Bjorn Helgaas [Fri, 24 Feb 2012 03:19:00 +0000 (20:19 -0700)]
PCI: add generic pcibios_resource_to_bus()
This replaces the generic versions of pcibios_resource_to_bus() and
pcibios_bus_to_resource() in asm-generic/pci.h with versions that use
pci_resource_to_bus() and pci_bus_to_resource().
The replacements are equivalent except that they can apply host
bridge window offsets when the arch has supplied them by using
pci_add_resource_offset().
Each arch can convert to using pci_add_resource_offset() individually by
removing its device resource fixups from pcibios_fixup_bus() and supplying
ARCH_HAS_GENERIC_PCI_OFFSETS. ARCH_HAS_GENERIC_PCI_OFFSETS can be removed
after all have converted.
Bjorn Helgaas [Fri, 24 Feb 2012 03:19:00 +0000 (20:19 -0700)]
PCI: convert bus addresses to resource when reading BARs
Some PCI host bridges translate CPU addresses to PCI bus addresses.
Previously, we initialized pci_dev resources with PCI bus addresses,
then converted them to CPU addresses later in arch-specific code
(pcibios_fixup_resources()), which leaves a window of time where the
pci_dev resources are incorrect.
This patch adds support in the core for this address translation.
When the arch creates the root bus, it can supply the host bridge
address translation information, and the core can use it to set the
pci_dev resources correctly from the beginning.
This gives us a way to fix the problem that quirks that run between device
discovery and pcibios_fixup_resources() fail because they use pci_dev
resources that haven't been converted. The reference below is to one
such problem that affected ARM and ia64.
Note that this patch has no effect until an arch starts using
pci_add_resource_offset() with a non-zero offset: before that, all
all host bridge windows have a zero offset and pci_bus_to_resource()
copies the pci_bus_region directly to the struct resource.
Bjorn Helgaas [Fri, 24 Feb 2012 03:19:00 +0000 (20:19 -0700)]
PCI: add struct pci_host_bridge_window with CPU/bus address offset
Some PCI host bridges apply an address offset, so bus addresses on PCI are
different from CPU addresses. This patch adds a way for architectures to
tell the PCI core about this offset. For example:
Bjorn Helgaas [Fri, 24 Feb 2012 03:18:59 +0000 (20:18 -0700)]
PCI: don't publish new root bus until it's fully initialized
When pci_create_root_bus() adds the new struct pci_bus to the global
pci_root_buses list, the bus becomes visible to other parts of the
kernel, so it should be fully initialized.
This patch delays adding the bus to the pci_root_buses list until after
all the struct pci_bus initialization is finished.
Bjorn Helgaas [Fri, 24 Feb 2012 03:18:58 +0000 (20:18 -0700)]
powerpc/PCI: replace pci_probe_only with pci_flags
We already use pci_flags, so this just sets pci_flags directly and removes
the intermediate step of figuring out pci_probe_only, then using it to set
pci_flags.
The PCI core provides a pci_flags definition (currently __weak), so drop
the powerpc definitions in favor of that.
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org> CC: linuxppc-dev@lists.ozlabs.org Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Bjorn Helgaas [Fri, 24 Feb 2012 03:18:58 +0000 (20:18 -0700)]
powerpc/PCI: make pci_probe_only default to 0
pci_probe_only is set on ppc64 to prevent resource re-allocation
by the core. It's meant to be used in very specific circumstances
such as when operating under a hypervisor that may prevent such
re-allocation.
Instead of default to 1, we make it default to 0 and explicitly
set it in the few cases where we need it.
This fixes FSL PCI which wants it clear among others.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
We never assign anything other than PCI_ASSIGN_ALL_BUSSES to pci_probe,
so just remove the indirection. If configurability is required in the
future, please use the pci_flags/PCI_REASSIGN_ALL_BUS functionality
as is done for powerpc.
Bjorn Helgaas [Fri, 24 Feb 2012 03:18:57 +0000 (20:18 -0700)]
mips/PCI: replace pci_probe_only with pci_flags
Some architectures (alpha, mips, powerpc) have an arch-specific
"pci_probe_only" flag. Others use PCI_PROBE_ONLY in pci_flags for
the same purpose. This moves mips to the pci_flags approach so
generic code can use the same test across all architectures.
Bjorn Helgaas [Fri, 24 Feb 2012 03:18:57 +0000 (20:18 -0700)]
microblaze/PCI: remove unused pci_flags
pci_flags is initialized to zero and never modified (I think this was just
copied from powerpc). Therefore, "(pci_flags & XX)" is always false and
"!(pci_flags & XX)" is always true, and we can remove all references
to pci_flags.
CC: Michal Simek <monstr@monstr.eu> CC: microblaze-uclinux@itee.uq.edu.au Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Bjorn Helgaas [Fri, 24 Feb 2012 03:18:56 +0000 (20:18 -0700)]
arm/PCI: remove arch pci_flags definition
The PCI core provides a pci_flags definition (currently __weak), so drop
the arm definition in favor of that.
We EXPORT_SYMBOL(pci_flags) as arm did previously. I'm dubious about
this: no other architecture exports it, and I didn't see any modules in
the tree that reference it.
CC: Rob Herring <rob.herring@calxeda.com> CC: Russell King <linux@arm.linux.org.uk> CC: linux-arm-kernel@lists.infradead.org Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Bjorn Helgaas [Fri, 24 Feb 2012 03:18:56 +0000 (20:18 -0700)]
alpha/PCI: replace pci_probe_only with pci_flags
Some architectures (alpha, mips, powerpc) have an arch-specific
"pci_probe_only" flag. Others use PCI_PROBE_ONLY in pci_flags for
the same purpose. This moves alpha to the pci_flags approach so
generic code can use the same test across all architectures.
Bjorn Helgaas [Thu, 23 Feb 2012 21:29:23 +0000 (14:29 -0700)]
PCI: make pci_flags always available
If we move resource assignment functions into the core, we'll still
need a way for architectures to prevent reassignment, e.g., the
"pci_probe_only" functionality, and we'll need a generic, always
available way the core can test for that. The "pci_flags"
arrangement used by several architectures seems like a convenient
way to do this.
Alan Cox [Mon, 13 Feb 2012 12:59:37 +0000 (12:59 +0000)]
x86/mrst/pci: avoid SoC fixups on non-SoC platforms
The PCI fixups get executed based upon whether they are linked in. We need
to avoid executing them if we boot a dual SoC/PC type kernel on a PC class
system.
Signed-off-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Jacob Pan [Mon, 13 Feb 2012 12:59:20 +0000 (12:59 +0000)]
x86/mrst/pci: v4l/atomisp: treat atomisp as real pci device
ATOMISP on Medfield is a real PCI device which should be handled differently
than the fake PCI devices on south complex. PCI type 1 access is used for
accessing config space this also has other impact such as PM D3 delay. There
shouldn't be any need for reading base address from IUNIT via msg bus.
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Jacob Pan [Mon, 13 Feb 2012 12:59:00 +0000 (12:59 +0000)]
x86/mrst/pci: assign d3_delay to 0 for Langwell devices
Langwell devices are not true pci devices, they are not subject to the 10 ms
d3 to d0 delay required by pci spec. This patch assigns d3_delay to 0 for all
langwell pci devices.
We can also power off devices that are not really used by the OS
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com> Signed-off-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
An un-wanted interrupt is generated when PCI driver switches from
MSI/MSI-X to INTx while shutting down the device. The interrupt does
not happen if MSI/MSI-X is not used on the device.
I confirmed that this problem does not happen if pcie_hp=nomsi was
specified and hotplug operation worked fine as usual.
v2: Automatically disable MSI/MSI-X against following device:
PCI bridge: Integrated Device Technology, Inc. Device 807f (rev 02)
v3: Based on the review comment, combile the if statements.
v4: Removed module parameter.
Move some code to build pciehp as a module.
Move device specific code to driver/pci/quirks.c.
v5: Drop a device specific code until getting a vendor statement.
Yinghai Lu [Fri, 10 Feb 2012 23:33:47 +0000 (15:33 -0800)]
PCI: Fix "cardbus bridge resources as optional" size handling
We should not set the requested size to -2; that will confuse the
resource list sorting with align when SIZEALIGN is used.
Change to STARTALIGN and pass align from start; we are safe to do that
just as we do that regular pci bridge. In the long run, we should just
treat cardbus like a regular pci bridge.
Also fix the case when realloc_head is not passed: we should keep the
requested size.
Signed-off-by: Yinghai Lu <yinghai@kernel.org> Tested-by: Dominik Brodowski <linux@dominikbrodowski.net> Acked-by: Ram Pai <linuxram@us.ibm.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
PCI / PM: Disable wakeup during shutdown for devices not enabled to wake up
If a PCI device is enabled to generate wakeup signals (PME) when put
into a low-power state by runtime PM, it will be still enabled to
generate those signals after the system shutdown, unless its driver's
.shutdown() callback takes care of the wakeup signals generation
setting. Moreover, there are devices that are not enabled to wake
up the system and that are configured by runtime PM to generate
wakeup signals so that (runtime) remote wakeup works with them.
Those devices should be reconfigured during system shutdown so that
they don't generate wakeup signals, but at least some drivers don't
do that. However, that very well may be done by the PCI core so
that drivers don't have to worry about it. For this reason, modify
pci_device_shutdown() to disable the generation of wakeup events for
devices not supposed to wake up the system.
References: https://bugzilla.kernel.org/show_bug.cgi?id=37952 Reported-and-tested-by: Kamil Iskra <kamil.54002@iskra.name> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Yinghai Lu [Sun, 5 Feb 2012 06:55:01 +0000 (22:55 -0800)]
PCI: Fix /sys warning when sriov enabled and card is hot removed
sysfs is a bit stricter now and emits warnings in more cases.
For SRIOV hotplug, we are calling pci_stop_dev() for each VF first
(after we update pci_stop_bus_devices) which remove each VF subdir. So
double check the VF dir in /sys before trying to remove the physfn link.
Signed-of-by: Yinghai Lu <yinghai@kernel.org> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Matthew Garrett [Fri, 3 Feb 2012 15:18:13 +0000 (10:18 -0500)]
PCI: pcie: Add support for setting default ASPM policy
Distributions may wish to provide different defaults for PCIE ASPM
depending on their target audience. Provide a configuration option for
choosing the default policy.
Signed-off-by: Matthew Garrett <mjg@redhat.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Thomas Jarosch [Wed, 7 Dec 2011 21:08:11 +0000 (22:08 +0100)]
PCI: Add quirk for still enabled interrupts on Intel Sandy Bridge GPUs
Some BIOS implementations leave the Intel GPU interrupts enabled,
even though no one is handling them (f.e. i915 driver is never loaded).
Additionally the interrupt destination is not set up properly
and the interrupt ends up -somewhere-.
These spurious interrupts are "sticky" and the kernel disables
the (shared) interrupt line after 100.000+ generated interrupts.
Fix it by disabling the still enabled interrupts.
This resolves crashes often seen on monitor unplug.
Tested on the following boards:
- Intel DH61CR: Affected
- Intel DH67BL: Affected
- Intel S1200KP server board: Affected
- Asus P8H61-M LE: Affected, but system does not crash.
Probably the IRQ ends up somewhere unnoticed.
According to reports on the net, the Intel DH61WW board is also affected.
Many thanks to Jesse Barnes from Intel for helping
with the register configuration and to Intel in general
for providing public hardware documentation.
Signed-off-by: Thomas Jarosch <thomas.jarosch@intra2net.com> Tested-by: Charlie Suffin <charlie.suffin@stratus.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Arjan van de Ven [Tue, 31 Jan 2012 04:52:07 +0000 (20:52 -0800)]
PCI: Annotate PCI quirks in initcall_debug style
While diagnosing some boot time issues on a platform, all that I
could see in the bootgraph/dmesg was that the system was spending
a lot of time in applying one or more PCI quirks... which
was virtually undebuggable.
This patch adds printk's in "initcall_debug" style to the dmesg,
which are added when the user asks for the initcall_debug
(the nr one tool to use when debugging boot hangs or boot time issues)
kernel command line option.
v2: add #includes so quirks can build on non-x86
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Kay, Allen M [Thu, 26 Jan 2012 18:25:53 +0000 (10:25 -0800)]
PCI: check for pci bar restore completion and retry
On some OEM systems, pci_restore_state() is called while FLR has not yet
completed. As a result, PCI BAR register restore is not successful. This fix
reads back the restored value and compares it with saved value and re-tries 10
times before giving up.
Signed-off-by: Jean Guyader <jean.guyader@eu.citrix.com> Signed-off-by: Eric Chanudet <eric.chanudet@citrix.com> Signed-off-by: Allen Kay <allen.m.kay@intel.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Yinghai Lu [Fri, 27 Jan 2012 18:55:15 +0000 (10:55 -0800)]
PCI: pciehp: Disable/enable link during slot power off/on
On a system with a repeater on the system board to support gen2 hotplug,
we found that when an ExpressModule is removed from some slots,
/var/log/messages will be full of "card present/not present" warnings.
It turns out the root complex is continually trying to train the link to
the repeater because the repeater has not been reset.
This patch will disable the link at removal time to allow the repeater
to be reset properly. This also prevents a potential AER message at
removal time.
Also, when testing hotplug on a system under development, we found if we
boot the system without an EM installed, and later hot-add an EM, it
does not work with Linux, but another OS is ok. The root cause is that
BIOS left link disabled when slot was empty at boot time, and other OS
is modifying the link disable bit in link ctrl during power on/off.
So we should do the same thing to disable/enable link during power off/on.
-v2: check link DLLA bit instead of 100ms waiting.
Separate link disable/enable functions to another patch.
Signed-off-by: Yinghai Lu <yinghai.lu@oracle.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Yinghai Lu [Fri, 27 Jan 2012 18:55:12 +0000 (10:55 -0800)]
PCI: pciehp: make check_link_active more helpful
A few changes:
- remove the 'inline' and let the complier decide
- return a bool to indicate whether the link was active
- add a debug message to indicate link state when it beocmes active
Signed-off-by: Yinghai Lu <yinghai@kernel.org> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Yinghai Lu [Fri, 27 Jan 2012 18:55:11 +0000 (10:55 -0800)]
PCI: pciehp: replace unconditional sleep with config space access check
During reviewing
| PCI: pciehp: wait 1000 ms before Link Training check
Linus said:
>...
> That's a *long* time, and it's irritating to the user. It makes the
> user think "the machine is slow".
>...
> And quite frankly, an unconditional one-second delay here seems bad.
>Two seconds was unacceptable, one second is just bad.
Try to access the pci conf of a pci device that is supposed to show up
in 1s. If we can read back a valid vendor/device id, we can return
early.
Related discussion could be found:
https://lkml.org/lkml/2011/12/6/339
-v2: seperate code to pci_bus_read_dev_vendor_id() from pci_scan_device()
and reuse it from pciehp code. Suggested by Matthew Wilcox.
-v3: According to Kenj, don't use array in stack, and don't wait too long
for crs, also return fail status if not found.
Also separate pci_bus_dev_read_vendor_id() change to another patch.
Signed-off-by: Yinghai Lu <yinghai@kernel.org> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
root complex: 80:02.2
pci express modules: have pcie switch and are listed as b0:00.0, b1:02.0 and b1:03.0.
end devices are b2:00.0 and b3.00.0.
VFs are: b2:00.1,... b2:00.3, and b3:00.1,...,b3:00.3
Root cause: when doing pci_stop_bus_device() with phys fn, it will stop
virt fn and remove the fn, so
list_for_each_safe(l, n, &bus->devices)
will have problem to refer freed n that is pointed to vf entry.
Solution is just replacing list_for_each_safe() with
list_for_each_prev_safe(). This will make sure we can get valid n pointer
to PF instead of the freed VF pointer (because newly added devices are
inserted to the bus->devices list tail).
During reviewing the patch, Bjorn said:
| The PCI hot-remove path calls pci_stop_bus_devices() via
| pci_remove_bus_device().
|
| pci_stop_bus_devices() traverses the bus->devices list (point A below),
| stopping each device in turn, which calls the driver remove() method. When
| the device is an SR-IOV PF, the driver calls pci_disable_sriov(), which
| also uses pci_remove_bus_device() to remove the VF devices from the
| bus->devices list (point B).
|
| pci_remove_bus_device
| pci_stop_bus_device
| pci_stop_bus_devices(subordinate)
| list_for_each(bus->devices) <-- A
| pci_stop_bus_device(PF)
| ...
| driver->remove
| pci_disable_sriov
| ...
| pci_remove_bus_device(VF)
| <remove from bus_list> <-- B
|
| At B, we're changing the same list we're iterating through at A, so when
| the driver remove() method returns, the pci_stop_bus_devices() iterator has
| a pointer to a list entry that has already been freed.
Discussion thread can be found : https://lkml.org/lkml/2011/10/15/141
https://lkml.org/lkml/2012/1/23/360
-v5: According to Linus to make remove more robust, Change to
list_for_each_prev_safe instead. That is more reasonable, because
those devices are added to tail of the list before.
Signed-off-by: Yinghai Lu <yinghai@kernel.org> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
When the BIOS does not assign resources for SRIOV BARs, kernel pci
reallocation only goes up one bridge and then gives up, failing to to
get resources for all sSRIOV BARs, even though the range is large enough
in the peer root bus.
Specifically, only the bridge at the a1:02.0 level has its resources
cleared and reallocated. The kernel does not go up to clear the bridge
at the 80:02.0 level.
To make it go to upper levels, during retry, we need to treat "good to have"
resources as "must have".
Only on the last try will we treat good to have resources as optional.
At that time, parent bridge resources will already have been released so
we'll have a chance to get everything assigned with must_have plus
good_to_have for all child devices.
Signed-off-by: Yinghai Lu <yinghai@kernel.org> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Yinghai Lu [Sat, 21 Jan 2012 10:08:23 +0000 (02:08 -0800)]
PCI: Make pci_rescan_bus handle add_list
This allows us to allocate resources to hotplug bridges during
remove/rescan.
We need to move the function to setup-bus.c so it can use
__pci_bus_size_bridges and __pci_bus_assign_resources directly to take
the add_list resource tracking list.
Signed-off-by: Yinghai Lu <yinghai@kernel.org> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Yinghai Lu [Sat, 21 Jan 2012 10:08:22 +0000 (02:08 -0800)]
PCI: Make rescan bus increase bridge resource size if needed
Current rescan will not touch bridge MMIO and IO.
Try to reuse pci_assign_unassigned_bridge_resources(bridge) to update bridge
resources, if child devices need more resources.
Only do that for bridges whose children are all removed already; i.e. don't
release resources that could already be in use by drivers on child devices.
Signed-off-by: Yinghai Lu <yinghai@kernel.org> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
After that b1:03.0 get chance to be reassigned to [f8200000-f86fffff],
but b1:02.0 will not have chance to expand, because b1:03.0 is using in
middle one.
root cause:
b1:02.0 can not be added more range, because b1:03.0 is just after it;
no space between the required ranges.
Solution:
Try to assign required + optional all together at first, and if that
fails, try again with just the required resources.
-v2: seperate add_to_list change() to another patch according to Jesse.
seperate get_res_add_size() moving to another patch according to Jesse.
add !realloc_head->next check if the list is empty to bail early
according to Jesse.
Signed-off-by: Yinghai Lu <yinghai@kernel.org> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
xen/pciback: Support pci_reset_function, aka FLR or D3 support.
We use the __pci_reset_function_locked to perform the action.
Also on attaching ("bind") and detaching ("unbind") we save and
restore the configuration states. When the device is disconnected
from a guest we use the "pci_reset_function" to also reset the
device before being passed to another guest.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
and ends up calling:
driver_bind:
device_lock(dev); <=== TAKES LOCK
XXXX_probe:
.. pci_enable_device()
...__pci_reset_function(), which calls
pci_dev_reset(dev, 0):
if (!0) {
device_lock(dev) <==== DEADLOCK
The __pci_reset_function_locked function allows the the drivers
'probe' function to call the "pci_reset_function" while still holding
the driver mutex lock.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Add missing iounmap in error handling code, in a case where the function
already preforms iounmap on some other execution path.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e;
statement S,S1;
int ret;
@@
e = \(ioremap\|ioremap_nocache\)(...)
... when != iounmap(e)
if (<+...e...+>) S
... when any
when != iounmap(e)
*if (...)
{ ... when != iounmap(e)
return ...; }
... when any
iounmap(e);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Amos Kong [Fri, 25 Nov 2011 07:03:07 +0000 (15:03 +0800)]
PCI: Can continually add funcs after adding func0
Boot up a KVM guest, and hotplug multifunction
devices(func1,func2,func0,func3) to guest.
for i in 1 2 0 3;do
qemu-img create /tmp/resize$i.qcow2 1G -f qcow2
(qemu) drive_add 0x11.$i id=drv11$i,if=none,file=/tmp/resize$i.qcow2
(qemu) device_add virtio-blk-pci,id=dev11$i,drive=drv11$i,addr=0x11.$i,multifunction=on
done
In linux kernel, when func0 of the slot is hot-added, the whole
slot will be marked as 'enabled', then driver will ignore other new
hotadded funcs.
But in Win7 & WinXP, we can continaully add other funcs after adding
func0, all funcs will be added in guest.
drivers/pci/hotplug/acpiphp_glue.c:
static int acpiphp_check_bridge(struct acpiphp_bridge *bridge)
{
....
for (slot = bridge->slots; slot; slot = slot->next) {
if (slot->flags & SLOT_ENABLED) {
acpiphp_disable_slot()
else
acpiphp_enable_slot()
.... |
} v
enable_device()
|
v
//only don't enable slot if func0 is not added
list_for_each_entry(func, &slot->funcs, sibling) {
...
}
slot->flags |= SLOT_ENABLED; //mark slot to 'enabled'
This patch just make pci driver can continaully add funcs after adding
func 0. Only mark slot to 'enabled' when all funcs are added.
For pci multifunction hotplug, we can add functions one by one(func 0 is
necessary), and all functions will be removed in one time.
Signed-off-by: Amos Kong <akong@redhat.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Myron Stowe [Mon, 21 Nov 2011 18:54:19 +0000 (11:54 -0700)]
x86/PCI: Convert maintaining FW-assigned BIOS BAR values to use a list
This patch converts the underlying maintenance aspects of FW-assigned
BIOS BAR values from a statically allocated array within struct pci_dev
to a list of temporary, stand alone, entries.
Myron Stowe [Mon, 21 Nov 2011 18:54:13 +0000 (11:54 -0700)]
x86/PCI: Infrastructure to maintain a list of FW-assigned BIOS BAR values
Commit 58c84eda075 introduced functionality to try and reinstate the
original BIOS BAR addresses of a PCI device when normal resource
assignment attempts fail. To keep track of the BIOS BAR addresses,
struct pci_dev was augmented with an array to hold the BAR addresses
of the PCI device: 'resource_size_t fw_addr[DEVICE_COUNT_RESOURCE]'.
The reinstatement of BAR addresses is an uncommon event leaving the
'fw_addr' array unused under normal circumstances. This functionality
is also currently architecture specific with an implementation limited
to x86. As the use of struct pci_dev is so prevalent, having the
'fw_addr' array residing within such seems somewhat wasteful.
This patch introduces a stand alone data structure and interfacing
routines for maintaining a list of FW-assigned BIOS BAR value entries.
Myron Stowe [Mon, 21 Nov 2011 18:54:07 +0000 (11:54 -0700)]
PCI: Fix starting basis for resource requests
pci_revert_fw_address() is used to reinstate a PCI device's original
FW-assigned BIOS BAR value(s) if normal resource assignment fails.
When attempting to reinstate an address, the point within the resource
tree from which to attempt the new resource request should be the parent
resource corresponding to the device, not the base of the resource tree
(ioport_resource or iomem_resource). For PCI devices this would
typically be the resource corresponding to the upstream PCI host bridge
or P2P bridge aperture.
This patch sets the point within the resource tree to attempt a new
resource assignment request to the PCI device's parent resource and only
if that fails does it fall back to the base ioport_resource or
iomem_resource.
Yinghai Lu [Sun, 5 Feb 2012 06:55:00 +0000 (22:55 -0800)]
PCI: Fix pci cardbus removal
During test busn_res allocation with cardbus, found pci card removal is not
working anymore, and it turns out it is broken by:
|commit 79cc9601c3e42b4f0650fe7e69132ebce7ab48f9
|Date: Tue Nov 22 21:06:53 2011 -0800
|
| PCI: Only call pci_stop_bus_device() one time for child devices at remove
The above changed the behavior of pci_remove_behind_bridge that
yenta_cardbus depended on. So restore the old behavoir of
pci_remove_behind_bridge (which requires stopping and removing of all
devices) by:
1. rename pci_remove_behind_bridge to __pci_remove_behind_bridge, and let
__pci_remove_bus_device() call it instead.
2. add pci_stop_behind_bridge that will stop devices behind a bridge
3. add back pci_remove_behind_bridge that will stop and remove devices
under bridge.
PCI: set pci sriov page size before reading SRIOV BAR
For an SRIOV device, PCI_SRIOV_SYS_PGSIZE should be set before
the PCI_SRIOV_BAR are queried. The sys pagesize defaults to 4k,
so this change is required on powerpc box with 64k base page size.
This is a regression caused due to moving SRIOV init to sriov_enable().
| PCI: delay configuration of SRIOV capability
| The SRIOV capability, namely page size and total_vfs of a device are
| configured during enumeration phase of the device. This can potentially
| interfere with the PCI operations of the platform, if the IOV capability
| of the device is not enabled.
Yinghai Lu [Mon, 30 Jan 2012 11:25:24 +0000 (12:25 +0100)]
PCI: workaround hard-wired bus number V2
Fixes PCI device detection on IBM xSeries IBM 3850 M2 / x3950 M2
when using ACPI resources (_CRS).
This is default, a manual workaround (without this patch)
would be pci=nocrs boot param.
V2: Add dev_warn if the workaround is hit. This should reveal
how common such setups are (via google) and point to possible
problems if things are still not working as expected.
-> Suggested by Jan Beulich.
Linus Torvalds [Fri, 27 Jan 2012 15:56:25 +0000 (07:56 -0800)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (31 commits)
gma500: Fix suspend/resume functions
drm/exynos: fixed pm feature for fimd module.
MAINTAINERS: added maintainer entry for Exynos DRM Driver.
drm/exynos: fixed build dependency for DRM_EXYNOS_FIMD
drm/exynos: fix build dependency for DRM_EXYNOS_HDMI
drm/exynos: use release_mem_region instead of release_resource
agp: fix scratch page cleanup
drm/i915: fixup forcewake spinlock fallout in drpc debugfs function
drm/i915: debugfs: show semaphore registers also on gen7
drm/i915: allow userspace forcewake references also on gen7
drm/i915: Re-enable gen7 RC6 and GPU turbo after resume.
drm/i915: Correct debugfs printout for RC1e.
Revert "drm/i915: Work around gen7 BLT ring synchronization issues."
drm/i915: rip out the HWSTAM missed irq workaround
drm/i915: paper over missed irq issues with force wake voodoo
drm/i915: Hold gt_lock across forcewake register reads
drm/i915: Hold gt_lock during reset
drm/i915: Move reset forcewake processing to gen6_do_reset
drm/i915: protect force_wake_(get|put) with the gt_lock
drm/i915: convert force_wake_get to func pointer in the gpu reset code
...
Linus Torvalds [Fri, 27 Jan 2012 15:53:06 +0000 (07:53 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Fix silent output on Haier W18 laptop
ALSA: hda: set mute led polarity for laptops with buggy BIOS based on SSID
ALSA: hda - Fix silent output on ASUS A6Rp
ALSA: Fix memory leak on error in snd_compr_set_params()
ALSA: ymfpci - Don't create invalid PCM & mixers when AC97 doesn't support
Ryan Mallon [Fri, 27 Jan 2012 06:28:24 +0000 (17:28 +1100)]
gma500: Fix suspend/resume functions
Both the suspend and resume functions incorrectly set psbfb =
to_psb_fb(NULL) outside of the loop over all of the framebuffers. Fix
this by moving the assignment of psbfb inside the loop and removing the
initialisation of fb.
Signed-off-by: Ryan Mallon <rmallon@gmail.com> Acked-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Inki Dae [Fri, 27 Jan 2012 02:54:58 +0000 (11:54 +0900)]
drm/exynos: fixed pm feature for fimd module.
this patch separates fimd specific power on/off function from pm function
and the pm interfaces will call that function for power on or off.
and also removes unnecessary codes of resume function.
Signed-off-by: Inki Dae <inki.dae@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Seung-Woo Kim [Wed, 4 Jan 2012 06:34:32 +0000 (15:34 +0900)]
drm/exynos: fix build dependency for DRM_EXYNOS_HDMI
DRM_EXYNOS_HDMI driver and VIDEO_SAMSUNG_S5P_TV driver should be
not enabled at once because they use same HW blocks. So dependency
for DRM_EXYNOS_HDMI is fixed to check VIDEO_SAMSUNG_S5P_TV=n.
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com> Signed-off-by: Inki Dae <inki.dae@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Linus Torvalds [Thu, 26 Jan 2012 20:46:07 +0000 (12:46 -0800)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/microcode_amd: Add support for CPU family specific container files
x86/amd: Add missing feature flag for fam15h models 10h-1fh processors
x86/boot-image: Don't leak phdrs in arch/x86/boot/compressed/misc.c::Parse_elf()
x86/numachip: Drop unnecessary conflict with EDAC
x86/uv: Fix uninitialized spinlocks
x86/uv: Fix uv_gpa_to_soc_phys_ram() shift
Linus Torvalds [Thu, 26 Jan 2012 20:43:57 +0000 (12:43 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k: Fix assembler constraint to prevent overeager gcc optimisation
mac_esp: rename irq
mac_scsi: dont enable mac_scsi irq before requesting it
macfb: fix black and white modes
m68k/irq: Remove obsolete IRQ_FLG_* definitions
Fix up trivial conflict in arch/m68k/kernel/process_mm.c as per Geert.
Michal Kubecek [Wed, 25 Jan 2012 15:51:05 +0000 (16:51 +0100)]
agp: fix scratch page cleanup
In error cleanup of agp_backend_initialize() and in agp_backend_cleanup(),
agp_destroy_page() is passed virtual address of the scratch page. This
leads to a kernel warning if the initialization fails (or upon regular
cleanup) as pointer to struct page should be passed instead.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz> Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie [Thu, 26 Jan 2012 18:25:54 +0000 (18:25 +0000)]
Merge branch 'drm-intel-fixes' of git://people.freedesktop.org/~keithp/linux into drm-fixes
* 'drm-intel-fixes' of git://people.freedesktop.org/~keithp/linux: (24 commits)
drm/i915: fixup forcewake spinlock fallout in drpc debugfs function
drm/i915: debugfs: show semaphore registers also on gen7
drm/i915: allow userspace forcewake references also on gen7
drm/i915: Re-enable gen7 RC6 and GPU turbo after resume.
drm/i915: Correct debugfs printout for RC1e.
Revert "drm/i915: Work around gen7 BLT ring synchronization issues."
drm/i915: rip out the HWSTAM missed irq workaround
drm/i915: paper over missed irq issues with force wake voodoo
drm/i915: Hold gt_lock across forcewake register reads
drm/i915: Hold gt_lock during reset
drm/i915: Move reset forcewake processing to gen6_do_reset
drm/i915: protect force_wake_(get|put) with the gt_lock
drm/i915: convert force_wake_get to func pointer in the gpu reset code
drm/i915: sprite init failure on pre-SNB is not a failure
drm/i915: VBT Parser cleanup for eDP block
drm/i915: mask transcoder select bits before setting them on LVDS
drm/i915: Add Clientron E830 to the ignore LVDS list
CHROMIUM: i915: Add DMI override to skip CRT initialization on ZGB
drm/i915: handle 3rd pipe
drm/i915: simplify pipe checking
...
Takashi Iwai [Thu, 26 Jan 2012 14:56:16 +0000 (15:56 +0100)]
ALSA: hda - Fix silent output on Haier W18 laptop
The very same problem is seen on Haier W18 laptop with ALC861 as seen
on ASUS A6Rp, which was fixed by the commit 3b25eb69.
Now we just need to add a new SSID entry pointing to the same fixup.
Andreas Herrmann [Fri, 20 Jan 2012 16:44:12 +0000 (17:44 +0100)]
x86/microcode_amd: Add support for CPU family specific container files
We've decided to provide CPU family specific container files
(starting with CPU family 15h). E.g. for family 15h we have to
load microcode_amd_fam15h.bin instead of microcode_amd.bin
Rationale is that starting with family 15h patch size is larger
than 2KB which was hard coded as maximum patch size in various
microcode loaders (not just Linux).
Container files which include patches larger than 2KB cause
different kinds of trouble with such old patch loaders. Thus we
have to ensure that the default container file provides only
patches with size less than 2KB.
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com> Cc: Borislav Petkov <borislav.petkov@amd.com> Cc: <stable@kernel.org> Link: http://lkml.kernel.org/r/20120120164412.GD24508@alberich.amd.com
[ documented the naming convention and tidied the code a bit. ] Signed-off-by: Ingo Molnar <mingo@elte.hu>
Linus Torvalds [Wed, 25 Jan 2012 23:36:44 +0000 (15:36 -0800)]
Merge branch 'for-linus' of git://oss.sgi.com/xfs/xfs
Quoth Ben Myers:
"Please pull in the following bugfix for xfs. We forgot to drop a lock on
error in xfs_readlink. It hasn't been through -next yet, but there is no
-next tree tomorrow. The fix is clear so I'm sending this request today."
* 'for-linus' of git://oss.sgi.com/xfs/xfs:
xfs: Fix missing xfs_iunlock() on error recovery path in xfs_readlink()
Linus Torvalds [Wed, 25 Jan 2012 23:13:04 +0000 (15:13 -0800)]
Merge branch 'fix/asoc' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
* 'fix/asoc' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ASoC: wm2000: Fix use-after-free - don't release_firmware() twice on error
ASoC: wm8958: Use correct format string in dev_err() call
ASoC: wm8996: Call _POST_PMU callback for CPVDD
ASoC: mxs: Fix mxs-saif timeout
ASoC: Disable register synchronisation for low frequency WM8996 SYSCLK
ASoC: Don't go through cache when applying WM5100 rev A updates
ASoC: Mark WM5100 register map cache only when going into BIAS_OFF
ASoC: tlv320aic32x4: always enable analouge block
ASoC: tlv320aic32x4: always enable dividers
ASoC: sgtl5000: Fix wrong register name in restore
Linus Torvalds [Wed, 25 Jan 2012 23:11:57 +0000 (15:11 -0800)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
A fairly simple bugfix for a WARN_ON() which was triggered in the cache
reset support as a result of some subsequent work. There's only one
mainline user for the code path that's updated right now (wm8994) so
should be low risk.
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: Reset cache status when reinitialsing the cache
Li Wang [Wed, 25 Jan 2012 07:40:31 +0000 (15:40 +0800)]
eCryptfs: move misleading function comments
The data encryption was moved from ecryptfs_write_end into
ecryptfs_writepage, this patch moves the corresponding function
comments to be consistent with the modification.
Signed-off-by: Li Wang <liwang@nudt.edu.cn> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
projects / linux-beck.git / log