The PM hooks are no-op if the r8169 interface is down (i.e. !IFF_UP).
However, as the chipset is enabled, the device will not work after a
suspend/resume cycle. The patch always issue the required PCI suspend
sequence and removes the module unload/reload workaround.
Jean Delvare [Tue, 10 Apr 2007 21:06:06 +0000 (23:06 +0200)]
APPLETALK: Fix a remotely triggerable crash (CVE-2007-1357)
When we receive an AppleTalk frame shorter than what its header says,
we still attempt to verify its checksum, and trip on the BUG_ON() at
the end of function atalk_sum_skb() because of the length mismatch.
This has security implications because this can be triggered by simply
sending a specially crafted ethernet frame to a target victim,
effectively crashing that host. Thus this qualifies, I think, as a
remote DoS. Here is the frame I used to trigger the crash, in npg
format:
<Appletalk Killer>
{
# Ethernet header -----
XX XX XX XX XX XX # Destination MAC
00 00 00 00 00 00 # Source MAC
00 1D # Length
The destination MAC address must be set to those of the victim.
The severity is mitigated by two requirements:
* The target host must have the appletalk kernel module loaded. I
suspect this isn't so frequent.
* AppleTalk frames are non-IP, thus I guess they can only travel on
local networks. I am no network expert though, maybe it is possible
to somehow encapsulate AppleTalk packets over IP.
The bug has been reported back in June 2004:
http://bugzilla.kernel.org/show_bug.cgi?id=2979
But it wasn't investigated, and was closed in July 2006 as both
reporters had vanished meanwhile.
This code was new in kernel 2.6.0-test5:
http://git.kernel.org/?p=linux/kernel/git/tglx/history.git;a=commitdiff;h=7ab442d7e0a76402c12553ee256f756097cae2d2
And not modified since then, so we can assume that vanilla kernels
2.6.0-test5 and later, and distribution kernels based thereon, are
affected.
Note that I still do not know for sure what triggered the bug in the
real-world cases. The frame could have been corrupted by the kernel if
we have a bug hiding somewhere. But more likely, we are receiving the
faulty frame from the network.
Signed-off-by: Jean Delvare <jdelvare@suse.de> Signed-off-by: Adrian Bunk <bunk@stusta.de>
Thomas Gleixner [Sun, 8 Apr 2007 23:04:23 +0000 (01:04 +0200)]
hrtimer: prevent overrun DoS in hrtimer_forward()
hrtimer_forward() does not check for the possible overflow of
timer->expires. This can happen on 64 bit machines with large interval
values and results currently in an endless loop in the softirq because
the expiry value becomes negative and therefor the timer is expired all
the time.
Check for this condition and set the expiry value to the max. expiry
time in the future.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Adrian Bunk <bunk@stusta.de>
Thomas Gleixner [Sun, 8 Apr 2007 22:03:30 +0000 (00:03 +0200)]
prevent timespec/timeval to ktime_t overflow
Frank v. Waveren pointed out that on 64bit machines the timespec to
ktime_t conversion might overflow. This is also true for timeval to
time_t conversions. This breaks a "sleep inf" on 64bit machines.
While a timespec/timeval with tx.sec = MAX_LONG is valid by specification
the internal representation of ktime_t is based on nanoseconds. The
conversion of seconds to nanoseconds overflows for seconds values >=
(MAX_LONG / NSEC_PER_SEC).
Check the seconds argument to the conversion and limit it to the maximum
time which can be represented by ktime_t.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Adrian Bunk <bunk@stusta.de>
David Moore [Sun, 8 Apr 2007 21:54:41 +0000 (23:54 +0200)]
ieee1394: video1394: DMA fix
This together with the phys_to_virt fix in lib/swiotlb.c::swiotlb_sync_sg
fixes video1394 DMA on machines with DMA bounce buffers, especially Intel
x86-64 machines with > 3GB RAM.
Signed-off-by: David Moore <dcm@acm.org> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Adrian Bunk <bunk@stusta.de>
Fix reparenting to the same thread group. (take 2)
This patch fixes the case when we reparent to a different thread in the
same thread group. This modifies the code so that we do not send
signals and do not change the signal to send to SIGCHLD unless we have
change the thread group of our parents. It also suppresses sending
pdeath_sig in this cas as well since the result of geppid doesn't
change.
Thanks to Oleg for spotting my bug of only fixing this for non-ptraced
tasks.
This fixes the issues identified by Albert Cahalan in thread
http://lkml.org/lkml/2006/12/21/22
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: Adrian Bunk <bunk@stusta.de>
Doug Leith observed a discrepancy between the version of CUBIC described
in the papers and the version in 2.6.18. A math error related to scaling
causes Cubic to grow too slowly.
Patch is from "Sangtae Ha" <sha2@ncsu.edu>. I validated that
it does fix the problems.
See the following to show behavior over 500ms 100 Mbit link.
Alan Cox [Wed, 4 Apr 2007 19:34:22 +0000 (21:34 +0200)]
ide-floppy: Fix unformatted media crash
A ZIP or similar with unformatted media will cause crashes when attempts
are made to read/write it in some cases. This is because bs_factor is
zero and we divide by it causing an oops.
As the size of a non-accessible/non-existant media is really a bit of a
zen question it doesn't matter if non-existant media is 512 bytes per
sector or zero. Setting it to 1 causes us to generate 512 bytes/sector
accesses and error properly.
Based on a fix found lurking in an ancient bugzilla entry since about 2004 (ugghhh)
Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Adrian Bunk <bunk@stusta.de>
Patrick McHardy [Tue, 3 Apr 2007 02:03:55 +0000 (04:03 +0200)]
[IFB]: Fix crash on input device removal
The input_device pointer is not refcounted, which means the device may
disappear while packets are queued, causing a crash when ifb passes packets
with a stale skb->dev pointer to netif_rx().
Fix by storing the interface index instead and do a lookup where neccessary.
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: Adrian Bunk <bunk@stusta.de>
David S. Miller [Mon, 2 Apr 2007 23:50:31 +0000 (01:50 +0200)]
[VIDEO] ffb: Fix two DAC handling bugs.
The determination of whether the DAC has inverted cursor logic is
broken, import the version checks the X.org driver uses to fix this.
Next, when we change the timing generator, borrow code from X.org that
does 10 NOP reads of the timing generator register afterwards to make
sure the video-enable transition occurs cleanly.
Finally, use macros for the DAC registers and fields in order to
provide documentation for the next person who reads this code.
Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Adrian Bunk <bunk@stusta.de>
Eric Sesterhenn [Wed, 28 Mar 2007 20:35:52 +0000 (22:35 +0200)]
[ALSA] fix NULL pointer dereference in sound/synth/emux/soundfont.c
this is about coverity id #100.
It seems the if statement is negated, since the else branch calls
remove_info() with sflist->currsf as a parameter where it gets
dereferenced.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Adrian Bunk <bunk@stusta.de>
Takashi Iwai [Wed, 28 Mar 2007 20:29:24 +0000 (22:29 +0200)]
[ALSA] hda-intel - Don't try to probe invalid codecs
Fix the max number of codecs detected by HD-intel (and compatible)
controllers.
ATI controllers may have up to 4 codecs while ICH up to 3.
Now max codecs is defined according to the driver type, either 3 or 4.
Currently 4 is set only to ATI chips. Other might need the same
change, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Adrian Bunk <bunk@stusta.de>
Takashi Iwai [Wed, 28 Mar 2007 20:28:59 +0000 (22:28 +0200)]
[ALSA] hda-codec - Don't return error at initialization of modem codec
Some modem codec seem to fail in the initialization, and this
stopped loading of the whole module although the audio is OK.
Since it's usually a non-fatal issue, the driver tries to proceed
to initialize now.
Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Adrian Bunk <bunk@stusta.de>
[IPV6] HASHTABLES: Use appropriate seed for caluculating ehash index.
Tetsuo Handa <handat@pm.nttdata.co.jp> told me that connect(2) with TCPv6
socket almost always took a few minutes to return when we did not have any
ports available in the range of net.ipv4.ip_local_port_range.
The reason was that we used incorrect seed for calculating index of
hash when we check established sockets in __inet6_check_established().
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Adrian Bunk <bunk@stusta.de>
Patrick McHardy [Wed, 28 Mar 2007 19:58:20 +0000 (21:58 +0200)]
[NET_SCHED]: Fix ingress locking
Ingress queueing uses a seperate lock for serializing enqueue operations,
but fails to properly protect itself against concurrent changes to the
qdisc tree. Use queue_lock for now since the real fix it quite intrusive.
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Adrian Bunk <bunk@stusta.de>
cls_basic doesn't allocate tp->root before it is linked into the
active classifier list, resulting in a NULL pointer dereference
when packets hit the classifier before its ->change function is
called.
Reported by Chris Madden <chris@reflexsecurity.com>
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Marcelo Ricardo Leitner <mrl@mandriva.com> Signed-off-by: Luiz Fernando N. Capitulino <lcapitulino@mandriva.com.br> Signed-off-by: Adrian Bunk <bunk@stusta.de>
Patrick McHardy [Wed, 28 Mar 2007 19:31:36 +0000 (21:31 +0200)]
[NET_SCHED]: Fix endless loops caused by inaccurate qlen counters
There are multiple problems related to qlen adjustment that can lead
to an upper qdisc getting out of sync with the real number of packets
queued, leading to endless dequeueing attempts by the upper layer code.
All qdiscs must maintain an accurate q.qlen counter. There are basically
two groups of operations affecting the qlen: operations that propagate
down the tree (enqueue, dequeue, requeue, drop, reset) beginning at the
root qdisc and operations only affecting a subtree or single qdisc
(change, graft, delete class). Since qlen changes during operations from
the second group don't propagate to ancestor qdiscs, their qlen values
become desynchronized.
This patch adds a function to propagate qlen changes up the qdisc tree,
optionally calling a callback function to perform qdisc-internal
maintenance when the child qdisc is deactivated, and converts all
qdiscs to use this where necessary.
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: Adrian Bunk <bunk@stusta.de>
Russell King [Wed, 28 Mar 2007 19:28:32 +0000 (21:28 +0200)]
[SERIAL] Fix oops when removing suspended serial port
A serial card might have been removed when the system is resumed.
This results in a suspended port being shut down, which results in
the ports shutdown method being called twice in a row. This causes
BUGs. Avoid this by tracking the suspended state separately from
the initialised state.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Adrian Bunk <bunk@stusta.de>
Neil Brown [Mon, 26 Mar 2007 21:40:42 +0000 (23:40 +0200)]
MD: Fix problem where hot-added drives are not resynced.
If a drive is added with HOT_ADD_DISK rather than ADD_NEW_DISK,
saved_raid_disk isn't initialised properly, and the drive can be
included in the array without a resync.
Pete Zaitcev [Sun, 25 Mar 2007 01:24:11 +0000 (03:24 +0200)]
USB: unusual_devs.h for 0x046b:ff40
American Megatrends did something wrong in their floppy emulator. It breaks
with both kinds of MODE SENSE which our stack sends. Alan and I tried a few
tweaks, and got LUNs sensed right, but US_FL_NO_WP_DETECT is still needed.
I set the firmware bracket to 1.00 exactly, in case AMI or Sun fix it with a
firmware update. Hey, you never know.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com> Signed-off-by: Phil Dibowitz <phil@ipom.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Adrian Bunk <bunk@stusta.de>
Phil Dibowitz [Sun, 25 Mar 2007 01:23:20 +0000 (03:23 +0200)]
USB: Fix UCR-61S2B unusual_dev entry
Recently this entry's bcd scope was narrowed so as not to falsly apply
to bcd's other than 0x0110. But while it breaks those of a larger bcd,
it is still needed for those of a smaller bcd - so this changes the
lower bcd limit to 0x0000.
Signed-off-by: Phil Dibowitz <phil@ipom.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Adrian Bunk <bunk@stusta.de>
Alan Stern [Sun, 25 Mar 2007 01:22:24 +0000 (03:22 +0200)]
unusual_devs update for UCR-61S2B
The existing unusual_devs entry for the UCR-61S2B appears to have too
wide a revision range. It matches at least one device that doesn't
respond to the initialization sequence. Perhaps the sequence needs to
be updated, or perhaps something else can be done. For now, this patch
(as764) restricts the range to include only the revision mentioned in
the original comment.
This resolves (for now!) Bugzilla entry #6950.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Adrian Bunk <bunk@stusta.de>
Jaco Kroon [Sun, 25 Mar 2007 01:14:22 +0000 (03:14 +0200)]
USB: add Digitech USB-Storage to unusual_devs.h
The mass storage device from Digitech designed for Flash Cards, as found
on (for example) the GNX4 device has issues with residue, similar to the
bug report at http://kerneltrap.org/node/6297. This patch adds the
faulty storage device to unusual_devs.h, this not only reduces the noise
in dmesg but also increases the transfer speeds by a factor of 7x for me
(89kB/s -> 637kB/s).
Phil Dibowitz [Sun, 25 Mar 2007 01:10:17 +0000 (03:10 +0200)]
USB: usb-storage: Unusual_dev update
The protocol in this entry is needed for some versions of the device but
not others. This adds the NEED_OVERRIDE flag to prevent it complaining
to users who don't need it.
Signed-off-by: Phil Dibowitz <phil@ipom.com> Signed-off-by: Adrian Bunk <bunk@stusta.de>
Alan Stern [Sun, 25 Mar 2007 01:02:24 +0000 (03:02 +0200)]
USB: unusual_devs entry for Lacie DVD+-RW
This patch (as781) adds an entry to unusual_devs.h for the Lacie DVD+-RW
drive. Apparently its USB interface has requirements similar to the
Genesys Logic interface; it doesn't like data to be sent too soon after
a command.
This fixes Bugzilla #6817.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Phil Dibowitz <phil@ipom.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Adrian Bunk <bunk@stusta.de>
Alan Stern [Sun, 25 Mar 2007 00:55:30 +0000 (01:55 +0100)]
USB: unusual_devs entry for Nokia N91
This patch (as745) adds an unusual_devs entry for the Nokia N91, just like
the entry for the N80 added a couple of weeks ago. Apparently Nokia isn't
using very good firmware these days...
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Adrian Bunk <bunk@stusta.de>
Phil Dibowitz [Sun, 25 Mar 2007 00:54:59 +0000 (01:54 +0100)]
USB Storage: US_FL_MAX_SECTORS_64 flag
This patch adds a US_FL_MAX_SECTORS_64 and removes the Genesys special-cases
for this that were in scsiglue.c. It also adds the flag to other devices
reported to need it.
Signed-off-by: Phil Dibowitz <phil@ipom.com> Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Adrian Bunk <bunk@stusta.de>
Alan Stern [Sun, 25 Mar 2007 00:52:12 +0000 (01:52 +0100)]
usb-storage: unusual_devs entry for Nikon DSC D70s
This patch (as704) adds an unusual_devs entry for the Nikon DSC D70s,
which uses a different Product ID from the D70. It also moves the entry
for the DSC E2000 up in the list, to preserve the numerical ordering.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Adrian Bunk <bunk@stusta.de>
Phil Dibowitz [Sun, 25 Mar 2007 00:50:55 +0000 (01:50 +0100)]
USB: Storage: unusual devs update
This patch removes the Protocol portion of the Iomega Click! device as it's not
needed. Not-needed message reported by Kenneth Crudup <kenny@panix.com>
Signed-off-by: Phil Dibowitz <phil@ipom.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Adrian Bunk <bunk@stusta.de>
Phil Dibowitz [Sun, 25 Mar 2007 00:48:23 +0000 (01:48 +0100)]
USB: storage: sandisk unusual_devices entry
The following adds an unusual_devs entry for the SanDisk ImageMate CompactFlash
USB drive, for the US_FL_FIX_CAPACITY flag. Additionally, it removes trailing
whitespace from the previous entry. It's based on the patch sent by Roman Hodek
<roman@hodek.net>.
Signed-off-by: Phil Dibowitz <phil@ipom.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Adrian Bunk <bunk@stusta.de>
Patrick McHardy [Sat, 24 Mar 2007 20:30:53 +0000 (21:30 +0100)]
[NETFILTER]: nfnetlink_log: fix crash on bridged packet
physoutdev is only set on purely bridged packet, when nfnetlink_log is used
in the OUTPUT/FORWARD/POSTROUTING hooks on packets forwarded from or to a
bridge it crashes when trying to dereference skb->nf_bridge->physoutdev.
Reported by Holger Eitzenberger <heitzenberger@astaro.com>
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: Adrian Bunk <bunk@stusta.de>
Patrick McHardy [Sat, 24 Mar 2007 20:30:06 +0000 (21:30 +0100)]
[NETFILTER]: nf_conntrack: fix incorrect classification of IPv6 fragments as ESTABLISHED
The individual fragments of a packet reassembled by conntrack have the
conntrack reference from the reassembled packet attached, but nfctinfo
is not copied. This leaves it initialized to 0, which unfortunately is
the value of IP_CT_ESTABLISHED.
The result is that all IPv6 fragments are tracked as ESTABLISHED,
allowing them to bypass a usual ruleset which accepts ESTABLISHED
packets early.
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: Adrian Bunk <bunk@stusta.de>
Patrick McHardy [Sat, 24 Mar 2007 20:26:20 +0000 (21:26 +0100)]
NETFILTER: xt_connbytes: fix division by zero
When the packet counter of a connection is zero a division by zero
occurs in div64_64(). Fix that by using zero as average value, which
is correct as long as the packet counter didn't overflow, at which
point we have lost anyway.
Based on patch from Jonas Berlin <xkr47@outerspace.dyndns.org>,
with suggestions from KOVACS Krisztian <hidden@balabit.hu>.
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: Adrian Bunk <bunk@stusta.de>
Patrick McHardy [Sat, 24 Mar 2007 20:22:33 +0000 (21:22 +0100)]
NETFILTER: nf_conntrack_ipv6: fix crash when handling fragments
When IPv6 connection tracking splits up a defragmented packet into
its original fragments, the packets are taken from a list and are
passed to the network stack with skb->next still set. This causes
dev_hard_start_xmit to treat them as GSO fragments, resulting in
a use after free when connection tracking handles the next fragment.
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: Adrian Bunk <bunk@stusta.de>
Patrick McHardy [Sat, 24 Mar 2007 20:22:09 +0000 (21:22 +0100)]
NETFILTER: Fix iptables ABI breakage on (at least) CRIS
With the introduction of x_tables we accidentally broke compatibility
by defining IPT_TABLE_MAXNAMELEN to XT_FUNCTION_MAXNAMELEN instead of
XT_TABLE_MAXNAMELEN, which is two bytes larger.
On most architectures it doesn't really matter since we don't have
any tables with names that long in the kernel and the structure
layout didn't change because of alignment requirements of following
members. On CRIS however (and other architectures that don't align
data) this changed the structure layout and thus broke compatibility
with old iptables binaries.
Changing it back will break compatibility with binaries compiled
against recent kernels again, but since the breakage has only been
there for three releases this seems like the better choice.
Spotted by Jonas Berlin <xkr47@outerspace.dyndns.org>.
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: Adrian Bunk <bunk@stusta.de>
Patrick McHardy [Sat, 24 Mar 2007 20:18:01 +0000 (21:18 +0100)]
NETFILTER: Kconfig: fix xt_physdev dependencies
xt_physdev depends on bridge netfilter, which is a boolean, but can still
be built modular because of special handling in the bridge makefile. Add
a dependency on BRIDGE to prevent XT_MATCH_PHYSDEV=y, BRIDGE=m.
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: Adrian Bunk <bunk@stusta.de>
Ed Swierk [Tue, 20 Mar 2007 23:28:30 +0000 (00:28 +0100)]
load_module: no BUG if module_subsys uninitialized
Invoking load_module() before param_sysfs_init() is called crashes in
mod_sysfs_setup(), since the kset in module_subsys is not initialized yet.
In my case, net-pf-1 is getting modprobed as a result of hotplug trying to
create a UNIX socket. Calls to hotplug begin after the topology_init
initcall.
Another patch for the same symptom (module_subsys-initialize-earlier.patch)
moves param_sysfs_init() to the subsys initcalls, but this is still not
early enough in the boot process in some cases. In particular,
topology_init() causes /sbin/hotplug to run, which requests net-pf-1 (the
UNIX socket protocol) which can be compiled as a module. Moving
param_sysfs_init() to the postcore initcalls fixes this particular race,
but there might well be other cases where a usermodehelper causes a module
to load earlier still.
The patch makes load_module() return an error rather than crashing the
kernel if invoked before module_subsys is initialized.
projects / karo-tx-linux.git / log