Robert Jarzmik [Mon, 9 Apr 2012 11:19:08 +0000 (13:19 +0200)]
mtd: docg3 fix in-middle of blocks reads
Corner case reads do not work, and return false data and
ECC. This case is typically seen in a ubifs usage, with a
read of type:
- docg3 docg3: doc_read_oob(from=14882415, mode=1,
data=(c30eca40:12), oob=( (null):0))
This results in the following reads:
- docg3 docg3: doc_read_data_area(buf= (null), len=111)
- docg3 docg3: doc_read_data_area(buf=c30eca40, len=12)
- docg3 docg3: doc_read_data_area(buf= (null), len=389)
- docg3 docg3: doc_read_data_area(buf= (null), len=0)
- docg3 docg3: doc_read_data_area(buf= (null), len=16)
If we suppose that the pages content is :
- bytes 0 .. 111 : 0x0a
- bytes 112 .. 255 : 0x0f
Then the returned bytes will be :
- 111 times 0x0a (correct)
- 0x0a 2 times and 0x0f 10 times (incorrect, should be
0x0a,0x0f)
- 0x0f 389 times (correct)
- nothing
- correct OOB
The reason seams that the first 111 bytes read ends between
the 2 docg3 planes, and that the first following read (in
the 12 bytes sequence, read of 16 bit word) returns the byte
of the rightmost plane duplicated in high and lower byte of
the word.
Fix this behaviour by ensuring that if the previous read
ended up in-between the 2 planes, there will be a first 1
byte read to get back to the beginning of leftmost plane.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Javier Martin [Fri, 11 May 2012 10:15:41 +0000 (12:15 +0200)]
mtd: add fixup for S29NS512P NOR flash.
Spansion S29NS512P flash uses a 16bit transfer to report number
of sectors instead of two 8bit accesses as CFI specifies.
Artem: remove warning message which said that we are applying the
fixup - no need to scary the user unnecessarily.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
jffs2: allow to complete xattr integrity check on first GC scan
Unlike file data integrity the xattr data integrity was not checked
before some explicit access to the attribute was made.
This could leave in the system a number of corrupted extended attributes
which will be detected only at access time and possibly at a very late
time compared to the time the corruption actually happened.
This patch adds the ability to check for extended attribute integrity
on first GC scan pass (similar to file data integrity check). This allows
for all present attributes to be completly verified before any use of them.
In order to work correctly this patch also needs the patch allowing
JFFS2 to discriminate between recoverable and non recoverable errors
on extended attributes.
It allows JFFS2 to make the distinction between a potential transient
error (reading or writing the media) and a non recoverable error like a
bad CRC on the extended attribute data or some insconsitent parameters.
In order to make clear that the error is indeed intended to report a
corrupted attribute, a new local error code (JFFS2_XATTR_IS_CORRUPTED)
is introduced rather than returning a confusing positive EIO, which is
what led to the inappropriate "fix" last time.
This error code is never reported to user space and only checked locally
in this file.
Ivan Djelic [Mon, 30 Apr 2012 10:17:18 +0000 (12:17 +0200)]
mtd: nand: omap: add support for hardware BCH ecc
Two modes are supported: 4-bit and 8-bit error correction.
Note that 4-bit mode is only confirmed to work on OMAP3630 ES 1.x,
x >= 1. The OMAP3 GPMC hardware BCH engine computes remainder
polynomials, it does not provide automatic error location and
correction: this step is implemented using the BCH library.
This implementation only protects page data, there is no support
for protecting user-defined spare area bytes (this could be added
with few modifications); therefore, it cannot be used with YAFFS2
or other similar filesystems that depend on oob storage.
Before being stored to nand flash, hardware BCH ecc is adjusted
so that an erased page has a valid ecc; thus allowing correction of
bitflips in blank pages (also common on 4-bit devices).
BCH correction mode is selected at runtime by setting platform data
parameter 'ecc_opt' to value OMAP_ECC_BCH4_CODE_HW or
OMAP_ECC_BCH8_CODE_HW.
This code has been tested with mtd test modules, UBI and UBIFS on a
BeagleBoard revC3 (OMAP3530 ES3.0 + Micron NAND 256MiB 1,8V 16-bit).
Signed-off-by: Ivan Djelic <ivan.djelic@parrot.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Ivan Djelic [Thu, 26 Apr 2012 12:17:49 +0000 (14:17 +0200)]
ARM: OMAP3: gpmc: add BCH ecc api and modes
This patch adds a simple BCH ecc computation api, similar to the
existing Hamming ecc api. It is intended to be used by the MTD layer.
It implements the following features:
- support 4-bit and 8-bit ecc computation
- do not protect user bytes in spare area, only data area is protected
- ecc for an erased NAND page (0xFFs) is also a sequence of 0xFFs
This last feature is obtained by adding a constant polynomial to
the hardware computed ecc. It allows to correct bitflips in blank pages
and is extremely useful to support filesystems such as UBIFS, which expect
erased pages to contain only 0xFFs.
This api has been tested on an OMAP3630 board.
Artem: The OMAP maintainer Tony Lindgren gave us his blessing for merging
this patch via the MTD tree.
Signed-off-by: Ivan Djelic <ivan.djelic@parrot.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Thomas Abraham [Tue, 8 May 2012 22:34:54 +0000 (04:04 +0530)]
mtd: m25p80: Add support for Winbond W25Q80BW
Winbond W25Q80BW is a 8Mbit serial flash memory device.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Currently JFFS2 file-system maps the VFS "superblock" abstraction to the
write-buffer. Namely, it uses VFS services to synchronize the write-buffer
periodically.
The whole "superblock write-out" VFS infrastructure is served by the
'sync_supers()' kernel thread, which wakes up every 5 (by default) seconds and
writes out all dirty superblock using the '->write_super()' call-back. But the
problem with this thread is that it wastes power by waking up the system every
5 seconds no matter what. So we want to kill it completely and thus, we need to
make file-systems to stop using the '->write_super' VFS service, and then
remove it together with the kernel thread.
This patch switches the JFFS2 write-buffer management from
'->write_super()'/'->s_dirt' to a delayed work. Instead of setting the 's_dirt'
flag we just schedule a delayed work for synchronizing the write-buffer.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
We do not need to call 'jffs2_write_super()' on sync. This function
causes a GC pass to make sure the current contents is pushed out with
the data which we already have on the media.
But this is not needed on unmount and only slows sync down unnecessarily.
It is enough to just sync the write-buffer.
We do not need to call 'jffs2_write_super()' on unmount. This function
causes a GC pass to make sure the current contents is pushed out with
the data which we already have on the media.
But this is not needed on unmount and only slows unmount down unnecessarily.
It is enough to just sync the write-buffer.
Brian Norris [Wed, 2 May 2012 17:14:56 +0000 (10:14 -0700)]
mtd: nand: pass proper 'oob_required' parameter
We now have an interface for notifying the nand_ecc_ctrl functions when OOB
data must be returned to the upper layers and when it may be left untouched.
This patch fills in the 'oob_required' parameter properly from
nand_do_{read,write}_ops. When utilized properly in the lower layers, this
parameter can improve performance and/or reduce complexity for NAND HW and SW
that can simply avoid transferring the OOB data.
Signed-off-by: Brian Norris <computersforpeace@gmail.com> Reviewed-by: Shmulik Ladkani <shmulik.ladkani@gmail.com> Acked-by: Jiandong Zheng <jdzheng@broadcom.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Brian Norris [Wed, 2 May 2012 17:14:55 +0000 (10:14 -0700)]
mtd: nand: add 'oob_required' argument to NAND {read,write}_page interfaces
New NAND controllers can perform read/write via HW engines which don't expose
OOB data in their DMA mode. To reflect this, we should rework the nand_chip /
nand_ecc_ctrl interfaces that assume that drivers will always read/write OOB
data in the nand_chip.oob_poi buffer. A better interface includes a boolean
argument that explicitly tells the callee when OOB data is requested by the
calling layer (for reading/writing to/from nand_chip.oob_poi).
This patch adds the 'oob_required' parameter to each relevant {read,write}_page
interface; all 'oob_required' parameters are left unused for now. The next
patch will set the parameter properly in the nand_base.c callers, and follow-up
patches will make use of 'oob_required' in some of the callee functions.
Note that currently, there is no harm in ignoring the 'oob_required' parameter
and *always* utilizing nand_chip.oob_poi, but there can be
performance/complexity/design benefits from avoiding filling oob_poi in the
common case. I will try to implement this for some drivers which can be ported
easily.
Note: I couldn't compile-test all of these easily, as some had ARCH
dependencies.
[dwmw2: Merge later 1/0 vs. true/false cleanup] Signed-off-by: Brian Norris <computersforpeace@gmail.com> Reviewed-by: Shmulik Ladkani <shmulik.ladkani@gmail.com> Acked-by: Jiandong Zheng <jdzheng@broadcom.com> Acked-by: Mike Dunn <mikedunn@newsguy.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
John Crispin [Mon, 30 Apr 2012 17:30:47 +0000 (19:30 +0200)]
mtd: add read_byte support to plat_nand
Lantiq SoCs have a External Bus Unit (EBU) that is used to attach MTD media.
As we need to co-exist with PCI on the same bus, certain swapping settings must
be applied. Similar to the NOR map driver we need to apply a fix to make NAND
work. The easiest way is to use byte reads.
Signed-off-by: John Crispin <blogic@openwrt.org> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
John Crispin [Mon, 30 Apr 2012 17:30:46 +0000 (19:30 +0200)]
OF: MTD: make plat_nand loadable from DT
This patch sets the of_match_table field inside plat_nand's platform_driver.
We also add a struct mtd_part_parser_data pointer to make sure of_part parsing
works.
If an arch wants to support plat_nand via DT it needs to setup the
platform_nand_data and hook it into the platform_device.
Signed-off-by: John Crispin <blogic@openwrt.org> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Brian Norris [Wed, 2 May 2012 00:12:54 +0000 (17:12 -0700)]
mtd: nand: remove autoincrement 'sndcmd' code
The NAND_NO_AUTOINCR option is always set, so we will kill the option and make
"no autoincrement" the default behavior for nand_base.c. Thus, we should remove
the code which decides whether or not to send the NAND_CMD_READ0 command.
Instead, we unconditionally send the command.
Signed-off-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Brian Norris [Wed, 2 May 2012 00:12:53 +0000 (17:12 -0700)]
mtd: nandsim: remove autoincrement code
The NAND layer always has NAND_NO_AUTOINCR set, so we will never utilize the
AUTOINCR code in nandsim. We will be removing the NAND_NO_AUTOINCR option soon,
and so kill this code as well.
Signed-off-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The drivers' _read() method, absent an error, returns a non-negative integer
indicating the maximum number of bit errors that were corrected in any one
region comprising an ecc step. MTD returns -EUCLEAN if this is >=
bitflip_threshold, 0 otherwise. If bitflip_threshold is zero, the comparison is
not made since these devices lack ECC and always return zero in the non-error
case (thanks Brian)¹. Note that this is a subtle change to the driver
interface.
This and the preceding patches in this set were tested with ubi on top of the
nandsim and docg4 devices, running the ubi test io_basic from mtd-utils.
Signed-off-by: Mike Dunn <mikedunn@newsguy.com> Acked-by: Robert Jarzmik <robert.jarzmik@free.fr> Acked-by: Brian Norris <computersforpeace@gmail.com>
Ivan Djelic <ivan.djelic@parrot.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Mike Dunn [Wed, 25 Apr 2012 19:06:10 +0000 (12:06 -0700)]
mtd: nand: add sanity check of ecc strength to nand_scan_tail()
This patch adds sanity checks that ensure that drivers for controllers with
hardware ECC set the 'strength' element in struct nand_ecc_ctrl. Also stylistic
changes to the line that calculates strength for software ECC.
Signed-off-by: Mike Dunn <mikedunn@newsguy.com> Acked-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Mike Dunn [Wed, 25 Apr 2012 19:06:09 +0000 (12:06 -0700)]
mtd: nand: read_page() returns max_bitflips
The ecc.read_page() method for nand drivers is changed to return the maximum
number of bitflips that were corrected on any one region covering an ecc step,
This patch doesn't change what the nand code returns to mtd.
This v2 includes the change to the fsl_ifc_nand driver requested by Scott¹.
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Acked-by (freescale changes): Scott Wood <scottwood@freescale.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Mike Dunn [Wed, 25 Apr 2012 19:06:08 +0000 (12:06 -0700)]
mtd: bitflip_threshold added to mtd_info and sysfs
An element 'bitflip_threshold' is added to struct mtd_info, and also exposed as
a read/write variable in sysfs. This will be used to determine whether or not
mtd_read() returns -EUCLEAN or 0 (absent a hard error). If the driver leaves it
as zero, mtd will set it to a default value of ecc_strength.
This v2 adds the line that propagates bitflip_threshold from the master to the
partitions - thanks Ivan¹.
Signed-off-by: Mike Dunn <mikedunn@newsguy.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Mike Dunn [Wed, 25 Apr 2012 19:06:07 +0000 (12:06 -0700)]
mtd: expose ecc_strength through sysfs
ecc_strength element of struct mtd_info is exposed as a read-only variable in
sysfs.
Signed-off-by: Mike Dunn <mikedunn@newsguy.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Mike Dunn [Wed, 25 Apr 2012 19:06:06 +0000 (12:06 -0700)]
mtd: nand: fix incorrect ecc strength values
This fixes a couple of ecc strength values for which I earlier made conservative
guesses, but whose correct values were later determined¹ (thanks Ivan). Also
sets strength for fsl_ifc_nand, which was merged to mainline after the original
patch that set the strength for all drivers.
Signed-off-by: Mike Dunn <mikedunn@newsguy.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Mike Dunn [Wed, 25 Apr 2012 19:06:05 +0000 (12:06 -0700)]
mtd: ecc_strength is at ecc step granularity
ecc_strength element of mtd_info will be the strength of one ecc step, not of
the entire writesize, as was previously planned. This is the appropriate way
because, as was pointed out¹, bit errors in excess of the strength of one
step can cause a hard error if they all occur within the same ecc region.
Signed-off-by: Mike Dunn <mikedunn@newsguy.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
mtd: nand: Add a NAND_CMD_STATUS when using write verification
To make sure the NAND chip is properly programmed we need a status
command before each page write. When CONFIG_MTD_NAND_VERIFY_WRITE=y this
assumption is broken when writing multiple pages consecutively. This
patch fixes this.
Xi Wang [Wed, 25 Apr 2012 18:45:22 +0000 (14:45 -0400)]
jffs2: validate symlink size in jffs2_do_read_inode_internal()
`csize' is read from disk and thus needs validation. Otherwise a bogus
value 0xffffffff would turn the subsequent kmalloc(csize + 1, ...) into
kmalloc(0, ...), leading to out-of-bounds write.
This patch limits `csize' to JFFS2_MAX_NAME_LEN, which is also used
in jffs2_symlink().
Artem: we actually validate csize by checking CRC, so this 0xFFs cannot
come from empty flash region. But I guess an attacker could feed JFFS2
an image with random csize value, including 0xFFs.
Signed-off-by: Xi Wang <xi.wang@gmail.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Jonas Gorski [Thu, 19 Apr 2012 11:15:57 +0000 (13:15 +0200)]
mtd: bcm63xxpart: handle Broadcom partition order
The original Broadcom partition order has the root fs in front of the
kernel, which resulted in miscalculated partition sizes.
Detect when such an image is on the flash and also reorder the partitions
accordingly.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> Acked-by: Florian Fainelli <florian@openwrt.org> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Ivan Djelic [Tue, 17 Apr 2012 11:11:53 +0000 (13:11 +0200)]
mtd: nand: omap: fix race condition in omap_wait()
If a context switch occurs in function omap_wait() just before the
while loop is entered, then upon return from context switch the
timeout may already have elapsed: in that case, status is never
read from NAND device, and omap_wait() returns an error.
This failure has been experimentally observed during stress tests.
This patch ensures a NAND status read is always performed before
returning, as in the generic nand_wait() function.
Signed-off-by: Ivan Djelic <ivan.djelic@parrot.com> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
clk_{un}prepare is mandatory for platforms using common clock framework. Since
this driver is used by SPEAr platform, which supports common clock framework,
add clk_{un}prepare() support for it.
clk_{un}prepare is mandatory for platforms using common clock framework. Since
this driver is used by SPEAr platform, which supports common clock framework,
add clk_{un}prepare() support for it.
Randy Dunlap [Mon, 16 Apr 2012 19:50:37 +0000 (12:50 -0700)]
mtd: fix scb2_flash build when PCI is not enabled
scb2_flash.c is a PCI driver, but its build fails when CONFIG_PCI
is not enabled, so make it depend on PCI.
drivers/mtd/maps/scb2_flash.c:237:1: warning: data definition has no type or storage class
drivers/mtd/maps/scb2_flash.c:237:1: warning: type defaults to 'int' in declaration of 'module_pci_driver'
drivers/mtd/maps/scb2_flash.c:237:1: warning: parameter names (without types) in function declaration
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Daniel Drake [Tue, 10 Apr 2012 21:22:35 +0000 (22:22 +0100)]
JFFS2: Add parameter to reserve disk space for root
Add a new rp_size= parameter which creates a "reserved pool" of disk
space which can only be used by root. Other users are not permitted
to write to disk when the available space is less than the pool size.
Based on original code by Artem Bityutskiy in
https://dev.laptop.org/ticket/5317
[dwmw2: use capable(CAP_SYS_RESOURCE) not uid/gid check, fix debug prints] Signed-off-by: Daniel Drake <dsd@laptop.org> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
mtd: print out the page size and oob size after parsing out the nand
Some not-supported nand chips may pass the current parsing code,
and get the wrong page size and oob size. Sometimes, it's hard to notice
that you get the wrong values, because there is no warning or error.
So it's useful to print out the page size and oob size in the end of
the parsing function. We can check these values with the datasheet of the nand
chip as soon as possible.
Axel Lin [Tue, 3 Apr 2012 01:59:44 +0000 (09:59 +0800)]
mtd: use module_pci_driver
This patch converts the drivers in drivers/mtd/* to use module_pci_driver()
macro which makes the code smaller and a bit simpler.
Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Uwe Kleine-König [Thu, 29 Mar 2012 21:12:32 +0000 (23:12 +0200)]
mtd: mark const init data with __initconst instead of __initdata
As long as there is no other non-const variable marked __initdata in the
same compilation unit it doesn't hurt. If there were one however
compilation would fail with
error: $variablename causes a section type conflict
because a section containing const variables is marked read only and so
cannot contain non-const variables.
Use the default partition parser, cmdlinepart, provided by the plat_nand driver.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com> Acked-by: Tony Lindgren <tony@atomide.com> Acked-by: Alexander Clouter <alex@digriz.org.uk> Acked-by: Marek Vasut <marek.vasut@gmail.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Linus Torvalds [Sun, 13 May 2012 18:33:09 +0000 (11:33 -0700)]
Merge tag 'for-linus-3.4-20120513' of git://git.infradead.org/linux-mtd
Pull three MTD fixes from David Woodhouse:
- Fix a lock ordering deadlock in JFFS2
- Fix an oops in the dataflash driver, triggered by a dummy call to test
whether it has OTP functionality.
- Fix request_mem_region() failure on amsdelta NAND driver.
* tag 'for-linus-3.4-20120513' of git://git.infradead.org/linux-mtd:
mtd: ams-delta: fix request_mem_region() failure
jffs2: Fix lock acquisition order bug in gc path
mtd: fix oops in dataflash driver
Linus Torvalds [Sun, 13 May 2012 00:27:41 +0000 (17:27 -0700)]
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM: SoC fixes from Olof Johansson:
"I was hoping to be done with fixes for 3.4 but we got two branches
from subarch maintainers the last couple of days. So here is one
last(?) pull request for arm-soc containing 7 patches:
- Five of them are for shmobile dealing with SMP setup and compile
failures
- The remaining two are for regressions on the Samsung platforms"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: EXYNOS: fix ctrlbit for exynos5_clk_pdma1
ARM: EXYNOS: use s5p-timer for UniversalC210 board
ARM / mach-shmobile: Invalidate caches when booting secondary cores
ARM / mach-shmobile: sh73a0 SMP TWD boot regression fix
ARM / mach-shmobile: r8a7779 SMP TWD boot regression fix
ARM: mach-shmobile: convert ag5evm to use the generic MMC GPIO hotplug helper
ARM: mach-shmobile: convert mackerel to use the generic MMC GPIO hotplug helper
Linus Torvalds [Sun, 13 May 2012 00:24:29 +0000 (17:24 -0700)]
Merge tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux-2.6
Pull a few more GPIO bug fixes from Grant Likely:
"Oops, missed a couple. Here's an updated pull req for GPIO"
A set of PCH bug fixes, and one patch to fix up compile warnings
* tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux-2.6:
gpio/exynos: Fix compiler warnings when non-exynos machines are selected
gpio: pch9: Use proper flow type handlers
Olof Johansson [Sat, 12 May 2012 22:41:22 +0000 (15:41 -0700)]
Merge branch 'v3.4-samsung-fixes-5' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes
* 'v3.4-samsung-fixes-5' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: fix ctrlbit for exynos5_clk_pdma1
ARM: EXYNOS: use s5p-timer for UniversalC210 board
Marek Szyprowski [Fri, 11 May 2012 21:17:59 +0000 (06:17 +0900)]
ARM: EXYNOS: use s5p-timer for UniversalC210 board
Commit 069d4e743 ("ARM: EXYNOS4: Remove clock event timers using
ARM private timers") removed support for local timers and forced
to use MCT as event source. However MCT is not operating properly
on early revision of EXYNOS4 SoCs. All UniversalC210 boards are
based on it, so that commit broke support for it. This patch
provides a workaround that enables UniversalC210 boards to boot
again. s5p-timer is used as an event source, it works only for
non-SMP builds.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Olof Johansson [Sat, 12 May 2012 22:40:56 +0000 (15:40 -0700)]
Merge branch 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/renesas into fixes
By Guennadi Liakhovetski (2) and others via Rafael J. Wysocki:
"[...] urgent fixes for Renesas ARM-based platforms. Four of these
commits are fixes of regressions new in 3.4-rc and the last one is
necessary for SMP to work on those systems in general."
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/renesas:
ARM / mach-shmobile: Invalidate caches when booting secondary cores
ARM / mach-shmobile: sh73a0 SMP TWD boot regression fix
ARM / mach-shmobile: r8a7779 SMP TWD boot regression fix
ARM: mach-shmobile: convert ag5evm to use the generic MMC GPIO hotplug helper
ARM: mach-shmobile: convert mackerel to use the generic MMC GPIO hotplug helper
Magnus Damm [Wed, 9 May 2012 07:24:59 +0000 (16:24 +0900)]
ARM / mach-shmobile: Invalidate caches when booting secondary cores
Make sure L1 caches are invalidated when booting secondary
cores. Needed to boot all mach-shmobile SMP systems that
are using Cortex-A9 including sh73a0, r8a7779 and EMEV2.
Thanks to imx and tegra guys for actual code.
Signed-off-by: Magnus Damm <damm@opensource.se> Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
ARM / mach-shmobile: sh73a0 SMP TWD boot regression fix
Fix SMP TWD boot regression on sh73a0 based platforms caused by:
4200b16 ARM: shmobile: convert to twd_local_timer_register() interface
After the merge of the above commit it has been impossible to boot
sh73a0 based SoCs with SMP enabled and CONFIG_HAVE_ARM_TWD=y. The
kernel crashes at smp_init_cpus() timing which is before the console
has been initialized, so to the user this looks like a kernel lock up
without any particular error message.
This patch fixes the regression on sh73a0 by moving the TWD
registration code from smp_init_cpus() to sys_timer->init() time.
This patch removed shmobile_twd_init() which is no longer needed
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Magnus Damm <damm@opensource.se> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Magnus Damm [Thu, 10 May 2012 05:57:22 +0000 (14:57 +0900)]
ARM / mach-shmobile: r8a7779 SMP TWD boot regression fix
Fix SMP TWD boot regression on r8a7779 based platforms caused by:
4200b16 ARM: shmobile: convert to twd_local_timer_register() interface
After the merge of the above commit it has been impossible to boot
r8a7779 based SoCs with SMP enabled and CONFIG_HAVE_ARM_TWD=y. The
kernel crashes at smp_init_cpus() timing which is before the console
has been initialized, so to the user this looks like a kernel lock up
without any particular error message.
This patch fixes the regression on r8a7779 by moving the TWD
registration code from smp_init_cpus() to sys_timer->init() time.
Signed-off-by: Magnus Damm <damm@opensource.se> Acked-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
ARM: mach-shmobile: convert ag5evm to use the generic MMC GPIO hotplug helper
This also fixes the following modular mmc build failure:
arch/arm/mach-shmobile/built-in.o: In function `mackerel_sdhi0_gpio_cd':
pfc-sh7372.c:(.text+0x1138): undefined reference to `mmc_detect_change'
on this platform by eliminating the use of an inline function, which
calls into the mmc core.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Reviewed-by: Simon Horman <horms@verge.net.au> Acked-by: Magnus Damm <damm@opensource.se> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
ARM: mach-shmobile: convert mackerel to use the generic MMC GPIO hotplug helper
This also fixes the following modular mmc build failure:
arch/arm/mach-shmobile/built-in.o: In function `ag5evm_sdhi0_gpio_cd':
pfc-sh73a0.c:(.text+0x7c0): undefined reference to `mmc_detect_change'
on this platform by eliminating the use of an inline function, which
calls into the mmc core.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Tested-by: Simon Horman <horms@verge.net.au> Acked-by: Magnus Damm <damm@opensource.se> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Linus Torvalds [Sat, 12 May 2012 20:02:31 +0000 (13:02 -0700)]
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a set of minor qla and virto fixes plus one major regression
fix (oops in all legacy host drivers)."
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
[SCSI] virtio_scsi: fix TMF use-after-free
[SCSI] fix oops in all legacy host adapters caused by 6f381fa
[SCSI] qla2xxx: Update version number to 8.04.00.03-k.
[SCSI] qla2xxx: Properly check for current state after the fabric-login request.
[SCSI] qla2xxx: Proper completion to scsi-ml for scsi status task_set_full and busy.
[SCSI] qla2xxx: Block flash access from application when device is initialized for ISP82xx.
[SCSI] qla2xxx: Fix reset time out as qla2xxx not ack to reset request.
1) Since we do RCU lookups on ipv4 FIB entries, we have to test if the
entry is dead before returning it to our caller.
2) openvswitch locking and packet validation fixes from Ansis Atteka,
Jesse Gross, and Pravin B Shelar.
3) Fix PM resume locking in IGB driver, from Benjamin Poirier.
4) Fix VLAN header handling in vhost-net and macvtap, from Basil Gor.
5) Revert a bogus network namespace isolation change that was causing
regressions on S390 networking devices.
6) If bonding decides to process and handle a LACPDU frame, we
shouldn't bump the rx_dropped counter. From Jiri Bohac.
7) Fix mis-calculation of available TX space in r8169 driver when doing
TSO, which can lead to crashes and/or hung device. From Julien
Ducourthial.
8) SCTP does not validate cached routes properly in all cases, from
Nicolas Dichtel.
9) Link status interrupt needs to be handled in ks8851 driver, from
Stephen Boyd.
10) Use capable(), not cap_raised(), in connector/userns netlink code.
From Eric W. Biederman via Andrew Morton.
11) Fix pktgen OOPS on module unload, from Eric Dumazet.
12) iwlwifi under-estimates SKB truesizes, also from Eric Dumazet.
13) Cure division by zero in SFC driver, from Ben Hutchings.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (26 commits)
ks8851: Update link status during link change interrupt
macvtap: restore vlan header on user read
vhost-net: fix handle_rx buffer size
bonding: don't increase rx_dropped after processing LACPDUs
connector/userns: replace netlink uses of cap_raised() with capable()
sctp: check cached dst before using it
pktgen: fix crash at module unload
Revert "net: maintain namespace isolation between vlan and real device"
ehea: fix losing of NEQ events when one event occurred early
igb: fix rtnl race in PM resume path
ipv4: Do not use dead fib_info entries.
r8169: fix unsigned int wraparound with TSO
sfc: Fix division by zero when using one RX channel and no SR-IOV
openvswitch: Validation of IPv6 set port action uses IPv4 header
net: compare_ether_addr[_64bits]() has no ordering
cdc_ether: Ignore bogus union descriptor for RNDIS devices
bnx2x: bug fix when loading after SAN boot
e1000: Silence sparse warnings by correcting type
igb, ixgbe: netdev_tx_reset_queue incorrectly called from tx init path
openvswitch: Release rtnl_lock if ovs_vport_cmd_build_info() failed.
...
Linus Torvalds [Sat, 12 May 2012 19:56:08 +0000 (12:56 -0700)]
Merge tag 'dm-3.4-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm
Pull device-mapper fixes from Alasdair G Kergon:
"Fix a couple of serious memory leaks in device-mapper thin
provisioning and tidy its MODULE_DESCRIPTION.
Mitigate occasional reported hangs associated with multipath scsi_dh
module loading."
* tag 'dm-3.4-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm:
dm mpath: check if scsi_dh module already loaded before trying to load
dm thin: correct module description
dm thin: fix unprotected use of prepared_discards list
dm thin: reinstate missing mempool_free in cell_release_singleton
Since cpufreq has no official maintainer at the moment, I'm willing
to maintain it along some other power management core code I've been
maintaining already.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mike Snitzer [Sat, 12 May 2012 00:43:21 +0000 (01:43 +0100)]
dm mpath: check if scsi_dh module already loaded before trying to load
If the requested scsi_dh module is already loaded then skip
request_module().
Multipath table loads can hang in an unnecessary __request_module.
Reported-by: Ben Marzinski <bmarzins@redhat.com> Cc: stable@kernel.org Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Mike Snitzer [Sat, 12 May 2012 00:43:16 +0000 (01:43 +0100)]
dm thin: fix unprotected use of prepared_discards list
Fix two places in commit 104655fd4dce ("dm thin: support discards") that
didn't use pool->lock to protect against concurrent changes to the
prepared_discards list.
Without this fix, thin_endio() can race with process_discard(), leading
to concurrent list_add()s that result in the processes locking up with
an error like the following:
Mike Snitzer [Sat, 12 May 2012 00:43:12 +0000 (01:43 +0100)]
dm thin: reinstate missing mempool_free in cell_release_singleton
Fix a significant memory leak inadvertently introduced during
simplification of cell_release_singleton() in commit 6f94a4c45a6f744383f9f695dde019998db3df55 ("dm thin: fix stacked bi_next
usage").
A cell's hlist_del() must be accompanied by a mempool_free().
Use __cell_release() to do this, like before.
Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Alasdair G Kergon <agk@redhat.com>
gpio/exynos: Fix compiler warnings when non-exynos machines are selected
Fixes the following compiler warnings:
drivers/gpio/gpio-samsung.c: In function ‘samsung_gpiolib_init’:
drivers/gpio/gpio-samsung.c:2980:1: warning: label ‘err_ioremap1’ defined but not used [-Wunused-label]
drivers/gpio/gpio-samsung.c:2978:1: warning: label ‘err_ioremap2’ defined but not used [-Wunused-label]
drivers/gpio/gpio-samsung.c:2976:1: warning: label ‘err_ioremap3’ defined but not used [-Wunused-label]
drivers/gpio/gpio-samsung.c:2974:1: warning: label ‘err_ioremap4’ defined but not used [-Wunused-label]
drivers/gpio/gpio-samsung.c:2722:55: warning: unused variable ‘gpio_base4’ [-Wunused-variable]
drivers/gpio/gpio-samsung.c:455:32: warning: ‘exynos_gpio_cfg’ defined but not used [-Wunused-variable]
drivers/gpio/gpio-samsung.c:2126:33: warning: ‘exynos4_gpios_1’ defined but not used [-Wunused-variable]
drivers/gpio/gpio-samsung.c:2228:33: warning: ‘exynos4_gpios_2’ defined but not used [-Wunused-variable]
drivers/gpio/gpio-samsung.c:2373:33: warning: ‘exynos4_gpios_3’ defined but not used [-Wunused-variable]
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Thomas Gleixner [Sat, 28 Apr 2012 08:13:45 +0000 (10:13 +0200)]
gpio: pch9: Use proper flow type handlers
Jean-Francois Dagenais reported:
Configuring a gpio pin with the gpio-pch driver with
"IRQF_TRIGGER_LOW | IRQF_ONESHOT" generates an interrupt storm for
threaded ISR until the ISR thread actually gets to physically clear
the interrupt on the triggering chip!! The immediate observable
symptom is the high CPU usage for my ISR thread task and the
interrupt count in /proc/interrupts incrementing radically.
The driver is wrong in several ways:
1) Using handle_simple_irq() does not provide proper flow control
handling. In the case of oneshot threaded handlers for the
demultiplexed interrupts this results in an interrupt storm because
the simple handler does not deal with masking/unmasking. Even
without threaded oneshot handlers an interrupt storm for level type
interrupts can easily be triggered when the interrupt is disabled
and the interrupt line is activated from the device.
2) Acknowlegding the demultiplexed interrupt before calling the
handler is wrong for level type interrupts.
3) The set_type function unconditionally enables the interrupt. It's
supposed to set the type and nothing else. The unmasking is done by
the core code.
Move the acknowledge code into a separate function and add it to the
demux irqchip callbacks.
Remove the unconditional enabling from the set_type() callback and set
the proper flow handlers depending on the selected type (level/edge).
Reported-and-tested-by: Jean-Francois Dagenais <jeff.dagenais@gmail.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Linus Torvalds [Fri, 11 May 2012 23:58:14 +0000 (16:58 -0700)]
Merge branch 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
Pull another powerpc irq fix from Benjamin Herrenschmidt:
"It looks like my previous fix for the lazy irq masking problem wasn't
quite enough. There was another problem related to performance
monitor interrupts acting as NMIs leaving the flags in an incorrect
state. Here's a fix that finally seems to make perf solid again."
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/irq: Fix another case of lazy IRQ state getting out of sync
Linus Torvalds [Fri, 11 May 2012 23:49:09 +0000 (16:49 -0700)]
Merge branch '3.4-urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending
Pull target fix from Nicholas Bellinger:
"This patch removes some incorrect legacy code to free se_lun_acl
memory in the NodeACL release path that could potentially trigger an
OOPS during shutdown once dynamic -> explicit initiator NodeACL
conversion has occurred.
That said, we've been able to trigger an OOPS in v4.0 code for this
special case when the associated MappedLUNs had not also been made
explicit based on active TPG LUN layout during the conversion, so it
really makes senses to go ahead and drop this extra cruft to avoid any
possible issues here.
This ends up only effecting iscsi-target module code (it's the only
user) and is CC'ed to stable."
* '3.4-urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
target: Drop incorrect se_lun_acl release for dynamic -> explict ACL conversion
powerpc/irq: Fix another case of lazy IRQ state getting out of sync
So we have another case of paca->irq_happened getting out of
sync with the HW irq state. This can happen when a perfmon
interrupt occurs while soft disabled, as it will return to a
soft disabled but hard enabled context while leaving a stale
PACA_IRQ_HARD_DIS flag set.
This patch fixes it, and also adds a test for the condition
of those flags being out of sync in arch_local_irq_restore()
when CONFIG_TRACE_IRQFLAGS is enabled.
This helps catching those gremlins faster (and so far I
can't seem see any anymore, so that's good news).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Stephen Boyd [Thu, 10 May 2012 12:51:30 +0000 (12:51 +0000)]
ks8851: Update link status during link change interrupt
If a link change interrupt comes in we just clear the interrupt
and continue along without notifying the upper networking layers
that the link has changed. Use the mii_check_link() function to
update the link status whenever a link change interrupt occurs.
Cc: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Basil Gor [Thu, 3 May 2012 22:55:24 +0000 (22:55 +0000)]
macvtap: restore vlan header on user read
Ethernet vlan header is not on the packet and kept in the skb->vlan_tci
when it comes from lower dev. This patch inserts vlan header in user
buffer during skb copy on user read.
Signed-off-by: Basil Gor <basil.gor@gmail.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / linux-beck.git / log