Nilesh Javali [Mon, 16 Dec 2013 11:49:31 +0000 (06:49 -0500)]
[SCSI] qla4xxx: ISP8xxx: Correct retry of adapter initialization
Issue:
For ISP8xxx, adapter initialization is not retried if
qla4xxx_initialize_adapter fails.
Fix:
If qla4xxx_initialize_adapter fails, first check if failure is due to IRQs not
attached in order to skip retrial, then free the IRQs and then retry
initializing the adapter.
Signed-off-by: Nilesh Javali <nilesh.javali@qlogic.com> Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com> Reviewed-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: John Soni Jose <sony.john-n@emulex.com> Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
scsi_cmnd n io_task was not NULL when
- Link goes down while IO was happening and session is closed.
- Task for which TMF was sent.
Signed-off-by: John Soni Jose <sony.john-n@emulex.com> Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com> Reviewed-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
[SCSI] be2iscsi: Fix the session cleanup when reboot/shutdown happens
In iSCSI Boot scenario, when machine is reboot/shutdown phase
the active sessions are not closed. Driver queue cleanup is
done as part of unload and device is disabled.
Sessions are still active, iSCSI commands are issued from
session which comes to driver, as driver cleanup and device
disabled there is kernel stack dump with errors.
Fix is invoking iscsi_session_failure with ISCSI_ERR_INVALID_HOST
on all the active sessions when shutdown routine is called.
Signed-off-by: John Soni Jose <sony.john-n@emulex.com> Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com> Reviewed-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
[SCSI] be2iscsi: Fix doorbell format for EQ/CQ/RQ s per SLI spec.
The doorbel format has been updated to support additonal functionalities
of SKH-R adapter. These changes are made such that older FW also works fine.
Signed-off-by: John Soni Jose <sony.john-n@emulex.com> Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com> Reviewed-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: John Soni Jose <sony.john-n@emulex.com> Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com> Reviewed-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
[SCSI] be2iscsi: Fix handling timed out MBX completion from FW
When an MBX command timeout happens,the resources associated with
the MBX command were freed. If FW were to give the response to
host after the timeout value set by driver then driver crashes as the MBX Cmd
resources were already freed.
This patch fixes this issue by maintaing a state flag for each of
the MBX command posted/timedout/completed.
Signed-off-by: John Soni Jose <sony.john-n@emulex.com> Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com> Reviewed-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Scott Teel <scott.teel@hp.com> Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
[SCSI] hpsa: improve error messages for driver initiated commands
On encountering unexpected error conditions from driver initiated
commands, print something useful like CDB and sense data rather than
something useless like the kernel virtual address of the command buffer.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
[SCSI] hpsa: only do device rescan for certain events
Do no rescan on every events -- way too many rescans are
triggered if we don't filter the events. Limit rescans
to be triggered by the following set of events:
* controller state change
* enclosure hot plug
* physical drive state change
* logical drive state change
* redundant controller state change
* accelerated io enabled/disabled
* accelerated io configuration change
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Encryption feature requires driver to supply additional fields
for encryption enable, tweak index, and data encryption key index
in the ioaccel2 request structure.
Encryption enable flag and data encryption key index come from
raid_map data structure from raid offload command.
During ioaccel2 submission, check device structure's raid map to see if
encryption is enabled for the device. If so, call new function below.
Add function set_encrypt_ioaccel2 to set encryption flag, data encryption key
index, and calculate tweak value from request's logical block address.
Signed-off-by: Scott Teel <scott.teel@hp.com> Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Scott Teel [Tue, 18 Feb 2014 19:57:26 +0000 (13:57 -0600)]
[SCSI] hpsa: update source file copyrights
Signed-off-by: Scott Teel <scott.teel@hp.com> Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Scott Teel [Tue, 18 Feb 2014 19:57:21 +0000 (13:57 -0600)]
[SCSI] hpsa: retry certain ioaccel error cases on the RAID path
Change the handling of HP SSD Smart Path errors with status:
0x02 CHECK CONDITION
0x08 BUSY
0x18 RESERVATION CONFLICT
0x40 TASK ABORTED
So that they get retried on the RAID Path.
Signed-off-by: Scott Teel <scott.teel@hp.com> Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Scott Teel [Tue, 18 Feb 2014 19:57:05 +0000 (13:57 -0600)]
[SCSI] hpsa: rescan devices on ioaccel2 error
Allow driver to schedule a rescan whenever a request fails on the ioaccel2 path.
This eliminates the possibility of driver getting stuck in non-ioaccel mode.
IOaccel mode (HP SSD Smart Path) is disabled by driver upon error detection.
Driver relied on idea that request would be retried through normal path, and a
subsequent error would occur on that path, and be processed by controller
firmware. As part of that process, controller disables ioaccel mode and later
reinstates it, signalling driver to change modes.
In some error cases, the error will not duplicate on the standard path,
so the driver could get stuck in non-ioaccel mode.
To avoid that, we allow driver to request a rescan during the next run of the
rescan thread.
Signed-off-by: Scott Teel <scott.teel@hp.com> Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Scott Teel [Tue, 18 Feb 2014 19:57:00 +0000 (13:57 -0600)]
[SCSI] hpsa: allow user to disable accelerated i/o path
Allow SSD Smart Path for a controller to be disabled by
the user, regardless of settings in controller firmware
or array configuration.
To disable: echo 0 > /sys/class/scsi_host/host<id>/acciopath_status
To re-enable: echo 1 > /sys/class/scsi_host/host<id>/acciopath_status
To check state: cat /sys/class/scsi_host/host<id>/acciopath_status
Signed-off-by: Scott Teel <scott.teel@hp.com> Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Scott Teel [Tue, 18 Feb 2014 19:56:55 +0000 (13:56 -0600)]
[SCSI] hpsa: complete the ioaccel raidmap code
Load balance across members of a N-way mirror set, and
handle the meta-RAID levels: R10, R50, R60.
Signed-off-by: Scott Teel <scott.teel@hp.com> Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Scott Teel [Tue, 18 Feb 2014 19:56:45 +0000 (13:56 -0600)]
[SCSI] hpsa: add task management for ioaccel mode 2
Underlying firmware cannot handle task abort on accelerated path (SSD Smart Path).
Change abort requests for accelerated path commands to physical target reset.
Send reset request on normal IO path.
Signed-off-by: Scott Teel <scott.teel@hp.com> Signed-off-by: Mike Miller <michael.miller@canonical.com> Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Scott Teel [Tue, 18 Feb 2014 19:56:39 +0000 (13:56 -0600)]
[SCSI] hpsa: teach hpsa_device_reset to do either target or lun reset
Signed-off-by: Scott Teel <scott.teel@hp.com> Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Scott Teel [Tue, 18 Feb 2014 19:56:34 +0000 (13:56 -0600)]
[SCSI] hpsa: get ioaccel mode 2 i/o working
Signed-off-by: Scott Teel <scott.teel@hp.com> Signed-off-by: Joe Handzik <Joseph.T.Handzik@hp.com> Signed-off-by: Mike Miller <michael.miller@canonical.com> Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
[SCSI] hpsa: initialize controller to perform io accelerator mode 2
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com> Signed-off-by: Scott Teel <scott.teel@hp.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Mike MIller [Tue, 18 Feb 2014 19:56:20 +0000 (13:56 -0600)]
[SCSI] hpsa: get physical device handles for io accel mode 2 as well as mode 1
Signed-off-by: Mike MIller <michael.miller@canonical.com> Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
[SCSI] hpsa: do ioaccel mode 2 resource allocations
Signed-off-by: Mike Miller <michael.miller@canonical.com> Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Mike Miller <michael.miller@canonical.com> Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Scott Teel [Tue, 18 Feb 2014 19:55:59 +0000 (13:55 -0600)]
[SCSI] hpsa: complain if physical or logical aborts are not supported
Signed-off-by: Scott Teel <scott.teel@hp.com> Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Scott Teel <scott.teel@hp.com> Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
[SCSI] hpsa: do not rescan controllers known to be locked up
* Do not check event bits on locked up controllers to
see if they need to be rescanned.
* Do not initiate any device rescans on controllers
which are known to be locked up.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
[SCSI] hpsa: poll controller to detect device change event
For shared SAS configurations, hosts need to poll Smart Arrays
periodically in order to be able to detect configuration changes
such as logical drives being added or removed from remote hosts.
A register on the controller indicates when such events have
occurred, and the driver polls the register via a workqueue
and kicks off a rescan of devices if such an event is detected.
Additionally, changes to logical drive raid offload eligibility
are autodetected in this way.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com> Signed-off-by: Scott Teel <scott.teel@hp.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
[SCSI] hpsa: update raid offload status on device rescan
When rescanning for logical drives, store information about whather
raid offload is enabled for each logical drive, and update the driver's
internal record of this.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This enables sending i/o's destined for RAID logical drives
which can be serviced by a single physical disk down a different,
faster i/o path directly to physical drives for certain logical
volumes on SSDs bypassing the Smart Array RAID stack for a
performance improvement.
Signed-off-by: Matt Gates <matthew.gates@hp.com> Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com> Signed-off-by: Scott Teel <scott.teel@hp.com> Signed-off-by: Mike Miller <michael.miller@canonical.com> Signed-off-by: Don Brace <brace@beardog.cce.hp.com> Signed-off-by: Joe Handzik <joseph.t.handzik@hp.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Scott Teel [Tue, 18 Feb 2014 19:55:28 +0000 (13:55 -0600)]
[SCSI] hpsa: fix task management for mode-1 ioaccell path
For "mode 1" io accelerated commands, the command tag is in
a different location than for commands that go down the normal
RAID path, so the abort handler needs to take this into account.
Signed-off-by: Scott Teel <scott.teel@hp.com> Signed-off-by: Mike Miller <michael.miller@canonical.com> Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
[SCSI] hpsa: only allow REQ_TYPE_FS to use fast path
When commands sent down the "fast path" fail, they must be re-tried down the
normal RAID path. We do this by kicking i/o's back to the scsi mid layer with
a DID_SOFT_ERROR status, which causes them to be retried. This won't work for
SG_IO's and other non REQ_TYPE_FS i/o's which could get kicked all the way back
to the application, which may have no idea that the command needs resubmitting
and likely no way to resubmit it in such a way the that driver can recognize it
as a resubmit and send it down the normal RAID path. So we just always send
non REQ_TYPE_FS i/o's down the normal RAID path, never down the "fast path".
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Matt Gates [Tue, 18 Feb 2014 19:55:17 +0000 (13:55 -0600)]
[SCSI] hpsa: add support for 'fastpath' i/o
For certain i/o's to certain devices (unmasked physical disks) we
can bypass the RAID stack firmware and do the i/o to the device
directly and it will be faster.
Signed-off-by: Matt Gates <matthew.gates@hp.com> Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Matt Gates [Tue, 18 Feb 2014 19:55:12 +0000 (13:55 -0600)]
[SCSI] hpsa: mark last scatter gather element as the last
This is normally optional, but for SSD Smart Path support (in
subsequent patches) it is required.
Signed-off-by: Matt Gates <matthew.gates@hp.com> Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Matt Gates [Tue, 18 Feb 2014 19:55:07 +0000 (13:55 -0600)]
[SCSI] hpsa: use extended report luns command for HP SSD SmartPath
There is an extended report luns command which contains
additional information about physical devices. In particular
we need to get the physical device handle so we can use an
alternate i/o path for fast physical devices like SSDs so
we can speed up certain i/o's by bypassing the RAID stack
code in the controller firmware.
Signed-off-by: Matt Gates <matthew.gates@hp.com> Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
spin_lock_irqsave for the HBA lock is called in one function where flag
is local to that function. Another function is called from the first
function where lock has to be released using spin_unlock_irqrestore for
calling task_done of libsas. In the second function also flag is declared
and used. For calling task_done there is no need to enable the irq. So
instead of using spin_lock_irqsave and spin_unlock_irqrestore, spin_lock
and spin_unlock is used now. This also avoids passing the flags across all
the functions where HBA lock is being used. Also removed redundant code.
Reported-by: Jason Seba <jason.seba42@gmail.com> Signed-off-by: Oleg Nesterov <oleg@redhat.com> Signed-off-by: Suresh Thiagarajan <Suresh.Thiagarajan@pmcs.com> Signed-off-by: Viswas G <viswas.g@pmcs.com> Acked-by: Jack Wang <xjtuwjp@gmail.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Hannes Reinecke [Wed, 15 Jan 2014 12:30:53 +0000 (13:30 +0100)]
[SCSI] hpsa: fixup MSI-X registration
Commit 254f796b9f22b1944c64caabc356a56caaa2facd updated
the driver to use 16 MSI-X vectors, despite the fact that
older controllers would provide only 4.
This was causing MSI-X registration to drop down to INTx
mode. But as the controller support performant mode, the
initialisation will become confused and cause the machine
to stall during boot.
This patch fixes up the MSI-X registration to re-issue
the pci_enable_msix() call with the correct number of
MSI-X vectors. With that the hpsa driver continues to
works on older controllers like the P200.
Signed-off-by: Hannes Reinecke <hare@suse.de> Acked-by: Stephen M. Cameron <scameron@beardog.cce.hp.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Vaughan Cao [Thu, 9 Jan 2014 02:21:34 +0000 (10:21 +0800)]
[SCSI] iscsi: fix wrong order of opcode and itt in iscsi_handle_reject prompt
This patch makes reject messages show right value for opcode and itt, which
is converse previously.
Signed-off-by: Vaughan Cao <vaughan.cao@oracle.com> Acked-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Fixed following smatch warnings in bfa.
drivers/scsi/bfa/bfa_ioc.c:3882 bfa_sfp_show_comp() error: memcpy()
'des' too small (64 vs 248)
drivers/scsi/bfa/bfa_ioc.c:6859 bfa_flash_status_read() warn: unsigned
'status' is never less than zero.
drivers/scsi/bfa/bfa_ioc.c:6881 bfa_flash_status_read() warn: unsigned
'status' is never less than zero.
drivers/scsi/bfa/bfa_ioc.c:6917 bfa_flash_read_start() warn: unsigned
'status' is never less than zero.
drivers/scsi/bfa/bfa_ioc.c:7043 bfa_flash_raw_read() warn: unsigned
'status' is never less than zero.
Signed-off-by: Vijaya Mohan Guvva <vmohan@brocade.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Hannes Reinecke [Fri, 17 Jan 2014 15:05:38 +0000 (16:05 +0100)]
[SCSI] scsi_error: disable eh_deadline if no host_reset_handler is set
When the host template doesn't declare an eh_host_reset_handler
the eh_deadline mechanism is pointless and will set the
device to offline. So disable eh_deadline if no
eh_host_reset_handler is present.
Signed-off-by: Hannes Reinecke <hare@suse.de> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
James Bottomley [Tue, 21 Jan 2014 15:01:41 +0000 (07:01 -0800)]
[SCSI] dual scan thread bug fix
In the highly unusual case where two threads are running concurrently through
the scanning code scanning the same target, we run into the situation where
one may allocate the target while the other is still using it. In this case,
because the reap checks for STARGET_CREATED and kills the target without
reference counting, the second thread will do the wrong thing on reap.
Fix this by reference counting even creates and doing the STARGET_CREATED
check in the final put.
Tested-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Cc: stable@vger.kernel.org # delay backport for 2 months for field testing Signed-off-by: James Bottomley <JBottomley@Parallels.com>
James Bottomley [Tue, 21 Jan 2014 15:00:50 +0000 (07:00 -0800)]
[SCSI] fix our current target reap infrastructure
This patch eliminates the reap_ref and replaces it with a proper kref.
On last put of this kref, the target is removed from visibility in
sysfs. The final call to scsi_target_reap() for the device is done from
__scsi_remove_device() and only if the device was made visible. This
ensures that the target disappears as soon as the last device is gone
rather than waiting until final release of the device (which is often
too long).
Reviewed-by: Alan Stern <stern@rowland.harvard.edu> Tested-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Cc: stable@vger.kernel.org # delay backport by 2 months for field testing Signed-off-by: James Bottomley <JBottomley@Parallels.com>
James Smart [Thu, 20 Feb 2014 19:22:16 +0000 (14:22 -0500)]
[SCSI] lpfc: remove self-assignments
Report from coverity
Reported-by: Dave Jones <davej@redhat.com> Signed-off-by: James Smart <james.smart@emulex.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
[SCSI] qla2xxx: Re-sync module parameter descriptions with the code
Fix module parameter descriptions mentioning default values that no longer
match the code.
Signed-off-by: Steven J. Magnani <steve@digidescorp.com> Acked-by: Chad Dupuis <chad.dupuis@qlogic.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Dan Carpenter [Tue, 21 Jan 2014 07:00:10 +0000 (10:00 +0300)]
[SCSI] qla2xxx: fix error handling of qla2x00_mem_alloc()
qla2x00_mem_alloc() returns 1 on success and -ENOMEM on failure. On the
one hand the caller assumes non-zero is success but on the other hand
the caller also assumes that it returns an error code.
I've fixed it to return zero on success and a negative error code on
failure. This matches the documentation as well.
[jejb: checkpatch fix] Fixes: e315cd28b9ef ('[SCSI] qla2xxx: Code changes for qla data structure refactoring') Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Saurav Kashyap <saurav.kashyap@qlogic.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Dan Williams [Thu, 6 Feb 2014 20:23:15 +0000 (12:23 -0800)]
[SCSI] isci: fix needless ata reset escalations
isci is needlessly tying libata's hands by returning
SAM_STAT_CHECK_CONDITION to some ata errors. Instead, prefer
SAS_PROTO_RESPONSE to let libata (via sas_ata_task_done()) disposition
the device-to-host fis.
For example isci is triggering an HSM Violation where AHCI is showing a
simple media error for the same bus condition:
isci:
ata7.00: failed command: READ VERIFY SECTOR(S)
ata7.00: cmd 40/00:01:00:00:00/00:00:00:00:00/e0 tag 0
res 01/04:00:00:00:00/00:00:00:00:00/e0 Emask 0x3 (HSM violation)
ahci:
ata6.00: failed command: READ VERIFY SECTOR(S)
ata6.00: cmd 40/00:01:00:00:00/00:00:00:00:00/e0 tag 0
res 51/40:01:00:00:00/00:00:00:00:00/e0 Emask 0x9 (media error)
Note that the isci response matches this from sas_ata_task_done():
/* We saw a SAS error. Send a vague error. */
[..]
dev->sata_dev.fis[3] = 0x04; /* status err */
dev->sata_dev.fis[2] = ATA_ERR;
The end effect is that isci is needlessly triggering hard resets when
they are not necessary.
Reported-by: Xun Ni <xun.ni@intel.com> Tested-by: Nelson Cheng <nelson.cheng@intel.com> Acked-by: Lukasz Dorau <lukasz.dorau@intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Dan Williams [Thu, 6 Feb 2014 20:23:07 +0000 (12:23 -0800)]
[SCSI] libsas: introduce scmd_dbg() to quiet false positive "timeout" messages
libsas sometimes short circuits timeouts to force commands into error
recovery. It is misleading to log that the command timed-out in
sas_scsi_timed_out() when in fact it was just queued for error handling.
It's also redundant in the case of a true timeout as libata eh will
detect and report timeouts via it's AC_ERR_TIMEOUT facility.
Given that some environments consider "timeout" errors to be indicative
of impending device failure demote the sas_scsi_timed_out() timeout
message to be disabled by default. This parallels ata_scsi_timed_out().
[jejb: checkpatch fix] Reported-by: Xun Ni <xun.ni@intel.com> Tested-by: Nelson Cheng <nelson.cheng@intel.com> Acked-by: Lukasz Dorau <lukasz.dorau@intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Fix interpreting the wrong IOCB type for task management
functions in the response path.
- Merge the task management function handling for various adapters.
projects / linux-beck.git / log