Peter Ujfalusi [Fri, 16 Jun 2017 15:40:58 +0000 (10:40 -0500)]
usb: musb: tusb6010_omap: Use one musb_ep_select call in tusb_omap_dma_program
Having one musb_ep_select() instead the two calls in if/else is the same
thing, but makes the code a bit simpler to follow.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Tested-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Bin Liu <b-liu@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Ujfalusi [Fri, 16 Jun 2017 15:40:57 +0000 (10:40 -0500)]
usb: musb: tusb6010: Add MUSB_G_NO_SKB_RESERVE to quirks
When using the g_ncm for networking this flag will make sure that the
buffer is aligned to 32bit so the DMA can be used to offload the data
movement.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Tested-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Bin Liu <b-liu@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Ujfalusi [Fri, 16 Jun 2017 15:40:56 +0000 (10:40 -0500)]
usb: musb: Add quirk to avoid skb reserve in gadget mode
For tusb6010 the DMA functionality only possible if the buffer is 32bit
aligned (SYNC access to FIFO) since with ASYNC access the TX/RX offset
registers will corrupt eventually.
The MUSB_G_NO_SKB_RESERVE will set the quirk_avoids_skb_reserve flag in
usb_gadget struct to provide correctly aligned buffer.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Tested-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Bin Liu <b-liu@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Ujfalusi [Fri, 16 Jun 2017 15:40:55 +0000 (10:40 -0500)]
dmaengine: omap-dma: port_window support correction for both direction
When the port_window support was verified it was done on setup where only
the MEM_TO_DEV direction was enabled. This got un-noticed and thus only
this direction worked.
Now that I have managed to get a setup to verify both direction it turned
out that the setup was incorrect:
omap_desc members are settings for the slave port while the omap_sg members
apply to the memory side of the sDMA setup.
Fixes: 527a27591312 ("dmaengine: omap-dma: Fix the port_window support") Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Cc: Russell King <linux@armlinux.org.uk> Cc: dmaengine@vger.kernel.org Cc: dan.j.williams@intel.com Cc: vinod.koul@intel.com Tested-by: Tony Lindgren <tony@atomide.com> Acked-by: Vinod Koul <vinod.koul@intel.com> Signed-off-by: Bin Liu <b-liu@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alexandre Bailon [Fri, 16 Jun 2017 15:40:54 +0000 (10:40 -0500)]
usb: musb: musb_cppi41: Defer probe only if DMA is not ready
If dma_request_slave_channel() failed to return a channel,
then the driver will print an error and request to defer probe,
regardless of the cause of the failure.
Defer if the DMA is not ready yet otherwise print an error.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com> Reviewed-by: Johan Hovold <johan@kernel.org> Signed-off-by: Bin Liu <b-liu@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Merge tag 'usb-for-v4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-testing
Felipe writes:
usb: changes for v4.13 merge window
This time around we have a total of 57 non-merge commits. A list of
most important changes follows:
- Improvements to dwc3 tracing interface
- Initial dual-role support for dwc3
- Improvements to how we handle DMA resources in dwc3
- A new f_uac1 implementation which much more flexible
- Removal of AVR32 bits
- Improvements to f_mass_storage driver
Hugh Dickins [Mon, 19 Jun 2017 11:03:24 +0000 (04:03 -0700)]
mm: larger stack guard gap, between vmas
Stack guard page is a useful feature to reduce a risk of stack smashing
into a different mapping. We have been using a single page gap which
is sufficient to prevent having stack adjacent to a different mapping.
But this seems to be insufficient in the light of the stack usage in
userspace. E.g. glibc uses as large as 64kB alloca() in many commonly
used functions. Others use constructs liks gid_t buffer[NGROUPS_MAX]
which is 256kB or stack strings with MAX_ARG_STRLEN.
This will become especially dangerous for suid binaries and the default
no limit for the stack size limit because those applications can be
tricked to consume a large portion of the stack and a single glibc call
could jump over the guard page. These attacks are not theoretical,
unfortunatelly.
Make those attacks less probable by increasing the stack guard gap
to 1MB (on systems with 4k pages; but make it depend on the page size
because systems with larger base pages might cap stack allocations in
the PAGE_SIZE units) which should cover larger alloca() and VLA stack
allocations. It is obviously not a full fix because the problem is
somehow inherent, but it should reduce attack space a lot.
One could argue that the gap size should be configurable from userspace,
but that can be done later when somebody finds that the new 1MB is wrong
for some special case applications. For now, add a kernel command line
option (stack_guard_gap) to specify the stack gap size (in page units).
Implementation wise, first delete all the old code for stack guard page:
because although we could get away with accounting one extra page in a
stack vma, accounting a larger gap can break userspace - case in point,
a program run with "ulimit -S -v 20000" failed when the 1MB gap was
counted for RLIMIT_AS; similar problems could come with RLIMIT_MLOCK
and strict non-overcommit mode.
Instead of keeping gap inside the stack vma, maintain the stack guard
gap as a gap between vmas: using vm_start_gap() in place of vm_start
(or vm_end_gap() in place of vm_end if VM_GROWSUP) in just those few
places which need to respect the gap - mainly arch_get_unmapped_area(),
and and the vma tree's subtree_gap support for that.
Ruslan Bilovol [Sun, 18 Jun 2017 13:23:54 +0000 (16:23 +0300)]
usb: gadget: add f_uac1 variant based on a new u_audio api
This patch adds a new function 'f_uac1'
(f_uac1 with virtual "ALSA card") that
uses recently created u_audio API. Comparing
to legacy f_uac1 function implementation it
doesn't require any real Audio codec to be
present on the device. In f_uac1 audio
streams are simply sinked to and sourced
from a virtual ALSA sound card created
using u_audio API.
Legacy f_uac1 approach is to write audio
samples directly to existing ALSA sound
card
f_uac1 approach is more generic/flexible
one - create an ALSA sound card that
represents USB Audio function and allows to
be used by userspace application that
may choose to do whatever it wants with the
data received from the USB Host and choose
to provide whatever it wants as audio data
to the USB Host.
f_uac1 also has capture support (gadget->host)
thanks to easy implementation via u_audio.
By default, capture interface has 48000kHz/2ch
configuration, same as playback channel has.
f_uac1 descriptors naming convention
uses f_uac2 driver naming convention that
makes it more common and meaningful.
Comparing to f_uac1_legacy, the f_uac1 doesn't
have volume/mute functionality. This is because
the f_uac1 volume/mute feature unit was dummy
implementation since that driver creation (2009)
and never had any real volume control or mute
functionality, so there is no any difference
here.
Since f_uac1 functionality, exposed
interface to userspace (virtual ALSA card),
input parameters are so different comparing
to f_uac1_legacy, that there is no any
reason to keep them in the same file/module,
and separate function was created.
g_audio can be built using one of existing
UAC functions (f_uac1, f_uac1_legacy or f_uac2)
Signed-off-by: Ruslan Bilovol <ruslan.bilovol@gmail.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Ruslan Bilovol [Sun, 18 Jun 2017 13:23:52 +0000 (16:23 +0300)]
usb: gadget: f_uac2: split out audio core
Abstract the peripheral side ALSA sound card code from
the f_uac2 function into a component that can be called
by various functions, so the various flavors can be split
apart and selectively reused.
Visible changes:
- add uac_params structure to pass audio paramteres for
g_audio_setup
- make ALSA sound card's name configurable
- add [in/out]_ep_maxpsize
- allocate snd_uac_chip structure during g_audio_setup
- add u_audio_[start/stop]_[capture/playback] functions
Signed-off-by: Ruslan Bilovol <ruslan.bilovol@gmail.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Simplify f_uac2 by removing platform driver/device
creation; use composite's usb_gadget device as
parent for sound card and for debug prints.
This removes extra layer of code without any functional
change.
Signed-off-by: Ruslan Bilovol <ruslan.bilovol@gmail.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
After commit 7e4da3fcf7c9 ("usb: gadget: composite:
Test get_alt() presence instead of set_alt()") f_uac1
function became broken because it doesn't have
get_alt() callback implementation and composite
framework never set altsetting 1 for audiostreaming
interface. On host site it looks like:
Since host can't set altsetting 1, it can't start
playing audio.
In order to fix it implemented get_alt along with
minor improvements (error conditions checking)
similar to what existing f_uac2 has.
Cc: Krzysztof Opasiak <k.opasiak@samsung.com> Signed-off-by: Ruslan Bilovol <ruslan.bilovol@gmail.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
commit 46ddd79e893b ("usb: gadget: udc: atmel: Remove AVR32 bits from the
driver") left the accessor macros introduced by commit a3dd3befd7cb ("usb:
gadget: atmel_usba: use endian agnostic IO on ARM"). They can now be
removed.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Srinath Mannam [Thu, 15 Jun 2017 09:09:22 +0000 (14:39 +0530)]
usb: gadget: bdc: 64-bit pointer capability check
Corrected the register to check the 64-bit pointer
capability state. 64-bit pointer implementation capability
was checking in wrong register, which causes the BDC
enumeration failure in 64-bit memory address.
Fixes: efed421a94e6 ("usb: gadget: Add UDC driver for
Broadcom USB3.0 device controller IP BDC")
Olof Johansson [Mon, 19 Jun 2017 03:42:21 +0000 (20:42 -0700)]
Merge tag 'sunxi-fixes-for-4.12' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into fixes
Allwinner fixes for 4.12
A few fixes around the PRCM support that got in 4.12 with a wrong
compatible, and a missing clock in the binding.
* tag 'sunxi-fixes-for-4.12' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: allwinner: a64: Add PLL_PERIPH0 clock to the R_CCU
ARM: sunxi: h3-h5: Add PLL_PERIPH0 clock to the R_CCU
arm64: allwinner: h5: Remove syslink to shared DTSI
ARM: sunxi: h3/h5: fix the compatible of R_CCU
Linus Torvalds [Mon, 19 Jun 2017 00:25:05 +0000 (09:25 +0900)]
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio bugfix from Michael Tsirkin:
"It turns out balloon does not handle IOMMUs correctly. We should fix
that at some point, for now let's just disable this configuration"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio_balloon: disable VIOMMU support
Linus Torvalds [Mon, 19 Jun 2017 00:20:25 +0000 (09:20 +0900)]
Merge branch 'i2c/for-current-fixed' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"Two driver bugfixes"
* 'i2c/for-current-fixed' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: ismt: fix wrong device address when unmap the data buffer
i2c: rcar: use correct length when unmapping DMA
Linus Torvalds [Mon, 19 Jun 2017 00:01:01 +0000 (09:01 +0900)]
Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Pull MIPS fixes from Ralf Baechle:
- Three highmem fixes:
+ Fixed mapping initialization
+ Adjust the pkmap location
+ Ensure we use at most one page for PTEs
- Fix makefile dependencies for .its targets to depend on vmlinux
- Fix reversed condition in BNEZC and JIALC software branch emulation
- Only flush initialized flush_insn_slot to avoid NULL pointer
dereference
- perf: Remove incorrect odd/even counter handling for I6400
- ftrace: Fix init functions tracing
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: .its targets depend on vmlinux
MIPS: Fix bnezc/jialc return address calculation
MIPS: kprobes: flush_insn_slot should flush only if probe initialised
MIPS: ftrace: fix init functions tracing
MIPS: mm: adjust PKMAP location
MIPS: highmem: ensure that we don't use more than one page for PTEs
MIPS: mm: fixed mappings: correct initialisation
MIPS: perf: Remove incorrect odd/even counter handling for I6400
virtio balloon bypasses the DMA API entirely so does not support the
VIOMMU right now. It's not clear we need that support, for now let's
just make sure we don't pretend to support it.
Cc: stable@vger.kernel.org Cc: Wei Wang <wei.w.wang@intel.com> Fixes: 1a937693993f ("virtio: new feature to detect IOMMU device quirk") Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Jason Wang <jasowang@redhat.com>
Linus Torvalds [Sun, 18 Jun 2017 09:49:12 +0000 (18:49 +0900)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"Two fixlets for x86:
- Handle WARN_ONs proper with the new UD based WARN implementation
- Disable 1G mappings when 2M mappings are disabled by kmemleak or
debug_pagealloc. Otherwise 1G mappings might still be used,
confusing the debug mechanisms"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mm: Disable 1GB direct mappings when disabling 2MB mappings
x86/debug: Handle early WARN_ONs proper
Linus Torvalds [Sun, 18 Jun 2017 09:46:51 +0000 (18:46 +0900)]
Merge branch 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fixes from Thomas Gleixner:
"Three fixlets for timers:
- Two hot-fixes for the alarmtimer based posix timers, which prevent
a nasty DOS by self rescheduling timers. The proper cleanup of that
mess is queued for 4.13
- Make a function static"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tick/broadcast: Make tick_broadcast_setup_oneshot() static
alarmtimer: Rate limit periodic intervals
alarmtimer: Prevent overflow of relative timers
Linus Torvalds [Sun, 18 Jun 2017 09:45:17 +0000 (18:45 +0900)]
Merge branch 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fixes from Thomas Gleixner:
"Two small fixes for the schedulre core:
- Use the proper switch_mm() variant in idle_task_exit() because that
code is not called with interrupts disabled.
- Fix a confusing typo in a printk"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/core: Idle_task_exit() shouldn't use switch_mm_irqs_off()
sched/fair: Fix typo in printk message
Linus Torvalds [Sat, 17 Jun 2017 23:51:35 +0000 (08:51 +0900)]
Merge tag 'led_fixes_for_4.12-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds
Pull LED fixes from Jacek Anaszewski:
"Two LED fixes:
- fix signal source assignment for leds-bcm6328
- revert patch that intended to fix LED behavior on suspend but it
had a side effect preventing suspend at all due to uevent being
sent on trigger removal"
* tag 'led_fixes_for_4.12-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds:
Revert "leds: handle suspend/resume in heartbeat trigger"
leds: bcm6328: fix signal source assignment for leds 4 to 7
Linus Torvalds [Sat, 17 Jun 2017 23:39:54 +0000 (08:39 +0900)]
Merge tag 'usb-4.12-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some small gadget and xhci USB fixes for 4.12-rc6.
Nothing major, but one of the gadget patches does fix a reported oops,
and the xhci ones resolve reported problems. All have been in
linux-next with no reported issues"
* tag 'usb-4.12-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: gadgetfs, dummy-hcd, net2280: fix locking for callbacks
usb: xhci: ASMedia ASM1042A chipset need shorts TX quirk
usb: xhci: Fix USB 3.1 supported protocol parsing
USB: gadget: fix GPF in gadgetfs
usb: gadget: composite: make sure to reactivate function on unbind
Linus Torvalds [Sat, 17 Jun 2017 23:23:02 +0000 (08:23 +0900)]
Merge tag 'ceph-for-4.12-rc6' of git://github.com/ceph/ceph-client
Pull ceph fixes from Ilya Dryomov:
"A fix for an old ceph ->fh_to_* bug from Luis and two timestamp fixups
from Zheng, prompted by the ongoing y2038 work"
* tag 'ceph-for-4.12-rc6' of git://github.com/ceph/ceph-client:
ceph: unify inode i_ctime update
ceph: use current_kernel_time() to get request time stamp
ceph: check i_nlink while converting a file handle to dentry
Linus Torvalds [Sat, 17 Jun 2017 08:30:07 +0000 (17:30 +0900)]
Merge branch 'ufs-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull ufs fixes from Al Viro:
"Fix assorted ufs bugs: a couple of deadlocks, fs corruption in
truncate(), oopsen on tail unpacking and truncate when racing with
vmscan, mild fs corruption (free blocks stats summary buggered, *BSD
fsck would complain and fix), several instances of broken logics
around reserved blocks (starting with "check almost never triggers
when it should" and then there are issues with sufficiently large
UFS2)"
[ Note: ufs hasn't gotten any loving in a long time, because nobody
really seems to use it. These ufs fixes are triggered by people
actually caring now, not some sudden influx of new bugs. - Linus ]
* 'ufs-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
ufs_truncate_blocks(): fix the case when size is in the last direct block
ufs: more deadlock prevention on tail unpacking
ufs: avoid grabbing ->truncate_mutex if possible
ufs_get_locked_page(): make sure we have buffer_heads
ufs: fix s_size/s_dsize users
ufs: fix reserved blocks check
ufs: make ufs_freespace() return signed
ufs: fix logics in "ufs: make fsck -f happy"
Linus Torvalds [Sat, 17 Jun 2017 08:26:53 +0000 (17:26 +0900)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs fixes from Al Viro:
"A couple of fixes; a leak in mntns_install() caught by Andrei (this
cycle regression) + d_invalidate() softlockup fix - that had been
reported by a bunch of people lately, but the problem is pretty old"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fs: don't forget to put old mntns in mntns_install
Hang/soft lockup in d_invalidate with simultaneous calls
Linus Torvalds [Fri, 16 Jun 2017 21:53:20 +0000 (06:53 +0900)]
Merge tag 'pci-v4.12-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
- fix another PCI_ENDPOINT build error (merged for v4.12)
- fix error codes added to config accessors for v4.12
* tag 'pci-v4.12-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: endpoint: Select CRC32 to fix test build error
PCI: Make error code types consistent in pci_{read,write}_config_*
Linus Torvalds [Fri, 16 Jun 2017 21:49:34 +0000 (06:49 +0900)]
Merge branch 'akpm' (patches from Andrew)
Merge misc fixes from Andrew Morton:
"5 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
mm: correct the comment when reclaimed pages exceed the scanned pages
userfaultfd: shmem: handle coredumping in handle_userfault()
mm: numa: avoid waiting on freed migrated pages
swap: cond_resched in swap_cgroup_prepare()
mm/memory-failure.c: use compound_head() flags for huge pages
zhongjiang [Fri, 16 Jun 2017 21:02:40 +0000 (14:02 -0700)]
mm: correct the comment when reclaimed pages exceed the scanned pages
Commit e1587a494540 ("mm: vmpressure: fix sending wrong events on
underflow") declared that reclaimed pages exceed the scanned pages due
to the thp reclaim.
That is incorrect because THP will be spilt to normal page and loop
again, which will result in the scanned pages increment.
Andrea Arcangeli [Fri, 16 Jun 2017 21:02:37 +0000 (14:02 -0700)]
userfaultfd: shmem: handle coredumping in handle_userfault()
Anon and hugetlbfs handle FOLL_DUMP set by get_dump_page() internally to
__get_user_pages().
shmem as opposed has no special FOLL_DUMP handling there so
handle_mm_fault() is invoked without mmap_sem and ends up calling
handle_userfault() that isn't expecting to be invoked without mmap_sem
held.
This makes handle_userfault() fail immediately if invoked through
shmem_vm_ops->fault during coredumping and solves the problem.
The side effect is a BUG_ON with no lock held triggered by the
coredumping process which exits. Only 4.11 is affected, pre-4.11 anon
memory holes are skipped in __get_user_pages by checking FOLL_DUMP
explicitly against empty pagetables (mm/gup.c:no_page_table()).
It's zero cost as we already had a check for current->flags to prevent
futex to trigger userfaults during exit (PF_EXITING).
Link: http://lkml.kernel.org/r/20170615214838.27429-1-aarcange@redhat.com Signed-off-by: Andrea Arcangeli <aarcange@redhat.com> Reported-by: "Dr. David Alan Gilbert" <dgilbert@redhat.com> Cc: <stable@vger.kernel.org> [4.11+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mark Rutland [Fri, 16 Jun 2017 21:02:34 +0000 (14:02 -0700)]
mm: numa: avoid waiting on freed migrated pages
In do_huge_pmd_numa_page(), we attempt to handle a migrating thp pmd by
waiting until the pmd is unlocked before we return and retry. However,
we can race with migrate_misplaced_transhuge_page():
// do_huge_pmd_numa_page // migrate_misplaced_transhuge_page()
// Holds 0 refs on page // Holds 2 refs on page
vmf->ptl = pmd_lock(vma->vm_mm, vmf->pmd);
/* ... */
if (pmd_trans_migrating(*vmf->pmd)) {
page = pmd_page(*vmf->pmd);
spin_unlock(vmf->ptl);
ptl = pmd_lock(mm, pmd);
if (page_count(page) != 2)) {
/* roll back */
}
/* ... */
mlock_migrate_page(new_page, page);
/* ... */
spin_unlock(ptl);
put_page(page);
put_page(page); // page freed here
wait_on_page_locked(page);
goto out;
}
This can result in the freed page having its waiters flag set
unexpectedly, which trips the PAGE_FLAGS_CHECK_AT_PREP checks in the
page alloc/free functions. This has been observed on arm64 KVM guests.
We can avoid this by having do_huge_pmd_numa_page() take a reference on
the page before dropping the pmd lock, mirroring what we do in
__migration_entry_wait().
When we hit the race, migrate_misplaced_transhuge_page() will see the
reference and abort the migration, as it may do today in other cases.
Fixes: b8916634b77bffb2 ("mm: Prevent parallel splits during THP migration") Link: http://lkml.kernel.org/r/1497349722-6731-2-git-send-email-will.deacon@arm.com Signed-off-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Acked-by: Steve Capper <steve.capper@arm.com> Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Acked-by: Vlastimil Babka <vbabka@suse.cz> Cc: Mel Gorman <mgorman@suse.de> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
James Morse [Fri, 16 Jun 2017 21:02:29 +0000 (14:02 -0700)]
mm/memory-failure.c: use compound_head() flags for huge pages
memory_failure() chooses a recovery action function based on the page
flags. For huge pages it uses the tail page flags which don't have
anything interesting set, resulting in:
> Memory failure: 0x9be3b4: Unknown page state
> Memory failure: 0x9be3b4: recovery action for unknown page: Failed
Instead, save a copy of the head page's flags if this is a huge page,
this means if there are no relevant flags for this tail page, we use the
head pages flags instead. This results in the me_huge_page() recovery
action being called:
> Memory failure: 0x9b7969: recovery action for huge page: Delayed
For hugepages that have not yet been allocated, this allows the hugepage
to be dequeued.
Fixes: 524fca1e7356 ("HWPOISON: fix misjudgement of page_action() for errors on mlocked pages") Link: http://lkml.kernel.org/r/20170524130204.21845-1-james.morse@arm.com Signed-off-by: James Morse <james.morse@arm.com> Tested-by: Punit Agrawal <punit.agrawal@arm.com> Acked-by: Punit Agrawal <punit.agrawal@arm.com> Acked-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 16 Jun 2017 20:57:54 +0000 (05:57 +0900)]
Merge tag 'powerpc-4.12-6' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"Three small fixes for recently merged code:
- remove a spurious WARN_ON when a PCI device has no of_node, it's
allowed in some circumstances for there to be no of_node.
- fix the offset for store EOI MMIOs in the XIVE interrupt
controller.
- fix non-const WARN_ONs which were becoming BUGs due to them losing
BUGFLAG_WARNING in a recent cleanup patch.
Thanks to: Alexey Kardashevskiy, Alistair Popple, Benjamin
Herrenschmidt"
* tag 'powerpc-4.12-6' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/debug: Add missing warn flag to WARN_ON's non-builtin path
powerpc/xive: Fix offset for store EOI MMIOs
powerpc/npu-dma: Remove spurious WARN_ON when a PCI device has no of_node
Ingo Molnar [Fri, 16 Jun 2017 19:33:48 +0000 (21:33 +0200)]
Merge tag 'perf-urgent-for-mingo-4.12-20170616' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/urgent
Pull perf/urgent fixes from Arnaldo Carvalho de Melo:
- Fix probing of precise_ip level for default cycles event, that
got broken recently on x86_64 when its arch code started
considering invalid requesting precise samples when not sampling
(i.e. when attr.sample_period == 0).
This also fixes another problem in s/390 where the precision
probing with sample_period == 0 returned precise_ip > 0, that
then, when setting up the real cycles event (not probing) would
return EOPNOTSUPP for precise_ip > 0 (as determined previously
by probing) and sample_period > 0.
These problems resulted in attr_precise not being set to the
highest precision available on x86.64 when no event was specified,
i.e. the canonical:
perf record ./workload
would end up using attr.precise_ip = 0. As a workaround this would
need to be done:
perf record -e cycles:P ./workload
And on s/390 it would plain not work, requiring using:
perf record -e cycles ./workload
as a workaround. (Arnaldo Carvalho de Melo)
- Fix perf build with ARCH=x86_64, when ARCH should be transformed
into ARCH=x86, just like with the main kernel Makefile and
tools/objtool's, i.e. use SRCARCH. (Jiada Wang)
- Avoid accessing uninitialized data structures when unwinding with
elfutils's libdw, making it more closely mimic libunwind's unwinder.
(Milian Wolff)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Ingo Molnar <mingo@kernel.org>
Milian Wolff [Fri, 2 Jun 2017 14:37:53 +0000 (16:37 +0200)]
perf unwind: Report module before querying isactivation in dwfl unwind
The PC returned by dwfl_frame_pc() may map into a not-yet-reported
module. We have to report it before we continue unwinding. But when we
query for the isactivation flag in dwfl_frame_pc, libdw will actually do
one more unwinding step internally which can then break and lead to
missed frames or broken stacks.
Merge tag 'phy-for-4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next
Kishon writes:
phy: for 4.13
*) Group phy drivers into vendor specific directories
*) Add USB3 PHY driver for Renesas R-Car Gen3
*) Add USB2 PHY driver for Meson GXL and GXM SoCs
*) Add USB DRD PHY driver for Broadcom Northstar2
*) Add USB PHY driver for CPCAP PMIC USB
*) Make phy-meson8b-usb2 driver support USB PHY on Meson8
*) Make phy-tusb1210 driver support TUSB1211
*) Make phy-rockchip-inno-usb2 driver support usb2-phy in rk3228 SoCs
*) Make phy-brcm-sata driver support for stingray SATA phy
*) Make bcm-ns-usb3 as a MDIO driver
*) Make rockchip-inno-usb2 support two host ports
*) Implement ->set_mode() callback in phy-tusb1210
*) Minor fixes in phy drivers
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Linus Torvalds [Fri, 16 Jun 2017 09:45:47 +0000 (18:45 +0900)]
Merge tag 'configfs-for-4.12' of git://git.infradead.org/users/hch/configfs
Pull configfs updates from Christoph Hellwig:
"A fix from Nic for a race seen in production (including a stable tag).
And while I'm sending you this I'm also sneaking in a trivial new
helper from Bart so that we don't need inter-tree dependencies for the
next merge window"
* tag 'configfs-for-4.12' of git://git.infradead.org/users/hch/configfs:
configfs: Introduce config_item_get_unless_zero()
configfs: Fix race between create_link and configfs_rmdir
Linus Torvalds [Fri, 16 Jun 2017 08:46:47 +0000 (17:46 +0900)]
Merge tag 'drm-fixes-for-v4.12-rc6' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"This is the main fixes pull for 4.12-rc6, all pretty normal for this
stage, nothing really stands out. The mxsfb one is probably the
largest and it's for a black screen boot problem.
AMD, i915, mgag200, msxfb, tegra fixes"
* tag 'drm-fixes-for-v4.12-rc6' of git://people.freedesktop.org/~airlied/linux:
drm: mxsfb_crtc: Reset the eLCDIF controller
drm/mgag200: Fix to always set HiPri for G200e4 V2
drm/tegra: Correct idr_alloc() minimum id
drm/tegra: Fix lockup on a use of staging API
gpu: host1x: Fix error handling
drm/radeon: Fix overflow of watermark calcs at > 4k resolutions.
drm/amdgpu: Fix overflow of watermark calcs at > 4k resolutions.
drm/radeon: fix "force the UVD DPB into VRAM as well"
drm/i915: Fix GVT-g PVINFO version compatibility check
drm/i915: Fix SKL+ watermarks for 90/270 rotation
drm/i915: Fix scaling check for 90/270 degree plane rotation
drm: dw-hdmi: Fix compilation breakage by selecting REGMAP_MMIO
Linus Torvalds [Fri, 16 Jun 2017 08:38:23 +0000 (17:38 +0900)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma fixes from Doug Ledford:
"I had thought at the time of the last pull request that there wouldn't
be much more to go, but several things just kept trickling in over the
last week.
Instead of just the six patches to bnxt_re that I had anticipated,
there are another five IPoIB patches, two qedr patches, and a few
other miscellaneous patches.
The bnxt_re patches are more lines of diff than I like to submit this
late in the game. That's mostly because of the first two patches in
the series of six. I almost dropped them just because of the lines of
churn, but on a close review, a lot of the churn came from removing
duplicated code sections and consolidating them into callable
routines. I felt like this made the number of lines of change more
acceptable, and they address problems, so I left them. The remainder
of the patches are all small, well contained, and well understood.
These have passed 0day testing, but have not been submitted to
linux-next (but a local merge test with your current master was
without any conflicts).
Summary:
- A fix for fix eea40b8f624 ("infiniband: call ipv6 route lookup via
the stub interface")
- Six patches against bnxt_re...the first two are considerably larger
than I would like, but as they address real issues I went ahead and
submitted them (it also helped that a good deal of the churn was
removing code repeated in multiple places and consolidating it to
one common function)
- Two fixes against qedr that just came in
- One fix against rxe that took a few revisions to get right plus
time to get the proper reviews
- Five late breaking IPoIB fixes
- One late cxgb4 fix"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma:
rdma/cxgb4: Fix memory leaks during module exit
IB/ipoib: Fix memory leak in create child syscall
IB/ipoib: Fix access to un-initialized napi struct
IB/ipoib: Delete napi in device uninit default
IB/ipoib: Limit call to free rdma_netdev for capable devices
IB/ipoib: Fix memory leaks for child interfaces priv
rxe: Fix a sleep-in-atomic bug in post_one_send
RDMA/qedr: Add 64KB PAGE_SIZE support to user-space queues
RDMA/qedr: Initialize byte_len in WC of READ and SEND commands
RDMA/bnxt_re: Remove FMR support
RDMA/bnxt_re: Fix RQE posting logic
RDMA/bnxt_re: Add HW workaround for avoiding stall for UD QPs
RDMA/bnxt_re: Dereg MR in FW before freeing the fast_reg_page_list
RDMA/bnxt_re: HW workarounds for handling specific conditions
RDMA/bnxt_re: Fixing the Control path command and response handling
IB/addr: Fix setting source address in addr6_resolve()
Linus Torvalds [Fri, 16 Jun 2017 08:30:44 +0000 (17:30 +0900)]
Merge tag 'platform-drivers-x86-v4.12-2' of git://git.infradead.org/linux-platform-drivers-x86
Pull x86 platform driver fix from Darren Hart:
"Just a single patch to fix an oops in the intel_telemetry_debugfs
module load/unload"
* tag 'platform-drivers-x86-v4.12-2' of git://git.infradead.org/linux-platform-drivers-x86:
platform/x86: intel_telemetry_debugfs: fix oops when load/unload module
Linus Torvalds [Fri, 16 Jun 2017 08:13:06 +0000 (17:13 +0900)]
Merge branch 'dmi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging
Pull dmi fixes from Jean Delvare.
* 'dmi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
firmware: dmi_scan: Check DMI structure length
firmware: dmi: Fix permissions of product_family
firmware: dmi_scan: Make dmi_walk and dmi_walk_early return real error codes
firmware: dmi_scan: Look for SMBIOS 3 entry point first
Rafał Miłecki [Thu, 8 Jun 2017 20:04:28 +0000 (22:04 +0200)]
phy: bcm-ns-usb3: add MDIO driver using proper bus layer
As USB 3.0 PHY is attached to the MDIO bus this module should provide a
MDIO driver and use a proper bus layer. This is a proper (cleaner)
solution which doesn't require code to know this specific MDIO bus
details. It also allows reusing the driver with other MDIO buses.
For now keep platform device support in place. We may consider dropping
it once MDIO bindings gets used "everywhere".
Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Rafał Miłecki [Thu, 8 Jun 2017 20:04:27 +0000 (22:04 +0200)]
dt-bindings: phy: Modify Broadcom NS USB 3.0 PHY binding to use MDIO
Thanks to work done by Broadcom explaining their USB 3.0 PHY details we
know it's attached to the MDIO bus. Use this knowledge to update the
binding: make it a subnode to the MDIO bus and rework way of specifying
required registers. This will describe hardware more precisely and will
allow to support (describe) more devices attached to the MDIO.
While compatibility strings remain the same there isn't a direct
conflict (compatibility breakage) for the binding. Originally it wasn't
supposed to be used for MDIO subnode so this change should be safe
unless some operating system was probing MDIO subnodes as standalone
devices.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Rafał Miłecki [Thu, 8 Jun 2017 20:04:26 +0000 (22:04 +0200)]
phy: bcm-ns-usb3: enable MDIO in the platform specific code
When we finally start using MDIO layer then bus initialization will be
handled in a separated driver. It means our code handling this has to be
used for the platform driver only.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Rafał Miłecki [Thu, 8 Jun 2017 20:04:25 +0000 (22:04 +0200)]
phy: bcm-ns-usb3: use pointer for PHY writing function
Our current writing function accesses PHY directly bypassing MDIO layer.
The aim is to extend this module to also behave as MDIO driver. This
will require using different writing function which can be handled
cleanly by having an extra pointer like this.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Rafał Miłecki [Thu, 8 Jun 2017 20:04:24 +0000 (22:04 +0200)]
phy: bcm-ns-usb3: always wait for idle after writing to the PHY reg
Move MDIO specific code to the writing helper function. This makes init
code a bit more generic and doesn't require it to track what happens
after every write.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
powerpc/debug: Add missing warn flag to WARN_ON's non-builtin path
When trapped on WARN_ON(), report_bug() is expected to return
BUG_TRAP_TYPE_WARN so the caller will increment NIP by 4 and continue.
The __builtin_constant_p() path of the PPC's WARN_ON()
calls (indirectly) __WARN_FLAGS() which has BUGFLAG_WARNING set,
however the other branch does not which makes report_bug() report a
bug rather than a warning.
Tony Lindgren [Mon, 12 Jun 2017 08:12:23 +0000 (01:12 -0700)]
phy: cpcap-usb: Fix missing return statement
Commit 8ae904e3c236 ("phy: cpcap-usb: Add CPCAP PMIC USB support")
is missing return statement as noted by Colin Ian King
<colin.king@canonical.com>. If the optional pins are not configured,
we just want to return early and not attempt to configure the pins.
Fixes: 8ae904e3c236 ("phy: cpcap-usb: Add CPCAP PMIC USB support") Reported-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Dave Airlie [Fri, 16 Jun 2017 00:01:04 +0000 (10:01 +1000)]
Merge tag 'drm-misc-fixes-2017-06-15' of git://anongit.freedesktop.org/git/drm-misc into drm-fixes
Driver Changes:
- dw-hdmi: Fix compilation error if REGMAP_MMIO not selected (Laurent)
- host1x: Fix incorrect return value (Christophe)
- tegra: Shore up idr API usage in tegra staging code (Dmitry)
- mgag200: Always use HiPri mode for G200e4v2 and limit max bandwidth (Mathieu)
- mxsfb: Ensure display can be lit up without bootloader initialization (Fabio)
Cc: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Cc: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Cc: Dmitry Osipenko <digetx@gmail.com> Cc: Mathieu Larouche <mathieu.larouche@matrox.com> Cc: Fabio Estevam <fabio.estevam@nxp.com>
* tag 'drm-misc-fixes-2017-06-15' of git://anongit.freedesktop.org/git/drm-misc:
drm: mxsfb_crtc: Reset the eLCDIF controller
drm/mgag200: Fix to always set HiPri for G200e4 V2
drm/tegra: Correct idr_alloc() minimum id
drm/tegra: Fix lockup on a use of staging API
gpu: host1x: Fix error handling
drm: dw-hdmi: Fix compilation breakage by selecting REGMAP_MMIO
Dave Airlie [Fri, 16 Jun 2017 00:00:11 +0000 (10:00 +1000)]
Merge branch 'drm-fixes-4.12' of git://people.freedesktop.org/~agd5f/linux into drm-fixes
A few fixes for 4.12:
- fix a UVD regression on SI
- fix overflow in watermark calcs on large modes
* 'drm-fixes-4.12' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: Fix overflow of watermark calcs at > 4k resolutions.
drm/amdgpu: Fix overflow of watermark calcs at > 4k resolutions.
drm/radeon: fix "force the UVD DPB into VRAM as well"
Mathias Nyman [Thu, 15 Jun 2017 08:55:46 +0000 (11:55 +0300)]
xhci: handle transfer events without TRB pointer
Most transfer events have a TRB pointer indicating which TRB caused
the event.
In the case of streams, transfer events such as
USB Transaction error may have its TRB pointer set to zero.
driver won't know which stream or what TRB on that stream caused
the error, but it can issue a soft reset to recover the transfer.
A soft reset will clear the host side halt of the endpoint without
clearing Data toggle or sequence number, and let the transfer
continue from where it halted.
see xhci section 4.12 streams and 4.6.8.2 soft retry.
USB Transaction errors with a zero TRB pointer are seen with
UAS usb devices.
Mathias Nyman [Thu, 15 Jun 2017 08:55:45 +0000 (11:55 +0300)]
xhci: support calling cleanup_halted_endpoint with soft retry
Add soft reset support to cleanup_halted_endpoint().
using soft reset will prevent it from setting a new dequeue pointer to
start the transfer from. Let it continue where it halted.
Mathias Nyman [Thu, 15 Jun 2017 08:55:44 +0000 (11:55 +0300)]
xhci: Add support for endpoint soft reset
xhci supports soft retry recovery when the host halted the host side of an
endopint but the connected USB device is not aware of the halt.
In this case xhci needs to issue a reset endopint command with a TSP
(Transfer State Preserve) flag set which preserves the Data toggle
and Sequence number of the endpoint.
This feature is needed to handle a few special transfer event types
such as USB Transaction error that don't always point to a causing TRB.
Mathias Nyman [Thu, 15 Jun 2017 08:55:42 +0000 (11:55 +0300)]
xhci: remove endpoint ring cache
Anurag Kumar Vulisha reported several issues with xhci endpoint
ring caching.
31 Rings are cached per device before a ring is freed.
These cached rings are not used as default if a new ring is needed.
They are only used if the driver fails to allocate memory for a ring.
The current ring cache is more a reason to why we run out memory than a
help when we actually do so.
Anurag Kumar Vulisha tried to use cached rings as a first option and
found new issues with cached ring initialization.
Cached rings were first zeroed and then manually reinitialized with link
trbs etc, but forgetting to set some important bits like cycle toggle bit.
Remove the ring cache completely as it's a faulty premature optimization
eating memory
Mathias Nyman [Thu, 15 Jun 2017 08:55:41 +0000 (11:55 +0300)]
usb: Avoid unnecessary LPM enabling and disabling during suspend and resume
The original motivation for disabling/enabling Link PM at device
suspend/resume was to force link state to go via U0 before suspend sets
the link state to U3. Going directly from U2 to U3 is not allowed.
Disabling LPM will forced the link state to U0, but will send a lot of
Set port feature requests for evert suspend and resume.
This is not needed as Hub hardware will take care of going via U0
when a U2 -> U3 transition is requested [1]
[1] USB 3.1 specification section 10.16.2.10 Set Port Feature:
"If the value is 3, then host software wants to selectively suspend the
device connected to this port. The hub shall transition the link to U3
from any of the other U states using allowed link state transitions.
If the port is not already in the U0 state, then it shall transition the
port to the U0 state and then initiate the transition to U3.
While this state is active, the hub does not propagate downstream-directed
traffic to this port, but the hub will respond to resume signaling from the
port"
Alan Stern [Tue, 13 Jun 2017 19:23:42 +0000 (15:23 -0400)]
USB: gadgetfs, dummy-hcd, net2280: fix locking for callbacks
Using the syzkaller kernel fuzzer, Andrey Konovalov generated the
following error in gadgetfs:
> BUG: KASAN: use-after-free in __lock_acquire+0x3069/0x3690
> kernel/locking/lockdep.c:3246
> Read of size 8 at addr ffff88003a2bdaf8 by task kworker/3:1/903
>
> CPU: 3 PID: 903 Comm: kworker/3:1 Not tainted 4.12.0-rc4+ #35
> Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
> Workqueue: usb_hub_wq hub_event
> Call Trace:
> __dump_stack lib/dump_stack.c:16 [inline]
> dump_stack+0x292/0x395 lib/dump_stack.c:52
> print_address_description+0x78/0x280 mm/kasan/report.c:252
> kasan_report_error mm/kasan/report.c:351 [inline]
> kasan_report+0x230/0x340 mm/kasan/report.c:408
> __asan_report_load8_noabort+0x19/0x20 mm/kasan/report.c:429
> __lock_acquire+0x3069/0x3690 kernel/locking/lockdep.c:3246
> lock_acquire+0x22d/0x560 kernel/locking/lockdep.c:3855
> __raw_spin_lock include/linux/spinlock_api_smp.h:142 [inline]
> _raw_spin_lock+0x2f/0x40 kernel/locking/spinlock.c:151
> spin_lock include/linux/spinlock.h:299 [inline]
> gadgetfs_suspend+0x89/0x130 drivers/usb/gadget/legacy/inode.c:1682
> set_link_state+0x88e/0xae0 drivers/usb/gadget/udc/dummy_hcd.c:455
> dummy_hub_control+0xd7e/0x1fb0 drivers/usb/gadget/udc/dummy_hcd.c:2074
> rh_call_control drivers/usb/core/hcd.c:689 [inline]
> rh_urb_enqueue drivers/usb/core/hcd.c:846 [inline]
> usb_hcd_submit_urb+0x92f/0x20b0 drivers/usb/core/hcd.c:1650
> usb_submit_urb+0x8b2/0x12c0 drivers/usb/core/urb.c:542
> usb_start_wait_urb+0x148/0x5b0 drivers/usb/core/message.c:56
> usb_internal_control_msg drivers/usb/core/message.c:100 [inline]
> usb_control_msg+0x341/0x4d0 drivers/usb/core/message.c:151
> usb_clear_port_feature+0x74/0xa0 drivers/usb/core/hub.c:412
> hub_port_disable+0x123/0x510 drivers/usb/core/hub.c:4177
> hub_port_init+0x1ed/0x2940 drivers/usb/core/hub.c:4648
> hub_port_connect drivers/usb/core/hub.c:4826 [inline]
> hub_port_connect_change drivers/usb/core/hub.c:4999 [inline]
> port_event drivers/usb/core/hub.c:5105 [inline]
> hub_event+0x1ae1/0x3d40 drivers/usb/core/hub.c:5185
> process_one_work+0xc08/0x1bd0 kernel/workqueue.c:2097
> process_scheduled_works kernel/workqueue.c:2157 [inline]
> worker_thread+0xb2b/0x1860 kernel/workqueue.c:2233
> kthread+0x363/0x440 kernel/kthread.c:231
> ret_from_fork+0x2a/0x40 arch/x86/entry/entry_64.S:424
>
> Allocated by task 9958:
> save_stack_trace+0x1b/0x20 arch/x86/kernel/stacktrace.c:59
> save_stack+0x43/0xd0 mm/kasan/kasan.c:513
> set_track mm/kasan/kasan.c:525 [inline]
> kasan_kmalloc+0xad/0xe0 mm/kasan/kasan.c:617
> kmem_cache_alloc_trace+0x87/0x280 mm/slub.c:2745
> kmalloc include/linux/slab.h:492 [inline]
> kzalloc include/linux/slab.h:665 [inline]
> dev_new drivers/usb/gadget/legacy/inode.c:170 [inline]
> gadgetfs_fill_super+0x24f/0x540 drivers/usb/gadget/legacy/inode.c:1993
> mount_single+0xf6/0x160 fs/super.c:1192
> gadgetfs_mount+0x31/0x40 drivers/usb/gadget/legacy/inode.c:2019
> mount_fs+0x9c/0x2d0 fs/super.c:1223
> vfs_kern_mount.part.25+0xcb/0x490 fs/namespace.c:976
> vfs_kern_mount fs/namespace.c:2509 [inline]
> do_new_mount fs/namespace.c:2512 [inline]
> do_mount+0x41b/0x2d90 fs/namespace.c:2834
> SYSC_mount fs/namespace.c:3050 [inline]
> SyS_mount+0xb0/0x120 fs/namespace.c:3027
> entry_SYSCALL_64_fastpath+0x1f/0xbe
>
> Freed by task 9960:
> save_stack_trace+0x1b/0x20 arch/x86/kernel/stacktrace.c:59
> save_stack+0x43/0xd0 mm/kasan/kasan.c:513
> set_track mm/kasan/kasan.c:525 [inline]
> kasan_slab_free+0x72/0xc0 mm/kasan/kasan.c:590
> slab_free_hook mm/slub.c:1357 [inline]
> slab_free_freelist_hook mm/slub.c:1379 [inline]
> slab_free mm/slub.c:2961 [inline]
> kfree+0xed/0x2b0 mm/slub.c:3882
> put_dev+0x124/0x160 drivers/usb/gadget/legacy/inode.c:163
> gadgetfs_kill_sb+0x33/0x60 drivers/usb/gadget/legacy/inode.c:2027
> deactivate_locked_super+0x8d/0xd0 fs/super.c:309
> deactivate_super+0x21e/0x310 fs/super.c:340
> cleanup_mnt+0xb7/0x150 fs/namespace.c:1112
> __cleanup_mnt+0x1b/0x20 fs/namespace.c:1119
> task_work_run+0x1a0/0x280 kernel/task_work.c:116
> exit_task_work include/linux/task_work.h:21 [inline]
> do_exit+0x18a8/0x2820 kernel/exit.c:878
> do_group_exit+0x14e/0x420 kernel/exit.c:982
> get_signal+0x784/0x1780 kernel/signal.c:2318
> do_signal+0xd7/0x2130 arch/x86/kernel/signal.c:808
> exit_to_usermode_loop+0x1ac/0x240 arch/x86/entry/common.c:157
> prepare_exit_to_usermode arch/x86/entry/common.c:194 [inline]
> syscall_return_slowpath+0x3ba/0x410 arch/x86/entry/common.c:263
> entry_SYSCALL_64_fastpath+0xbc/0xbe
>
> The buggy address belongs to the object at ffff88003a2bdae0
> which belongs to the cache kmalloc-1024 of size 1024
> The buggy address is located 24 bytes inside of
> 1024-byte region [ffff88003a2bdae0, ffff88003a2bdee0)
> The buggy address belongs to the page:
> page:ffffea0000e8ae00 count:1 mapcount:0 mapping: (null)
> index:0x0 compound_mapcount: 0
> flags: 0x100000000008100(slab|head)
> raw: 0100000000008100000000000000000000000000000000000000000100170017
> raw: ffffea0000ed3020ffffea0000f5f820ffff88003e80efc00000000000000000
> page dumped because: kasan: bad access detected
>
> Memory state around the buggy address:
> ffff88003a2bd980: fb fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
> ffff88003a2bda00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
> >ffff88003a2bda80: fc fc fc fc fc fc fc fc fc fc fc fc fb fb fb fb
> ^
> ffff88003a2bdb00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
> ffff88003a2bdb80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
> ==================================================================
What this means is that the gadgetfs_suspend() routine was trying to
access dev->lock after it had been deallocated. The root cause is a
race in the dummy_hcd driver; the dummy_udc_stop() routine can race
with the rest of the driver because it contains no locking. And even
when proper locking is added, it can still race with the
set_link_state() function because that function incorrectly drops the
private spinlock before invoking any gadget driver callbacks.
The result of this race, as seen above, is that set_link_state() can
invoke a callback in gadgetfs even after gadgetfs has been unbound
from dummy_hcd's UDC and its private data structures have been
deallocated.
include/linux/usb/gadget.h documents that the ->reset, ->disconnect,
->suspend, and ->resume callbacks may be invoked in interrupt context.
In general this is necessary, to prevent races with gadget driver
removal. This patch fixes dummy_hcd to retain the spinlock across
these calls, and it adds a spinlock acquisition to dummy_udc_stop() to
prevent the race.
The net2280 driver makes the same mistake of dropping the private
spinlock for its ->disconnect and ->reset callback invocations. The
patch fixes it too.
Lastly, since gadgetfs_suspend() may be invoked in interrupt context,
it cannot assume that interrupts are enabled when it runs. It must
use spin_lock_irqsave() instead of spin_lock_irq(). The patch fixes
that bug as well.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-and-tested-by: Andrey Konovalov <andreyknvl@google.com> CC: <stable@vger.kernel.org> Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fabio Estevam [Fri, 5 May 2017 18:01:41 +0000 (15:01 -0300)]
drm: mxsfb_crtc: Reset the eLCDIF controller
According to the eLCDIF initialization steps listed in the MX6SX
Reference Manual the eLCDIF block reset is mandatory.
Without performing the eLCDIF reset the display shows garbage content
when the kernel boots.
In earlier tests this issue has not been observed because the bootloader
was previously showing a splash screen and the bootloader display driver
does properly implement the eLCDIF reset.
Add the eLCDIF reset to the driver, so that it can operate correctly
independently of the bootloader.
This happen When run "i2cdetect -y 0" detect SMBus iSMT adapter.
After finished I2C block read/write, when unmap the data buffer,
a wrong device address was pass to dma_unmap_single().
To fix this, give dma_unmap_single() the "dev" parameter, just like
what dma_map_single() does, then unmap can find the right devices.
Fixes: 13f35ac14cd0 ("i2c: Adding support for Intel iSMT SMBus 2.0 host controller") Signed-off-by: Liwei Song <liwei.song@windriver.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Wolfram Sang [Sun, 28 May 2017 07:52:17 +0000 (09:52 +0200)]
i2c: rcar: use correct length when unmapping DMA
Because we need to transfer some bytes with PIO, the msg length is not
the length of the DMA buffer. Use the correct value which we used when
doing the mapping.
Architecturally we should apply a 0x400 offset for these. Not doing
it will break future HW implementations.
The offset of 0 is supposed to remain for "triggers" though not all
sources support both trigger and store EOI, and in P9 specifically,
some sources will treat 0 as a store EOI. But future chips will not.
So this makes us use the properly architected offset which should work
always.
Fixes: 243e25112d06 ("powerpc/xive: Native exploitation of the XIVE interrupt controller") Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Dmitry Osipenko [Wed, 14 Jun 2017 23:18:25 +0000 (02:18 +0300)]
drm/tegra: Correct idr_alloc() minimum id
The client ID 0 is reserved by the host1x/cdma to mark the timeout timer
work as already been scheduled and context ID is used as the clients one.
This fixes spurious CDMA timeouts.
Andy Lutomirski [Thu, 15 Jun 2017 11:46:00 +0000 (13:46 +0200)]
firmware: dmi_scan: Make dmi_walk and dmi_walk_early return real error codes
Currently they return -1 on error, which will confuse callers if
they try to interpret it as a normal negative error code.
Signed-off-by: Andy Lutomirski <luto@kernel.org> Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org> Signed-off-by: Jean Delvare <jdelvare@suse.de>
Jean Delvare [Thu, 15 Jun 2017 11:46:00 +0000 (13:46 +0200)]
firmware: dmi_scan: Look for SMBIOS 3 entry point first
Since version 3.0.0 of the SMBIOS specification, there can be
multiple entry points in memory, pointing to one or two DMI tables.
If both a 32-bit ("_SM_") entry point and a 64-bit ("_SM3_") entry
point are present, the specification requires that the latter points
to a table which is a super-set of the table pointed to by the
former. Therefore we should give preference to the 64-bit ("_SM3_")
entry point.
However, currently the code is picking the first valid entry point
it finds. Per specification, we should look for a 64-bit ("_SM3_")
entry point first, and if we can't find any, look for a 32-bit
("_SM_" or "_DMI_") entry point. Modify the code to do that.
Andrei Vagin [Fri, 9 Jun 2017 00:32:29 +0000 (17:32 -0700)]
fs: don't forget to put old mntns in mntns_install
Fixes: 4f757f3cbf54 ("make sure that mntns_install() doesn't end up with referral for root") Cc: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Andrei Vagin <avagin@openvz.org> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Al Viro [Sat, 3 Jun 2017 06:20:09 +0000 (07:20 +0100)]
Hang/soft lockup in d_invalidate with simultaneous calls
It's not hard to trigger a bunch of d_invalidate() on the same
dentry in parallel. They end up fighting each other - any
dentry picked for removal by one will be skipped by the rest
and we'll go for the next iteration through the entire
subtree, even if everything is being skipped. Morevoer, we
immediately go back to scanning the subtree. The only thing
we really need is to dissolve all mounts in the subtree and
as soon as we've nothing left to do, we can just unhash the
dentry and bugger off.
Paul Burton [Fri, 2 Jun 2017 19:02:08 +0000 (12:02 -0700)]
MIPS: .its targets depend on vmlinux
The .its targets require information about the kernel binary, such as
its entry point, which is extracted from the vmlinux ELF. We therefore
require that the ELF is built before the .its files are generated.
Declare this requirement in the Makefile such that make will ensure this
is always the case, otherwise in corner cases we can hit issues as the
.its is generated with an incorrect (either invalid or stale) entry
point.
Signed-off-by: Paul Burton <paul.burton@imgtec.com> Fixes: cf2a5e0bb4c6 ("MIPS: Support generating Flattened Image Trees (.itb)") Cc: linux-mips@linux-mips.org Cc: stable <stable@vger.kernel.org> # v4.9+
Patchwork: https://patchwork.linux-mips.org/patch/16179/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Paul Burton [Fri, 2 Jun 2017 18:35:01 +0000 (11:35 -0700)]
MIPS: Fix bnezc/jialc return address calculation
The code handling the pop76 opcode (ie. bnezc & jialc instructions) in
__compute_return_epc_for_insn() needs to set the value of $31 in the
jialc case, which is encoded with rs = 0. However its check to
differentiate bnezc (rs != 0) from jialc (rs = 0) was unfortunately
backwards, meaning that if we emulate a bnezc instruction we clobber $31
& if we emulate a jialc instruction it actually behaves like a jic
instruction.
Fix this by inverting the check of rs to match the way the instructions
are actually encoded.
Signed-off-by: Paul Burton <paul.burton@imgtec.com> Fixes: 28d6f93d201d ("MIPS: Emulate the new MIPS R6 BNEZC and JIALC instructions") Cc: stable <stable@vger.kernel.org> # v4.0+ Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16178/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
1) The netlink attribute passed in to dev_set_alias() is not
necessarily NULL terminated, don't use strlcpy() on it. From
Alexander Potapenko.
2) Fix implementation of atomics in arm64 bpf JIT, from Daniel
Borkmann.
3) Correct the release of netdevs and driver private data in certain
circumstances.
4) Sanitize netlink message length properly in decnet, from Mateusz
Jurczyk.
5) Don't leak kernel data in rtnl_fill_vfinfo() netlink blobs. From
Yuval Mintz.
6) Hash secret is never initialized in ipv6 ILA translation code, from
Arnd Bergmann. I guess those clang warnings about unused inline
functions are useful for something!
7) Fix endian selection in bpf_endian.h, from Daniel Borkmann.
8) Sanitize sockaddr length before dereferncing any fields in AF_UNIX
and CAIF. From Mateusz Jurczyk.
9) Fix timestamping for GMAC3 chips in stmmac driver, from Mario
Molitor.
10) Do not leak netdev on dev_alloc_name() errors in mac80211, from
Johannes Berg.
11) Fix locking in sctp_for_each_endpoint(), from Xin Long.
12) Fix wrong memset size on 32-bit in snmp6, from Christian Perle.
13) Fix use after free in ip_mc_clear_src(), from WANG Cong.
14) Fix regressions caused by ICMP rate limiting changes in 4.11, from
Jesper Dangaard Brouer.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (91 commits)
i40e: Fix a sleep-in-atomic bug
net: don't global ICMP rate limit packets originating from loopback
net/act_pedit: fix an error code
net: update undefined ->ndo_change_mtu() comment
net_sched: move tcf_lock down after gen_replace_estimator()
caif: Add sockaddr length check before accessing sa_family in connect handler
qed: fix dump of context data
qmi_wwan: new Telewell and Sierra device IDs
net: phy: Fix MDIO_THUNDER dependencies
netconsole: Remove duplicate "netconsole: " logging prefix
igmp: acquire pmc lock for ip_mc_clear_src()
r8152: give the device version
net: rps: fix uninitialized symbol warning
mac80211: don't send SMPS action frame in AP mode when not needed
mac80211/wpa: use constant time memory comparison for MACs
mac80211: set bss_info data before configuring the channel
mac80211: remove 5/10 MHz rate code from station MLME
mac80211: Fix incorrect condition when checking rx timestamp
mac80211: don't look at the PM bit of BAR frames
i40e: fix handling of HW ATR eviction
...
Linus Torvalds [Thu, 15 Jun 2017 08:51:19 +0000 (17:51 +0900)]
Merge tag 'acpi-4.12-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fixes from Rafael Wysocki:
"These revert an ACPICA commit from the 4.11 cycle that causes problems
to happen on some systems and add a protection against possible kernel
crashes due to table reference counter imbalance.
Specifics:
- Revert a 4.11 ACPICA change that made assumptions which are not
satisfied on some systems and caused the enumeration of resources
to fail on them (Rafael Wysocki).
- Add a mechanism to prevent tables from being unmapped prematurely
due to reference counter overflows (Lv Zheng)"
* tag 'acpi-4.12-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPICA: Tables: Mechanism to handle late stage acpi_get_table() imbalance
Revert "ACPICA: Disassembler: Enhance resource descriptor detection"
Linus Torvalds [Thu, 15 Jun 2017 08:47:46 +0000 (17:47 +0900)]
Merge tag 'pm-4.12-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These revert a recent cpufreq schedutil governor change that turned
out to be problematic and fix a few minor issues in cpufreq, cpuidle
and the Exynos devfreq drivers.
Specifics:
- Revert a recent cpufreq schedutil governor change that caused some
systems to behave undesirably (Rafael Wysocki).
- Fix a cpufreq conservative governor issue introduced during the
3.10 cycle that prevents it from working as expected in some
situations (Tomasz Wilczyński).
- Fix an error code path in the generic cpuidle driver for DT-based
systems (Christophe Jaillet).
- Fix three minor issues in devfreq drivers for Exynos (Arvind Yadav,
Krzysztof Kozlowski)"
* tag 'pm-4.12-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpuidle: dt: Add missing 'of_node_put()'
cpufreq: conservative: Allow down_threshold to take values from 1 to 10
Revert "cpufreq: schedutil: Reduce frequencies slower"
PM / devfreq: exynos-ppmu: Staticize event list
PM / devfreq: exynos-ppmu: Handle return value of clk_prepare_enable
PM / devfreq: exynos-nocp: Handle return value of clk_prepare_enable
Linus Torvalds [Thu, 15 Jun 2017 08:44:41 +0000 (17:44 +0900)]
Merge branch 'for-4.12/driver-matching-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
Pull HID fix from Jiri Kosina:
- ifdef-based bandaid for a long-standing issue with HID driver
matching, avoiding regressions in cases where specific driver is not
enabled in kernel .config, from Jiri Kosina
* 'for-4.12/driver-matching-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: let generic driver yield control iff specific driver has been enabled
projects / karo-tx-linux.git / log