Julia Lawall [Sat, 18 Feb 2012 18:19:29 +0000 (19:19 +0100)]
drivers/video/pxa168fb.c: use devm_ functions
The various devm_ functions allocate memory that is released when a driver
detaches. This patch uses these functions for data that is allocated in
the probe function of a platform device and is only freed in the remove
function.
By using devm_ioremap, it also removes a potential memory leak, because
there was no call to iounmap in the probe function.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr> Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
VX900 can do hardware scaling for both IGAs in contrast to previous
hardware which could do it only for IGA2. This patch ensures that
we set the parameter for IGA2 and not for IGA1. This fixes hardware
scaling on VX900 until we have the infrastructure to support it for
both IGAs.
Rob Clark [Mon, 20 Feb 2012 21:03:36 +0000 (15:03 -0600)]
OMAPDSS: HDMI: hot plug detect fix
The "OMAPDSS: HDMI: PHY burnout fix" commit switched the HDMI driver
over to using a GPIO for plug detect. Unfortunately the ->detect()
method was not also updated, causing HDMI to no longer work for the
omapdrm driver (because it would actually check if a connection was
detected before attempting to enable display).
Signed-off-by: Rob Clark <rob@ti.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Archit Taneja [Fri, 10 Feb 2012 06:15:52 +0000 (11:45 +0530)]
OMAPDSS: HACK: Ensure DSS clock domain gets out of idle when HDMI is enabled
For DSS clock domain to transition from idle to active state. It's necessary
to enable the optional clock DSS_FCLK before we enable the module using the
MODULEMODE bits in the clock domain's CM_DSS_DSS_CLKCTRL register.
This sequence was not followed correctly for the 'dss_hdmi' hwmod and it led
to DSS clock domain not getting out of idle when pm_runtime_get_sync() was
called for hdmi's platform device.
Since the clock domain failed to change it's state to active, the hwmod code
disables any clocks it had enabled before for this hwmod. This led to the clock
'dss_48mhz_clk' gettind disabled.
When hdmi's runtime_resume() op is called, the call to dss_runtime_get()
correctly enables the DSS clock domain this time. However, the clock
'dss_48mhz_clk' is needed for HDMI's PHY to function correctly. Since it was
disabled previously, the driver fails when it tries to enable HDMI's PHY.
Fix this for now by ensuring that dss_runtime_get() is called before we call
pm_runtime_get_sync() for hdmi's platform device. A correct fix for later would
be to modify the DSS related hwmod's mainclks, and also some changes in how
opt clocks are handled in the DSS driver.
This fixes the issue of HDMI not working when it's the default display. The
issue is not seen if any other display is already enabled as the first display
would have correctly enabled the DSS clockdomain.
Signed-off-by: Archit Taneja <archit@ti.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Linus Torvalds [Sat, 18 Feb 2012 23:40:00 +0000 (15:40 -0800)]
Merge tag 'fixes-3.3-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
These are the bug fixes that have accumulated since 3.3-rc3 in arm-soc.
The majority of them are regression fixes for stuff that broke during
the merge 3.3 window.
The notable ones are:
* The at91 ata drivers both broke because of an earlier cleanup patch that
some other patches were based on. Jean-Christophe decided to remove
the legacy at91_ide driver and fix the new-style at91-pata driver while
keeping the cleanup patch. I almost rejected the patches for being too
late and too big but in the end decided to accept them because they
fix a regression.
* A patch fixing build breakage from the sysdev-to-device conversion
colliding with other changes touches a number of mach-s3c files.
* b0654037 "ARM: orion: Fix Orion5x GPIO regression from MPP cleanup"
is a mechanical change that unfortunately touches a lot of lines
that should up in the diffstat.
* tag 'fixes-3.3-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (28 commits)
ARM: at91: drop ide driver in favor of the pata one
pata/at91: use newly introduced SMC accessors
ARM: at91: add accessor to manage SMC
ARM: at91:rtc/rtc-at91sam9: ioremap register bank
ARM: at91: USB AT91 gadget registration for module
ep93xx: fix build of vision_ep93xx.c
ARM: OMAP2xxx: PM: fix OMAP2xxx-specific UART idle bug in v3.3
ARM: orion: Fix USB phy for orion5x.
ARM: orion: Fix Orion5x GPIO regression from MPP cleanup
ARM: EXYNOS: Add cpu-offset property in gic device tree node
ARM: EXYNOS: Bring exynos4-dt up to date
ARM: OMAP3: cm-t35: fix section mismatch warning
ARM: OMAP2: Fix the OMAP2 only build break seen with 2011+ ARM tool-chains
ARM: tegra: paz00: fix wrong UART port on mini-pcie plug
ARM: tegra: paz00: fix wrong SD1 power gpio
i2c: tegra: Add devexit_p() for remove
ARM: EXYNOS: Correct M-5MOLS sensor clock frequency on Universal C210 board
ARM: EXYNOS: Correct framebuffer window size on Nuri board
ARM: SAMSUNG: Fix missing api-change from subsys_interface change
ARM: EXYNOS: Fix "warning: initialization from incompatible pointer type"
...
1) VETH_INFO_PEER netlink attribute needs to have it's size validated,
from Thomas Graf.
2) 'poll' module option of bnx2x driver crashes the machine, just remove
it. From Michal Schmidt.
3) ks8851_mll driver reads the irq number from two places, but only
initializes one of them, oops. Use only one location and fix this
problem, from Jan Weitzel.
4) Fix buffer overrun and unicast sterring bugs in mellanox mlx4 driver,
from Eugenia Emantayev.
5) Swapped kcalloc() args in RxRPC and mlx4, from Axel Lin.
6) PHY MDIO device name regression fixes from Florian Fainelli.
7) If the wake event IRQ line is different from the netdevice one, we
have to properly route it to the stmmac interrupt handler. From
Francesco Virlinzi.
8) Fix rwlock lock initialization ordering bug in mac80211, from
Mohammed Shafi Shajakhan.
9) TCP lost_cnt can get out of sync, and in fact go negative, in certain
circumstances. Fix the way we specify what sequence range to operate
on in tcp_sacktag_one() to fix this bug. From Neal Cardwell.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (27 commits)
net/ethernet: ks8851_mll fix irq handling
veth: Enforce minimum size of VETH_INFO_PEER
stmmac: update the driver version to Feb 2012 (v2)
stmmac: move hw init in the probe (v2)
stmmac: request_irq when use an ext wake irq line (v2)
stmmac: do not discard frame on dribbling bit assert
ipheth: Add iPhone 4S
mlx4: add unicast steering entries to resource_tracker
mlx4: fix QP tree trashing
mlx4: fix buffer overrun
3c59x: shorten timer period for slave devices
netpoll: netpoll_poll_dev() should access dev->flags
RxRPC: Fix kcalloc parameters swapped
bnx2x: remove the 'poll' module option
tcp: fix tcp_shifted_skb() adjustment of lost_cnt_hint for FACK
ks8851: Fix NOHZ local_softirq_pending 08 warning
bnx2x: fix bnx2x_storm_stats_update() on big endian
ixp4xx-eth: fix PHY name to match MDIO bus name
octeon: fix PHY name to match MDIO bus name
fec: fix PHY name to match fixed MDIO bus name
...
Linus Torvalds [Sat, 18 Feb 2012 23:37:25 +0000 (15:37 -0800)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Fixes a bootstrapping issue for some registers when a less commonly used
method for register cache initialisation is used. Only affects a fairly
small proportion of users that both don't use explicit register defaults
and do use the cache.
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: Fix cache defaults initialization from raw cache defaults
Linus Torvalds [Sat, 18 Feb 2012 23:28:56 +0000 (15:28 -0800)]
Merge tag 'ecryptfs-3.3-rc4-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs
Fixes maximum filename length and filesystem type reporting in statfs() calls
and also fixes stale inode mode bits on eCryptfs inodes after a POSIX ACL was
set on the lower filesystem's inode.
* tag 'ecryptfs-3.3-rc4-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs:
ecryptfs: remove the second argument of k[un]map_atomic()
eCryptfs: Copy up lower inode attrs after setting lower xattr
eCryptfs: Improve statfs reporting
Linus Torvalds [Sat, 18 Feb 2012 23:26:37 +0000 (15:26 -0800)]
Merge branch 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
Here are a few more fixes for powerpc. Some are regressions, the rest
is simple/obvious/nasty enough that I deemed it good to go now.
Here's also step one of deprecating legacy iSeries support: we are
removing it from the main defconfig.
Nobody seems to be using it anymore and the code is nasty to maintain,
(involves horrible hacks in various low level areas of the kernel) so we
plan to actually rip it out at some point. For now let's just avoid
building it by default. Stephen will proceed to do the actual removal
later (probably 3.4 or 3.5).
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/perf: power_pmu_start restores incorrect values, breaking frequency events
powerpc/adb: Use set_current_state()
powerpc: Disable interrupts early in Program Check
powerpc: Remove legacy iSeries from ppc64_defconfig
powerpc/fsl/pci: Fix PCIe fixup regression
powerpc: Fix kernel log of oops/panic instruction dump
Linus Torvalds [Sat, 18 Feb 2012 23:26:11 +0000 (15:26 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci
One regression fix for SR-IOV on PPC and a couple of misc fixes from
Yinghai.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci:
PCI: Fix pci cardbus removal
PCI: set pci sriov page size before reading SRIOV BAR
PCI: workaround hard-wired bus number V2
Linus Torvalds [Sat, 18 Feb 2012 23:25:39 +0000 (15:25 -0800)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
3 radeon fixes, I have some exynos fixes to push later but I'll queue
them separately once I've looked them over a bit.
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon/kms: fix MSI re-arm on rv370+
drm/radeon/kms/atom: bios scratch reg handling updates
drm/radeon/kms: drop lock in return path of radeon_fence_count_emitted.
Linus Torvalds [Sat, 18 Feb 2012 20:56:35 +0000 (12:56 -0800)]
i387: re-introduce FPU state preloading at context switch time
After all the FPU state cleanups and finally finding the problem that
caused all our FPU save/restore problems, this re-introduces the
preloading of FPU state that was removed in commit b3b0870ef3ff ("i387:
do not preload FPU state at task switch time").
However, instead of simply reverting the removal, this reimplements
preloading with several fixes, most notably
- properly abstracted as a true FPU state switch, rather than as
open-coded save and restore with various hacks.
In particular, implementing it as a proper FPU state switch allows us
to optimize the CR0.TS flag accesses: there is no reason to set the
TS bit only to then almost immediately clear it again. CR0 accesses
are quite slow and expensive, don't flip the bit back and forth for
no good reason.
- Make sure that the same model works for both x86-32 and x86-64, so
that there are no gratuitous differences between the two due to the
way they save and restore segment state differently due to
architectural differences that really don't matter to the FPU state.
- Avoid exposing the "preload" state to the context switch routines,
and in particular allow the concept of lazy state restore: if nothing
else has used the FPU in the meantime, and the process is still on
the same CPU, we can avoid restoring state from memory entirely, just
re-expose the state that is still in the FPU unit.
That optimized lazy restore isn't actually implemented here, but the
infrastructure is set up for it. Of course, older CPU's that use
'fnsave' to save the state cannot take advantage of this, since the
state saving also trashes the state.
In other words, there is now an actual _design_ to the FPU state saving,
rather than just random historical baggage. Hopefully it's easier to
follow as a result.
Linus Torvalds [Sat, 18 Feb 2012 05:48:54 +0000 (21:48 -0800)]
i387: move TS_USEDFPU flag from thread_info to task_struct
This moves the bit that indicates whether a thread has ownership of the
FPU from the TS_USEDFPU bit in thread_info->status to a word of its own
(called 'has_fpu') in task_struct->thread.has_fpu.
This fixes two independent bugs at the same time:
- changing 'thread_info->status' from the scheduler causes nasty
problems for the other users of that variable, since it is defined to
be thread-synchronous (that's what the "TS_" part of the naming was
supposed to indicate).
So perfectly valid code could (and did) do
ti->status |= TS_RESTORE_SIGMASK;
and the compiler was free to do that as separate load, or and store
instructions. Which can cause problems with preemption, since a task
switch could happen in between, and change the TS_USEDFPU bit. The
change to TS_USEDFPU would be overwritten by the final store.
In practice, this seldom happened, though, because the 'status' field
was seldom used more than once, so gcc would generally tend to
generate code that used a read-modify-write instruction and thus
happened to avoid this problem - RMW instructions are naturally low
fat and preemption-safe.
- On x86-32, the current_thread_info() pointer would, during interrupts
and softirqs, point to a *copy* of the real thread_info, because
x86-32 uses %esp to calculate the thread_info address, and thus the
separate irq (and softirq) stacks would cause these kinds of odd
thread_info copy aliases.
This is normally not a problem, since interrupts aren't supposed to
look at thread information anyway (what thread is running at
interrupt time really isn't very well-defined), but it confused the
heck out of irq_fpu_usable() and the code that tried to squirrel
away the FPU state.
(It also caused untold confusion for us poor kernel developers).
It also turns out that using 'task_struct' is actually much more natural
for most of the call sites that care about the FPU state, since they
tend to work with the task struct for other reasons anyway (ie
scheduling). And the FPU data that we are going to save/restore is
found there too.
Thanks to Arjan Van De Ven <arjan@linux.intel.com> for pointing us to
the %esp issue.
Cc: Arjan van de Ven <arjan@linux.intel.com> Reported-and-tested-by: Raphael Prevost <raphael@buro.asia> Acked-and-tested-by: Suresh Siddha <suresh.b.siddha@intel.com> Tested-by: Peter Anvin <hpa@zytor.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 17 Feb 2012 03:11:15 +0000 (19:11 -0800)]
i387: move AMD K7/K8 fpu fxsave/fxrstor workaround from save to restore
The AMD K7/K8 CPUs don't save/restore FDP/FIP/FOP unless an exception is
pending. In order to not leak FIP state from one process to another, we
need to do a floating point load after the fxsave of the old process,
and before the fxrstor of the new FPU state. That resets the state to
the (uninteresting) kernel load, rather than some potentially sensitive
user information.
We used to do this directly after the FPU state save, but that is
actually very inconvenient, since it
(a) corrupts what is potentially perfectly good FPU state that we might
want to lazy avoid restoring later and
(b) on x86-64 it resulted in a very annoying ordering constraint, where
"__unlazy_fpu()" in the task switch needs to be delayed until after
the DS segment has been reloaded just to get the new DS value.
Coupling it to the fxrstor instead of the fxsave automatically avoids
both of these issues, and also ensures that we only do it when actually
necessary (the FP state after a save may never actually get used). It's
simply a much more natural place for the leaked state cleanup.
Linus Torvalds [Thu, 16 Feb 2012 23:45:23 +0000 (15:45 -0800)]
i387: do not preload FPU state at task switch time
Yes, taking the trap to re-load the FPU/MMX state is expensive, but so
is spending several days looking for a bug in the state save/restore
code. And the preload code has some rather subtle interactions with
both paravirtualization support and segment state restore, so it's not
nearly as simple as it should be.
Also, now that we no longer necessarily depend on a single bit (ie
TS_USEDFPU) for keeping track of the state of the FPU, we migth be able
to do better. If we are really switching between two processes that
keep touching the FP state, save/restore is inevitable, but in the case
of having one process that does most of the FPU usage, we may actually
be able to do much better than the preloading.
In particular, we may be able to keep track of which CPU the process ran
on last, and also per CPU keep track of which process' FP state that CPU
has. For modern CPU's that don't destroy the FPU contents on save time,
that would allow us to do a lazy restore by just re-enabling the
existing FPU state - with no restore cost at all!
Tyler Hicks [Tue, 7 Feb 2012 23:55:40 +0000 (17:55 -0600)]
eCryptfs: Copy up lower inode attrs after setting lower xattr
After passing through a ->setxattr() call, eCryptfs needs to copy the
inode attributes from the lower inode to the eCryptfs inode, as they
may have changed in the lower filesystem's ->setxattr() path.
One example is if an extended attribute containing a POSIX Access
Control List is being set. The new ACL may cause the lower filesystem to
modify the mode of the lower inode and the eCryptfs inode would need to
be updated to reflect the new mode.
Tyler Hicks [Sat, 5 Nov 2011 17:45:08 +0000 (13:45 -0400)]
eCryptfs: Improve statfs reporting
statfs() calls on eCryptfs files returned the wrong filesystem type and,
when using filename encryption, the wrong maximum filename length.
If mount-wide filename encryption is enabled, the cipher block size and
the lower filesystem's max filename length will determine the max
eCryptfs filename length. Pre-tested, known good lengths are used when
the lower filesystem's namelen is 255 and a cipher with 8 or 16 byte
block sizes is used. In other, less common cases, we fall back to a safe
rounded-down estimate when determining the eCryptfs namelen.
Linus Torvalds [Thu, 16 Feb 2012 21:33:12 +0000 (13:33 -0800)]
i387: don't ever touch TS_USEDFPU directly, use helper functions
This creates three helper functions that do the TS_USEDFPU accesses, and
makes everybody that used to do it by hand use those helpers instead.
In addition, there's a couple of helper functions for the "change both
CR0.TS and TS_USEDFPU at the same time" case, and the places that do
that together have been changed to use those. That means that we have
fewer random places that open-code this situation.
The intent is partly to clarify the code without actually changing any
semantics yet (since we clearly still have some hard to reproduce bug in
this area), but also to make it much easier to use another approach
entirely to caching the CR0.TS bit for software accesses.
Right now we use a bit in the thread-info 'status' variable (this patch
does not change that), but we might want to make it a full field of its
own or even make it a per-cpu variable.
Linus Torvalds [Thu, 16 Feb 2012 20:22:48 +0000 (12:22 -0800)]
i387: move TS_USEDFPU clearing out of __save_init_fpu and into callers
Touching TS_USEDFPU without touching CR0.TS is confusing, so don't do
it. By moving it into the callers, we always do the TS_USEDFPU next to
the CR0.TS accesses in the source code, and it's much easier to see how
the two go hand in hand.
Linus Torvalds [Thu, 16 Feb 2012 17:15:04 +0000 (09:15 -0800)]
i387: fix x86-64 preemption-unsafe user stack save/restore
Commit 5b1cbac37798 ("i387: make irq_fpu_usable() tests more robust")
added a sanity check to the #NM handler to verify that we never cause
the "Device Not Available" exception in kernel mode.
However, that check actually pinpointed a (fundamental) race where we do
cause that exception as part of the signal stack FPU state save/restore
code.
Because we use the floating point instructions themselves to save and
restore state directly from user mode, we cannot do that atomically with
testing the TS_USEDFPU bit: the user mode access itself may cause a page
fault, which causes a task switch, which saves and restores the FP/MMX
state from the kernel buffers.
This kind of "recursive" FP state save is fine per se, but it means that
when the signal stack save/restore gets restarted, it will now take the
'#NM' exception we originally tried to avoid. With preemption this can
happen even without the page fault - but because of the user access, we
cannot just disable preemption around the save/restore instruction.
There are various ways to solve this, including using the
"enable/disable_page_fault()" helpers to not allow page faults at all
during the sequence, and fall back to copying things by hand without the
use of the native FP state save/restore instructions.
However, the simplest thing to do is to just allow the #NM from kernel
space, but fix the race in setting and clearing CR0.TS that this all
exposed: the TS bit changes and the TS_USEDFPU bit absolutely have to be
atomic wrt scheduling, so while the actual state save/restore can be
interrupted and restarted, the act of actually clearing/setting CR0.TS
and the TS_USEDFPU bit together must not.
Instead of just adding random "preempt_disable/enable()" calls to what
is already excessively ugly code, this introduces some helper functions
that mostly mirror the "kernel_fpu_begin/end()" functionality, just for
the user state instead.
Those helper functions should probably eventually replace the other
ad-hoc CR0.TS and TS_USEDFPU tests too, but I'll need to think about it
some more: the task switching functionality in particular needs to
expose the difference between the 'prev' and 'next' threads, while the
new helper functions intentionally were written to only work with
'current'.
Anton Blanchard [Wed, 15 Feb 2012 18:48:22 +0000 (18:48 +0000)]
powerpc/perf: power_pmu_start restores incorrect values, breaking frequency events
perf on POWER stopped working after commit e050e3f0a71b (perf: Fix
broken interrupt rate throttling). That patch exposed a bug in
the POWER perf_events code.
Since the PMCs count upwards and take an exception when the top bit
is set, we want to write 0x80000000 - left in power_pmu_start. We were
instead programming in left which effectively disables the counter
until we eventually hit 0x80000000. This could take seconds or longer.
With the patch applied I get the expected number of samples:
SAMPLE events: 9948
Signed-off-by: Anton Blanchard <anton@samba.org> Acked-by: Paul Mackerras <paulus@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: <stable@kernel.org>
powerpc: Disable interrupts early in Program Check
Program Check exceptions are the result of WARNs, BUGs, some
type of breakpoints, kprobe, and other illegal instructions.
We want interrupts (and thus preemption) to remain disabled
while doing the initial stage of testing the reason and
branching off to a debugger or kprobe, so we are still on
the original CPU which makes debugging easier in various cases.
This is how the code was intended, hence the local_irq_enable()
right in the middle of program_check_exception().
However, the assembly exception prologue for that exception was
incorrectly marked as enabling interrupts, which defeats that
(and records a redundant enable with lockdep).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Upstream changes to the way PHB resources are registered
broke the resource fixup for FSL boards.
We can no longer rely on the resource pointer array for the PHB's
pci_bus structure, so let's leave it alone and go straight for
the PHB resources instead. This also makes the code generally
more readable.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Ira Snyder [Fri, 6 Jan 2012 12:34:07 +0000 (12:34 +0000)]
powerpc: Fix kernel log of oops/panic instruction dump
A kernel oops/panic prints an instruction dump showing several
instructions before and after the instruction which caused the
oops/panic.
The code intended that the faulting instruction be enclosed in angle
brackets, however a bug caused the faulting instruction to be
interpreted by printk() as the message log level.
To fix this, the KERN_CONT log level is added before the actual text of
the printed message.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu> Cc: Paul Mackerras <paulus@samba.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: linuxppc-dev@lists.ozlabs.org Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Alexey Dobriyan [Sat, 14 Jan 2012 18:44:49 +0000 (21:44 +0300)]
crypto: sha512 - use standard ror64()
Use standard ror64() instead of hand-written.
There is no standard ror64, so create it.
The difference is shift value being "unsigned int" instead of uint64_t
(for which there is no reason). gcc starts to emit native ROR instructions
which it doesn't do for some reason currently. This should make the code
faster.
Patch survives in-tree crypto test and ping flood with hmac(sha512) on.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Thomas Graf [Wed, 15 Feb 2012 04:09:46 +0000 (04:09 +0000)]
veth: Enforce minimum size of VETH_INFO_PEER
VETH_INFO_PEER carries struct ifinfomsg plus optional IFLA
attributes. A minimal size of sizeof(struct ifinfomsg) must be
enforced or we may risk accessing that struct beyond the limits
of the netlink message.
Signed-off-by: Thomas Graf <tgraf@suug.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the MAC HW initialization and
the HW feature verification from the open to the probe
function as D. Miller suggested.
So the patch actually reorganizes and tidies-up some parts of
the driver and indeed fixes some problem when tune its HW features.
These can be overwritten by looking at the HW cap register at
run-time and that generated problems.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Reviewed-by: Francesco Virlinzi <francesco.virlinzi@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
stmmac: request_irq when use an ext wake irq line (v2)
In case of we use an external Wake-Up IRQ line
(priv->wol_irq != dev->irq) we need to invoke the
request_irq.
Signed-off-by: Francesco Virlinzi <francesco.virlinzi@st.com> Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tim Gardner [Wed, 15 Feb 2012 07:50:15 +0000 (07:50 +0000)]
ipheth: Add iPhone 4S
BugLink: http://bugs.launchpad.net/bugs/900802 Cc: stable@vger.kernel.org 3.2+ Signed-off-by: Till Kamppeter <till.kamppeter@gmail.com> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net>
mlx4: add unicast steering entries to resource_tracker
Add unicast steering entries to resource tracker.
Do qp_detach also for these entries when VF doesn't shut down gracefully.
Otherwise there is leakage of these resources, since they are not tracked.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il> Reviewed-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il> Signed-off-by: David S. Miller <davem@davemloft.net>
When adding new unicast steer entry, before moving qp to state ready,
actually before calling mlx4_RST2INIT_QP_wrapper(), there were added
a lot of entries with local_qpn=0 into radix tree.
This fact impacted the get_res() function and proper functioning
of resource tracker in addition to adding trash entries into radix tree.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il> Reviewed-by: Yevgeny Petrilin <yevgenyp@melllanox.co.il> Signed-off-by: David S. Miller <davem@davemloft.net>
When passing MLX4_UC_STEER=1 it was translated to value 2
after mlx4_QP_ATTACH_wrapper. Therefore in new_steering_entry()
unicast steer entries were added to index 2 of array of size 2.
Fixing this bug by shift right to one position.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il> Reviewed-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il> Signed-off-by: David S. Miller <davem@davemloft.net>
regmap: Fix cache defaults initialization from raw cache defaults
Currently registers with a value of 0 are ignored when initializing the register
defaults from raw defaults. This worked in the past, because registers without a
explicit default were assumed to have a default value of 0. This was changed in
commit b03622a8 ("regmap: Ensure rbtree syncs registers set to zero properly").
As a result registers, which have a raw default value of 0 are now assumed to
have no default. This again can result in unnecessary writes when syncing the
cache. It will also result in unnecessary reads for e.g. the first update
operation. In the case where readback is not possible this will even let the
update operation fail, if the register has not been written to before.
So this patch removes the check. Instead it adds a check to ignore raw defaults
for registers which are volatile, since those registers are not cached.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Cc: stable@vger.kernel.org
Linus Torvalds [Wed, 15 Feb 2012 16:05:18 +0000 (08:05 -0800)]
i387: fix sense of sanity check
The check for save_init_fpu() (introduced in commit 5b1cbac37798: "i387:
make irq_fpu_usable() tests more robust") was the wrong way around, but
I hadn't noticed, because my "tests" were bogus: the FPU exceptions are
disabled by default, so even doing a divide by zero never actually
triggers this code at all unless you do extra work to enable them.
So if anybody did enable them, they'd get one spurious warning.
Ondrej Zary [Fri, 10 Feb 2012 17:59:17 +0000 (18:59 +0100)]
Resurrect Intel740 driver: i740fb
This is a resurrection of an old (like 2.4.19) out-of-tree driver for
Intel740 graphics cards and adaptation for recent kernels. The old driver by
Andrey Ulanov is located at: http://sourceforge.net/projects/i740fbdev/files/
This is a new driver based on skeletonfb, using most of the low level HW code
from the old driver. The DDC code is completely new.
The driver was tested on two 8MB cards: Protac AG240D and Diamond Stealth II
G460.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org> Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Linus Torvalds [Tue, 14 Feb 2012 23:26:42 +0000 (15:26 -0800)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
One small bug fix from Axel plus a fix for a build failure in unrealistic
but commonly built configs which for some reason manage to survive for
an awfully long time in -next without any reports.
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: Fix getting voltage in max8649_enable_time()
regulator: Fix mc13xxx regulator modular build (again)
Linus Torvalds [Tue, 14 Feb 2012 23:21:25 +0000 (15:21 -0800)]
Merge branch 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
Quoth BenH:
"Here are a few powerpc fixes for 3.3, all pretty trivial. I also
added the patch to define GET_IP/SET_IP so we can use some more
asm-generic goodness."
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/pseries/eeh: Fix crash when error happens during device probe
powerpc/pseries: Fix partition migration hang in stop_topology_update
powerpc/powernv: Disable interrupts while taking phb->lock
powerpc: Fix WARN_ON in decrementer_check_overflow
powerpc/wsp: Fix IRQ affinity setting
powerpc: Implement GET_IP/SET_IP
powerpc/wsp: Permanently enable PCI class code workaround
Linus Torvalds [Tue, 14 Feb 2012 23:20:50 +0000 (15:20 -0800)]
Merge tag 'mmc-fixes-for-3.3-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
MMC fixes for 3.3-rc4:
* The most visible fix here is against a regression introduced in 3.3-rc1
that ran cards in Ultra High Speed mode even when they failed to initialize
in that mode, leading to lower-speed cards failing to mount.
* A lockdep warning introduced in 3.3-rc1 is fixed.
* Various other small driver fixes, most notably for a NULL dereference
when using highmem with dw_mmc.
* tag 'mmc-fixes-for-3.3-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc:
mmc: dw_mmc: Fix PIO mode with support of highmem
mmc: atmel-mci: save and restore sdioirq when soft reset is performed
mmc: block: Init ro_lock sysfs attr to fix lockdep warnings
mmc: sh_mmcif: fix late delayed work initialisation
mmc: tmio_mmc: fix card eject during IO with DMA
mmc: core: Fix comparison issue in mmc_compare_ext_csds
mmc: core: Fix PowerOff Notify suspend/resume
mmc: sdhci-pci: set Medfield SDIO as non-removable
mmc: core: add the capability for broken voltage
mmc: core: Fix low speed mmc card detection failure
mmc: esdhc: set the timeout to the max value
mmc: esdhc: add PIO mode support
mmc: core: Ensure clocks are always enabled before host interaction
mmc: of_mmc_spi: fix little endian support
mmc: core: UHS sdio card that fails should not exceed 50MHz
mmc: esdhc: fix errors when booting kernel on Freescale eSDHC version 2.3
Linus Torvalds [Tue, 14 Feb 2012 23:20:11 +0000 (15:20 -0800)]
Merge tag 'stable/for-linus-fixes-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Two fixes for VCPU offlining; One to fix the string format exposed
by the xen-pci[front|back] to conform to the one used in majority of
PCI drivers; Two fixes to make the code more resilient to invalid
configurations.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
* tag 'stable/for-linus-fixes-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xenbus_dev: add missing error check to watch handling
xen/pci[front|back]: Use %d instead of %1x for displaying PCI devfn.
xen pvhvm: do not remap pirqs onto evtchns if !xen_have_vector_callback
xen/smp: Fix CPU online/offline bug triggering a BUG: scheduling while atomic.
xen/bootup: During bootup suppress XENBUS: Unable to read cpu state
Eric Dumazet [Tue, 14 Feb 2012 10:27:09 +0000 (10:27 +0000)]
3c59x: shorten timer period for slave devices
Jean Delvare reported bonding on top of 3c59x adapters was not detecting
network cable removal fast enough.
3c59x indeed uses a 60 seconds timer to check link status if carrier is
on, and 5 seconds if carrier is off.
This patch reduces timer period to 5 seconds if device is a bonding
slave.
Reported-by: Jean Delvare <jdelvare@suse.de> Acked-by: Jean Delvare <jdelvare@suse.de> Acked-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 14 Feb 2012 10:11:59 +0000 (10:11 +0000)]
netpoll: netpoll_poll_dev() should access dev->flags
commit 5a698af53f (bond: service netpoll arp queue on master device)
tested IFF_SLAVE flag against dev->priv_flags instead of dev->flags
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Cc: WANG Cong <amwang@redhat.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Neal Cardwell [Mon, 13 Feb 2012 20:22:08 +0000 (20:22 +0000)]
tcp: fix tcp_shifted_skb() adjustment of lost_cnt_hint for FACK
This commit ensures that lost_cnt_hint is correctly updated in
tcp_shifted_skb() for FACK TCP senders. The lost_cnt_hint adjustment
in tcp_sacktag_one() only applies to non-FACK senders, so FACK senders
need their own adjustment.
This applies the spirit of 1e5289e121372a3494402b1b131b41bfe1cf9b7f -
except now that the sequence range passed into tcp_sacktag_one() is
correct we need only have a special case adjustment for FACK.
Signed-off-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Tue, 14 Feb 2012 17:09:24 +0000 (09:09 -0800)]
Merge tag 'sound-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
sound fixes for 3.3-rc4
Basically all small fixes suited as rc4: a few HD-audio regression fixes,
a stable fix for an old Dell laptop with intel8x0, and a simple fix for
ASoC fsi.
* tag 'sound-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: intel8x0: Fix default inaudible sound on Gateway M520
ALSA: hda - Fix silent speaker output on Acer Aspire 6935
ALSA: hda - Fix initialization of secondary capture source on VT1705
ASoC: fsi: fixup fsi_pointer() calculation method
ALSA: hda - Fix mute-LED VREF value for new HP laptops
Dave Airlie [Mon, 13 Feb 2012 12:18:37 +0000 (12:18 +0000)]
drm/radeon/kms: drop lock in return path of radeon_fence_count_emitted.
Silly bad return path.
Reported-and-Tested-by: Mikko Vinni Reviewed-by: Alex Deucher <alexander.deucher@amd.com> CC: stable@vger.kernel.org Signed-off-by: Dave Airlie <airlied@redhat.com>
Daniel T Chen [Tue, 14 Feb 2012 04:44:22 +0000 (23:44 -0500)]
ALSA: intel8x0: Fix default inaudible sound on Gateway M520
BugLink: https://bugs.launchpad.net/bugs/930842
The reporter states that audio is inaudible by default without muting
'External Amplifier'. Add a quirk to handle his SSID so that changing
the control is not necessary.
Reported-and-tested-by: Benjamin Carlson <elderbubba0810@gmail.com> Cc: <stable@kernel.org> Signed-off-by: Daniel T Chen <crimsun@ubuntu.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Linus Torvalds [Tue, 14 Feb 2012 04:34:44 +0000 (20:34 -0800)]
Merge git://git.samba.org/sfrench/cifs-2.6
* git://git.samba.org/sfrench/cifs-2.6:
cifs: don't return error from standard_receive3 after marking response malformed
cifs: request oplock when doing open on lookup
cifs: fix error handling when cifscreds key payload is an error
This updates the sha512 fix so that it doesn't cause excessive stack
usage on i386. This is done by reverting to the original code, and
avoiding the W duplication by moving its initialisation into the loop.
As the underlying code is in fact the one that we have used for years,
I'm pushing this now instead of postponing to the next cycle.
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: sha512 - Avoid stack bloat on i386
crypto: sha512 - Use binary and instead of modulus
powerpc/pseries/eeh: Fix crash when error happens during device probe
EEH may happen during a PCI driver probe. If the driver is trying to
access some register in a loop, the EEH code will try to print the
driver name. But the driver pointer in struct pci_dev is not set until
probe returns successfully.
Use a function to test if the device and the driver pointer is NULL
before accessing the driver's name.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Brian King [Wed, 11 Jan 2012 06:56:04 +0000 (06:56 +0000)]
powerpc/pseries: Fix partition migration hang in stop_topology_update
This fixes a hang that was observed during live partition migration.
Since stop_topology_update must not be called from an interrupt
context, call it earlier in the migration process. The hang observed
can be seen below:
powerpc: Fix WARN_ON in decrementer_check_overflow
We use __get_cpu_var() which triggers a false positive warning
in smp_processor_id() thinking interrupts are enabled (at this
point, they are soft-enabled but hard-disabled).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We call the cache_hwirq_map() function with a linux IRQ number
but it expects a HW irq number. This triggers a BUG on multic-chip
setups in addition to not doing the right thing.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
powerpc/wsp: Permanently enable PCI class code workaround
It appears that on the Chroma card, the class code of the root
complex is still wrong even on DD2 or later chips. This could
be a firmware issue, but that breaks resource allocation so let's
unconditionally fix it up.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com> Acked-by: Will Newton <will.newton@imgtec.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Chris Ball <cjb@laptop.org>
mmc: atmel-mci: save and restore sdioirq when soft reset is performed
Sometimes a software reset is needed. Then some registers are saved and
restored but the interrupt mask register is missing. It causes issues
with sdio devices whose interrupts are masked after reset.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Chris Ball <cjb@laptop.org>
mmc: sh_mmcif: fix late delayed work initialisation
If the driver is loaded with a card in the slot, mmc_add_host() will
schedule an immediate card-detection work, which will start IO and wait
for command completion. Usually the kernel first returns to the sh_mmcif
probe function, lets it finish and only then schedules the rescan work.
But sometimes, expecially under heavy system load, the work will be
scheduled immediately before returning to the probe method. In this case
it is important for the driver to be fully prepared for IO. For sh_mmcif
this means, that also the timeout work has to be initialised before
calling mmc_add_host(). It is also better to prepare interrupts
beforehand. Besides, since mmc_add_host() does card-detection itself,
there is no need to do it again immediately afterwards.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by: Chris Ball <cjb@laptop.org>
When DMA is in use and the card is ejected during IO, DMA transfers have to
be terminated, otherwise the dmaengine driver fails to operate properly,
when the card is re-inserted.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by: Chris Ball <cjb@laptop.org>
Jurgen Heeks [Wed, 1 Feb 2012 12:30:55 +0000 (13:30 +0100)]
mmc: core: Fix comparison issue in mmc_compare_ext_csds
Found this issue during code review. Actually, there are two issues which
both compensate together in lucky case. In unlucky case the bus width
probing might not work as expected.
Girish K S [Tue, 31 Jan 2012 10:14:03 +0000 (15:44 +0530)]
mmc: core: Fix PowerOff Notify suspend/resume
Modified the mmc_poweroff to resume before sending the poweroff
notification command. In sleep mode only AWAKE and RESET commands are
allowed, so before sending the poweroff notification command resume from
sleep mode and then send the notification command.
PowerOff Notify is tested on a Synopsis Designware Host Controller
(eMMC 4.5). The suspend to RAM and resume works fine.
Signed-off-by: Girish K S <girish.shivananjappa@linaro.org> Tested-by: Girish K S <girish.shivananjappa@linaro.org> Reviewed-by: Saugata Das <saugata.das@linaro.org> Signed-off-by: Chris Ball <cjb@laptop.org>
Jaehoon Chung [Mon, 16 Jan 2012 08:49:01 +0000 (17:49 +0900)]
mmc: core: add the capability for broken voltage
There is an understood mismatch between the voltage the host controller is
set to and the voltage supplied to the card by a fixed voltage regulator.
Teaching the driver to accept the mismatch is overly complicated. Instead
just accept the regulator's voltage.
This patch adds MMC_CAP2_BROKEN_VOLTAGE.
If the voltage didn't satisfy between min_uV and max_uV, try to change
the voltage in core.c. When changing the voltage, maybe use
regulator_set_voltage().
In regulator_set_voltage(), check the below condition.
/* sanity check */
if (!rdev->desc->ops->set_voltage &&
!rdev->desc->ops->set_voltage_sel) {
ret = -EINVAL;
goto out;
}
If some board should use the fixed-regulator, always return -EINVAL.
Then, eMMC didn't initialize always.
So if use a fixed-regulator, we need to add the MMC_CAP2_BROKEN_VOLTAGE.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Chris Ball <cjb@laptop.org>
Jerry Huang [Mon, 16 Jan 2012 06:13:04 +0000 (14:13 +0800)]
mmc: esdhc: set the timeout to the max value
When accessing the card on some FSL platform boards (e.g p2020, p1010,
mpc8536), the following error is reported with the timeout value calculated:
mmc0: Got data interrupt 0x00000020 even though no data operation was
in progress.
mmc0: Got data interrupt 0x00000020 even though no data operation was
in progress.
So we skip the calculation of timeout and use the max value to fix it.
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com> Signed-off-by: Gao Guanhua <B22826@freescale.com> Signed-off-by: Xie Xiaobo <X.Xie@freescale.com> Acked-by: Anton Vorontsov <cbouatmailru@gmail.com> Signed-off-by: Chris Ball <cjb@laptop.org>
Jerry Huang [Mon, 16 Jan 2012 06:13:03 +0000 (14:13 +0800)]
mmc: esdhc: add PIO mode support
For some FSL ESDHC controllers (e.g. P2020E, Rev1.0), the SDHC can not
work on DMA mode because of the hardware bug, so we set a broken dma flag
and use PIO mode.
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com> Signed-off-by: Gao Guanhua <B22826@freescale.com> Acked-by: Anton Vorontsov <cbouatmailru@gmail.com> Signed-off-by: Chris Ball <cjb@laptop.org>
mmc: core: Ensure clocks are always enabled before host interaction
Ensure clocks are always enabled before any interaction with the
host controller driver. This makes sure that there is no race
between host execution and the core layer turning off clocks
in different context with clock gating framework.
Signed-off-by: Sujit Reddy Thumma <sthumma@codeaurora.org> Acked-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Per Forlin <per.forlin@stericsson.com> Signed-off-by: Chris Ball <cjb@laptop.org>
Philip Rakity [Thu, 26 Jan 2012 14:57:10 +0000 (06:57 -0800)]
mmc: core: UHS sdio card that fails should not exceed 50MHz
A UHS sdio card that fails initialization at 1.8v signaling is not in
UHS mode. We cannot use the speed in the the cis to reflect the bus
speed as this is the maxiumum value and will not reflect the fact
that the host is operating at a lower (non uhs) bus speed.
Signed-off-by: Philip Rakity <prakity@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Reviewed-by: Aaron Lu <aaron.lu@amd.com> Signed-off-by: Chris Ball <cjb@laptop.org>
Linus Torvalds [Tue, 14 Feb 2012 00:59:53 +0000 (16:59 -0800)]
Merge tag 'for-linus' of git://github.com/rustyrussell/linux
* tag 'for-linus' of git://github.com/rustyrussell/linux:
module: fix broken isapnp handling in file2alias
module: make module param bint handle nul value
Arnd Bergmann [Mon, 13 Feb 2012 23:25:44 +0000 (23:25 +0000)]
Merge branch 'at91-fixes' of git://github.com/at91linux/linux-at91 into fixes
* 'at91-fixes' of git://github.com/at91linux/linux-at91:
ARM: at91: drop ide driver in favor of the pata one
pata/at91: use newly introduced SMC accessors
ARM: at91: add accessor to manage SMC
ARM: at91:rtc/rtc-at91sam9: ioremap register bank
ARM: at91: USB AT91 gadget registration for module
Linus Torvalds [Mon, 13 Feb 2012 22:20:43 +0000 (14:20 -0800)]
Merge tag 'battery-fixes-for-v3.3-rc2' of git://git.infradead.org/users/cbou/battery-urgent
Just a few small fixes for a bunch of drivers. Nothing noteworthy.
* tag 'battery-fixes-for-v3.3-rc2' of git://git.infradead.org/users/cbou/battery-urgent:
lp8727_charger: Add terminating entry for i2c_device_id table
power_supply: Fix modalias for charger-manager
lp8727_chager: Fix permissions on a header file
bq27x00_battery: Fix flag register read
Revert "bq27x00_battery: Fix reporting status value for bq27500 battery"
Linus Torvalds [Mon, 13 Feb 2012 22:19:45 +0000 (14:19 -0800)]
Merge branch 'for-linus' of git://oss.sgi.com/xfs/xfs
Two bugfixes in XFS for 3.3: one fix passes KMEM_SLEEP to kmem_realloc
instead of 0, and the other resolves a possible deadlock in xfs quotas.
* 'for-linus' of git://oss.sgi.com/xfs/xfs:
xfs: use a normal shrinker for the dquot freelist
xfs: pass KM_SLEEP flag to kmem_realloc() in xlog_recover_add_to_cnt_trans()
Linus Torvalds [Mon, 13 Feb 2012 22:16:07 +0000 (14:16 -0800)]
Merge branch 'omap-fixes-warnings' of git://git.linaro.org/people/rmk/linux-arm
This set of changes are fixing various section mismatch warnings which
look to be completely valid. Primerily, those which are fixed are those
which can cause oopses by manipulation of driver binding via sysfs. For
example: calling code marked __init from driver probe __devinit
functions.
Some of these changes will be reworked at the next merge window when the
underlying reasons are sorted out. In the mean time, I think it's
important to have this fixed for correctness.
Also included in this set are fixes to various error messages in OMAP -
including making them gramatically correct, fixing a few spelling
errors, and more importantly, making them greppable by unwrapping them.
Tony Lindgren has acked all these patches, put them out for testing a
week ago, and I've tested them on the platforms I have.
Linus Torvalds [Mon, 13 Feb 2012 22:15:22 +0000 (14:15 -0800)]
Merge branch 'omap-fixes-urgent' of git://git.linaro.org/people/rmk/linux-arm
This pull request covers the major oopsing issues with OMAP, caused by
the lack of the TWL driver. Even when the TWL driver is not built in,
we shouldn't oops.
* 'omap-fixes-urgent' of git://git.linaro.org/people/rmk/linux-arm:
ARM: omap: fix broken twl-core dependencies and ifdefs
ARM: omap: fix oops in drivers/video/omap2/dss/dpi.c
ARM: omap: fix oops in arch/arm/mach-omap2/vp.c when pmic is not found
Linus Torvalds [Mon, 13 Feb 2012 21:56:14 +0000 (13:56 -0800)]
i387: make irq_fpu_usable() tests more robust
Some code - especially the crypto layer - wants to use the x86
FP/MMX/AVX register set in what may be interrupt (typically softirq)
context.
That *can* be ok, but the tests for when it was ok were somewhat
suspect. We cannot touch the thread-specific status bits either, so
we'd better check that we're not going to try to save FP state or
anything like that.
Now, it may be that the TS bit is always cleared *before* we set the
USEDFPU bit (and only set when we had already cleared the USEDFP
before), so the TS bit test may actually have been sufficient, but it
certainly was not obviously so.
So this explicitly verifies that we will not touch the TS_USEDFPU bit,
and adds a few related sanity-checks. Because it seems that somehow
AES-NI is corrupting user FP state. The cause is not clear, and this
patch doesn't fix it, but while debugging it I really wanted the code to
be more obviously correct and robust.
projects / mv-sheeva.git / log