Clemens Ladisch [Sun, 18 Mar 2012 18:01:39 +0000 (19:01 +0100)]
firewire: ohci: copy_iso_headers(): make comment match the code
The comment incorrectly talked about one little-endian quadlet, while
there are actually two. Furthermore, the endianness of the remaining
headers depends on whatever protocol is used, so don't mention them.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Clemens Ladisch [Mon, 12 Mar 2012 20:46:55 +0000 (21:46 +0100)]
firewire: cdev: fix IR multichannel event documentation
State more precisely when fw_cdev_event_iso_interrupt_mc is sent.
While the comment tried to reflect an amibuity in the OHCI
specification, there is only one method that is useful in practice,
and this also matches all the hardware implementations I've tested.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Clemens Ladisch [Mon, 12 Mar 2012 20:45:47 +0000 (21:45 +0100)]
firewire: ohci: fix too-early completion of IR multichannel buffers
handle_ir_buffer_fill() assumed that a completed descriptor would be
indicated by a non-zero transfer_status (as in most other descriptors).
However, this field is written by the controller as soon as (the end of)
the first packet has been written into the buffer. As a consequence, if
we happen to run into such a descriptor when the interrupt handler is
executed after such a packet has completed, the descriptor would be
taken out of the list of active descriptors as soon as the buffer had
been partially filled, so the event for the buffer being completely
filled would never be sent.
To fix this, handle descriptors only when they have been completely
filled, i.e., when res_count == 0. (This also matches the condition
that is reported by the controller with an interrupt.)
Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Cc: 2.6.36+ <stable@vger.kernel.org> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Stefan Richter [Sun, 4 Mar 2012 20:34:21 +0000 (21:34 +0100)]
firewire: ohci: move runtime debug facility out of #ifdef
CONFIG_FIREWIRE_OHCI_DEBUG could have been exposed to kernel tweakers
if CONFIG_EXPERT was set. But in hindsight, this stuff is far too
useful to omit it. So get rid of two #else branches that are only
going to bitrot otherwise.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Stefan Richter [Sun, 4 Mar 2012 13:24:31 +0000 (14:24 +0100)]
firewire: tone down some diagnostic log messages
The "skipped bus generations" message was added together with the
respective fw_device retaining/ reviving code in order to see how it all
works out. It did well, so don't spam the log anymore.
The "register access failure" situation still needs an actual handler.
But at this point it makes less sense to ask folks to send mails about
it. We now have a pretty good picture of what controllers emit this and
when:
Stefan Richter [Sun, 4 Mar 2012 13:23:00 +0000 (14:23 +0100)]
firewire: sbp2: replace a GFP_ATOMIC allocation
sbp2_send_management_orb() is called by sbp2_login, sbp2_reconnect, and
sbp2_remove, all which are able to sleep during memory allocations.
Actually, sbp2_send_management_orb() itself is a sleeping function.
Login and remove could allocate with GFP_KERNEL but reconnect needs
GFP_NOIO to ensure progress in low memory situations.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Chris Boot [Wed, 15 Feb 2012 14:59:10 +0000 (14:59 +0000)]
firewire: sbp2: Fix SCSI sense data mangling
SCSI sense data in SBP-2/3 is carried in an unusual format that means we
have to un-mangle it on our end before we pass it to the SCSI subsystem.
Currently our un-mangling code doesn't quite follow the SBP-2 standard
in that we always assume Current and never Deferred error types, we
never set the VALID bit, and we mishandle the FILEMARK, EOM and ILI
bits.
This patch fixes the sense un-mangling to correctly handle those and
follow the spec.
Signed-off-by: Chris Boot <bootc@bootc.net> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Chris Boot [Wed, 15 Feb 2012 14:59:09 +0000 (14:59 +0000)]
firewire: sbp2: Ignore SBP-2 targets on the local node
The firewire-sbp2 module tries to login to an SBP-2/3 target even when
it is running on the local node, which fails because of the inability to
fetch data from DMA mapped regions using firewire transactions on the
local node. It also doesn't make much sense to have the initiator and
target on the same node, so this patch prevents this behaviour.
Signed-off-by: Chris Boot <bootc@bootc.net> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (changed the comment)
Chris Boot [Wed, 15 Feb 2012 14:59:08 +0000 (14:59 +0000)]
firewire: sbp2: Take into account Unit_Unique_ID
If the target's unit directory contains a Unit_Unique_ID entry, we
should use that as the target's GUID for identification purposes. The
SBP-2 standards document says:
"Although the node unique ID (EUI-64) present in the bus information
block is sufficient to uniquely identify nodes attached to Serial Bus,
it is insufficient to identify a target when a vendor implements a
device with multiple Serial Bus node connections. In this case initiator
software requires information by which a particular target may be
uniquely identified, regardless of the Serial Bus access path used."
Stefan Richter [Sat, 18 Feb 2012 19:42:00 +0000 (20:42 +0100)]
firewire: core: convert AR-req handler lock from _irqsave to _bh
fw_core_handle_request() is called by the low-level driver in tasklet
context or process context, and fw_core_add/remove_address_handler() is
called by mid- or high-level code in process context. So convert
address_handler_lock accesses from those which disable local IRQs to
ones which just disable local softIRQs.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Stefan Richter [Sat, 18 Feb 2012 18:54:45 +0000 (19:54 +0100)]
firewire: core: fix race at address_handler unregistration
Fix the following unlikely but possible race:
CPU 1 CPU 2
------------------------------------------------------------------------
AR-request tasklet
lookup handler
unregister handler
free handler->callback_data or handler
call handler->callback
The application which registered the handler has no way to stop nodes
sending new requests to their address range, hence cannot prevent this
race.
Fix it simply by extending the address_handler_lock-protected region
from only around the lookup to around both lookup and call. We only
need to do so in the exclusive region handler; the FCP region handler
already holds the lock around the handler->callback call.
Alas this removes the current ability to execute the callback in
parallel on different CPUs if it was called for different FireWire cards
at the same time. (For a single card, the handler is already
serialized.) If this loss of a rather obscure feature is not tolerable,
a more complex fix would be required: Add a handler reference counter;
wait in fw_core_remove_address_handler() for this conter to become zero.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Stefan Richter [Sat, 18 Feb 2012 18:53:39 +0000 (19:53 +0100)]
firewire: core: remove obsolete comment
Target-like applications or peer-to-peer-like applications require the
global address handler registration which we have right now, or a per-
card registration. And node lookup, while it would be nice to have,
would be impossible in the brief time between self-ID-complete event and
completion of firewire-core's topology scanning.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Stefan Richter [Sat, 18 Feb 2012 21:03:14 +0000 (22:03 +0100)]
firewire: core: prefix log messages with card name
Associate all log messages from firewire-core with the respective card
because some people have more than one card. E.g.
firewire_ohci 0000:04:00.0: added OHCI v1.10 device as card 0, 8 IR + 8 IT contexts, quirks 0x0
firewire_ohci 0000:05:00.0: added OHCI v1.10 device as card 1, 8 IR + 8 IT contexts, quirks 0x0
firewire_core: created device fw0: GUID 0814438400000389, S800
firewire_core: phy config: new root=ffc1, gap_count=5
firewire_core: created device fw1: GUID 0814438400000388, S800
firewire_core: created device fw2: GUID 0001d202e06800d1, S800
turns into
firewire_ohci 0000:04:00.0: added OHCI v1.10 device as card 0, 8 IR + 8 IT contexts, quirks 0x0
firewire_ohci 0000:05:00.0: added OHCI v1.10 device as card 1, 8 IR + 8 IT contexts, quirks 0x0
firewire_core 0000:04:00.0: created device fw0: GUID 0814438400000389, S800
firewire_core 0000:04:00.0: phy config: new root=ffc1, gap_count=5
firewire_core 0000:05:00.0: created device fw1: GUID 0814438400000388, S800
firewire_core 0000:04:00.0: created device fw2: GUID 0001d202e06800d1, S800
This increases the module size slightly; to keep this in check, turn the
former printk wrapper macros into functions. Their implementation is
largely copied from driver core's dev_printk counterparts.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Stefan Richter [Sun, 19 Feb 2012 11:48:36 +0000 (12:48 +0100)]
firewire: net: use dev_printk API
Change the log line prefix from "firewire_net: " to "net firewire0: "
etc. for the case that several RFC 2734 interfaces are being used in the
same machine.
Note, the netdev_printk API is not very useful to firewire-net.
netdev_notice(net, "abc\n") would result in irritating messages like
"firewire_ohci 0000:0a:00.0: firewire0: abc". Nor would a dev_printk on
the fw_unit.device to which firewire-net is being bound be useful,
because there are generally multiple ones of those per interface (from
all RFC 2734 peers on the bus, the local node being only one of them).
In the initialization message of each interface, log the PCI device
name of the card which is parent of the netdevice instead of the GUID
of the peer which was semi-randomly used to establish the netdevice.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Stefan Richter [Sat, 18 Feb 2012 21:01:54 +0000 (22:01 +0100)]
firewire: net: identify to driver core as "firewire_net", not "net"
On second thought, there is little reason to have driver name differ
from module name. Therefore, change
/sys/bus/firewire/drivers/net
/sys/bus/firewire/devices/fw0.0/driver -> [...]/net
/sys/module/firewire_net/drivers/firewire:net
to
/sys/bus/firewire/drivers/firewire_net
/sys/bus/firewire/devices/fw0.0/driver -> [...]/firewire_net
/sys/module/firewire_net/drivers/firewire:firewire_net
It is redundant but consistent with firewire-sbp2's recently changed
driver name.
I don't see this anywhere used, so it should not matter either way.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Stefan Richter [Sat, 18 Feb 2012 21:01:14 +0000 (22:01 +0100)]
firewire: sbp2: identify to driver core as "firewire_sbp2", not "sbp2"
Commit eba9ebaaa26d "firewire: sbp2: use dev_printk API" changed
messages from e.g.
firewire_sbp2: fw3.0: logged in to LUN 0000 (0 retries)
to
sbp2 fw3.0: logged in to LUN 0000 (0 retries)
because the driver calls itself as "sbp2" when registering with driver
core and with SCSI core. This is of course confusing, so switch to the
name "firewire_sbp2" for driver core in order to match what lsmod and
/sys/module/ show. So we are back to
firewire_sbp2 fw3.0: logged in to LUN 0000 (0 retries)
in the kernel log.
This also changes
/sys/bus/firewire/drivers/sbp2
/sys/bus/firewire/devices/fw3.0/driver -> [...]/sbp2
/sys/module/firewire_sbp2/drivers/firewire:sbp2
to
/sys/bus/firewire/drivers/firewire_sbp2
/sys/bus/firewire/devices/fw3.0/driver -> [...]/firewire_sbp2
/sys/module/firewire_sbp2/drivers/firewire:firewire_sbp2
but "cat /sys/class/scsi_host/host27/proc_name" stays "sbp2" just in
case that proc_name is used by any userland.
The transport detection in lsscsi is not affected. (Tested with lsscsi
version 0.25.) Udev's /dev/disk/by-id and by-path symlinks are not
affected either.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Stefan Richter [Sat, 27 Aug 2011 16:53:03 +0000 (18:53 +0200)]
firewire: move fw_device reference counting from drivers to core
fw_unit device drivers invariably need to talk to the fw_unit's parent
(an fw_device) and grandparent (an fw_card). firewire-core already
maintains an fw_card reference for the entire lifetime of an fw_device.
Likewise, let firewire-core maintain an fw_device reference for the
entire lifetime of an fw_unit so that fw_unit drivers don't have to.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Clemens Ladisch [Sat, 15 Oct 2011 16:14:39 +0000 (18:14 +0200)]
firewire: ohci: work around selfID junk due to wrong gap count
If a device's firmware initiates a bus reset by setting the IBR bit in
PHY register 1 without resetting the gap count field to 63 (and without
having sent a PHY configuration packet beforehand), the gap count of
this node will remain at the old value after the bus reset and thus be
inconsistent with the gap count on all other nodes.
The bus manager is supposed to detect the inconsistent gap count values
in the self ID packets and correct them by issuing another bus reset.
However, if the buggy device happens to be the cycle master, and if it
sends a cycle start packet immediately after the bus reset (which is
likely after a long bus reset), then the time between the end of the
selfID phase and the start of the cycle start packet will be based on
the too-small gap count value, so this gap will be too short to be
detected as a subaction gap by the other nodes. This means that the
cycle start packet will be assumed to be self ID data, and will be
stored after the actual self ID quadlets in the self ID buffer.
This garbage in the self ID buffer made firewire-core ignore all of the
self ID data, and thus prevented the Linux bus manager from correcting
the problem. Furthermore, because the bus reset handling was aborted
completely, asynchronous transfers would be no longer handled correctly,
and fw_run_transaction() would hang until the next bus reset.
To fix this, make the detection of inconsistent self IDs more
discriminating: If the invalid data in the self ID buffer looks like
a cycle start packet, we can assume that the previous data in the buffer
is correctly received self ID information, and process it normally.
(We inspect only the first quadlet of the cycle start packet, because
this value is different enough from any valid self ID quadlet, and many
controllers do not store the cycle start packet in five quadlets because
they expect self ID data to have an even number of quadlets.)
This bug has been observed when a bus-powered DesktopKonnekt6 is
switched off with its power button.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Stephan Gatzka [Mon, 26 Sep 2011 19:44:30 +0000 (21:44 +0200)]
firewire: net: Use posted writes
Change memory region to ohci "middle address space". This effectively
reduces the number of packets by 50%.
[Stefan R.:] This eliminates 1394 ack packets and improved throughput
by a few percent in some tests with an S400a connection with and without
gap count optimization. Since firewire-net taxes the AR-req DMA unit of
a FireWire controller much more than firewire-sbp2 (which uses the
middle address space with PCI posted writes too), this commit also
changes a related error printk into a ratelimited one as a precaution.
Side note: The IPv4-over-1394 drivers of Mac OS X 10.4, Windows XP SP3,
and the Thesycon 1394 bus driver for Windows all use the middle address
space too.
Signed-off-by: Stephan Gatzka <stephan@gatzka.org> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Stefan Richter [Mon, 19 Sep 2011 07:29:30 +0000 (09:29 +0200)]
firewire: ohci: optimize TSB41BA3D detection
Takes less source code and machine code, and less runtime with PHYs
other than TSB41BA3D (e.g. TSB81BA3 with device ID 0x831304 which takes
one instead of six read_paged_phy_reg now).
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Stephan Gatzka [Mon, 12 Sep 2011 20:23:53 +0000 (22:23 +0200)]
firewire: ohci: Add support for TSB41BA3D phy
This patch implements a work around for the Texas Instruments PHY
TSB41BA3D. This phy has a bug at least in combination with the TI LLCs
TSB82AA2B and TSB12LV26. The selfid coming from the locally connected
phy is not propagated into the selfid buffer of the OHCI (see
http://www.ti.com/litv/pdf/sllz059 for details). The main idea is to
construct the selfid ourselves.
Signed-off-by: Stephan Gatzka <stephan@gatzka.org> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Stephan Gatzka [Mon, 25 Jul 2011 20:16:24 +0000 (22:16 +0200)]
firewire: ohci: Move code from the bus reset tasklet into a workqueue
Code inside bus_reset_work may now sleep. This is a prerequisite to
support a phy from Texas Instruments cleanly. The patch to support this
phy will be submitted later.
Signed-off-by: Stephan Gatzka <stephan@gatzka.org> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Stefan Richter [Sat, 27 Aug 2011 13:35:23 +0000 (15:35 +0200)]
firewire: sbp2: fold two functions into one
sbp2_release_target() is folded into its primary user, sbp2_remove().
The only other caller, a failure path in sbp2_probe(), now uses
sbp2_remove(). This adds unnecessary cancel_delayed_work_sync() calls
to that failure path but results in less code and text.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Stefan Richter [Sat, 27 Aug 2011 13:34:32 +0000 (15:34 +0200)]
firewire: sbp2: move some code to more sensible places
Implement sbp2_queue_work(), which is now a very simple accessor to one
of the struct sbp2_logical_unit members, right after the definition of
struct sbp2_logical_unit.
Put the sbp2_reconnect() implementation right after the sbp2_login()
implementation. They are both part of the SBP-2 access protocol.
Implement the driver methods sbp2_probe(), spp2_update(), sbp2_remove()
in this order, reflecting the lifetime of an SBP-2 target.
Place the sbp2_release_target() implementation right next to
sbp2_remove() which is its primary user, and after sbp2_probe() which is
the counterpart to sbp2_release_target().
There are no changes to the implementations here, or at least not meant
to be.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Since commit 0278ccd9d53e07c4e699432b2fed9de6c56f506c "firewire: sbp2:
fix panic after rmmod with slow targets", the lifetime of an sbp2_target
instance does no longer extent past the return of sbp2_remove().
Therefore it is no longer necessary to call fw_unit_get/put() and
fw_device_get/put() in sbp2_probe/remove().
Furthermore, said commit also ensures that lu->work is not going to be
executed or requeued at a time when the sbp2_target is no longer in use.
Hence there is no need for sbp2_target reference counting for lu->work.
Other concurrent contexts:
- Processes which access the sysfs of the SCSI host device or of one
of its subdevices are safe because these interfaces are all removed
by scsi_remove_device/host() in sbp2_release_target().
- SBP-2 command block ORB transactions are finished when
scsi_remove_device() in sbp2_release_target() returns.
- SBP-2 management ORB transactions are finished when
cancel_delayed_work_sync(&lu->work) before sbp2_release_target()
returns.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Ming Lei [Wed, 31 Aug 2011 02:45:46 +0000 (10:45 +0800)]
firewire: ohci: add no MSI quirk for O2Micro controller
This fixes https://bugs.launchpad.net/ubuntu/+source/linux/+bug/801719 .
An O2Micro PCI Express FireWire controller,
"FireWire (IEEE 1394) [0c00]: O2 Micro, Inc. Device [1217:11f7] (rev 05)"
which is a combination device together with an SDHCI controller and some
sort of storage controller, misses SBP-2 status writes from an attached
FireWire HDD. This problem goes away if MSI is disabled for this
FireWire controller.
The device reportedly does not require QUIRK_CYCLE_TIMER.
Signed-off-by: Ming Lei <ming.lei@canonical.com> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (amended changelog) Cc: <stable@kernel.org>
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm: Remove duplicate "return" statement
drm/nv04/crtc: Bail out if FB is not bound to crtc
drm/nouveau: fix nv04_sgdma_bind on non-"4kB pages" archs
drm/nouveau: properly handle allocation failure in nouveau_sgdma_populate
drm/nouveau: fix oops on pre-semaphore hardware
drm/nv50/crtc: Bail out if FB is not bound to crtc
drm/radeon/kms: fix DP detect and EDID fetch for DP bridges
Merge branch 'fixes' of git://git.linaro.org/people/arnd/arm-soc
* 'fixes' of git://git.linaro.org/people/arnd/arm-soc:
ARM: CSR: add missing sentinels to of_device_id tables
ARM: cns3xxx: Fix newly introduced warnings in the PCIe code
ARM: cns3xxx: Fix compile error caused by hardware.h removed
ARM: davinci: fix cache flush build error
ARM: davinci: correct MDSTAT_STATE_MASK
ARM: davinci: da850 EVM: read mac address from SPI flash
OMAP: omap_device: fix !CONFIG_SUSPEND case in _noirq handlers
OMAP2430: hwmod: musb: add missing terminator to omap2430_usbhsotg_addrs[]
OMAP3: clock: indicate that gpt12_fck and wdt1_fck are in the WKUP clockdomain
OMAP4: clock: fix compile warning
OMAP4: clock: re-enable previous clockdomain enable/disable sequence
OMAP: clockdomain: Wait for powerdomain to be ON when using clockdomain force wakeup
OMAP: powerdomains: Make all powerdomain target states as ON at init
The LTTng 2.0 kernel tracer (stand-alone module package, available at
http://lttng.org) uses the 0xF6 ioctl range for tracer control and
transport operations.
Merge branch 'for-linus' of git://github.com/chrismason/linux
* 'for-linus' of git://github.com/chrismason/linux:
Btrfs: add dummy extent if dst offset excceeds file end in
Btrfs: calc file extent num_bytes correctly in file clone
btrfs: xattr: fix attribute removal
Btrfs: fix wrong nbytes information of the inode
Btrfs: fix the file extent gap when doing direct IO
Btrfs: fix unclosed transaction handle in btrfs_cont_expand
Btrfs: fix misuse of trans block rsv
Btrfs: reset to appropriate block rsv after orphan operations
Btrfs: skip locking if searching the commit root in csum lookup
btrfs: fix warning in iput for bad-inode
Btrfs: fix an oops when deleting snapshots
If we write some data into the data hole of the file(no preallocation for this
hole), Btrfs will allocate some disk space, and update nbytes of the inode, but
the other element--disk_i_size needn't be updated. At this condition, we must
update inode metadata though disk_i_size is not changed(btrfs_ordered_update_i_size()
return 1).
Btrfs: fix the file extent gap when doing direct IO
When we write some data to the place that is beyond the end of the file
in direct I/O mode, a data hole will be created. And Btrfs should insert
a file extent item that point to this hole into the fs tree. But unfortunately
Btrfs forgets doing it.
The following is a simple way to reproduce it:
# mkfs.btrfs /dev/sdc2
# mount /dev/sdc2 /test4
# touch /test4/a
# dd if=/dev/zero of=/test4/a seek=8 count=1 bs=4K oflag=direct conv=nocreat,notrunc
# umount /test4
# btrfsck /dev/sdc2
root 5 inode 257 errors 100
Liu Bo [Sun, 11 Sep 2011 14:52:24 +0000 (10:52 -0400)]
Btrfs: fix misuse of trans block rsv
At the beginning of create_pending_snapshot, trans->block_rsv is set
to pending->block_rsv and is used for snapshot things, however, when
it is done, we do not recover it as will.
Signed-off-by: Liu Bo <liubo2009@cn.fujitsu.com> Signed-off-by: Chris Mason <chris.mason@oracle.com>
Liu Bo [Sun, 11 Sep 2011 14:52:24 +0000 (10:52 -0400)]
Btrfs: reset to appropriate block rsv after orphan operations
While truncating free space cache, we forget to change trans->block_rsv
back to the original one, but leave it with the orphan_block_rsv, and
then with option inode_cache enable, it leads to countless warnings of
btrfs_alloc_free_block and btrfs_orphan_commit_root:
WARNING: at fs/btrfs/extent-tree.c:5711 btrfs_alloc_free_block+0x180/0x350 [btrfs]()
...
WARNING: at fs/btrfs/inode.c:2193 btrfs_orphan_commit_root+0xb0/0xc0 [btrfs]()
Signed-off-by: Liu Bo <liubo2009@cn.fujitsu.com> Signed-off-by: Chris Mason <chris.mason@oracle.com>
Josef Bacik [Sun, 11 Sep 2011 14:52:24 +0000 (10:52 -0400)]
Btrfs: skip locking if searching the commit root in csum lookup
It's not enough to just search the commit root, since we could be cow'ing the
very block we need to search through, which would mean that its locked and we'll
still deadlock. So use path->skip_locking as well. Thanks,
Signed-off-by: Josef Bacik <josef@redhat.com> Signed-off-by: Chris Mason <chris.mason@oracle.com>
Signed-off-by: Sergei Trofimovich <slyfox@gentoo.org> CC: Konstantin Khlebnikov <khlebnikov@openvz.org> Tested-by: David Sterba <dsterba@suse.cz> CC: Josef Bacik <josef@redhat.com> CC: Chris Mason <chris.mason@oracle.com> Signed-off-by: Chris Mason <chris.mason@oracle.com>
When it comes to btrfs_lookup_dentry, we may set a snapshot's inode->i_ino
to BTRFS_EMPTY_SUBVOL_DIR_OBJECTID instead of BTRFS_FIRST_FREE_OBJECTID,
while the snapshot's location.objectid remains unchanged.
However, btrfs_ino() does not take this into account, and returns a wrong ino,
and causes the oops.
Signed-off-by: Liu Bo <liubo2009@cn.fujitsu.com> Signed-off-by: Chris Mason <chris.mason@oracle.com>
Florian Mickler [Wed, 10 Aug 2011 10:05:20 +0000 (07:05 -0300)]
[media] vp7045: fix buffer setup
dvb_usb_device_init calls the frontend_attach method of this driver which
uses vp7045_usb_ob. In order to have a buffer ready in vp7045_usb_op, it has to
be allocated before that happens.
Luckily we can use the whole private data as the buffer as it gets separately
allocated on the heap via kzalloc in dvb_usb_device_init and is thus apt for
use via usb_control_msg.
This fixes a
BUG: unable to handle kernel paging request at 0000000000001e78
reported by Tino Keitel and diagnosed by Dan Carpenter.
Cc: stable@kernel.org # For v3.0 and upper Tested-by: Tino Keitel <tino.keitel@tikei.de> Signed-off-by: Florian Mickler <florian@mickler.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jarod Wilson [Mon, 8 Aug 2011 20:20:40 +0000 (17:20 -0300)]
[media] nuvoton-cir: simplify raw IR sample handling
The nuvoton-cir driver was storing up consecutive pulse-pulse and
space-space samples internally, for no good reason, since
ir_raw_event_store_with_filter() already merges back to back like
samples types for us. This should also fix a regression introduced late
in 3.0 that related to a timeout change, which actually becomes correct
when coupled with this change. Tested with RC6 and RC5 on my own
nuvoton-cir hardware atop vanilla 3.0.0, after verifying quirky
behavior in 3.0 due to the timeout change.
Reported-by: Stephan Raue <sraue@openelec.tv> CC: Stephan Raue <sraue@openelec.tv> CC: stable@vger.kernel.org Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jesper Juhl [Mon, 1 Aug 2011 21:39:17 +0000 (18:39 -0300)]
[media] [Resend] viacam: Don't explode if pci_find_bus() returns NULL
In the unlikely case that pci_find_bus() should return NULL
viacam_serial_is_enabled() is going to dereference a NULL pointer and
blow up. Better safe than sorry, so be defensive and check the
pointer.
Dan Carpenter [Sat, 23 Jul 2011 18:53:03 +0000 (15:53 -0300)]
[media] pwc: precedence bug in pwc_init_controls()
'!' has higher precedence than '&' so we need parenthesis here.
Signed-off-by: Dan Carpenter <error27@gmail.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jonas Bonn [Mon, 5 Sep 2011 11:47:10 +0000 (13:47 +0200)]
Add missing DMA ops
For the initial architecture submission, not all of the DMA ops were
implemented. This patch adds the *map_page and *map_sg variants of the
DMA mapping ops.
This patch is currently of interest mainly to some drivers that haven't
been submitted upstream yet.
Merge branch 'fixes' of http://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm
* 'fixes' of http://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm:
ARM: 7088/1: entry: fix wrong parameter name used in do_thumb_abort
ARM: 7080/1: l2x0: make sure I&D are not locked down on init
ARM: 7081/1: mach-integrator: fix the clocksource
NET: am79c961: fix race in link status code
ARM: 7067/1: mm: keep significant bits in pfn_valid
ARM: 7088/1: entry: fix wrong parameter name used in do_thumb_abort
Commit be020f8618ca, "ARM: entry: abort-macro: specify registers to be
used for macros", while replacing register numbers with macro parameter
names, mismatched the name used for r1. For me, this resulted in user
space built for EABI with -march=armv4t -mtune=arm920t -mthumb-interwork
-mthumb broken on my OMAP1510 based Amstrad Delta (old ABI and no thumb
still worked for me though).
Fix this by using correct parameter name fsr instead of mismatched psr,
used by callers for another purpose.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since backlight_types[] isn't modified, let's declare it const. That
was probably the intention of the author of commit bb7ca747f8d6
("backlight: add backlight type"), via which the "const char const *"
construct was introduced. The duplicate const was detected by sparse.
Signed-off-by: Bart Van Assche <bvanassche@acm.org> Cc: Matthew Garrett <mjg@redhat.com> Cc: Richard Purdie <rpurdie@rpsys.net> Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge branch 'for-linus' of git://neil.brown.name/md
* 'for-linus' of git://neil.brown.name/md:
md: Fix handling for devices from 2TB to 4TB in 0.90 metadata.
md/raid1,10: Remove use-after-free bug in make_request.
md/raid10: unify handling of write completion.
Avoid dereferencing a 'request_queue' after last close.
md: Fix handling for devices from 2TB to 4TB in 0.90 metadata.
0.90 metadata uses an unsigned 32bit number to count the number of
kilobytes used from each device.
This should allow up to 4TB per device.
However we multiply this by 2 (to get sectors) before casting to a
larger type, so sizes above 2TB get truncated.
Also we allow rdev->sectors to be larger than 4TB, so it is possible
for the array to be resized larger than the metadata can handle.
So make sure rdev->sectors never exceeds 4TB when 0.90 metadata is in
used.
Also the sanity check at the end of super_90_load should include level
1 as it used ->size too. (RAID0 and Linear don't use ->size at all).
A write can complete at two different places:
1/ when the last member-device write completes, through
raid10_end_write_request
2/ in make_request() when we remove the initial bias from ->remaining.
These two should do exactly the same thing and the comment says they
do, but they don't.
So factor the correct code out into a function and call it in both
places. This makes the code much more similar to RAID1.
The difference is only significant if there is an error, and they
usually take a while, so it is unlikely that there will be an error
already when make_request is completing, so this is unlikely to cause
real problems.
Avoid dereferencing a 'request_queue' after last close.
On the last close of an 'md' device which as been stopped, the device
is destroyed and in particular the request_queue is freed. The free
is done in a separate thread so it might happen a short time later.
__blkdev_put calls bdev_inode_switch_bdi *after* ->release has been
called.
Since commit f758eeabeb96f878c860e8f110f94ec8820822a9
bdev_inode_switch_bdi will dereference the 'old' bdi, which lives
inside a request_queue, to get a spin lock. This causes the last
close on an md device to sometime take a spin_lock which lives in
freed memory - which results in an oops.
So move the called to bdev_inode_switch_bdi before the call to
->release.
Jon Mason [Thu, 8 Sep 2011 21:41:18 +0000 (16:41 -0500)]
PCI: Remove MRRS modification from MPS setting code
Modifying the Maximum Read Request Size to 0 (value of 128Bytes) has
massive negative ramifications on some devices. Without knowing which
devices have this issue, do not modify from the default value when
walking the PCI-E bus in pcie_bus_safe mode. Also, make pcie_bus_safe
the default procedure.
Tested-by: Sven Schnelle <svens@stackframe.org> Tested-by: Simon Kirby <sim@hostway.ca> Tested-by: Stephen M. Cameron <scameron@beardog.cce.hp.com> Reported-and-tested-by: Eric Dumazet <eric.dumazet@gmail.com> Reported-and-tested-by: Niels Ole Salscheider <niels_ole@salscheider-online.de>
References: https://bugzilla.kernel.org/show_bug.cgi?id=42162 Signed-off-by: Jon Mason <mason@myri.com> Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix pointer dereference before call to pcie_bus_configure_settings
Commit b03e7495a862 ("PCI: Set PCI-E Max Payload Size on fabric")
introduced a potential NULL pointer dereference in calls to
pcie_bus_configure_settings due to attempts to access pci_bus self
variables when the self pointer is NULL.
To correct this, verify that the self pointer in pci_bus is non-NULL
before dereferencing it.
Merge branch 'for-linus' of git://dev.laptop.org/users/cjb/mmc
* 'for-linus' of git://dev.laptop.org/users/cjb/mmc:
mmc: sdhci-s3c: Fix mmc card I/O problem
mmc: sd: UHS-I bus speed should be set last in UHS initialization
mmc: sdhi: initialise mmc_data->flags before use
mmc: core: use non-reentrant workqueue for clock gating
mmc: core: prevent aggressive clock gating racing with ios updates
mmc: rename mmc_host_clk_{ungate|gate} to mmc_host_clk_{hold|release}
mmc: sdhci-esdhc-imx: add missing inclusion of linux/module.h
Prior to 2.6.38 automount would not trigger on either stat(2) or
lstat(2) on the automount point.
After 2.6.38, with the introduction of the ->d_automount()
infrastructure, stat(2) and others would start triggering automount
while lstat(2), etc. still would not. This is a regression and a
userspace ABI change.
It appears that there was an attempt at fixing various userspace tools
to not trigger the automount. But since the stat system call is
rather common it is impossible to "fix" all userspace.
This patch reverts the original behavior, which is to not trigger on
stat(2) and other symlink following syscalls.
[ It's not really clear what the right behavior is. Apparently Solaris
does the "automount on stat, leave alone on lstat". And some programs
can get unhappy when "stat+open+fstat" ends up giving a different
result from the fstat than from the initial stat.
But the change in 2.6.38 resulted in problems for some people, so
we're going back to old behavior. Maybe we can re-visit this
discussion at some future date - Linus ]
Reported-by: Leonardo Chiquitto <leonardo.lists@gmail.com> Signed-off-by: Miklos Szeredi <mszeredi@suse.cz> Acked-by: Ian Kent <raven@themaw.net> Cc: David Howells <dhowells@redhat.com> Cc: stable@kernel.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Anton Vorontsov [Fri, 9 Sep 2011 19:18:00 +0000 (23:18 +0400)]
ARM: cns3xxx: Fix newly introduced warnings in the PCIe code
commit d5341942d784134f2997b3ff82cd63cf71d1f932 ("PCI: Make the struct
pci_dev * argument of pci_fixup_irqs const") did not change argument
of pdev_to_cnspci(), and thus introduced the following warnings:
CHECK arch/arm/mach-cns3xxx/pcie.c
pcie.c:177:60: warning: incorrect type in argument 1 (different modifiers)
pcie.c:177:60: expected struct pci_dev *dev
pcie.c:177:60: got struct pci_dev const *dev
CC arch/arm/mach-cns3xxx/pcie.o
pcie.c: In function 'cns3xxx_pcie_map_irq':
pcie.c:177: warning: passing argument 1 of 'pdev_to_cnspci' discards qualifiers from pointer target type
pcie.c:52: note: expected 'struct pci_dev *' but argument is of type 'const struct pci_dev *'
This patch fixes the issue.
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Tommy Lin [Thu, 28 Jul 2011 17:14:46 +0000 (01:14 +0800)]
ARM: cns3xxx: Fix compile error caused by hardware.h removed
Commit c9d95fbe59e426eed7f16e7cac812e46ac4772d0 "ARM: convert PCI defines
to variables" deleted cns3xxx' hardware.h, but didn't remove references
for it, so do it now.
This patch removes lines that refer to hardware.h.
Signed-off-by: Tommy Lin <tommy.lin.1101@gmail.com> Signed-off-by: Imre Kaloz <kaloz@openwrt.org> Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Dave Airlie [Fri, 9 Sep 2011 08:10:04 +0000 (09:10 +0100)]
Merge branch 'drm-nouveau-fixes' of git://anongit.freedesktop.org/git/nouveau/linux-2.6 into drm-test
* 'drm-nouveau-fixes' of git://anongit.freedesktop.org/git/nouveau/linux-2.6:
drm/nv04/crtc: Bail out if FB is not bound to crtc
drm/nouveau: fix nv04_sgdma_bind on non-"4kB pages" archs
drm/nouveau: properly handle allocation failure in nouveau_sgdma_populate
drm/nouveau: fix oops on pre-semaphore hardware
drm/nv50/crtc: Bail out if FB is not bound to crtc
Marcin Slusarz [Mon, 22 Aug 2011 21:14:05 +0000 (23:14 +0200)]
drm/nouveau: properly handle allocation failure in nouveau_sgdma_populate
Not cleaning after alloc failure would result in crash on destroy,
because nouveau_sgdma_clear assumes "ttm_alloced" to be not null when
"pages" is not null.
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com> Cc: stable@kernel.org Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Merge branch 'fixes' of git://git.infradead.org/users/vkoul/slave-dma
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine/ste_dma40: fix memory leak due to prepared descriptors
dmaengine/ste_dma40: fix Oops due to double free of client descriptor
dmaengine/ste_dma40: remove duplicate call to d40_pool_lli_free().
dmaengine/ste_dma40: add missing kernel doc for pending_queue
Merge branch 'for-linus' of git://twin.jikos.cz/jikos/hid
* 'for-linus' of git://twin.jikos.cz/jikos/hid:
HID: wacom: Unregister sysfs attributes on remove
HID: wacom: Fix error path of power-supply initialization
HID: add support for HuiJia USB Gamepad connector
HID: magicmouse: ignore 'ivalid report id' while switching modes, v2
HID: magicmouse: Set resolution of touch surfaces
Merge branch 'amd/fixes' of git://git.8bytes.org/scm/iommu
* 'amd/fixes' of git://git.8bytes.org/scm/iommu:
iommu/amd: Don't take domain->lock recursivly
iommu/amd: Make sure iommu->need_sync contains correct value
Randy Dunlap [Thu, 8 Sep 2011 17:16:47 +0000 (10:16 -0700)]
regulator: fix kernel-doc warning in consumer.h
Fix kernel-doc warning about internal/private data by marking it
as "private:" so that kernel-doc will ignore it.
Warning(include/linux/regulator/consumer.h:128): No description found for parameter 'ret'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge branch 'timers-fixes-for-linus' of git://tesla.tglx.de/git/linux-2.6-tip
* 'timers-fixes-for-linus' of git://tesla.tglx.de/git/linux-2.6-tip:
rtc: twl: Fix registration vs. init order
rtc: Initialized rtc_time->tm_isdst
rtc: Fix RTC PIE frequency limit
rtc: rtc-twl: Remove lockdep related local_irq_enable()
rtc: rtc-twl: Switch to using threaded irq
rtc: ep93xx: Fix 'rtc' may be used uninitialized warning
alarmtimers: Avoid possible denial of service with high freq periodic timers
alarmtimers: Memset itimerspec passed into alarm_timer_get
alarmtimers: Avoid possible null pointer traversal
Merge branch 'sched-fixes-for-linus' of git://tesla.tglx.de/git/linux-2.6-tip
* 'sched-fixes-for-linus' of git://tesla.tglx.de/git/linux-2.6-tip:
sched: Fix a memory leak in __sdt_free()
sched: Move blk_schedule_flush_plug() out of __schedule()
sched: Separate the scheduler entry for preemption
Merge branch 'perf-fixes-for-linus' of git://tesla.tglx.de/git/linux-2.6-tip
* 'perf-fixes-for-linus' of git://tesla.tglx.de/git/linux-2.6-tip:
x86, perf: Check that current->mm is alive before getting user callchain
perf_event: Fix broken calc_timer_values()
perf events: Fix slow and broken cgroup context switch code
projects / linux-beck.git / log