The manual FIFO configuration was the first version to enable
the use of the FIFO in the codec.
It had served it's purpose as debugging aid, but the automatic
FIFO configuration is much safer to use.
The removal of the manual controls, and configuration makes
it easier to add new features for the codec later, since
the manual mode neded different ways to calculate, and
protect against misconfiguration.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
After coming back from suspend, the timeout waiting for Phoenix
chip to complete its power up sequence is not enough, which leaves
the codec cache value for some registers in an outdated state.
Increase the timeout value to wait for the power up sequence
to correclty complete.
Signed-off-by: Jorge Eduardo Candelaria <jorge.candelaria@ti.com> Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
ASoC: twl6040: Clear interrupt status at boot time
On Phoenix 1.1, the INTID register default value is an invalid
one, causing the interrupt handler to think the phoenix power on
sequence is ready before it actually finishes.
This causes some i2c errors when trying to configure twl.
Signed-off-by: Jorge Eduardo Candelaria <jorge.candelaria@ti.com> Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Peter Ujfalusi [Tue, 14 Dec 2010 11:45:29 +0000 (13:45 +0200)]
ASoC: TWL4030: Fix 24bit support
twl4030 series of codecs supports S32_LE with msbits=24.
Replace the S24_LE with S32_LE format, and add constraint
for 24msbit in case of 32 S32_LE format.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Olaya, Margarita [Sat, 11 Dec 2010 03:11:44 +0000 (21:11 -0600)]
ASoC: dapm: Add output driver widget
In some cases it was not possible to follow the appropiate power
ON/OFF sequence like in cases where the PGA needs to be enabled
before the driver and disabled before the PGA for pop reduction.
Add a widget to support output driver (speaker, haptic, vibra, etc)
drivers where power ON/OFF ordering is important.
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Jarkko Nikula [Fri, 10 Dec 2010 18:54:49 +0000 (20:54 +0200)]
ASoC: Fix build error caused by merging a fix for 2.6.37 into 2.6.38
Fix "ASoC: Fix bias power down of non-DAPM codec" for 3.6.37 will cause a
build error when merging into ASoC for-2.6.38. Fix the issue by doing a
change that commit ce6120c "ASoC: Decouple DAPM from CODECs" would do.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Jarkko Nikula [Fri, 10 Dec 2010 18:53:55 +0000 (20:53 +0200)]
ASoC: Fix bias power down of non-DAPM codec
Currently bias of non-DAPM codec will be powered down (standby/off) whenever
there is a stream stop. This is wrong in simultaneous playback/capture since
the bias is put down immediately after stopping the first stream.
Fix this by using the codec->active count when figuring out the needed bias
level after stream stop.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* wm8350, wm8753 and soc-core use custom code to cancel a delayed
work, execute it immediately if it was pending and wait for its
completion. This is equivalent to flush_delayed_work_sync(). Use
it instead.
Signed-off-by: Tejun Heo <tj@kernel.org> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Peter Ujfalusi [Fri, 10 Dec 2010 11:26:31 +0000 (13:26 +0200)]
ASoC: tlv320dac33: Power down digital parts, when not needed
If the following scenario has been followed:
1. Enable analog bypass
amixer sset 'Analog Left Bypass' on
amixer sset 'Analog Right Bypass' on
2. Start playback
aplay -fdat -d3 /dev/zero
After the playback stopped (3 sec), and the soc timeout (5 sec),
the digital parts of the codec will remain powered up.
This means that the DAI clocks are continue to run, the
oscillator remain operational, etc.
Use the SND_SOC_DAPM_POST_PMD widget to get notification
about the stopped stream, and power down the digital
part of the codec.
If the analog bypass is enabled, than the codec will remain in
BIAS_ON level, and things will work correctly.
In case, if the bypass is disabled, than the codec will
fall to BIAS_STANDBY than to BIAS_OFF level, as it used
to.
The digital part of DAC33 is initialized at every stream start
(DAPM_PRE:PRE_PMU event), so subsequent streams (within 5 sec)
will have working DAI.
When the codec is coming out from BIAS_OFF, the full power-up
sequence followed by the same DAPM_PRE widget event will power up
the digital part.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Mario Becroft [Fri, 3 Dec 2010 22:51:34 +0000 (11:51 +1300)]
ASoC: Optimise WM9081 FLL performance
Tune the FLL gain for optimal performance according to evaluation
results.
Signed-off-by: Mario Becroft <mb@gem.win.co.nz> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Changes to both I2S and PCM code:
- Rates list extended up to 96kHz, it's tested on EDB9302 and works for both capture and
playback.
Signed-off-by: Alexander Sverdlin <subaparts@yandex.ru> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
ASoC: fix deemphasis control in wm8904/55/60 codecs
Deemphasis control's .get callback should update control's value instead
of returning it - return value of callback function is used for indicating
error or success of operation.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Cc: stable@kernel.org
Peter Ujfalusi [Wed, 8 Dec 2010 13:12:56 +0000 (15:12 +0200)]
ASoC: tlv320dac33: Fix compillation error
Fix the compilation error introduced by patch:
ASoC: tlv320dac33: Avoid multiple soft power up
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Peter Ujfalusi [Wed, 8 Dec 2010 14:04:33 +0000 (16:04 +0200)]
ASoC: tlv320dac33: Move DAC LR power on to a supply widget
The power for the DACs need to be enabled, even when only
the analog bypass is in use with the codec, otherwise
the audio is going to be distorted.
Make sure that the DACs are powered all the time, when
there is audio activity.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Peter Ujfalusi [Wed, 8 Dec 2010 14:04:32 +0000 (16:04 +0200)]
ASoC: tlv320dac33: Rename outpup amplifier widget
Use better name for the widget, and remove the 'Power'
from it's name.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Uk Kim [Tue, 7 Dec 2010 13:58:40 +0000 (13:58 +0000)]
ASoC: Add ADC high pass filter support to WM8994
Signed-off-by: Uk Kim <w0806.kim@samsung.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Tue, 7 Dec 2010 17:14:56 +0000 (17:14 +0000)]
ASoC: Support WM8994 mono AIF configurations
The WM8994 supports mono signals - enable this in the driver. With DSP
mode an automatic data channel selector is available, activate this
when in mono mode.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
In case the codec driver did not provide a read/write function,
codec->driver->read|write will be NULL. Ensure that we use the one
specified in codec->read|write to avoid oopsing when we access
the debugfs entries. This is achieved by using snd_soc_read() and
snd_soc_write().
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Jassi Brar [Tue, 7 Dec 2010 10:23:07 +0000 (19:23 +0900)]
ASoC: WM8580: Debug BCLK and sample size
In case of SNDRV_PCM_FORMAT_S32_LE, we need to set WM8580_AIF_LENGTH_32,
rather than WM8580_AIF_LENGTH_24.
Also, the BCLK has to be 64fs, for sample size of 20, 24 and 32 bits.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Axel Lin [Tue, 7 Dec 2010 12:56:30 +0000 (20:56 +0800)]
ASoC: Fix resource leak if soc_register_ac97_dai_link failed
Properly free the resources in the case of soc_register_ac97_dai_link failure.
Signed-off-by: Axel Lin <axel.lin@gmail.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Linus Torvalds [Tue, 7 Dec 2010 04:08:25 +0000 (20:08 -0800)]
Merge branch 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jlbec/ocfs2
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jlbec/ocfs2:
ocfs2_connection_find() returns pointer to bad structure
ocfs2: char is not always signed
Ocfs2: Stop tracking a negative dentry after dentry_iput().
ocfs2: fix memory leak
fs/ocfs2/dlm: Use GFP_ATOMIC under spin_lock
Olof Johansson [Tue, 7 Dec 2010 01:36:32 +0000 (19:36 -0600)]
ARM: tegra: fix regression from addruart rewrite
Commit 0ea129300982 ("arm: return both physical and virtual addresses
from addruart") took out the test for MMU on/off but didn't switch the
ldr instructions to no longer be conditionals based on said test.
Fix that.
Signed-off-by: Olof Johansson <olof@lixom.net> Acked-by: Colin Cross <ccross@android.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Mon, 6 Dec 2010 23:51:14 +0000 (15:51 -0800)]
Merge branch 'pm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6
* 'pm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6:
PM / Hibernate: Fix memory corruption related to swap
PM / Hibernate: Use async I/O when reading compressed hibernation image
PM / Hibernate: Fix memory corruption related to swap
There is a problem that swap pages allocated before the creation of
a hibernation image can be released and used for storing the contents
of different memory pages while the image is being saved. Since the
kernel stored in the image doesn't know of that, it causes memory
corruption to occur after resume from hibernation, especially on
systems with relatively small RAM that need to swap often.
This issue can be addressed by keeping the GFP_IOFS bits clear
in gfp_allowed_mask during the entire hibernation, including the
saving of the image, until the system is finally turned off or
the hibernation is aborted. Unfortunately, for this purpose
it's necessary to rework the way in which the hibernate and
suspend code manipulates gfp_allowed_mask.
This change is based on an earlier patch from Hugh Dickins.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Reported-by: Ondrej Zary <linux@rainbow-software.org> Acked-by: Hugh Dickins <hughd@google.com> Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: stable@kernel.org
Linus Torvalds [Mon, 6 Dec 2010 22:49:51 +0000 (14:49 -0800)]
Merge master.kernel.org:/home/rmk/linux-2.6-arm
* master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: 6524/1: GIC irq desciptor bug fix
ARM: 6523/1: iop: ensure sched_clock() is notrace
ARM: 6456/1: Fix for building DEBUG with sa11xx_base.c as a module.
ARM: 6519/1: kuser: Fix incorrect cmpxchg syscall in kuser helpers
ARM: 6505/1: kprobes: Don't HAVE_KPROBES when CONFIG_THUMB2_KERNEL is selected
ARM: 6508/1: vexpress: Correct data alignment in headsmp.S for CONFIG_THUMB2_KERNEL
ARM: 6507/1: RealView: Correct data alignment in headsmp.S for CONFIG_THUMB2_KERNEL
ARM: 6504/1: Thumb-2: Fix long-distance conditional branches in head.S for Thumb-2.
ARM: 6503/1: Thumb-2: Restore sensible zImage header layout for CONFIG_THUMB2_KERNEL
ARM: 6502/1: Thumb-2: Fix CONFIG_THUMB2_KERNEL breakage in compressed/head.S
ARM: 6501/1: Thumb-2: Correct data alignment for CONFIG_THUMB2_KERNEL in mm/proc-v7.S
ARM: 6500/1: Thumb-2: Correct data alignment for CONFIG_THUMB2_KERNEL in kernel/head.S
ARM: 6499/1: Thumb-2: Correct data alignment for CONFIG_THUMB2_KERNEL in bootp/init.S
ARM: 6498/1: vfp: Correct data alignment for CONFIG_THUMB2_KERNEL
ARM: 6497/1: kexec: Correct data alignment for CONFIG_THUMB2_KERNEL
ARM: 6496/1: GIC: Do not try to register more then NR_IRQS interrupts
ARM: cns3xxx: Fix build with CONFIG_PCI=y
Bojan Smojver [Thu, 25 Nov 2010 22:41:39 +0000 (23:41 +0100)]
PM / Hibernate: Use async I/O when reading compressed hibernation image
This is a fix for reading LZO compressed image using async I/O.
Essentially, instead of having just one page into which we keep
reading blocks from swap, we allocate enough of them to cover the
largest compressed size and then let block I/O pick them all up. Once
we have them all (and here we wait), we decompress them, as usual.
Obviously, the very first block we still pick up synchronously,
because we need to know the size of the lot before we pick up the
rest.
Also fixed the copyright line, which I've forgotten before.
Signed-off-by: Bojan Smojver <bojan@rexursive.com> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
ASoC: soc-core: Remove useless inline function construct
There is no need to mark this function as inline. Inline functions
usually are small and concise functions that benefit from not needing
to set up a stack frame and undergo a call/ret sequence upon each
invocation.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
ASoC: soc-core: Replace use of strncpy() with strlcpy()
By using strncpy() if the source string does not have a null byte in the
first n bytes, then the destination string is not null-terminated.
This can be fixed in a two-step process by manually null-terminating the
array after the use of strncpy() or by using strlcpy().
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Jarkko Nikula [Mon, 6 Dec 2010 14:27:07 +0000 (16:27 +0200)]
ASoC: Merge common code in DAI link and auxiliary codec probing/removal
Commit 2eea392 "ASoC: Add support for optional auxiliary dailess codecs"
added much of code that can be shared with DAI link codec probing/removal.
Merge now this common code into new soc_probe_codec, soc_remove_codec and
soc_post_component_init functions.
Error prints in these functions are converted to use dev_err and to print
the error code.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Sun, 5 Dec 2010 12:22:46 +0000 (12:22 +0000)]
ASoC: Add trace events for jack detection
As jack detection can trigger DAPM and the latency in debouncing can create
confusing windows in operation provide some trace events which will hopefully
help in diagnostics. The soc-jack core traces all reports that it gets and
the resulting notifications to upper layers. An event for jack IRQs is also
provided for instrumentation of debounce, and used in the GPIO jack code.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Uk Kim [Sun, 5 Dec 2010 08:26:07 +0000 (17:26 +0900)]
ASoC: Fix swap of left and right channels for WM8993/4 speaker boost gain
SPKOUTL_BOOST start from third bit, SPKOUTLR_BOOST start from 0 bit.
Signed-off-by: Uk Kim <w0806.kim@samsung.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Cc: stable@kernel.org
Uk Kim [Sun, 5 Dec 2010 08:32:16 +0000 (17:32 +0900)]
ASoC: Fix off by one error in WM8994 EQ register bank size
Signed-off-by: Uk Kim <w0806.kim@samsung.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Cc: stable@kernel.org
Mark Brown [Sat, 4 Dec 2010 12:41:04 +0000 (12:41 +0000)]
ASoC: Add post-CODEC bias level callback for machine driver
Currently the machine driver can only do bias level configuration before
the CODEC bias level is brought up. This means that the machine cannot do
any configuration which depends on the CODEC bias level being maintained.
Provide a post-CODEC callback which allows the machine driver to do things
like enable the FLL on a CODEC which is brought down to BIAS_OFF when idle.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Chao Xie [Mon, 6 Dec 2010 06:01:10 +0000 (07:01 +0100)]
ARM: 6524/1: GIC irq desciptor bug fix
gic_set_cpu will directly use irq_desc[]. If CONFIG_SPARSE_IRQ is
enabled, there is no irq_desc[]. So we need use irq_to_desc(irq) to
get the descriptor for irq.
Signed-off-by: Chao Xie <chao.xie@marvell.com> Acked-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Linus Torvalds [Mon, 6 Dec 2010 00:41:13 +0000 (16:41 -0800)]
Merge branch 'rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild-2.6
* 'rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild-2.6:
initramfs: Really fix build break on symbol-prefixed archs
[media] Fix Kconfig errors due to two visible menus
i2c/algos: convert Kconfig to use the menu's `visible' keyword
media/video: convert Kconfig to use the menu's `visible' keyword
Revert "i2c: Fix Kconfig dependencies"
kconfig: regen parser
kconfig: add an option to determine a menu's visibility
Linus Torvalds [Mon, 6 Dec 2010 00:40:31 +0000 (16:40 -0800)]
Merge branch 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/kyle/parisc-2.6
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/kyle/parisc-2.6:
parisc: Fix GSC PS/2 driver name for keyboard and mouse
parisc: KittyHawk LCD fix
parisc: convert the rest of the irq handlers to simple/percpu
parisc: fix dino/gsc interrupts
parisc: remove redundant initialization in sigsegv path of sys_rt_sigreturn
Revert "vfs: show unreachable paths in getcwd and proc"
Because it caused a chroot ttyname regression in 2.6.36.
As of 2.6.36 ttyname does not work in a chroot. It has already been
reported that screen breaks, and for me this breaks an automated
distribution testsuite, that I need to preserve the ability to run the
existing binaries on for several more years. glibc 2.11.3 which has a
fix for this is not an option.
Prepend "(unreachable)" to path strings if the path is not reachable
from the current root.
Two places updated are
- the return string from getcwd()
- and symlinks under /proc/$PID.
Other uses of d_path() are left unchanged (we know that some old
software crashes if /proc/mounts is changed).
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
So remove the nice sounding, but ultimately ill advised change to how
/proc/fd symlinks work.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Guy Martin [Sat, 6 Nov 2010 16:24:29 +0000 (16:24 +0000)]
parisc: KittyHawk LCD fix
K class aka KittyHawk don't have LED support on their LCD. Installing
HP-UX confirmed this. The current led_wq fills the LCD with black
characters each time it runs.
The patch prevents the led_wq workqueue and its proc entry to be
created for KittyHawk machines.
It also increase min_cmd_delay as currently, one character out of two
is lost when a string is sent to the LCD.
Signed-off-by: Guy Martin <gmsoft@tuxicoman.be> Signed-off-by: Kyle McMartin <kyle@mcmartin.c>
James Bottomley [Fri, 3 Dec 2010 02:01:05 +0000 (02:01 +0000)]
parisc: convert the rest of the irq handlers to simple/percpu
The generic conversion eliminates the spurious no_ack and no_end
routines, converts all the cascaded handlers to handle_simple_irq() and
makes iosapic use a modified handle_percpu_irq() to become the same as
the CPU irq's. This isn't an essential change, but it eliminates the
mask/unmask overhead of handle_level_irq().
James Bottomley [Thu, 2 Dec 2010 23:36:47 +0000 (23:36 +0000)]
parisc: fix dino/gsc interrupts
The essential problem we're currently having is that dino (and gsc) is a
cascaded CPU interrupt. Under the old __do_IRQ() handler, our CPU
interrupts basically did an ack followed by an end. In the new scheme,
we replaced them with level handlers which do a mask, an ack and then an
unmask (but no end). Instead, with the renaming of end to eoi, we
actually want to call the percpu flow handlers, because they actually
have all the characteristics we want.
This patch does the conversion and gets my C360 booting again.
Signed-off-by: James Bottomley <James.Bottomley@suse.de> Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
Rabin Vincent [Sat, 4 Dec 2010 05:20:52 +0000 (06:20 +0100)]
ARM: 6523/1: iop: ensure sched_clock() is notrace
Include sched.h to ensure sched_clock() has the notrace
annotation, and mark any functions it calls as notrace
too.
Include sched.h to ensure sched_clock() has the notrace
annotation, and mark any functions it calls as notrace
too.
Acked-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Rabin Vincent <rabin@rab.in> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
ARM: 6456/1: Fix for building DEBUG with sa11xx_base.c as a module.
This patch fixes a compilation issue when compiling PCMCIA SA1100
support as a module with PCMCIA_DEBUG enabled. The symbol
soc_pcmcia_debug was not beeing exported.
ARM: pcmcia: Fix for building DEBUG with sa11xx_base.c as a module.
This patch fixes a compilation issue when compiling PCMCIA SA1100
support as a module with PCMCIA_DEBUG enabled. The symbol
soc_pcmcia_debug was not beeing exported.
Cc: <stable@kernel.org> Signed-off-by: Marcelo Roberto Jimenez <mroberto@cpti.cetuc.puc-rio.br> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Dave Martin [Wed, 1 Dec 2010 17:12:43 +0000 (18:12 +0100)]
ARM: 6519/1: kuser: Fix incorrect cmpxchg syscall in kuser helpers
The existing code invokes the syscall with rubbish in r7,
due to what looks like an incorrect literal load idiom.
Reviewed-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Dave Martin <dave.martin@linaro.org> Acked-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tero Roponen [Wed, 1 Dec 2010 18:04:20 +0000 (20:04 +0200)]
slub: Fix a crash during slabinfo -v
Commit f7cb1933621bce66a77f690776a16fe3ebbc4d58 ("SLUB: Pass active
and inactive redzone flags instead of boolean to debug functions")
missed two instances of check_object(). This caused a lot of warnings
during 'slabinfo -v' finally leading to a crash:
Linus Torvalds [Fri, 3 Dec 2010 19:30:57 +0000 (11:30 -0800)]
Merge branch '2.6.37-rc4-pvhvm-fixes' of git://xenbits.xen.org/people/sstabellini/linux-pvhvm
* '2.6.37-rc4-pvhvm-fixes' of git://xenbits.xen.org/people/sstabellini/linux-pvhvm:
xen: unplug the emulated devices at resume time
xen: fix save/restore for PV on HVM guests with pirq remapping
xen: resume the pv console for hvm guests too
xen: fix MSI setup and teardown for PV on HVM guests
xen: use PHYSDEVOP_get_free_pirq to implement find_unbound_pirq
Linus Torvalds [Fri, 3 Dec 2010 18:08:52 +0000 (10:08 -0800)]
Merge branches 'upstream/core' and 'upstream/bugfix' of git://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen
* 'upstream/core' of git://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen:
xen: allocate irq descs on any NUMA node
xen: prevent crashes with non-HIGHMEM 32-bit kernels with largeish memory
xen: use default_idle
xen: clean up "extra" memory handling some more
* 'upstream/bugfix' of git://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen:
xen: x86/32: perform initial startup on initial_page_table
xen: don't bother to stop other cpus on shutdown/reboot
Linus Torvalds [Fri, 3 Dec 2010 17:20:41 +0000 (09:20 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ASoC: omap: N810: Don't select CONFIG_OMAP_MUX but make it as dependency
ALSA: hda: Use "alienware" model quirk for another SSID
ASoC: WM8731: Fix incorrect mask for bypass path disable
s6105-ipcam: fix compilation
s6000-pcm: fix compilation
s6000-i2s: fix compilation
ASoC: Fix missing spin_unlock_irqrestore
ALSA: Fix SNDCTL_DSP_RESET ioctl for OSS emulation
ASoC: Add missing dev_set_drvdata in p1022_ds_probe
ASoC: Add missing dev_set_drvdata in mpc8610_hpcd_probe
ASoC: Remove unneeded !! operations while checking return value of nuc900_checkready
ASoC: Fix compile error for nuc900-pcm.c
ASoC: Fix prototype for nuc900_ac97_probe and nuc900_ac97_remove
ASoC: Fix compile error for nuc900-ac97.c
ALSA: hda: Use BIOS auto-parsing instead of existing model quirk for MEDION MD2
Linus Torvalds [Fri, 3 Dec 2010 17:19:54 +0000 (09:19 -0800)]
Merge branch 'sh-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6
* 'sh-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
sh: se/7724: Remove FSI/B of GPIO init code
sh: se/7724: Update clock framework of FSI clock to non-legacy
sh: Assume new page cache pages have dirty dcache lines.
sh: boards: mach-se: use IS_ERR() instead of NULL check
sh: Add div6_reparent_clks to clock framework for FSI
dma: shdma: add a MODULE_ALIAS() to allow module autoloading
Linus Torvalds [Fri, 3 Dec 2010 17:19:31 +0000 (09:19 -0800)]
Merge branch 'fbdev-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/fbdev-2.6
* 'fbdev-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/fbdev-2.6:
lxfb: Maintain video processor palette through suspend/resume
video: da8xx: Register IRQ as last thing in driver probing.
framebuffer: fix fbcmap.c kernel-doc warning
projects / linux-beck.git / log