This adds a fairly simple xhci-platform driver support. Currently it is
used by the dwc3 driver for supporting host mode.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Andiry Xu [Mon, 5 Mar 2012 09:49:40 +0000 (17:49 +0800)]
xHCI: check enqueue pointer advance into dequeue seg
When a urb is submitted to xHCI driver, check if queueing the urb will make
the enqueue pointer advance into dequeue seg and expand the ring if it
occurs. This is to guarantee the safety of ring expansion.
Signed-off-by: Andiry Xu <andiry.xu@amd.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Tested-by: Paul Zimmerman <Paul.Zimmerman@synopsys.com>
Andiry Xu [Mon, 5 Mar 2012 09:49:37 +0000 (17:49 +0800)]
xHCI: dynamic ring expansion
If room_on_ring() check fails, try to expand the ring and check again.
When expand a ring, use a cached ring or allocate new segments, link
the original ring and the new ring or segments, update the original ring's
segment numbers and the last segment pointer.
Signed-off-by: Andiry Xu <andiry.xu@amd.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Tested-by: Paul Zimmerman <Paul.Zimmerman@synopsys.com>
Andiry Xu [Mon, 5 Mar 2012 09:49:36 +0000 (17:49 +0800)]
xHCI: set cycle state when allocate rings
In the past all the rings were allocated with cycle state equal to 1.
Now the driver may expand an existing ring, and the new segments shall be
allocated with the same cycle state as the old one.
This affects ring allocation and cached ring re-initialization.
Signed-off-by: Andiry Xu <andiry.xu@amd.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Tested-by: Paul Zimmerman <Paul.Zimmerman@synopsys.com>
Andiry Xu [Mon, 5 Mar 2012 09:49:34 +0000 (17:49 +0800)]
xHCI: count free TRBs on transfer ring
In the past, the room_on_ring() check was implemented by walking all over
the ring, which is wasteful and complicated.
Count the number of free TRBs instead. The free TRBs number should be
updated when enqueue/dequeue pointer is updated, or upon the completion
of a set dequeue pointer command.
Signed-off-by: Andiry Xu <andiry.xu@amd.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Tested-by: Paul Zimmerman <Paul.Zimmerman@synopsys.com>
Felipe Balbi [Fri, 27 Jan 2012 14:19:15 +0000 (16:19 +0200)]
usb: host: xhci: use __ffs() instead of hardcoding shift
__ffs() can tell us which is the SEGMENT_SHIFT value
to be used. This will prevent problems when users are
too fast and don't pay attention to the need of fixing
the Shift after changing TRBS_PER_SEGMENT.
Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Andiry Xu [Mon, 12 Dec 2011 08:45:28 +0000 (16:45 +0800)]
xHCI: BESL calculation based on USB2.0 LPM errata
The latest released errata for USB2.0 ECN LPM adds new fields to USB2.0
extension descriptor, defines two BESL values for device: baseline BESL
and deep BESL. Baseline BESL value communicates a nominal power savings
design point and the deep BESL value communicates a significant power
savings design point.
If device indicates BESL value, driver will use a value count in both
host BESL and device BESL. Use baseline BESL value as default.
Signed-off-by: Andiry Xu <andiry.xu@amd.com> Tested-by: Jason Fan <jcfan@qca.qualcomm.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Al Viro [Thu, 8 Mar 2012 17:51:19 +0000 (17:51 +0000)]
aio: fix the "too late munmap()" race
Current code has put_ioctx() called asynchronously from aio_fput_routine();
that's done *after* we have killed the request that used to pin ioctx,
so there's nothing to stop io_destroy() waiting in wait_for_all_aios()
from progressing. As the result, we can end up with async call of
put_ioctx() being the last one and possibly happening during exit_mmap()
or elf_core_dump(), neither of which expects stray munmap() being done
to them...
We do need to prevent _freeing_ ioctx until aio_fput_routine() is done
with that, but that's all we care about - neither io_destroy() nor
exit_aio() will progress past wait_for_all_aios() until aio_fput_routine()
does really_put_req(), so the ioctx teardown won't be done until then
and we don't care about the contents of ioctx past that point.
Since actual freeing of these suckers is RCU-delayed, we don't need to
bump ioctx refcount when request goes into list for async removal.
All we need is rcu_read_lock held just over the ->ctx_lock-protected
area in aio_fput_routine().
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Reviewed-by: Jeff Moyer <jmoyer@redhat.com> Acked-by: Benjamin LaHaise <bcrl@kvack.org> Cc: stable@vger.kernel.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Al Viro [Wed, 7 Mar 2012 05:16:35 +0000 (05:16 +0000)]
aio: fix io_setup/io_destroy race
Have ioctx_alloc() return an extra reference, so that caller would drop it
on success and not bother with re-grabbing it on failure exit. The current
code is obviously broken - io_destroy() from another thread that managed
to guess the address io_setup() would've returned would free ioctx right
under us; gets especially interesting if aio_context_t * we pass to
io_setup() points to PROT_READ mapping, so put_user() fails and we end
up doing io_destroy() on kioctx another thread has just got freed...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Acked-by: Benjamin LaHaise <bcrl@kvack.org> Reviewed-by: Jeff Moyer <jmoyer@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sat, 10 Mar 2012 02:09:18 +0000 (18:09 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs updates from Chris Mason:
"I have two additional and btrfs fixes in my for-linus branch. One is
a casting error that leads to memory corruption on i386 during scrub,
and the other fixes a corner case in the backref walking code (also
triggered by scrub)."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: fix casting error in scrub reada code
btrfs: fix locking issues in find_parent_nodes()
driver-core: Allow additional parameters for module_driver
Allow module_driver take additional parameters which will be passed to the
register and unregister function calls. This allows it to be used in cases
where additional parameters are required (e.g. usb_serial_register_drivers).
Hugh Dickins [Fri, 9 Mar 2012 21:37:32 +0000 (13:37 -0800)]
memcg: revert fix to mapcount check for this release
Respectfully revert commit e6ca7b89dc76 "memcg: fix mapcount check
in move charge code for anonymous page" for the 3.3 release, so that
it behaves exactly like releases 2.6.35 through 3.2 in this respect.
Horiguchi-san's commit is correct in itself, 1 makes much more sense
than 2 in that check; but it does not go far enough - swapcount
should be considered too - if we really want such a check at all.
We appear to have reached agreement now, and expect that 3.4 will
remove the mapcount check, but had better not make 3.3 different.
Bjørn Mork [Fri, 9 Mar 2012 11:35:06 +0000 (12:35 +0100)]
net: qmi_wwan: add Gobi and Pantech UML290 device IDs
Adding the Pantech UML290 and all non-QDL Gobi device IDs from the
qcserial driver now that we have support for shared net/QMI USB
interfaces. Most of these are not yet tested with this driver, but
should be mostly identical to tested devices, except for device IDs.
Gobi devices provide several different interfaces (serial/net/other)
using the exact same class, subclass and protocol values. This driver
will only support the net/QMI function while there are other drivers
supporting other device functions. The net/QMI interface number may
also differ from device to device. It has been noted that all the
other interfaces have additional functional descriptors, so we use that
to detect the interface supported by this driver.
Bjørn Mork [Fri, 9 Mar 2012 11:35:05 +0000 (12:35 +0100)]
net: qmi_wwan: support devices having a shared QMI/wwan interface
Use the new cdc-wdm subdriver interface to create a device management
device even for USB devices having a single combined QMI/wwan USB
interface with three endpoints (int, bulk in, bulk out) instead of
separate data and control interfaces.
Some Huawei devices can be switched to a single interface mode for
use with other operating systems than Linux. This adds support
for these devices when they run in such non-Linux modes.
Bjørn Mork [Thu, 19 Jan 2012 15:37:22 +0000 (15:37 +0000)]
net: usb: qmi_wwan: New driver for Huawei QMI based WWAN devices
Some WWAN LTE/3G devices based on chipsets from Qualcomm provide
near standard CDC ECM interfaces in addition to the usual serial
interfaces. The Huawei E392/E398 are examples of such devices.
These typically cannot be fully configured using AT commands
over a serial interface. It is necessary to speak the proprietary
Qualcomm MSM Interface (QMI) protocol to the device to enable the
ethernet proxy functionality.
The devices embed the QMI protocol in CDC on the control interface,
using standard CDC commands and notifications. The do not otherwise
use CDC commands for the ethernet function. This driver does
therefore not need access to any other aspects of the control
interface than the descriptors attached to it.
Another driver, cdc-wdm, will provide userspace access to the
QMI protocol independently of this driver. To facilitate this,
this driver avoids binding to the control interface, and uses
only the associated data interface after parsing the common CDC
functional descriptors on the control interface.
You will want both the cdc-wdm and option drivers as companions to
this driver, to have full access to all interfaces and protocols
exported by the device.
Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thomas Gleixner [Fri, 9 Mar 2012 19:55:10 +0000 (20:55 +0100)]
x86: Derandom delay_tsc for 64 bit
Commit f0fbf0abc093 ("x86: integrate delay functions") converted
delay_tsc() into a random delay generator for 64 bit. The reason is
that it merged the mostly identical versions of delay_32.c and
delay_64.c. Though the subtle difference of the result was:
static void delay_tsc(unsigned long loops)
{
- unsigned bclock, now;
+ unsigned long bclock, now;
Now the function uses rdtscl() which returns the lower 32bit of the
TSC. On 32bit that's not problematic as unsigned long is 32bit. On 64
bit this fails when the lower 32bit are close to wrap around when
bclock is read, because the following check
if ((now - bclock) >= loops)
break;
evaluated to true on 64bit for e.g. bclock = 0xffffffff and now = 0
because the unsigned long (now - bclock) of these values results in
0xffffffff00000001 which is definitely larger than the loops
value. That explains Tvortkos observation:
"Because I am seeing udelay(500) (_occasionally_) being short, and
that by delaying for some duration between 0us (yep) and 491us."
Make those variables explicitely u32 again, so this works for both 32
and 64 bit.
Linus Torvalds [Fri, 9 Mar 2012 20:14:23 +0000 (12:14 -0800)]
Merge tag 'sound-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Nothing exciting here: just a few regression fixes for HD-audio and
ASoC, also the support of missing 32bit compat ioctl for HDSPM."
* tag 'sound-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hdspm - Provide ioctl_compat
ALSA: hda/realtek - Apply the coef-setup only to ALC269VB
ALSA: hda - add quirk to detect CD input on Gigabyte EP45-DS3
ASoC: neo1973: fix neo1973 wm8753 initialization
Linus Torvalds [Fri, 9 Mar 2012 15:26:25 +0000 (07:26 -0800)]
Merge tag 'iommu-fixes-v3.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull two IOMMU fixes from Joerg Roedel:
"The first is an additional fix for the OMAP initialization order issue
and the second patch fixes a possible section mismatch which can lead
to a kernel crash in the AMD IOMMU driver when suspend/resume is used
and the compiler has not inlined the iommu_set_device_table function."
* tag 'iommu-fixes-v3.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
x86/amd: iommu_set_device_table() must not be __init
ARM: OMAP: fix iommu, not mailbox
Linus Torvalds [Fri, 9 Mar 2012 15:23:17 +0000 (07:23 -0800)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull radeon drm stuff from Dave Airlie:
"Just some radeon fixes, one is for an oops where we run out of ioremap
space on some big hardware systems in 32-bit mode, stuff doesn't work
properly but at least the machine will boot.
One regression fix, and two bugs, one hw, one blit code."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon/kms: fix hdmi duallink checks
drm/radeon/kms: set SX_MISC in the r6xx blit code (v2)
drm/radeon: deal with errors from framebuffer init path.
drm/radeon: fix a semaphore deadlock on pre cayman asics
1) IPV4 routing metrics can become stale when routes are changed by the
administrator, fix from Steffen Klassert.
2) atl1c does "val |= XXX;" where XXX is a bit number not a bit mask,
fix by using set_bit. From Dan Carpenter.
3) Memory accounting bug in carl9170 driver results in wedged TX queue.
Fix from Nicolas Cavallari.
4) iwlwifi accidently uses "sizeof(ptr)" instead of "sizeof(*ptr)", fix
from Johannes Berg.
5) Openvswitch doesn't honor dp_ifindex when doing vport lookups, fix
from Ben Pfaff.
6) ehea conversion to 64-bit stats lost multicast and rx_errors
accounting, fix from Eric Dumazet.
7) Bridge state transition logging in br_stp_disable_port() is busted,
it's emitted at the wrong time and the message is in the wrong tense,
fix from Paulius Zaleckas.
8) mlx4 device erroneously invokes the queue resize firmware operation
twice, fix from Jack Morgenstein.
9) Fix deadlock in usbnet, need to drop lock when invoking usb_unlink_urb()
otherwise we recurse into taking it again. Fix from Sebastian Siewior.
10) hyperv network driver uses the wrong driver name string, fix from
Haiyang Zhang.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
net/hyperv: Use the built-in macro KBUILD_MODNAME for this driver
net/usbnet: avoid recursive locking in usbnet_stop()
route: Remove redirect_genid
inetpeer: Invalidate the inetpeer tree along with the routing cache
mlx4_core: fix bug in modify_cq wrapper for resize flow.
atl1c: set ATL1C_WORK_EVENT_RESET bit correctly
bridge: fix state reporting when port is disabled
bridge: br_log_state() s/entering/entered/
ehea: restore multicast and rx_errors fields
openvswitch: Fix checksum update for actions on UDP packets.
openvswitch: Honor dp_ifindex, when specified, for vport lookup by name.
iwlwifi: fix wowlan suspend
mwifiex: reset encryption mode flag before association
carl9170: fix frame delivery if sta is in powersave mode
carl9170: Fix memory accounting when sta is in power-save mode.
Linus Torvalds [Fri, 9 Mar 2012 01:32:42 +0000 (17:32 -0800)]
Merge tag 'fixes-urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull last minute fixes from Olof Johansson:
"One samsung build fix due to a mis-applied patch, and a small set of
OMAP fixes. This should be the last from arm-soc for 3.3, hopefully."
* tag 'fixes-urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: S3C2440: Fixed build error for s3c244x
ARM: OMAP2+: Fix module build errors with CONFIG_OMAP4_ERRATA_I688
ARM: OMAP: id: Add missing break statement in omap3xxx_check_revision
ARM: OMAP2+: Remove apply_uV constraints for fixed regulator
ARM: OMAP: irqs: Fix NR_IRQS value to handle PRCM interrupts
Linus Torvalds [Fri, 9 Mar 2012 01:25:17 +0000 (17:25 -0800)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fix from Mark Brown:
"Another small, clear fix in a specific driver."
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: tps65910: Configure correct value for VDDCTRL vout reg
Linus Torvalds [Fri, 9 Mar 2012 01:24:27 +0000 (17:24 -0800)]
Merge tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux-2.6
Pull minor devicetree bug fixes and documentation updates from Grant Likely:
"Fixes up a duplicate #include, adds an empty implementation of
of_find_compatible_node() and make git ignore .dtb files. And fix up
bus name on OF described PHYs. Nothing exciting here."
* tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux-2.6:
doc: dt: Fix broken reference in gpio-leds documentation
of/mdio: fix fixed link bus name
of/fdt.c: asm/setup.h included twice
of: add picochip vendor prefix
dt: add empty of_find_compatible_node function
ARM: devicetree: Add .dtb files to arch/arm/boot/.gitignore
Linus Torvalds [Fri, 9 Mar 2012 01:22:54 +0000 (17:22 -0800)]
Merge tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull four hwmon patches from Guenter Roeck
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (jc42) Add support for AT30TS00, TS3000GB2, TSE2002GB2, and MCP9804
hwmon: (zl6100) Maintain delay parameter in driver instance data
hwmon: (pmbus_core) Fix maximum number of POUT alarm attributes
hwmon: (jc42) Add support for ST Microelectronics STTS2002 and STTS3000
Linus Torvalds [Fri, 9 Mar 2012 01:21:51 +0000 (17:21 -0800)]
Merge tag 'dm-3.3-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm
Pull device-mapper fixes for 3.3 from Alasdair Kergon
Eight small device-mapper bug fixes.
* tag 'dm-3.3-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm:
dm raid: fix flush support
dm raid: set MD_CHANGE_DEVS when rebuilding
dm thin metadata: decrement counter after removing mapped block
dm thin metadata: unlock superblock in init_pmd error path
dm thin metadata: remove incorrect close_device on creation error paths
dm flakey: fix crash on read when corrupt_bio_byte not set
dm io: fix discard support
dm ioctl: do not leak argv if target message only contains whitespace
Haiyang Zhang [Wed, 7 Mar 2012 10:02:00 +0000 (10:02 +0000)]
net/hyperv: Use the built-in macro KBUILD_MODNAME for this driver
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Cc: Olaf Hering <olaf@aepfle.de> Signed-off-by: David S. Miller <davem@davemloft.net>
USB: serial: metro-usb: fix up coding style errors
This fixes up all of the coding style errors, and removes the initial,
unneeded comments on how to load the module and the old changelog which
are no longer needed.
There are still a number of coding style warnings left, I'll get to them
later.
A driver doesn't need a .h file just for simple things like vendor ids
and a private structure. So move it into the .c file instead, saving
some overall lines.
USB: serial: metro-usb: convert to use module_usb_serial_driver
Now that we aren't doing anything special in the init function, move to
use the easier module_usb_serial_driver() call instead, saving a lot of
lines of unnecessary code.
USB: serial: metro-usb: remove vendor and product module parameters
All new usb serial drivers should be using the dynamic id function, not
having module parameters for this type of thing. So remove them before
anyone gets used to them being there.
USB: serial: metro-usb: fix up usb_serial_register calls
The usb serial core has changed how the driver is to be registered and
unregistered recently. Make these changes to the driver so that it will
properly build and work.
Orjan Friberg [Wed, 7 Mar 2012 16:16:14 +0000 (17:16 +0100)]
USB: gadget: Make g_hid device class conform to spec.
HID devices should specify this in their interface descriptors, not in the
device descriptor. This fixes a "missing hardware id" bug under Windows 7 with
a VIA VL800 (3.0) controller.
Bjørn Mork [Tue, 6 Mar 2012 16:29:22 +0000 (17:29 +0100)]
usb: cdc-wdm: adding usb_cdc_wdm_register subdriver support
This driver can be used as a subdriver of another USB driver, allowing
it to export a Device Managment interface consisting of a single interrupt
endpoint with no dedicated USB interface.
Some devices provide a Device Management function combined with a wwan
function in a single USB interface having three endpoints (bulk in/out
+ interrupt). If the interrupt endpoint is used exclusively for DM
notifications, then this driver can support that as a subdriver
provided that the wwan driver calls the appropriate entry points on
probe, suspend, resume, pre_reset, post_reset and disconnect.
The main driver must have full control over all interface related
settings, including the needs_remote_wakeup flag. A manage_power
function must be provided by the main driver.
A manage_power stub doing direct flag manipulation is used in normal
driver mode.
Bjørn Mork [Tue, 6 Mar 2012 16:29:21 +0000 (17:29 +0100)]
usb: cdc-wdm: adding list lookup indirection
Register all interfaces handled by this driver in a list, getting
rid of the dependency on usb_set_intfdata. This allows further
generalization and simplification of the probe/create functions.
This is needed to decouple wdm_open from the driver owning the
interface, and it also allows us to share all the code in
wdm_create with drivers unable to do usb_set_intfdata.
Bjørn Mork [Tue, 6 Mar 2012 16:29:20 +0000 (17:29 +0100)]
usb: cdc-wdm: split out reusable parts of probe
Preparing for the addition of subdriver registering as an alternative
to probe for interface-less usage. This should not change anything
apart from minor code reordering.
Jingoo Han [Mon, 5 Mar 2012 01:40:14 +0000 (10:40 +0900)]
USB: ehci-s5p: add DMA burst support
DMA burst support is added to improve performance in EHCI data
transfer. The USB EHCI controller on Exynos SoCs can use INCR16,
INCR8, and INCR4 mode. These modes of INSNREG00 register should
be set in order to enable DMA burst transfer. This feature is
also related to AHB spec.
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Sangwook Lee <sangwook.lee@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kukjin Kim [Thu, 8 Mar 2012 09:48:36 +0000 (01:48 -0800)]
ARM: S3C2440: Fixed build error for s3c244x
Fixed following:
arch/arm/mach-s3c2440/s3c244x.c: In function 's3c244x_restart':
arch/arm/mach-s3c2440/s3c244x.c:209: error: expected declaration or statement at end of input
make[1]: *** [arch/arm/mach-s3c24xx/s3c244x.o] Error 1
make: *** [arch/arm/mach-s3c24xx] Error 2
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com> Signed-off-by: Olof Johansson <olof@lixom.net>
Adrian Knoth [Thu, 8 Mar 2012 14:38:04 +0000 (15:38 +0100)]
ALSA: hdspm - Provide ioctl_compat
snd_hdspm uses its own ioctls to acquire config- and status information.
Expose the corresponding ioctl handler via ioctl_compat, so that 32bit
applications can use it on 64bit kernels.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Marek Olšák [Wed, 7 Mar 2012 22:33:00 +0000 (23:33 +0100)]
drm/radeon/kms: set SX_MISC in the r6xx blit code (v2)
Mesa may set it to 1, causing all primitives to be killed.
v2: also update the r7xx code
Signed-off-by: Marek Olšák <maraeo@gmail.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@kernel.org Signed-off-by: Dave Airlie <airlied@redhat.com>
net/usbnet: avoid recursive locking in usbnet_stop()
|kernel BUG at kernel/rtmutex.c:724!
|[<c029599c>] (rt_spin_lock_slowlock+0x108/0x2bc) from [<c01c2330>] (defer_bh+0x1c/0xb4)
|[<c01c2330>] (defer_bh+0x1c/0xb4) from [<c01c3afc>] (rx_complete+0x14c/0x194)
|[<c01c3afc>] (rx_complete+0x14c/0x194) from [<c01cac88>] (usb_hcd_giveback_urb+0xa0/0xf0)
|[<c01cac88>] (usb_hcd_giveback_urb+0xa0/0xf0) from [<c01e1ff4>] (musb_giveback+0x34/0x40)
|[<c01e1ff4>] (musb_giveback+0x34/0x40) from [<c01e2b1c>] (musb_advance_schedule+0xb4/0x1c0)
|[<c01e2b1c>] (musb_advance_schedule+0xb4/0x1c0) from [<c01e2ca8>] (musb_cleanup_urb.isra.9+0x80/0x8c)
|[<c01e2ca8>] (musb_cleanup_urb.isra.9+0x80/0x8c) from [<c01e2ed0>] (musb_urb_dequeue+0xec/0x108)
|[<c01e2ed0>] (musb_urb_dequeue+0xec/0x108) from [<c01cbb90>] (unlink1+0xbc/0xcc)
|[<c01cbb90>] (unlink1+0xbc/0xcc) from [<c01cc2ec>] (usb_hcd_unlink_urb+0x54/0xa8)
|[<c01cc2ec>] (usb_hcd_unlink_urb+0x54/0xa8) from [<c01c2a84>] (unlink_urbs.isra.17+0x2c/0x58)
|[<c01c2a84>] (unlink_urbs.isra.17+0x2c/0x58) from [<c01c2b44>] (usbnet_terminate_urbs+0x94/0x10c)
|[<c01c2b44>] (usbnet_terminate_urbs+0x94/0x10c) from [<c01c2d68>] (usbnet_stop+0x100/0x15c)
|[<c01c2d68>] (usbnet_stop+0x100/0x15c) from [<c020f718>] (__dev_close_many+0x94/0xc8)
defer_bh() takes the lock which is hold during unlink_urbs(). The safe
walk suggest that the skb will be removed from the list and this is done
by defer_bh() so it seems to be okay to drop the lock here.
Cc: stable@kernel.org Reported-by: AnÃbal Almeida Pinto <anibal.pinto@efacec.com> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Acked-by: Oliver Neukum <oliver@neukum.org> Signed-off-by: David S. Miller <davem@davemloft.net>
As we invalidate the inetpeer tree along with the routing cache now,
we don't need a genid to reset the redirect handling when the routing
cache is flushed.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: David S. Miller <davem@davemloft.net>
inetpeer: Invalidate the inetpeer tree along with the routing cache
We initialize the routing metrics with the values cached on the
inetpeer in rt_init_metrics(). So if we have the metrics cached on the
inetpeer, we ignore the user configured fib_metrics.
To fix this issue, we replace the old tree with a fresh initialized
inet_peer_base. The old tree is removed later with a delayed work queue.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: David S. Miller <davem@davemloft.net>
mlx4_core: fix bug in modify_cq wrapper for resize flow.
The actual FW command is called in procedure "handle_resize".
Code incorrectly invoked the FW command again (in good flow), in
the modify_cq wrapper function.
Fix by skipping second FW invocation unconditionally for resize.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: David S. Miller <davem@davemloft.net>
Now we have:
eth0: link *down*
br0: port 1(eth0) entered *forwarding* state
br_log_state(p) should be called *after* p->state is set
to BR_STATE_DISABLED.
Reported-by: Zilvinas Valinskas <zilvinas@wilibox.com> Signed-off-by: Paulius Zaleckas <paulius.zaleckas@gmail.com> Acked-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 6 Mar 2012 19:46:41 +0000 (19:46 +0000)]
ehea: restore multicast and rx_errors fields
Commit 239c562c94d (ehea: Add 64bit statistics) added a regression,
since we no longer report multicast & rx_errors fields, taken from
port->stats structure. These fields are updated in ehea_update_stats()
every second.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Cc: Anton Blanchard <anton@samba.org> Cc: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com> Acked-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com> Tested-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jesse Gross [Tue, 6 Mar 2012 23:05:46 +0000 (15:05 -0800)]
openvswitch: Fix checksum update for actions on UDP packets.
When modifying IP addresses or ports on a UDP packet we don't
correctly follow the rules for unchecksummed packets. This meant
that packets without a checksum can be given a incorrect new checksum
and packets with a checksum can become marked as being unchecksummed.
This fixes it to handle those requirements.
Both md and dm have support for flush, but the dm-raid target
forgot to set the flag to indicate that flushes should be
passed on. (Important for data integrity e.g. with writeback cache
enabled.)
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com> Acked-by: Mike Snitzer <snitzer@redhat.com> Cc: stable@kernel.org Signed-off-by: Alasdair G Kergon <agk@redhat.com>
The 'rebuild' parameter is used to rebuild individual devices in an
array (e.g. resynchronize a RAID1 device or recalculate a parity device
in higher RAID). The MD_CHANGE_DEVS flag must be set when this
parameter is given in order to write out the superblocks and make the
change take immediate effect. The code that handles new devices in
super_load already sets MD_CHANGE_DEVS and 'FirstUse'. (The 'FirstUse'
flag was being set as a special case for rebuilds in
super_init_validation.)
Add a condition for rebuilds in super_load to take care of both flags
without the special case in 'super_init_validation'.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com> Cc: stable@kernel.org Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Joe Thornber [Wed, 7 Mar 2012 19:09:44 +0000 (19:09 +0000)]
dm thin metadata: decrement counter after removing mapped block
Correct the number of mapped sectors shown on a thin device's
status line by decrementing td->mapped_blocks in __remove() each time
a block is removed.
Signed-off-by: Joe Thornber <ejt@redhat.com> Acked-by: Mike Snitzer <snitzer@redhat.com> Cc: stable@kernel.org Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Joe Thornber [Wed, 7 Mar 2012 19:09:43 +0000 (19:09 +0000)]
dm thin metadata: unlock superblock in init_pmd error path
If dm_sm_disk_create() fails the superblock must be unlocked.
Signed-off-by: Joe Thornber <ejt@redhat.com> Acked-by: Mike Snitzer <snitzer@redhat.com> Cc: stable@kernel.org Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Mike Snitzer [Wed, 7 Mar 2012 19:09:41 +0000 (19:09 +0000)]
dm thin metadata: remove incorrect close_device on creation error paths
The __open_device() error paths in __create_thin() and __create_snap()
incorrectly call __close_device() even if td was not initialized by
__open_device(). Remove this.
Also document __open_device() return values, remove a redundant
td->changed = 1 in __create_thin(), and insert an additional
safeguard against creating an already-existing device.
Signed-off-by: Mike Snitzer <snitzer@redhat.com> Cc: stable@kernel.org Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Mike Snitzer [Wed, 7 Mar 2012 19:09:39 +0000 (19:09 +0000)]
dm flakey: fix crash on read when corrupt_bio_byte not set
The following BUG is hit on the first read that is submitted to a dm
flakey test device while the device is "down" if the corrupt_bio_byte
feature wasn't requested when the device's table was loaded.
Example DM table that will hit this BUG:
0 2097152 flakey 8:0 2048 0 30
Signed-off-by: Milan Broz <mbroz@redhat.com> Cc: stable@kernel.org Acked-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Jesper Juhl [Wed, 7 Mar 2012 19:09:34 +0000 (19:09 +0000)]
dm ioctl: do not leak argv if target message only contains whitespace
If 'argc' is zero we jump to the 'out:' label, but this leaks the
(unused) memory that 'dm_split_args()' allocated for 'argv' if the
string being split consisted entirely of whitespace. Jump to the
'out_argv:' label instead to free up that memory.
Guenter Roeck [Wed, 7 Mar 2012 11:58:55 +0000 (03:58 -0800)]
hwmon: (zl6100) Maintain delay parameter in driver instance data
A global delay parameter has the side effect of being overwritten with 0 if a
single ZL2004 or ZL6105 is instantiated. If other chips supported by the same
driver are in the system, this will result in access errors for those chips.
To solve the problem, keep a per-instance copy of the delay parameter, and do
not change the original parameter.
Linus Torvalds [Wed, 7 Mar 2012 16:31:31 +0000 (08:31 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input updates from Dmitry Torokhov: "Just a few driver fixups,
nothing exciting."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: wacom - fix 3rd-gen Bamboo MT when 4+ fingers are in use
Input: twl4030-vibra - use proper guard for PM methods
Input: evdev - fix variable initialisation
Input: wacom - add missing LEDS_CLASS to Kconfig
Input: ALPS - fix touchpad detection when buttons are pressed
Mark Salter [Wed, 7 Mar 2012 16:19:31 +0000 (11:19 -0500)]
C6X: fix KSTK_EIP and KSTK_ESP macros
There was a latent typo in the C6X KSTK_EIP and KSTK_ESP macros which
caused a problem with a new patch which used them. The broken definitions
were of the form:
#define KSTK_FOO(tsk) (task_pt_regs(task)->foo)
Note the use of task vs tsk. This actually worked before because the
only place in the kernel which used these macros passed in a local
pointer named task.
It causes some odd regression that we have not figured out, and it's too
late in the -rc series to try to figure it out now.
As reported by Konstantin Khlebnikov, it causes consistent hangs on his
laptop (Thinkpad x220: 2x cores + HT). They can be avoided by adding
calls to "rebuild_sched_domains();" in cpuset_cpu_[in]active() for the
CPU_{ONLINE/DOWN_FAILED/DOWN_PREPARE}_FROZEN cases, but it's not at all
clear why, and it makes no sense.
Konstantin's config doesn't even have CONFIG_CPUSETS enabled, just to
make things even more interesting. So it's not the cpusets, it's just
the scheduling domains.
So until this is understood, revert.
Bisected-reported-and-tested-by: Konstantin Khlebnikov <khlebnikov@openvz.org> Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Acked-by: Ingo Molnar <mingo@elte.hu> Acked-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dave Airlie [Tue, 6 Mar 2012 10:44:40 +0000 (10:44 +0000)]
drm/radeon: deal with errors from framebuffer init path.
We've been getting occasional oops running a 32-bit kernel on a certain
system in our RHEL test hw. It appears that we fail to get sufficent ioremap
space for the framebuffer, and this leads to an oops.
This patch should fix the oops and leave a message in the logs we can
check for.
A future fix would probably to resize the console to a size that we can
ioremap.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Christian König [Wed, 7 Mar 2012 10:28:57 +0000 (11:28 +0100)]
drm/radeon: fix a semaphore deadlock on pre cayman asics
The out of order execution of semaphore commands on
pre cayman asics doesn't work correctly and can
cause deadlocks, so turn it off for now.
Signed-off-by: Christian König <deathsimple@vodafone.de> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
When a CPU is taken out of reset, either cold booted or hotplugged in,
some of its PMU registers can contain UNKNOWN values.
This patch adds a hotplug notifier to ARM core perf code so that upon
CPU restart the PMU unit is reset and becomes ready to use again.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Will Deacon [Tue, 6 Mar 2012 16:35:55 +0000 (17:35 +0100)]
ARM: 7357/1: perf: fix overflow handling for xscale2 PMUs
xscale2 PMUs indicate overflow not via the PMU control register, but by
a separate overflow FLAG register instead.
This patch fixes the xscale2 PMU code to use this register to detect
to overflow and ensures that we clear any pending overflow when
disabling a counter.
Cc: <stable@vger.kernel.org> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Will Deacon [Tue, 6 Mar 2012 16:34:50 +0000 (17:34 +0100)]
ARM: 7356/1: perf: check that we have an event in the PMU IRQ handlers
The PMU IRQ handlers in perf assume that if a counter has overflowed
then perf must be responsible. In the paranoid world of crazy hardware,
this could be false, so check that we do have a valid event before
attempting to dereference NULL in the interrupt path.
Cc: <stable@vger.kernel.org> Signed-off-by: Ming Lei <tom.leiming@gmail.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Will Deacon [Tue, 6 Mar 2012 16:34:22 +0000 (17:34 +0100)]
ARM: 7355/1: perf: clear overflow flag when disabling counter on ARMv7 PMU
When disabling a counter on an ARMv7 PMU, we should also clear the
overflow flag in case an overflow occurred whilst stopping the counter.
This prevents a spurious overflow being picked up later and leading to
either false accounting or a NULL dereference.
Cc: <stable@vger.kernel.org> Reported-by: Ming Lei <tom.leiming@gmail.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Will Deacon [Tue, 6 Mar 2012 16:33:17 +0000 (17:33 +0100)]
ARM: 7354/1: perf: limit sample_period to half max_period in non-sampling mode
On ARM, the PMU does not stop counting after an overflow and therefore
IRQ latency affects the new counter value read by the kernel. This is
significant for non-sampling runs where it is possible for the new value
to overtake the previous one, causing the delta to be out by up to
max_period events.
Commit a737823d ("ARM: 6835/1: perf: ensure overflows aren't missed due
to IRQ latency") attempted to fix this problem by allowing interrupt
handlers to pass an overflow flag to the event update function, causing
the overflow calculation to assume that the counter passed through zero
when going from prev to new. Unfortunately, this doesn't work when
overflow occurs on the perf_task_tick path because we have the flag
cleared and end up computing a large negative delta.
This patch removes the overflow flag from armpmu_event_update and
instead limits the sample_period to half of the max_period for
non-sampling profiling runs.
Cc: <stable@vger.kernel.org> Signed-off-by: Ming Lei <ming.lei@canonical.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Kailang Yang [Wed, 7 Mar 2012 07:25:20 +0000 (08:25 +0100)]
ALSA: hda/realtek - Apply the coef-setup only to ALC269VB
The coef setup in alc269_fill_coef() was designed only for ALC269VB
model, and this has some bad effects for other ALC269 variants, such
as turning off the external mic input. Apply it only to ALC269VB.
Signed-off-by: Kailang Yang <kailang@realtek.com> Cc: <stable@kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de>
1) TCP can chop up SACK'd SKBs below below the unacked send sequence and
that breaks lots of stuff. Fix from Neal Cardwell.
2) There is code in ipv6 to properly join and leave the all-routers
multicast code when the forwarding setting is changed, but once
forwarding is turned on, we don't do the join for newly registered
devices. Fix from Li Wei.
3) Netfilter's NAT module autoload in ctnetlink drops a spinlock around
a sleeping call, problem is this code path doesn't actually hold that
lock. Fix from Pablo Neira Ayuso.
4) TG3 uses the wrong interfaces to hook into the new byte queue limit
support. It uses the device level interfaces, which is fine for
single queue devices, but on more recent chips this driver supports
multiqueue so we have to use the multiqueue BQL APIs. Fix from Tom
Herbert.
5) r8169 resume fix from Francois Romieu.
6) Add some cxgb4 device IDs, from Vipul Pandya.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
IPv6: Fix not join all-router mcast group when forwarding set.
caif-hsi: Set default MTU to 4096
cxgb4vf: Add support for Chelsio's T480-CR and T440-LP-CR adapters
cxgb4: Add support for Chelsio's T480-CR and T440-LP-CR adapters
mlx4_core: remove buggy sched_queue masking
netfilter: nf_conntrack: fix early_drop with reliable event delivery
bridge: netfilter: don't call iptables on vlan packets if sysctl is off
netfilter: bridge: fix wrong pointer dereference
netfilter: ctnetlink: remove incorrect spin_[un]lock_bh on NAT module autoload
netfilter: ebtables: fix wrong name length while copying to user-space
r8169: runtime resume before shutdown.
tcp: fix tcp_shift_skb_data() to not shift SACKed data below snd_una
tg3: Fix to use multi queue BQL interfaces
Linus Torvalds [Wed, 7 Mar 2012 02:48:13 +0000 (18:48 -0800)]
x86: fix typo in recent find_vma_prev purge
It turns out that test-compiling this file on x86-64 doesn't really
help, because much of it is x86-32-specific. And so I hadn't noticed
the slightly over-eager removal of the 'r' from 'addr' variable despite
thinking I had tested it.
projects / linux-beck.git / log