Duncan Laurie [Sun, 17 Mar 2013 21:56:39 +0000 (14:56 -0700)]
TPM: Retry SaveState command in suspend path
If the TPM has already been sent a SaveState command before the driver
is loaded it may have problems sending that same command again later.
This issue is seen with the Chromebook Pixel due to a firmware bug in
the legacy mode boot path which is sending the SaveState command
before booting the kernel. More information is available at
http://crbug.com/203524
This change introduces a retry of the SaveState command in the suspend
path in order to work around this issue. A future firmware update
should fix this but this is also a trivial workaround in the driver
that has no effect on systems that do not show this problem.
When this does happen the TPM responds with a non-fatal TPM_RETRY code
that is defined in the specification:
The TPM is too busy to respond to the command immediately, but the
command could be resubmitted at a later time. The TPM MAY return
TPM_RETRY for any command at any time.
It can take several seconds before the TPM will respond again. I
measured a typical time between 3 and 4 seconds and the timeout is set
at a safe 5 seconds.
It is also possible to reproduce this with commands via /dev/tpm0.
The bug linked above has a python script attached which can be used to
test for this problem. I tested a variety of TPMs from Infineon,
Nuvoton, Atmel, and STMicro but was only able to reproduce this with
LPC and I2C TPMs from Infineon.
The TPM specification only loosely defines this behavior:
TPM Main Level 2 Part 3 v1.2 r116, section 3.3. TPM_SaveState:
The TPM MAY declare all preserved values invalid in response to any
command other than TPM_Init.
TCG PC Client BIOS Spec 1.21 section 8.3.1.
After issuing a TPM_SaveState command, the OS SHOULD NOT issue TPM
commands before transitioning to S3 without issuing another
TPM_SaveState command.
TCG PC Client TIS 1.21, section 4. Power Management:
The TPM_SaveState command allows a Static OS to indicate to the TPM
that the platform may enter a low power state where the TPM will be
required to enter into the D3 power state. The use of the term "may"
is significant in that there is no requirement for the platform to
actually enter the low power state after sending the TPM_SaveState
command. The software may, in fact, send subsequent commands after
sending the TPM_SaveState command.
Change-Id: I52b41e826412688e5b6c8ddd3bb16409939704e9 Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
Peter Huewe [Mon, 4 Mar 2013 14:41:46 +0000 (15:41 +0100)]
tpm: Add support for new Infineon I2C TPM (SLB 9645 TT 1.2 I2C)
This driver adds support for Infineon's new SLB 9645 TT 1.2 I2C TPMs,
which supports clockstretching, combined reads and a bus speed of
up to 400khz. The device also has a new device id.
The driver works now also fine with device trees, so you can
instantiate your device by adding:
+ tpm {
+ compatible = "infineon,slb9645tt";
+ reg = <0x20>;
+ };
for SLB 9645 devices or
char/tpm: Convert struct i2c_msg initialization to C99 format
Convert the struct i2c_msg initialization to C99 format. This makes
maintaining and editing the code simpler. Also helps once other fields
like transferred are added in future.
Thanks to Julia Lawall for automating the conversion.
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com> Acked-by: Peter Huewe <peter.huewe@infineon.com> Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
Jeff Layton [Mon, 1 Apr 2013 12:14:24 +0000 (08:14 -0400)]
selinux: make security_sb_clone_mnt_opts return an error on context mismatch
I had the following problem reported a while back. If you mount the
same filesystem twice using NFSv4 with different contexts, then the
second context= option is ignored. For instance:
# mount server:/export /mnt/test1
# mount server:/export /mnt/test2 -o context=system_u:object_r:tmp_t:s0
# ls -dZ /mnt/test1
drwxrwxrwt. root root system_u:object_r:nfs_t:s0 /mnt/test1
# ls -dZ /mnt/test2
drwxrwxrwt. root root system_u:object_r:nfs_t:s0 /mnt/test2
When we call into SELinux to set the context of a "cloned" superblock,
it will currently just bail out when it notices that we're reusing an
existing superblock. Since the existing superblock is already set up and
presumably in use, we can't go overwriting its context with the one from
the "original" sb. Because of this, the second context= option in this
case cannot take effect.
This patch fixes this by turning security_sb_clone_mnt_opts into an int
return operation. When it finds that the "new" superblock that it has
been handed is already set up, it checks to see whether the contexts on
the old superblock match it. If it does, then it will just return
success, otherwise it'll return -EBUSY and emit a printk to tell the
admin why the second mount failed.
Note that this patch may cause casualties. The NFSv4 code relies on
being able to walk down to an export from the pseudoroot. If you mount
filesystems that are nested within one another with different contexts,
then this patch will make those mounts fail in new and "exciting" ways.
For instance, suppose that /export is a separate filesystem on the
server:
# mount server:/ /mnt/test1
# mount salusa:/export /mnt/test2 -o context=system_u:object_r:tmp_t:s0
mount.nfs: an incorrect mount option was specified
...with the printk in the ring buffer. Because we *might* eventually
walk down to /mnt/test1/export, the mount is denied due to this patch.
The second mount needs the pseudoroot superblock, but that's already
present with the wrong context.
OTOH, if we mount these in the reverse order, then both mounts work,
because the pseudoroot superblock created when mounting /export is
discarded once that mount is done. If we then however try to walk into
that directory, the automount fails for the similar reasons:
# cd /mnt/test1/scratch/
-bash: cd: /mnt/test1/scratch: Device or resource busy
The story I've gotten from the SELinux folks that I've talked to is that
this is desirable behavior. In SELinux-land, mounting the same data
under different contexts is wrong -- there can be only one.
Cc: Steve Dickson <steved@redhat.com> Cc: Stephen Smalley <sds@tycho.nsa.gov> Signed-off-by: Jeff Layton <jlayton@redhat.com> Acked-by: Eric Paris <eparis@redhat.com> Signed-off-by: James Morris <james.l.morris@oracle.com>
Igor Zhbanov [Tue, 19 Mar 2013 09:49:47 +0000 (13:49 +0400)]
Fix NULL pointer dereference in smack_inode_unlink() and smack_inode_rmdir()
This patch fixes kernel Oops because of wrong common_audit_data type
in smack_inode_unlink() and smack_inode_rmdir().
When SMACK security module is enabled and SMACK logging is on (/smack/logging
is not zero) and you try to delete the file which
1) you cannot delete due to SMACK rules and logging of failures is on
or
2) you can delete and logging of success is on,
you will see following:
Unable to handle kernel NULL pointer dereference at virtual address 000002d7
This will set common audit data type to LSM_AUDIT_DATA_DENTRY
and store dentry for auditing (by function smk_curacc(), which in turn calls
dump_common_audit_data(), which is actually uses provided data and logs it).
/*
* You need write access to the thing you're unlinking
*/
rc = smk_curacc(smk_of_inode(ip), MAY_WRITE, &ad);
if (rc == 0) {
/*
* You also need write access to the containing directory
*/
So the dump_common_audit() function incorrectly interprets inode structure
as dentry, and Oops will happen.
This patch reinitializes common_audit_data structures with correct type.
Also I removed unneeded
smk_ad_setfield_u_fs_path_dentry(&ad, NULL);
initialization, because both dentry and inode pointers are stored
in the same union.
Signed-off-by: Igor Zhbanov <i.zhbanov@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Rafal Krypa [Thu, 10 Jan 2013 18:42:00 +0000 (19:42 +0100)]
Smack: add support for modification of existing rules
Rule modifications are enabled via /smack/change-rule. Format is as follows:
"Subject Object rwaxt rwaxt"
First two strings are subject and object labels up to 255 characters.
Third string contains permissions to enable.
Fourth string contains permissions to disable.
All unmentioned permissions will be left unchanged.
If no rule previously existed, it will be created.
Targeted for git://git.gitorious.org/smack-next/kernel.git
Rafal Krypa [Tue, 27 Nov 2012 15:28:11 +0000 (16:28 +0100)]
Smack: prevent revoke-subject from failing when unseen label is written to it
Special file /smack/revoke-subject will silently accept labels that are not
present on the subject label list. Nothing has to be done for such labels,
as there are no rules for them to revoke.
Targeted for git://git.gitorious.org/smack-next/kernel.git
Linus Torvalds [Sun, 10 Mar 2013 00:51:13 +0000 (16:51 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace
Pull namespace bugfixes from Eric Biederman:
"This is three simple fixes against 3.9-rc1. I have tested each of
these fixes and verified they work correctly.
The userns oops in key_change_session_keyring and the BUG_ON triggered
by proc_ns_follow_link were found by Dave Jones.
I am including the enhancement for mount to only trigger requests of
filesystem modules here instead of delaying this for the 3.10 merge
window because it is both trivial and the kind of change that tends to
bit-rot if left untouched for two months."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
proc: Use nd_jump_link in proc_ns_follow_link
fs: Limit sys_mount to only request filesystem modules (Part 2).
fs: Limit sys_mount to only request filesystem modules.
userns: Stop oopsing in key_change_session_keyring
Linus Torvalds [Sat, 9 Mar 2013 18:31:01 +0000 (10:31 -0800)]
Atmel MXT touchscreen: increase reset timeouts
There is a more complete atmel patch-series out by Nick Dyer that fixes
this and other things, but in the meantime this is the minimal thing to
get the touchscreen going on (at least my) Pixel Chromebook.
Not that I want my dirty fingers near that beautiful screen, but it
seems that a non-initialized touchscreen will also end up being a
constant wakeup source, so you have to disable it to go to sleep. And
it's easier to just fix the initialization sequence.
Update proc_ns_follow_link to use nd_jump_link instead of just
manually updating nd.path.dentry.
This fixes the BUG_ON(nd->inode != parent->d_inode) reported by Dave
Jones and reproduced trivially with mkdir /proc/self/ns/uts/a.
Sigh it looks like the VFS change to require use of nd_jump_link
happend while proc_ns_follow_link was baking and since the common case
of proc_ns_follow_link continued to work without problems the need for
making this change was overlooked.
Cc: stable@vger.kernel.org Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Linus Torvalds [Sat, 9 Mar 2013 01:33:20 +0000 (17:33 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"These are scattered fixes and one performance improvement. The
biggest functional change is in how we throttle metadata changes. The
new code bumps our average file creation rate up by ~13% in fs_mark,
and lowers CPU usage.
Stefan bisected out a regression in our allocation code that made
balance loop on extents larger than 256MB."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: improve the delayed inode throttling
Btrfs: fix a mismerge in btrfs_balance()
Btrfs: enforce min_bytes parameter during extent allocation
Btrfs: allow running defrag in parallel to administrative tasks
Btrfs: avoid deadlock on transaction waiting list
Btrfs: do not BUG_ON on aborted situation
Btrfs: do not BUG_ON in prepare_to_reloc
Btrfs: free all recorded tree blocks on error
Btrfs: build up error handling for merge_reloc_roots
Btrfs: check for NULL pointer in updating reloc roots
Btrfs: fix unclosed transaction handler when the async transaction commitment fails
Btrfs: fix wrong handle at error path of create_snapshot() when the commit fails
Btrfs: use set_nlink if our i_nlink is 0
Benson Leung [Fri, 8 Mar 2013 03:43:34 +0000 (19:43 -0800)]
Platform: x86: chromeos_laptop : Add basic platform data for atmel devices
Add basic platform data to get the current upstream driver working
with the 224s touchpad and 1664s touchscreen.
We will be using NULL config so we will use the settings from the
devices' NVRAMs.
Daniel Kurtz [Fri, 8 Mar 2013 03:43:33 +0000 (19:43 -0800)]
Input: atmel_mxt_ts - Support for touchpad variant
This same driver can be used by atmel based touchscreens and touchpads
(buttonpads). Platform data may specify a device is a touchpad
using the is_tp flag.
This will cause the driver to perform some touchpad specific
initializations, such as:
* register input device name "Atmel maXTouch Touchpad" instead of
Touchscreen.
* register BTN_LEFT & BTN_TOOL_* event types.
* register axis resolution (as a fixed constant, for now)
* register BUTTONPAD property
* process GPIO buttons using reportid T19
Input event GPIO mapping is done by the platform data key_map array.
key_map[x] should contain the KEY or BTN code to send when processing
GPIOx from T19. To specify a GPIO as not an input source, populate
with KEY_RESERVED, or 0.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org> Signed-off-by: Benson Leung <bleung@chromium.org> Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk> Tested-by: Olof Johansson <olof@lixom.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 8 Mar 2013 23:22:08 +0000 (15:22 -0800)]
Merge branch 'for-next' of git://git.samba.org/sfrench/cifs-2.6
Pull CIFS fixes from Steve French:
"A small set of cifs fixes which includes one for a recent regression
in the write path (pointed out by Anton), some fixes for rename
problems and as promised for 3.9 removing the obsolete sockopt mount
option (and the accompanying deprecation warning)."
* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
CIFS: Fix missing of oplock_read value in smb30_values structure
cifs: don't try to unlock pagecache page after releasing it
cifs: remove the sockopt= mount option
cifs: Check server capability before attempting silly rename
cifs: Fix bug when checking error condition in cifs_rename_pending_delete()
Linus Torvalds [Fri, 8 Mar 2013 23:05:42 +0000 (15:05 -0800)]
Merge branch 'akpm' (fixes from Andrew)
Merge misc fixes from Andrew Morton.
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
alpha: boot: fix build breakage introduced by system.h disintegration
memcg: initialize kmem-cache destroying work earlier
Randy has moved
ksm: fix m68k build: only NUMA needs pfn_to_nid
dmi_scan: fix missing check for _DMI_ signature in smbios_present()
Revert parts of "hlist: drop the node parameter from iterators"
idr: remove WARN_ON_ONCE() on negative IDs
mm/mempolicy.c: fix sp_node_init() argument ordering
mm/mempolicy.c: fix wrong sp_node insertion
ipc: don't allocate a copy larger than max
ipc: fix potential oops when src msg > 4k w/ MSG_COPY
Will Deacon [Fri, 8 Mar 2013 20:43:37 +0000 (12:43 -0800)]
alpha: boot: fix build breakage introduced by system.h disintegration
Commit ec2212088c42 ("Disintegrate asm/system.h for Alpha") removed the
system.h include from boot/head.S, which puts the PAL_* asm constants
out of scope.
Include <asm/pal.h> so we can get building again.
Signed-off-by: Will Deacon <will.deacon@arm.com> Cc: David Rusling <david.rusling@linaro.org> Cc: David Howells <dhowells@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
memcg: initialize kmem-cache destroying work earlier
Fix a warning from lockdep caused by calling cancel_work_sync() for
uninitialized struct work. This path has been triggered by destructon
kmem-cache hierarchy via destroying its root kmem-cache.
cache ffff88003c072d80
obj ffff88003b410000 cache ffff88003c072d80
obj ffff88003b924000 cache ffff88003c20bd40
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
Pid: 2825, comm: insmod Tainted: G O 3.9.0-rc1-next-20130307+ #611
Call Trace:
__lock_acquire+0x16a2/0x1cb0
lock_acquire+0x8a/0x120
flush_work+0x38/0x2a0
__cancel_work_timer+0x89/0xf0
cancel_work_sync+0xb/0x10
kmem_cache_destroy_memcg_children+0x81/0xb0
kmem_cache_destroy+0xf/0xe0
init_module+0xcb/0x1000 [kmem_test]
do_one_initcall+0x11a/0x170
load_module+0x19b0/0x2320
SyS_init_module+0xc6/0xf0
system_call_fastpath+0x16/0x1b
Hugh Dickins [Fri, 8 Mar 2013 20:43:34 +0000 (12:43 -0800)]
ksm: fix m68k build: only NUMA needs pfn_to_nid
A CONFIG_DISCONTIGMEM=y m68k config gave
mm/ksm.c: In function `get_kpfn_nid':
mm/ksm.c:492: error: implicit declaration of function `pfn_to_nid'
linux/mmzone.h declares it for CONFIG_SPARSEMEM and CONFIG_FLATMEM, but
expects the arch's asm/mmzone.h to declare it for CONFIG_DISCONTIGMEM
(see arch/mips/include/asm/mmzone.h for example).
Or perhaps it is only expected when CONFIG_NUMA=y: too much of a maze,
and m68k got away without it so far, so fix the build in mm/ksm.c.
Signed-off-by: Hugh Dickins <hughd@google.com> Reported-by: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Petr Holasek <pholasek@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ben Hutchings [Fri, 8 Mar 2013 20:43:32 +0000 (12:43 -0800)]
dmi_scan: fix missing check for _DMI_ signature in smbios_present()
Commit 9f9c9cbb6057 ("drivers/firmware/dmi_scan.c: fetch dmi version
from SMBIOS if it exists") hoisted the check for "_DMI_" into
dmi_scan_machine(), which means that we don't bother to check for
"_DMI_" at offset 16 in an SMBIOS entry. smbios_present() may also call
dmi_present() for an address where we found "_SM_", if it failed further
validation.
Check for "_DMI_" in smbios_present() before calling dmi_present().
[akpm@linux-foundation.org: fix build] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Reported-by: Tim McGrath <tmhikaru@gmail.com> Tested-by: Tim Mcgrath <tmhikaru@gmail.com> Cc: Zhenzhong Duan <zhenzhong.duan@oracle.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Arnd Bergmann [Fri, 8 Mar 2013 20:43:31 +0000 (12:43 -0800)]
Revert parts of "hlist: drop the node parameter from iterators"
Commit b67bfe0d42ca ("hlist: drop the node parameter from iterators")
did a lot of nice changes but also contains two small hunks that seem to
have slipped in accidentally and have no apparent connection to the
intent of the patch.
This reverts the two extraneous changes.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Cc: Peter Senna Tschudin <peter.senna@gmail.com> Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: Sasha Levin <sasha.levin@oracle.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Tejun Heo [Fri, 8 Mar 2013 20:43:30 +0000 (12:43 -0800)]
idr: remove WARN_ON_ONCE() on negative IDs
idr_find(), idr_remove() and idr_replace() used to silently ignore the
sign bit and perform lookup with the rest of the bits. The weird behavior
has been changed such that negative IDs are treated as invalid. As the
behavior change was subtle, WARN_ON_ONCE() was added in the hope of
determining who's calling idr functions with negative IDs so that they can
be examined for problems.
Up until now, all two reported cases are ID number coming directly from
userland and getting fed into idr_find() and the warnings seem to cause
more problems than being helpful. Drop the WARN_ON_ONCE()s.
Peter Hurley [Fri, 8 Mar 2013 20:43:27 +0000 (12:43 -0800)]
ipc: don't allocate a copy larger than max
When MSG_COPY is set, a duplicate message must be allocated for the copy
before locking the queue. However, the copy could not be larger than was
sent which is limited to msg_ctlmax.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Acked-by: Stanislav Kinsbursky <skinsbursky@parallels.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 8 Mar 2013 22:46:04 +0000 (14:46 -0800)]
Merge branch 'stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile
Pull tile architecture fixes from Chris Metcalf:
"This fixes the bug that Al Viro spotted with the compat llseek code.
I also fixed the compat syscall definitions to use the new syscall
define macros to properly sign-extend their arguments."
* 'stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
tile: properly use COMPAT_SYSCALL_DEFINEx
tile: work around bug in the generic sys_llseek
Linus Torvalds [Fri, 8 Mar 2013 22:45:17 +0000 (14:45 -0800)]
Merge tag 'metag-for-v3.9-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/metag
Pull metag bugfixes from James Hogan:
"A couple of fairly minor arch/metag integration fixes from v3.9-rc1:
- remove SET_PERSONALITY(): use default definition like other arches
now do.
- inhibit NUMA balancing: like SH, NUMA is used for memories with
different latencies. ARCH_WANT_VARIABLE_LOCALITY has been added
for this purpose."
* tag 'metag-for-v3.9-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/metag:
metag: Inhibit NUMA balancing.
metag: remove SET_PERSONALITY()
Linus Torvalds [Fri, 8 Mar 2013 22:43:33 +0000 (14:43 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"All are boring small fixes in various parts:
- A few possible NULL-dereference or zero-division Oops fixes
- Fix vmaster slave volume notification
- Add codec ID for ALC233
- Various fixes in several ASoC WM codecs
- ASoC tegra i2c fix
Sorry if you wanted a thrilling adventure with huge sharks :)"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: ice1712: Initialize card->private_data properly
ALSA: hda - Add support of new codec ALC233
ALSA: hda/ca0132 - Avoid division by zero in dspxfr_one_seg()
ALSA: hda - check NULL pointer when creating SPDIF PCM switch
ALSA: hda - check NULL pointer when creating SPDIF controls
ASoC: wm5102: Apply a SYSCLK patch for later revs
ALSA: vmaster: Fix slave change notification
ASoC: tegra: fix I2S bit count mask
ALSA: seq: seq_oss_event: missing range checks
ASoC: wm8350: Use jiffies rather than msecs in schedule_delayed_work()
ASoC: wm5110: Correct OUT2/3 volume and switch names
ASoC: wm5102: Correct OUT2 volume and switch names
ASoC: wm8960: Fix ADC power bits
ASoC: wm8960: Correct register 0 and 1 defaults
Linus Torvalds [Fri, 8 Mar 2013 22:42:52 +0000 (14:42 -0800)]
Merge branch 'for-3.9/upstream-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
Pull HID fix from Jiri Kosina:
"Bugfix for a long-standing bug in logitech-dj driver causing all sorts
of random initialization problems, finally debugged by Benjamin
Tissoires with help of Bob Bowles."
* 'for-3.9/upstream-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: logitech-dj: do not directly call hid_output_raw_report() during probe
Linus Torvalds [Fri, 8 Mar 2013 17:03:07 +0000 (09:03 -0800)]
vfs: don't BUG_ON() if following a /proc fd pseudo-symlink results in a symlink
It's "normal" - it can happen if the file descriptor you followed was
opened with O_NOFOLLOW.
Reported-by: Dave Jones <davej@redhat.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: stable@kernel.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Thu, 7 Mar 2013 23:57:38 +0000 (15:57 -0800)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Peter Anvin:
"Several boot fixes (MacBook, legacy EFI bootloaders), another
please-don't-brick fix, and some minor stuff."
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: Do not try to sync identity map for non-mapped pages
x86, doc: Be explicit about what the x86 struct boot_params requires
x86: Don't clear efi_info even if the sentinel hits
x86, mm: Make sure to find a 2M free block for the first mapped area
x86: Fix 32-bit *_cpu_data initializers
efivarfs: return accurate error code in efivarfs_fill_super()
efivars: efivarfs_valid_name() should handle pstore syntax
efi: be more paranoid about available space when creating variables
iommu, x86: Add DMA remap fault reason
x86, smpboot: Remove unused variable
Linus Torvalds [Thu, 7 Mar 2013 22:55:54 +0000 (14:55 -0800)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Misc radeon, nouveau, mgag200 and intel fixes.
The intel fixes should contain the fix for the touchpad on the
Chromebook - hey I'm an input maintainer now!"
Hate to pee on your parade, Dave, but I don't think being an input
maintainer is necessarily something to strive for..
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (25 commits)
drm/tegra: drop "select DRM_HDMI"
drm: Documentation typo fixes
drm/mgag200: Bug fix: Renesas board now selects native resolution.
drm/mgag200: Reject modes that are too big for VRAM
drm/mgag200: 'fbdev_list' in 'struct mga_fbdev' is not used
drm/radeon: don't check mipmap alignment if MIP_ADDRESS is FMASK
drm/radeon: skip MC reset as it's probably not hung
drm/radeon: add primary dac adj quirk for R200 board
drm/radeon: don't set hpd, afmt interrupts when interrupts are disabled
drm/i915: Turn off hsync and vsync on ADPA when disabling crt
drm/i915: Fix incorrect definition of ADPA HSYNC and VSYNC bits
drm/i915: also disable south interrupts when handling them
drm/i915: enable irqs earlier when resuming
drm/i915: Increase the RC6p threshold.
DRM/i915: On G45 enable cursor plane briefly after enabling the display plane.
drm/nv50-: prevent some races between modesetting and page flipping
drm/nouveau/i2c: drop parent refcount when creating ports
drm/nv84: fix regression in page flipping
drm/nouveau: Fix typo in init_idx_addr_latched().
drm/nouveau: Disable AGP on PowerPC again.
...
Linus Torvalds [Thu, 7 Mar 2013 22:54:28 +0000 (14:54 -0800)]
Merge tag 'pm+acpi-3.9-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael J Wysocki:
- Two fixes for the new intel_pstate driver from Dirk Brandewie.
- Fix for incorrect usage of the .find_bridge() callback from struct
acpi_bus_type in the USB core and subsequent removal of that callback
from Rafael J Wysocki.
- ACPI processor driver cleanups from Chen Gang and Syam Sidhardhan.
- ACPI initialization and error messages fix from Joe Perches.
- Operating Performance Points documentation improvement from Nishanth
Menon.
- Fixes for memory leaks and potential concurrency issues and sysfs
attributes leaks during device removal in the core device PM QoS code
from Rafael J Wysocki.
- Calxeda Highbank cpufreq driver simplification from Emilio López.
- cpufreq comment cleanup from Namhyung Kim.
- Fix for a section mismatch in Calxeda Highbank interprocessor
communication code from Mark Langsdorf (this is not a PM fix strictly
speaking, but the code in question went in through the PM tree).
* tag 'pm+acpi-3.9-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq / intel_pstate: Do not load on VM that does not report max P state.
cpufreq / intel_pstate: Fix intel_pstate_init() error path
ACPI / glue: Drop .find_bridge() callback from struct acpi_bus_type
ACPI / glue: Add .match() callback to struct acpi_bus_type
ACPI / porocessor: Beautify code, pr->id is u32 which is never < 0
ACPI / processor: Remove redundant NULL check before kfree
ACPI / Sleep: Avoid interleaved message on errors
PM / QoS: Remove device PM QoS sysfs attributes at the right place
PM / QoS: Fix concurrency issues and memory leaks in device PM QoS
cpufreq: highbank: do not initialize array with a loop
PM / OPP: improve introductory documentation
cpufreq: Fix a typo in comment
mailbox, pl320-ipc: remove __init from probe function
Paul Bolle [Tue, 5 Mar 2013 21:07:36 +0000 (22:07 +0100)]
drm/tegra: drop "select DRM_HDMI"
Commit ac24c2204a76e5b42aa103bf963ae0eda1b827f3 ("drm/tegra: Use generic
HDMI infoframe helpers") added "select DRM_HDMI" to the DRM_TEGRA
Kconfig entry. But there is no Kconfig symbol named DRM_HDMI. The select
statement for that symbol is a nop. Drop it.
What was needed to use HDMI functionality was to select HDMI (which this
entry already did through depending on DRM) and to include linux/hdmi.h
(which this commit also did).
Signed-off-by: Paul Bolle <pebolle@tiscali.nl> Acked-by: Thierry Reding <thierry.reding@avionic-design.de> Signed-off-by: Dave Airlie <airlied@redhat.com>
Julia Lemire [Thu, 7 Mar 2013 15:41:03 +0000 (10:41 -0500)]
drm/mgag200: Bug fix: Renesas board now selects native resolution.
Renesas boards were consistently defaulting to the 1024x768 resolution,
regardless of the native resolution of the monitor plugged in. It was
determined that the EDID of the monitor was not being read. Since the
DAC is a shared line, in order to read from or write to it we must take
control of the DAC clock. This can be done by setting the proper
register to one.
This bug fix sets the register MGA1064_GEN_IO_CTL2 to one. The DAC
control line can be used to determine whether or not a new monitor has
been plugged in. But since the hotplug feature is not one we will
support, it has been decided to simply leave the register set to one.
Signed-off-by: Julia Lemire <jlemire@matrox.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
drm/mgag200: Reject modes that are too big for VRAM
A monitor or a user could request a resolution greater than the
available VRAM for the backing framebuffer. This change checks the
required framebuffer size against the max VRAM size and rejects modes
if they are too big. This change can also remove a mode request passed
in via the video= parameter.
Signed-off-by: Christopher Harvey <charvey@matrox.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie [Thu, 7 Mar 2013 22:28:22 +0000 (08:28 +1000)]
Merge branch 'drm-fixes-3.9' of git://people.freedesktop.org/~agd5f/linux into drm-next
Alex writes:
Radeon fixes pull. Not much to it.
- fix some splatter if the interrupt handler isn't registered
- Add a quirk for an old R200 board to fix washed out colors on the DAC
- Don't try and soft reset the MC when we reset the GPU. It usually doesn't
need it and doesn't always work reliably.
- A CS checker fix from Marek
* 'drm-fixes-3.9' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: don't check mipmap alignment if MIP_ADDRESS is FMASK
drm/radeon: skip MC reset as it's probably not hung
drm/radeon: add primary dac adj quirk for R200 board
drm/radeon: don't set hpd, afmt interrupts when interrupts are disabled
Linus Torvalds [Thu, 7 Mar 2013 21:47:18 +0000 (13:47 -0800)]
Merge branch 'fixes' of git://git.linaro.org/people/rmk/linux-arm
Pull ARM fixes from Russell King:
"Mainly a group of fixes, the only exception is the wiring up of the
kcmp syscall now that those patches went in during the last merge
window."
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7668/1: fix memset-related crashes caused by recent GCC (4.7.2) optimizations
ARM: 7667/1: perf: Fix section mismatch on armpmu_init()
ARM: 7666/1: decompressor: add -mno-single-pic-base for building the decompressor
ARM: 7665/1: Wire up kcmp syscall
ARM: 7664/1: perf: remove erroneous semicolon from event initialisation
ARM: 7663/1: perf: fix ARMv7 EVTYPE_MASK to include NSH bit
ARM: 7662/1: hw_breakpoint: reset debug logic on secondary CPUs in s2ram resume
ARM: 7661/1: mm: perform explicit branch predictor maintenance when required
ARM: 7660/1: tlb: add branch predictor maintenance operations
ARM: 7659/1: mm: make mm->context.id an atomic64_t variable
ARM: 7658/1: mm: fix race updating mm->context.id on ASID rollover
ARM: 7657/1: head: fix swapper and idmap population with LPAE and big-endian
ARM: 7655/1: smp_twd: make twd_local_timer_of_register() no-op for nosmp
ARM: 7652/1: mm: fix missing use of 'asid' to get asid value from mm->context.id
ARM: 7642/1: netx: bump IRQ offset to 64
H. Peter Anvin [Thu, 7 Mar 2013 21:25:10 +0000 (13:25 -0800)]
Merge tag 'efi-for-3.9-rc2' into x86/urgent
EFI changes for v3.9-rc2,
* Make the EFI variable code more paranoid about running out of
space in NVRAM, since this is the root cause of the recent issue
where machines refuse to boot - from Matthew Garrett.
* Some efivarfs patches that fix regressions introduced in v3.9-rc1.
Dave Hansen [Thu, 7 Mar 2013 16:31:51 +0000 (08:31 -0800)]
x86: Do not try to sync identity map for non-mapped pages
kernel_map_sync_memtype() is called from a variety of contexts. The
pat.c code that calls it seems to ensure that it is not called for
non-ram areas by checking via pat_pagerange_is_ram(). It is important
that it only be called on the actual identity map because there *IS*
no map to sync for highmem pages, or for memory holes.
The ioremap.c uses are not as careful as those from pat.c, and call
kernel_map_sync_memtype() on PCI space which is in the middle of the
kernel identity map _range_, but is not actually mapped.
This patch adds a check to kernel_map_sync_memtype() which probably
duplicates some of the checks already in pat.c. But, it is necessary
for the ioremap.c uses and shouldn't hurt other callers.
I have reproduced this bug and this patch fixes it for me and the
original bug reporter:
Linus Torvalds [Thu, 7 Mar 2013 21:07:10 +0000 (13:07 -0800)]
Merge tag 'regulator-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"A few small things here and there, nothing major here really. The
conversion of twl4030ldo_ops to get_voltage_sel is a fix, as covered
in the commit log it fixes inconsistency in handling of the IS_UNSUP()
feature in the driver."
* tag 'regulator-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: fixed regulator_bulk_enable unwinding code
regulator: twl: Convert twl4030ldo_ops to get_voltage_sel
regulator: palmas: fix number of SMPS voltages
regulator: core: fix documentation error in regulator_allow_bypass
regulator: core: update kernel documentation for regulator_desc
regulator: db8500-prcmu - remove incorrect __exit markup
Linus Torvalds [Thu, 7 Mar 2013 21:06:21 +0000 (13:06 -0800)]
Merge tag 'regmap-v3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap PM fix from Mark Brown:
"A simple fix to stop us leaking a runtime PM reference in the case
where we fail to enable a device."
* tag 'regmap-v3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: irq: call pm_runtime_put in pm_runtime_get_sync failed case
Linus Torvalds [Thu, 7 Mar 2013 20:47:24 +0000 (12:47 -0800)]
Merge tag 'ecryptfs-3.9-rc2-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs
Pull ecryptfs fixes from Tyler Hicks:
"Minor code cleanups and new Kconfig option to disable /dev/ecryptfs
The code cleanups fix up W=1 compiler warnings and some unnecessary
checks. The new Kconfig option, defaulting to N, allows the rarely
used eCryptfs kernel to userspace communication channel to be compiled
out. This may be the first step in it being eventually removed."
Hmm. I'm not sure whether these should be called "fixes", and it
probably should have gone in the merge window. But I'll let it slide.
* tag 'ecryptfs-3.9-rc2-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs:
eCryptfs: allow userspace messaging to be disabled
eCryptfs: Fix redundant error check on ecryptfs_find_daemon_by_euid()
ecryptfs: ecryptfs_msg_ctx_alloc_to_free(): remove kfree() redundant null check
eCryptfs: decrypt_pki_encrypted_session_key(): remove kfree() redundant null check
eCryptfs: remove unneeded checks in virt_to_scatterlist()
eCryptfs: Fix -Wmissing-prototypes warnings
eCryptfs: Fix -Wunused-but-set-variable warnings
eCryptfs: initialize payload_len in keystore.c
Linus Torvalds [Thu, 7 Mar 2013 20:46:25 +0000 (12:46 -0800)]
Merge tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon patches from Guenter Roeck:
"Bug fixes for sht15 and ltc2978 driver plus some documentation
updates"
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (sht15) Check return value of regulator_enable()
hwmon: (adt7410) Document ADT7420 support
hwmon: (pmbus/ltc2978) Use detected chip ID to select supported functionality
hwmon: (pmbus/ltc2978) Fix peak attribute handling
hwmon: (pmbus/ltc2978) Update datasheet links
hwmon: Update my e-mail address in driver documentation
Marek Olšák [Fri, 1 Mar 2013 12:40:31 +0000 (13:40 +0100)]
drm/radeon: don't check mipmap alignment if MIP_ADDRESS is FMASK
The MIP_ADDRESS state has 2 meanings. If the texture has one sample
per pixel, it's a pointer to the mipmap chain. If the texture has
multiple samples per pixel, it's a pointer to FMASK, a metadata buffer
needed for reading compressed MSAA textures. The mipmap
alignment rules do not apply to FMASK.
Signed-off-by: Marek Olšák <maraeo@gmail.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Alex Deucher [Thu, 28 Feb 2013 15:03:08 +0000 (10:03 -0500)]
drm/radeon: skip MC reset as it's probably not hung
The MC is mostly likely busy (e.g., display requests), not hung
so no need to reset it. Doing an MC reset is tricky and not
particularly reliable. Fixes hangs in certain cases.
Reported-by: Josh Boyer <jwboyer@gmail.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Recent GCC versions (e.g. GCC-4.7.2) perform optimizations based on
assumptions about the implementation of memset and similar functions.
The current ARM optimized memset code does not return the value of
its first argument, as is usually expected from standard implementations.
GCC assumes memset returns the value of pointer 'waiter' in register r0; causing
register/memory corruptions.
This patch fixes the return value of the assembly version of memset.
It adds a 'mov' instruction and merges an additional load+store into
existing load/store instructions.
For ease of review, here is a breakdown of the patch into 4 simple steps:
Step 1
======
Perform the following substitutions:
ip -> r8, then
r0 -> ip,
and insert 'mov ip, r0' as the first statement of the function.
At this point, we have a memset() implementation returning the proper result,
but corrupting r8 on some paths (the ones that were using ip).
Step 2
======
Make sure r8 is saved and restored when (! CALGN(1)+0) == 1:
Step 4
======
Rewrite register list "r4-r7, r8" as "r4-r8".
Signed-off-by: Ivan Djelic <ivan.djelic@parrot.com> Reviewed-by: Nicolas Pitre <nico@linaro.org> Signed-off-by: Dirk Behme <dirk.behme@gmail.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
HID: logitech-dj: do not directly call hid_output_raw_report() during probe
hid_output_raw_report() makes a direct call to usb_control_msg(). However,
some USB3 boards have shown that the usb device is not ready during the
.probe(). This blocks the entire usb device, and the paired mice, keyboards
are not functional. The dmesg output is the following:
[ 11.912287] logitech-djreceiver 0003:046D:C52B.0003: hiddev0,hidraw0: USB HID v1.11 Device [Logitech USB Receiver] on usb-0000:00:14.0-2/input2
[ 11.912537] logitech-djreceiver 0003:046D:C52B.0003: logi_dj_probe:logi_dj_recv_query_paired_devices error:-32
[ 11.912636] logitech-djreceiver: probe of 0003:046D:C52B.0003 failed with error -32
Relying on the scheduled call to usbhid_submit_report() fixes the problem.
related bugs:
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1072082
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1039143
https://bugzilla.redhat.com/show_bug.cgi?id=840391
https://bugzilla.kernel.org/show_bug.cgi?id=49781
Reported-and-tested-by: Bob Bowles <bobjohnbowles@gmail.com> Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Chris Mason [Mon, 4 Mar 2013 22:13:31 +0000 (17:13 -0500)]
Btrfs: improve the delayed inode throttling
The delayed inode code batches up changes to the btree in hopes of doing
them in bulk. As the changes build up, processes kick off worker
threads and wait for them to make progress.
The current code kicks off an async work queue item for each delayed
node, which creates a lot of churn. It also uses a fixed 1 HZ waiting
period for the throttle, which allows us to build a lot of pending
work and can slow down the commit.
This changes us to watch a sequence counter as it is bumped during the
operations. We kick off fewer work items and have each work item do
more work.
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
Josh Boyer [Thu, 7 Mar 2013 04:23:30 +0000 (20:23 -0800)]
x86: Don't clear efi_info even if the sentinel hits
When boot_params->sentinel is set, all we really know is that some
undefined set of fields in struct boot_params contain garbage. In the
particular case of efi_info, however, there is a private magic for
that substructure, so it is generally safe to leave it even if the
bootloader is broken.
kexec (for which we did the initial analysis) did not initialize this
field, but of course all the EFI bootloaders do, and most EFI
bootloaders are broken in this respect (and should be fixed.)
It turns out that we do not calculate the real_end properly:
We try to get 2M size with 4K alignment, and later will round down
to 2M, so we will get less then 2M for first mapping, in extreme
case could be only 4K only. In Henrik's system it has (1M-32K) as
last usable rage is [mem 0x7f9db000-0x7fef8fff].
The problem is exposed when EFI booting have several holes and it
will force mapping to use PTE instead as we only map usable areas.
To fix it, just make it be 2M aligned, so we can be guaranteed to be
able to use large pages to map it.
Krzysztof Mazur [Sat, 2 Mar 2013 23:14:42 +0000 (00:14 +0100)]
x86: Fix 32-bit *_cpu_data initializers
The commit 27be457000211a6903968dfce06d5f73f051a217
('x86 idle: remove 32-bit-only "no-hlt" parameter, hlt_works_ok
flag') removed the hlt_works_ok flag from struct cpuinfo_x86, but
boot_cpu_data and new_cpu_data initializers were not changed
causing setting f00f_bug flag, instead of fdiv_bug.
If CONFIG_X86_F00F_BUG is not set the f00f_bug flag is never
cleared.
To avoid such problems in future C99-style initialization is now
used.
Ilya Dryomov [Wed, 6 Mar 2013 08:57:55 +0000 (01:57 -0700)]
Btrfs: fix a mismerge in btrfs_balance()
Raid56 merge (merge commit e942f88) had mistakenly removed a call to
__cancel_balance(), which resulted in balance not cleaning up after itself
after a successful finish. (Cleanup includes switching the state, removing
the balance item and releasing mut_ex_op testnset lock.) Bring it back.
Reported-by: David Sterba <dsterba@suse.cz> Signed-off-by: Ilya Dryomov <idryomov@gmail.com> Signed-off-by: Chris Mason <chris.mason@fusionio.com>
Dave Airlie [Thu, 7 Mar 2013 01:12:14 +0000 (11:12 +1000)]
Merge branch 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel into drm-next
A bunch of fixes, nothing truely horrible:
- Fix PCH irq handling race which resulted in missed gmbus/dp aux irqs
and subsequent fallout (Paulo)
- Fixup off-by-one in our hsw id table (Kenneth)
- Fixup ilk rc6 support (disabled by default), regression introduced in
3.8
- g4x plane w/a from Egbert Eich
- gen2/3/4 dpms suspend/standy fixes for VGA outputs from Patrik Jakobsson
- Workaround dying ivb machines with less aggressive rc6 values (Stéphane
Marchesin)
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: Turn off hsync and vsync on ADPA when disabling crt
drm/i915: Fix incorrect definition of ADPA HSYNC and VSYNC bits
drm/i915: also disable south interrupts when handling them
drm/i915: enable irqs earlier when resuming
drm/i915: Increase the RC6p threshold.
DRM/i915: On G45 enable cursor plane briefly after enabling the display plane.
drm/i915: Fix Haswell/CRW PCI IDs.
drm/i915: Don't clobber crtc->fb when queue_flip fails
drm/i915: wait_event_timeout's timeout is in jiffies
drm/i915: Fix missing variable initilization
Jeff Layton [Mon, 4 Mar 2013 20:18:25 +0000 (15:18 -0500)]
cifs: don't try to unlock pagecache page after releasing it
We had a recent fix to fix the release of pagecache pages when
cifs_writev_requeue writes fail. Unfortunately, it releases the page
before trying to unlock it. At that point, the page might be gone by the
time the unlock comes in.
Unlock the page first before checking the value of "rc", and only then
end writeback and release the pages. The page lock isn't required for
any of those operations so this should be safe.
Reported-by: Anton Altaparmakov <aia21@cam.ac.uk> Signed-off-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Steve French <sfrench@us.ibm.com>
Sachin Prabhu [Tue, 5 Mar 2013 19:25:56 +0000 (19:25 +0000)]
cifs: Check server capability before attempting silly rename
cifs_rename_pending_delete() attempts to silly rename file using
CIFSSMBRenameOpenFile(). This uses the SET_FILE_INFORMATION TRANS2
command with information level set to the passthru info-level
SMB_SET_FILE_RENAME_INFORMATION.
We need to check to make sure that the server support passthru
info-levels before attempting the silly rename or else we will fail to
rename the file.
Signed-off-by: Sachin Prabhu <sprabhu@redhat.com> Reviewed-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Steve French <sfrench@us.ibm.com>
Sachin Prabhu [Tue, 5 Mar 2013 19:25:55 +0000 (19:25 +0000)]
cifs: Fix bug when checking error condition in cifs_rename_pending_delete()
Fix check for error condition after setting attributes with
CIFSSMBSetFileInfo().
Signed-off-by: Sachin Prabhu <sprabhu@redhat.com> Reviewed-by: Jeff Layton <jlayton@redhat.com> Reviewed-by: Pavel Shilovsky <piastry@etersoft.ru> Signed-off-by: Steve French <sfrench@us.ibm.com>
Stephen Boyd [Tue, 5 Mar 2013 02:54:06 +0000 (03:54 +0100)]
ARM: 7667/1: perf: Fix section mismatch on armpmu_init()
WARNING: vmlinux.o(.text+0xfb80): Section mismatch in reference
from the function armpmu_register() to the function
.init.text:armpmu_init()
The function armpmu_register() references
the function __init armpmu_init().
This is often because armpmu_register lacks a __init
annotation or the annotation of armpmu_init is wrong.
Just drop the __init marking on armpmu_init() because
armpmu_register() no longer has an __init marking.
Acked-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Jonathan Austin [Mon, 4 Mar 2013 14:17:36 +0000 (15:17 +0100)]
ARM: 7666/1: decompressor: add -mno-single-pic-base for building the decompressor
Before jumping to (position independent) C-code from the decompressor's
assembler world we set-up the C environment. This setup currently does not
set r9, which for arm-none-uclinux-uclibceabi toolchains is by default
expected to be the PIC offset base register (IE should point to the
beginning of the GOT).
Currently, therefore, in order to build working kernels that use the
decompressor it is necessary to use an arm-linux-gnueabi toolchain, or
similar. uClinux toolchains cause a prefetch abort to occur at the beginning
of the decompress_kernel function.
This patch allows uClinux toolchains to build bootable zImages by forcing
the -mno-single-pic-base option, which ensures that the location of the GOT
is re-derived each time it is required, and r9 becomes free for use as a
general purpose register.
This has a small (4% in instruction terms) advantage over the alternative of
setting r9 to point to the GOT before calling into the C-world.
Signed-off-by: Jonathan Austin <jonathan.austin@arm.com> Acked-by: Nicolas Pitre <nico@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* pm-fixes:
cpufreq / intel_pstate: Do not load on VM that does not report max P state.
cpufreq / intel_pstate: Fix intel_pstate_init() error path
PM / QoS: Remove device PM QoS sysfs attributes at the right place
PM / QoS: Fix concurrency issues and memory leaks in device PM QoS
cpufreq: highbank: do not initialize array with a loop
PM / OPP: improve introductory documentation
cpufreq: Fix a typo in comment
mailbox, pl320-ipc: remove __init from probe function
If cpufreq_register_driver() fails just free memory that has been
allocated and return. intel_pstate_exit() function is removed since we
are built-in only now there is no reason for a module exit procedure.
Reported-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
projects / linux-beck.git / log