In register_netdevice(), when ndo_init() is successful and later
some error occurred, ndo_uninit() will be called.
So dummy deivce is desirable to implement ndo_uninit() method
to free percpu stats for this case.
And, ndo_uninit() is also called along with dev->destructor() when
device is unregistered, so in order to prevent dev->dstats from
being freed twice, dev->destructor is modified to free_netdev().
Signed-off-by: Hiroaki SHIMODA <shimoda.hiroaki@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephane Fillod <fillods@users.sf.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A parameter set exists for WRED mode, called wred_set, to hold the same
values for qavg and qidlestart across all VQs. The WRED mode values had
been previously held in the VQ for the default DP. After these values
were moved to wred_set, the VQ for the default DP was no longer created
automatically (so that it could be omitted on purpose, to have packets
in the default DP enqueued directly to the device without using RED).
However, gred_dump() was overlooked during that change; in WRED mode it
still reads qavg/qidlestart from the VQ for the default DP, which might
not even exist. As a result, this command sequence will cause an oops:
This fixes gred_dump() in WRED mode to use the values held in wred_set.
Signed-off-by: David Ward <david.ward@ll.mit.edu> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At the beginning of ks_rcv(), a for loop retrieves the
header information relevant to all the frames stored
in the mac's internal buffers. The number of pending
frames is stored as an 8 bits field in KS_RXFCTR.
If interrupts are disabled long enough to allow for more than
32 frames to accumulate in the MAC's internal buffers, a buffer
overflow occurs.
This patch fixes the problem by making the
driver's frame_head_info buffer big enough.
Well actually, since the chip appears to have 12K of
internal rx buffers and the shortest ethernet frame should
be 64 bytes long, maybe the limit could be set to
12*1024/64 = 192 frames, but 255 should be safer.
Signed-off-by: Davide Ciminaghi <ciminaghi@gnudd.com> Signed-off-by: Raffaele Recalcati <raffaele.recalcati@bticino.it> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SMSC911x driver resets the ->head, ->data and ->tail pointers in the
skb on the reset path in order to avoid buffer overflow due to packet
padding performed by the hardware.
This patch fixes the receive path so that the skb pointers are fixed up
after the data has been read from the device, The error path is also
fixed to use number of words consistently and prevent erroneous FIFO
fastforwarding when skipping over bad data.
Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We set intr mask before its handler is registered, this does not work well when
8139cp is sharing irq line with other devices. As the irq could be enabled by
the device before 8139cp's hander is registered which may lead unhandled
irq. Fix this by introducing an helper cp_irq_enable() and call it after
request_irq().
Signed-off-by: Jason Wang <jasowang@redhat.com> Reviewed-by: Flavio Leitner <fbl@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Problem:
There was two separate work_struct structures which share one
handler. Unfortunately getting atl1_adapter structure from
work_struct in case of DMA error was done from incorrect
offset which cause kernel panics.
Solution:
The useless work_struct for DMA error removed and
handler name changed to more generic one.
Signed-off-by: Tony Zelenoff <antonz@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix a code path in tcp_rcv_rtt_update() that was comparing scaled and
unscaled RTT samples.
The intent in the code was to only use the 'm' measurement if it was a
new minimum. However, since 'm' had not yet been shifted left 3 bits
but 'new_sample' had, this comparison would nearly always succeed,
leading us to erroneously set our receive-side RTT estimate to the 'm'
sample when that sample could be nearly 8x too high to use.
The overall effect is to often cause the receive-side RTT estimate to
be significantly too large (up to 40% too large for brief periods in
my tests).
Signed-off-by: Neal Cardwell <ncardwell@google.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As soon as an skb is queued into socket error queue, another thread
can consume it, so we are not allowed to reference skb anymore, or risk
use after free.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As soon as an skb is queued into socket receive_queue, another thread
can consume it, so we are not allowed to reference skb anymore, or risk
use after free.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This happened on a machine with a custom hotplug script calling nameif,
probably due to slow firmware loading. At the time nameif uses ethtool
to gather interface information, i2400m->fw_name is zero and so a null
pointer dereference occurs from within i2400m_get_drvinfo().
Signed-off-by: Phil Sutter <phil.sutter@viprinet.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a slave comes up, we're unsetting the current_arp_slave without
removing active flags from it, which can lead to situations where we have
more than one slave with active flags in active-backup mode.
To avoid this situation we must remove the active flags from a slave before
removing it as a current_arp_slave.
Signed-off-by: Veaceslav Falico <vfalico@redhat.com> Signed-off-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: Andy Gospodarek <andy@greyhouse.net> Signed-off-by: Marcelo Ricardo Leitner <mleitner@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A phonet packet is limited to USHRT_MAX bytes, this is never checked during
tx which means that the user can specify any size he wishes, and the kernel
will attempt to allocate that size.
In the good case, it'll lead to the following warning, but it may also cause
the kernel to kick in the OOM and kill a random task on the server.
Convert array index from the loop bound to the loop index.
And remove the void type conversion to ip6_mc_del1_src() return
code, seem it is unnecessary, since ip6_mc_del1_src() does not
use __must_check similar attribute, no compiler will report the
warning when it is removed.
v2: enrich the commit header
Signed-off-by: RongQing.Li <roy.qing.li@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As it stands the bridge IGMP snooping system will respond to
group leave messages with queries for remaining membership.
This is both unnecessary and undesirable. First of all any
multicast routers present should be doing this rather than us.
What's more the queries that we send may end up upsetting other
multicast snooping swithces in the system that are buggy.
In fact, we can simply remove the code that send these queries
because the existing membership expiry mechanism doesn't rely
on them anyway.
So this patch simply removes all code associated with group
queries in response to group leave messages.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
getsockopt(..., SCTP_EVENTS, ...) performs a length check and returns
an error if the user provides less bytes than the size of struct
sctp_event_subscribe.
Struct sctp_event_subscribe needs to be extended by an u8 for every
new event or notification type that is added.
This obviously makes getsockopt fail for binaries that are compiled
against an older versions of <net/sctp/user.h> which do not contain
all event types.
This patch changes getsockopt behaviour to no longer return an error
if not enough bytes are being provided by the user. Instead, it
returns as much of sctp_event_subscribe as fits into the provided buffer.
This leads to the new behavior that users see what they have been aware
of at compile time.
The setsockopt(..., SCTP_EVENTS, ...) API is already behaving like this.
Signed-off-by: Thomas Graf <tgraf@suug.ch> Acked-by: Vlad Yasevich <vladislav.yasevich@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
vmsplice()/splice(pipe, socket) call do_tcp_sendpages() one page at a
time, adding at most 4096 bytes to an skb. (assuming PAGE_SIZE=4096)
The call to tcp_push() at the end of do_tcp_sendpages() forces an
immediate xmit when pipe is not already filled, and tso_fragment() try
to split these skb to MSS multiples.
4096 bytes are usually split in a skb with 2 MSS, and a remaining
sub-mss skb (assuming MTU=1500)
This makes slow start suboptimal because many small frames are sent to
qdisc/driver layers instead of big ones (constrained by cwnd and packets
in flight of course)
In fact, applications using sendmsg() (adding an additional memory copy)
instead of vmsplice()/splice()/sendfile() are a bit faster because of
this anomaly, especially if serving small files in environments with
large initial [c]wnd.
Call tcp_push() only if MSG_MORE is not set in the flags parameter.
This bit is automatically provided by splice() internals but for the
last page, or on all pages if user specified SPLICE_F_MORE splice()
flag.
In some workloads, this can reduce number of sent logical packets by an
order of magnitude, making zero-copy TCP actually faster than
one-copy :)
Reported-by: Tom Herbert <therbert@google.com> Cc: Nandita Dukkipati <nanditad@google.com> Cc: Neal Cardwell <ncardwell@google.com> Cc: Tom Herbert <therbert@google.com> Cc: Yuchung Cheng <ycheng@google.com> Cc: H.K. Jerry Chu <hkchu@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Mahesh Bandewar <maheshb@google.com> Cc: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For every transmitted packet, ppp_start_xmit() will stop the netdev
queue and then, if appropriate, restart it. This causes the TX softirq
to run, entirely gratuitously.
This is "only" a waste of CPU time in the normal case, but it's actively
harmful when the PPP device is a TEQL slave — the wakeup will cause the
offending device to receive the next TX packet from the TEQL queue, when
it *should* have gone to the next slave in the list. We end up seeing
large bursts of packets on just *one* slave device, rather than using
the full available bandwidth over all slaves.
This patch fixes the problem by *not* unconditionally stopping the queue
in ppp_start_xmit(). It adds a return value from ppp_xmit_process()
which indicates whether the queue should be stopped or not.
It *doesn't* remove the call to netif_wake_queue() from
ppp_xmit_process(), because other code paths (especially from
ppp_output_wakeup()) need it there and it's messy to push it out to the
other callers to do it based on the return value. So we leave it in
place — it's a no-op in the case where the queue wasn't stopped, so it's
harmless in the TX path.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
->root_flags is __le64 and all accesses to it go through the helpers
that do proper conversions. Except for btrfs_root_readonly(), which
checks bit 0 as in host-endian...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Cc: Chris Mason <chris.mason@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Restore the original logics ("fail on mountpoints, negatives and in
case of fh_compose() failures"). Since commit 8177e (nfsd: clean up
readdirplus encoding) that got broken -
rv = fh_compose(fhp, exp, dchild, &cd->fh);
if (rv)
goto out;
if (!dchild->d_inode)
goto out;
rv = 0;
out:
is equivalent to
rv = fh_compose(fhp, exp, dchild, &cd->fh);
out:
and the second check has no effect whatsoever...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Cc: "J. Bruce Fields" <bfields@fieldses.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to the latest USB ID database these are all RT2770 / RT2870 / RT307x
devices.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Cc: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Alan Cox <alan@linux.intel.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Cc: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reported-by: Teika Kazura <teika@lavabit.com> Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Cc: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Belkin's Connect N150 Wireless USB Adapter, model F7D1101 version 2, uses ID 0x945b.
Chipset info: rt: 3390, rf: 000b, rev: 3213.
I have just bought one, which started to work perfectly after the ID was added through this patch.
Signed-off-by: Eduardo Bacchi Kienetz <eduardo@kienetz.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Cc: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sitecom WLA4000 (USB ID 0x0df6:0x0060) is an RT3072 chipset.
Sitecom WLA5000 (USB ID 0x0df6:0x0062) is an RT3572 chipset.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Cc: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Device are added as children of the bus master's parent device, but
spi_unregister_master() looks for devices to unregister in the bus
master's children. This results in the child devices not being
unregistered.
Fix this by registering devices as direct children of the bus master.
Commit 28d82dc1c4ed ("epoll: limit paths") that I did to limit the
number of possible wakeup paths in epoll is causing a few applications
to longer work (dovecot for one).
The original patch is really about limiting the amount of epoll nesting
(since epoll fds can be attached to other fds). Thus, we probably can
allow an unlimited number of paths of depth 1. My current patch limits
it at 1000. And enforce the limits on paths that have a greater depth.
This is captured in: https://bugzilla.redhat.com/show_bug.cgi?id=681578
Signed-off-by: Jason Baron <jbaron@redhat.com> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some BIOS implementations leave the Intel GPU interrupts enabled,
even though no one is handling them (f.e. i915 driver is never loaded).
Additionally the interrupt destination is not set up properly
and the interrupt ends up -somewhere-.
These spurious interrupts are "sticky" and the kernel disables
the (shared) interrupt line after 100.000+ generated interrupts.
Fix it by disabling the still enabled interrupts.
This resolves crashes often seen on monitor unplug.
Tested on the following boards:
- Intel DH61CR: Affected
- Intel DH67BL: Affected
- Intel S1200KP server board: Affected
- Asus P8H61-M LE: Affected, but system does not crash.
Probably the IRQ ends up somewhere unnoticed.
According to reports on the net, the Intel DH61WW board is also affected.
Many thanks to Jesse Barnes from Intel for helping
with the register configuration and to Intel in general
for providing public hardware documentation.
Signed-off-by: Thomas Jarosch <thomas.jarosch@intra2net.com> Tested-by: Charlie Suffin <charlie.suffin@stratus.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pm_runtime_get_sync returns a signed integer. In case of errors
it returns a negative value. This patch fixes the error check
by making it signed instead of unsigned thus preventing register
access if get_sync_fails. Also passes the error cause to the
debug message.
Cc: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pm_runtime_enable is being called after omap2430_musb_init. Hence
pm_runtime_get_sync in omap2430_musb_init does not have any effect (does
not enable clocks) resulting in a crash during register access. It is
fixed here.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes a bug which causes NULL pointer dereference in
ffs_ep0_ioctl. The bug happens when the FunctionFS is not bound (either
has not been bound yet or has been bound and then unbound) and can be
reproduced with running the following commands:
This patch (as154) fixes a self-deadlock that occurs when userspace
writes to the bConfigurationValue sysfs attribute for a hub with
children. The task tries to lock the bandwidth_mutex at a time when
it already owns the lock:
The attribute's method calls usb_set_configuration(),
which calls usb_disable_device() with the bandwidth_mutex
held.
usb_disable_device() unregisters the existing interfaces,
which causes the hub driver to be unbound.
The hub_disconnect() routine calls hub_quiesce(), which
calls usb_disconnect() for each of the hub's children.
usb_disconnect() attempts to acquire the bandwidth_mutex
around a call to usb_disable_device().
The solution is to make usb_disable_device() acquire the mutex for
itself instead of requiring the caller to hold it. Then the mutex can
cover only the bandwidth deallocation operation and not the region
where the interfaces are unregistered.
This has the potential to change system behavior slightly when a
config change races with another config or altsetting change. Some of
the bandwidth released from the old config might get claimed by the
other config or altsetting, make it impossible to restore the old
config in case of a failure. But since we don't try to recover from
config-change failures anyway, this doesn't matter.
[This should be marked for stable kernels that contain the commit fccf4e86200b8f5edd9a65da26f150e32ba79808 "USB: Free bandwidth when
usb_disable_device is called."
That commit was marked for stable kernels as old as 2.6.32.]
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1544) fixes a problem affecting some EHCI controllers.
They can generate interrupts whenever the STS_FLR status bit is turned
on, even though that bit is masked out in the Interrupt Enable
register.
Since the driver doesn't use STS_FLR anyway, the patch changes the
interrupt routine to clear that bit whenever it is set, rather than
leaving it alone.
These devices have a number of non serial interfaces as well. Use
the existing "Direct IP" blacklist to prevent binding to interfaces
which are handled by other drivers.
We also extend the "Direct IP" blacklist with with interfaces only
seen in "QMI" mode, assuming that these devices use the same
interface numbers for serial interfaces both in "Direct IP" and in
"QMI" mode.
This driver anticipates pch_uart_verify_port() is not called
during installation.
However, actually pch_uart_verify_port() is called during
installation.
As a result, memory access violation occurs like below.
0. initial value: use_dma=0
1. starup()
- dma channel is not allocated because use_dma=0
2. pch_uart_verify_port()
- Set use_dma=1
3. UART processing acts DMA mode because use_dma=1
- memory access violation occurs!
This patch fixes the issue.
Solution:
Whenever pch_uart_verify_port() is called and then
dma channel is not allocated, the channel should be allocated.
Fixed too small hardcoded timeout values for usb_control_msg
in driver for SiliconLabs cp210x-based usb-to-serial adapters.
Replaced with USB_CTRL_GET_TIMEOUT/USB_CTRL_SET_TIMEOUT.
flush request is issued in transaction commit code path, so looks using
GFP_KERNEL to allocate memory for flush request bio falls into the classic
deadlock issue. I saw btrfs and dm get it right, but ext4, xfs and md are
using GFP.
Signed-off-by: Shaohua Li <shli@fusionio.com> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Reviewed-by: Jan Kara <jack@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mel reports a BUG_ON(slot == NULL) in radix_tree_tag_set() on s390
3.0.13: called from __set_page_dirty_nobuffers() when page_remove_rmap()
tries to transfer dirty flag from s390 storage key to struct page and
radix_tree.
That would be because of reclaim's shrink_page_list() calling
add_to_swap() on this page at the same time: first PageSwapCache is set
(causing page_mapping(page) to appear as &swapper_space), then
page->private set, then tree_lock taken, then page inserted into
radix_tree - so there's an interval before taking the lock when the
radix_tree slot is empty.
We could fix this by moving __add_to_swap_cache()'s spin_lock_irq up
before the SetPageSwapCache. But a better fix is simply to do what's
five years overdue: Ken Chen introduced __set_page_dirty_no_writeback()
(if !PageDirty TestSetPageDirty) for tmpfs to skip all the radix_tree
overhead, and swap is just the same - it ignores the radix_tree tag, and
does not participate in dirty page accounting, so should be using
__set_page_dirty_no_writeback() too.
s390 testing now confirms that this does indeed fix the problem.
Under heavy load (flood ping) it is possible for the MDIO timeout to
expire before the loop checks the GO bit again. This patch adds an
additional check whether the operation was done before actually
returning -ETIMEDOUT.
To reproduce this bug, flood ping the device, e.g., ping -f -l 1000
After some time, a "timed out waiting for user access" warning
may appear. And even worse, link may go down since the PHY reported a
timeout.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at> Cc: Cyril Chemparathy <cyril@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current probing code is setting URB_NO_TRANSFER_DMA_MAP flag into a wrong urb
structure, and this causes BUG_ON with some USB host implementations.
This patch fixes the issue.
Removes allocation of coherent buffer for the control-request setup-packet
buffer from the yurex driver. Using coherent buffers for setup-packet is
obsolete and does not work with some USB host implementations.
A rather annoying and common case is when booting a PVonHVM guest
and exposing the PV KBD and PV VFB - as broken toolstacks don't
always initialize the backends correctly.
Normally The HVM guest is using the VGA driver and the emulated
keyboard for this (though upstream version of QEMU implements
PV KBD, but still uses a VGA driver). We provide a very basic
two-stage wait mechanism - where we wait for 30 seconds for all
devices, and then for 270 for all them except the two mentioned.
That allows us to wait for the essential devices, like network
or disk for the full 6 minutes.
To trigger this, put this in your guest config:
vfb = [ 'vnc=1, vnclisten=0.0.0.0 ,vncunused=1']
instead of this:
vnc=1
vnclisten="0.0.0.0"
Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
[v3: Split delay in non-essential (30 seconds) and essential
devices per Ian and Stefano suggestion]
[v4: Added comments per Stefano suggestion] Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since we are using the m2p_override we do have struct pages
corresponding to the user vma mmap'ed by gntdev.
Removing the VM_PFNMAP flag makes get_user_pages work on that vma.
An example test case would be using a Xen userspace block backend
(QDISK) on a file on NFS using O_DIRECT.
Since 2.6.30-rc1 clps711x serial driver hungs system. This is a result
of call disable_irq from ISR. synchronize_irq waits for end of interrupt
and goes to infinite loop. This patch fix this problem.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[Patch not needed upstream as this is a backport build bugfix - gregkh
gcc correctly complains:
util/hist.c: In function ‘__hists__add_entry’:
util/hist.c:240:27: error: invalid type argument of ‘->’ (have ‘struct hist_entry’)
util/hist.c:241:23: error: invalid type argument of ‘->’ (have ‘struct hist_entry’)
for this new code:
+ if (he->ms.map != entry->ms.map) {
+ he->ms.map = entry->ms.map;
+ if (he->ms.map)
+ he->ms.map->referenced = true;
+ }
because "entry" is a "struct hist_entry", not a pointer to a struct.
In mainline, "entry" is a pointer to struct passed as argument to the function.
So this is broken during backporting. But obviously not compile tested.
Signed-off-by: Zeev Tarantov <zeev.tarantov@gmail.com> Cc: Signed-off-by: David S. Miller <davem@davemloft.net> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Git commit 36409f6353fc2d7b6516e631415f938eadd92ffa "use generic RCU
page-table freeing code" introduced a tlb flushing bug. Partially revert
the above git commit and go back to s390 specific page table flush code.
For s390 the TLB can contain three types of entries, "normal" TLB
page-table entries, TLB combined region-and-segment-table (CRST) entries
and real-space entries. Linux does not use real-space entries which
leaves normal TLB entries and CRST entries. The CRST entries are
intermediate steps in the page-table translation called translation paths.
For example a 4K page access in a three-level page table setup will
create two CRST TLB entries and one page-table TLB entry. The advantage
of that approach is that a page access next to the previous one can reuse
the CRST entries and needs just a single read from memory to create the
page-table TLB entry. The disadvantage is that the TLB flushing rules are
more complicated, before any page-table may be freed the TLB needs to be
flushed.
In short: the generic RCU page-table freeing code is incorrect for the
CRST entries, in particular the check for mm_users < 2 is troublesome.
This is applicable to 3.0+ kernels.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the force changes went in back in 3.3.0, we ended up returning
disconnected in the !force case, and the connected in when forced,
as it hit the hardcoded check.
Fix it so all exits go via the hardcoded check and stop spurious
modesets on platforms with hardcoded EDIDs.
Reported-by: Evan McNabb (Red Hat) Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The check of the encoder type in the commit [e00e8b5e: drm/radeon/kms:
fix analog load detection on DVI-I connectors] is obviously wrong, and
it's the culprit of the regression on my workstation with DVI-analog
connection resulting in the blank output.
Fixed the typo now.
Signed-off-by: Takashi Iwai <tiwai@suse.de> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It was possible to extract the robust list head address from a setuid
process if it had used set_robust_list(), allowing an ASLR info leak. This
changes the permission checks to be the same as those used for similar
info that comes out of /proc.
Running a setuid program that uses robust futexes would have had:
cred->euid != pcred->euid
cred->euid == pcred->uid
so the old permissions check would allow it. I'm not aware of any setuid
programs that use robust futexes, so this is just a preventative measure.
(This patch is based on changes from grsecurity.)
Signed-off-by: Kees Cook <keescook@chromium.org> Cc: Darren Hart <dvhart@linux.intel.com> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Jiri Kosina <jkosina@suse.cz> Cc: Eric W. Biederman <ebiederm@xmission.com> Cc: David Howells <dhowells@redhat.com> Cc: Serge E. Hallyn <serge.hallyn@canonical.com> Cc: kernel-hardening@lists.openwall.com Cc: spender@grsecurity.net Link: http://lkml.kernel.org/r/20120319231253.GA20893@www.outflux.net Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Eran <eran@over-here.org> Tested-by: Michal Labedzki <michal.labedzki@tieto.com> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi> Cc: Jonathan Nieder <jrnieder@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a bitmap is added while the array is active, it is possible
for bitmap_daemon_work to run while the bitmap is being
initialised.
This is particularly a problem if bitmap_daemon_work sees
bitmap->filemap as non-NULL before it has been filled in properly.
So hold bitmap_info.mutex while filling in ->filemap
to prevent problems.
This patch is suitable for any -stable kernel, though it might not
apply cleanly before about 3.1.
Currently, Mode-Control register is accessed by read-modify-write.
According to DMA hardware specifications datasheet, prohibits this method.
Because this register resets to 0 by DMA HW after DMA transfer completes.
Thus, current read-modify-write processing can cause unexpected behavior.
The datasheet says in case of writing Mode-Control register, set the value for only target channel, the others must set '11b'.
e.g. Set DMA0=01b DMA11=10b
CTL0=33333331h
CTL2=00002333h
NOTE:
CTL0 includes DMA0~7 Mode-Control register.
CTL2 includes DMA8~11 Mode-Control register.
=================================
[ INFO: inconsistent lock state ]
2.6.39+ #89
---------------------------------
inconsistent {HARDIRQ-ON-W} -> {IN-HARDIRQ-W} usage.
rs232/822 [HC1[1]:SC0[0]:HE0:SE1] takes:
(&(&pd_chan->lock)->rlock){?.....}, at: [<c123b9a1>] pdc_desc_get+0x16/0xab
{HARDIRQ-ON-W} state was registered at:
[<c104fe28>] mark_irqflags+0xbd/0x11a
[<c1050386>] __lock_acquire+0x501/0x6bb
[<c1050945>] lock_acquire+0x63/0x7b
[<c131c51d>] _raw_spin_lock_bh+0x43/0x51
[<c123bee4>] pd_alloc_chan_resources+0x92/0x11e
[<c123ad62>] dma_chan_get+0x9b/0x107
[<c123b2d1>] __dma_request_channel+0x61/0xdc
[<c11ba24b>] pch_request_dma+0x61/0x19e
[<c11bb3b8>] pch_uart_startup+0x16a/0x1a2
[<c11b8446>] uart_startup+0x87/0x147
[<c11b9183>] uart_open+0x117/0x13e
[<c11a5c7d>] tty_open+0x23c/0x34c
[<c1097705>] chrdev_open+0x140/0x15f
[<c10930a6>] __dentry_open.clone.14+0x14a/0x22b
[<c1093dfb>] nameidata_to_filp+0x36/0x40
[<c109f28b>] do_last+0x513/0x635
[<c109f4af>] path_openat+0x9c/0x2aa
[<c109f6e4>] do_filp_open+0x27/0x69
[<c1093f02>] do_sys_open+0xfd/0x184
[<c1093fad>] sys_open+0x24/0x2a
[<c131d58c>] sysenter_do_call+0x12/0x32
irq event stamp: 2522
hardirqs last enabled at (2521): [<c131ca3b>] _raw_spin_unlock_irqrestore+0x36/0x52
hardirqs last disabled at (2522): [<c131db27>] common_interrupt+0x27/0x34
softirqs last enabled at (2354): [<c102fa11>] __do_softirq+0x10a/0x11a
softirqs last disabled at (2299): [<c10041a4>] do_softirq+0x57/0xa4
other info that might help us debug this:
2 locks held by rs232/822:
#0: (&tty->atomic_write_lock){+.+.+.}, at: [<c11a4b7a>] tty_write_lock+0x14/0x3c
#1: (&port_lock_key){-.....}, at: [<c11bad72>] pch_uart_interrupt+0x17/0x1e9
ISSUE: In case PCH_DMA with I2S communications with ch8~ch11, sometimes I2S data
is not send correctly.
CAUSE: The following patch I submitted before was not enough modification for
supporting DMA ch8~ch11. The modification for status register of ch8~11 was not
enough.
Currently, ".setup" function is not set.
As a result, when detecting our IOH's uart device without pch_uart, kernel panic
occurs at the following of pciserial_init_ports().
for (i = 0; i < nr_ports; i++) {
if (quirk->setup(priv, board, &serial_port, i))
break;
So, this patch adds the ".setup" function.
We can use pci_default_setup because our IOH's uart is compatible with 16550.
Add missing "personality.h"
security/commoncap.c: In function 'cap_bprm_set_creds':
security/commoncap.c:510: error: 'PER_CLEAR_ON_SETID' undeclared (first use in this function)
security/commoncap.c:510: error: (Each undeclared identifier is reported only once
security/commoncap.c:510: error: for each function it appears in.)
Signed-off-by: Jonghwan Choi <jhbird.choi@samsung.com> Acked-by: Serge Hallyn <serge.hallyn@canonical.com> Signed-off-by: James Morris <james.l.morris@oracle.com> Cc: Eric Paris <eparis@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For above ASL code, we need to save scope node(\_SB) to lookup
the argument node(\_SB.RAMB).
Reported-by: Jim Green <student.northwestern@gmail.com> Signed-off-by: Lin Ming <ming.m.lin@intel.com> Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Len Brown <len.brown@intel.com> Cc: Herton Ronaldo Krzesinski <herton.krzesinski@canonical.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ISSUE:
After a USB cable is connect/disconnected, the system rarely freezes.
CAUSE:
Since the USB device controller cannot know to disconnect the USB cable, when
it is used without detecting VBUS by GPIO, the UDC driver does not notify to
USB Gadget.
Since USB Gadget cannot know to disconnect, a false setting occurred when the
USB cable is connected/disconnect repeatedly.
ISSUE:
If the return value of pch_udc_pcd_init() is False, the return value of
this function is unsettled.
Since pch_udc_pcd_init() always returns 0, there is not actually the issue.
CAUSE:
If pch_udc_pcd_init() is True, the variable, retval, is not set for an
appropriate value.
Currently, external ROM access is enabled/disabled in probe()/remove().
So, when a buggy software access unanticipated memory area,
in case of enabling this ADE bit,
external ROM memory area can be broken.
This patch enables the ADE bit only accessing external ROM area.
Only ML7213/ML7223(Bus-n) has this register.
Currently,this driver doesn't care register "FUNCSEL" in suspend/resume.
This patch saves/restores FUNCSEL register only when the device is ML7213 or
ML7223(Bus-n).
Register "interrupt delay value" is for GbE which is connected to Bus-m of PCIe.
However currently, the value is set for Bus-n.
As a result, the value is not set correctly.
This patch moves setting the value processing of Bus-n to Bus-m.
Make sure hci_dev_open returns immediately if hci_dev_unregister has
been called.
This fixes a race between hci_dev_open and hci_dev_unregister which can
lead to a NULL-pointer dereference.
Bug is 100% reproducible using hciattach and a disconnected serial port:
0. # hciattach -n /dev/ttyO1 any noflow
1. hci_dev_open called from hci_power_on grabs req lock
2. hci_init_req executes but device fails to initialise (times out
eventually)
3. hci_dev_open is called from hci_sock_ioctl and sleeps on req lock
4. hci_uart_tty_close calls hci_dev_unregister and sleeps on req lock in
hci_dev_do_close
5. hci_dev_open (1) releases req lock
6. hci_dev_do_close grabs req lock and returns as device is not up
7. hci_dev_unregister sleeps in destroy_workqueue
8. hci_dev_open (3) grabs req lock, calls hci_init_req and eventually sleeps
9. hci_dev_unregister finishes, while hci_dev_open is still running...
The xHCI 1.0 spec errata released on June 13, 2011, changes the ordering
that the xHCI registers are saved and restored in. It moves the
interrupt pending (IMAN) and interrupt control (IMOD) registers to be
saved and restored last. I believe that's because the host controller
may attempt to fetch the event ring table when interrupts are
re-enabled. Therefore we need to restore the event ring registers
before we re-enable interrupts.
This should be backported to kernels as old as 2.6.37, that contain the
commit 5535b1d5f8885695c6ded783c692e3c0d0eda8ca "USB: xHCI: PCI power
management implementation"
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Tested-by: Elric Fu <elricfu1@gmail.com> Cc: Andiry Xu <andiry.xu@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the maximum noise floor limit is set as too high (-60dB). The
assumption of having a higher threshold limit is that it would help
de-sensitize the receiver (reduce phy errors) from continuous
interference. But when we have a bursty interference where there are
collisions and then free air time and if the receiver is desensitized too
much, it will miss the normal packets too. Lets make use of chips
specific min, nom and max limits always. This patch helps to improve the
connection stability in congested networks.
Cc: Paul Stewart <pstew@google.com> Tested-by: Gary Morain <gmorain@google.com> Signed-off-by: Madhan Jaganathan <madhanj@qca.qualcomm.com> Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
[bwh: Backported to 3.0/3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a process increases permissions using fcaps all of the dangerous
personality flags which are cleared for suid apps should also be cleared.
Thus programs given priviledge with fcaps will continue to have address space
randomization enabled even if the parent tried to disable it to make it
easier to attack.
Signed-off-by: Eric Paris <eparis@redhat.com> Reviewed-by: Serge Hallyn <serge.hallyn@canonical.com> Signed-off-by: James Morris <james.l.morris@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 360f748b204275229f8398cb2f9f53955db1503b
"serial: PL011: clear pending interrupts"
attempts to clear interrupts by writing to a
yet-unassigned memory address. This fixes the issue.
The breaking patch is marked for stable so should be
carried along with the other patch.
Cc: Shreshtha Kumar Sahu <shreshthakumar.sahu@stericsson.com> Cc: Russell King <linux@arm.linux.org.uk> Cc: Nicolas Pitre <nico@fluxnic.net> Reported-by: Viresh Kumar <viresh.kumar@st.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Tested-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Chanho Min reported that when the boot loader transfers
control to the kernel, there may be pending interrupts
causing the UART to lock up in an eternal loop trying to
pick tokens from the FIFO (since the RX interrupt flag
indicates there are tokens) while in practice there are
no tokens - in fact there is only a pending IRQ flag.
This patch address the issue with a combination of two
patches suggested by Russell King that clears and mask
all interrupts at probe() and clears any pending error
and RX interrupts at port startup time.
We suspect the spurious interrupts are a side-effect of
switching the UART from FIFO to non-FIFO mode.
Cc: Shreshtha Kumar Sahu <shreshthakumar.sahu@stericsson.com> Reported-by: Chanho Min <chanho0207@gmail.com> Suggested-by: Russell King <linux@arm.linux.org.uk> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Jong-Sung Kim <neidhard.kim@lge.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The suspend operation of VIA xHCI host have some issues and
hibernate operation works fine, so The XHCI_RESET_ON_RESUME
quirk is added for it.
This patch should base on "xHCI: Don't write zeroed pointer
to xHC registers" that is released by Sarah. Otherwise, the
host system error will ocurr in the hibernate operation
process.
This should be backported to stable kernels as old as 2.6.37,
that contain the commit c877b3b2ad5cb9d4fe523c5496185cc328ff3ae9
"xhci: Add reset on resume quirk for asrock p67 host".
Signed-off-by: Elric Fu <elricfu1@gmail.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Re-define XHCI_LEGACY_DISABLE_SMI and used it in right way. All SMI enable
bits will be cleared to zero and flag bits 29:31 are also cleared to zero.
Other bits should be presvered as Table 146.
This patch should be backported to kernels as old as 2.6.31.
Signed-off-by: Alex He <alex.he@amd.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The xhci_save_registers() function saved the event ring dequeue pointer
in the s3 register structure, but xhci_restore_registers() never
restored it. No other code in the xHCI successful resume path would
ever restore it either. Fix that.
This should be backported to kernels as old as 2.6.37, that contain the
commit 5535b1d5f8885695c6ded783c692e3c0d0eda8ca "USB: xHCI: PCI power
management implementation".
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Tested-by: Elric Fu <elricfu1@gmail.com> Cc: Andiry Xu <andiry.xu@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When xhci_mem_cleanup() is called, we can't be sure if the xHC is
actually halted. We can ask the xHC to halt by writing to the RUN bit
in the command register, but that might timeout due to a HW hang.
If the host controller is still running, we should not write zeroed
values to the event ring dequeue pointers or base tables, the DCBAA
pointers, or the command ring pointers. Eric Fu reports his VIA VL800
host accesses the event ring pointers after a failed register restore on
resume from suspend. The hypothesis is that the host never actually
halted before the register write to change the event ring pointer to
zero.
Remove all writes of zeroed values to pointer registers in
xhci_mem_cleanup(). Instead, make all callers of the function reset the
host controller first, which will reset those registers to zero.
xhci_mem_init() is the only caller that doesn't first halt and reset the
host controller before calling xhci_mem_cleanup().
This should be backported to kernels as old as 2.6.32.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Tested-by: Elric Fu <elricfu1@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While we're at that, define IMAN bitfield to aid readability.
The interrupt enable bit should be set once on driver init, and we
shouldn't need to continually re-enable it. Commit c21599a3 introduced
a read of the irq_pending register, and that allows us to preserve the
state of the IE bit. Before that commit, we were blindly writing 0x3 to
the register.
This patch should be backported to kernels as old as 2.6.36, or ones
that contain the commit c21599a36165dbc78b380846b254017a548b9de5 "USB:
xhci: Reduce reads and writes of interrupter registers".
Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1517b) fixes an error in the USB scatter-gather library.
The library code uses urb->dev to determine whether or nor an URB is
currently active; the completion handler sets urb->dev to NULL.
However the core unlinking routines need to use urb->dev. Since
unlinking always racing with completion, the completion handler must
not clear urb->dev -- it can lead to invalid memory accesses when a
transfer has to be cancelled.
This patch fixes the problem by getting rid of the lines that clear
urb->dev after urb has been submitted. As a result we may end up
trying to unlink an URB that failed in submission or that has already
completed, so an extra check is added after each unlink to avoid
printing an error message when this happens. The checks are updated
in both sg_complete() and sg_cancel(), and the second is updated to
match the first (currently it prints out unnecessary warning messages
if a device is unplugged while a transfer is in progress).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-and-tested-by: Illia Zaitsev <I.Zaitsev@adbglobal.com> CC: Ming Lei <tom.leiming@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / karo-tx-linux.git / log