Ben Skeggs [Fri, 16 Sep 2011 16:11:39 +0000 (02:11 +1000)]
drm/nv40/pm: convert to new pwm hooks, also fixing pwm type detection
A NV49 appeared a while back that was using the "nv41 style" pwm registers,
rather than the "nv40 style" ones my board is using. This disproves the
previous theory that the pwm controller choice is chipset-specific.
So, after looking at a bunch of vbios images it appears that the next viable
theory is that we should select the pwm controller to use based on the gpio
line the fan is tied to, just like we do on nv50.
Martin Peres [Mon, 15 Aug 2011 01:10:30 +0000 (11:10 +1000)]
drm/nouveau/pm: manual pwm fanspeed management for nv40+ boards
Exposes the following sysfs entries:
- fan0_input: read the rotational speed of the fan (poll a bit during 250ms)
- pwm0: set the pwm duty cycle
- pwm0_min/max: set the minimum/maximum pwm value
v2 (Ben Skeggs):
- nv50 pwm controller code removed in favour of other more complete code
- FAN_RPM -> FAN_SENSE
- merged FAN_SENSE readout into common code, not at all nv50-specific
- protected fanspeed changes with perflvl_wr
- formatting tidying
- added some comments where things are shaky
v3 (Martin Peres)
- ensure duty min/max from thermal table are sane
Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Martin Peres <martin.peres@ensi-bourges.fr>
Ville Syrjälä [Mon, 19 Dec 2011 22:33:24 +0000 (00:33 +0200)]
drm: Add drm_format_num_planes() utility function
This function returns the number of planes used by a specific pixel
format.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Rob Clark <rob.clark@linaro.org> Signed-off-by: Dave Airlie <airlied@redhat.com>
Rob Clark [Thu, 15 Dec 2011 20:53:24 +0000 (14:53 -0600)]
drm: call connector dpms fxn, when setting config
Call connector->funcs->dpms(DPMS_ON) rather than just setting
connector->dpms = DPMS_ON. This ensures that if the connector
has something to do to enable the output (rather than just using
drm_helper_connector_dpms helper directly), that this happens
at bootup. This solves an issue with connectors not getting
enabled from fbcon_init() when the driver is loaded.
Signed-off-by: Rob Clark <rob@ti.com> Reviewed-by: Adam Jackson <ajax@redhat.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie [Tue, 20 Dec 2011 11:44:30 +0000 (11:44 +0000)]
drm/radeon/kms: don't use 0 bpc for adjusting hdmi clock
If the bpc is set from the connector is 0, we then use it later to adjust
in a special case the HDMI pixel clock, however if the bpc is 0, we end up
passing a 0 pixel clock into the code.
I'm not sure if this is the correct answer or if we should avoid the HDMI
clock adjustment for 0 values.
This fixes a divide by 0 on my Llano system with a HDMI monitor and hdmi
audio enabled.
Reviewed-by: Alex Deucher <alexdeucher@gmail.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie [Tue, 20 Dec 2011 19:53:44 +0000 (19:53 +0000)]
Merge branch 'drm-radeon-next' of ../drm-radeon-next into drm-core-next
* 'drm-radeon-next' of ../drm-radeon-next:
drm/radeon: introduce a sub allocator and convert ib pool to it v4
drm/radeon/kms: add support for per-ring fence interrupts
drm/radeon/kms: add cayman specific fence_ring_emit
drm/radeon/kms: add some new ring params to better handle other ring types
drm/radeon: improve radeon_test_syncing function
drm/radeon: precompute fence cpu/gpu addr once v3
drm/radeon: move ring debugfs into radeon_ring.c
drm/radeon: rename struct radeon_cp to radeon_ring
drm/radeon: disable compute rings on cayman for now
drm/radeon: add radeon_fence_count_emited function
drm/radeon: make some asic pointers per ring
drm/radeon: Add radeon_test_syncing function v2
drm/radeon: make cp variable an array
drm/radeon: make ring rptr and wptr register offsets variable
drm/radeon: make all functions work with multiple rings.
drm/radeon/kms: add support for semaphores v3
drm/radeon/kms: add support for multiple fence queues v2
drm/radeon: fix a spelling mistake
drm/radeon: no need to check all relocs for duplicates
drm/radeon: fix debugfs handling v3
Jerome Glisse [Tue, 15 Nov 2011 16:48:34 +0000 (11:48 -0500)]
drm/radeon: introduce a sub allocator and convert ib pool to it v4
Somewhat specializaed sub-allocator designed to perform sub-allocation
for command buffer not only for current cs ioctl but for future command
submission ioctl as well. Patch also convert current ib pool to use
the sub allocator. Idea is that ib poll buffer can be share with other
command buffer submission not having 64K granularity.
v2 Harmonize pool handling and add suspend/resume callback to pin/unpin
sa bo (tested on rv280, rv370, r420, rv515, rv610, rv710, redwood, cayman,
rs480, rs690, rs880)
v3 Simplify allocator
v4 Fix radeon_ib_get error path to properly free fence
Signed-off-by: Jerome Glisse <jglisse@redhat.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Alex Deucher [Fri, 18 Nov 2011 01:13:28 +0000 (20:13 -0500)]
drm/radeon/kms: add support for per-ring fence interrupts
Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Christian König <deathsimple@vodafone.de> Signed-off-by: Dave Airlie <airlied@redhat.com>
Alex Deucher [Thu, 17 Nov 2011 19:57:50 +0000 (14:57 -0500)]
drm/radeon/kms: add cayman specific fence_ring_emit
cayman is wb only and doesn't have a VC.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Christian König <deathsimple@vodafone.de> Signed-off-by: Dave Airlie <airlied@redhat.com>
Alex Deucher [Thu, 17 Nov 2011 19:25:56 +0000 (14:25 -0500)]
drm/radeon/kms: add some new ring params to better handle other ring types
Some rptr/wptrs fields have different offsets and not all rings are pm4
so add a new nop field.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Christian König <deathsimple@vodafone.de> Signed-off-by: Dave Airlie <airlied@redhat.com>
Christian König [Thu, 17 Nov 2011 14:22:44 +0000 (15:22 +0100)]
drm/radeon: improve radeon_test_syncing function
Also test multiple waits on the same semaphore.
Signed-off-by: Christian König <deathsimple@vodafone.de> Reviewed-by: Jerome Glisse <jglisse@redhat.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Jerome Glisse [Sun, 20 Nov 2011 20:45:34 +0000 (20:45 +0000)]
drm/radeon: precompute fence cpu/gpu addr once v3
Add a start fence driver helper function which will be call
once for each ring and will compute cpu/gpu addr for fence
depending on wether to use wb buffer or scratch reg.
This patch replace initialize fence driver separately which
was broken in regard of GPU lockup. The fence list for created,
emited, signaled must be initialize once and only from the
asic init callback not from the startup call back which is
call from the gpu reset.
v2: With this in place we no longer need to know the number of
rings in fence_driver_init, also writing to the scratch reg
before knowing its offset is a bad idea.
v3: rebase on top of change to previous patch in the serie
Signed-off-by: Christian König <deathsimple@vodafone.de> Signed-off-by: Jerome Glisse <jglisse@redhat.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Christian König [Mon, 24 Oct 2011 15:08:44 +0000 (17:08 +0200)]
drm/radeon: move ring debugfs into radeon_ring.c
Those debugfs files aren't r600 specific, so they
shouldn't be in r600.c. Move them to radeon_ring.c
and also add functionality to dump CP1 & CP2 ring
informations.
Signed-off-by: Christian König <deathsimple@vodafone.de> Reviewed-by: Jerome Glisse <jglisse@redhat.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Christian König [Sun, 23 Oct 2011 10:56:27 +0000 (12:56 +0200)]
drm/radeon: rename struct radeon_cp to radeon_ring
That naming seems to make more sense, since we not
only want to run PM4 rings with it.
Signed-off-by: Christian König <deathsimple@vodafone.de> Reviewed-by: Jerome Glisse <jglisse@redhat.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Christian König [Thu, 20 Oct 2011 10:47:13 +0000 (12:47 +0200)]
drm/radeon: disable compute rings on cayman for now
Disable the additional compute rings on cayman
until their setup is fully implemented.
Signed-off-by: Christian König <deathsimple@vodafone.de> Reviewed-by: Jerome Glisse <jglisse@redhat.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Christian König [Thu, 20 Oct 2011 10:38:09 +0000 (12:38 +0200)]
drm/radeon: add radeon_fence_count_emited function
Split counting of emited fences out of power
management into a seperate function.
Signed-off-by: Christian König <deathsimple@vodafone.de> Reviewed-by: Jerome Glisse <jglisse@redhat.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Christian König [Wed, 19 Oct 2011 17:02:21 +0000 (19:02 +0200)]
drm/radeon: make some asic pointers per ring
Emitting fences, semaphores and ib works differently
on different ring, so its is easier to maintain
separate functions for each ring.
Signed-off-by: Christian König <deathsimple@vodafone.de> Reviewed-by: Jerome Glisse <jglisse@redhat.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Christian König [Tue, 27 Sep 2011 10:31:00 +0000 (12:31 +0200)]
drm/radeon: Add radeon_test_syncing function v2
Tests syncing between all rings by using
semaphores and fences.
v2: use radeon_testing as a bit flag rather than on/off switch
this allow to test for one thing at a time (bo_move or semaphore
test). It kind of break the usage if user wheren't using 1
for bo move test but as it's a test feature i believe it's ok.
Signed-off-by: Christian König <deathsimple@vodafone.de> Reviewed-by: Jerome Glisse <jglisse@redhat.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Christian König [Thu, 13 Oct 2011 11:19:22 +0000 (13:19 +0200)]
drm/radeon: make cp variable an array
Replace cp, cp1 and cp2 members with just an array
of radeon_cp structs.
Signed-off-by: Christian König <deathsimple@vodafone.de> Reviewed-by: Jerome Glisse <jglisse@redhat.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Christian König [Thu, 13 Oct 2011 10:48:45 +0000 (12:48 +0200)]
drm/radeon: make ring rptr and wptr register offsets variable
Every ring seems to have the concept of read and
write pointers. Make the register offset variable
so we can use the functions for different types of rings.
Signed-off-by: Christian König <deathsimple@vodafone.de> Reviewed-by: Jerome Glisse <jglisse@redhat.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Christian König [Fri, 23 Sep 2011 13:11:23 +0000 (15:11 +0200)]
drm/radeon: make all functions work with multiple rings.
Give all asic and radeon_ring_* functions a
radeon_cp parameter, so they know the ring to work with.
Signed-off-by: Christian König <deathsimple@vodafone.de> Reviewed-by: Jerome Glisse <jglisse@redhat.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Christian König [Thu, 15 Sep 2011 17:02:22 +0000 (19:02 +0200)]
drm/radeon/kms: add support for semaphores v3
They are used to sync between rings, while fences
sync between a ring and the cpu.
v2 Fix radeon_semaphore_driver_fini when no semaphore were
allocated.
v3 Initialize list early on to avoid issue in case or early
error
Signed-off-by: Christian König <deathsimple@vodafone.de> Signed-off-by: Jerome Glisse <jglisse@redhat.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Alex Deucher [Thu, 25 Aug 2011 17:39:48 +0000 (13:39 -0400)]
drm/radeon/kms: add support for multiple fence queues v2
For supporting multiple CP ring buffers, async DMA
engines and UVD. We still need a way to synchronize
between engines.
v2 initialize unused fence driver ring to avoid issue in
suspend/unload
Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Christian König <deathsimple@vodafone.de> Reviewed-by: Jerome Glisse <jglisse@redhat.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Christian König [Mon, 24 Oct 2011 13:05:29 +0000 (15:05 +0200)]
drm/radeon: fix a spelling mistake
Better fix it before this obvious typo spreads even more.
Signed-off-by: Christian König <deathsimple@vodafone.de> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: Jerome Glisse <jglisse@redhat.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Christian König [Mon, 24 Oct 2011 12:59:17 +0000 (14:59 +0200)]
drm/radeon: no need to check all relocs for duplicates
Only check the previously checked relocs for
duplicates. Also leaving the handle uninitialized
isn't such a good idea.
Signed-off-by: Christian König <deathsimple@vodafone.de> Reviewed-by: Jerome Glisse <jglisse@redhat.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Christian König [Mon, 24 Oct 2011 12:54:54 +0000 (14:54 +0200)]
drm/radeon: fix debugfs handling v3
Having registered debugfs files globally causes
the files to not show up on the second, third
etc.. card in the system.
v2: fix crash on module unloading
v3: fix space indentation
Signed-off-by: Christian König <deathsimple@vodafone.de> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: Jerome Glisse <jglisse@redhat.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Alan Cox [Tue, 20 Dec 2011 15:58:44 +0000 (15:58 +0000)]
gma500/oaktrail: panel display quality fix
The GCT setup was used on Moorestown. The Oaktrail version uses a normal PC
interface. That means we must also honour the dither info from the BIOS
data.
Signed-off-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Patrik Jakobsson [Mon, 19 Dec 2011 21:41:45 +0000 (21:41 +0000)]
gma500: SDVO DDC bus guessing isn't working so hardcode it instead
We currently don't have support for parsing SDVO mappings from BIOS so we're
guessing the bus switch parameter. This isn't working so hardcode it to a
configuration known to work on most poulsbo hardware.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com> Signed-off-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Patrik Jakobsson [Mon, 19 Dec 2011 21:41:22 +0000 (21:41 +0000)]
gma500: Convert Cedarview to work with new output handling
Replace psb_intel_output with psb_intel_encoder and psb_intel_connector.
Things will need to be cleaned up and tested so consider this an initial
patch for Cedarview.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com> Signed-off-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Patrik Jakobsson [Mon, 19 Dec 2011 21:41:10 +0000 (21:41 +0000)]
gma500: Replace SDVO code with slightly modified version from i915
Our current SDVO implementation is not working properly, so replace it with
a modified version of the i915. Further testing and debugging is needed to make
sure we can handle the different SDVO setups and wiring.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com> Signed-off-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Patrik Jakobsson [Mon, 19 Dec 2011 21:40:45 +0000 (21:40 +0000)]
gma500: Convert PSB LVDS to new output handling
LVDS for PSB now uses psb_intel_encoder and psb_intel_connectors instead of
psb_intel_output. i2c_bus and ddc_bus are moved to lvds_priv. There was also a
pointer to mode_dev (for no obvious reason) that we now get directly from
dev_priv.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com> Signed-off-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Patrik Jakobsson [Mon, 19 Dec 2011 21:39:53 +0000 (21:39 +0000)]
gma500: Initial support for our encoder and connector structs
First step towards adding i915 alike encoder and connector abstractions. This
will make life easier when adding i915 output code into our driver. It also
removes the old psb_intel_output struct.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com> Signed-off-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Ville Syrjälä [Mon, 19 Dec 2011 22:06:49 +0000 (00:06 +0200)]
drm: Replace pitch with pitches[] in drm_framebuffer
Otherwise each driver would need to keep the information inside
their own framebuffer object structure. Also add offsets[]. BOs
on the other hand are driver specific, so those can be kept in
driver specific structures.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
drm/intel: Fix initialization if startup happens in interlaced mode [v2]
My EFI BIOS starts the graphics card up in my projector's preferred EDID
mode, 1080@60i. The Intel driver does not clear all the interlaced bits.
This patch introduces a new PIPECONF_INTERLACE_MASK define and uses it
to restore progressive mode.
Signed-of-by: Christian Schmidt <schmidt@digadd.de> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Dave Airlie <airlied@redhat.com>
Fix wrong assumptions in cea_for_each_detailed_block v2
The current logic misunderstands the spec about CEA 18byte descriptors.
First, the spec doesn't state "detailed timing descriptors" but "18 byte
descriptors", so any data record could be stored, mixed timings and
other data, just as in the standard EDID.
Second, the lower four bit of byte 3 of the CEA record do not contain
the number of descriptors, but "the total number of DTDs defining native
formats in the whole EDID [...], starting with the first DTD in the DTD
list (which starts in the base EDID block)." A device can of course
support non-native formats.
As such the number can't be used to determine n, and the existing code
will filter non-timing 18byte descriptors anyway.
Signed-off-by: Christian Schmidt <schmidt@digadd.de> Reviewed-by: Adam Jackson <ajax@redhat.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
TFT/plasma televisions and projectors have become commonplace, and so
has the use of PCs to drive them. Add the video modes specified by an
EDID's CEA extension to the mode database for a connector.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc32: Be less strict in matching %lo part of relocation.
sbus: convert drivers/sbus/char/* to use module_platform_driver()
bbc_i2c: Remove unneeded err variable
sparc: Use kmemdup rather than duplicating its implementation
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
ipv6: Check dest prefix length on original route not copied one in rt6_alloc_cow().
sch_gred: should not use GFP_KERNEL while holding a spinlock
ipip, sit: copy parms.name after register_netdevice
ipv6: Fix for adding multicast route for loopback device automatically.
ssb: fix init regression with SoCs
rtl8192{ce,cu,de,se}: avoid problems because of possible ERFOFF -> ERFSLEEP transition
mac80211: fix another race in aggregation start
fsl_pq_mdio: Clean up tbi address configuration
ppp: fix pptp double release_sock in pptp_bind()
net/fec: fix the use of pdev->id
ath9k: fix check for antenna diversity support
batman-adv: delete global entry in case of roaming
batman-adv: in case of roaming mark the client with TT_CLIENT_ROAM
Bluetooth: Correct version check in hci_setup
btusb: fix a memory leak in btusb_send_frame()
Bluetooth: bnep: Fix module reference
Bluetooth: cmtp: Fix module reference
Bluetooth: btmrvl: support Marvell Bluetooth device SD8797
Linus Torvalds [Fri, 16 Dec 2011 20:15:50 +0000 (12:15 -0800)]
Merge branches 'for-linus' and 'for-linus-3.2' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: unplug every once and a while
Btrfs: deal with NULL srv_rsv in the delalloc inode reservation code
Btrfs: only set cache_generation if we setup the block group
Btrfs: don't panic if orphan item already exists
Btrfs: fix leaked space in truncate
Btrfs: fix how we do delalloc reservations and how we free reservations on error
Btrfs: deal with enospc from dirtying inodes properly
Btrfs: fix num_workers_starting bug and other bugs in async thread
BTRFS: Establish i_ops before calling d_instantiate
Btrfs: add a cond_resched() into the worker loop
Btrfs: fix ctime update of on-disk inode
btrfs: keep orphans for subvolume deletion
Btrfs: fix inaccurate available space on raid0 profile
Btrfs: fix wrong disk space information of the files
Btrfs: fix wrong i_size when truncating a file to a larger size
Btrfs: fix btrfs_end_bio to deal with write errors to a single mirror
* 'for-linus-3.2' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
btrfs: lower the dirty balance poll interval
Linus Torvalds [Fri, 16 Dec 2011 19:27:56 +0000 (11:27 -0800)]
Merge branch 'drm-intel-fixes' of git://people.freedesktop.org/~keithp/linux
* 'drm-intel-fixes' of git://people.freedesktop.org/~keithp/linux:
drm/i915/dp: Dither down to 6bpc if it makes the mode fit
drm/i915: enable semaphores on per-device defaults
drm/i915: don't set unpin_work if vblank_get fails
drm/i915: By default, enable RC6 on IVB and SNB when reasonable
iommu: Export intel_iommu_enabled to signal when iommu is in use
drm/i915/sdvo: Include LVDS panels for the IS_DIGITAL check
drm/i915: prevent division by zero when asking for chipset power
drm/i915: add PCH info to i915_capabilities
drm/i915: set the right SDVO transcoder for CPT
drm/i915: no-lvds quirk for ASUS AT5NM10T-I
drm/i915: Treat pre-gen4 backlight duty cycle value consistently
drm/i915: Hook up Ivybridge eDP
drm/i915: add multi-threaded forcewake support
Linus Torvalds [Fri, 16 Dec 2011 19:14:42 +0000 (11:14 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: HDA: Use LPIB Position fix for Intel SCH Poulsbo
ALSA: hda: fix mute led polarity for HP laptops with buggy BIOS
ALSA: HDA: Set position fix to LPIB for an Atom/Poulsbo based device
ASoC: Fix hx4700 error handling to free gpios if snd_soc_register_card fails
ASoC: WM8958: correctly show firmware magic on mismatch
ASoC: mxs: Add appropriate MODULE_ALIAS()
ASoC: mxs: Add missing MODULE_LICENSE("GPL")
ASoC: Fix WM8996 24.576MHz clock operation
ASoC: Include linux/module.h for smdk2443_wm9710
ASoC: Fix a typo in jive_wm8750
ASoC: Fix build dependency for SND_SOC_JZ4740_CODEC
ASoC: Include linux/io.h for jz4740 codec
Linus Torvalds [Fri, 16 Dec 2011 19:13:49 +0000 (11:13 -0800)]
Merge branch 'gpio/merge' of git://git.secretlab.ca/git/linux-2.6
* 'gpio/merge' of git://git.secretlab.ca/git/linux-2.6:
gpio: Fix DA9052 GPIO build errors.
gpio: mpc8xxx: don't allow input-only pins to be output for MPC5121
gpio-ml-ioh: Add the irq_disable/irq_enable hooks for ml-ioh irq chip
gpio-ml-ioh: fix a bug in the interrupt handler
gpio: pl061: drop extra check for NULL platform_data
Linus Torvalds [Fri, 16 Dec 2011 18:07:50 +0000 (10:07 -0800)]
Merge branch 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: OMAP: rx51: fix USB
ARM: OMAP: mcbsp: Fix possible memory corruption
arm/imx: fix power button on imx51 babbage board
ARM: imx: fix cpufreq build errors
ARM: mx5: add __initconst for fec pdata
MXC PWM: should active during DOZE/WAIT/DBG mode
ARM: EXYNOS: Fix build error without CONFIG_LOCAL_TIMERS
ARM: EXYNOS: Fix for stall in case of cpu hotplug or sleep
ARM: S5PV210: Set 1000ns as PWM backlight period on SMDKV210
ARM: SAMSUNG: remove duplicated header include
Wu Fengguang [Fri, 16 Dec 2011 17:32:57 +0000 (12:32 -0500)]
btrfs: lower the dirty balance poll interval
Tests show that the original large intervals can easily make the dirty
limit exceeded on 100 concurrent dd's. So adapt to as large as the
next check point selected by the dirty throttling algorithm.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com> Signed-off-by: Chris Mason <chris.mason@oracle.com>
v2: Rebased to current code, resulting in the fix applying to EDP panels as
well. Also changed from spatio-temporal to just spatial dithering on
pre-ironlake, to be conssitent (and less visual flicker)
Signed-off-by: Adam Jackson <ajax@redhat.com> Signed-off-by: Eric Anholt <eric@anholt.net> Tested-by: Eric Anholt <eric@anholt.net> Tested-by: Dirk Hohndel <hohndel@infradead.org> Signed-off-by: Keith Packard <keithp@keithp.com>
Eugeni Dodonov [Sat, 10 Dec 2011 01:16:37 +0000 (17:16 -0800)]
drm/i915: enable semaphores on per-device defaults
This adds a default setting for semaphores parameter, and enables
semaphores by default on IVB.
For now, as semaphores interaction with VTd causes random issues on
SNB, we do not enable them by default. But they can still be enabled
via the semaphores=1 kernel parameter.
v2: enables semaphores on SNB when IO remapping is disabled, with base
on Keith Packard patch.
CC: Daniel Vetter <daniel.vetter@ffwll.ch> CC: Ben Widawsky <ben@bwidawsk.net> CC: Keith Packard <keithp@keithp.com> CC: Jesse Barnes <jbarnes@virtuousgeek.org> CC: Chris Wilson <chris@chris-wilson.co.uk>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=42696
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=40564
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=41353
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=38862 Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com> Signed-off-by: Keith Packard <keithp@keithp.com>
Jesse Barnes [Mon, 29 Aug 2011 16:45:28 +0000 (09:45 -0700)]
drm/i915: don't set unpin_work if vblank_get fails
This fixes a race where we may try to finish a page flip and decrement
the refcount even if our vblank_get failed and we ended up with a
spurious flip pending interrupt.
Keith Packard [Thu, 17 Nov 2011 06:24:52 +0000 (22:24 -0800)]
drm/i915: By default, enable RC6 on IVB and SNB when reasonable
RC6 should always work on IVB, and should work on SNB whenever IO
remapping is disabled. RC6 never works on Ironlake. Make the default
value for the parameter follow these guidelines. Setting the value
to either 0 or 1 will force the specified behavior.
Signed-off-by: Keith Packard <keithp@keithp.com> Reviewed-by: Kenneth Graunke <kenneth@whitecape.org> Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=38567 Cc: Ted Phelps <phelps@gnusto.com> Cc: Peter <pab1612@gmail.com> Cc: Lukas Hejtmanek <xhejtman@fi.muni.cz> Cc: Andrew Lutomirski <luto@mit.edu>
Eugeni Dodonov [Wed, 23 Nov 2011 18:42:14 +0000 (16:42 -0200)]
iommu: Export intel_iommu_enabled to signal when iommu is in use
In i915 driver, we do not enable either rc6 or semaphores on SNB when dmar
is enabled. The new 'intel_iommu_enabled' variable signals when the
iommu code is in operation.
Cc: Ted Phelps <phelps@gnusto.com> Cc: Peter <pab1612@gmail.com> Cc: Lukas Hejtmanek <xhejtman@fi.muni.cz> Cc: Andrew Lutomirski <luto@mit.edu> CC: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Eugeni Dodonov <eugeni.dodonov@intel.com> Signed-off-by: Keith Packard <keithp@keithp.com>
Chris Wilson [Mon, 20 Jun 2011 13:45:50 +0000 (14:45 +0100)]
drm/i915/sdvo: Include LVDS panels for the IS_DIGITAL check
We were checking whether the supplied edid matched the connector it was
read from. We do this in case a DDC read returns an EDID for another
device on a multifunction or otherwise interesting card. However, we
failed to include LVDS as a digital device and so rejecting an otherwise
valid EDID.
Fixes the detection of the secondary SDVO LVDS panel on the Libretto
W105.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: Adam Jackson <ajax@redhat.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=39216 Signed-off-by: Keith Packard <keithp@keithp.com>
Eugeni Dodonov [Thu, 10 Nov 2011 15:55:15 +0000 (13:55 -0200)]
drm/i915: prevent division by zero when asking for chipset power
This prevents an in-kernel division by zero which happens when we are
asking for i915_chipset_val too quickly, or within a race condition
between the power monitoring thread and userspace accesses via debugfs.
The issue can be reproduced easily via the following command:
while ``; do cat /sys/kernel/debug/dri/0/i915_emon_status; done
This is particularly dangerous because it can be triggered by
a non-privileged user by just reading the debugfs entry.
This issue was also found independently by Konstantin Belousov
<kostikbel@gmail.com>, who proposed a similar patch.
Reported-by: Konstantin Belousov <kostikbel@gmail.com> Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org> Acked-by: Keith Packard <keithp@keithp.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: <stable@vger.kernel.org> Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com> Signed-off-by: Keith Packard <keithp@keithp.com>
Paulo Zanoni [Fri, 14 Oct 2011 21:17:41 +0000 (18:17 -0300)]
drm/i915: add PCH info to i915_capabilities
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Keith Packard <keithp@keithp.com>
Paulo Zanoni [Fri, 14 Oct 2011 21:16:22 +0000 (18:16 -0300)]
drm/i915: set the right SDVO transcoder for CPT
v2: add a CPT-specific macro, make code cleaner
v3: fix commit message
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=41272 Cc: stable@kernel.org Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Keith Packard <keithp@keithp.com>
Linus Torvalds [Thu, 15 Dec 2011 22:15:01 +0000 (14:15 -0800)]
Merge branch 'staging-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
* 'staging-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: r8712u: Add new USB ID
staging: tidspbridge: request dmtimer clocks on init
staging: tidspbridge: include module.h by default
Uwe Kleine-König [Thu, 15 Dec 2011 20:47:56 +0000 (21:47 +0100)]
ARM: unwinder: fix bisection to find origin in .idx section
The bisection implemented in unwind_find_origin() stopped to early. If
there is only a single entry left to check the original code just took
the end point as origin which might be wrong.
This was introduced in commit de66a979012d ("ARM: 7187/1: fix unwinding
for XIP kernels").
Tejun Heo [Thu, 15 Dec 2011 19:03:04 +0000 (20:03 +0100)]
block: don't kick empty queue in blk_drain_queue()
While probing, fd sets up queue, probes hardware and tears down the
queue if probing fails. In the process, blk_drain_queue() kicks the
queue which failed to finish initialization and fd is unhappy about
that.
Linus Torvalds [Thu, 15 Dec 2011 18:52:40 +0000 (10:52 -0800)]
Merge branch 'stable/for-linus-fixes-3.2' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
* 'stable/for-linus-fixes-3.2' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/swiotlb: Use page alignment for early buffer allocation.
xen: only limit memory map to maximum reservation for domain 0.