Feifei Xu [Wed, 1 Jun 2016 11:18:30 +0000 (19:18 +0800)]
Btrfs: self-tests: Fix extent buffer bitmap test fail on BE system
In __test_eb_bitmaps(), we write random data to a bitmap. Then copy
the bitmap to another bitmap that resides inside an extent buffer.
Later we verify the values of corresponding bits in the bitmap and the
bitmap inside the extent buffer. However, extent_buffer_test_bit()
reads in byte granularity while test_bit() reads in unsigned long
granularity. Hence we end up comparing wrong bits on big-endian
systems such as ppc64. This commit fixes the issue by reading the
bitmap in byte granularity.
Reviewed-by: Josef Bacik <jbacik@fb.com> Reviewed-by: Chandan Rajendra <chandan@linux.vnet.ibm.com> Signed-off-by: Feifei Xu <xufeifei@linux.vnet.ibm.com> Signed-off-by: David Sterba <dsterba@suse.com>
Feifei Xu [Wed, 1 Jun 2016 11:18:26 +0000 (19:18 +0800)]
Btrfs: self-tests: Execute page straddling test only when nodesize < PAGE_SIZE
On ppc64, PAGE_SIZE is 64k which is same as BTRFS_MAX_METADATA_BLOCKSIZE.
In such a scenario, we will never be able to have an extent buffer
containing more than one page. Hence in such cases this commit does not
execute the page straddling tests.
Reviewed-by: Josef Bacik <jbacik@fb.com> Signed-off-by: Feifei Xu <xufeifei@linux.vnet.ibm.com> Signed-off-by: Chandan Rajendra <chandan@linux.vnet.ibm.com> Signed-off-by: David Sterba <dsterba@suse.com>
Feifei Xu [Wed, 1 Jun 2016 11:18:25 +0000 (19:18 +0800)]
Btrfs: self-tests: Support non-4k page size
self-tests code assumes 4k as the sectorsize and nodesize. This commit
fix hardcoded 4K. Enables the self-tests code to be executed on non-4k
page sized systems (e.g. ppc64).
Reviewed-by: Josef Bacik <jbacik@fb.com> Signed-off-by: Feifei Xu <xufeifei@linux.vnet.ibm.com> Signed-off-by: Chandan Rajendra <chandan@linux.vnet.ibm.com> Signed-off-by: David Sterba <dsterba@suse.com>
Feifei Xu [Wed, 1 Jun 2016 11:18:23 +0000 (19:18 +0800)]
Btrfs: test_check_exists: Fix infinite loop when searching for free space entries
On a ppc64 machine using 64K as the block size, assume that the RB
tree at btrfs_free_space_ctl->free_space_offset contains following
two entries:
1. A bitmap entry having an offset value of 0 and having the bits
corresponding to the address range [128M+512K, 128M+768K] set.
2. An extent entry corresponding to the address range
[128M-256K, 128M-128K]
In such a scenario, test_check_exists() invoked for checking the
existence of address range [128M+768K, 256M] can lead to an
infinite loop as explained below:
- Checking for the extent entry fails.
- Checking for a bitmap entry results in the free space info in
range [128M+512K, 128M+768K] beng returned.
- rb_prev(info) returns NULL because the bitmap entry starting from
offset 0 comes first in the RB tree.
- current_node = bitmap node.
- while (current_node)
tmp = rb_next(bitmap_node);/*tmp is extent based free space entry*/
Since extent based free space entry's last address is smaller
than the address being searched for (i.e. 128M+768K) we
incorrectly again obtain the extent node as the "next right node"
of the RB tree and thus end up looping infinitely.
This patch fixes the issue by checking the "tmp" variable which point
to the most recently searched free space node.
Reviewed-by: Josef Bacik <jbacik@fb.com> Reviewed-by: Chandan Rajendra <chandan@linux.vnet.ibm.com> Signed-off-by: Feifei Xu <xufeifei@linux.vnet.ibm.com> Signed-off-by: David Sterba <dsterba@suse.com>
Chris Mason [Mon, 16 May 2016 16:21:01 +0000 (09:21 -0700)]
Btrfs: fix handling of faults from btrfs_copy_from_user
When btrfs_copy_from_user isn't able to copy all of the pages, we need
to adjust our accounting to reflect the work that was actually done.
Commit 2e78c927d79 changed around the decisions a little and we ended up
skipping the accounting adjustments some of the time. This commit makes
sure that when we don't copy anything at all, we still hop into
the adjustments, and switches to release_bytes instead of write_bytes,
since write_bytes isn't aligned.
The accounting errors led to warnings during btrfs_destroy_inode:
ret = pthread_create(&tid, NULL, dontneed, buf);
if (ret) {
fprintf(stderr, "error %d from pthread_create\n", ret);
exit(1);
}
ret = pthread_detach(tid);
if (ret) {
fprintf(stderr, "pthread detach failed %d\n", ret);
exit(1);
}
while (1) {
fd = open(filename, O_RDWR | O_CREAT, 0600);
if (fd < 0) {
perror("open");
exit(1);
}
for (i = 0; i < ROUNDS; i++) {
int this_write = BUFSIZE;
offset = rand() % MAXSIZE;
ret = pwrite(fd, buf, this_write, offset);
if (ret < 0) {
perror("pwrite");
exit(1);
} else if (ret != this_write) {
fprintf(stderr, "short write to %s offset %lu ret %d\n",
filename, offset, ret);
exit(1);
}
if (i == ROUNDS - 1) {
ret = sync_file_range(fd, offset, 4096,
SYNC_FILE_RANGE_WRITE);
if (ret < 0) {
perror("sync_file_range");
exit(1);
}
}
}
ret = ftruncate(fd, 0);
if (ret < 0) {
perror("ftruncate");
exit(1);
}
ret = close(fd);
if (ret) {
perror("close");
exit(1);
}
ret = unlink(filename);
if (ret) {
perror("unlink");
exit(1);
}
}
return 0;
}
Signed-off-by: Chris Mason <clm@fb.com> Reported-by: Dave Jones <dsj@fb.com> Fixes: 2e78c927d79333f299a8ac81c2fd2952caeef335
cc: stable@vger.kernel.org # v4.6 Signed-off-by: Chris Mason <clm@fb.com>
Zhao Lei [Tue, 17 May 2016 09:37:38 +0000 (17:37 +0800)]
btrfs: scrub: Set bbio to NULL before calling btrfs_map_block
We usually call btrfs_put_bbio() when btrfs_map_block() failed,
btrfs_put_bbio() works right whether bbio is a valid value, or NULL.
But there is a exception, in some case, btrfs_map_block() will return
fail without touching *bbio(keeping its original value), and if bbio
was not initialized yet, invalid memory accessing will happened.
Above case is in scrub_missing_raid56_pages(), and similar case in
scrub_raid56_parity().
Signed-off-by: Zhao Lei <zhaolei@cn.fujitsu.com> Signed-off-by: David Sterba <dsterba@suse.com>
Liu Bo [Sat, 14 May 2016 00:06:59 +0000 (17:06 -0700)]
Btrfs: free sys_array eb as soon as possible
While reading sys_chunk_array in superblock, btrfs creates a temporary
extent buffer. Since we don't use it after finishing reading
sys_chunk_array, we don't need to keep it in memory.
Signed-off-by: Liu Bo <bo.li.liu@oracle.com> Signed-off-by: David Sterba <dsterba@suse.com>
Filipe Manana [Thu, 12 May 2016 12:53:36 +0000 (13:53 +0100)]
Btrfs: add semaphore to synchronize direct IO writes with fsync
Due to the optimization of lockless direct IO writes (the inode's i_mutex
is not held) introduced in commit 38851cc19adb ("Btrfs: implement unlocked
dio write"), we started having races between such writes with concurrent
fsync operations that use the fast fsync path. These races were addressed
in the patches titled "Btrfs: fix race between fsync and lockless direct
IO writes" and "Btrfs: fix race between fsync and direct IO writes for
prealloc extents". The races happened because the direct IO path, like
every other write path, does create extent maps followed by the
corresponding ordered extents while the fast fsync path collected first
ordered extents and then it collected extent maps. This made it possible
to log file extent items (based on the collected extent maps) without
waiting for the corresponding ordered extents to complete (get their IO
done). The two fixes mentioned before added a solution that consists of
making the direct IO path create first the ordered extents and then the
extent maps, while the fsync path attempts to collect any new ordered
extents once it collects the extent maps. This was simple and did not
require adding any synchonization primitive to any data structure (struct
btrfs_inode for example) but it makes things more fragile for future
development endeavours and adds an exceptional approach compared to the
other write paths.
This change adds a read-write semaphore to the btrfs inode structure and
makes the direct IO path create the extent maps and the ordered extents
while holding read access on that semaphore, while the fast fsync path
collects extent maps and ordered extents while holding write access on
that semaphore. The logic for direct IO write path is encapsulated in a
new helper function that is used both for cow and nocow direct IO writes.
Signed-off-by: Filipe Manana <fdmanana@suse.com> Reviewed-by: Josef Bacik <jbacik@fb.com>
Filipe Manana [Mon, 9 May 2016 12:15:41 +0000 (13:15 +0100)]
Btrfs: fix race between block group relocation and nocow writes
Relocation of a block group waits for all existing tasks flushing
dellaloc, starting direct IO writes and any ordered extents before
starting the relocation process. However for direct IO writes that end
up doing nocow (inode either has the flag nodatacow set or the write is
against a prealloc extent) we have a short time window that allows for a
race that makes relocation proceed without waiting for the direct IO
write to complete first, resulting in data loss after the relocation
finishes. This is illustrated by the following diagram:
CPU 1 CPU 2
btrfs_relocate_block_group(bg X)
direct IO write starts against
an extent in block group X
using nocow mode (inode has the
nodatacow flag or the write is
for a prealloc extent)
find_next_extent()
--> returns extent that the DIO
write is going to write to
relocate_data_extent()
relocate_file_extent_cluster()
--> reads the extent from disk into
pages belonging to the relocation
inode and dirties them
--> creates DIO ordered extent
btrfs_submit_direct()
--> submits bio against a location
on disk obtained from an extent
map before the relocation started
btrfs_wait_ordered_range()
--> writes all the pages read before
to disk (belonging to the
relocation inode)
relocation finishes
bio completes and wrote new data
to the old location of the block
group
So fix this by tracking the number of nocow writers for a block group and
make sure relocation waits for that number to go down to 0 before starting
to move the extents.
The same race can also happen with buffered writes in nocow mode since the
patch I recently made titled "Btrfs: don't do unnecessary delalloc flushes
when relocating", because we are no longer flushing all delalloc which
served as a synchonization mechanism (due to page locking) and ensured
the ordered extents for nocow buffered writes were created before we
called btrfs_wait_ordered_roots(). The race with direct IO writes in nocow
mode existed before that patch (no pages are locked or used during direct
IO) and that fixed only races with direct IO writes that do cow.
Signed-off-by: Filipe Manana <fdmanana@suse.com> Reviewed-by: Josef Bacik <jbacik@fb.com>
Filipe Manana [Mon, 9 May 2016 12:15:27 +0000 (13:15 +0100)]
Btrfs: fix race between fsync and direct IO writes for prealloc extents
When we do a direct IO write against a preallocated extent (fallocate)
that does not go beyond the i_size of the inode, we do the write operation
without holding the inode's i_mutex (an optimization that landed in
commit 38851cc19adb ("Btrfs: implement unlocked dio write")). This allows
for a very tiny time window where a race can happen with a concurrent
fsync using the fast code path, as the direct IO write path creates first
a new extent map (no longer flagged as a prealloc extent) and then it
creates the ordered extent, while the fast fsync path first collects
ordered extents and then it collects extent maps. This allows for the
possibility of the fast fsync path to collect the new extent map without
collecting the new ordered extent, and therefore logging an extent item
based on the extent map without waiting for the ordered extent to be
created and complete. This can result in a situation where after a log
replay we end up with an extent not marked anymore as prealloc but it was
only partially written (or not written at all), exposing random, stale or
garbage data corresponding to the unwritten pages and without any
checksums in the csum tree covering the extent's range.
This is an extension of what was done in commit de0ee0edb21f ("Btrfs: fix
race between fsync and lockless direct IO writes").
So fix this by creating first the ordered extent and then the extent
map, so that this way if the fast fsync patch collects the new extent
map it also collects the corresponding ordered extent.
Signed-off-by: Filipe Manana <fdmanana@suse.com> Reviewed-by: Josef Bacik <jbacik@fb.com>
Filipe Manana [Thu, 5 May 2016 09:26:26 +0000 (10:26 +0100)]
Btrfs: fix number of transaction units for renames with whiteout
When we do a rename with the whiteout flag, we need to create the whiteout
inode, which in the worst case requires 5 transaction units (1 inode item,
1 inode ref, 2 dir items and 1 xattr if selinux is enabled). So bump the
number of transaction units from 11 to 16 if the whiteout flag is set.
Filipe Manana [Thu, 5 May 2016 01:08:56 +0000 (02:08 +0100)]
Btrfs: pin logs earlier when doing a rename exchange operation
The btrfs_rename_exchange() started as a copy-paste from btrfs_rename(),
which had a race fixed by my previous patch titled "Btrfs: pin log earlier
when renaming", and so it suffers from the same problem.
We pin the logs of the affected roots after we insert the new inode
references, leaving a time window where concurrent tasks logging the
inodes can end up logging both the new and old references, resulting
in log trees that when replayed can turn the metadata into inconsistent
states. This behaviour was added to btrfs_rename() in 2009 without any
explanation about why not pinning the logs earlier, just leaving a
comment about the posibility for the race. As of today it's perfectly
safe and sane to pin the logs before we start doing any of the steps
involved in the rename operation.
Filipe Manana [Thu, 5 May 2016 01:02:27 +0000 (02:02 +0100)]
Btrfs: unpin logs if rename exchange operation fails
If rename exchange operations fail at some point after we pinned any of
the logs, we end up aborting the current transaction but never unpin the
logs, which leaves concurrent tasks that are trying to sync the logs (as
part of an fsync request from user space) blocked forever and preventing
the filesystem from being unmountable.
Filipe Manana [Thu, 5 May 2016 00:41:57 +0000 (01:41 +0100)]
Btrfs: fix inode leak on failure to setup whiteout inode in rename
If we failed to fully setup the whiteout inode during a rename operation
with the whiteout flag, we ended up leaking the inode, not decrementing
its link count nor removing all its items from the fs/subvol tree.
Dan Fuhry [Thu, 17 Mar 2016 14:23:38 +0000 (15:23 +0100)]
btrfs: add support for RENAME_EXCHANGE and RENAME_WHITEOUT
Two new flags, RENAME_EXCHANGE and RENAME_WHITEOUT, provide for new
behavior in the renameat2() syscall. This behavior is primarily used by
overlayfs. This patch adds support for these flags to btrfs, enabling it to
be used as a fully functional upper layer for overlayfs.
RENAME_EXCHANGE support was written by Davide Italiano originally
submitted on 2 April 2015.
Signed-off-by: Davide Italiano <dccitaliano@gmail.com> Signed-off-by: Dan Fuhry <dfuhry@datto.com>
[ remove unlikely ] Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Filipe Manana <fdmanana@suse.com>
Filipe Manana [Fri, 29 Apr 2016 12:14:42 +0000 (13:14 +0100)]
Btrfs: pin log earlier when renaming
We were pinning the log right after the first step in the rename operation
(inserting inode ref for the new name in the destination directory)
instead of doing it before. This behaviour was introduced in 2009 for some
reason that was not mentioned neither on the changelog nor any comment,
with the drawback of a small time window where concurrent log writers can
end up logging the new inode reference for the inode we are renaming while
the rename operation is in progress (so that we can end up with a log
containing both the new and old references). As of today there's no reason
to not pin the log before that first step anymore, so just fix this.
Filipe Manana [Fri, 29 Apr 2016 10:34:22 +0000 (11:34 +0100)]
Btrfs: unpin log if rename operation fails
If rename operations fail at some point after we pinned the log, we end
up aborting the current transaction but never unpin the log, which leaves
concurrent tasks that are trying to sync the log (as part of an fsync
request from user space) blocked forever and preventing the filesystem
from being unmountable.
Filipe Manana [Tue, 26 Apr 2016 14:39:32 +0000 (15:39 +0100)]
Btrfs: don't do unnecessary delalloc flushes when relocating
Before we start the actual relocation process of a block group, we do
calls to flush delalloc of all inodes and then wait for ordered extents
to complete. However we do these flush calls just to make sure we don't
race with concurrent tasks that have actually already started to run
delalloc and have allocated an extent from the block group we want to
relocate, right before we set it to readonly mode, but have not yet
created the respective ordered extents. The flush calls make us wait
for such concurrent tasks because they end up calling
filemap_fdatawrite_range() (through btrfs_start_delalloc_roots() ->
__start_delalloc_inodes() -> btrfs_alloc_delalloc_work() ->
btrfs_run_delalloc_work()) which ends up serializing us with those tasks
due to attempts to lock the same pages (and the delalloc flush procedure
calls the allocator and creates the ordered extents before unlocking the
pages).
These flushing calls not only make us waste time (cpu, IO) but also reduce
the chances of writing larger extents (applications might be writing to
contiguous ranges and we flush before they finish dirtying the whole
ranges).
So make sure we don't flush delalloc and just wait for concurrent tasks
that have already started flushing delalloc and have allocated an extent
from the block group we are about to relocate.
This change also ends up fixing a race with direct IO writes that makes
relocation not wait for direct IO ordered extents. This race is
illustrated by the following diagram:
CPU 1 CPU 2
btrfs_relocate_block_group(bg X)
starts direct IO write,
target inode currently has no
ordered extents ongoing nor
dirty pages (delalloc regions),
therefore the root for our inode
is not in the list
fs_info->ordered_roots
btrfs_direct_IO()
__blockdev_direct_IO()
btrfs_get_blocks_direct()
btrfs_lock_extent_direct()
locks range in the io tree
btrfs_new_extent_direct()
btrfs_reserve_extent()
--> extent allocated
from bg X
btrfs_inc_block_group_ro(bg X)
btrfs_start_delalloc_roots()
__start_delalloc_inodes()
--> does nothing, no dealloc ranges
in the inode's io tree so the
inode's root is not in the list
fs_info->delalloc_roots
btrfs_wait_ordered_roots()
--> does not find the inode's root in the
list fs_info->ordered_roots
--> ends up not waiting for the direct IO
write started by the task at CPU 2
iterates the extent tree, using its
commit root and moves extents into new
locations
btrfs_add_ordered_extent_dio()
--> now a ordered extent is
created and added to the
list root->ordered_extents
and the root added to the
list fs_info->ordered_roots
--> this is too late and the
task at CPU 1 already
started the relocation
btrfs_commit_transaction()
btrfs_finish_ordered_io()
btrfs_alloc_reserved_file_extent()
--> adds delayed data reference
for the extent allocated
from bg X
prepare_to_relocate()
btrfs_commit_transaction()
--> delayed refs are run, so an extent
item for the allocated extent from
bg X is added to extent tree
--> commit roots are switched, so the
next scan in the extent tree will
see the extent item
sees the extent in the extent tree
When this happens the relocation produces the following warning when it
finishes:
This is because at the end of the first stage, in relocate_block_group(),
we commit the current transaction, which makes delayed refs run, the
commit roots are switched and so the second stage will find the extent
item that the ordered extent added to the delayed refs. But this extent
was not moved (ordered extent completed after first stage finished), so
at the end of the relocation our block group item still has a positive
used bytes counter, triggering a warning at the end of
btrfs_relocate_block_group(). Later on when trying to read the extent
contents from disk we hit a BUG_ON() due to the inability to map a block
with a logical address that belongs to the block group we relocated and
is no longer valid, resulting in the following trace:
Filipe Manana [Tue, 26 Apr 2016 14:36:38 +0000 (15:36 +0100)]
Btrfs: don't wait for unrelated IO to finish before relocation
Before the relocation process of a block group starts, it sets the block
group to readonly mode, then flushes all delalloc writes and then finally
it waits for all ordered extents to complete. This last step includes
waiting for ordered extents destinated at extents allocated in other block
groups, making us waste unecessary time.
So improve this by waiting only for ordered extents that fall into the
block group's range.
Signed-off-by: Filipe Manana <fdmanana@suse.com> Reviewed-by: Josef Bacik <jbacik@fb.com> Reviewed-by: Liu Bo <bo.li.liu@oracle.com>
Filipe Manana [Mon, 25 Apr 2016 03:45:02 +0000 (04:45 +0100)]
Btrfs: fix empty symlink after creating symlink and fsync parent dir
If we create a symlink, fsync its parent directory, crash/power fail and
mount the filesystem, we end up with an empty symlink, which not only is
useless it's also not allowed in linux (the man page symlink(2) is well
explicit about that). So we just need to make sure to fully log an inode
if it's a symlink, to ensure its inline extent gets logged, ensuring the
same behaviour as ext3, ext4, xfs, reiserfs, f2fs, nilfs2, etc.
Filipe Manana [Wed, 6 Apr 2016 16:11:56 +0000 (17:11 +0100)]
Btrfs: fix for incorrect directory entries after fsync log replay
If we move a directory to a new parent and later log that parent and don't
explicitly log the old parent, when we replay the log we can end up with
entries for the moved directory in both the old and new parent directories.
Besides being ilegal to have directories with multiple hard links in linux,
it also resulted in the leaving the inode item with a link count of 1.
A similar issue also happens if we move a regular file - after the log tree
is replayed the file has a link in both the old and new parent directories,
when it should be only at the new directory.
Sample reproducer:
$ mkfs.btrfs -f /dev/sdc
$ mount /dev/sdc /mnt
$ mkdir /mnt/x
$ mkdir /mnt/y
$ touch /mnt/x/foo
$ mkdir /mnt/y/z
$ sync
$ ln /mnt/x/foo /mnt/x/bar
$ mv /mnt/y/z /mnt/x/z
< power fail >
$ mount /dev/sdc /mnt
$ ls -1Ri /mnt
/mnt:
257 x
258 y
/mnt/x:
259 bar
259 foo
260 z
/mnt/x/z:
/mnt/y:
260 z
/mnt/y/z:
$ umount /dev/sdc
$ btrfs check /dev/sdc
Checking filesystem on /dev/sdc
UUID: a67e2c4a-a4b4-4fdc-b015-9d9af1e344be
checking extents
checking free space cache
checking fs roots
root 5 inode 260 errors 2000, link count wrong
unresolved ref dir 257 index 4 namelen 1 name z filetype 2 errors 0
unresolved ref dir 258 index 2 namelen 1 name z filetype 2 errors 0
(...)
Attempting to remove the directory becomes impossible:
$ mount /dev/sdc /mnt
$ rmdir /mnt/y/z
$ ls -lh /mnt/y
ls: cannot access /mnt/y/z: No such file or directory
total 0
d????????? ? ? ? ? ? z
$ rmdir /mnt/x/z
rmdir: failed to remove ‘/mnt/x/z’: Stale file handle
$ ls -lh /mnt/x
ls: cannot access /mnt/x/z: Stale file handle
total 0
-rw-r--r-- 2 root root 0 Apr 6 18:06 bar
-rw-r--r-- 2 root root 0 Apr 6 18:06 foo
d????????? ? ? ? ? ? z
So make sure that on rename we set the last_unlink_trans value for our
inode, even if it's a directory, to the value of the current transaction's
ID and that if the new parent directory is logged that we fallback to a
transaction commit.
A test case for fstests is being submitted as well.
David Sterba [Thu, 12 May 2016 09:05:03 +0000 (11:05 +0200)]
btrfs: build fixup for qgroup_account_snapshot
The macro btrfs_std_error got renamed to btrfs_handle_fs_error in an
independent branch for the same merge target (4.7). To make the code
compilable for bisectability reasons, add a temporary stub.
Qu Wenruo [Wed, 11 May 2016 19:53:52 +0000 (12:53 -0700)]
btrfs: qgroup: Fix qgroup accounting when creating snapshot
Current btrfs qgroup design implies a requirement that after calling
btrfs_qgroup_account_extents() there must be a commit root switch.
Normally this is OK, as btrfs_qgroup_accounting_extents() is only called
inside btrfs_commit_transaction() just be commit_cowonly_roots().
However there is a exception at create_pending_snapshot(), which will
call btrfs_qgroup_account_extents() but no any commit root switch.
In case of creating a snapshot whose parent root is itself (create a
snapshot of fs tree), it will corrupt qgroup by the following trace:
(skipped unrelated data)
======
btrfs_qgroup_account_extent: bytenr = 29786112, num_bytes = 16384, nr_old_roots = 0, nr_new_roots = 1
qgroup_update_counters: qgid = 5, cur_old_count = 0, cur_new_count = 1, rfer = 0, excl = 0
qgroup_update_counters: qgid = 5, cur_old_count = 0, cur_new_count = 1, rfer = 16384, excl = 16384
btrfs_qgroup_account_extent: bytenr = 29786112, num_bytes = 16384, nr_old_roots = 0, nr_new_roots = 0
======
The problem here is in first qgroup_account_extent(), the
nr_new_roots of the extent is 1, which means its reference got
increased, and qgroup increased its rfer and excl.
But at second qgroup_account_extent(), its reference got decreased, but
between these two qgroup_account_extent(), there is no switch roots.
This leads to the same nr_old_roots, and this extent just got ignored by
qgroup, which means this extent is wrongly accounted.
Fix it by call commit_cowonly_roots() after qgroup_account_extent() in
create_pending_snapshot(), with needed preparation.
Mark: I added a check at the top of qgroup_account_snapshot() to skip this
code if qgroups are turned off. xfstest btrfs/122 exposes this problem.
Signed-off-by: Qu Wenruo <quwenruo@cn.fujitsu.com> Reviewed-by: Josef Bacik <jbacik@fb.com> Signed-off-by: Mark Fasheh <mfasheh@suse.de> Signed-off-by: David Sterba <dsterba@suse.com>
David Sterba [Wed, 27 Apr 2016 00:41:17 +0000 (02:41 +0200)]
btrfs: make find_workspace always succeed
With just one preallocated workspace we can guarantee forward progress
even if there's no memory available for new workspaces. The cost is more
waiting but we also get rid of several error paths.
On average, there will be several idle workspaces, so the waiting
penalty won't be so bad.
In the worst case, all cpus will compete for one workspace until there's
some memory. Attempts to allocate a new one are done each time the
waiters are woken up.
David Sterba [Wed, 27 Apr 2016 00:55:15 +0000 (02:55 +0200)]
btrfs: preallocate compression workspaces
Preallocate one workspace for each compression type so we can guarantee
forward progress in the worst case. A failure cannot be a hard error as
we might not use compression at all on the filesystem. If we can't
allocate the workspaces later when need them, it might actually
deadlock, but in such situation the system has effectively not enough
memory to operate properly.
David Sterba [Mon, 9 May 2016 09:32:39 +0000 (11:32 +0200)]
btrfs: switch to common message helpers in open_ctree, adjust messages
Currently we lack the identification of the filesystem in most if not
all mount messages, done via printk/pr_* functions. We can use the
btrfs_* helpers in open_ctree, as the fs_info <-> sb link is established
at the beginning of the function.
The messages have been updated at the same time to be more consistent:
* dropped sb->s_id, as it's not available via btrfs_*
* added %d for return code where appropriate
* wording changed
* %Lx replaced by %llx
Adam Borowski [Sun, 8 May 2016 13:08:00 +0000 (15:08 +0200)]
btrfs: fix int32 overflow in shrink_delalloc().
UBSAN: Undefined behaviour in fs/btrfs/extent-tree.c:4623:21
signed integer overflow:
10808 * 262144 cannot be represented in type 'int [8]'
If 8192<=items<16384, we request a writeback of an insane number of pages
which is benign (everything will be written). But if items>=16384, the
space reservation won't be enough.
Signed-off-by: Adam Borowski <kilobyte@angband.pl> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
Linus Torvalds [Sat, 7 May 2016 17:50:48 +0000 (10:50 -0700)]
Merge tag 'staging-4.6-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull IIO driver fixes from Grek KH:
"It's really just IIO drivers here, some small fixes that resolve some
'crash on boot' errors that have shown up in the -rc series, and other
bugfixes that are required.
All have been in linux-next with no reported problems"
* tag 'staging-4.6-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
iio: imu: mpu6050: Fix name/chip_id when using ACPI
iio: imu: mpu6050: fix possible NULL dereferences
iio:adc:at91-sama5d2: Repair crash on module removal
iio: ak8975: fix maybe-uninitialized warning
iio: ak8975: Fix NULL pointer exception on early interrupt
Linus Torvalds [Sat, 7 May 2016 17:47:03 +0000 (10:47 -0700)]
Merge tag 'usb-4.6-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some last-remaining fixes for USB drivers to resolve issues
that have shown up in testing. And two new device ids as well.
All of these have been in linux-next with no reported issues"
* tag 'usb-4.6-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
Revert "USB / PM: Allow USB devices to remain runtime-suspended when sleeping"
usb: musb: jz4740: fix error check of usb_get_phy()
Revert "usb: musb: musb_host: Enable HCD_BH flag to handle urb return in bottom half"
usb: musb: gadget: nuke endpoint before setting its descriptor to NULL
USB: serial: cp210x: add Straizona Focusers device ids
USB: serial: cp210x: add ID for Link ECU
Linus Torvalds [Sat, 7 May 2016 15:27:35 +0000 (08:27 -0700)]
Merge branch 'fixes' of git://git.armlinux.org.uk/~rmk/linux-arm
Pull ARM fixes from Russell King:
"These are a number of updates to fix a few problems found in the ARM
nommu code over the last couple of years, caused mostly by changes on
the mmu side"
* 'fixes' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 8573/1: domain: move {set,get}_domain under config guard
ARM: 8572/1: nommu: change memory reserve for the vectors
ARM: 8571/1: nommu: fix PMSAv7 setup
Linus Torvalds [Sat, 7 May 2016 15:17:45 +0000 (08:17 -0700)]
Merge tag 'media/v4.6-5' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
- deadlock fixes on driver probe at exynos4-is and s43-camif drivers
- a build breakage if media controller is enabled and USB or PCI is
built as module.
* tag 'media/v4.6-5' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] media-device: fix builds when USB or PCI is compiled as module
[media] media: s3c-camif: fix deadlock on driver probe()
[media] media: exynos4-is: fix deadlock on driver probe
Linus Torvalds [Fri, 6 May 2016 20:08:35 +0000 (13:08 -0700)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-block
Pull writeback fix from Jens Axboe:
"Just a single fix for domain aware writeback, fixing a regression that
can cause balance_dirty_pages() to keep looping while not getting any
work done"
* 'for-linus' of git://git.kernel.dk/linux-block:
writeback: Fix performance regression in wb_over_bg_thresh()
Linus Torvalds [Fri, 6 May 2016 19:59:27 +0000 (12:59 -0700)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"This contains two fixes: a boot fix for older SGI/UV systems, and an
APIC calibration fix"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/tsc: Read all ratio bits from MSR_PLATFORM_INFO
x86/platform/UV: Bring back the call to map_low_mmrs in uv_system_init
Linus Torvalds [Fri, 6 May 2016 18:58:45 +0000 (11:58 -0700)]
Merge tag 'pm+acpi-4.6-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI fixes from Rafael Wysocki:
"Fixes for problems introduced or discovered recently (intel_pstate,
sti-cpufreq, ARM64 cpuidle, Operating Performance Points framework,
generic device properties framework) and one fix for a hotplug-related
deadlock in ACPICA that's been there forever, but is nasty enough.
Specifics:
- Fix for a recent regression in the intel_pstate driver causing it
to fail to restore the HWP (HW-managed P-states) configuration of
the boot CPU after suspend-to-RAM (Rafael Wysocki).
- Fix for two recent regressions in the intel_pstate driver, one that
can trigger a divide by zero if the driver is accessed via sysfs
before it manages to take the first sample and one causing it to
fail to update a structure field used in a trace point, so the
information coming from it is less useful (Rafael Wysocki).
- Fix for a problem in the sti-cpufreq driver introduced during the
4.5 cycle that causes it to break CPU PM in multi-platform kernels
by registering cpufreq-dt (which subsequently doesn't work)
unconditionally and preventing the driver that would actually work
from registering (Sudeep Holla).
- Stable-candidate fix for an ARM64 cpuidle issue causing idle state
usage counters to be incorrectly updated for idle states that were
not entered due to errors (James Morse).
- Fix for a recently introduced issue in the OPP (Operating
Performance Points) framework causing it to print bogus error
messages for missing optional regulators (Viresh Kumar).
- Fix for a recently introduced issue in the generic device
properties framework that may cause it to attempt to dereferece and
invalid pointer in some cases (Heikki Krogerus).
- Fix for a deadlock in the ACPICA core that may be triggered by
device (eg Thunderbolt) hotplug (Prarit Bhargava)"
* tag 'pm+acpi-4.6-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM / OPP: Remove useless check
ACPICA: Dispatcher: Update thread ID for recursive method calls
intel_pstate: Fix intel_pstate_get()
cpufreq: intel_pstate: Fix HWP on boot CPU after system resume
cpufreq: st: enable selective initialization based on the platform
ARM: cpuidle: Pass on arm_cpuidle_suspend()'s return value
device property: Avoid potential dereferences of invalid pointers
Linus Torvalds [Fri, 6 May 2016 18:53:27 +0000 (11:53 -0700)]
Merge branch 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fix from Ingo Molnar:
"This contains a single fix that fixes a nohz tick stopping bug when
mixed-poliocy SCHED_FIFO and SCHED_RR tasks are present on a runqueue"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
nohz/full, sched/rt: Fix missed tick-reenabling bug in sched_can_stop_tick()
Linus Torvalds [Fri, 6 May 2016 18:40:24 +0000 (11:40 -0700)]
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"This tree contains two fixes: new Intel CPU model numbers and an
AMD/iommu uncore PMU driver fix"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/amd/iommu: Do not register a task ctx for uncore like PMUs
perf/x86: Add model numbers for Kabylake CPUs
Linus Torvalds [Fri, 6 May 2016 18:33:02 +0000 (11:33 -0700)]
Merge branch 'efi-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull EFI fixes from Ingo Molnar:
"This tree contains three fixes: a console spam fix, a file pattern fix
and a sysfb_efi fix for a bug that triggered on older ThinkPads"
* 'efi-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/sysfb_efi: Fix valid BAR address range check
x86/efi-bgrt: Switch all pr_err() to pr_notice() for invalid BGRT
MAINTAINERS: Remove asterisk from EFI directory names
Linus Torvalds [Fri, 6 May 2016 18:27:05 +0000 (11:27 -0700)]
Merge branch 'parisc-4.6-5' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc fix from Helge Deller:
"Patch from Dmitry V Levin to fix a kernel crash when a straced process
calls the (invalid) syscall which is equal to value of __NR_Linux_syscalls"
* 'parisc-4.6-5' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: fix a bug when syscall number of tracee is __NR_Linux_syscalls
Linus Torvalds [Fri, 6 May 2016 18:14:38 +0000 (11:14 -0700)]
Merge tag 'arc-4.6-rc7-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC fixes from Vineet Gupta:
"Late in the cycle, but this has fixes for couple of issues: a PAE40
boot crash and Arnd spotting lack of barriers in BE io-accessors.
The 3rd patch for enabling highmem in low physical mem ;-) honestly is
more than a "fix" but its been in works for some time, seems to be
stable in testing and enables 2 of our customers to go forward with
4.6 kernel.
- Fix for PTE truncation in PAE40 builds
- Fix for big endian IO accessors lacking IO barrier
- Allow HIGHMEM to work with low physical addresses"
* tag 'arc-4.6-rc7-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: support HIGHMEM even without PAE40
ARC: Fix PAE40 boot failures due to PTE truncation
ARC: Add missing io barriers to io{read,write}{16,32}be()
Linus Torvalds [Fri, 6 May 2016 17:59:53 +0000 (10:59 -0700)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Fixes for i915, amdgpu/radeon and imx.
The IMX fix is for an autoloading regression found in Fedora. The
radeon fixes, are the same fix to amdgpu/radeon to avoid a hardware
lockup in some circumstances with a bad mode, and a double free bug I
took a few hours chasing down the other morning.
The i915 fixes are across the board, all stable material, and fixing
some hangs and suspend/resume issues, along with a live status
regressions"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
gpu: ipu-v3: Fix imx-ipuv3-crtc module autoloading
drm/amdgpu: make sure vertical front porch is at least 1
drm/radeon: make sure vertical front porch is at least 1
drm/amdgpu: set metadata pointer to NULL after freeing.
drm/i915: Make RPS EI/thresholds multiple of 25 on SNB-BDW
drm/i915: Fake HDMI live status
drm/i915: Fix eDP low vswing for Broadwell
drm/i915/ddi: Fix eDP VDD handling during booting and suspend/resume
drm/i915: Fix system resume if PCI device remained enabled
drm/i915: Avoid stalling on pending flips for legacy cursor updates
Zygo Blaxell [Thu, 5 May 2016 04:23:49 +0000 (00:23 -0400)]
btrfs: don't force mounts to wait for cleaner_kthread to delete one or more subvolumes
During a mount, we start the cleaner kthread first because the transaction
kthread wants to wake up the cleaner kthread. We start the transaction
kthread next because everything in btrfs wants transactions. We do reloc
recovery in the thread that was doing the original mount call once the
transaction kthread is running. This means that the cleaner kthread
could already be running when reloc recovery happens (e.g. if a snapshot
delete was started before a crash).
Relocation does not play well with the cleaner kthread, so a mutex was
added in commit 5f3164813b90f7dbcb5c3ab9006906222ce471b7 "Btrfs: fix
race between balance recovery and root deletion" to prevent both from
being active at the same time.
If the cleaner kthread is already holding the mutex by the time we get
to btrfs_recover_relocation, the mount will be blocked until at least
one deleted subvolume is cleaned (possibly more if the mount process
doesn't get the lock right away). During this time (which could be an
arbitrarily long time on a large/slow filesystem), the mount process is
stuck and the filesystem is unnecessarily inaccessible.
Fix this by locking cleaner_mutex before we start cleaner_kthread, and
unlocking the mutex after mount no longer requires it. This ensures
that the mounting process will not be blocked by the cleaner kthread.
The cleaner kthread is already prepared for mutex contention and will
just go to sleep until the mutex is available.
Signed-off-by: Zygo Blaxell <ce3g8jdj@umail.furryterror.org> Reviewed-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
btrfs: fix lock dep warning move scratch super outside of chunk_mutex
Move scratch super outside of the chunk lock to avoid below
lockdep warning. The better place to scratch super is in
the function btrfs_rm_dev_replace_free_srcdev() just before
free_device, which is outside of the chunk lock as well.
Josef Bacik [Tue, 12 Apr 2016 16:54:40 +0000 (12:54 -0400)]
Btrfs: remove BUG_ON()'s in btrfs_map_block
btrfs_map_block can go horribly wrong in the face of fs corruption, lets agree
to not be assholes and panic at any possible chance things are all fucked up.
Signed-off-by: Josef Bacik <jbacik@fb.com>
[ removed type casts ] Signed-off-by: David Sterba <dsterba@suse.com>
Liu Bo [Wed, 27 Apr 2016 00:53:31 +0000 (17:53 -0700)]
Btrfs: fix divide error upon chunk's stripe_len
The struct 'map_lookup' uses type int for @stripe_len, while
btrfs_chunk_stripe_len() can return a u64 value, and it may end up with
@stripe_len being undefined value and it can lead to 'divide error' in
__btrfs_map_block().
This changes 'map_lookup' to use type u64 for stripe_len, also right now
we only use BTRFS_STRIPE_LEN for stripe_len, so this adds a valid checker for
BTRFS_STRIPE_LEN.
Reported-by: Vegard Nossum <vegard.nossum@oracle.com> Reported-by: Quentin Casasnovas <quentin.casasnovas@oracle.com> Signed-off-by: Liu Bo <bo.li.liu@oracle.com> Reviewed-by: David Sterba <dsterba@suse.com>
[ folded division fix to scrub_raid56_parity ] Signed-off-by: David Sterba <dsterba@suse.com>
David Sterba [Tue, 26 Apr 2016 14:22:06 +0000 (16:22 +0200)]
btrfs: sysfs: protect reading label by lock
If the label setting ioctl races with sysfs label handler, we could get
mixed result in the output, part old part new. We should either get the
old or new label. The chances to hit this race are low.
David Sterba [Thu, 24 Mar 2016 17:00:53 +0000 (18:00 +0100)]
btrfs: reuse existing variable in scrub_stripe, reduce stack usage
The key variable occupies 17 bytes, the key_start is used once, we can
simply reuse existing 'key' for that purpose. As the key is not a simple
type, compiler doest not do it on itself.
David Sterba [Thu, 24 Mar 2016 16:49:22 +0000 (17:49 +0100)]
btrfs: use dynamic allocation for root item in create_subvol
The size of root item is more than 400 bytes, which is quite a lot of
stack space. As we do IO from inside the subvolume ioctls, we should
keep the stack usage low in case the filesystem is on top of other
layers (NFS, device mapper, iscsi, etc).
Reviewed-by: Tsutomu Itoh <t-itoh@jp.fujitsu.com> Signed-off-by: David Sterba <dsterba@suse.com>
btrfs: fix lock dep warning, move scratch dev out of device_list_mutex and uuid_mutex
When the replace target fails, the target device will be taken
out of fs device list, scratch + update_dev_time and freed. However
we could do the scratch + update_dev_time and free part after the
device has been taken out of device list, so that we don't have to
hold the device_list_mutex and uuid_mutex locks.
Dan Carpenter [Wed, 13 Apr 2016 06:40:59 +0000 (09:40 +0300)]
btrfs: send: silence an integer overflow warning
The "sizeof(*arg->clone_sources) * arg->clone_sources_count" expression
can overflow. It causes several static checker warnings. It's all
under CAP_SYS_ADMIN so it's not that serious but lets silence the
warnings.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
Since mixed block groups accounting isn't byte-accurate and f_bree is an
unsigned integer, it could overflow. Avoid this.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com> Suggested-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
Currently, we don't allow the user to try and rebalance to a dup profile
on a multi-device filesystem. In most cases, this is a perfectly sensible
restriction as raid1 uses the same amount of space and provides better
protection.
However, when reshaping a multi-device filesystem down to a single device
filesystem, this requires the user to convert metadata and system chunks
to single profile before deleting devices, and then convert again to dup,
which leaves a period of time where metadata integrity is reduced.
This patch removes the single-device-only restriction from converting to
dup profile to remove this potential data integrity reduction.
Signed-off-by: Austin S. Hemmelgarn <ahferroin7@gmail.com> Signed-off-by: David Sterba <dsterba@suse.com>
parisc: fix a bug when syscall number of tracee is __NR_Linux_syscalls
Do not load one entry beyond the end of the syscall table when the
syscall number of a traced process equals to __NR_Linux_syscalls.
Similar bug with regular processes was fixed by commit 3bb457af4fa8
("[PARISC] Fix bug when syscall nr is __NR_Linux_syscalls").
Merge branches 'pm-opp-fixes', 'pm-cpufreq-fixes' and 'pm-cpuidle-fixes'
* pm-opp-fixes:
PM / OPP: Remove useless check
* pm-cpufreq-fixes:
intel_pstate: Fix intel_pstate_get()
cpufreq: intel_pstate: Fix HWP on boot CPU after system resume
cpufreq: st: enable selective initialization based on the platform
* pm-cpuidle-fixes:
ARM: cpuidle: Pass on arm_cpuidle_suspend()'s return value
Linus Torvalds [Fri, 6 May 2016 03:48:35 +0000 (20:48 -0700)]
Merge branch 'akpm' (patches from Andrew)
Merge fixes from Andrew Morton:
"14 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
byteswap: try to avoid __builtin_constant_p gcc bug
lib/stackdepot: avoid to return 0 handle
mm: fix kcompactd hang during memory offlining
modpost: fix module autoloading for OF devices with generic compatible property
proc: prevent accessing /proc/<PID>/environ until it's ready
mm/zswap: provide unique zpool name
mm: thp: kvm: fix memory corruption in KVM with THP enabled
MAINTAINERS: fix Rajendra Nayak's address
mm, cma: prevent nr_isolated_* counters from going negative
mm: update min_free_kbytes from khugepaged after core initialization
huge pagecache: mmap_sem is unlocked when truncation splits pmd
rapidio/mport_cdev: fix uapi type definitions
mm: memcontrol: let v2 cgroups follow changes in system swappiness
mm: thp: correct split_huge_pages file permission
Linus Torvalds [Fri, 6 May 2016 01:10:01 +0000 (18:10 -0700)]
Merge branch 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm fixes from Dan Williams:
- a fix for the persistent memory 'struct page' driver. The
implementation overlooked the fact that pages are allocated in 2MB
units leading to -ENOMEM when establishing some configurations.
It's tagged for -stable as the problem was introduced with the
initial implementation in 4.5.
- The new "error status translation" routine, introduced with the 4.6
updates to the nfit driver, missed a necessary path in
acpi_nfit_ctl().
The end result is that we are falsely assuming commands complete
successfully when the embedded status says otherwise.
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
nfit: fix translation of command status results
libnvdimm, pfn: fix memmap reservation sizing
Arnd Bergmann [Thu, 5 May 2016 23:22:39 +0000 (16:22 -0700)]
byteswap: try to avoid __builtin_constant_p gcc bug
This is another attempt to avoid a regression in wwn_to_u64() after that
started using get_unaligned_be64(), which in turn ran into a bug on
gcc-4.9 through 6.1.
The regression got introduced due to the combination of two separate
workarounds (commits e3bde9568d99: "include/linux/unaligned: force
inlining of byteswap operations" and ef3fb2422ffe: "scsi: fc: use
get/put_unaligned64 for wwn access") that each try to sidestep distinct
problems with gcc behavior (code growth and increased stack usage).
Unfortunately after both have been applied, a more serious gcc bug has
been uncovered, leading to incorrect object code that discards part of a
function and causes undefined behavior.
As part of this problem is how __builtin_constant_p gets evaluated on an
argument passed by reference into an inline function, this avoids the
use of __builtin_constant_p() for all architectures that set
CONFIG_ARCH_USE_BUILTIN_BSWAP. Most architectures do not set
ARCH_SUPPORTS_OPTIMIZED_INLINING, which means they probably do not
suffer from the problem in the qla2xxx driver, but they might still run
into it elsewhere.
Both of the original workarounds were only merged in the 4.6 kernel, and
the bug that is fixed by this patch should only appear if both are
there, so we probably don't need to backport the fix. On the other
hand, it works by simplifying the code path and should not have any
negative effects.
[arnd@arndb.de: fix older gcc warnings]
(http://lkml.kernel.org/r/12243652.bxSxEgjgfk@wuerfel) Link: https://lkml.org/lkml/headers/2016/4/12/1103 Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=66122 Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=70232 Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=70646 Fixes: e3bde9568d99 ("include/linux/unaligned: force inlining of byteswap operations") Fixes: ef3fb2422ffe ("scsi: fc: use get/put_unaligned64 for wwn access") Link: http://lkml.kernel.org/r/1780465.XdtPJpi8Tt@wuerfel Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Josh Poimboeuf <jpoimboe@redhat.com> Tested-by: Josh Poimboeuf <jpoimboe@redhat.com> # on gcc-5.3 Tested-by: Quinn Tran <quinn.tran@qlogic.com> Cc: Martin Jambor <mjambor@suse.cz> Cc: "Martin K. Petersen" <martin.petersen@oracle.com> Cc: James Bottomley <James.Bottomley@hansenpartnership.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: Thomas Graf <tgraf@suug.ch> Cc: Peter Zijlstra <peterz@infradead.org> Cc: David Rientjes <rientjes@google.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Himanshu Madhani <himanshu.madhani@qlogic.com> Cc: Jan Hubicka <hubicka@ucw.cz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Joonsoo Kim [Thu, 5 May 2016 23:22:35 +0000 (16:22 -0700)]
lib/stackdepot: avoid to return 0 handle
Recently, we allow to save the stacktrace whose hashed value is 0. It
causes the problem that stackdepot could return 0 even if in success.
User of stackdepot cannot distinguish whether it is success or not so we
need to solve this problem. In this patch, 1 bit are added to handle
and make valid handle none 0 by setting this bit. After that, valid
handle will not be 0 and 0 handle will represent failure correctly.
Fixes: 33334e25769c ("lib/stackdepot.c: allow the stack trace hash to be zero") Link: http://lkml.kernel.org/r/1462252403-1106-1-git-send-email-iamjoonsoo.kim@lge.com Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: Alexander Potapenko <glider@google.com> Cc: Andrey Ryabinin <aryabinin@virtuozzo.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
projects / linux-beck.git / log