mwifiex: disable TDLS link upon tear down event
This patch adds code to disable TDLS link upon reception of TDLS
teardown event from peer. Teardown event can happen either
because of TDLS teardown packet from peer or internal timeout
configured during TDLS setup. Event is propogated to cfg80211
so that userspace application can take appropriate action.
Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Avinash Patil [Wed, 7 May 2014 05:02:43 +0000 (22:02 -0700)]
mwifiex: configure inactivity timeout for TDLS link
This patch adds configuration timeout for TDLS link. This is
configuered at the time of TDLS link configuration. If TDLS link
is inactive for more than timeout, FW will tear this link.
Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
In case RFKILL is in KILL position, the NIC will issue an
interrupt straight away. This interrupt won't be sent
because it is masked in the hardware.
But if our interrupt service routine is called for another
reason (SHARED_IRQ), then we'll look at the interrupt cause
and service it. This can cause bad things if we are not
ready yet.
Explicitly clean the interrupt cause register to make sure
we won't service anything before we are ready to.
Cc: <stable@vger.kernel.org> [3.14] Reported-and-tested-by: Alexander Monakov <amonakov@gmail.com> Reviewed-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
iwlwifi: mvm: fix sparse warning when _DEBUGFS isn't set
Since the declaration of iwl_mvm_fw_error_rxf_dump and
iwl_mvm_fw_error_sram_dump is under
ifdef CONFIG_IWLWIFI_DEBUGFS, do the same for their
implementation.
Publish WIPHY_FLAG_HAS_CHANNEL_SWITCH if the fw supports
newly introduced IWL_UCODE_TLV_API_CSA_FLOW.
When CSA starts, save the switching vif inside mvm and during the CSA period
configure fw with a new beacon after each beacon transmission in order to
update the csa counters.
Also, handle correctly the CSA unbind-bind flow which is triggered by mac80211
when the actual channel switch happens.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com> Reviewed-by: Luciano Coelho <luciano.coelho@intel.com> Reviewed-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Andy Spencer [Fri, 2 May 2014 06:48:13 +0000 (06:48 +0000)]
RTL8192CU: Increase max APFM_ONMAC polling count
With certain hardware combinations the poll interval is exceeded before
initialization completes.
Tested on a MacBookPro10,1 using a Sabrent USB-A11N USB adapter.
Signed-off-by: Andy Spencer <andy753421@ucla.edu> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ben Greear [Wed, 30 Apr 2014 19:02:05 +0000 (12:02 -0700)]
ath9k: Prevent divide-by-zero upon bad beacon_interval.
A similar patch fixed crashes seen on an ath9k system
when testing against a broken ath10k AP. This patch
is slightly less protective, but probably will do the
job and is less redundant.
Signed-off-by: Ben Greear <greearb@candelatech.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 24 Apr 2014 07:57:40 +0000 (09:57 +0200)]
iwlwifi: pcie: get rid of q->n_bd
This variable always tracks a constant value (256) so there's
no need to have it. Removing it simplifies code generation,
reducing the .text size (by about 240 bytes on x86-64.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Johannes Berg [Thu, 24 Apr 2014 14:31:08 +0000 (16:31 +0200)]
iwlwifi: make LED support optional
If there's no LED on the system, it doesn't make a lot of sense
to include close to 4k of LED-related code (mostly in mac80211),
so instead of forcing LED support into the kernel, don't build
iwlwifi/mac80211 LED support if there's no LED class support.
Eran Harary [Mon, 28 Apr 2014 12:22:40 +0000 (15:22 +0300)]
iwlwifi: mvm: select the MAC address according to priority
For family 8000 products, the driver should take the MAC
address from the mac_override section and only if this
section is empty it should take it from the HW section.
Signed-off-by: Eran Harary <eran.harary@intel.com> Reviewed-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Eran Harary [Tue, 25 Mar 2014 12:14:44 +0000 (14:14 +0200)]
iwlwifi: mvm: Prioritize external nvm values on top of the OTP values
Read first the nvm sections from the OTP, then read the nvm
sections from the external file and override the OTP values
(if there were any values in the OTP).
Signed-off-by: Eran Harary <eran.harary@intel.com> Reviewed-by: Dor Shaish <dor.shaish@intel.com> Reviewed-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Eran Harary [Wed, 23 Apr 2014 07:46:09 +0000 (10:46 +0300)]
iwlwifi: mvm: prevent nic to powered up at driver load
A few devices aren't allowed to be powered up at driver
load time. Add "power_up_nic_in_init" flag to iwl_cfg
structure to customize the load flow according to the
device.
Signed-off-by: Eran Harary <eran.harary@intel.com> Reviewed-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The expected throughput table used when estimating a new column
depends on the channel bandwidth. When switching from legacy to
siso or mimo the wrong expected throughput table was used as it
was chosen based on the the channel bandwidth in legacy which is
always 20Mhz. Instead it should be chosen based on the current sta
bandwidth which could be also 40Mhz or 80Mhz.
When enabling MCS9 this bug leads to a problem where the max
expected throughput of the siso or mimo column is 0 as MCS9 isn't
supported in 20Mhz. This in turns prevents switching to siso or mimo.
Fix this by using the sta bandwidth when deciding which table to choose.
iwlwifi: mvm: rs: don't allow TPC when power save is disabled
Currently we were checking only if the driver power_scheme is set
to CAM. TPC shouldn't be enabled also when disabling powersave on the
interface (e.g. iw wlan0 set power_save off)
which may occur even if power_scheme wasn't set to CAM.
rs_get_best_rate determines the optimal rate to try in a
new Tx column. Currently we were sometimes trying a too high
rate which would lead us to fail and avoid switching to the
new column despite it having a potential to be better.
Change the logic to try and find the first rate which would
exceed the current actual throughput or be more aggressive
if the success ratio is good.
iwlwifi: mvm: rs: revert changes to search cycle rules
Adding more options in the search cycle causes longer
search cycles with additional wondering off to non optimal Tx
configurations. Reduce the Tx configurations searched to
improve throughput in non optimal attenuations.
cfg80211 is notified about connection failures by
__cfg80211_connect_result() call. However, this
function currently does not free cfg80211 sme.
This results in hanging connection attempts in some cases
e.g. when mac80211 authentication attempt is denied,
we have this function call:
ieee80211_rx_mgmt_auth() -> cfg80211_rx_mlme_mgmt() ->
cfg80211_process_auth() -> cfg80211_sme_rx_auth() ->
__cfg80211_connect_result()
but cfg80211_sme_free() is never get called.
Fixes: ceca7b712 ("cfg80211: separate internal SME implementation") Cc: stable@vger.kernel.org (3.10+) Signed-off-by: Eliad Peller <eliadx.peller@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Henning Rogge [Thu, 1 May 2014 08:03:46 +0000 (10:03 +0200)]
mac80211: Fix mac80211 station info rx bitrate for IBSS mode
Filter out incoming multicast packages before applying their bitrate
to the rx bitrate station info field to prevent them from setting the
rx bitrate to the basic multicast rate.
Signed-off-by: Henning Rogge <hrogge@gmail.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Ben Hutchings [Sat, 26 Apr 2014 20:59:04 +0000 (21:59 +0100)]
rtl8192cu: Fix unbalanced irq enable in error path of rtl92cu_hw_init()
Fixes: a53268be0cb9 ('rtlwifi: rtl8192cu: Fix too long disable of IRQs') Cc: stable@vger.kernel.org Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is noting wrong with the above commit. The regression occurs because
V0 queue on RTL8192SE cards uses priority 6, not the usual 7. The fix is to
modify the rtl8192se routine that sets the correct transmit queue.
Reported-by: Alex Miller <almiller_1@yahoo.co.uk> Tested-by: Alex Miller <almiller_1@yahoo.co.uk> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Stable <stable@vger.kernel.org> [3.13+] Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath5k: Fix AR5K_PHY_TXPOWER_RATE_MAX register value setting.
I was reading ath5k power setting code and
noticed typing error in ath5k_hw_txpower function.
Invalid value was written to AR5K_PHY_TXPOWER_RATE_MAX
register.
Signed-off-by: Nikolay Ledovskikh <nledovskikh@gmail.com> Acked-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Coverity CID 986698 reports leakage of struct wlcore_platdev_data in the
probe functions of both the SPI/SDIO interfaces. The structure passed to
platform_device_add_data() is dynamically allocated and only freed in the
error paths, however, platform_device_add_data() adds a copy of the platform
specific data to the device. Move the temporary struct that is kmemdup'ed
to the stack. This issue exists since afb43e6d (wlcore: remove if_ops from
platform_data).
Signed-off-by: Christian Engelmayer <cengelma@gmx.at> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adam Lee [Thu, 24 Apr 2014 03:08:44 +0000 (11:08 +0800)]
rtlwifi: rtl8723be: disable MSI interrupts mode
94010fa0dd07e8b904e7c6b6589f15573008ab15 ("rtlwifi: add MSI interrupts
mode support") introduced MSI interrupts mode support, which seemed
safe enough with RTL8188EE and RTL8723BE as RealTek's testing results,
but some users reported their RTL8188EE modules could not connect to
any wireless network after the MSI mode was enabled by Ubuntu 14.04.
So, let's fallback to pin-based mode until rtlwifi's MSI support get
good compatibility.
94010fa0dd07e8b904e7c6b6589f15573008ab15 ("rtlwifi: add MSI interrupts
mode support") introduced MSI interrupts mode support, which seemed
safe enough with RTL8188EE and RTL8723BE as RealTek's testing results,
but some users reported their RTL8188EE modules could not connect to
any wireless network after the MSI mode was enabled by Ubuntu 14.04.
So, let's fallback to pin-based mode until rtlwifi's MSI support get
good compatibility.
Felix Fietkau [Mon, 28 Apr 2014 16:32:12 +0000 (18:32 +0200)]
ath9k: remove tid->paused flag
There are some corner cases where the driver could get stuck with a full
tid queue that is paused, leading to a software tx queue hang.
Since the tx queueing rework, pausing per-tid queues on aggregation
session setup is no longer necessary. The driver will assign sequence
numbers to buffered frames when a new session is established, in order
to get the correct starting sequence number.
mac80211 prevents new frames from entering the queue during setup.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Sun, 27 Apr 2014 14:37:39 +0000 (16:37 +0200)]
ath9k_hw: do not lower ANI setting below default on AR913x
When the amount of noise fluctuates strongly, low immunity settings
can sometimes disrupt signal detection on AR913x chips. When that
happens, no OFDM/CCK errors are reported anymore, and ANI tunes the
radio to the lowest immunity settings.
Usually rx/tx fails as well in that case.
To fix this, keep noise immunity settings at or above ANI default level,
which will keep radio parameters at or above INI values.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
cfg80211: Dynamic channel bandwidth changes in AP mode
This extends NL80211_CMD_SET_CHANNEL to allow dynamic channel bandwidth
changes in AP mode (including P2P GO) during a lifetime of the BSS. This
can be used to implement, e.g., HT 20/40 MHz co-existence rules on the
2.4 GHz band.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ieee80211_assign_chanctx() checks if local->use_chanctx is true, so
the two code block related to ieee80211_assign_chanctx() can be moved
into above if clause, emphasize that these code are executed only if
local->use_chanctx is true.
Signed-off-by: Zhao, Gang <gamerh2o@gmail.com>
[change subject] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
cfg80211: Use 5MHz bandwidth by default when checking usable channels
Current code checks if the 20MHz bandwidth is allowed for
particular channel -- if it is not, the channel is disabled.
Since we need to use 5/10 MHz channels, this code is modified in
the way that the default bandwidth to check is 5MHz. If the
maximum bandwidth allowed by the channel is smaller than 5MHz,
the channel is disabled. Otherwise the channel is used and the
flags are set according to the bandwidth allowed by the channel.
Signed-off-by: Rostislav Lisovy <rostislav.lisovy@fel.cvut.cz> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since there are frequency bands (e.g. 5.9GHz) allowing channels
with only 10 or 5 MHz bandwidth, this patch adds attributes that
allow keeping track about this information.
When channel attributes are reported to user-space, make sure to
not break old tools, i.e. if the 'split wiphy dump' is enabled,
report the extra attributes (if present) describing the bandwidth
restrictions. If the 'split wiphy dump' is not enabled,
completely omit those channels that have flags set to either
IEEE80211_CHAN_NO_10MHZ or IEEE80211_CHAN_NO_20MHZ.
Add the check for new bandwidth restriction flags in
cfg80211_chandef_usable() to comply with the restrictions.
Signed-off-by: Rostislav Lisovy <rostislav.lisovy@fel.cvut.cz> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Zhao, Gang [Mon, 21 Apr 2014 04:53:05 +0000 (12:53 +0800)]
mac80211: change return value of notifier function
Return NOTIFY_DONE if we don't care this time's notification, return
NOTIFY_OK if we successfully handled this time's notification. That's
the formal way to do it.
Signed-off-by: Zhao, Gang <gamerh2o@gmail.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Zhao, Gang [Mon, 21 Apr 2014 04:53:04 +0000 (12:53 +0800)]
cfg80211: change return value of notifier function
Return NOTIFY_DONE if we don't care this time's notification, return
NOTIFY_OK if we successfully handled this time's notification. That's
the formal way to do it.
Signed-off-by: Zhao, Gang <gamerh2o@gmail.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Zhao, Gang [Mon, 21 Apr 2014 04:53:02 +0000 (12:53 +0800)]
cfg80211: change registered device pointer name
Name "dev" is too common and ambiguous, let all the pointer name
pointing to struct cfg80211_registered_device be "rdev". This can
improve code readability and consistency(since other places have
already called it rdev).
Signed-off-by: Zhao, Gang <gamerh2o@gmail.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Marek Kwaczynski [Mon, 14 Apr 2014 09:27:21 +0000 (11:27 +0200)]
mac80211: add option to generate CCMP IVs only for mgmt frames
Some chips can encrypt managment frames in HW, but
require generated IV in the frame. Add a key flag
that allows us to achieve this.
Signed-off-by: Marek Kwaczynski <marek.kwaczynski@tieto.com>
[use BIT(0) to fill that spot, fix indentation] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Michal Kazior [Wed, 9 Apr 2014 13:29:33 +0000 (15:29 +0200)]
mac80211: compute chanctx refcount on-the-fly
It doesn't make much sense to store refcount in
the chanctx structure. One still needs to hold
chanctx_mtx to get the value safely. Besides,
refcount isn't on performance critical paths.
This will make implementing chanctx reservation
refcounting a little easier.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Michal Kazior [Wed, 9 Apr 2014 13:29:32 +0000 (15:29 +0200)]
mac80211: fix racy usage of chanctx->refcount
Channel context refcount is protected by
chanctx_mtx. Accessing the value without holding
the mutex is racy. RCU section didn't guarantee
anything here.
Theoretically ieee80211_channel_switch() could
fail to see refcount change and read "1" instead
of, e.g. "2". This means mac80211 could accept CSA
even though it shouldn't have.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Michal Kazior [Wed, 9 Apr 2014 13:29:28 +0000 (15:29 +0200)]
mac80211: improve find_chanctx() for reservations
This allows new vifs to be assigned to a chanctx
as long as chanctx's reservation chandefs (if any)
and chanctx's current chandef (implied by assigned
vifs at the time, if any) and the new vif chandef
are all compatible.
This implies it is impossible to assign a new vif
to an in-place reservation chanctx.
This gives no advantages for single-channel
hardware. It makes sense for multi-channel
hardware only.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Michal Kazior [Wed, 9 Apr 2014 13:29:27 +0000 (15:29 +0200)]
mac80211: track reserved vifs in chanctx
This can be useful. Provides a more straghtforward
way to iterate over interfaces taking part in
chanctx reservation and allows tracking chanctx
usage explicitly.
The structure is protected by local->chanctx_mtx.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Michal Kazior [Wed, 9 Apr 2014 13:29:26 +0000 (15:29 +0200)]
mac80211: track assigned vifs in chanctx
This can be useful. Provides a more straghtforward
way to iterate over interfaces bound to a given
chanctx and allows tracking chanctx usage
explicitly.
The structure is protected by local->chanctx_mtx.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Michal Kazior [Wed, 9 Apr 2014 13:29:25 +0000 (15:29 +0200)]
mac80211: add support for radar detection for reservations
Initial chanctx reservation code wasn't aware of
radar detection requirements. This is necessary
for chanctx reservations to be used for channel
switching in the future.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Michal Kazior [Wed, 9 Apr 2014 13:29:22 +0000 (15:29 +0200)]
cfg80211: allow drivers to iterate over matching combinations
The patch splits cfg80211_check_combinations()
into an iterator function and a simple iteration
user.
This makes it possible for drivers to asses how
many channels can use given iftype setup. This in
turn can be used for future
multi-interface/multi-channel channel switching.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Ilan Peer [Wed, 23 Apr 2014 06:22:58 +0000 (09:22 +0300)]
cfg80211: Fix GO Concurrent relaxation on UNII-3
At some locations, channels 149-165 are considered a single
bundle, while at some other locations, e.g., Indonesia, channels
149-161 are considered a single bundle, while channel 165 belongs
to a different bundle. This means that:
1. A station interface connection to an AP on channel 165 allows
the instantiation of a P2P GO on channels 149-165.
2. A station interface connection to an AP on channels 149-161
does NOT allow the instantiation of a P2P GO on channel 165.
Fix this.
Signed-off-by: Ilan Peer <ilan.peer@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
projects / linux-beck.git / log